Stanton C303 User Manual

CC..33OO33  
__________________________________________________________  
PROFESSIONAL TABLETOP CD PLAYER  
__________________________________________________________  
10.  
11.  
Polarization – This product may be equipped with a polarized alternation-current line plug (a plug having one blade wider than the other.)  
This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try  
reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose  
of the polarized plug.  
Power-Cord Protection – Power-supply cords should be routed so that they are not likely to be walked on or pinched by items place upon or  
against them, paying particular attention to the cord in correspondence of plugs, convenience receptacles, and the point where they exit from  
the appliance.  
12.  
13.  
Cleaning – The appliance should be cleaned only as recommended by the manufacturer. Clean by wiping with a slightly damp cloth, and  
avoid getting water inside the appliance.  
For AC line powered units, before returning repaired unit to user, use an ohm-meter to measure from both AC plug blades to all exposed  
metallic parts. The resistance should be more than 100,000 ohms.  
14.  
15.  
16.  
Non-use Periods – The power cord of the appliance should be unplugged from the outlet when left unused for along period of time.  
Object and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings.  
Damage Requiring Service – The appliance should be serviced by qualified service personnel when:  
The power-supply cord or the plug has been damaged; or  
Objects have fallen, or liquid has been spilled into the appliance; or  
The appliance has been exposed to rain; or  
The appliance does not appear to operate normally or exhibits a marked change in performance; or  
The appliance has been dropped, or the enclosure damaged.  
17.  
18.  
Servicing – The user should not attempt any service to the appliance beyond that described in the operating instructions. All other servicing  
should be referred to qualified service personnel.  
Ventilation – Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it  
from overheating, and these openings must not be blocked or covered. The opening should never be blocked by placing the product on a  
bed, sofa, rug, or other similar surface. This product should be placed in a built-in installation such as a bookcase or rack unless proper ven-  
tilation in the manufacturer’s instructions have been adhered to.  
19.  
20.  
Attachments – Do not use attachments not recommended by the product manufacturer as they may cause hazards.  
Accessories – Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to  
a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer,  
or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory  
recommended by the manufacturer.  
21.  
22.  
Lightning – For added protection for this product during a lightning storm, or when it is left unused for long periods of time, unplug it from the  
wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.  
Replacement Parts – When replacement parts are required, be sure the service technician has used replacement parts specified by the man-  
ufacturer or have the same characteristics and specifications as the original part. Unauthorized substitutions may result in fire, electric  
shock, or other hazards.  
23.  
Safety Check – Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine  
that the product is in proper operating condition.  
MAIN FEATURES  
10 seconds of anti-shock memory  
Instant start  
Seamless looping  
Large jog wheel for easy cueing of tracks  
Easy to read LCD display  
Adjustable pitch range (+/- 8%, 16%, 25%, 100%) with Key Lock and Pitch Bend  
Auto and manual BPM function  
S/PDIF digital output  
Onboard sampling with four trigger buttons and cue memory  
Auto cue function (-48 dB)  
Selectable elapse, remain and total remaining time display  
Single or continuous play  
Fader start / Relay Play  
CONTROLS & FUNCTIONS  
1.  
SGL/CTN Toggles between Single and Continuous play modes. Continuous mode operates like a normal CD player, playing the entire  
disc without stopping. Single mode only plays one track at a time, returning to the Cue point when the track is completed. The LCD will dis-  
play “SINGLE” when in that mode.  
2.  
3.  
LCD DISPLAY – Shows various information on the status, modes, and functions of the unit.  
TIME – This button switches the time value displayed in the LCD between elapsed track time, remaining track time, and the total remaining  
time for the entire disc. Markers next to the time readout indicate which of these modes is enabled.  
PITCH RANGE INDICATORS – Indicates the pitch range in percent as selected by #5.  
PITCH RANGE BUTTON – Selects between a pitch range of +/- 8, 16, 25, or 100%.  
KEY LOCK BUTTON – Enables the key lock function, which allows the tempo or BPM of the music to be altered without affecting the key, or  
pitch of the music. This button is illuminated when enabled.  
4.  
5.  
6.  
7.  
8.  
PITCH LOCK BUTTON – When illuminated, the pitch control is locked at 0%, regardless of the pitch slider’s position.  
JOG WHEEL – This large wheel has multiple functions:  
• When in pause or cue mode, the jog wheel can be used as a frame search control, allowing you to set it to a  
specific point.  
• During normal playback, the wheel works as a pitch bend, similar to a “push” or a “drag” on a turntable.  
Turning the wheel counter-clockwise temporarily slows down the playback speed according to the speed,  
velocity, and duration that’s applied to the wheel. Turning the wheel clockwise temporarily speeds up the  
playback speed.  
9.  
PITCH SLIDER – Used to adjust the playback pitch percentage. The slider is a set adjustment and will remain set until it is either moved, or  
the PITCH LOCK is turned on.  
10.  
11.  
PITCH BEND BUTTONS – Used to temporarily decrease or increase the playback speed. Pitch will return to the current setting when  
released.  
SAMPLER BUTTON – Once cue or samples are saved to one or all of the BANKS (#13) the SAMPLER button can be engaged (illuminated  
blue). Once in this mode, sounds stored in the BANKS will play regardless of whether the unit is in CUE, PLAY, or PAUSE mode. This  
means that you can play samples at the same time that your CD is playing. Press the SAMPLER button again to disable and stop sample  
playback. The audio sample can even play when there is no disc inside. By using the MODE button (section #21), samples can be played  
once, or looped continuously.  
12.  
LOOP IN / OUT / RELOOP – These buttons control the marker points for seamless, on-the-fly looping. Press IN to set a cue point or the  
starting point of a seamless loop. Press OUT to set the ending point of a loop, and the loop will continue to play until the OUT button is  
pressed again. If a seamless loop has been made, but the CD player is not actively in loop mode (not playing), pressing the RELOOP button  
will instantly reactive the loop. Press OUT to exit the loop. LOOP and RELOOP will appear in the LCD display when the reloop function is  
available. During play mode, pressing the RELOOP button will instantly return play to the last set point without interrupting playback.  
BANK BUTTONS – Four different cue points or samples can be saved to these buttons. See operating instructions for further explanation.  
CLEAR BUTTON – Clears cue points stored in the BANKS (please refer to item #22).  
LOOP SAVE BUTTON – After creating a loop point (#21), pressing this button allows you to store the loop to one of the four BANKS. While  
the SAVE button is flashing red, press one of the BANK buttons to store the loop in that location. Cue points can also be saved by following  
this procedure. BANK locations can also be overwritten in the same way.  
13.  
14.  
15.  
16.  
17.  
PLAY/PAUSE BUTTON – Press to play the CD from the current location, or to pause it at the current location.  
CUE BUTTON – During normal playback, pressing the button immediately returns the track to the last set cue point and pauses playback  
when released. Pressing CUE again will engage the cue monitor, which plays the track from the cue point until you release the CUE button.  
If you press pause (#25) at any time other than the currently stored cue point, pressing CUE will reset the cue point to the new position.  
SEARCH BUTTONS – Allows you to search through a track or a CD in either direction. While in pause mode, tracks can be moved one  
frame at a time. Holding down one of these buttons will cause the search in that direction to occur at a faster rate.  
TRACK BUTTONS Tapping one of these buttons will skip to the previous or next track. Holding it down will rapidly skip through the tracks.  
OPEN/CLOSE BUTTON – Opens or closes the CD tray. The CD will only eject while in pause or cue mode, and will not work while a CD is  
playing. If the tray is left open, it will close automatically after a brief time.  
18.  
19.  
20.  
21.  
SAMPLER MODE – Press the MODE button to switch between ONE SHOT or LOOP mode. ONE SHOT will play the samples once, then  
end. LOOP MODE will continue to play the sample over and over.  
22.  
23.  
24.  
AUDIO OUT – This analog output signal requires a pair of RCA cables (left and right) to be connected to a line or aux input.  
DIGITAL OUT – This digital output signal requires one SP/DIF cable to be connected to a SP/DIF input on your mixer or computer.  
FADER START / RELAY – This connection allows two CD players to be linked for relay play. This can also be connected to a mixing board  
that supports automatic fader start.  
25.  
VENT SLITS – These openings are used for the proper ventilation of the unit. In order to prevent overheating and to insure proper operation,  
do not cover or block these slits.  
26.  
27.  
POWER BUTTON – Turns the unit on and off.  
AC IN – Plug in the power supply cable here. The plug can only be inserted in one direction, so do not force it in.  
28.  
29.  
TRACK – Indicates the current track selected or being played.  
WHEEL INDICATOR – This is a visual representation of a vinyl marker, which is traditionally used to mark the location of a certain sound or  
cue point on a vinyl record. Here, it indicates the play position, rotates during playback in either direction, and stops during cue or pause  
mode. It also indicates the speed of the forward and reverse search operation.  
30.  
31.  
32.  
33.  
PLAY – Indicates when the unit is currently playing a CD.  
PAUSE – Indicates the unit is in CUE or PAUSE mode.  
CUE – Indicates the unit is at a cue point and is ready to play.  
ANTI SHOCK AND BUFFER INDICATOR – Indicates the current status of the buffer memory. This is represented on the display by a buck-  
et being filled or emptied. The bucket itself represents the instant start function (which works by buffer memory). If the bucket is flashing, the  
instant start is not available. Each bar within the bucket represents 2 seconds of anti shock protection. There is up to 10 seconds of anti  
LCD DISPLAY  
shock protection available.  
34.  
35.  
36.  
37.  
38.  
AUTO INDICATOR – Indicates when Auto Cue mode is active.  
PITCH VALUE – Shows the percentage of the pitch slider.  
PITCH – Indicates when the pitch percentage is displayed.  
TIME BAR – Shows a proportionate visual representation of the time remaining or time elapsed.  
TIME DISPLAY – Displays the time of track(s) currently selected in increments of Minutes, Seconds, and Frames.  
39.  
ELAPSED / TOTAL / REMAIN – Indicates whether the time shown on the display refers to total remaining time or track remaining time. If  
either of these are not illuminated, this indicates elapsed track time.  
40.  
41.  
42.  
RELOOP – Indicates when there is a previously set loop, and that the loop is ready to be played again.  
LOOP – Indicates when the CD is in loop mode.  
SINGLE – Controlled by the SGL/CTN button, this indicates when the unit is set to play just one track at a time. When this is not illuminated,  
the CD will play continuously through all tracks.  
SET-UP  
A)  
B)  
CHECKING THE CONTENTS – Check that the carton contains all of the following items.  
Tabletop CD player unit  
• User’s manual  
• One pair RCA cable  
• One power cable  
• One fader start / relay cable  
INSTALLING THE UNIT  
• Place the unit on a flat, level surface.  
• Be sure the player is in a well-ventilated area where it will not be exposed to direct sunlight, high  
temperatures, or high humidity.  
• Try to place the unit as far as possible from Tvs and tuners, as the unit may cause undesirable interference.  
• The player will work normally when the unit is within 15 degrees of the vertical plane. If the unit is tilted  
excessively, discs may not load or unload properly, or playback may be adversely affected.  
• The unit’s LCD screen is designed to be clearly visible within the angles shown in the figure below. Place the  
unit so that the LCD screen is within this visual range for optimal clarity.  
CONNECTIONS  
• Make sure that the unit and any other equipment in the signal chain are turned off prior to making  
any connections.  
• Connect the RCA cable to the rear of the unit and to the input on your mixer.  
• Connect the power cable to the rear of the unit and to a proper AC outlet.  
C)  
D)  
CAUTION  
• Be sure to use the supplied cables. Using other types of cables may result in unit damage.  
To avoid severe damage to the unit, be sure the power is OFF when making any connections.  
OPERATING INSTRUCTIONS  
1.  
OPENING AND CLOSING  
This operation only works when the power is turned on. Press the OPEN/CLOSE button to open or close the disc tray, or press the PLAY  
button and the disc tray will close automatically. If the tray is not closed after 60 seconds it will close automatically and enter pause mode.  
The disc tray cannot be opened during playback. This prevents playback from being interrupted if the OPEN/CLOSE button is pressed acci-  
dentally. Stop playback by engaging cue or pause mode, and then press the OPEN/CLOSE button.  
LOADING DISCS  
Hold a disc by its edges and place on the disc tray with the label side facing up. Do not touch the play surface (glossy side). CAUTION: Do  
not place foreign objects on the disc tray and do not place more than one disc on the tray at a time. Doing so may result in malfunction and  
damage of the unit. Do not push the disc tray in manually when the power is off, as this may also result in malfunction and damage.  
SELECTING TRACKS  
2.  
3.  
Select the desired track by pressing the TRACK buttons to move to the previous or next track, or by holding down the TRACK buttons to  
change tracks continuously at a higher speed. When a new track is selected during playback, playback begins as soon as the track selection  
operation is completed.  
4.  
5.  
6.  
7.  
STARTING PLAYBACK  
Press the PLAY/PAUSE button during the pause or cue mode to start playback. The PLAY/PAUSE button illuminates with a solid green light  
during playback.  
STOPPING PLAYBACK  
There are two ways to stop playback. Press the PLAY/PAUSE button during playback to pause at that point, or press the CUE button during  
playback to return to the position at which playback started (back cue).  
PAUSING  
Press the PLAY/PAUSE button to switch between play and pause. The PLAY/PAUSE button illuminates with a flashing green light when  
paused.  
CUEING  
Cueing is the action of preparing tracks for playback. When the CUE button is pressed, playback returns to the cue point and enters pause  
mode. When the PLAY/PAUSE button is pressed during the cue mode, playback starts.  
SETTING CUE POINTS  
• When using the jog wheel to set the specific start point or by skipping to a new track during play or pause, the  
beginning play point will be set as the cue point.  
• During playback, press the IN loop button to set a cue point on the fly. To return to this new cue point, press  
the CUE button and then press the PLAY/PAUSE button to resume playback from this new cue.  
• Cues can be stored to one of the four BANK buttons.  
8.  
9.  
AUTO CUE  
When a disc is initially loaded, the cue point is set to the first source or music or sound. If the track is changed before pressing play, the cue  
point is changed to the first source of music or sound on that track. Pressing pause during playback also creates a new cue point.  
FRAME SEARCH / FAST FORWARD / FAST REVERSE  
By pausing playback first, the jog wheel can be used to locate a specific cue point frame by frame. Moving the jog wheel gently counter-  
clockwise moves the cue point back in time, while moving the jog wheel clockwise moves the cue point forward in time. As the wheel is  
moved, the monitor function allows you to hear the sound that is located at that frame or position in time. When the desired location is found,  
press the CUE button, then press the PLAY/PAUSE button to resume playback from this new cue. Moving the jog wheel faster in either  
direction will allow you to scan quickly through a disc or track. This fast forward and fast reverse feature has four speeds, responding to how  
fast you turn the jog wheel.  
10.  
LOOP PLAY  
You can create a seamless, continuous loop between two points.  
• Engage playback by pressing the PLAY/PAUSE button, causing it to illuminate solid green (not flashing).  
• Set the start point of the seamless loop by pressing the IN button at the desired point in time. This will cause the OUT button to flash  
green.  
• Set the end point of the seamless loop by pressing the OUT button at the desired point in time. Playback will  
immediately return to the previously set IN point and play to the OUT point, creating a seamless loop without  
interruption. The RELOOP button will now be flashing green, and the LOOP indicator on the LCD screen will now be flashing.  
To exit the loop, press the OUT button again. When the music reaches the OUT point, it will play through it  
instead of looping back to the IN point.  
To replay or re-enter the loop, press the RELOOP button. The loop can be re-triggered by pressing the  
RELOOP button again and again. Press the OUT button to exit the loop again.  
11.  
MODIFYING LOOPS  
Once a seamless loop is created, the OUT point can be changed. Simply exit the loop by pressing OUT and then press it again once the  
new point in time is reached. For a shorter loop, make sure to exit the loop by pressing OUT immediately after the loop starts from the IN  
point, and press OUT again quickly.  
12.  
13.  
TIME DISPLAY  
During normal playback, each time you press the TIME button (#3), the display changes between elapsed time, track remaining time, and  
total disc remaining time.  
PITCH BENDING  
Pressing the PITCH BEND – or PITCH BEND + buttons will decrease or increase the speed of playback temporarily. The extent to which the  
speed is changed is proportionate to the amount of time the button is pressed. For example, if the PITCH BEND + button is held in continu-  
ously, the speed continues to increase until the maximum limit set by the PITCH RANGE is reached. Once the PITCH BEND + button is  
released the pitch will return to the pitch set by the PITCH SLIDER. The jog wheel can also be used to temporarily bend the pitch of the  
music during normal playback. Rotate the wheel clockwise to speed up and counter-clockwise to slow down. The speed that you rotate the  
jog wheel determines the percent of pitch bend. It is recommended that you use the outer edge of the jog wheel for this type of control, as  
touching the top surface may cause interruption of playback in certain modes of operation.  
MEMORY CUEING (SETTING A CUE POINT – BANK BUTTONS)  
14.  
Labeled 1 through 4, these banks store cue points, samples, or loops. Pressing one of the BANK buttons will store a cue point at the exact  
time it was pressed. The button will flash red, and then turn solid green, letting you know that a cue point has been stored. Press the button  
again, and playback will seamlessly restart from the stored cue point and the button will turn red. You can repeatedly press the BANK button  
to create a stuttering effect. If the unit is in pause or cue mode, pressing the button will start playback from the stored cue point, but will only  
keep playing while the button is depressed. To clear or delete cue points from memory, simply press the CLEAR button (#23). While it is  
flashing red, press the BANK button(s) you wish to clear and those buttons will also flash red. Press CLEAR once more to complete the  
process, and the BANK lights will now turn off, letting you know that there is no information stored in them. After cue points are stored to one  
of the BANKS, pressing the SAMPLER button (#20) will engage SAMPLER mode (please refer to item #20).  
MEMORY BACKUP  
15.  
16.  
This will automatically retain the setting you have made for continuous or single play mode, even if you unplug the unit.  
FADER START  
By connecting the CD player to a mixing board that has the fader start feature, the crossfader will engage playback or cue mode depending  
on its location. If the CD player is connected to the left side of the crossfader, playback will start once the fader is moved from the left most  
position towards the right. The CD player will re-cue itself when the crossfader is brought back to the left most position. Two CD players can  
be hooked up in this fashion to work on both sides of the crossfader.  
17.  
RELAY PLAY USING TWO PLAYERS  
When both CD players are connected to each other via their FADER START / RELAY jacks, the players can work in unison by playing tracks  
one after another from both units.  
• Set both players to single play mode (the SINGLE indicator will be illuminated in the LCD displays).  
• Begin playback on the first player.  
• When the first track ends, playback will automatically start on the second player and the first player will automatically enter standby mode.  
• When the track on the second player ends, the first player will play the next track. The players will continue to  
perform continuous relay play until stopped or until the last track is played.  
• By setting a cue point on the standby player, you can perform relay to any desired cue point on the selected  
track.  
NOTE: Relay play may not work properly if the audio outputs on both players are not connected to the same  
audio input, amplifier, or if the mixing board is not set up properly.  
19.  
23.  
STUTTER EFFECTS  
Similar to the sound of a CD skipping, this effect can be created and controlled in a variety of ways.  
• Rapidly pressing the CUE button.  
• By storing a cue point to one of the four BANK buttons and pressing them rapidly.  
• By creating a seamless loop, and rapidly pressing the RELOOP button.  
• By creating a seamless loop with a very short duration.  
• By pressing PAUSE while audio is playing in CD Jog mode.  
SLEEP MODE  
The CD player automatically shuts off the transport and laser and displays “SLEEP MODE” in the LCD screen after being left in pause or cue  
mode for 15 minutes. This will lengthen the life of your motor drive, laser, and LCD screen. To wake up your unit from sleep mode, simply  
press CUE, or PLAY/PAUSE.  
SPECIFICATIONS  
1. APPLICATION Model C303  
2. POWER SOURCE AC 120V, 60Hz, 12W  
3. DIMENSIONS  
4. WEIGHT  
318 (W)x 358 (D)x 92 (H) mm  
4.9 Kgs  
5. FEATURES  
• Anti-shock playback  
• Instant start  
• Seamless loop  
• Pitch control  
• Key Lock  
• 4 banks sampler & cue memory  
• Auto cue  
6. AUDIO CHARACTERISTICS (TEST DISC: TCD-782, LOAD=47Kohm)  
ITEM  
Output level  
Channel balance  
Frequency response  
De-emphasis response +2.5/-0dB  
Channel separation*2  
T.H.D. + NOISE*1  
S/N ratio*2  
TYPICAL  
1Vrms+/-0.5dB  
within 0.5dB  
LIMIT  
1Vrms+/-1dB  
within1dB  
CONDITION  
1KHz,0dB  
1KHz,0dB  
0dB output  
16KHz,-20dB  
1KHz,0dB  
1KHz,0dB  
1KHz,0dB  
(1)  
(2)  
(3)  
(4)  
(5)  
(6)  
(7)  
20-20KHz,+/-0.3dB 20-20KHz,+/-1dB  
+3/-0dB  
90dB  
0.01%  
100dB  
95dB  
0.006%  
120dB  
NOTE: *1 With 20KHz low pass filter. *2 With 20KHz low pass filter, ”IHF-A” weighted.  
7.SEARCHING TIME (TEST DISC: TCD-792)  
ITEM  
TYPICAL LIMITS CONDITION  
(1)  
(2)  
Short access time 2sec  
Long access time 4sec  
4sec  
6sec  
Play next track  
Track 1 ->Track 20  
Track 20 ->Track 1  
8. PLAYABILITY  
ITEM  
TYPICAL LIMIT  
CONDITION  
(1)  
(2)  
(3)  
(4)  
(5)  
Interruption  
1mm  
0.6mm TCD-725  
75um  
0.7mm TCD-725  
Black dot 1mm  
Finger prints  
Eccentricity  
65um  
TCD-725  
140um 140um TCD-712 W/O TRACK JUMP  
Vertical deviation 1mm  
0.5mm TCD-731R  
9. ACCESSORIES  
(1)  
(2)  
(3)  
(4)  
Connected RCA cable  
1 set for L and R channel  
Operating Instruction  
Auto-start cable  
AC Cord  
1 pc  
1 pc  
1 pc  
NOTE: *1 with 20Khz low pass filter  
6. SEARCHING TIME (TEST DISC: TCD-792)  
*2 with 20Khz low pass filter, “IHF-A” weighted  
ITEM  
Short access time  
Long access time  
TYPICAL  
2sec  
4sec  
LIMIT  
4sec  
6sec  
CONDITION  
Play next track  
Track 1-> Track 20  
(1)  
(2)  
Track 20 -> Track 1  
7.PLAYABILITY  
ITEM  
Interruption  
Black dot  
Finger prints  
Eccentricity  
Vertical deviation  
TYPICAL  
1mm  
1mm  
75um  
140um  
1mm  
LIMIT  
CONDITION  
0.7mm  
0.6mm  
65um  
140um  
0.5mm  
TCD-725  
TCD-725  
TCD-725  
TCD-712 W/O TRACK JUMP  
TCD-731R  
8. PICK-UP  
System  
Object lens drive system optical pick-up  
2 dimensional paralleled drive  
3 spot beam detection  
Semiconductor laser  
Object lens drive system  
Tracking detection  
Optical source  
Wave length  
780nm  
9. GENERAL  
System  
Compact Disc Digital Audio  
Disc loading  
Display  
Front loading  
LCD  
Pitch control range  
Pitch bend  
Pitch accuracy  
Within +/-8%, +/-16%, +/-25%, +/-100%  
+/-100%  
0.1%  
10.ENVIRONMENTAL  
Operating Temperature  
Humidity  
CONDITION  
5 to 35 deg. C  
25 to 85% RH (non-condensing)  
-20 to 60 deg. C  
Storage Temperature  
11. ACCESSORIES  
(1)  
(2)  
(3)  
Connected RCA cable  
User’s manual  
Fader start cable (1/8” jack) 1 pc  
1 set for L and R channel  
1 pc  
12. NOTES  
The specifications are subject to change to any improvement by negotiations in advance.  
The parts are subject to change to any improvement within the range of the specifications.  
WARRANTY & RETURN POLICY  
Warranty  
Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, without charge,  
repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved  
defective in material or workmanship for a period of one (1) following the date of original purchase. Exceptions to this warranty are as noted below:  
The warranty for mechanical parts which are subject to wear and tear are limited to the earlier to occur of thirty (30) days following the date of original  
purchase or the following number of cycles: Faders - 15,000; Rotary potentiometers - 10,000; and Switches - 10,000.  
Stanton will warrant all replacement parts and repairs for ninety (90) days from the date of original shipment. Repairs made necessary by reason of  
misuse, alteration, normal wear, or accident are not covered under this warranty.  
Returns  
Authorized Stanton dealers are only authorized to sell and distribute merchandise within a specific country. All goods requiring warranty repair or  
replacement must be returned (freight prepaid if not hand-delivered) to the authorized Stanton dealer from whom the merchandise was purchased and  
in the same country where the merchandise was purchased. For purposes of purchases made via the Internet, the merchandise must be returned to  
the authorized Stanton dealer in the country where the authorized Stanton dealer which sold the merchandise to purchaser is located and not the  
authorized Stanton dealer in the country where the purchaser is located or the country in which the merchandise was received. Any returns to a non-  
authorized dealer or to an authorized Stanton dealer not in the same country as the merchandise was intended to be sold or as set forth above will void  
this warranty.  
To initiate a warranty repair, you must contact the authorized Stanton dealer from whom you purchased the merchandise, and follow such authorized  
Stanton dealer’s return policy.  
Stanton assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the merchandise.  
Stanton’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party, or product liability, and relating  
to the merchandise shall not exceed the price received by Stanton from your purchase of such merchandise. In no event will Stanton be liable for any  
special, incidental or consequential damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negli-  
gence of Stanton or otherwise. To the extent permitted by law and except as otherwise provided above, Stanton disclaims any express or implied war-  
ranties of merchantability or fitness for a particular purpose.  
The above warranty provides you with specific legal rights. You may also have additional rights, which are subject to variation from state to state and  
country to country.  
If there is a dispute regarding the warranty of merchandise that does not fall under the warranty conditions stated above, please include a written  
explanation with the merchandise when returned pursuant to the terms and conditions set forth herein.  
Stanton Magnetics, Inc, 3000 SW 42 St. Hollywood, Florida 33312.  

Wibur Curtis Company CAFE 3DB User Manual
Sony RM TP501 User Manual
Sony MicroVault USM8GE User Manual
SmartDisk PowerPlay User Manual
Seagate Cheetah NS SAS ST3400755SS User Manual
Samsung SGH M300 User Manual
Samsung SCH X799 User Manual
Samsung Cell Phone SGH i450 User Manual
Philips S890 User Manual
Oregon Scientific WS902H User Manual