Toastmaster Clock Radio E9451 HP34 User Manual

HEATER PROOFERS  
MODEL  
9451-HP12, E9451-HP12  
9451-HP34, E9451-HP34  
Installation and  
Operation  
Instructions  
2M-Z15782, Rev. B March 3, 2014  
E9451-HP12CD  
9451 HP SERIES SERVICE SPECIFICATIONS  
The Heater Proofer is an aluminum transport cabinet with heaters to function  
as a hot food holding cabinet, and/or as a proofing cabinet.  
Width  
The heater, or heat drawer, is slid into place on the floor of the cabinet. An  
electrical socket on the back of the drawer is provided to accept the supplied  
power cord, which is plugged into the drawer through an access hole in the  
back of the cabinet.  
The main power switch on the front of the drawer, when switched “ON”, will  
turn on the light in the switch and turn on the air circulating fan in the drawer.  
The circulating fan will operate continuously while the unit is “ON”.  
The thermostat control knobs are mounted to the left and right of the heat/proof  
switch. The left thermostat knob controls the heat in the cabinet from 1 (low  
heat: approximately 80°F) to 9 (high heat: approximately 185°F). The right  
thermostat knob controls the humidity from 1 (approximately 20% relative  
humidity) to 9 (in excess of 100% relative humidity). Average setting will be  
approx. 6 (approximately 85% relative humidity).  
Top  
Depth  
Height  
Front  
Side  
IL2431  
Size Specifications  
Exterior  
Width  
Interior  
Width  
Weight  
Shipping  
Height  
Depth  
33.3125”  
33.875”  
Height  
15.625”  
51.75”  
Depth  
27.5”  
27.5”  
9451-HP12  
9451-HP34  
30.3125”  
67.5625”  
22.8125”  
23.3125”  
18.125”  
18.125”  
100lbs  
140lbs  
Electrical Specifications  
Model  
Volts  
120V  
Watts  
Phase  
Hz  
NEMA  
5-20P  
9451-HP12CC  
9451-HP12CD  
9451-HP12CDN  
9451-HP12SDB  
9451-HP34CD  
9451-HP34CDN  
9451-HP34SDN  
9451-HWHSFR  
E9451-HP12SD  
E9451-HP34SD  
1.5 kW  
1
50/60 Hz  
3
This equipment is designed to hold food at a constant temperature, and supply humidity for proofing  
when the application applies, this is NOT a cooking appliance. This unit is sold for commercial use only  
by personnel trained and experienced in its operation and is not sold for consumer use in and around the  
home nor for use directly by the general public in food service locations.  
CAUTION  
Before using your new equipment, read and understand all the instructions & labels associated with the  
unit prior to putting it into operation. Make sure all people associated with its use understand the units  
operation & safety before they use the unit.  
All shipping containers should be checked for freight damage both visible and concealed. This unit has  
been tested and carefully packaged to insure delivery of your unit in perfect condition. If equipment is  
received in damaged condition, either apparent or concealed, a claim must be made with the delivering  
carrier.  
Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a  
request for inspection of concealed damage must be made with carrier within 15 days. Be certain to  
retain all contents plus external and internal packaging materials for inspection. The carrier will make an  
inspection and will supply necessary claim forms.  
INSTALLATION  
This unit is equipped for the voltage indicated on the nameplate mounted the side of the unit. They will  
operate on alternating current (AC) only.  
The electrical connection must be made in accordance with local codes or in the absence of local codes  
with NFPA No.70 latest edition (in Canada use: CAS STD. C22.1). The electrical service is provided by a  
cord and plug. Each appliance requires a 120 volt grounded supply. Supply wires must be 14 gauge or  
larger to carry the load for one proofer.  
DO NOT CONNECT TO DIRECT CURRENT (DC).  
WARNING  
THIS APPLIANCE IS EQUIPPED WITH A 3-PRONG (GROUNDED) PLUG FOR YOUR  
PROTECTION AGAINST SHOCK HAZARD AND MUST BE PLUGGED DIRECTLY INTO A  
PROPERLY GROUNDED 3-PRONG RECEPTACLE.  
GENERAL OPERATING PROCEDURES  
Proofing  
Proofing is one of the most important and delicate stages in baking. About 50% of the product volume  
is created in the proofer. Proofing accelerates the fermentation of yeast in a warm moist environment  
causing the dough to rise. The proofer humidity should be between medium high and high. For optimum  
results, rolls should be removed from the hot proofer and transferred to the cold proofer at minimum  
proof. This will ensure that they can be held for 40 minutes without becoming over-proofed.  
4
Operating Instructions  
Startup  
1. Push ON/OFF rocker switch to “ON” position  
2. Push HEAT/PROOF switch to HEAT for heating.  
3. Turn HEAT thermostat knob fully clockwise for pre-heat.  
4. Allow 45 minutes for pre-heating, then turn thermostat to desired setting.  
5. For proofing, push HEAT/PROOF switch to PROOF. DO NOT RUN WATER PAN EMPTY.  
Note: While in proof mode only the element around the water pan is on.  
6. Adjust the heat and humidity thermostat knobs to control desired temp and humidity. 45 min pre-heating.  
Note: The internal air circulation blower will operate continuously when the power switch is turned “ON”.  
ON  
HEAT  
HEATER/PROOFER  
OFF  
PROOF  
POWER  
HEAT  
HUMIDITY  
IL2428  
Heat Knob (Heat Mode)  
The controlling range is 80° to 185°F ( 26° to 85°C) temperatures vary slightly between insulated and non-insulated  
units. The dial has setting from 1 to 9 that do not relate to any specific calibrated temperatures. Temperature settings  
must be obtained through familiarization with the unit. While in the heat mode this knob controls the two elements in  
the air stream, in the “OFF” position the elements are turned off. During the “Proof” mode one of these elements is  
not in use.  
Humidity Knob (Proof Mode)  
To control the humidity range from 30% to 100% humidity, settings must be obtained through familiarization with the  
unit. The dial has a range of 1 - 9 which determins the temperature of the water in the pan, if you have the knob in the  
“OFF” position it will turn the proofing element off. While in proof mode the unit will operate at a lower termperature.  
Allow 45 minutes to pre-heat in both heat & proof cycle.  
Troubleshooting  
CAUTION: Before disassembling unit, electrical power must be disconnected by unplugging the unit. Failure to  
unplug the unit prior to servicing may result in electrical shock.  
Each unit is shipped with an instruction manual to be used as a reference guide for all service areas. The manual  
shows a picture of the drawer, showing the location of electrical components and a description of each. If the unit  
does not operate correctly, or malfunctions for any reason, the following checklist should provide a solution.  
1) Check to make sure cord set is firmly plugged into the power receptacle in the back of the cabinet and  
into the wall outlet.  
2) Check circuit breaker of wall outlet and reset if necessary.  
3) Remove heat drawer from cabinet. Remove bottom cover of drawer. Visually inspect for:  
a) Loose or disconnected wires  
b) Black marks or burning on any components  
c) Loose heating elements.  
4) If any burn marks or discoloration of wires is note on any components along with all wires attached to  
damaged components must be replaced.  
5) If heater element is loose, or if it has broken loose from mounting tabs, the wires will short out on the  
Metal, causing permanent damage. Both the element and main power switch (with wires on switch) must  
be replaced.  
6) If temperature on “L.E.D. Thermometer” is not reading a constant temperature, it must be replaced. If  
temperature has exceeded 200°F (93°C) it must be lowered immediately to maximum temperature of  
5
185°F (85°C).  
3
2
1
10  
9
7
6
8
5
4
See Detail A  
Model: E9451 Heater / Proofer  
SK2574  
Rev. -  
3/19/2012  
6
11  
17  
20  
19  
18  
16  
15  
14  
13  
12  
21  
22  
23  
24  
25  
17  
26  
27  
12  
36  
29  
28  
30  
31  
32  
17  
33  
34  
7
35  
Detail A  
Model: E9451 Heater / Proofer  
SK2575  
Rev. A  
7/3/2012  
7
PARTS LIST  
March 3, 2014, Rev. B  
Toastmaster Heater / Proofer Model: E9451 & 9451  
Fig No  
Part Number  
2R-4FM0705P  
R2-AC1323  
Qty  
Description  
Application  
1
2
3
1
1
2
PULL,ALM DRWR,DIE CST,BUF  
E9451-HP12, 9451-HP12  
BAFFLE  
R2-WH2006  
E9451-HP34, 9451-HP34  
2C-1525  
SCREW 1/4-20X1-1/4 RH ST  
R2-WASSY001  
R2-WASSY003  
R2-WASSY022  
R2-WASSY057  
2I-4FMD345P  
2I-4FMD405P  
2V-4FM0003P  
ASSY,DOOR,CLEAR,NHPL-1836  
ASSY,DOOR,SOLID,NHP-1836  
ASSY,DOOR,RH,E9451-HP12CD  
ASSY,DOOR,RH, SOLID DOOR  
18.63X52.70 GSK, BLK, MAG  
GASKET,BLK,MAG,18.63X16.5  
HINGE,ASSY,2”,S/S  
E9451-HP34CD  
E9451-HP34SD  
E9451-HP12CD  
4
1
9451-HP12SDN, E9451-HP12SD  
E9451-HP34, 9451-HP34  
5
1
E9451-HP12, 9451-HP12  
6
7
2
1
R2-TC0075  
PAN ASSY.  
8
2P-738ABK  
2R-4FMBC01P  
2C-Z15625  
R2-WH2020  
2I-6STRN05P  
R2-WH2014  
2U-WP-6FANS30P  
2C-1493  
4
4
16  
1
6
1
1
7
1
37  
1
1
1
1
1
7
7
1
1
1
1
2
1
1
2
1
2
1
CASTER,5x1.25,SWIVEL,POLY  
CORNER BUMPER J-J-B12 BLA  
SCREW 10-32-1 FLT HD PHIL  
BOTTOM COVER  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
GROMMET,7/16X1/16X1/4X3/4  
ELECT BULKHEAD  
6IN TRANSFLOW FAN 115V/60  
SCREW 8-32X3/8 RHP STL NP  
BULKHEAD, MOTOR  
R2-WH2015  
2C-8833  
SCREW 8-18X1/2 HEX STL NP  
ELEMENT,120V,600W  
2N-6FME755P  
2N-6WH0001P  
2N-6WH0002P  
R2-WH2022  
R2-WH2023  
2C-2582  
ELEMENT,HTPRF 600W/120V  
ELEMENT,HTPRF 900W  
PROBE HOLDER TOP  
PROBE HOLDER BOTTOM  
NUT 1/4-20 HEX STL NP  
WASHER 1/4 SPLIT SS  
2C-Z5557  
R2-AP2102  
R2-WH2012  
2E-50-1382  
2T-66-1150  
2T-66-1121  
R2-AC2337  
2M-Z13089  
2J-50-0029  
2E-50-1355  
2R-50-0726  
2E-50-1357  
PROBE HOLDER  
REAR COVER PLATE  
OUTLET,NEMA 5-20R  
DISC,SNAP,275*F  
THERMOSTAT,85-180 DEG,MEC  
FRONT CONTROL PNL  
GRAPHIC, TM HEAT\PROOF  
LIGHT,PILOT,RED NEON,125V  
SWITCH,ROCKER,SPST,ON-OFF  
KNOB,TEMP.BOARD CONTROL  
SWITCH,ROCKER,DPDP,ON-ON  
Main Power Switch  
Heat / Proof Select Switch  
9451-HP12CDN/SDN, 9451-HP34CDN/SDN, E9451-HP12CC/DC/  
SD, E9451-HP34CD/SC, E9451-HWHSFR  
36  
R2-9300E69R  
1
ECONOMY H/P MODULE  
NI  
NI  
NI  
NI  
NI  
NI  
NI  
NI  
2C-20304-02  
2E-6WH0040P  
2R-50-1319  
R2-06-0160  
R2-AC1330  
R2-AC1331  
R2-AC2515  
R2-AC2516-C  
1
1
1
1
1
1
1
1
NUT WING 1/4-20 STN STL  
CORD,POWER,6’FT LONG H-10  
LATCH, MAGNETIC, CHROME  
CATCH, HW-2G  
E9451-HWHSFR  
E9451-HWHSFR  
9451-HP12  
SIDE, OUTER RIGHT  
SIDE, OUTER LEFT  
SIDE-O/D-LT  
9451-HP12  
9451-HP34  
SIDE-O/D-RT  
9451-HP34  
is a registerd trademark of Toastmaster, A Middleby Company. All rights reserved.  
WIRE GA COLOR  
1
2
16 WHITE  
16 WHITE  
16 WHITE  
16 WHITE  
16 WHITE  
16 WHITE  
16 BLACK  
16 BLACK  
16 BLACK  
1
3
4
5
6
7
8
9
1100W HEAT  
600W HEAT  
7
3
8
10 16 BLACK  
11 16 BLACK  
12 16 BLACK  
600W PROOF  
14 14 BLACK & WHITE  
15 14 BLACK & WHITE  
14  
14  
16 14  
GREEN  
4
9
BLOWER  
IND  
IND  
1
4
14  
14  
8
6
9
11  
12 12  
11  
15  
11  
12  
2
5
5
12  
15  
10  
2
15  
15  
11 12  
12  
12  
7
4
12  
10  
3
2
11  
5
1
2
11  
16  
5
6
5
3
3
7
2
HEAT  
PROOF  
T-STAT  
OVERLOAD  
PROTECTION  
T-STAT  
POWER  
HEAT/PROOF  
HEATER PROOFER  
WIRING DIAGRAM  
SK2749  
REV. -  
12-23-13  
9
Warranty Statement  
Toastmaster warrants equipment that it manufactures to be free from defects in material and  
workmanship. Toastmaster’s obligation is limited to repairing or replacing, at Toastmaster’s option, without  
cost to the customer, any part found to be defective, as well as any labor or material expense required to  
replace the part.  
Length of Warranty  
This warranty is effective for a period of 12 months from the date the equipment is placed in service.  
Exceptions  
This warranty is valid only for the original end user owner/operator of the equipment.  
This warranty does not apply to normal maintenance functions, including (but not limited to)  
improper operation, installation or the use of an improper utility supply.  
This warranty is valid only if the equipment is used in a commercial setting. The equipment  
is designed and constructed for commercial use by trained professionals only. Any use of the  
equipment in private or domestic applications immediately voids this warranty.  
This warranty does not apply to any parts, labor and material expenses for service that is not  
pre-approved and performed by a Toastmaster authorized service agent. Any such service  
immediately voids this warranty.  
This warranty does not apply to any parts, labor and material expenses associated with the  
installation of parts that are not factory-approved for use in the equipment. Any use of such  
parts immediately voids this warranty.  
This warranty is not valid if terms of payment have not been met.  
Parts Warranty  
Parts that are sold to repair our of warranty equipment are warranted for ninety (90) days. The part  
only is warranted, the labor to replace the parts is NOT warranted.  
Portable Equipment  
Toastmaster will not honor service bills that include travel time and mileage charges for servicing any  
products considered “Portable”. These products should be taken to the Service Agency for repair.  
A portable unit is a unit thats designed to sit on a countertop, has a powercord & is less than 50lbs  
installed.  
Toastmaster reserves the right to change the design and specifications of this equipment or any related  
documentation at any time. The end user is not entitled to upgrades resulting from these changes.  
This warranty is exclusive and supersedes all other warranties for the equipment, both expressed and  
implied. There are no implied warranties of merchantability or of fitness for a particular purpose.  
The foregoing is Toastmaster’s sole and exclusive obligation and the end user sole and exclusive remedy  
for any action including breach of contract or negligence. In no event shall Toastmaster be liable for a sum  
in excess of the purchase price of the equipment, or for any prospective or lost profits of the end user.  
is a registerd trademark of Toastmaster, A Middleby Company. All rights reserved.  

Toshiba MK8007GAH User Manual
Technics sl pd887 User Manual
Teac CDR58S XXX User Manual
Tascam CD A550 User Manual
Sunbeam 3289 User Manual
Seagate SAVVIO ST9900805SS User Manual
Seagate Barracuda ST340015ACE User Manual
Samsung SGH C408 User Manual
RCA RS252KM User Manual
Philips Coffeemaker HD8743 User Manual