Professional Dual CD Player
C.504
User Manual
13 Unplug this apparatus during lightning storms or when unused for long periods of time.
14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed
to rain or moisture, does not operate normally, or has been dropped.
- Do not expose this apparatus to drips or splashes.
- Do not place any objects filled with liquids, such as vases, on the apparatus.
- Do not install this apparatus in a confined space such as a book case or similar unit.
- The apparatus draws nominal non-operating power from the AC outlet with its POWER switch in the off position.
TABLE OF CONTENTS
1.
Functions and Controls (Layout)
1-1. Main Unit (Front Panel)
1-2. Main Unit (Rear Panel)
1-3. Remote Controller (Front Panel)
1-4. Remote Controller (Bottom Panel)
1-5. LCD
2. Standard Operation
2-1. CUE
2-2. MEMORY/CUE
2-3. Flash Start
2-4. Looping
2-5. Adjusting the tempo
2-6. Pitch Bending
2-7. KEY LOCK
2-8. PITCH LOCK
2-9. BPM/TAP
3. Advanced Operation
3-1. Effects
3-2. KEY SHIFT
3-3. BRAKE
3-4. VINYL
3-5. Reverse Play (REV)
3-6. Sampler
3-7. Track Memory
3-8. Fader Start
3-9. Relay Play
3-10. Auto Cue
3-11. Program Play
3-12. MP3 File Playback
3-13. Preset Menu
3-14. Back Up Memory
4. Specifications
5. Error Messages (Troubleshooting)
FUNCTIONS & CONTROLS
1-
1. Main Unit (Front Panel)
1. Disc Trays
Insert CD into these trays, label side upwards.
NOTE:
The C.504 reads Audio & MP3s from CDs & CD-Rs. + Audio Only CD-RWs
2. Tray LEDs
When power is turned on, these two LEDs will light.
3. OPEN/CLOSE Buttons
Open and close the appropriate disc tray. To avoid mistakes direct mode is off by default, therefore
the CDs cannot be ejected when in Play mode.
NOTE:
Direct Mode allows the CD to eject regardless of play / status (see Preset Menu)
4. POWER switch
Turns the power on and off. The tray LEDs light blue when power is supplied.
When the Timer Start function is on, playback begins when power is supplied.
1-2. Main Unit (Rear Panel)
5. OUTPUT jacks (RCA, unbalanced)
RCA connectors providing line level output signals, one set each for discs 1 and 2.
Maximum output level is +6dBV (2Vrms)
6. DIGITAL OUTPUT jacks (COAXIAL, S/PDIF)
Coaxial connectors provide S/PDIF digital output signals. These connectors can output the 44.1KHz
digital signals constantly even if pitch control is activated.
7. FADER START jacks
The C.504 can be controlled using the external Fader start command through these jacks. Connect
the mixer which supports the fader start function with appropriate 1/8” Fader Start cable as well as
audio signal. (TIP: Start, GND: back cue)
NOTE: When using the fader start function, connect the audio signal with the mixer as well. Also,
two 1/8” fader start cables are supplied in this unit.
8. AUX connectors (not included)
This jack is for future expansion capabilities.
9. REMOTE connector
Use this included connector to connect the remote controller to the main unit.
WARNNING
* DO NOT use any cable except the cable supplied with the C.504.
* Connect the cable in the way shown on the illustration on the rear panel of the C.504. If you con-
nect the cable in any other way, you may damage the C.504.
1-3. Remote Controller (Front Panel)
10. SEARCH Buttons
Search within the track selected, either forward >> or backward << with these buttons. When unit is
pausing, pressing this button shortly moves the start / cue point in 1 frame steps.
11. SELECT Buttons
Use these to perform track searches (next / previous) track. Search from track to track, either for-
ward (up arrow) or backward (down arrow) with these buttons.
12. SHIFT Button
The SHIFT button is a modifier button. Any button outlined with a silver border or box has a shift func-
tion / feature. This feature is written above or below the button itself. Holding SHIFT while pressing
another button performs the following functions:
SHIFT + OPEN/CLOSE
= [RESET]: Clears the all track memories and initializes the preset menu.
SHIFT + CTN/SGL
= [PROGRAM]:
Enters the program edit mode and program play mode.
SHIFT + TEMPO/BPM
= [FX RANGE]:
Selects the effect beat parameter (after an effect is selected).
Selects the parameter display mode and enters the track memory recall
SHIFT + TIME/ENTER
= [RECALL DISPLAY]:
mode.
SHIFT + PITCH RANGE
= [BANK]: Selects the memory bank for the track memory (A-E).
SHIFT + MEMORY/CUE
= [MEMO INS]:
Enters the track memory store mode.
SHIFT + SAMPLE
= [O— / O—O]:
Selects the sampler play mode a.k.a. Loop Mode. (single sample / con-
tinuous loop sample)
SHIFT + LOOP
= [REPEAT DEL]:
Selects the repeat play mode and deletes tracks while in memory mode.
Toggles the RELAY PLAY function on and off.
SHIFT + PLAY/PAUSE
= [RELAY PLAY]:
SHIFT + CUE
= [AUTO CUE]:
Toggles the AUTO CUE function on and off.
Enters preset menu mode.
SHIFT + JOG:
For more information on SHIFT functions read below and see advanced operation.
13. OPEN/CLOSE [RESET] Button
Opens and closes the appropriate tray. When DIRECT mode is off (in preset menu) and disc is being
played back, these buttons cannot be used.
Pressing and holding the SHIFT button then pressing this button clears all track memories and ini-
tializes the preset menu.
14. LCD
Displays visual feedback for C.504 functions.
15. CTN/SGL [PROGRAM] Button
Selects the play mode, either continuous or single mode.
Pressing and holding the SHIFT button then pressing this button enters the program edit mode and
program play mode.
When unit is in single play mode, “SGL” indicator in the LCD will light.
When unit is in program play mode, “PGM” indicator in the LCD will light.
16. TEMPO/BPM [FX RANGE] Button
Changes the mode of parameter display in the LCD between BPM (AUTO BPM or TAP BPM) dis-
play mode and current selected mode.
Pressing and holding the SHIFT button then pressing this button changes the effect beat parameter
directly when an effect is active. The Beat parameters are shown in the parameter display (on LCD).
NOTE::
FX RANGE parameters can only be selected after selecting the effect.
17. TIME/ENTER [RECALL DISPLAY] Button
Changes the time mode between elapsed time and remain time. When time mode is set to remain,
“REMAIN” indicator in the LCD will light.
When in preset mode, pressing this button confirms the current setting.
Pressing and holding the SHIFT button then pressing this button selects the mode of parameter dis-
play in the LCD from TEMPO, KEY, TAP, BPM, DIR, and track memory recall function.
18. PITCH RANGE [BANK] Button
Selects the pitch range from +/-4, 8, 16, 32, and 100%. The selected pitch range is momentarily dis-
played in the parameter section of the LCD screen.
Pressing and holding the SHIFT button then pressing this button selects the memory bank for track
memory. The selected bank (A-E) will light in the LCD.
19. VINYL Button
Turns the vinyl mode (scratch play mode) on and off. When vinyl mode is turned on, this button will
light blue and scratching can be performed by using Jog wheel.
20. REV Button
Changes the playback direction between forward and backward. When this button lights blue, the
playback direction is backward (Reversed).
21. DELAY Button
Turns the DELAY effect on and off. When DELAY effect is turned on, this button will light blue and
delay time is controlled with Jog wheel.
22. FILTER Button
Turns on and off the FILTER effect. When FILTER effect is turned on, this button will light blue. Filter
effect has two modes, manual filter and auto filter (pressing the FILTER button more than 1.5 sec-
onds changes the filter effect mode).
Manual Filter:
Filter frequency can be controlled with Jog wheel (default).
Auto Filter:Filter frequency is moved automatically and filter time can be controlled with Jog wheel.
When auto filter effect is turned on, time parameter is controlled with Jog wheel.
23. FLANGE Button
Turns on and off the FLANGER effect. When FLANGER effect is turned on, this button will light blue
and FLANGER time is controlled with Jog wheel.
FX NOTES:
Only one of these effects (DELAY, FILTER, or FLANGE) can be activated at a time.
If VINYL function is on, effect time and level cannot be controlled with Jog wheel (The priority is
scratching).
Once Delay, Filter, or Flange has been selected it is easier to enjoy FX with AUTO SYNCH on. More
advanced users adjust the effect level or parameter manually; Press & hold SHIFT button + effect
name (DELAY, FILTER, or FLANGE) to shift / toggle between the effect’s parameter & effect level
(wet/dry), then use the Jog wheel to adjust.
24. KEY SHIFT Button
Turns the KEY SHIFT function on and off. When KEY SHIFT function is turned on, this button will
light blue. Pressing and holding this button then using the Jog wheel selects the Key Shift value.
When Key Shift value is set to other than 0% internally, KEY indicator in the LCD will light.
NOTE:
When KEY LOCK function is activated, KEY SHIFT function cannot be turned on.
NOTE:
Turning off KEY SHIFT does not return KEY to original value. This must be done manually by re-
adjusting KEY SHIFT to its original value (via Jog Wheel / Pitch Bend)
25. Jog wheel
The following functions can be controlled by using the Jog wheel:
* Pitch Bend
* VINYL / Scratch
* Brake time
* KEY SHIFT control
* Preset menus [SHIFT + Jog Wheel]
* Effect parameters
* Program edit
* Track memory number select
* Search (in Paused mode)
26. MEMORY/CUE [MEMO/INS] Button
Activates the three buttons below (1/IN, 2/OUT, and 3/RELOOP) ready for CUE mode. When these
three buttons are set to CUE mode, this button will light green, press again to SET cue for bank 1,
2, or 3. Pressing and holding the SHIFT then pressing MEMORY/CUE enters the track memory store
mode [MEMO/INS].
NOTE:
Memory store mode allows the user to store track memory in several banks (A – E). For more infor-
mation on memory store mode see section 3-4 Track Memory.
When unit is in program edit mode, pressing this button inserts a program track.
For more information on the insert function see section 3-8 Program Play.
27. SAMPLE [o—/o-o] Button
Activates the three buttons below (1/IN, 2/OUT, and 3/RELOOP) ready for SAMPLE mode. When
these three buttons are set to SAMPLE mode, this button and “SAMPLE” indicator in the LCD will
light. When sampler is playing, pressing this button stops the sample (and the button is not lit).
NOTE:
Pressing and holding the SHIFT then pressing SAMPLE changes the sampler playback mode (o—
/o-o) between single play (o—) and loop play (o-o). When sampler loop is engaged, “LOOP” indica-
tor in the LCD will light.
28. LOOP [REPEAT/DEL] Button
Enters the three buttons (1/IN, 2/OUT, and 3/RELOOP) ready for LOOP mode. When these three
buttons are set to LOOP mode, this button will light. When loop play is engaged, pressing this but-
ton exits the loop play. Pressing and holding SHIFT then pressing this LOOP changes the repeat
mode on or off. When repeat mode is set to single repeat, “SGL” and “RPT” indicators in the LCD
will light. When repeat mode is set to all repeat, only “RPT” indicator will light. When unit is in pro-
gram edit mode, pressing this button deletes a program (track).
29. 1/IN Button
30. 2/OUT Button
31. 3/RELOOP Button
These three buttons have the following three functions:
CUE mode:
Store the in CUE points or play them seamlessly.
SAMPLER mode: Create the IN & OUT points of a Sample, and play it.
LOOP mode:
Create the IN & OUT points of a Loop, and re-loop.
32. BRAKE Button
Turns the brake function on and off.
Pressing and holding this Button then using the Jog wheel adjusts the brake time.
33. AUTO SYNC Button
Turns the AUTO SYNC function on and off. When AUTO SYNC is activated, this button will light and
effect time is synchronized with current BPM and BEAT RANGE that is set.
34. BPM/TAP Button
Set the tempo in BPM by tapping this button. When you press this button, the parameter counter
mode momentarily changes to TAP BPM display mode. Pressing this button more than 1.5 seconds
erases the tapped BPM. Pressing and holding this button then using Jog wheel adjusts the BPM in
0.1% increments. When the unit recognizes the BPM, this button will flash synchronized with the
BPM.
40. Pitch Fader
Changes the playback pitch, according to the range set by PITCH RANGE button. When playback
pitch is set to 0% or PITCH LOCK is turned on, the LED will light.
1-4. Remote Controller (Bottom Panel)
41. REMOTE connector
Connect this to the REMOTE connector on the rear panel of the main unit.
WARRNING
* DO NOT use any cable except the cable supplied with the C.504.
* Connect the cable to the C.504 as shown on the illustration on the rear panel. If you con-
nect the cable in any other way, you may damage the C.504.
1-5. LCD
42. M indicator
If there is track memory data for the current selected track in the current selected memory bank, this
indicator lights.
43. TRACK indicator
Shows the current track selected / playing.
44. REMAIN indicator
When the time mode is set to time remaining mode, this indicator lights.
45. SGL indicator
When the play mode is set to single play, this indicator lights.
46. RPT indicator
When the play mode is set to either single repeat or all repeat play mode, this indicator lights.
47. PGM indicator
When the play mode is set to programmed play, this indicator lights.
48. MP3 indicator
When a MP3 CD-ROM disc is inserted, this indicator lights.
49. Time display
This section is used to show track number, time values or messages.
50. Memory bank indicators
Lights the current selected memory bank indicator.
51. A.CUE indicator
Lights when AUTO CUE function is turned on.
52. RELAY indicator
Lights when relay play is set to on.
53. SAMPLE indicator
Lights when BANK MODE is set to SAMPLER.
54. LOOP indicator
Lights when sampler loop play is engaged.
55. Time Address Bar
Shows the current play position relative to the currently selected track.
56. PAR indicator
Lights when parameter display shows the effect parameter.
57. TEMPO indicator
Lights when parameter display shows the TEMPO / PITCH value.
58. KEY indicator
Lights when parameter display shows the key value.
Lights when key value is set to other than 0 (zero).
59. Parameter display
Displays the various parameters.
60. TAP indicator
Lights when parameter display shows the tap value.
61. BPM indicator
Lights when parameter display shows the auto BPM value.
62. DIR indicator
When a MP3 CD-ROM disc is inserted, this indicator lights and parameter display shows the current
selected directory number.
63. KEY LOCK indicator
Lights when KEY LOCK function is activated.
PLAYBACK OPERATION
2-1. CUE
The C.504 will always memorize the last played start point as the main cue point. After play has
begun, pressing the CUE button re-locates the audio and plays it from that point. Although very
quick, the CUE button is not seamless.
NOTE:
You cannot create a new cue point with this button. To create a new cue point, simply find the desired
location and press PLAY. The last location when play was pressed is now the current the cue point.
This can be done with or without stutter mode (using jog wheel or search buttons).
Stutter play with the CUE Button
Once a CUE point has been created, the unit will play when this button is pressed, and enter pause
mode when CUE button is released. If the PLAY button is pressed during CUE playback, the unit will
go into normal play mode.
2-2. MEMORY/CUE
The C.504 can have three flash (seamless) cue points stored with the CUE 1-3 buttons. These other
cue points can be done “on-the-fly” (without pressing play or pausing the audio) or in stutter mode
(using the Jog Wheel or Search buttons)
To memorize the CUE 1-3 points
1. Press MEMORY/CUE button to enter the unit into MEMORY/CUE mode (if not already lit this but-
ton will light up green.
2. Find the desired point in audio where you want to create a CUE point.
3. Press the MEMORY/CUE button until the parameter display in LCD shows “SEt”.
4. Press the desired CUE button (1, 2, or 3) within 5 seconds to store the desired CUE point in that
bank.
NOTE:
When the bank buttons (1, 2, or 3) has a point stored the button lights up green. The stored cue point
cannot be erased but can be overwritten.
When the unit is paused, pressing the MEMORY/CUE button then pressing the bank button (1, 2, or
3) starts the unit automatically, and stores it as a cue point.
For three seconds after storing one of the cue points, you cannot store another cue point.
2-3. Flash Start (Seamless Cue)
The flash start (seamless cue) function can be performed with the CUE (1, 2, or 3) buttons. After
storing the point, pressing any of these buttons performs a flash start / seamless cue.
2-4. IN/OUT Looping
To store the LOOP points
NOTE:
The three buttons (1/IN, 2/OUT, and 3/RELOOP) are shared for MEMORY/CUE, SAMPLER, and
LOOP functions. Therefore, only one of these three functions (MEMORY/CUE, SAMPLER, or LOOP
function) can be used at a time. (i.e. loop cannot be used simultaneously with sample).
1. Press LOOP button to enter the unit into LOOP mode. LOOP button will light green.
2. Press the IN button while in play or in pause mode. The IN button will light and the OUT button
will start flashing.
3. Press the OUT button while in play or in pause mode. IN, OUT, and RELOOP buttons will all light.
If the loop end point is set when the unit is playing, the C.504 starts loop playback seamlessly. If
the loop end point is set when the unit is paused, the C.504 goes to the loop start point then paus-
es.
NOTE:
For “on-the-fly” looping, when playing desired song press IN to create start point, and OUT to cre-
ate end point, now the unit will seamlessly loop and seamlessly re-loop or stutter every time
RELOOP is pressed. Pressing IN or OUT while in LOOP mode will automatically overwrite any pre-
vious points set.
Disengage loop play
When loop play is engaged, pressing the LOOP button disengages loop play. In this case, the unit
continues normal playback and RELOOP button will start flashing, but the loop points are not erased.
When loop play is engaged, locating the unit to the out point of a loop section disengages loop play
(i.e. pressing the CUE button, etc…). At this time, the RELOOP button start flashing, but the loop
points are not erased.
Re-looping
When loop play is disengaged and loop points are already stored, pressing the RELOOP button
starts looped playback and the RELOOP button lights.
Seamless playback from the LOOP start point
Pressing the RELOOP button always play starts from the loop start point.
Changing the LOOP points
Loop start and end points cannot be erased but be over written. Execute the same way as Section
2-4: “IN/OUT Looping” to change the loop points.
2-5. Adjusting the tempo
Pitch range
The C.504 features +/-4, 8, 16, 32, and 100 of pitch control range. Pressing the PITCH RANGE but-
ton changes the pitch control range. The parameter display section of the LCD momentarily shows
the selected pitch range.
Using the Pitch slider
The pitch slider controls playback pitch in % increments. Pitch changes are displayed in the LCD.
The C.504 offers a +/- 4% range for more accurate adjustments when beat matching. At this setting
each marker (dot) is equal to 1%.
2-6. Pitch Bending
When playing back a disc, pressing the BEND + or - buttons, or using the Jog wheel can change
playback tempo momentary. Pressing the + button or moving the Jog wheel clockwise increases the
playback speed which returns to original speed when this button is released or the Jog wheel stops
moving. Pressing the - Button or moving the Jog wheel counterclockwise decreases the playback
speed and which also returns to original speed when released or the Jog wheel stops moving.
NOTE:
* When VINYL button or an effect button is not lit, the Jog wheel works for pitch bend function. The
maximum pitch bend range is 16% (for jog wheel & buttons).
* When PITCH LOCK function is activated, playback pitch is fixed.
2-7. KEY LOCK
When pitch range is set to +/-4, 8, or 16%, pressing the KEY LOCK button turns on and off the KEY
LOCK function. When KEY LOCK function is turned on, pitch control does not affect the actual Key
of the playback. For example you can adjust the speed (TEMPO/BPM) of a track without affecting
the harmonic Key. When the KEY LOCK function is turned on, “KEY LOCK” indicator shows in the
LCD screen.
NOTE:
If TEMPO range is set to +/-32% or 100%, the KEY LOCK function does not work.
2-8. PITCH LOCK
Pressing the Pitch LOCK button turns on and off the PITCH LOCK function. When PITCH LOCK
function is turned on, pitch control devices (such as Jog Wheel, Pitch Fader, and Pitch Bend but-
tons) are ineffective; the Pitch will remain “locked” at zero 0%, until deactivated.
NOTE:
When the PITCH LOCK function is turned on, parameter display shows “—-“ in the TEMPO / PITCH
section of the LCD screen.
2-9. Auto BPM and TAP Button
The C.504 features automatic BPM calculation and TAP (manual) BPM calculation. Set the param-
eter display mode to BPM by Pressing TEMPO/BPM. If the BPM has not been manually entered the
BPM is counted automatically and displayed in the parameter display. The BPM/TAP button blinks
in tempo. Pressing the BPM/TAP button repeatedly (suggested 8 times or more) enters the song
tempo (BPM) in manually. This manual BPM is shown in the LCD parameter display and the
BPM/TAP button blinks in tempo. The BPM displayed is affected by the pitch slider. If the pitch slid-
er is moved, the BPM will be changed automatically.
Pressing and holding the TAP button for more than 1.5 seconds erases the tapped BPM value. Also,
presing and holding the TAP button then moving the Jog wheel (within 1.5 seconds) adjusts the BPM
manually in 0.1 steps.
NOTE:
BPM is also used for the effect time or beat parameter. When you set the BPM using the TAP but-
ton, the manually entered (tapped) BPM will be used for the effect time or beat parameter. When
there is no tapped BPM (or you erase the tapped BPM), auto counted BPM will used for effect
parameter instead.
MORE ADVANCED OPERATIONS
3-1. Effects
The C.504 includes three effects, DELAY, FILTER, and FLANGER. Only one effect can be activated
at a time. Pressing one of the effect buttons can activate the effect, and light the button blue.
Pressing the AUTO SYNC button synchronizes the effect time with the BPM.
Pressing and holding the SHIFT button then pressing one of effects DELAY, FILTER, or FLANGER
can adjust the effect parameter or effect level (wet/dry) with the Jog wheel.
Effect time setting
When an effect is activated and AUTO SYNC function is off, using the Jog wheel can adjust the effect
time.
The effect time parameter is shown in the parameter display.
NOTE:
* When the scratch function turns on, the effect time cannot be controlled with the Jog wheel.
Synchronizing the effect time with the BPM
When an effect is activated and AUTO SYNC button is turned on (AUTO SYNC button lights blue),
using the Jog wheel or pressing and holding the SHIFT button then pressing the BPM button (BEAT
RANGE) can change the effect beat synchronized with the BPM. The effect beat parameter is
shown in the parameter display.
NOTE:
Another easy way to use effects is by using FX RANGE. Easily synchronize effects and toggle
through beat parameters by utilizing the FX RANGE button (Press and hold SHIFT + BPM = FX
RANGE). FX RANGE can only be used after an effect DELAY, FILTER, or FLANGER is selected.
Also, when scratch function is on (VINYL), the effect beat cannot be controlled with the Jog wheel.
Effect level setting (wet/dry)
When an effect is activated, pressing and holding the SHIFT button then pressing the activated effect
button enters the effect level setting mode. In this mode, using the Jog wheel can change the effect
level. The effect level parameter is shown in the parameter display.
DELAY
Pressing the DELAY button activates the Delay effect.
Effect time: 1msec to 3,500msec (default: 500msec)
Effect beat: 2, 1, 3/4, 1/2, 1/4 (default: 1)
Effect level: 0 to 100 (default: 50)
FILTER
Pressing the FILTER button activates the Low pass filter effect.
Effect time: 10msec to 16sec (default: 2sec)
Effect beat: 32, 16, 8, 4, 2, 1, 1/2 (default: 4)
Effect level: 0 to 100 (default: 50)
NOTE:
Filter effect has two operation modes, manual mode and auto mode.
In manual mode, filter frequency can be controlled with the Jog wheel.
In auto mode, filter frequency is moved automatically followed by BPM and effect beat parameter.
Pressing and holding the FILTER button more than 1.5 seconds changes the filter effect mode.
When filter effect mode is set to manual mode, you can move the filter frequency using with the Jog
wheel even if the scratch function is activated.
FLANGER
Pressing the FLANGE button activates the Flanger effect.
Effect time: 10msec to 16sec (default: 500msec)
Effect beat: 32, 16, 8, 4, 2, 1, 1/2 (default: 1)
Effect level: 0 to 100 (default: 50)
3-2. KEY Shift
When pitch range is set to +/-4, 8, or 16%, pressing the KEY SHIFT button turns on and off the KEY
SHIFT function. When KEY SHIFT function is turned on / backlight, the harmonic KEY can manual-
ly be adjusted independent of Pitch (via the Jog Wheel). For example you can adjust the harmonic
NOTE: (KEY) of a track without affecting the speed (TEMPO).
The C.504 features up to +/-16% KEY shift control.
KEY shift control range is determined with pitch range setting.
When pitch range is set to 4%, KEY shift value can be set in 0.05% steps.
When pitch range is set to 8%, KEY shift value can be set in 0.1% steps.
When pitch range is set to 16%, KEY shift value can be set in 0.2% steps.
When pitch range is set to 32%, or 100%, the KEY shift control function does not work.
Pressing and holding the KEY SHFT button then moving the Jog wheel sets the KEY value.
NOTE:
When the KEY LOCK function is activated, the KEY SHIFT function does not work (and vice versa).
The KEY shift value shown in LCD is a value combined with any changes made by using the slider
(Pitch Fader).
3-3. Brake
Brake function simulates the braking audio just like turning off an analog turntable. Pressing the
PLAY/PAUSE button while unit is playing performs the braking.
Pressing the PLAY/PAUSE button during the braking starts the music again with current tempo.
When brake function is activated, the BRAKE button lights blue.
Set the brake time
Pressing and holding the BRAKE button then using the Jog wheel adjusts the brake time. Brake time
can be set to 0.1 to 5 seconds in 0.1 sec. steps. Default brake time is 2.5 sec.
3-4. Vinyl
When the VINYL button is activated, scratching can be performed with the Jog wheel.
NOTE:
VINYL mode overrides most other play modes and effects*
For 3 seconds after the flash start with CUE 1, 2, 3 buttons, or cuing with CUE button, backward
direction of scratching cannot be performed
Backward direction of the scratching can be performed up to 7 seconds.
When VINYL function is on, the Jog wheel works as the search dial.
* When filter effect is activated with manual mode, VINYL mode cannot be performed with the Jog
wheel.
3-5. Reverse Play
The C.504 features the reverse play function. Pressing the REV button changes playback direction.
When playback is reversed, the REV button will light blue.
NOTE:
More than 3 seconds after pausing, reverse play cannot be performed.
In the reverse play mode, flash start, creating the looping, loop play, and auto cue functions do not
work.
However you can create a sample in reverse mode.
3-6. Sampler
The C.504 includes eight seconds sampler on each player (CD1=8sec./CD2=8sec.).
NOTE: the sample is played simultaneous to any other audio being played.
By default the sample is played back as a single sample, one time per activation.
Sampling
NOTE:
The three buttons (1/IN, 2/OUT, and 3/RELOOP) are shared for MEMORY/CUE, SAMPLER, and
LOOP functions. Therefore, only one of these three functions (MEMORY/CUE, SAMPLER, or LOOP
function) can be used at a time.
1. Press the SAMPLE button to enter the unit into SAMPLER mode. “SAMPLE” indicator in the LCD
will light.
2. Press the IN button when playing or pausing. IN Button will light and OUT button will start flash-
ing.
3. Press the OUT button when playing or pausing. Both IN and OUT buttons will light.
NOTE:
If less than eight seconds elapse, or if the end of the track is reached without pressing the OUT but-
ton, the end point of the sample will automatically be set to the end of track.
To Play the sample
When IN and OUT buttons are light, press the RELOOP button; this starts the sample from the
beginning.
To Stop the sample
When sample is playing, press the SAMPLE button or any other Bank Mode button (MEMORY/CUE
or LOOP) to stop the sampler.
Erasing the recorded sample and re-sampling
Recorded sample data cannot be erased but, it can be over written.
Follow the directions under “Sampling” to overwrite and re-sample.
Sampler Loop
Pressing and holding the SHIFT button then pressing the SAMPLE button turns the sampler loop
play on and off. When sampler loop play is activated, LOOP indicator will display in the LCD. O— is
a single sample played when RELOOP is pressed. O—O is a looped sample played when RELOOP
is pressed.
3-7. Track Memory
The C.504 can memorize the various playback settings of current selected tracks, up to 100 tracks
of memory in each of 5 banks (A to E) can be stored.
You could use each bank for a different user style / preference or use each bank for a different set-
ting for each track, for example.
To store the Track Memory Data
1. Select the memory bank [BANK] by pressing and holding the SHIFT button then pressing the
PITCH RANGE Button.
2. Enter the track memory mode [MEMO/INS] by pressing and holding the SHIFT button then press-
ing the MEMORY/CUE button.
3. LCD shows the lowest empty memory number.
4. Use the Jog wheel to change the memory number if necessary.
5. Press the TIME/ENTER button. At this time, if there is stored memory in the selected memory
number, “-SUrE-“ indication is displayed in the LCD.
Pressing the ENTER button overwrites the current track data in the selected memory number.
Pressing any other button cancels the storing operation.
Memorized data
* Disc ID
* CUE point
* CUE 1-3 points
* Repeat mode
* Tempo data
* Key Lock On/Off
* Brake On/Off
* Key Shift value
* Sampling points
* Loop points
* Play mode
* Tempo Range
* TAP value
* Brake Time
* Time mode
* Effect On/Off
NOTE:
* Sampling points for MP3 filter cannot be memorized.
To Recall the Track Memory Data
1. Select the appropriate memory bank [BANK] by pressing and holding the SHIFT button then
pressing the PITCH RANGE button. If there is memory data of a selected track(s) in the current
selected memory bank, the “M” indicator is displayed in the LCD screen.
2. Enter the recall mode by pressing and holding the SHIFT button then pressing the TIME/ENTER
button. If there is a track memory data for the current selected track, its memory number is shown
in the LCD.
3. When track memory number is shown in the LCD, pressing the ENTER button recalls the track
memory data.
The C.504 can recall the track (selection #) from the track memory data.
1. Select the memory bank [BANK] by pressing and holding the SHIFT button then pressing the
PITCH RANGE button. If there is a track memory data of selected track in the current selected
memory bank (A to E), the “M” indicator in the LCD lights.
2. Enter the recall mode [RECALL DISPLAY] by pressing and holding the SHIFT button then press-
ing the TIME/ENTER button. If there is a track memory data for the current selected track, its mem-
ory number is shown in the LCD. Use the Jog wheel to select the desired track memory number.
3. When the appropriate track memory number is shown in the LCD, pressing the ENTER button
recalls the track from the track memory number.
NOTE:
CUE 1-3 and loop points can be memorized and/or recalled. However, just after the recall opera-
tion, start from the CUE 1-3 or loop points will not be seamless when performed on the first try
(because there are no data in the RAM buffer just after the recall operation). Once playing from cue
points (CUE 1-3) and/or loop start point, flash start and/or looping can again be performed seam-
lessly.
3-8. Fader Start
Connect the Fader Start jack on the rear panel of the main unit and Fader Start jack on the external
device which supports the fader start function (for example RM-series mixers, SMX-401, SMX-211).
Use the Fader Start cable which is supplied to perform the fader start/back cue performance via
mixer’s crossfader. Check your mixer’s owner’s manual for verification of this feature
TIP:
Start (low active, more than 50ms)
GND:
Back cue (low active, more than 50ms)
NOTE:
When using this feature along with MP3 discs, the GND is not active and back cue is not operational.
3-9. Relay Play
Pressing and holding the SHIFT button then pressing the PLAY/PAUSE button [RELAY PLAY] turns
the relay play function on and off. When the relay play is turned on, the “RELAY” indicator is dis-
played in the LCD screen.
NOTE:
Turning on the Relay play function either control unit 1 or 2 turns on the relay play function. While
the relay play is activated, when unit 1 finishes playback, unit 2 will start playback automatically, and
vice versa.
3-10. Auto Cue
Auto cue function allows the unit to search the beginning of the song and pause there automatical-
ly. The detection level is fixed to -54dB. When Auto cue function is turned on, the “A.CUE” indicator
is displayed in the LCD screen.
Pressing and holding the SHIFT button then pressing the CUE button [AUTO CUE] turns the AUTO
CUE function on and off.
NOTE:
Default setting is ON.
3-11. Program Play
The C.504 features up to 30 tracks of program play function. Program memory itself is maintained
even if power is turned off; and if CD is not ejected, the program list will be backed up.
NOTE:
If the disc is ejected, program will be erased.
Once one of the CUE 1-3 buttons is pressed, programmed play will be cancelled.
Create the program
1. Enter the program edit mode [PROGRAM] by pressing and holding the SHIFT button then press-
ing the CNT/SGL button.
2. Program number is shown in the parameter display of LCD. Select the desired track with the track
select buttons.
3. Go to next program number by pressing the TIME/ENTER button or using the Jog wheel.
4. Repeat steps 2-3.
5. Exit the program edit mode [PROGRAM] by pressing and holding the SHIFT button then press-
ing the CNT/SGL button.
Edit program
1. Enter the program edit mode [PROGRAM] by pressing and holding the SHIFT button then press-
ing the CNT/SGL button.
2. Program number is shown in the parameter display. Select the desired program number with the
Jog wheel.
3. Select desired track with track skip buttons.
4. Repeat 2-3.
5. Exit the program edit mode [PROGRAM] by pressing and holding the SHIFT button then press-
ing the CNT/SGL button.
Insert program
1. Enter the program edit mode [PROGRAM] by pressing and holding the SHIFT button then press-
ing the CNT/SGL button.
2. Program number is shown in the parameter display. Select desired program number where you
want to insert the program with the Jog wheel.
3. Press MEMORY/CUE (INS) button.
4. Select desired track with track skip buttons.
5. Repeat 2-4.
6. Exit the program edit mode [PROGRAM] by pressing and holding the SHIFT button then press-
ing the CNT/SGL button.
Delete program
1. Enter the program edit mode [PROGRAM] by pressing and holding the SHIFT button then press-
ing the CNT/SGL button.
2. Program number is shown in the parameter display. Select desired program number that you
want to delete the program with the Jog wheel.
3. Press LOOP (DEL) button.
4. Repeat 2-3.
5. Exit the program edit mode [PROGRAM] by pressing and holding the SHIFT button then press-
ing the CNT/SGL button.
3-12. MP3 File Playback
The C.504 can play the MP3 file which is recorded as following specific format.*
Disc format:
ISO9660 Level 1
Number of directories:
Number of files:
File format:
up to 254
up to 255
MPEG 1 audio layer 3
32kbps to 320kbps, (192kbps recommended)
Bit rate:
Constant Bit Rate
Sampling frequency:
File extension:
44.1KHz, Stereo
mp3, Mp3, mP3, MP3
NOTE:
* If the disc is recorded with multi session way, the C.504 can read the files in first session area only.
* Variable bit rate (VBR) format is not supported.
Unfortunately MP3 playback function does not support following functions.
* CUE and CUE 1-3
* Flash start / Hot Cue
* Loop
* Search
* Reverse play
* Track memory
* Remain time display
* Time address bar display
NOTE:
Backward direction of the scratching can be performed up to 7 seconds.
Playing the MP3 file
1. Insert the CD-ROM which includes the MP3 files.
2. Pressing the TRACK SELECT button selects the MP3 file.
3. Press the PLAY/PAUSE button.
Pressing and holding the SHIFT button then pressing the TRACK SELECT button skips the directo-
ry.
NOTE:
Since the C.504 does not support the text display, the text information included in the ID tag is not
displayed. File number is shown in the TRACK number area and directory number is shown in the
parameter display. When parameter display shows the directory number, “DIR” is indicated in LCD
screen.
3-13. Preset Menu
1. Pressing and holding the SHIFT button then using the Jog wheel selects the preset menu.
2. Select the desired preset menu then press the TIME/ENTER button, the LCD shows the preset
menu and its parameter.
3. Set the desired parameter with the Jog wheel.
4. Pressing the TIME/ENTER button confirms the new parameter.
5. Pressing any other button exits the preset operation.
01 t PLAY
Timer Play OFF*, ON
Turns the “Power on play” on and off
02 dIrECt
Direct
When direct mode is set to on, disc can be ejected when disc is played, and when
insert the disc, playback is started automatically.
OFF*, ON
03 rEAd
TOC Read Mode
nor*, AUt
Selects the TOC read mode.
nor: Uses the previous servo value.
AUt: Adjust the servo value every time.
04 rECALL
Memory Auto Recall Mode nor*, AUt
Selects the track memory recall mode.
nor: Recall the track memory data when recall operation is done.
AUt: Recall the tempo setting, tempo range, KEY setting, Key lock setting, and
BPM value from track memory data when track is selected.
05 FAdEr
06 F PrE
Cd: Disc playback is started and stopped with the fader.
SAM: Controls the playback of the sampler.
COM: Controls a combination of disc and sampler playback.
Factory Preset - SUrE –
Initialize the preset menu.
07 ALLCLr
Memory All Clear
- SUrE –
Clear the all memorized data.
* Indicates Factory Default Setting
3-14. Back Up Memory
Each time you turn off the power, the status of following features are stored into backup memo-
ry.
* Time mode
* Play mode
* Brake on/off
* Brake Time
* Key Lock on/off
* Auto Cue on/off
* Relay Play on/off
* Pitch Range
* Memory Bank
* Preset Settings
* Program
* Effect on/off
* REVERSE on/off
SPECIFICATIONS
Disc type:
Number of channels:
Resolution:
8cm / 12cm CD
2-channel
16-bit
Sampling frequency:
Analog output:
Output impedance:
Maximum output level:
Digital output:
44.1kHz
RCA pin jack
<1kohm
+6dBV
Coaxial
Format:
S/PDIF
Voltage requirements
USA/Canada:
120V AC, 60Hz
230V AC, 50Hz
240V AC, 50Hz
30W
0.9A
E4
UK/Europe:
Australia:
Power consumption:
Peak inrush current:
Applicable electromagnetic environment:
Dimensions (W x H x D mm)
Main unit:
482 x 94 x 272
482 x 132 x 83
Remote control unit:
Weight
Main unit:
Remote control unit:
5.7kg
2.3kg
The following values are applicable when Key and Pitch (tempo) values are set to 0.
Frequency response:
Dynamic range:
20 - 20kHz, +0.5/-1.0dB
>95dB
S/N ratio:
>95dB
Total harmonic distortion:
<0.01% at 1kHz
ERROR MESSAGES & TROUBLESHOOTING
Error Messages occur when there is a known issue / problem with the playback device.
Below are the Error numbers, and explanation of the problem and how to correct it.
Err 01 TOC Read error - the disc’s Table of Contents cannot be read within 20 seconds - try with anoth-
er disc or remove and clean the existing disc before replacing it
Err 02 GFS error - GFS signal cannot be detected within five seconds - try with another disc or remove
and clean the existing disc before replacing it
Err 03 Focus error - after repeating the attempt eight times to focus, an error still occurs - try with
another disc or remove and clean the existing disc before replacing it
Err 04 Sub-Q error - the sub-Q code cannot be detected (twice within five seconds) - try with another
disc
Err 05 Loading error - the open or close operation cannot be completed, even after retries, or there is
an internal error - make sure that there are no obstructions preventing the tray’s operation
Err 06 Sled error - an internal drive error - try turning the power off, waiting a few seconds, and turn-
ing it on again
Err 07 Error in communication between decks - try turning the unit off, waiting a few seconds, and turn-
ing it on again
Err 10 S-DRAM error - an internal S-DRAM error - try turning the power off, waiting a few seconds,
and turning it on again
NOTE:
If any of the numbered error messages are repeated, try using another disc.
If the errors continue with a number of discs, turn the unit off, wait for a few seconds, and turn it on
again.
If the errors still continue or other error occurs, contact your local Stanton distributor for repair. A list of
The C.504 will enter SLEEP mode after 30 min. of inactivity. To conserve electricity and the LCD, the
screen will darken and may appear off; however the word SLEEP is partially visible. This is a normal
procedure when the unit is not in use, to exit sleep mode simply press CUE or any other button.
For additional user support on this and other Stanton products contact [email protected] or
WARRANTY & RETURN POLICY
Warranty
Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the
U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or provid-
ing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) follow-
ing the date of original purchase. Exceptions to this warranty are as noted below:
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier to occur of thirty (30) days
following the date of original purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000;
and Switches - 10,000.
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made
necessary by reason of misuse, alteration, normal wear, or accident are not covered under this warranty.
Returns
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requir-
ing warranty repair or replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton deal-
er from whom the merchandise was purchased and in the same country where the merchandise was purchased. For pur-
poses of purchases made via the Internet, the merchandise must be returned to the authorized Stanton dealer in the coun-
try where the authorized Stanton dealer which sold the merchandise to purchaser is located and not the authorized Stanton
dealer in the country where the purchaser is located or the country in which the merchandise was received. Any returns to
a non-authorized dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to
be sold or as set forth above will void this warranty.
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise,
and follow such authorized Stanton dealer’s return policy.
Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or applica-
tion made of the merchandise. Stanton’s liability for any claim, whether based on breach of contract, negligence, infringe-
ment of any rights of any party, or product liability, and relating to the merchandise shall not exceed the price received by
Stanton from your purchase of such merchandise. In no event will Stanton be liable for any special, incidental or conse-
quential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negli-
gence of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton disclaims
any express or implied warranties of merchantability or fitness for a particular purpose.
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to vari-
ation from state to state and country to country.
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above,
please include a written explanation with the merchandise when returned pursuant to the terms and conditions set forth
herein.
Stanton Magnetics, Inc, 3000 SW 42 St. Hollywood, Florida 33312.
ADDITIONAL SAFETY INFO
For U.S.A
TO THE USER
For the consumers in Europe
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accor-
dance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residental area is likely
to cause harmful interference in which case the user will
be required to correct the interference at his own
expense.
WARNING
This is a Class A product. In a domestic environment, this
product may cause radio interference in which case the
user may be required to take adequate measures.
Pour les utilisateurs en Europe
AVERTISSEMENT
Il s’agit d’un appareil de Classe A. Dans un environ-
nement domestique, cet appareil peut provoquer des
interférences radio. Dans ce cas, l’utilisateur peut être
amené à prendre des mesures appropriées.
Fur Kunden in Europa
Warnung
Dies is eine Einrichtung, welche die Funk-Entstörung
nach Klasse A besitzt. Diese Einrichtung kann im
Wohnbereich Funkstörungen versursachen ; in diesem
Fall kann vom Betrieber verlang werden, angemessene
Maßnahmen durchzführen und dafür aufzukommen.
CAUTION
Changes or modifications to this equipment not express-
ly approved by Stanton for compliance could void the
user's authority to operate this equipment.
This product has been designed and manufactured according to FDA
regulations "title 21, CFR, chapter 1, subchapter J, based on the
Radiation Control for Health and Safety Act of 1968", and is classified as
a class 1 laser product. There is no hazardous invisible laser radiation
during operation because invisible laser radiation emitted inside of this
product is completely confined in the protective housings.
Rack Mounting the Unit
The units should be mounted, using the supplied rack mounting kits. A
typical configuration is shown below, but other configurations are possi-
ble:
The label required in this regulation is shown 1
NOTE
Do not install this apparatus in a confined space such as a book case or
similar unit.
Optical pickup:
CAUTION
Type: KSS-213C
- DO NOT REMOVE THE PROTECTIVE HOUSING USING A SCREW-
DRIVER.
Manufacturer: SONY Corporation
Laser output: Less than 0.4 mW on the objective lens
Wavelength: 760 - 800 nm
- USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY
RESULT IN HAZARDOUS RADIATION EXPOSURE.
- IF THIS PRODUCT DEVELOPS TROUBLE, CONTACT YOUR NEAR-
EST QUALIFIED SERVICE PERSONNEL, AND DO NOT USE THE
PRODUCT IN ITS DAMAGED STATE.
|