Vantec Ez Swap 4 Mrk 401st Bk Storage Bay Adapter MRK401STBK User Manual

User's Manual  
RoHS  
Table of Contents:  
1. Introduction  
03  
04  
05  
06  
07  
09  
10  
11  
2. Features/Specifications  
3. System Requirements  
4. Parts Layout  
5. Installation  
6. Installing a Hard Drive  
7. LCD Display  
8. Warranty/Contact  
Table of Content  
1
Microsoft Windows 2000/XP/Vista/7  
Mac G3 processor & greater.  
Intel PentiumII 350 MHz-compatible  
MAC OS 8.6 or greater  
Microsoft Windows 2000/XP/VISTA/7  
1. SATA-equipped system.  
2. For SATA speeds, the system must  
support SATA speciꢀcations.  
1. SATA-equipped system.  
2. For SATA speeds , the system must  
tions.  
4. Parts Layout  
EZ SWAP 4 – Removable Hard Drive Rack  
Lock  
Door  
LCD Display  
Screws hole  
Fan Control  
Power port  
SATA port  
Fan  
Parts Layout  
6
5. Installation  
EZ SWAP 4 – Removable Hard Drive Rack  
Power down the computer and disconnect  
the power cable.  
(Figure 5-A)  
(Figure 5-A)  
(Figure 5-B)  
(Figure 5-C)  
(Figure 5-D)  
2. Dismantle the left & right side of PC cover.  
(Figure 5-B)  
3. Dismantle the front cover of PC.  
(Figure 5-C)  
4. Insert the EZ Swap 4 into the 5.25" bay of the  
computer. (Figure 5-D)  
Installation  
7
5. Tighten the screws to ensure EZ Swap 4 is secure  
to the case. (Figure 5-E)  
(Figure 5-E)  
(Figure 5-F)  
(Figure 5-G)  
(Figure 5-H)  
6. Plug one side of SATA cable into a SATA port on  
the motherboard, plug the other side into the  
EZ Swap 4. (Figure 5-F & 5-G)  
7. Connect the 4 pin power cable to the EZ Swap 4's  
power connector. (Figure 5-G)  
Power Cable  
SATA Cable  
8. Reassemble the case and reconnect the power  
cable of the computer. (Figure 5-H)  
Installation  
8
6. Installing a Hard Drive  
EZ SWAP 4 – Removable Hard Drive Rack  
1. Use the key to unlock the EZ Swap 4 and then  
open the panel. ( Figure 6-A )  
( Figure 6-A )  
2. Insert the SATA hard drive. ( Figure 6-B )  
( Figure 6-B)  
3. Close the panel. ( Figure 6-C )  
( Figure 6-C )  
4. Use the key to lock the EZ Swap 4 to fully activate  
the EZ Swap 4. ( Figure 6-D )  
NOTE :  
EZ Swap 4 has a power security function. When  
there is no hard drive present, the EZ Swap 4 will  
not power on.  
( Figure 6-D )  
Instruction  
9
7. LCD Display Function  
Temperature Display  
Thermometer HDD Indicator  
Fan State Indicator  
Fan RPM  
Fan Settings  
Thermometer  
Fan State Indicator  
Temperature Display  
Fan RPM  
When critical temperatures are reached, the thermometer will flash.  
When the fan is functioning properly, the fan state indicator will have a spinning  
motion. When the fan is working improperly, the fan state indicator will flash.  
Temperature of the hard drive will be displayed in either and .  
(Press “Button + “ and “ Button - “ at the same time to switch between or state.)  
This displays current RPM of your fan.  
There are three choices. L (Low speed/2300RPM) ,  
M(Medium speed/3600RPM), H(High speed/4500RPM).  
Fan Settings  
HDD Indicator  
Button +  
When a hard drive is inserted, the HDD indicator will be lit. Activity is  
shown by flickering or flashes.  
To increase the fan speed.  
To decrease the fan speed.  
Button -  
NOTE :  
When the temperature is over the critical safe levels of (55 // 131)  
or if the fan is working improperly, an alarm will sound for 10 seconds  
and can be muted by pressing any of the fan control button. The alarm  
will ring every 30 minutes until the problem is resolved.  
LCD Display Function  
10  
8. Warranty / Contact  
The EZ SWAP 4 comes with a 1 year limited  
warranty (90 day parts). If your unit should  
become defective within that time frame, please  
on how to receive warranty exchange or repair.  
Cosmetic defects and missing parts are not  
covered under this warranty.  
Please check the contents of the unit to make sure  
you received all parts. Also, check for any cosmetic  
ꢀaws. If any parts are missing or if there are  
cosmetic defects, please contact theretailer from  
which you purchased the unit immediately and  
ask for a replacement.  
Vantec Thermal Technologies  
43951 Boscell Rd.  
Fremont, CA 94538  
tel: 510-668-0368  
fax: 510-668-0367  
Copyright © 2009 Vantec Thermal Technologies. All Right Reserved.  
All Registered Trademarks Belong To Their Respective Companies.  
Warranty / Contact  
11  

West Bend SOHO SHCM100 User Manual
Seagate MOMENTUS 54006 SATA ST9320325ASG User Manual
Seagate CHEETAH 15K6 FC ST3450856FC User Manual
Seagate Cheetah 15K5 FC ST3300655FC User Manual
Samsung A847M User Manual
PYLE Audio PYLE PRO P1001AT User Manual
Panasonic SC AK66 User Manual
Oregon Scientific Radio controlled Clock RM982A User Manual
Numark Industries CDN90 User Manual
Norcent Technologies SDMC 2GB UPC 803802972021 User Manual