|
TELUS
i465 Mike Phone
User’s Guide
Class B Digital Device
DECLARATION OF CONFORMITY
Per FCC CFR 47 Part 2 Section 2.1077(a)
As a personal computer peripheral, this device complies with part 15 of
the FCC Rules. Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation. See 47 CFR Sec. 15.19(3).
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation.
Responsible Party Name: Motorola, Inc.
Address: 8000 West Sunrise Boulevard
Plantation, FL 33322 USA
Phone Number: 1 (800) 453-0920
Hereby declares that the product:
Product Name: i465
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
Model Number: H98XAH6JR7AN
FCC-ID: IHDT56KB1
Conforms to the following regulations:
FCC Part 15, subpart B, section 15.107(a), 15.107(d) and section 15.109(a)
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
FCC Notice to Users
The following statement applies to all products that have
received FCC approval. Applicable products bear the FCC logo,
and/or an FCC ID in the format FCC-ID: IHDT56KB1 on the product
label.
Motorola has not approved any changes or modifications to this device by
the user. Any changes or modifications could void the user’s authority to
operate the equipment. See 47 CFR Sec. 15.21.
•
Consult the dealer or an experienced radio/TV technician for
help.
Industry Canada Notice to Users
Operation is subject to the following two conditions: (1) This device may
not cause interference and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
See RSS-GEN 7.1.5.
Motorola, Inc.
Consumer Advocacy Office
600 North US Highway 45
Libertyville, IL 60048
www.hellomoto.com
Note: Do not ship your phone to the above address. If you need to
return your phone for repairs, replacement, or warranty service,
please contact the Motorola Customer Support Center at:
1-800-453-0920 (United States)
1-877-483-2840 (TTY/TDD United States for hearing impaired)
Certain mobile phone features are dependent on the capabilities
and settings of your service provider’s network. Additionally,
certain features may not be activated by your service provider,
and/or the provider's network settings may limit the feature’s
functionality. Always contact your service provider about feature
availability and functionality. All features, functionality, and other
product specifications, as well as the information contained in this
user's guide are based upon the latest available information and
are believed to be accurate at the time of printing. Motorola
reserves the right to change or modify any information or
specifications without notice or obligation.
MOTOROLA and the Stylized M Logo are registered in the US
Patent & Trademark Office. All other product or service names are
the property of their respective owners. Java and all other
Java-based marks are trademarks or registered trademarks of Sun
Microsystems, Inc. in the U.S. and other countries.
© Motorola, Inc., 2009.
Manual Number: NNTN7553A
HELLOMOTO
Introducing your new Motorola wireless phone. Here’s a quick anatomy lesson.
Right Soft Key
Perform function
in lower right
display.
Left Soft Key
Perform function
in lower left
display.
Volume Keys
Messaging Key
Menu Key
From home screen,
open main menu.
Web Key
PTT Button
End/Power Key
End calls, exit
menu system,
turns phone
on/off.
Camera Key
Audio Jack
Speaker
Micro USB
Connector
Talk Key
Make &
answer calls.
On/Off Key
Connects charger
and accessories.
OK Key
In menus & lists,
press to select
highlighted option.
4-Way Navigation
Key
1
check it out
turn it on & off
To turn on your phone, press and hold
.for
a few seconds or until the display turns on. If
prompted, enter your four-digit unlock code.
Voicemail LED
Text Message LED
Bluetooth LED
1
3
Press and hold the
Power Key for a
Press the Navigation key
up, down, left or right
to highlight a menu feature.
To turn off your phone, press and hold
two seconds.
.for
few seconds, or until
the screen lights up,
to turn on your phone.
Note: If you press the
.for more than four
2
seconds, the handset will power “On” in
Customizable rkey
that can be used
to open the
4
Press the rkey
Settings screen.
to select.
2
contents
call a stored phone
your phone number
use GPS with map
features for the
using your handset
store a phone number
volume . . . . . . . . . . . . 41
contents
3
switching to Mike’s
exiting Mike’s Talk
private Mike’s Talk
Caring for the
Recycling . . . . . . . . . . . 84
Export Law
Battery Use and
Specific Absorption
AGPS and Emergency
Motorola Limited
hide or show location
Safety and General
Operational
RF Energy
Compatibility . . . . . . . . 82
Warranty for the
and Canada . . . . . . . . . 90
contents
4
Information From the
Organization . . . . . . . . 95
Wireless: The New
California Perchlorate
Patent and Trademark
Software Copyright
Privacy and Data
Smart Practices While
contents
5
menu map
main menu
1
L
Browser
B
o
J
Recent Calls
•
9)Call Forward
l
N
Memo
Java Apps
Profiles
•
Java System
PT Manager
My Info
E
Messages
•
•
•
•
•
•
Send Message
•
•
•
•
•
•
•
•
My Name
•
•
•
•
•
•
•
•
[Create Message]
Send Picture
Send Event
Send My Info
Send Contact
Configure
Line 1
Voice Mail
Net Alert
Inbox
Line 2
Private ID
Group ID
Carrier IP
IP1 Address
IP2 Address
Drafts
Outbox
M
P
Call Timers
Fax Mail
Sent Items
•
•
•
•
•
•
Last Call
Phone Reset
Phone Lifetime
Prvt/Grp Reset
Prvt/Grp Life
Kbytes Reset
D
0
Datebook
Q
L
Shop
VoiceRecord
Contacts
•
[New VoiceRec]
•
[New Contact]
P
c
Call Forward
p
t
Call Alert
Talk Around
GPS
•
•
•
Go To Talk Around
Setup
Help
Ring Tones
•
•
•
Position
Privacy
•
•
•
•
Vibrate All: On/Off
Ringer
Vibrate
Silent
Interface
H
j
Camera
K
Shortcuts
Media Center
•
•
•
•
•
•
•
•
•
[New Entry]
u
Settings
1)Shortcuts
•
(see next page)
2)Cntcs[New Con...]
3)Recent Calls
4)Contacts
This is the standard Main Menu
layout. Your phone’s menu may be a
little different.
c
Bluetooth
•
•
•
•
•
Hands Free
Link to Devices
Device History
Setup
5)Datebook
6)Messages
7)VoiceRecord
8)Browser
Find Me
6
settings menu
Display/Info
2-Way Radio
Security
•
•
•
•
•
•
•
•
•
Wallpaper
Text Size
Theme
•
•
•
•
•
•
•
•
Tkgrp Silent
•
•
•
•
•
Phone Lock
Tkgrp Area
Keypad Lock
SIM PIN
One Touch PTT
Alert Type
Home Icons
Backlight
Clock
GPS PIN
PTT Quick Notes
On/Off PTT
Store Rcvd Info
PTT Backlight
Change Passwds
Advanced
Menu View
Large Dialing
Language
•
•
•
•
•
•
•
•
Alert Timeout
Headset/Spkr
Connectivity
Reset Defaults
Return to Home
Transmitters
Phone Only
Personalize
Phone Calls
•
•
•
•
•
•
•
•
•
Menu Options
•
•
•
•
•
•
•
•
•
•
•
•
Set Line
Up Key
Any Key Ans
Auto Redial
Call Waiting
Auto Ans
Down Key
Left Key
Right Key
Center Key
Left Sftkey
Right Sftkey
Power Up
Baud Rate
Minute Beep
Call Duration
TTY
Hearing Aid
Notifications
DTMF Dialing
Prepend
Volume
•
•
•
•
•
•
•
•
•
Line 1
Line 2
Messages
Earpiece
Speaker
Keypad
Java Earpiece
Java Spkr
Data
7
use and care
Use and Care
To care for your Motorola phone, please keep it away from:
liquids of any kind
dust and dirt
Don’t expose your phone to water, rain,
extreme humidity, sweat, or other
moisture. If it does get wet, don’t try to
accelerate drying with the use of an
oven or dryer, as this may damage the
phone.
Don’t expose your phone to dust, dirt,
sand, food, or other inappropriate
materials.
extreme heat or cold
cleaning solutions
To clean your phone, use only a dry soft
cloth. Don’t use alcohol or other
cleaning solutions.
Avoid temperatures below 0°C/32°F or
above 45°C/113°F
.
microwaves
the ground
Don’t try to dry your phone in a
microwave oven.
Don’t drop your phone.
8
essentials
Caution: Before using the phone for the first
time, read the Important Safety and Legal
information included in the gray-edged pages
at the back of this guide.
2
Press the navigation keys ;to scroll to
Phone Calls, and press the center key
rto
select it.
symbols
This means a feature is network or
subscription dependent and may
not be available in all areas, or might
not be offered by your service
provider. Contact customer service
for more information.
about this guide
This guide shows how to locate a menu
feature as follows:
Find it:
This means that, from the home screen:
Press the menu key and then press
the Settings menu option
/
>
u
>
Phone Calls
This means a feature requires an
optional accessory.
1
/
u
.
essentials
9
SIM card
battery
insert the SIM card
Battery Use & Battery Safety
•
Motorola recommends you always
use Motorola-branded batteries and
chargers. The warranty does not cover
damage caused by non-Motorola
batteries and/or chargers.
Caution: Use of an unqualified battery
or charger may present a risk of fire,
explosion, leakage, or other hazard.
Improper battery use, or use of a
damaged battery, may result in a fire,
explosion, or other hazard.
•
•
Battery usage by children should be
supervised.
Warning: To avoid loss or damage, do not
remove your SIM card from your phone
unless absolutely necessary.
Important: Motorola mobile devices
are designed to work best with
qualified batteries. If you see a
message on your display such as Invalid
essentials
10
Battery or Unable to Charge, take the
following steps:
Always take your mobile device with
you when you leave your vehicle.
•
Remove the battery and inspect it to
confirm it bears a Motorola “Original
Equipment” hologram;
•
•
When storing your battery, keep it in a
cool, dry place.
It is normal over time for battery life to
decrease, and for the battery to exhibit
shorter runtime between charges or
require more frequent or longer
charging times.
•
•
•
If there is no hologram, the battery
is not a qualified battery;
If there is a hologram, replace the
battery and retry charging it;
•
Avoid damage to battery and mobile
device. Do not disassemble, open,
crush, bend, deform, puncture, shred,
or submerge the battery or mobile
device. Avoid dropping the battery or
mobile device, especially on a hard
surface. If your battery or mobile
device has been subjected to such
damage, take it to a Motorola
If the message remains, contact a
Motorola Authorized Service Center.
•
•
New batteries or batteries stored for a
long time may take more time to
charge.
Charging precautions: When charging
your battery, keep it near room
temperature. Never expose batteries to
temperatures below 0°C (32°F) or
above 45°C (113°F) when charging.
Authorized Service Center before
using. Do not attempt to dry it with an
essentials
11
appliance or heat source, such as a hair
dryer or microwave oven.
battery installation
1
Pull out the connector cover. Slide the
battery door downwards until it is
released from the phone.
•
Use care when handling a charged
battery: Particularly when placing it
inside a pocket, purse, or other
container with metal objects. Contact
with metal objects (e.g., jewelry, keys,
beaded chains) could complete an
electrical circuit (short circuit), causing
the battery to become very hot, which
could cause damage or injury.
Promptly dispose of used batteries in
accordance with local regulations.
Contact your local recycling center for
proper battery disposal.
Warning: Never dispose of batteries in a fire
because they may explode.
essentials
12
battery charging
New batteries are not fully charged.
2
3
Remove the battery door.
charge using the charger
1
Pull out the connector cover, and insert
the charger into the micro USB connector
on your phone as shown.
Push the battery down until it snaps in
place.
4
Replace the battery door and slide it up
while pressing gently until you hear a
click.
charge from your computer
You can partially charge your phone’s
battery by connecting a Motorola-approved
USB cable from your phone’s micro-USB port
to a high power USB connector on a
essentials
13
computer (not a low-power one, such as the
USB connector on your keyboard or
bus-powered USB hub). Typically, USB
high-power connectors are located directly on
your computer.
make a phone call
Enter a phone number and press
,or use a
voice command. See “place a call using a
To hang up press
..
enable security
You must enable security the first time you
power on you phone or within 10 days of first
activation of your phone.
answer a phone call
1
2
3
If you want to answer the call on speaker
phone, press the speaker key
)
.
1
2
Press
You are prompted to enable security.
Press under Yes. A series of screens
K
under Ok.
If you want to answer the call using the
handset, press . To hang up press
,
..
K
If you are using a Bluetooth headset,
press the answer key on your headset. To
hang up press the key again.
followed by the default home page
displays.
3
Press .to return to the home screen.
essentials
14
advanced calling
make a private call
With Private calls service, you use your phone
as a long-range, digital 2-way radio using
one-to-one Private calls or one-to-many group
calls.
feature
call waiting To accept the second call
and put the active call on
hold press
K
under Yes.
Your Private ID is the number at which you
receive one-to-one Private calls.
To accept the second call
and end the active call press
.
.
Talkgroup numbers are numbers through
which you receive one-to-many group calls.
3-way call
Make or receive a phone call
and press 3 Way. Enter
the second phone number,
press and under Join.
/
>
to make a Private call
1
Enter the Private ID you want to call.
,
K
2
Press and hold the PTT button. Begin
talking after your phone emits a chirping
sound.
You cannot make and other
calls during a three-way call,
even if one party hangs up.
3
Release the PTT button to listen.
any key
answer
To answer phone calls by
pressing any key on the
To end the call press
..
keypad press
/
>
u
>
>
On
Note: A Private call ends automatically if there
is no activity on the call for a few seconds.
Phone Calls
>
Any Key Ans
.
essentials
15
Private call, wait for the caller to finish
speaking.
send call alerts
Sending a call alert discretely lets the
recipient know that you want to talk to him or
her on a Private call.
2
3
Press and hold the PTT button and begin
talking after your phone emits a chirping
sound.
When you send a call alert, the recipient’s
handset displays your name and emits a
series of beeps or vibrations.
Release the PTT button to listen.
To end the call press
..
to send a call alert
answer a call alert
When you receive a call alert, you must:
1
Enter the Private ID you want to call as
you would when making a Private call.
2
Press
K
under Alert
.
option
Answer: Begin a Private call with the sender
using the PTT button.
When the message Ready To Alert appears on
the display, press the PTT button until the
message Alert Successful appears.
Queue: Store the call alert to the call alert
queue.
Clear: Dismiss and delete the call alert.
answer a private call
1
When your phone emits a chirping sound
or vibrates to indicate you are receiving a
You cannot receive phone calls or Private calls
until you do.
essentials
16
to answer a call alert
2
3
Select a specific Ring Tone
.
1
2
3
Press the PTT button to start a Private call
with the sender.
Select a type for the entry (Mobile
,
Private
,
,
Work1
,
Work2
,
Home
,
Email
,
Fax
,
Pager
,
Talkgroup
IP
or Other). To store a private ID choose
or
Private
.
Queue the call alert by pressing
K
under
4
Enter the number for the entry and press
under Save when done.
Queue
.
K
or
Clear the call alert by pressing
K
under
contacts
Clear
.
feature
edit/delete
contact
entry
Press
Select a contact and press
Edit. Change the
desired content and press
. Press under Save
K
under Contcs.
store a phone number
or private ID
/
>
You can store a phone number or private ID in
r
K
.
Contacts
:
Find it:
/
>
L
>
[New Contact]
1
Enter a name for the new entry. Each
entry’s name can contain 20 characters.
essentials
17
or Talkgroup ID, press and hold the PTT
button to call the number.
feature
set ringer ID Press
K
under Contacts.
Select a contact and press
Edit. Select Ringer and
choose your desired ring
tone. Press under Done
your phone number and
private ID
/
>
K
.
Find it:
/
>
My Info.
call a stored phone
number or private ID
messaging
Your phone has the ability to use both
MOSMS and Multimedia Messaging Service
(MMS) messaging. The type of messaging
your phone uses will be determined by your
service provider. If your service provider offers
messaging through MOSMS, your phone
sends and receive messages using MOSMS.
Find it:
/
>
L.
1
2
Scroll to the Contacts entry.
If the Contacts entry contains more than
one number, scroll left or right until the
type of the number you want to call is
displayed (Mobile Private, Work1, Work2, Home,
,
etc.).
If your service provider offers MMS, your
phone sends and receives messages using
MMS. Additionally, MMS allows you to send
3
If you chose a phone number, press ,to
call the entry, or if you chose a Private ID
essentials
18
and receive messages that may include text,
pictures, videos, and audio files.
4
Press
K
under Save.
viewing members of a message
group
1 Press /> L, select the Message
message groups
A Message Group allows you to send text or
Multimedia Messaging Service (MMS)
messages to Groups of up to 20 contacts.
Group and press r.
adding a member to a message
group
1
Find it: /> L > [New Msg Group]
1
2
Select [Add Member] and select a contact.
Select the Message Group in Contacts
and press /> Edit.
When you are finished adding members
to the group, press
K
under Done.
2
Select [Add Member] and press
the contact you want to add and press
under Done
r. Select
3
Type in a name for the Message Group in
the Name field.
K
.
Note: If you do not provide a name for the
Message Group, the default name will be
Msg Group followed by the number of group
members. For example, a Message Group
with three members would be named
3
Press K under Save to save your changes.
Msg Group (3)
.
essentials
19
2
Enter the phone number of the person
you want to send the message to and
removing a member from a
message group
press
Contacts or Recent Calls to find the number you
want and press under Done
r
or press
K
under Search. Select
1
Select the Message Group in Contacts
and press /> Edit.
K
.
2
Highlight the member you wish to remove
3
Select Mesg: and enter the text of the
message or to use a quick note press
and press /> Remove Member
>
r.
K
under QNotes and scroll to the quick note
you want.
deleting a message group
1
Press /> L and select the Message
Group.
4
If you want to send the message, press
K
under Send or to delete the message
without sending it, press under Cancel
K
.
2
Press /> Delete Msg Group. When
prompted, press
K
under Yes to delete,
quick notes
or K under No to cancel.
When you are filling in the Message and Subject
fields, you can add ready-made words or short
phrases called Quick Notes. After you add
these words or phrases, you can edit them as
you would any other text.
create and send messages
1
From the home screen press
K
under
Mesgs
>
[Create Message].
essentials
20
1
While you are creating a message, scroll
to or select Message or Subject
option
.
Attach: Attach a picture, audio file or voice
record.
2
3
Press K under QNotes.
Select the quick note you want to insert
into the message.
Cc: Send a copy of this message to
someone else.
Auto Replies: Allows you to create a list of
possible short answers for the recipient to
choose when replying to your message.
4
Press
K
under Send.
mms features
Note: The following features are available only
Priority: Set priority Normal or High
Valid Until: Set a date after which attempts to
deliver the message end, or press
under No Date
.
when using MMS.
K
.
more message options
insert a picture, video, and
audio recording
You can insert one or more pictures, videos,
and audio files from the media center into the
body of the message. You can include text in
the body of your message in addition to these
items.
To view more message fields in a message
you are creating, select ....More....
The following options become available:
option
Subject: Create or edit the subject line.
essentials
21
body of the message. You can include text in
the body of your message in addition to these
items.
insert items
While you are filling in the Mesg field, press
/
, select Insert and choose from Add Picture
Insert Audio Insert Video Capture Video, Capture Picture or
Record Voice
,
1
While you are filling in the Attach field,
press [New] > and select from Browse Pictures
,
,
,
.
Capture Picture
,
Browse Audio, Record Voice, Browse
A list of available pictures, videos, or audio
files appears. You can only insert one item at a
time.
Video, or Record Video
.
A list of available pictures, audio files, or
voice recordings appears.
Select the picture, video, or audio recording
you want to insert.
2
3
Select the picture, audio or voice record
you want to attach.
remove an inserted item
To remove an item from the message you are
creating, highlight it and press
If you want to attach more items, select
[New]
.
K
under Delete.
When finished, press
K
under Done.
Note: You can only attach audio files and
pictures if they are not forward locked and if
their DRM settings do not prevent you from
sending.
attach a picture, video, or audio
recording
You can attach one or more pictures, audio or
voice recordings from your phone into the
essentials
22
Forward locked items are usually copyright
protected, and you cannot share them with
anyone, such as in Private calls or by
uploading them from your phone.
The picture is attached to the message
and saved to the default storage location.
record a video
You can record a video to send with a
message:
take a new picture
1
While you are creating a message, scroll
to any message field and press or
select Attach
1
2
Select Attach
Record and adjust video.
To view the video without saving it, press
under Review
To save the video, press
To discard the video without saving it,
press under Discard
>
[New] > Record Video.
/
>
[New].
2
3
Select Capture Picture. This accesses the
camera.
K
.
3
eor press r.
Take the picture. For instructions on how
to take the picture see “camera” on
K
.
4
When you have captured the picture you
4
The video is attached to the message and
saved to the media center in the default
storage location.
want, press
To discard the picture, press
Discard. You can then take another picture.
When finished, press under Done
K
under Save.
K
under
5
K
.
essentials
23
2
3
Scroll to the attachment you want to
remove.
create a new voice record
You can create a new voice record to send
with a message:
Press
/
>
Unattach.
1
2
3
Press
/
or select Attach
>
[New].
use drafts
When you save a message as a draft, it is
saved in the drafts folder.
Select Record Voice
.
Say the message you want to record into
the microphone.
Find it: Press
/
>
E
>
Drafts.
4
When you are finished recording, press
1
2
Select the draft you want to edit.
r
.
To edit the fields you want to change,
follow step 2 through step 4 in “create
and send messages” above.
5
6
When finished, press
K
under Done.
The voice record is attached to the
message and saved to the media center
and the list of voice records.
delete a draft
When you send a draft, it is removed from the
Drafts folder.
remove an attachment
To remove an attachment in a message you
are creating:
1
To delete a message in the Drafts folder
without sending it, scroll to the message
1
Select Attach
.
essentials
24
you want to delete and press
K
under
1
2
From the Inbox, highlight a message.
Press Threading, and select from None
Subject, or Sender
Delete
.
/
>
,
2
Press
K
under Yes to confirm.
.
Note: Threading by subject is dependant
upon your service provider.
inbox
Find it: Press
/
>
E
>
Inbox.
read from the message center
1
From the home screen press
K
under
receive a message
Mesgs
>
Inbox.
1
To view the message press
To dismiss the message notification press
under Exit
K
under Read.
2
3
Select the message you want to read.
2
To reply to the message, press K under
K
.
Reply
.
While reading a text and numeric message
that contains a phone number, you can press
delete unread messages
1
,
to call that number.
Scroll to the message you want to delete.
Press under Delete and under Yes to
confirm.
threaded inbox
The threaded Inbox allows you to organize
your messages by subject or sender.
2
K
K
essentials
25
forward a message
send a call alert
1
Press
/
>
Forward
.
1
View the message.
2
Create and send your message.
Embedded objects and attachments are
included when you forward a message.
2
Highlight the Private ID or Talkgroup ID
you want to alert.
3
Press
/
>
Alert.
4
Push the PTT button.
lock and unlock messages
Locked messages cannot be deleted until you
unlock them.
make a group call
1
2
3
View the message.
1
View the message you want to lock or
unlock.
Press
/
.
Highlight the Talkgroup ID you want to
call.
2
Press
/
>
Lock Message or Unlock Message.
call a number in a message
4
Select Talkgroup
.
If a message you receive contains a phone
number, Private ID, or Talkgroup ID in the From
field, the To field, the Cc field, the Subject field, or
the body of the message, you can call or send
a call alert to that number.
5
Push the PTT button.
essentials
26
Contacts type you want to assign the
number or email address.
store message information to
contacts
If a message you receive contains a phone
number, Private ID, Talkgroup ID, or an email
address in the From field, the To field, the Cc
field, the Subject field, or the body of the
message, you can store this information to
6
Press
K
under Save.
reply to a message
To reply to a message:
1
2
View the message you want to reply to.
To reply to the sender only, press
under Reply or press under Reply All to
reply to all recipients.
Contacts
.
K
1
2
View the message.
K
Highlight the number or email address
you want to save.
3
A list of short phrases appears. Select any
of these phrases to add it to your
3
Press
To store the number or email address as a
new entry, select [New Contact]
/
>
Save Number or Save Email.
messages or select [Create Reply]
.
4
.
4
Edit any message fields you want to
change.
To store the number or email address to
an existing entry, select the entry.
5
Press
K
under Send.
5
With the Contacts type field highlighted,
press
;left or right to display the
essentials
27
use auto replies
embedded objects and
attachments
If a message contains pictures, videos, or
audio files in the body of the message,
highlight each picture, video, or audio
recording to view or play it.
If the message you are replying to was sent
with auto replies, it contains a numbered list
of possible replies for you to send. Press the
number of the reply you want to send. The
reply is sent immediately without further
action.
If a message contains a picture, video, or
audio recording as an attachment, open the
attachment to view the picture or play the
video or audio recording.
go to a website
If a message contains one or more website
URLs, you can go to that website.
1
2
View the message.
open attachments
Highlight the website URL you want to go
to.
1
View the message.
2
Highlight the attachment you want to
open. Attachments appear at the end of a
message.
3
Press /> Go To Website.
Note: The entire URL must appear in the
message to allow you to open the website.
3
Press r.
Attachments of an unknown type cannot be
opened, but can be deleted.
essentials
28
1
2
View the message.
save an embedded picture,
video, or audio recording
To save a picture, video, or audio recording
that is part of the body of a message you
receive:
Highlight the picture, video, or audio
recording you want to delete and
press
/.
3
Select Delete Picture Delete Video, or Delete Audio.
,
1
2
View the message.
save attachments
Highlight the picture, video, or audio
recording you want to save.
1
View the message.
2
Highlight the attachment you want to
save.
3
Press
/.
4
Select Save Picture Save Video, or Save Audio.
,
3
Press
/
>
Save Attachment.
The item will save in the default storage
location.
Selected items save to the default storage
location.
delete an embedded picture,
video, or audio recording
To delete a picture, video, or audio recording
that is part of the body of a message you
receive:
delete attachments
1
View the message.
2
Highlight the attachment you want to
delete.
essentials
29
3
Press
Press
/
>
Delete Attachment
.
3
Press
K
under Cancel.
4
K
under Yes to confirm.
sent items
The Sent Items box holds sent messages.
outbox
The Outbox holds all unsent messages.
forward items from sent items
Find it: Press
/
>
E
>
Outbox.
1
Scroll to the message you want to
forward.
resending failed messages
from the outbox
2
3
Press
Make edits if you wish, select the
recipient and press under Send
/
>
Forward.
1
Scroll to the message you want to resend
or press the number of the message you
want to resend.
K
.
check delivery status
If a message was successfully sent and you
set the message to confirm delivery, you can
check the delivery status:
2
Press
K
under Resend.
cancel an unsent message
1
Highlight the message you want to
cancel.
1
2
Scroll to the message you want to view.
Press
/
>
Delivery Status.
2
Press
/.
essentials
30
The following options become available:
delete sent messages
1
2
3
Scroll to the message you want to delete.
option
Signature: Allows you to create a signature
that is automatically inserted at the end of
your messages. Signatures can be edited
before sending the message.
Press
Press
K
K
under Delete
.
under Yes to confirm.
delete all unlocked sent messages
Quick Notes: Lets you create new Quick Notes
and edit or delete Quick Notes you created.
1
Press
/
>
Delete All.
2
Press
K
under Yes to confirm.
Cleanup: Controls how long messages remain
in the Inbox and Sent Items before being
deleted.
customize messaging
Delivery Rpt: Allows you to be automatically
notified when your message is delivered.
Find it:
/
>
E
>
/
>
Setup.
This option is available from many
context-sensitive menus.
Memory Size: Shows a report on used and free
memory in your phone.
MMS Setup: opens a submenu to set MMS
options.
Text Msg Setup: opens a submenu to set text
messaging options.
essentials
31
The following options become available:
manage memory
Your text Inbox and Sent Items hold 200
messages each. The Outbox, and Drafts
folder hold up to 30 messages each. If they
are full, you cannot receive messages, send
messages, or save drafts until you delete
some items.
option
Friendly Name: Allows you to create a friendly
name. Your friendly name is displayed in the
From field on other iDEN handsets when
your message is received.
Downloads: Controls whether your phone
downloads new messages. Set this option
to Automatic if you want your phone to
download new messages automatically.
Select Manual if you want your phone to
prompt you before downloading new
messages.
To view the amount of memory available in
your text inbox:
Find it: Press
/
>
E
>
/
>
Setup
>
Memory Size
.
mms setup
Replies: Lets you create or edit and delete
reply phrases you created.
Find it:
/
>
E
>
/
>
Setup
>
MMS Setup.
This option is available from many
context-sensitive menus when you are using
MMS.
text message setup
Find it:
/
>
E
>
/
>
Setup
>
Text Msg setup.
essentials
32
This option is available from many
context-sensitive menus when you are using
MOSMS.
edit quick notes or replies
You can edit only Quick Note phrases you
have created.
The following options become available:
1
2
3
From the Setup menu, select Quick Notes, or
select MMS Setup
>
Replies.
option
Select the quick note or reply you want to
edit.
Srvc Cntr No: Allows you to enter a service
center number.
Edit the text and press
r.
Expire After: Allows you to set the number of
days before a message expires.
delete quick notes or replies you have
created
new quick notes and reply
phrases
1
From the Setup menu, select Quick Notes, or
select MMS Setup
>
Replies.
create quick notes or replies
2
Scroll to the quick note you want to
delete.
1
From the Setup menu, select Quick Notes, or
select MMS Setup
>
Replies
.
3
Press
Press
K
K
under Delete
.
2
3
Select [New Quicknote], or [New Reply]
.
4
under Yes to confirm.
Enter text from the keypad and press
r.
essentials
33
delete all quick notes or replies you
have created
2
Choose a clean up option from the
following list:
1
From the Setup menu, select Quick Notes, or
select MMS Setup
option
>
Replies
.
Off: Messages are never automatically
deleted.
2
3
Press
Press
/
>
Delete All
.
K
under Yes to confirm.
5 Messages: If you have more than 5
messages, messages are deleted in the
order they were received, starting with the
oldest, until 5 are left.
cleanup options
The cleanup option controls how long
messages remain in the Inbox and Sent Items
before they are deleted. You set the cleanup
option for the Inbox and Sent Items
separately.
10 Messages: If you have more than 10
messages, messages are deleted in the
order they were received, starting with the
oldest, until 10 are left.
1 Day Messages are deleted if they are older
than 1 day.
:
The clean up option deletes only read,
unlocked messages and sent messages.
3 Days: Messages are deleted if they are
older than 3 days.
Find it:
/
>
E
>
/
>
Setup
>
Cleanup.
1
Select Inbox or Sent Items
.
With these options, messages are deleted
when you exit the message center after
setting the option.
essentials
34
delete a thread
option
F-In F-Out: Messages are deleted as
To delete a thread from the Inbox:
necessary on an FirstIn FirstOut basis.
1
2
3
From the Inbox, select a thread.
Custom: Lets you create a clean-up option of
up to 199 days for the inbox.
Press
Press
/
>
Delete Thread.
K
under Yes to confirm.
3
Press
K
under Yes to automatically
message notifications
When you receive a message, your phone
notifies you with text on the display, a
notification tone or vibration.
delete messages now or press
No to delete messages later.
K
under
delete all messages
To delete all read, unlocked messages from
the Inbox, all messages in the Drafts folder, or
all successfully sent messages in the Outbox:
You can access the message or dismiss the
notification.
If you dismiss the notification, the message is
not deleted. It can be accessed through the
message center.
Find it:
/
>
E
.
1
2
3
Select Inbox
,
Drafts Sent Items, or Outbox.
,
If you are not on a phone call when you
receive a message, your phone sounds a
notification tone every 30 seconds until you
access the message or dismiss the alert.
Press
Press
/
>
Delete All.
K
under Yes to confirm.
essentials
35
If you are on a call when you receive a
message, your phone may sound a
notification tone during the call or after you
end the call, depending on how you set your
notification options.
option
Delay All: Tones for all types of messages are
held until you end calls.
Note: Delay All is the default setting.
To set notification options during a call press
set notification options
To control whether your phone sounds
message notification tones while you are on a
phone call:
/
>
Call Setup
>
Notifications.
using your handset
as a modem
Your phone can be connected to a computer
via USB for use as a modem. For more
specific information on how to setup your
phone for use with your computer please visit
www.motorola.com/support and look under the FAQ
section.
Find it:
/
>
u
>
Phone Calls Notifications.
>
Select from the following options:
option
Receive All: Tones sound during calls for all
types of messages.
Msg Mail Only: Tones sound during calls for
mail messages; tones for all other types of
messages are held until you end calls.
essentials
36
basics
status indicators
Status indicators are shown at the top of the
home screen:
display
The home screen shows when you turn on
1. 2. 3. 4.
5. 6. 7.
the phone. To dial a number from the home
Ready
10:05pm 10/23
screen, press number keys and
,.
Time
Date
Note: Your home screen may look different.
Ready
10:05pm 10/23
Time
Left Soft
Right Soft
Key Label
Date
Key Label
1
Signal Strength Indicator: Vertical bars
show the strength of the network
Left Soft
Right Soft
Key Label
connection. You can’t make or receive
Key Label
calls when
~
shows.
Soft key labels show the current soft key
functions. For soft key locations, see page 1.
basics
37
2
3
Active Phone Line:
line 1 is ready to make calls;
phone line 2 is ready to make calls.
$
indicates phone
indicates
main menu
All your phone’s features can be accessed
through the main menu. You can set the main
(
Speaker On/Off: Sounds associated with
Private calls and group calls can be set to
come through the earpiece rather than
through the speaker.
menu to appear as List View or Icon View
.
Find it: Display/Info Menu View.
/
>
u
>
>
4
5
6
Ringer Vibe/Off: Your phone is set to not
ring.
text entry
Some features let you enter text.
Message Indicator: Shows when
you receive a text message.
Your phone provides convenient ways to enter
words, letters, punctuation, and numbers
whenever you are prompted to enter text (for
example, when adding a Contacts entry or
when using Text Messaging).
Packet Data: Your handset is ready to
transfer packet data or is transferring
packet data when it shows a blinking
arrow.
change the character input mode
7
Battery Charge Indicator: A fuller battery
1
When you see a screen where you can
enter text, press to change the
character input mode.
indicates a greater charge. Recharge the
battery when your phone shows Low Battery
/
.
basics
38
2
Select one of the following options:
word method
entry method
The Word text input method predicts the
word you are typing by comparing the letters
entered with dictionaries of words, and
provides the most commonly-used word as
you type. You may use up to two dictionaries,
one for a primary language and another for a
secondary language.
Alpha
Word
Press a key several times for
different characters.
Enter words using a predictive
text entering system that lets
you enter a word with fewer
keypresses.
enter a word using “word” method
character input
Text
Settings
Selects the desired entry
languages and Word Prediction
features.
1
Select the Word character input method.
Insert
Selects a item to be inserted,
such a picture, an audio/video clip
or a voice recording.
2
Press the corresponding keys to enter a
word (for example, to enter the word Bill
press F G H H ). (If you make a
,
mistake, press
D
to erase a single
Note: available only when
composing a message using
MMS.
character. Press and hold
entire entry.)
D
to delete an
3
To accept a word and insert a space,
press
I
.
basics
39
To accept a word completion (such as
Billion when you entered Bill), press the
navigation key to the right. To enter Bill
press the navigation key to the left.
alpha method
To enter characters by tapping the keypad:
,
1
Select the Alpha method.
2
Press the corresponding keys to enter a
word. For example, to enter the word Bill
press F G H H . If you make a
If next word prediction is turned on, when
you hit space, you will be presented with
a predicted word option. For example, if
you enter Go, you will be presented with a
predicted word option such as to. Press
the navigation key right to accept the
predicted word.
,
mistake, press
D
to erase a single
character. Press and hold
entire word.
D
to erase an
3
To enter a symbol character, press
B
or
A
and the key for the symbol you wish to
enter.
If two or more word combinations result
from the sequence of letters entered, a
down arrow will be displayed. Press and
hold the navigation key down to display a
list of possible word choices.
By default, the first letter of an entry is
capitalized.
When word completion is turned on, if
you get a word you don’t want, you can
press the navigation key up or down to
see more word choices.
basics
40
volume
navigation key
Press the volume keys up
or down to:
Press the navigation key
up, down, left, or right to
scroll to items in the
display. When you
•
•
•
turn off an incoming
call alert
highlight the desired
change the earpiece
volume during calls
item, press
it.
rto select
change the ringer
volume from the
home screen
handsfree speaker
You can use your phone’s handsfree speaker
to make calls without holding the phone to
your ear.
Tip: You can quickly set your ringer to
Vibrate All by holding the down volume
key in the home screen.
During a call, press
K
under Spkr to turn the
handsfree speaker On.
The handsfree speaker stays on until you
press under Spkr again.
K
basics
41
visit www.motorola.com/support and look under the
FAQ section.
transmitters
Consult airline staff about the use of the
Transmitters Off feature during flight. Turn off
your phone whenever instructed to do so by
airline staff.
features for the hearing
impaired
Transmitters Off turns off your phone’s calling
and Bluetooth features in situations where
wireless phone use is prohibited, but you can
use the phone’s other non-calling features
when Transmitters is turned Off.
using your phone with a
hearing aid
For best results use the following optimization
procedures and handset setting. They
generally apply as well for users with cochlear
implants:
Find it:
/
>
u
>
Advanced
>
Transmitters
>
Off.
use GPS with map
software
Your phone can be connected to a PC, laptop,
or PDA via USB for use as a GPS receiver. For
more specific information on how to setup
your phone for use with your computer please
optimize your handset position and
orientation
While in a phone call slide your phone up and
down, then left and right until best
microphone coupling is obtained. You also
may need to adjust your hearing aid (HA)
volume setting.
basics
42
Approximate telecoil location is within
6-13 mm of this location.
Off - Shut off
M - Microphone
T - Telecoil
Approximate telecoil location is just
above the battery.
If your HA has a telecoil, activate its switch,
then also rotate the handset as illustrated to
align the telecoils.
choose your hearing aid setting
Find it: Phone Calls Hearing Aid.
/
>
u
>
>
Note: Some automatically switched hearing
aids may need an auxiliary switching magnet.
1
Set this option to Microphone. Microphone
coupling is now optimized.
If you are unsure whether your HA is telecoil
equipped or needs an auxiliary magnet,
please refer to your HA user guide or contact
a hearing aid professional or supplier.
or
2
Set this option to Telecoil. Handset meets
US federal requirements for telecoil
coupling sound or set this option to Off
(factory default). This is the setting for non
HA users.
basics
43
TTY
security features
feature
feature
turn On TTY Press
/
>
TTY
u
>
phone lock
To lock the phone press
feature
Phone Calls
>
>
Use TTY
>
On.
/
Phone Lock
Auto Lock
>
u
>
Security
>
>
Lock Now or
choose TTY Press
/
>
TTY
u
>
>
Type
.
mode
Phone Calls
>
.
keypad lock To lock the keypad press
Select from TTY
,
VCO or HCO.
/
>
u
>
Security
>
change the
TTY baud
rate
Press
/
>
TTY
u
>
Baud.
Keypad Lock
Auto Lock
> Lock Now or
Phone Calls
>
>
.
Select 45.45 or 50.00
.
Shortcut: To lock the
keypad press
change TTY While in the TTY call, press
mode
during a call
/
> *.
/
>
In Call Setup
>
TTY
>
Type.
enable SIM Press
PIN
change SIM Press
PIN
/
>
.
u
>
Security
>
SIM PIN
>
On
Select from TTY
,
VCO or HCO.
/
>
u
>
>
Security
>
Change Passwords
SIM PIN.
Note: You can make emergency calls on a
basics
44
main attractions
Items in the media center can be sent in
MMS messages and with Bluetooth. See
media center
The media center lets you access pictures,
audio recordings, and videos stored in your
phone’s memory.
Pictures in the media center can be sent in
The following audio recordings can be
accessed through the media center:
•
•
Voice records
Audio files supported by the Media Center
include:
Musical ring tones in the list of ring
tones
Format
.au
Sampling Rates/Bit Rates
8 KHz/8 kbps
•
•
Audio recordings saved from MMS
messages received
8 KHz
.midi
.mp3
.wav
Audio recordings downloaded to your
phone
8 KHz/8 kbps
8 KHz/64 kbps
12kbps
.amr
main attractions
45
Image files supported by the Media Center
include:
video player
1
2
3
From the Media Center, scroll left or right
to Media: Video.
Format
.png
Max. Image Size (in pixels)
128 x 160
Select the video you wish to view, and it
will begin to play.
128 x 160
.gif
640 x 480
.jpg
To stop the video, press the navigation
key down. To play the video again,
128 x 160
.wbmp
press
r.
Video files supported by the Media Center
include:
camera
Format
Frame Rate and
You can save pictures taken with the
integrated camera in your phone’s memory,
and can access them through the Media
Center.
Max. Image Size (in pixels)
AVI
15fps 128 x 96
15fps 128 x 96
15fps 128 x 96
H.263
MPEG
Pictures you take can be sent via Private Calls,
Bluetooth, or MMS message. You can also
set them as your phone’s wallpaper.
main attractions
46
access the camera
option
To access the camera, press
e
.
Lighting: Turn on the spotlight On before
taking a picture in low light conditions. You
To take pictures aim the camera lens and
press under Capture or press
can set it up to be Normal or Low Light
.
K
r.
Self Timer: Delay capturing the picture for a
selected number of seconds. The values
To save the picture, press
To discard the picture without saving it, press
under Discard
From the camera viewfinder, you can press
to enter Menu Options
r.
are: Off (default), 10 seconds
seconds
,
15 seconds, and 20
K
.
.
To turn off the timer before the picture is
captured, press under Cancel
Picture Quality: Adjust the picture quality to
Normal or Fine
Picture Size: Set up the picture size to XL
(640x480) L (320x240) M (160x120) S (128x96), or
WP (128x160). You can also set picture size
/
.
K
.
The following options become available:
.
option
Media Center: Opens the Media Center
application.
,
,
,
Record Video: To record a video
from the viewfinder by pressing
right.
left and
Zoom: To set the camera’s zoom to 1x, 2x, or
4x.
Memory Usage: Shows the total amount of Used
Free, and total Capacity of the phone’s
memory.
,
main attractions
47
The following options become available:
option
Camera Setup: To access the camera set up
option
screen.
Ask for Name: If this option is On, you are
prompted to enter a name for each picture
before saving. Otherwise, pictures are
automatically saved with the date and a
number as their names.
access the media center
You can access the media center from the
camera at any time by pressing
Center, except when you are using the Camera
/
>
Media
Shutter Sound
:
Sets the default sound the
camera makes when it takes a picture.
Sets the default value for the Picture
Setup menu or viewing the memory screen.
Default Size
:
The media center contains all your pictures,
music files, and videos located on your
Size option.
phone’s memory. Press
to filter your results.
A
and
*
or
A
and
Default Quality: Sets the default value for the
quality of the picture.
#
customize the camera
Find it:
e
>
/
>
Camera Setup
main attractions
48
When you make or receive a Private call, your
phone automatically determines whether the
phone you are engaged in a Private call with is
able to receive each of these items. Your
phone saves this information for as long as
the Private ID is on your Recent Calls list or is
saved in your Contacts. Your phone updates the
saved information each time you make or
receive a call to or from that Private ID.
PTX features
With Push To View features, your phone can
send and receive the following items through
Private calls with other phones that have this
capability:
•
•
•
•
•
•
Short text messages1
Pictures1
Datebook events
My Info
Note: You cannot send PTT feature items
during Talkgroup calls.
Contact information
Location information1
send messages
The Push to Send Messages feature
lets you send short text messages through
Private calls.
You can choose to send messages, pictures,
events, My Info Contacts or Location information to
,
the Private ID you are engaged in a Private call
with, Private IDs on the Recent Calls list, and
Private IDs stored in Contacts
When you send a message, it appears on the
display of the phone you are engaged in the
Private call with.
.
1. Additional charges may apply.
main attractions
49
begin a message from the PT Manager
begin a message and choose a
recipient
You can begin a message during a Private call,
The PT Manager lets you select the Private ID
you want to send the message to from Contacts
or the Recent Calls list.
from the Contacts list, the Recent Calls list, or from
Find it:
/
>
N
>
Send Contact Browse.
>
the PT Manager
begin a message during a Private call
While in a Private call, press
.
Then select Contacts or Recent Calls to see a list of
entries from the Contacts or the Recent Calls list
that can receive messages.
/
>
Use PTT Feature
>
Send Message.
create messages
Note: The first time you send a message,
Messaging Fees May Apply Continue? appears and you
After you have begun a message and chosen
a recipient, a screen appears that lets you
create the text of the message you want to
send. Your message may be up to 400
characters long.
are prompted to respond. Press
to acknowledge the message.
K
under Yes
begin a message from the Contacts or
the Recent Calls list
You can choose from a list of ready-made
words or short phrases called Quick Notes.
You can use a Quick Note as it is or edit it
before you send it. Editing a Quick Note
1
From the Contacts or the Recent Calls list,
select the entry containing the Private ID
you want to send the message to.
2
Press
/
>
Use PTT Feature
>
Send Message.
main attractions
50
changes the Quick Note for this message only
and will not change the Quick Note on the list.
send pictures
You can send pictures stored in the Media
Center through Private calls. The picture you
send appears on the Private call recipient’s
display.
send a completed message
After you have completed your message,
press the PTT button to send it.
If the recipient accepts the picture, their
phone saves the picture. The picture then
appears in that phone’s recent call list.
receive messages
When you receive a message, a message
notification appears on the display.
The first time you send a stored picture after
turning the phone on, Picture Fees May Apply
Continue? appears and you are prompted to
respond.
To view the message: Press
K
under Read
under
.
To dismiss the message press
K
Dismiss
.
Note: You cannot make or receive Private
calls while transmitting or receiving a picture.
reply to a message
send a picture during a call
1
2
3
View the message.
1
While in a Private call, press
K
under
>
Press under Reply
K
.
Picture or press
/
>
Use PTT Feature
Create the message and press the PTT
button to send it.
Send Picture.
main attractions
51
A list of pictures that can be included in a
Private call appears.
A list of contacts that have Private IDs and
are able to receive pictures appears.
2
3
4
Select the picture you want to send.
5
Select the name of the person you want
to send the picture to.
Press the PTT button to send the picture.
6
7
Press the PTT button to send the picture.
Wait while the picture is transmitted. The
Private call is temporarily interrupted
while a picture is transmitted.
When prompted, press the PTT button to
resume the Private call.
5
When prompted, press the PTT button to
resume the Private call.
from the PT Manager:
Find it: Send Picture.
/
>
N
>
1
Select A Contact or A Recent Call
start a call by sending a picture
A list of contacts that have Private IDs and
are able to receive pictures appears.
from the media center
Find it:
/
>
Media Center
Scroll left or right to Media: Pictures
Select the picture you want to send.
Press
2
Select the name of the person you want
to send the picture to.
1
2
3
4
.
3
Select Browse Picture or Capture Picture.
/
>
Send Via...
>
Send Via PTT
.
4
Press the PTT button to send the picture.
Select A Contact or A Recent Call
main attractions
52
5
Once picture has been sent, when
prompted press the PTT button to resume
the call.
send a datebook event
to send a datebook event during a
private call
receive a picture
1
While in a Private call press />
Use PTT Feature
>
Send Event.
When someone sends you a picture, your
phone emits a tone or vibrates and a message
appears asking if you want to accept the
picture.
Note: If these options do not appear on
the menu, the Private ID you are engaged
in a private call with is not able to receive
Datebook events.
Pictures you receive are saved to your phone’s
memory. They are accessible through the
media center.
2
3
4
If you want to create a new datebook
event, press
K
under New and create the
event in your datebook. If you want to
chose an existing event do so.
When you see a message asking if you want
to accept the picture, press Yes to accept or No
to decline.
If the event is a recurring event: Select
This Event Only to send only the event
selected. Select Repeat Events to send all
occurrences of the event.
clear a picture from the display
If you want to clear a picture from your
phone’s display while still on a call, press
Push the PTT button to send the event.
/
>
Clear Screen.
main attractions
53
1
2
Select or remove the fields you want to
send.
send my info
1
While in a Private Call press />
Send via PTT > Send My Info, and push the PTT
Press
K
under Done.
button to send.
The information your phone sends always
includes My Name, and Private. You may also
or
send Line 1 Line 2, and Carrier IP, depending on
,
2
From the home screen press
My Info
or press
recipient from Contacts, Recent Calls or
Memo, and press
button to send.
/>
your sending options.
>
/
K
>
Send via PTT. Enter a Private ID
under Browse to chose a
automatic sending
To control whether you send your information
automatically:
r. Push the PTT
Find it:
/
>
PT Manager
>
Configure
>
PTT My Info
>
set my info sending option
Auto Send
You can control what portion of the
information in My Info is sent and whether it is
sent automatically in every call or only when
you choose to send it.
1
2
Select On or Off
When you make a call in which your
information is sent automatically, the
name you entered in the My Name field of
My Info appears on the display of the
Find it:
/
>
PT Manager
>
Configure
>
PTT My Info
>
Info to Send
recipient’s phone, even if your name and
main attractions
54
Private ID are not stored in the recipient’s
Contacts.
turn PTT features on and off
You can turn your phone’s ability to send and
receive messages, pictures, and Datebook
events on and off.
send contact information
1
2
3
While in a Private Call press />
Find it:
/
>
u
>
2-Way Radio
>
On/Off PTT
.
Use PTT Feature
.
1
Check or uncheck Messages, Pictures or
Events.
Select Send Contact and select the contact
information you want to send.
You cannot turn your phone’s ability to send
and receive My Info and contact information
on and off.
Push the PTT button to send.
or
1
2
From the home screen press />
PT Manager
>
Send Contact.
Enter the Private ID number of the person
you want to send the Contact information
to or press
K
under Browse
.
3
Select from Recent Calls
,
Contacts, or Memo.
4
Select the contact information you want
to send and push the PTT button.
main attractions
55
one touch PTT
option
Find it:
/
>
u
>
2-Way Radio
>
One Touch PTT.
One Touch PTT sets your phone to do any of
the following each time you press the PTT
button from the home screen:
Send Message: Go to the first screen to send a
message.
Send Picture: Go to the first screen to send
pictures. See “send pictures” on page 51.
option
Off: Nothing happens when you press the
PTT button from the home screen.
Send Event: Go to the first screen to send a
Datebook event.
Send My Info: Go to the first screen to send My
Last Call: Call the most recent Private ID or
Group on the recent calls list.
Send Contact: Go to the first screen to send a
contact. See “send contact information” on
Assigned No.: Call a Private ID you assign.
Enter the number using your keypad, or
press
Calls, or Memo
K
under Search. Select Contacts
.
,
Recent
quick PTT
Quick PTT lets you quickly make a call,
when accessing any Private IDs on your
phone.
Note: If you are entering a Talkgroup
number, enter before the number.
#
main attractions
56
To view a list of Contacts with Private IDs in
After choosing what PTT item you are
sending, select a contact and press the
PTT button to send.
Contacts
:
Find it:
To move between Contacts
use the left or right, or press
and
To make a Private call:
/
>
Quick PTT
or
,
Recent Calls, or Memo,
;
A
and
*
or
2
Select Configure to configure your PTT Quick
A
#
.
Notes
,
PTT My Info
,
One Touch PTT, or On/Off PTT
.
Bluetooth®
1
2
3
Select the entry you want.
Press under Done
Push the PTT button.
Find it:
/
>
c
K
.
turn Bluetooth on or off
You can turn your phone’s Bluetooth feature
on or off. While Bluetooth power is on, your
phone can communicate with other devices.
PT manager
The PT Manager lets you quickly access PTT
features, and other Private call features, from
the main menu.
Find it:
/
>
c
>
Setup Power
>
1
2
Select On to power Bluetooth On.
Find it:
Select Quick PTT
Event Send My Info
/
>
PT Manager
Send Message
Send Contact, or Configure
Select Name if you wish to assign a name
to your handset.
1
,
,
Send Picture
,
Send
,
,
.
main attractions
57
3
Select Find Me Time to determine the
amount of time in which your handset can
be found by other Bluetooth devices.
3
Your handset requires that you create a
bond in order to connect with a Bluetooth
headset. Press
K
under Yes when you
are prompted to bond with the headset.
You can turn off Bluetooth if you want to
prolong battery life or if you enter an area
where Bluetooth is prohibited.
4
Enter the Bluetooth pass key.
Some Bluetooth devices ship with
Bluetooth PINs. Please refer to your
Bluetooth device’s user guide to locate
this information.
make a Bluetooth connection
connect your handset with a Bluetooth
headset
If a device ships without a Bluetooth PIN,
then you can enter any PIN for that
device. To establish a connection to that
device, enter the same PIN for both your
phone and the device. For example, if you
enter 1234 as the device’s PIN, then enter
1234 as your phone’s PIN.
Find it:
/
>
c
>
Hands Free> [Find Devices]
1
Follow the instructions on your Bluetooth
headset to set it up to be found.
2
Once your Bluetooth headset is set to be
found press
phone will scan for the Bluetooth headset
until it finds it. Press when you see
ron your handset. Your
5
Press
K
under Ok.
r
This handset offers the Bluetooth auto pair
feature with auto pair compatible Motorola
the name of the Bluetooth headset on
your screen.
main attractions
58
devices. When bonded via Bluetooth with a
certain device, the pin will not be required.
If the Audio Devices list contains only one device,
your phone will try to connect to it.
connect your handset with another
Bluetooth device
send information via Bluetooth
Your handset can transfer Contacts entries,
Datebook events, audio files, pictures and
videos to another Bluetooth device.
Find it:
/
>
c
>
Link To Devices
1
Select the device you want from the list of
found devices on your screen.
The receiving device must be within 32 feet
(10 meters) of your phone in order to connect.
2
Create a bond if you are prompted to do
so.
Note: Files sent or received may be up
to 1 MB, depending on your service
provider.
If you have previously connected to a device,
the device will be stored on your phone so
you can connect with it easily.
sending information
use Bluetooth during a call
You can connect with available Bluetooth
devices during a call.
1
From within Contacts, datebook, or Media
Center, select the Contacts entry,
Datebook event, audio file, video, or
picture you want to send.
1
2
While in a call, press
Select the audio device you want to
connect to from the list of Hands Free Devices
/
>
Use Bluetooth.
2
Press
/
>
Send Via...
>
Bluetooth.
.
main attractions
59
3
Select the device you want to transfer the
contact information to, or search for the
device by selecting [Find Devices]
.
4
If prompted, bond with the device.
Your phone connects with the devices and
transfers the information.
main attractions
60
call features
•
•
pictures sent or received
Datebook events received
turn off a call alert
You can press the volume keys to turn off a
call alert before answering the call.
The recent calls list displays up to 20 of the
most recent calls and call alerts.
1
2
3
Press
/
>
Recent Calls
.
recent calls
The recent calls list contains information
associated with calls you have made and
received and call alerts you have received.
Scroll through the list.
To view more details of the item
press
r.
When you send or receive Private calls, the
recent call list contains the following PTX
items with those calls:
store an item to contacts from
recent calls
Phone calls, Private calls, My Info, Contacts or
Location entries received from other phones
can be stored to the Contacts list from the
Recent Calls list.
•
•
•
contact information received
My Info received
short text messages received
call features
61
Find it:
/
>
Recent Calls.
caller ID
1
Scroll to or select the item you want to
store.
Caller ID allows people to identify a caller
before answering the phone by displaying the
number of the incoming call. If you do not
want your number displayed when you make
a call, just follow these easy steps.
2
Press
K
under Save to store the
information as a new entry in the
Contacts list.
or
To block your phone number from being
displayed for a specific outgoing call:
3
Select an existing contact and update the
information.
1
2
3
Press * 6 7
Enter the number you want to call.
Press
.
4
Press
K
under Done to save your changes.
,
.
redial
To permanently block your number, call your
customer service provider.
To redial your last outgoing call, press and
hold or push the PTT button if it was a
private call.
,
call forward
Call forwarding sends calls to the phone
numbers you specify. You can forward all calls
to one number or forward missed calls to
call features
62
different numbers depending on the reason
you missed the call. You can forward phone
lines 1 and 2 independently.
voice names
You can place calls by speaking commands to
your phone if you have previously assigned a
voice name to your contacts.
Find it:
/
>
Call Forward.
1
To forward all calls select All Calls and select
To to enter the phone number you want all
your calls forwarded to.
assign voice names to contacts
1
2
3
4
Press
[New Contact]
K
under Contcs and select
.
or
Assign a name, phone number and select
[Options]
2
You can specify a forwarding number for
each type of missed call by selecting
Detailed and choosing the following options:
.
Select Voice Name and follow the prompt to
record the voice name.
If Busy: When your handset is on a call or
transferring data.
Press
K
under Back and
K
under Save.
If No Answer: When you do not answer on
the first 4 rings.
place a call using a voice name
Press the speaker key until you are
prompted to say the voice name.
The handset will automatically place the call.
1
)
If Unreachable: When your handset is out of
coverage or powered off.
call features
63
are in a location where your phone's GPS
antenna has established a clear view of the
open sky and your local emergency response
center has the equipment to process location
information. Because of the limitations of this
feature, always provide your location, to the
best of your knowledge, to the emergency
response center when you make an
emergency calls
Your service provider programs one or more
emergency phone numbers that you can call
under any circumstances. Emergency calls
can be made without a SIM card, when your
phone is locked, or when the SIM card is
blocked.
emergency call
.
Note: Emergency numbers vary by country.
Your phone’s preprogrammed emergency
number(s) may not work in all locations, and
sometimes an emergency call cannot be
placed due to network, environmental, or
interference issues.
Note: Emergency calls cannot be placed
while the keypad is locked, or if your phone is
displaying a No Service message on the screen.
To unlock the keypad, press /*
.
Dial 911 or your local emergency number to
be connected to an emergency response
center. If you are on an active call, you must
end it before making an emergency call.
international calls
If your phone service includes international
dialing, press and hold to insert your local
0
international access code (indicated by +).
Then, press the keypad keys to dial the
country code and phone number.
When you make an emergency call, your
phone’s GPS Enabled feature can help
emergency service personnel find you, if you
call features
64
speed dial
voicemail
Each phone number stored in Contacts is
assigned a Speed Dial number, which you can
use to call that number.
To receive voice mail messages, you must
first set up a voice mail account with TELUS.
receiving a message
When you receive a voice mail message, New
VoiceMail Message appears on the display.
1
From the home screen, use the keypad to
enter the Speed Dial number assigned to
the phone number you want to call.
2
3
Press
Press
#
.
To call your service provider’s voice mail
system and listen to the message:
,
.
1
Press
To dismiss the message notification:
Press or Back
If the caller leaves a message, this icon
K
under Call.
turbo dial
2
The first nine entries in your contacts are set
for turbo dial. They can be called by pressing
and holding the speed dial number
(1 through 9).
•
r
.
3
appears on the display, reminding you that
you have a new message.
call features
65
advanced voice mail with fax
fax mail Indicator
Mike's Advanced Voice Mail with Fax allows
you to receive faxes directly to your handset
and store them along with your voice
messages until you are ready to print. Follow
the voice mail prompts to print the fax to a fax
machine. It ensures privacy, convenience and
eliminates the need for a separate fax line.
Your handset is equipped with a Fax Mail
indicator to notify you when you have
received a fax through Mike's Advanced Voice
Mail with Fax.
Shortcut: From the home screen press
under Mesg
-
>
Fax Mail.
When you receive a new fax, New FaxMail
Message appears on the display.
When you subscribe to Mike's
Advanced Voice Mail with Fax, you will
receive a fax number from your point of
feature activation. If you have not received a
fax number, please contact the nearest
TELUS dealer or call TELUS client care.
Your handset will alert you audibly until you
press
-
under Call or
-
under Exit.
net alerts
When you receive a Net Alert, a notification
Please see www.telusmobility.com for
more details of TELUS Voice Messaging
services.
appears on the display.
If you dismiss the notification, this icon
appears on the display, reminding you that
you have a new message.
2
call features
66
Mike’s Talk Around TM
Note: This feature may not be offered by your
service provider.
•
•
Use up to 10 channels
Communicate with standalone Mike’s
Talk Around radios
With Mike’s Talk Around, you can make and
receive Two-Way Radio calls without network
Note: You cannot use Mike’s Talk Around
with older Family Radio Services products.
coverage. If you are travelling outside your
service provider's coverage area, receiving a
poor signal, or otherwise want to temporarily
avoid using your service provider's network,
you can switch to Mike’s Talk Around and talk
with anyone on your code and channel who is
within range.
The following features and main menu items
are unavailable while in Mike’s Talk Around:
•
•
•
•
•
•
•
On-network phone or Private calls
Data transmission
Incoming message notification
Datebook
Note: Range will vary based on terrain,
man-made structures and atmospheric
conditions.
Call forwarding
Mike’s Talk Around lets you:
Call Timers
•
Use code or private mode operation
Call alerts
Mike’s Talk Around TM
67
1
2
From the Talk Around idle screen, press
TA Options and press
switching to Mike’s Talk
Around
/
>
r.
Select Exit Talk Around
.
To set your phone to Mike’s Talk Around:
Switching to Network Please Wait displays. After a few
seconds, the network idle screen appears.
1
2
From the home screen press
Talk Around and press
/>
r
.
talk range
Select Go to Talk Around
.
While in Mike’s Talk Around mode, phones
should be a minimum of 6 feet apart to
maximize performance and improve
transmission range.
Switching to Talk Around Please Wait displays.
After a few seconds, the Talk Around idle
screen displays. When TA Ready displays,
you can begin using Mike’s Talk Around.
While in Mike’s Talk Around, this icon
displays.
4
channels and codes
Your phone has 10 channels and 15 codes.
Channels are divided into sets of frequencies.
Other parties may be talking on the same
channel. Codes minimize interference from
other parties when you are sharing the same
channel.
exiting Mike’s Talk
Around
To switch to network mode:
Mike’s Talk Around TM
68
Mike’s Talk Around opens to the last code and
channel used on your phone. You can view the
code and channel your phone is currently set
to on the Talk Around idle screen.
4
Select a channel.
5
When you are finished, press
Back to return to the Mike’s Talk Around
idle screen.
K
under
For code calls, all parties must be on the
same channel and code. For private Mike’s
Talk Around calls, the person you are calling
must be in Mike’s Talk Around and set to the
same channel to receive your call.
To set a code:
1
From the Talk Around idle screen, press
K
under Edit
.
2
3
4
5
Scroll to Code
Press
Select a code.
When you are finished, press
.
Note: When making a code call, all parties
that are on your code and channel can hear
your conversation.
K
under Edit.
K
under
Back to return to the Talk Around idle
screen.
setting channels and codes
To set a channel:
1
From the Talk Around idle screen, press
under Edit
making code calls
To make a code call:
K
.
2
3
Scroll to Channel
.
1
From the Talk Around idle screen or the
channel and code edit screen, press and
Press under Edit
K
.
Mike’s Talk Around TM
69
hold the PTT button. Transmit appears on
the first line of display. Begin speaking
after your phone emits the Mike’s Talk
Around tone.
Note: An incoming Mike’s Talk Around call
can be terminated at any time by pressing
.
.
receiving all Mike’s Talk Around
calls
Note: The Mike’s Talk Around tone consists of
4 rapid beeps.
If you set the code to Receive All, your phone
can receive Mike’s Talk Around transmissions
from any phone that is set to the same
channel, regardless of the code (1-15). When
you receive transmissions with the code set
to Receive All, the code that the transmission
was received on will replace Receive All on the
display.
2
Release the PTT button to listen.
If you receive an error message:
•
•
No one is on your channel or code.
You are out of range.
receiving code calls
When you receive a code call, Receive will
appear on the display. After hearing the Mike’s
Talk Around tone, you have 6 seconds to reply
before the call times out.
Note: You cannot initiate a code call when the
code is set to Receive All
.
To set the code to Receive All
:
To reply to the call, press the PTT button.
1
2
From the Mike’s Talk Around idle screen,
press under Edit
K
.
Scroll to Code
.
Mike’s Talk Around TM
70
3
4
5
Press
Select Receive All
When you are finished, press
Back to return to the Mike’s Talk Around
idle screen.
K
under Edit.
private only
To set Mike’s Talk Around to ignore code calls,
so that you only make or receive private
Mike’s Talk Around calls, set your code to
.
K
under
Pvt Only
.
To set the code to Pvt Only
:
To reply to a call with the code set to Receive All
:
1
From the Talk Around idle screen, press
•
Press the PTT button.
K
under Edit
.
2
3
4
5
Scroll to Code
Press
Select Pvt Only
When you are finished, press
.
private Mike’s Talk
Around calls
If you want to have a private conversation
without other parties listening in, you can
make a private Mike’s Talk Around call. The
person you are calling must be in Mike’s Talk
Around and set to the same channel to
receive your call.
K
under Edit.
.
K
under
Back to return to the Talk Around idle
screen.
Mike’s Talk Around TM
71
•
•
The person that you are trying to reach
is set to a different channel.
making a private Mike’s Talk
Around call
The person that you are trying to reach
is out of range.
1
Enter the PTN of the person you want to
call on your channel. If the PTN is more
than 10-digits, enter the last 10-digits of
the PTN, or scroll to a number or name in
Contacts or the Recent Calls List.
receiving a private Mike’s Talk
Around call
The number or name of the person who is
calling will appear in the display.
2
3
Press and hold the PTT button. Begin
speaking after your phone emits the
Mike’s Talk Around tone.
To reply, press the PTT button.
Release the PTT button to listen.
ending code calls and private
Mike’s Talk Around calls
The number or name of the person you
are calling will appear in the display.
Code calls and private Mike’s Talk Around calls
will end automatically after 6 seconds of
inactivity.
If you receive an error message:
•
•
The PTN you entered is invalid.
The person that you are trying to reach
is in network mode.
The Talk Around idle screen will display.
Mike’s Talk Around TM
72
Note: A private or code Mike’s Talk Around
call can be interrupted during the 6 second
idle time by another code call or private call.
setup options
You can set up Mike’s Talk Around options on
the TA Options screen. You can access this
screen in both network and Talk Around
modes.
making emergency calls
while in Mike’s Talk
AroundTM mode
If you attempt to make an Emergency 911 call
while in Talk Around mode, your phone will
automatically exit Talk Around mode and
attempt to find a network signal.
To access setup options:
1
2
Press /> Talk Around or TA Options.
Select Setup
.
You can set the following Mike’s Talk Around
options:
•
Direct Launch: Launch directly into Mike’s
Talk Around when you select Talk Around
from the main menu.
If you are out of network coverage your phone
will not be able to make an emergency 911
cellular call until you go back into the network
coverage area.
•
State Tone: Have an alert sound notify you
that you have used Mike’s Talk Around
for a specified interval.
You must wait until the phone reconnects to
the network before attempting to make an
emergency 911 cellular call.
Mike’s Talk Around TM
73
using direct launch
using state tone
To set your phone to launch Mike’s Talk
Around when you select Talk Around from the
main menu:
To set your phone to alert you after you have
used Mike’s Talk Around for a specified
interval:
1
From the Setup screen, scroll to Direct
Launch and press
1
From the Setup screen, scroll to State Tone
and press
r
.
r.
2
Select On
.
2
Select the interval after which you want
the tone to sound.
Note: If Direct Launch is set to On, the Mike’s Talk
Around setup options will be unavailable from
the main menu. However, you can still access
setup options while in Mike’s Talk Around by
For example, if you select 1 hour, you will be
notified every hour that you are in Mike’s Talk
Around.
pressing
/
and selecting > TA Options
>
Setup.
To turn off State Tone:
To turn off Direct Launch:
1
From the Setup screen, scroll to State Tone
and press
1
2
From the Setup screen, scroll to Direct
Launch and press
r.
r
.
2
Select Off
.
Select Off
.
TA Options will now display when you select
Talk Around from the main menu.
Mike’s Talk Around TM
74
customize
4
When you are finished, press
K
under
ring tones
Done
.
To set the ring tone your phone makes when
you receive phone calls, call alerts, message
notifications, pictures sent using Send via PTT
or Datebook reminders:
Note: This icon
you set your phone to Silent. This icon
appears on the display if you set the phone to
,
appears on the display if
5
Vibrate All
.
Find it:
/
>
Ring Tones
set your phone to vibrate
1
2
Make sure Vibrate All is set to Off
.
You can set your phone to vibrate instead of
making a sound when you receive all phone
calls, Private calls, Talkgroup calls, call alerts,
message notifications, pictures sent using
Send via PTT, and Datebook reminders.
Scroll through the list of ring tones and
select the one you want to assign.
Vibrate sets your phone to vibrate instead
of making a sound. Silent sets your phone
to neither vibrate nor make a sound.
Find it:
/
>
Ring Tones
>
Vibrate All
3
Select the features you want to assign the
ring tone to.
Set this option to On or Locked
.
customize
75
Setting this option to On lets you turn Vibrate All
off by pressing the up volume control. Setting
this option to Locked requires you to press and
hold the up volume control to turn Vibrate All off.
The Locked option helps prevent you from
accidentally turning Vibrate All off.
4
When you are finished, press
K
under
Done
.
backlight
Set the amount of time that the display and
java apps. backlights remain on, or turn off the
backlight feature to extend battery life.
To set Vibrate All to On or Locked using the volume
controls:
Find it:
/
>
u
>
Display/Info
>
Backlight
Press the volume controls to turn down the
volume as far as possible to set Vibrate All to On
.
Continue to hold the down volume control to
LED indicators
You can turn off the Bluetooth, messaging,
and voicemail indicators.
set Vibrate All to Locked
.
To set your phone to vibrate instead of making
a sound for some features but not others:
Find it:
Bluetooth LED
/
,
>
u
>
Display/Info
>
Backlight
Off
>
Find it:
/
>
Ring Tones
Message LED, or VMail LED
>
1
2
3
Make sure Vibrate All is set to Off
.
Select Vibrate from the list of ring tones.
Select the features you want to set to
make no sound.
customize
76
wallpaper
datebook
Set a previously saved photo or picture as a
wallpaper (background) image in your phone’s
external display, internal screen or throughout
all menu screens.
feature
create
datebook
events
To create a new Datebook
event press
/
>
Datebook
>
[New Event]
.
Find it:
/
>
u
>
Display/Info
>
Wallpaper
see datebook To see a calendar event
event
press
left or right to see the day
and up or down to see
/
>
Datebook. Press
;
1
2
Select Wallpaper
Scroll through the list of pictures and
press to select a picture.
.
;
r
the events.
You can set the wallpapers to change
automatically after a certain period of time by
turning on the Auto Cycle feature located in the
event
reminder
When an event reminder
occurs press
Press under Back to close
the reminder.
K
under View.
K
Wallpaper menu. You can select from 5 minutes
,
15 minutes
,
1 hour
,
8 hours
,
Daily, or Startup
.
customize
77
datebook setup
feature
receive
datebook
events via
PTT
To view the information
while still in the Private call
Find it:
/
>
Datebook
>
/
>
Setup
You can view or change these options:
press
r.
options
The 5 most recent events
received from a Private ID
are stored with that Private
ID on the recent calls list.
Start View: Sets Datebook to start in day view,
week view, or month view when you
access Datebook.
Daily Begin: Sets the beginning of your day.
This is the earliest time of day displayed in
week view, if you have a 12-hour day view.
To store events to the
Datebook press
K
under
Save while viewing the event
Delete After: Sets the amount of time
Datebook waits to delete an event after it
occurs.
you want to store.
Time Shift: Lets you shift the times of all
Datebook events. This is useful if you are
traveling to a different time zone.
Alert Timeout: Sets the amount of time a tone
continues to sound when you receive a
Datebook reminder.
customize
78
without your request or permission. GPS-
enhanced 911 is not available in all areas.
options
Clock: Controls whether the time and date
appear on the home screen; sets time and
date format; sets year.
set your privacy options
Find it:
/
>
GPS Privacy
>
Select from the following options:
hide or show
location information
option
Restricted: No Java or similar software
applications may view the location of your
phone. However, location information may
still be available to the phone’s owner, fleet
manager, or account administrator.
Your phone is equipped with a Location
feature for use in connection with location-
based services that may be available in the
future.
Unrestricted: All applications may view the
location of your phone, without notifying
you.
Turning Location On will allow the network to
detect your position using GPS technology,
making some applications and services easier
to use. Turning Location off will disable the
GPS location function for all purposes except
911, but will not hide your general location
based on the cell site serving your call. No
application or service may use your location
customize
79
option
Ask Access: When an application attempts to
view the location of your phone, you will be
prompted to give permission. However,
location information may still be available to
the phone’s owner, fleet manager, or
account administrator.
change GPS PIN
When you receive your phone, your GPS PIN
is 0000.
To change your GPS PIN press
/
>
u
>
Security
>
Change Passwords
>
GPS PIN. Enter the
current GPS PIN and enter the new four to
eight digit GPS PIN. Re-enter the new four- to
eight-digit GPS PIN to confirm.
customize
80
Legal and Safety
•
•
•
•
•
United States Federal Communications Commission, Code
of Federal Regulations; 47 CFR part 2 sub-part J.
Safety and General Information
This section contains important information on the safe and
efficient operation of your mobile device. Read this
information before using your integrated multi-service
portable radio.*
American National Standards Institute (ANSI) / Institute of
Electrical and Electronics Engineers (IEEE). C95. 1-1992.
Institute of Electrical and Electronics Engineers (IEEE).
C95. 1-2005 Edition.*
Exposure to Radio Frequency (RF) Energy
International Commission on Non-Ionizing Radiation
Protection (ICNIRP) 1998.
Your mobile device contains a transmitter and receiver. When it is
ON, it receives and transmits RF energy. When you communicate
with your phone, the system handling your call controls the power
level at which your phone transmits.
Ministry of Health (Canada). Safety Code 6. Limits of
Human Exposure to Radio frequency Electromagnetic
Fields in the Frequency Range from 3 kHz to 300 GHz,
1999.
Your mobile device is designed to comply with local regulatory
requirements in your country concerning exposure of human beings
to RF energy.
•
•
Australian Communications Authority Radio
communications (Electromagnetic Radiation - Human
Exposure) Standard 2003.
Portable Radio Product Operation and EME
Exposure
ANATEL, Brazil Regulatory Authority, Resolution 303 (July
2, 2002) “Regulation of the limitation of exposure to
Your Motorola radio product is designed to comply with the
following national and international standards and guidelines
regarding exposure of human beings to radio frequency
electromagnetic energy (EME):
*
The information provided in this document supersedes the general
safety information in user’s guides published prior to May 1, 2006
Legal and Safety
81
electrical, magnetic, and electromagnetic fields in the
radio frequency range between 9 kHz and 300 GHz.”
“Attachment to Resolution 303 from July 2, 2002."
When using your radio product as a traditional
two-way radio, hold the radio product in a
vertical position with the microphone one
to two inches (2.5 to 5 cm) away from the
lips
.
Operational Precautions
For optimal mobile device performance, and to be sure that human
exposure to RF energy does not exceed the guidelines set forth in
the relevant standards, always follow these instructions and
precautions.
If you wear the mobile device on your body,
always place the mobile device in a Motorola approved clip,
holder, holster, case or body harness. If you do not use a body-worn
accessory supplied or approved by Motorola and are not using the
mobile device in the intended use positions along side the head in
the phone mode or in front of the face in the two-way radio mode,
or if you hang your device from a lanyard around your neck, keep
the device at least 2.5 centimeters (1 inch) from your body when
transmitting.
Phone Operation
When placing or receiving a phone call, hold your mobile phone as
you would a landline telephone. Speak directly into the
microphone
.
Approved Accessories
For a list of approved Motorola accessories call 1-800-453-0920, or
visit our website at www.motorola.com/iden.
Two-way radio operation
Your radio product has been designed and tested to comply with
national and international standards and guidelines regarding
human exposure to RF electromagnetic energy, when operated in
the two-way mode (at the face, or at the abdomen when using an
audio accessory) at usage factors of up to 50% talk/50% listen.
RF Energy Interference/Compatibility
Nearly every electronic device is subject to RF energy interference
from external sources if inadequately shielded, designed or
otherwise configured for RF energy compatibility. In some
circumstances your mobile device may cause interference with
other devices.
Transmit no more than the rated duty factor of 50% of the time. To
transmit (talk), push the PTT button. To receive calls, release the
PTT button. Transmitting 50% of the time or less, is important
because this radio generates measurable RF energy only when
transmitting (in terms of measuring for standards compliance).
Legal and Safety
82
your mobile device with your implantable medical device, consult
your health care provider.
Follow Instructions to Avoid Interference
Problems
Turn OFF your mobile device in any location where posted notices
Hearing Aids
Some phones may interfere with some hearing aids. In the event of
such interference, you may want to consult your hearing aid
manufacturer or physician to discuss alternatives.
instruct you to do so.
In an aircraft, turn off your mobile device whenever instructed to
do so by airline staff. If your mobile device offers an airplane mode
or similar feature, consult airline staff about using it in flight.
Other Medical Devices and Health Care Facilities
Implantable Medical Devices
If you have an implantable medical devices, such as a pacemaker
or defibrillator, consult your physician before using this mobile
device.
Persons with implantable medical devices should observe the
following precautions:
If you use any other personal medical devices, consult your
physician or the manufacturer or your device to determine if it is
adequately shielded from RF energy. Turn off your radio product
when instructed to do so in hospitals or health care facilities that
may be using equipment that is sensitive to external RF energy.
Bluetooth
•
ALWAYS keep the mobile device more than 20
centimeters (8 inches) from the implantable medical
device when the phone is turned ON.
This device supports Bluetooth 1.2 including HSP, HFP, OPP, DUN,
PBAP, and BPP. In order for Bluetooth devices to communicate with
one another, they must utilize the same Bluetooth profile. To
determine the profiles supported by other Motorola devices, visit
www.hellomoto.com/bluetooth. For other devices, contact their
respective manufacturer.
•
•
DO NOT carry the mobile device in the breast pocket;
Use the ear opposite the implantable medical device to
minimize the potential for interference.
•
Turn OFF the mobile device immediately if you have any
reason to suspect that interference is taking place.
Certain Bluetooth features including those listed may not be
supported by all compatible Bluetooth-enabled devices, and/or the
functionality of such features may be limited in certain devices, or
by certain wireless carriers. Contact your wireless carrier about
feature availability and functionality.
Read and follow the directions from the manufacturer of your
implantable medical device. If you have any questions about using
Legal and Safety
83
Caring for the Environment by
Recycling
Driving Precautions
The use of wireless phones while driving may cause distraction.
Discontinue a call if you can’t concentrate on driving.
This symbol on a Motorola product means the
product should not be disposed of with household
waste.
Additionally, the use of wireless devices and their accessories may
be prohibited or restricted in certain areas. Always obey the laws
and regulations on the use of these products.
Disposal of your Mobile Device and Accessories
Responsible driving practices can be found in the “Smart Practices
Please do not dispose of mobile devices or electrical accessories
(such as chargers, headsets, or batteries) with your household
waste. These items should be disposed of in accordance with the
national collection and recycling schemes operated by your local or
regional authority. Alternatively, you may return unwanted mobile
devices and electrical accessories to any Motorola Approved
Service Center in your region. Details of Motorola approved
national recycling schemes, and further information on Motorola
recycling activities can be found at: www.motorola.com/recycling
Operational Warnings
Obey all posted signs when using Mobile devices in public areas.
Potentially Explosive Atmospheres
Areas with potentially explosive atmospheres are often but not
always posted, and can include fueling areas such as below decks
on boats, fuel or chemical transfer or storage facilities, or areas
where the air contains chemicals or particles, such as grain, dust
or metal powders.
Disposal of your Mobile Device Packaging and
User’s Guide
When you are in such area, turn off your handset, and do not
remove, install, or charge batteries unless it is a radio product type
especially qualified for use in such areas as “Intrinsically Safe” (for
example, Factory Mutual, CSA, or UL approved). In such areas,
sparks can occur and cause an explosion or fire.
Product packaging and user’s guides should only be disposed of in
accordance with national collection and recycling requirements.
Please contact your regional authorities for more details.
Legal and Safety
84
Symbol Key
Your battery, charger, or portable radio may contain symbols,
defined as follows:
Symbol
Definition
Listening at full volume to
music or voice through a
headset may damage your
hearing.
Symbol
Definition
032374o
Important safety information
follows.
Batteries and Chargers
Do not dispose of your battery
or phone in a fire.
Caution: Improper treatment or use of batteries may present
a danger of fire, explosion, leakage, or other hazard. For
more information, see the “Battery Use and Battery Safety”
section in this user’s guide.
Your battery or phone may
require recycling in
032375o
accordance with local laws.
Contact your local regulatory
authorities for more
Keep Your Mobile Device and Its Accessories
Away from Small Children
These products are not toys and may be hazardous to small
children. For example:
information.
Do not throw your battery or
phone in the trash.
•
•
A choking hazard may exist for small, detachable parts.
Improper use could result in loud sounds, possibly causing
hearing injury.
Your phone contains an
internal lithium ion battery.
Li Ion BATT
032378o
•
Improperly handled batteries could overheat and cause a
burn.
Do not let your battery,
charger, or phone get wet.
Glass Parts
Some parts of your mobile device may be made of glass. This glass
could break if the product is dropped on a hard surface or receives
Legal and Safety
85
a substantial impact. If glass breaks, do not touch or attempt to
remove. Stop using your mobile device until the glass is replaced
by a qualified service center.
•
•
•
Limit the amount of time you use headsets or headphones
at high volume.
Avoid turning up the volume to block out noisy
surroundings.
Seizures/Blackouts
Turn the volume down if you can’t hear people speaking
near you.
Some people may be susceptible to epileptic seizures or blackouts
when exposed to flashing lights, such as when playing video
games. These may occur even if a person has never had a previous
seizure or blackout.
If you experience hearing discomfort, including the sensation of
pressure or fullness in your ears, ringing in your ears, or muffled
speech, you should stop listening to the device through your
headset or headphones and have your hearing checked.
If you have experienced seizures or blackouts, or if you have a
family history of such occurrences, please consult with your
physician before playing video games or enabling a flashing-lights
feature (if available) on your mobile device.
For more information about hearing, see our Web site at
direct.motorola.com/hellomoto/nss/AcousticSafety.asp
(in English only).
Discontinue use and consult a physician if any of the following
symptoms occur: convulsion, eye or muscle twitching, loss of
awareness, involuntary movements, or disorientation. It is always
a good idea to hold the screen away from your eyes, leave the
lights on in the room, take a 15-minute break every hour, and stop
use if you are very tired.
Repetitive Motion
When you repetitively perform actions such as pressing keys or
entering finger-written characters, you may experience occasional
discomfort in your hands, arms, shoulders, neck, or other parts of
your body. If you continue to have discomfort during or after such
use, stop use and see a physician.
Caution About High Volume Usage
Warning: Warning: Exposure to loud noise from any
source for extended periods of time may affect your
hearing. The louder the volume sound level, the
Service and Repairs
If you have questions or need assistance, we’re here to help.
less time is required before your hearing could be
affected. To protect your hearing:
Go to www.motorola.com/support, where you can select from
a number of customer care options. You can also contact the
Motorola Customer Support Center at 1 (800) 453-0920 (United
Legal and Safety
86
States), 1 (877) 483-2840 (TTY, TDD United States for hearing
impaired).
•
•
Don’t allow the battery to touch metal objects. If
metal objects, such as jewelry, stay in prolonged contact
with the battery contact points, the battery could become
very hot.
Export Law Assurances
Don’t place your battery near a heat source.
Excessive heat can damage the phone or the battery. High
temperatures can cause the battery to swell, leak, or
malfunction. Therefore:
This product is controlled under the export regulations of the
United States of America and Canada. The Governments of the
United States of America and Canada may restrict the exportation
or re-exportation of this product to certain destinations. For further
information contact the U.S. Department of Commerce or the
Canadian Department of Foreign Affairs and International Trade.
•
•
Do not dry a wet or damp battery with an appliance or
heat source, such as a hair dryer or microwave oven.
Avoid leaving your phone in your car in high temperatures.
DOs
Battery Use and Safety
Important: Handle and store batteries properly to avoid
injury or damage. Most battery issues arise from improper
handling of batteries, and particularly from the continued use of
damaged batteries.
•
Do avoid dropping the battery or phone. Dropping
these items, especially on a hard surface, can potentially
cause damage.
•
Do contact your service provider or Motorola if your
phone or battery has been damaged from dropping
or high temperatures.
DON’Ts
•
Don’t disassemble, crush, puncture, shred, or
otherwise attempt to change the form of your
battery.
Don’t let the phone or battery come in contact with
water. Water can get into the phone’s circuits, leading to
corrosion. If the phone and/or battery get wet, have them
checked by your carrier or contact Motorola, even if they
appear to be working properly.
Important: Use Motorola Original products for quality
assurance and safeguards. To aid consumers in identifying
authentic Motorola batteries from non-original or counterfeit
batteries (that may not have adequate safety protection), Motorola
provides holograms on its batteries. Consumers should confirm
that any battery they purchase has a “Motorola Original”
hologram.
•
Legal and Safety
87
Motorola recommends you always use Motorola-branded
batteries and chargers. Motorola mobile devices are designed
to work with Motorola batteries. If you see a message on your
display such as Invalid Battery or Unable to Charge, take the following
steps:
Disposal: Promptly dispose of used batteries in accordance with
local regulations. Contact your local recycling center or national
recycling organizations for more information on how to dispose of
batteries.
Warning: Never dispose of batteries in a fire because they may
explode.
•
•
•
•
Remove the battery and inspect it to confirm that it has a
“Motorola Original” hologram;
If there is no hologram, the battery is not a Motorola
battery;
Battery Charging
Notes for charging your phone’s battery:
If there is a hologram, replace the battery and retry
charging it;
•
When charging your battery, keep it near room
temperature. Never expose batteries to temperatures
below 0°C (32°F) or above 45°C (113°F) when charging.
If the message remains, contact a Motorola authorized
service center.
•
•
New batteries are not fully charged.
Important: Motorola’s warranty does not cover damage to the
phone caused by non-Motorola batteries and/or chargers.
New batteries or batteries stored for a long time may take
more time to charge.
Warning: Use of a non-Motorola battery or charger may present a
risk of fire, explosion, leakage, or other hazard.
•
Motorola batteries and charging systems have circuitry
that protects the battery from damage from overcharging.
Proper and safe battery disposal and recycling: Proper
battery disposal is not only important for safety, it benefits the
environment. Consumers may recycle their used batteries in many
retail or service provider locations. Additional information on
proper disposal and recycling may be found on the Web:
Specific Absorption Rate
Your model wireless phone meets the governmental
requirements for exposure to radio waves.
Your mobile device is a radio transmitter and receiver. It is
designed and manufactured to not exceed limits for exposure to
radio frequency (RF) energy set by the Federal Communications
•
•
www.motorola.com/recycling
www.rbrc.org/call2recycle/ (in English only)
Legal and Safety
88
Commission (FCC) of the U.S. Government and by the Canadian
regulatory authorities. These limits are part of comprehensive
guidelines and establish permitted levels of RF energy for the
general population. The guidelines are based on standards that
were developed by independent scientific organizations through
periodic and thorough evaluation of scientific studies. The
standards include a substantial safety margin designed for the
safety of all persons, regardless of age or
submitted to the FCC and available for review by Industry Canada.
The highest SAR value for this mobile device when tested for use
at the ear is 1.17 W/kg, and when worn on the body, as described
in this guide, is 1.41 W/kg. Body-worn measurements can differ,
depending upon available accessories and regulatory
requirements. The SAR information includes the Motorola testing
protocol, assessment procedure, and measurement uncertainty
range for this product.
health, and to account for any variations in measurements.
While there may be differences between the SAR levels of various
mobile devices and at various positions, they meet the
governmental requirements for safe exposure. Please note that
improvements to this product model could cause differences in the
SAR value for later products; in all cases, products are designed to
be within the guidelines.
The exposure standard for mobile devices employs a unit of
measurement known as the Specific Absorption Rate (SAR). The
SAR limit set by the FCC and by the Canadian regulatory
authorities is 1.6 watts per kilogram (W/kg), averaged over one
gram of tissue. Tests for SAR are conducted using procedures
accepted by the FCC and by Industry Canada with the mobile
device transmitting at its highest certified power level in all tested
frequencies. Although the SAR is determined at the highest
certified power level, the actual SAR level of the mobile device
while operating can be below the maximum value. This is because
the mobile device is designed to operate at multiple power levels
so as to use only the power required to reach the network. In
general, the closer you are to a wireless base station, the lower
the power output.
Additional information on SAR can be found on the Cellular
Telecommunications & Internet Association (CTIA) Web site:
http://www.phonefacts.net
or the Canadian Wireless Telecommunications Association (CWTA)
Web site:
http://www.cwta.ca
AGPS and Emergency Calls
When you make an emergency call, your mobile device can use
Assisted Global Positioning System (AGPS) satellite signals to tell
the emergency response center your approximate location.
Before a mobile device is available for sale to the public in the U.S.
and Canada, it must be tested and certified to the FCC and Industry
Canada that it does not exceed the limit established by each
government for safe exposure. The tests are performed in
positions and locations (e.g., at the ear and worn on the body)
Legal and Safety
89
The AGPS feature has limitations, so always tell the emergency
response center your best knowledge of your location. Remain on
the phone for as long as the emergency response center instructs
you.
Motorola Limited Warranty for the
United States and Canada
What Does this Warranty Cover?
Note: FOR IDEN SUBSCRIBER PRODUCTS, ACCESSORIES
AND SOFTWARE PURCHASED IN THE UNITED STATES OR
CANADA
AGPS might not work for emergency calls, if your local
emergency response center does not process AGPS location
information. For details, contact your local authorities.
If your mobile device cannot find strong AGPS satellite signals, the
location of the nearest cell tower in contact with your mobile
device is automatically provided to the emergency response
center.
Subject to the exclusions contained below, Motorola, Inc. warrants
its Motorola iDEN Digital Mobile and Portable Handsets
("Products"), Motorola-branded or certified accessories sold for
use with these Products ("Accessories") and Motorola software
contained on CD-Roms or other tangible media and sold for use
with these Products ("Software") to be free from defects in
materials and workmanship under normal consumer usage for the
period(s) outlined below. This limited warranty is a
consumer's exclusive remedy, and applies as follows to
new Products, Accessories and Software purchased by
consumers in the United States or Canada, which are
accompanied by this written warranty:
AGPS Performance Tips
•
Go outside and away from underground locations, covered
vehicles, structures with metal or concrete roofs, tall
buildings, and foliage. Indoor performance might improve
if you move closer to windows, but some window sun
shielding films can block satellite signals.
•
Move away from radios, entertainment equipment, and
other electronic devices that might interfere with or block
AGPS satellite signals.
Products Covered
Length of Coverage
AGPS uses satellites controlled by the U.S. government and
subject to changes implemented in accordance with the
Department of Defense AGPS user policy and the Federal Radio
Navigation Plan. These changes might affect AGPS performance.
Products as defined
above.
One (1) year from the date of
purchase by the first consumer
purchaser of the product.
Legal and Safety
90
Batteries. Only batteries whose fully charged capacity falls below
80% of their rated capacity and batteries that leak are covered by
this limited warranty.
Products Covered
Length of Coverage
Accessories as
defined above.
One (1) year from the date of
purchase by the first consumer
purchaser of the product.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or neglect,
such as physical damage (cracks, scratches, etc.) to the surface of
the product resulting from misuse; (b) contact with liquid, water,
rain, extreme humidity or heavy perspiration, sand, dirt or the like,
extreme heat, or food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or Accessory to
abnormal usage or conditions; or (d) other acts which are not the
fault of Motorola, are excluded from coverage.
Products or
The balance of the original
warranty or for ninety (90) days
from the date returned to the
consumer, whichever is longer.
Accessories that are
Repaired or
Replaced.
Software as defined
above. Applies only to
physical defects in the
media that embodies
the copy of the software
(e.g. CD-ROM, or floppy
disk).
Ninety (90) days from the date
of purchase.
Use of Non-Motorola Products and Accessories. Defects or
damage that result from the use of Non-Motorola branded or
certified Products, Accessories, Software or other peripheral
equipment are excluded from coverage.
Unauthorized Service or Modification. Defects or damages
resulting from service, testing, adjustment, installation,
maintenance, alteration, including without limitation, software
changes, or modification in any way by someone other than
Motorola, or its authorized service centers, are excluded from
coverage.
What is not covered? (Exclusions)
Normal Wear and Tear. Periodic maintenance, repair and
replacement of parts due to normal wear and tear are excluded
from coverage.
Ornamental Decorations. Ornamental decorations such as
emblems, graphics, rhinestones, jewels, gemstones and their
settings, and other decorative elements, are excluded from
coverage.
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of tampering;
(c) mismatched board serial numbers; or (d) nonconforming or
Legal and Safety
91
non-Motorola housings, antennas, or parts, are excluded from
coverage.
How to Obtain Warranty Service or Other Information? To
obtain service or information, please call:
Communication Services. Defects, damages, or the failure of
Products, Accessories or Software due to any communication
service or signal you may subscribe to or use with the Products,
Accessories or Software is excluded from coverage.
Motorola iDEN Customer Services 1-800-453-0920 or
954-723-4910
TTY-877-483-2840
Or visit us online at http://www.motorola.com/iden
Software Embodied in Physical Media. No warranty is made
that the software will meet your requirements or will work in
combination with any hardware or software applications provided
by third parties, that the operation of the software products will be
uninterrupted or error free, or that all defects in the software
products will be corrected.
You will receive instructions on how to ship the Products,
Accessories or Software, at your expense, to a Motorola
Authorized Repair Center. To obtain service, you must include: (a) a
copy of your receipt, bill of sale or other comparable proof of
purchase; (b) a written description of the problem; (c) the name of
your service provider, if applicable; (d) the name and location of the
installation facility (if applicable) and, most importantly; (e) your
address and telephone number.
Software NOT Embodied in Physical Media. Software that is
not embodied in physical media (e.g. software that is downloaded
from the internet), is provided "as is" and without warranty.
What Other Limitations Are There? ANY IMPLIED
Who is covered? This warranty extends only to the first
consumer purchaser, and is not transferable.
WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR,
What will Motorola Do? Motorola, at its option, will at no
charge repair, replace or refund the purchase price of any Products,
Accessories or Software that does not conform to this warranty.
We may use functionally equivalent
reconditioned/refurbished/pre-owned or new Products,
Accessories or parts. No data, software or applications added to
your Product, Accessory or Software, including but not limited to
personal contacts, games and ringer tones, will be reinstalled. To
avoid losing such data, software and applications please create a
back up prior to requesting service.
REPLACEMENT, OR REFUND AS PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE
CONSUMER, AND IS PROVIDED IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OF IMPLIED. IN NO EVENT SHALL
MOTOROLA BE LIABLE, WHETHER IN CONTRACT OR TORT
(INCLUDING NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT, ACCESSORY OR SOFTWARE,
OR FOR ANY INDIRECT, INCIDENTAL, SPECIAL OR
Legal and Safety
92
CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS OF
REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF
INFORMATION OR DATA, SOFTWARE OR APPLICATIONS OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS,
ACCESSORIES OR SOFTWARE TO THE FULL EXTENT THESE
DAMAGES MAY BE DISCLAIMED BY LAW.
against the end user purchaser in any such suit which are
attributable to any such claim, but such defense and payments are
conditioned on the following:
a.That MOTOROLA will be notified promptly in writing by such
purchaser of any notice of such claim;
b.That MOTOROLA will have sole control of the defense of
such suit and all negotiations for its settlement or
compromise; and
Some states and jurisdictions do not allow the limitation or
exclusion of incidental or consequential damages, or limitation on
the length of an implied warranty, so the above limitations or
exclusions may not apply to you. This warranty gives you specific
legal rights, and you may also have other rights that vary from
state to state or from one jurisdiction to another.
c.Should the Product or parts become, or in MOTOROLA'S opinion
be likely to become, the subject of a claim of infringement of a
United States patent, that such purchaser will permit MOTOROLA,
at its option and expense, either to procure for such purchaser the
right to continue using the Product or parts or to replace or modify
the same so that it becomes non-infringing or to grant such
purchaser a credit for the Product or parts as depreciated and
accept its return. The depreciation will be an equal amount per
year over the lifetime of the Product or parts as established by
MOTOROLA.
Laws in the United States and other countries preserve for
Motorola certain exclusive rights for copyrighted Motorola
software such as the exclusive rights to reproduce and distribute
copies of the Motorola software. Motorola software may only be
copied into, used in, and redistributed with, the Products
associated with such Motorola software. No other use, including
without limitation disassembly of such Motorola software or
exercise of the exclusive rights reserved for Motorola, is
permitted.
MOTOROLA will have no liability with respect to any claim of
patent infringement which is based upon the combination of the
Product or parts furnished hereunder with software, apparatus or
devices not furnished by MOTOROLA, nor will MOTOROLA have
any liability for the use of ancillary equipment or software not
furnished by MOTOROLA which is attached to or used in
connection with the Product or any parts thereof.
Patent and Software Provisions
MOTOROLA will defend, at its own expense, any suit brought
against the end user purchaser to the extent that it is based on a
claim that the Product or parts infringe a United States patent, and
Motorola will pay those costs and damages finally awarded
Laws in the United States and other countries preserve for
MOTOROLA certain exclusive rights for copyrighted MOTOROLA
Legal and Safety
93
software, such as the exclusive rights to reproduce in copies and
distribute copies of such MOTOROLA software. MOTOROLA
software may be used in only the Product in which the software
was originally embodied and such software in such Product may
not be replaced, copied, distributed, modified in any way, or used
to produce any derivative thereof. No other use including, without
limitation, alteration, modification, reproduction, distribution, or
reverse engineering of such MOTOROLA software or exercise or
rights in such MOTOROLA software is permitted. No license is
granted by implication, estoppel or otherwise under MOTOROLA
patent rights or copyrights.
phones have been rated. Phones that are rated have the rating on
their box or a label on the box.
The ratings are not guarantees. Results will vary depending on the
user’s hearing device and hearing loss. If your hearing device
happens to be vulnerable to interference, you may not be able to
use a rated phone successfully. Trying out the phone with your
hearing device is the best way to evaluate it for your personal
needs.
M-Ratings: Phones rated M3 or M4 meet FCC requirements and
are likely to generate less interference to hearing devices than
phones that are not labeled. M4 is the better/higher of the two
ratings.
Hearing Aid Compatibility With Mobile
Phones
Some Motorola phones are measured for compatibility with
hearing aids. If the box for your particular model has “Rated for
Hearing Aids” printed on it, the following explanation applies.
When some mobile phones are used near some hearing devices
(hearing aids and cochlear implants), users may detect a buzzing,
humming, or whining noise. Some hearing devices are more
immune than others to this interference noise, and phones also
vary in the amount of interference they generate.
T-Ratings: Phones rated T3 or T4 meet FCC requirements and are
likely to be more usable with a hearing device’s telecoil (“T
Switch” or “Telephone Switch”) than unrated phones. T4 is the
better/higher of the two ratings. (Note that not all hearing devices
have telecoils in them.)
Hearing devices may also be measured for immunity to this type of
interference. Your hearing device manufacturer or hearing health
professional may help you find results for your hearing device. The
more immune your hearing aid is, the less likely you are to
experience interference noise from mobile phones.
The wireless telephone industry has developed ratings for some of
their mobile phones, to assist hearing device users in finding
phones that may be compatible with their hearing devices. Not all
Legal and Safety
94
Information From the World Health
Organization
Present scientific information does not indicate the need for any
special precautions for the use of mobile phones. If you are
concerned, you may want to limit your own or your children’s RF
exposure by limiting the length of calls or by using hands-free
devices to keep mobile phones away from your head and body.
Wireless: The New Recyclable
Your wireless phone can be recycled. Recycling your phone
reduces the amount of waste disposed in landfills and allows
recycled materials to be incorporated into new products.
The Cellular Telecommunications Industry Association (CTIA) and
its members encourage consumers to recycle their phones and
have taken steps to promote the collection and environmentally
sound recycling of end-of-life devices.
Source: WHO Fact Sheet 193
As a phone user, you have an important role in ensuring that this
device is recycled properly. When it comes time to give this phone
up or trade it in for a new one, please remember that the phone,
the charger, and many of its accessories can be recycled. It's easy.
To learn more about CTIA's Recycling Program for Used Wireless
Devices, please visit us at:
Further information: http://www.who.int./peh-emf
.
Product Registration
Online Product Registration:
www.motorola.com/us/productregistration
http://recycling.motorola.young-america.com/ index.html
Product registration is an important step toward enjoying your new
Motorola product. Registering permits us to contact you for
product or software updates and allows you to subscribe to
updates on new products or special promotions. Registration is not
required for warranty coverage.
California Perchlorate Label
Some mobile phones use an internal, permanent backup battery on
the printed circuit board that may contain very small amounts of
perchlorate. In such cases, California law requires the following
label:
Perchlorate Material - special handling may apply. See
www.dtsc.ca.gov/hazardouswaste/perchlorate
There is no special handling required by consumers.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola Personal Communications
Product you will need to provide a copy of your dated sales receipt
to confirm warranty status.
.
Thank you for choosing a Motorola product.
Legal and Safety
95
manner to the extent allowed by law. Furthermore, the purchase of
Motorola products shall not be deemed to grant either directly or
by implication, estoppel, or otherwise, any license under the
copyrights, patents, or patent applications of Motorola or any third
party software provider, except for the normal, non-exclusive,
royalty-free license to use that arises by operation of law in the
sale of a product.
Patent and Trademark Information
MOTOROLA, the Stylized M Logo and all other trademarks
indicated as such herein are trademarks of Motorola, Inc. ® Reg.
U.S. Pat. & Tm. Off. © 2009 Motorola, Inc. All rights reserved.
Microsoft and Microsoft Internet Explorer are registered
trademarks of Microsoft Corporation.
T9 is a trademark owned by Tegic Communications.
T9®Text Input Patent and Trademark Information.
Privacy and Data Security
Motorola understands that privacy and data security are important
to everyone. Because some features of your mobile device may
affect your privacy or data security, please follow these
This product is covered by U.S. Pat. 5,818,437, U.S. Pat. 5,953,541,
U.S. Pat. 6,011,554 and other patents pending.
Java and all other Java-based marks are trademarks or registered
trademarks of Sun Microsystems, Inc. in the U.S. and other
countries.
recommendations to enhance protection of your information:
•
•
•
Monitor access—Keep your mobile device with you and
do not leave it where others may have unmonitored
access. Lock your device’s keypad where this feature is
available.
All other product names or services mentioned in this manual are
the property of their respective trademark owners.
Keep software up to date—If Motorola or a
software/application vendor releases a patch or software
fix for your mobile device that updates the device’s
security, install it as soon as possible.
Software Copyright Notice
Motorola products may include copyrighted Motorola and third
party software stored in semiconductor memories or other media.
Laws in the United States and other countries preserve for
Motorola and third party software providers certain exclusive
rights for copyrighted software, such as the exclusive rights to
distribute or reproduce the copyrighted software. Accordingly, any
copyrighted software contained in the Motorola products may not
be modified, reverse-engineered, distributed, or reproduced in any
Erase before recycling—Delete personal information
or data from your mobile device prior to disposing of it or
turning it in for recycling. For instructions on how to delete
all personal information from your device, please contact
your local service provider.
Legal and Safety
96
•
Understanding AGPS—To provide location information
for emergency calls, certain Motorola mobile devices
incorporate Assisted Global Positioning System (AGPS)
technology. AGPS technology also can be used in
non-emergency applications to track and monitor a user’s
location—for example, to provide driving directions. Users
who prefer not to permit such tracking and monitoring
should avoid using such applications.
•
•
Get to know your Motorola mobile device and its
features such as speed dial and redial. If available,
these features help you to place your call without taking
your attention off the road.
When available, use a handsfree
device. If possible, add an additional
layer of convenience to your phone with
one of the many Motorola Original
handsfree accessories available today.
If you have further questions regarding how the use of your mobile
device may impact your privacy or data security, please contact
provider.
•
Position your mobile device within easy reach. Be
able to access your phone without removing your eyes
from the road. If you receive an incoming call at an
inconvenient time, if possible, let your voice mail answer
it for you.
Smart Practices While Driving
Drive Safe, Call Smart SM
•
•
•
Let the person you are speaking with know you are
driving; if necessary, suspend the call in heavy
traffic or hazardous weather conditions. Rain, sleet,
snow, ice, and even heavy traffic can be hazardous.
Check the laws and regulations on the use of phones and
their accessories in the areas where you drive. Always
obey them. The use of these devices may be prohibited or
restricted in certain areas—for example handsfree use
only. Go to www.motorola.com/callsmart (in English only)
for more information.
Your mobile device lets you communicate by voice and
data—almost anywhere, anytime, wherever wireless service is
available and safe conditions allow. When driving a car, driving is
your first responsibility. If you choose to use your phone while
driving, remember the following tips:
Do not take notes or look up phone numbers while
driving. Jotting down a “to do” list or going through your
address book takes attention away from your primary
responsibility, driving safely.
Dial sensibly and assess the traffic; if possible,
place calls when your car is not moving or before
pulling into traffic. If you must make a call while
moving, dial only a few numbers, check the road and your
mirrors, then continue.
Legal and Safety
97
•
Do not engage in stressful or emotional
conversations that may be distracting. Make people
you are talking with aware you are driving and suspend
conversations that can divert your attention away from the
road.
•
•
Use your mobile device to call for help. Dial 911 or
other local emergency number in the case of fire, traffic
accident, or medical emergencies (wherever wireless
phone service is available).
Use your mobile device to help others in
emergencies. If you see an auto accident, crime in
progress, or other serious emergency where lives are in
danger, call 911 or other local emergency number
(wherever wireless phone service is available), as you
would want others to do for you.
•
Call roadside assistance or a special
non-emergency wireless assistance number when
necessary. If you see a broken-down vehicle posing no
serious hazard, a broken traffic signal, a minor traffic
accident where no one appears injured, or a vehicle you
know to be stolen, call roadside assistance or other
special non-emergency wireless number (wherever
wireless phone service is available).
Legal and Safety
98
drafts
see also text messages,
messages
H
modem
using your handset as a
E
I
N
L
F
O
frequently asked questions
M
message center
G
P
GPS enabled
index
100
private calls
S
T
safety
Talk Around
private Talk Around calls
R
ring tones
switching to network
index
101
W
Y
V
index
102
|