3-234-030-12(1)
Portable
MiniDisc Recorder
Operating Instructions
“WALKMAN” is a
trademark of
Sony Corporation.
MZ-R909
©2001 Sony Corporation
3
Table of contents
List of menus ........................................................................................11
a track ..............................................................................29
To start/stop recording in sync with the source player
Stamp) ...................................................................................................35
4
track names (Index Search) ............................................ 42
Searching for a specific point while monitoring the elapsed time
5
Labeling recordings ..............................................................................55
Erasing a track mark .............................................................................68
(G-PROTECTION) ...............................................................................70
6
Battery life ..................................................................................... 75
Precautions ........................................................................................... 76
Troubleshooting ................................................................................... 79
Messages .............................................................................................. 84
Specifications ....................................................................................... 87
What is an MD? ................................................................................... 88
7
Looking at controls
See pages in ( ) for more details.
The recorder
1
2
3
4
9
J
5
6
qa
qs
qd
qf
qg
qh
7
8
The MIC (PLUG IN POWER) jack
has a tactile dot.
G Terminals for attaching dry battery
case (20)
The VOL +/– button has a tactile dot.
P i (headphones/earphones)/LINE
8
The display window of the recorder
1
2
3
4
5
6
7
8
9
q;
qa
qs
G SYNC (synchro-recording) indication
Displays the disc and track names,
date, error messages, track numbers,
etc.
I STEREO (SP stereo), LP2 (LP2
stereo), LP4 (LP4 stereo), MONO
J Pause indication
Shows that the disc is rotating for
recording, playing or editing an MD.
Lights up when Digital Sound Preset
is on.
Shows the play mode (shuffle play,
program play, repeat play, etc.) of the
MD.
Lights up while recording. When
flashing, the recorder is in record
standby mode.
Shows approximate battery condition.
9
The headphones/earphones with a remote control
A B C DEF
G
H
I
J
K
N> : play, AMS, FF
. : REW
Turn or turn and hold to play, fast
forward, rewind, etc.
E Clip
Pull and turn to adjust the volume.
1)May be used as the “Enter” button, depending
on the function.
The display window of the remote control
A
B
C
D
E
F
G
H
10
How to use the jog dial
The jog dial on the recorder can be used to perform various operations during playback,
recording, editing, and when the recorder is stopped.
Jog dial
Push to enter
Turn to select
Display window while selecting the menu items
Press the jog dial to display menu items in the display window on the recorder. Turn the jog
dial down to scroll downward, and turn it up to scroll upward. Press the jog dial while an
item is flashing in the display to select it.
EDIT
DISPLAY
PLAY MODE
DISPLAY
PLAY MODE
REC MODE
EDIT
DISPLAY
Turn the jog dial up to scroll
the display upward
Turn the jog dial down to
scroll the display downward
List of menus
Menu functions
Press the jog dial on the recorder or press DISPLAY for 2 seconds or more on the remote
control to enter a menu.
Menu on the Menu on the Functions
recorder1)
remote
control1)
EDIT
EDIT
Selecting editing operations (labeling, erasing tracks,
69).
DISPLAY
—
—
—
Displaying elapsed playing time, remaining playing
PLAY MODE
RecVolume
Selecting the play mode (repeat play, shuffle play, etc.)
Selecting the automatic or manual recording level
11
Menu on the Menu on the Functions
recorder1)
remote
control1)
REC MODE
—
Selecting the recording mode (SP stereo, LP2 stereo,
M-TIMER
AUDIO OUT
SOUND
M-TIMER
—
—
Selecting “SOUND 1” or “SOUND 2” (Digital Sound
—
—
SPEED
GROUP
PERSONAL PERSONAL Entering or erasing the disc information in the Personal
SYNC REC
—
Selecting “ON” or “OFF” of synchro recording
TIME MARK
MIC SENS
—
—
—
SEARCH
Selecting Index search (searching while monitoring
track numbers or track names) or Time search
(searching while monitoring the elapsed time)
OPTION
OPTION
—
• AVLS (Automatic Volume Limiter System) —
• BEEP (headphones/earphones beep) — Selecting
• REC-Posi — Selecting the start point when recording
• LP Stamp — Selecting “Stamp ON” (“LP:” will be
added at the beginning of the track name) or “Stamp
• CONTRAST — Adjusting the contrast of the display
1) The menu items that can be selected vary according to the on/off status of group mode or the operating
status of the recorder.
z
(page 48) menu functions on the remote control, use the respective buttons.
12
Tables of Menus on the recorder
The menus provided on the recorder for each operating status are shown on this and the
following pages. Each chart shows the various menus and the menu items that can be
operations. Menus and menu items toggle in the display.
Menus and menu items selected while the recorder is stopped
EDIT
:Name
:Set
:Release1)
Name Bank
BankErase
:Erase
:Erase1)
Clock
DISPLAY
LapTime
RecRemain
AllRepeat
GP Remain1)
AllRemain
PLAY MODE
Normal
1 Track
PGMRepeat
LP4
1 Repeat
PGM
Shuffle
Shuf. Rep
REC MODE
SP
LP2
MONO
M-TIMER
OFF
ON
TIMER 1
TIMER 2
TIMER 3
AUDIO OUT
HeadPhone
SOUND
LINE OUT2)
, : Pressing the jog dial
h : Turing the jog dial
SOUND OFF
SOUND 1
SOUND 2
continued to the next page
13
continued from the last page
PERSONAL
Entry?
Erase?
SYNC ON
SENS LOW
BEEP
SYNC REC
SYNC OFF
MIC SENS
SENS HIGH
OPTION
, : Pressing the jog dial
h : Turing the jog dial
AVLS
REC-Posi3)
LP Stamp
CONTRAST
AVLS OFF
AVLS ON
From Here
From End
CLOCK SET
BEEP ON
BEEP OFF
Stamp ON
Stamp OFF
1) Appears only when the recorder is played and then stopped while in group mode.
2) Does not appear when the supplied remote control is connected to the i/LINE OUT jack.
3) Selectable only when the group mode is turned off.
Press CANCEL on the recorder to cancel a menu operation.
14
Menus and menu items selected while the recorder is playing
EDIT
:Move1)
:Erase
:Name
:Name1)
Name Bank
:Move
DISPLAY
LapTime
1 Remain
AllRepeat
GP Remain1)
AllRemain
Rec Date
PLAY MODE
Normal
1 Track
1 Repeat
PGM
Shuffle
PGMRepeat
Shuf. Rep
M-TIMER
OFF
ON
TIMER 1
TIMER 2
TIMER 3
AUDIO OUT
LINE OUT3)
HeadPhone
SOUND
SOUND OFF
SOUND 1
Erase?
SOUND 2
PERSONAL
OPTION
Entry?
AVLS
, : Pressing the jog dial
h : Turing the jog dial
BEEP
AVLS OFF
AVLS ON
BEEP ON
BEEP OFF
1) Appears only when the recorder is played and then stopped while in group mode.
2) Does not appear when the supplied remote control is connected to the i/LINE OUT jack.
Press CANCEL on the recorder to cancel a menu operation.
15
Menus and menu items selected while the recorder is recording
EDIT
:Name
:Name1)
RecRemain
ManualREC
LP2
:Name
Name Bank
DISPLAY
LapTime
Clock
2)
Rec Volume
Auto REC
2)
REC MODE
SP
LP4
MONO
AUDIO OUT
LINE OUT3)
HeadPhone
SOUND
SOUND OFF
SOUND 1
5 min. ON
SYNC ON
SENS LOW
SOUND 2
TIME MARK
OFF
10 min. ON
15 min. ON
SYNC REC
SYNC OFF
MIC SENS
SENS HIGH
OPTION
, : Pressing the jog dial
h : Turing the jog dial
AVLS
AVLS OFF
AVLS ON
1) Appears only when the recorder is played and then stopped while in group mode.
2) Does not appear when the supplied remote control is connected to the i/LINE OUT jack.
3) Selectable only when the group mode is turned off.
Press CANCEL on the recorder to cancel a menu operation.
16
Tables of menus on the remote control
The menus provided on the remote control for each operating status are shown on this and
the following pages. Each chart shows the various menus and the menu items that can be
operations. Menus and menu items toggle in the display.
Menus and menu items selected while the recorder is stopped
EDIT
GPRelease1)
Name Bank
BankErase
:Name
GP:Set
M-TIMER
OFF
ON
TIMER 1
TIMER 2
TIMER 3
GROUP
GROUP OFF
PERSONAL
GROUP ON
Erase?
Entry?
Index
AVLS
SEARCH
OPTION
, : Pressing x
h : Turing the control
Time
BEEP
AVLS OFF
AVLS ON
BEEP ON
BEEP OFF
1) Appears only when the recorder is played and then stopped while in group mode.
Press DISPLAY for 2 seconds or more on the remote control to cancel a menu operation.
17
Menus and menu items selected while the recorder is playing
EDIT
:Name
OFF
GP:Name1)
Name Bank
:Move
GP:Move1)
:Erase
M-TIMER
ON
TIMER 1
TIMER 2
TIMER 3
SPEED
GROUP
GROUP OFF
PERSONAL
GROUP ON
Erase?
Entry?
Index
AVLS
SEARCH
OPTION
, : Pressing x
h : Turing the control
Time
BEEP
AVLS OFF
AVLS ON
BEEP ON
BEEP OFF
1) Appears only when the recorder is played and then stopped while in group mode.
Press DISPLAY for 2 seconds or more on the remote control to cancel a menu operation.
Menus and menu items selected while the recorder is recording
, : Pressing x
h : Turing the control
EDIT
:Name
GP:Name1)
:Name
Name Bank
1) Appears only when the recorder is played and then stopped while in group mode.
Press DISPLAY for 2 seconds or more on the remote control to cancel a menu operation.
18
Getting started
Charge the rechargeable battery before using. Even if the rechargeable
battery is not charged, you can use the recorder as long as the AC
power adaptor is connected.
1
2
Insert the rechargeable battery
Insert the rechargeable battery minus
end first.
Charging the rechargeable battery
How to assemble the
battery charging stand
Make sure all the parts of the
battery charging stand are
firmly attached.
To a wall
outlet
Supplied AC
power adaptor
To DC IN 3V
Make sure to check the
CHARGE lamp lights up.
1 Connect the supplied AC power adaptor to DC IN 3V.
2 Place the recorder on the battery charging stand.
Full charge takes about 6 hours and then the CHARGE lamp will
go off when charging completes.
19
Do not operate the recorder when you place it on the battery charging stand
or during the charging. If you do so, it may cause the recorder to malfunction
or prevent the battery from charging.
Using the dry battery
Attach the dry battery case to the recorder.
Insert the battery minus end first.
3
4
2
1
Insert a LR6 (size AA) alkaline dry battery.
To operate the recorder for the longest possible time, use the dry battery together with a
fully charged rechargeable battery.
3
Make connections and unlock the
control
connect firmly
To i/LINE OUT
HOLD
1 Connect the headphones/earphones
2 Slide HOLD to the direction of the arrow
(.) in the illustration to unlock the
controls.
with the remote control to i/LINE OUT.
20
4
Insert an MD (Use a recordable MD for
recording.)
1 Press OPEN to open the lid.
2 Insert an MD with the label side facing
front, and press the lid down to close.
• When the battery life of a fully charged
rechargeable battery becomes about half the
normal life, replace it.
z
You can also charge the battery by connecting
the supplied AC power adaptor directly to the
recorder.
• Make sure to remove the recorder from the
battery charging stand and disconnect the AC
power adaptor from the wall outlet as soon as
charging is complete. Keeping it connected to
the power source for a long time may reduce
the operating efficiency of the battery.
• Please note the following points when
charging the battery directly with the supplied
AC power adaptor.
—If you press x/CHG immediately after
charging has completed, charging will
begin again. If this happens, press x/CHG
again to stop the charging operation since
the battery is already fully charged.
1 Connect the supplied AC power adaptor to
DC IN 3V on the recorder, and then press
x/CHG while the recorder is stopped.
“Charging” and e appear in the display
and charging starts. Full charging takes
about three and a half hours. Charging is
complete when e disappears. Charging
time may vary depending on the battery
condition.
2 Unplug the AC power adaptor from the AC
power outlet.
Notes
• The supplied battery charging stand can be
used only with this recorder. Any other
models cannot be charged.
• Do not use the recorder to charge any other
battery besides the supplied one or the one
designated for it (NH-14WM(A)).
• Though the battery charging stand and the
battery may become hot during the charging
procedure, this poses no danger.
• Be sure to use the supplied AC power adaptor.
• When a rechargeable battery is charged for the
first time or charged after a long period of
disuse, battery life may be shorter than usual.
Repeat discharging and recharging a few
times. The battery life should return to
normal. The rechargeable battery can be
recharged approximately 300 times.
—Charging stops when you try to operate the
recorder during charging.
• If you remove the recorder from the battery
charging stand for more than 3 or 4 seconds
while it is charging, and then return it to the
stand, the CHARGE lamp will not go off until
approximately 6 hours later, no matter how
many hours the recorder had been on the stand
till then. Please note, however, that the
recorder will become full charged when the
total time on the stand (the time up until you
removed it and the time after you returned it to
the stand) reaches approximately 6 hours,
even if the CHARGE lamp does not go off.
21
Recording an MD right away!
Connect to a digital source using an optical cable to make digital
recordings. Digital recording is possible even from digital equipment
with different sampling rates, such as a DAT deck or a BS tuner, using
the built-in sampling rates converter (see “Note on digital recording”
analog input (line cable required)” (page 28). To record a track into an
existing group, see “Recording tracks using the Group Function
(Group mode recording)” (page 30). It is recommended to use the
supplied AC power adaptor when recording.
1
Make connections (Insert the cables
firmly and completely into the appropriate jacks.)
CD player, MD
player, DVD
video player, etc.
Portable CD
player, etc.
to a wall outlet
to DIGITAL OUT
(OPTICAL)
Optical
Optical plug
mini-plug
AC power adaptor
Optical cable
to DC IN 3V
to LINE IN (OPT)
22
2
Specifying the recording position
3 In order not to record over the current
Jog dial
contents, turn the jog dial until “From
End” flashes in the display, and then
press the jog dial.
All new material will then be recorded
after the end of the current contents.
To record over the current contents,
1 While the recorder is stopped, press
the jog dial, turn the dial until
turn the jog dial until “From Here”
flashes in the display, and then press
the jog dial.
The current contents will then be
recorded over whenever new material
is recorded.
“OPTION” flashes in the display, and
then press the dial again.
2 Turn the jog dial until “REC-Posi”
flashes in the display, and press the jog
dial,
3
Record an MD
1 Press and slide REC to the right.
REC
“REC” and REC indicator on the REC
switch light up and recording starts.
x
2 Play the CD or tape you want to record.
To stop recording, press x.
After you press x to stop, the recorder will
automatically turn off in about 10 seconds
(when using batteries) or about 5 minutes
(when using AC power adaptor).
To
Press
Record from the end of the current
contents1)
END SEARCH and then press and slide REC
to the right.
Record over partway through the previous Press N, ., or > to find the start
recording1)
point of recording and press x to stop.
Then press and slide REC to the right.
Pause
X2)
Press X again to resume recording.
Remove the MD
x and open the lid.3) (The lid does not open
while “TOC Edit” flashing in the display.)
23
1) By setting “REC-Posi” to “From End”, recording operations will always start from the end of the
2) A track mark is added at the point where you press X again to resume recording while pausing; thus
the remainder of the track will be counted as a new track.
3) If you open the lid while “REC-Posi” is set to “From Here”, recording will begin with the first track
the next time you record. Check the point to start recording on the display.
If the recording does not start
• Make sure the recorder is not locked (pages
• Make sure the MD is not record-protected
z
• LINE IN (OPT) jack is for both digital and
analog input. The recorder automatically
recognizes the type of line cable and switches
to digital or analog input.
• The recording level is adjusted automatically.
To adjust the level manually, see “Adjusting
• You can monitor the sound during recording.
Connect the supplied headphones/earphones
with remote control to i/LINE OUT and
adjust the volume by pressing VOL +/–. This
does not affect the recording level.
• Premastered MDs cannot be recorded over.
For models supplied with the AC plug
adaptor
If the AC power adaptor does not fit the wall
outlet, use the AC plug adaptor.
Notes
• “Data Save” or “TOC Edit” flashes while data
of the recording (the track’s start and end
points, etc.) is being recorded. Do not move or
jog the recorder or disconnect the power
source while the indication is flashing in the
display.
• The lid does not open until “TOC Edit”
disappears in the display.
• If the power supply is disrupted (i.e. the
battery is removed or becomes exhausted or
the AC power adaptor is disconnected) during
a recording or editing operation, or while
“TOC Edit” appears in the display, then it will
not be possible to open the lid until power is
restored.
• You can make digital recording only from an
optical type output.
• When recording from a portable CD player,
set the CD player to pause, and then do the
recording procedure on the recorder.
• Note the following when recording from a
portable CD player:
—Some portable CD players may not be
capable of digital out unless powered by the
AC power. If this is the case, connect the
AC power adaptor to the portable CD player
and use it on AC power as the power source.
—On some portable CD players, optical
output may not be possible when using an
anti-skip function (e.g., ESP*). If this is the
case, turn off the anti-skip function.
∗ Electronic Shock Protection
24
Playing an MD right away!
1
Play an MD
1 Press N. Turn the control towards
N> on the remote control.
VOL +/–
N/x
A short beep sounds in the headphones/
earphones when you operate on the
remote control.
2 Press VOL +/– to adjust the volume.
Pull and turn the control towards VOL +/
– on the remote control.
The volume will be shown in the
display. After you adjust the volume,
push back the control.
To stop play, press x.
A long beep sounds in the headphones/
earphones when you operate on the remote
control.
Control
x
Playback starts from the point you last stopped playing. To start playback from the beginning of the
disc, press N for 2 seconds or more on the recorder, or turn and hold the control towards N> for
2 seconds or more on the remote control.
After you press x to stop, the recorder will automatically turn off in about 10 seconds (when using
batteries) or about 5 minutes (when using AC power adaptor).
To
Press (Beeps in the headphones/earphones3))
Find the beginning of the current .. Turn the control towards . on the remote
track1)
control. (Three short beeps)
Find the beginning of the next
track2)
>. Turn the control towards N> on the remote
control. (Two short beeps)
Go backwards while playing
Go forward while playing
Pause
Press and hold .. Turn and hold the control
towards . on the remote control.
Press and hold >. Turn and hold the control
towards N> on the remote control.
X (Continuous short beeps)
Press X again to resume play.
Remove the MD
x and open the lid.4)
1) If you press . during the first track of the disc, the recorder goes to the beginning of the last track
on the disc.
2) If you press > during the last track of the disc, the recorder goes to the beginning of the first track
on the disc.
25
4) Once you open the lid, the point to start play will change to the beginning of the first track (except when
the disc information is stored to the Personal Disc Memory).
If the play does not start
74).
When using the headphones/
earphones connect them directly to
the recorder
The VOL +/– buttons and the Digital Sound
Preset function may become inoperative. In this
case, do the procedure below.
1 Press the jog dial, turn the dial until
“AUDIO OUT” flashes in the display, and
then press the dial again.
2 Turn the jog dial until “HeadPhone” flashes
in the display.
3 Press the jog dial again.
z
• The playback mode will switch automatically
to match the recording mode of the material
(SP stereo, LP2 stereo, LP4 stereo, or
monaural).
• To play only the tracks in a certain group, see
• The volume setting can be stored to the
Note
If the power supply is disrupted (i.e. the battery
is removed or becomes exhausted or the AC
power adaptor is disconnected) when the
recorder is operating, the lid may not open until
the power is restored.
26
Various ways of recording
Two ways of connecting to a sound source
The input jack of this recorder works as both digital and analog input jacks. Connect the
recorder to a CD player or a cassette recorder using either digital (optical) input or analog
record using analog (line) input.
Difference between digital (optical) and analog (line) inputs
Difference Digital (optical) input
Analog (line) input
Connectable Equipment with an digital (optical)
Equipment with an analog (line)
output jack
source
output jack
Usable cord Optical cable (with an optical or an
optical-mini plug) (page 22)
Line cable (with 2 phono plugs
or a stereo-mini plug) (page 28)
Signal from Digital
the source
Analog
Even when a digital source (such
as a CD) is connected, the signal
sent to the recorder is analog.
Recorded
track
numbers
Marked (copied) automatically
• at the same positions as the source
(when the sound source is a CD or an
MD).
Marked automatically
• after more than 2 seconds of
blank or low-level segment.
• when the recorder is paused
while recording.
• automatically at specified
intervals when the Auto Time
Stamp is on.
You can erase unnecessary marks
after recording (“Erasing a track
• after more than 2 seconds of blank or
low-level segment (with a sound
source other than a CD or an MD).
• when the recorder is paused during
synchro-recording (the recorder
pauses automatically when it
encounters a section with no audio
signal for 3 seconds or more).
You can erase unnecessary marks after
recording. (“Erasing a track mark”,
Recorded
sound level
Same as the source.
Adjusted automatically. Can also
be adjusted manually (“Adjusting
Can also be adjusted manually (Digital
Note
Track marks may be copied incorrectly:
• when you record from some CD players or multi disc players using digital (optical) input.
• when the source is in shuffle or program play mode while recording using digital (optical) input. In
this case, play the source in normal play mode.
• when recording BS or CS programs through digital (optical) input.
27
1 Insert a recordable MD, and then
Recording with analog
input (line cable
required)
press and slide REC to the right.
“REC” and the REC indicator on the
recorder light up in the display and
the recording starts.
The sound will be sent from the
connected equipment as analog signal but
will be recorded digitally on the disc.
To connect to a sound source, an optional
line cable is required. When connecting
the cable, make sure to insert the
connectors firmly.
2 Play the source you want to record.
For other recording operations, see
z
LINE IN (OPT) jack is for both digital and
analog input.
The recorder automatically recognizes the type
of line cable and switches to digital or analog
input.
CD player,
cassette recorder,
etc. (source)
Note
to LINE OUT
If you temporarily stop a recording operation
by pressing X, a track mark will be added at
that point when you press X again to resume
recording. The recording continues from on a
new track.
R (red)
L (white)
Line cable*
REC
to LINE IN (OPT)
∗ Use the connecting cords without an
attenuator. To connect to a portable CD
player having a stereo mini-jack, use
the RK-G136 connecting cord. For
more information on connecting cords,
28
3) Items selected by the jog dial.
4) When using an 80-minute recordable MD
Long-time Recording
3 Press and slide REC to the right.
4 Play the source you want to record.
To stop recording, press x.
The recorder switches back to stereo
Select each recording mode according to
the recording time that you want.
Stereo recording is possible at 2 times
(LP2) or 4 times (LP4) the normal (SP
stereo) recording time. Monaural
recording at 2 times normal recording
speed is also possible.
recording when you record the next time.
MDs recorded in monaural, LP2, or
LP4 mode can be played back only
on MD players or recorders with
monaural, LP2, or LP4 playback
mode.
When you do not want “LP:”
added automatically at the
beginning of a track
REC
When “LP:” is added to the beginning of a
track, “LP:” is displayed whenever an
attempt is made to play or edit the disc on
a unit that does not support MDLP mode.
This display lets you know that playback
or editing of the track is not possible on
the machine being used. The recorder is
factory set to add “LP:” (“Stamp ON”) at
the start of each track.
Jog dial
If you do not want “LP:” to be added at
the beginning of tracks, do the procedure
below.
1 Press the jog dial, turn the dial until
“REC MODE” flashes in the display,
and then press the dial again.
2 Turn the jog dial to select the desired
1 While the recorder is stopped, press
the jog dial, turn the dial until
recording mode.
“OPTION” flashes in the display, and
then press the dial again.
Recording Display
Recording
time4)
mode1)
window
on the
2 Turn the jog dial until “LP Stamp”
flashes in the display, and then press
the jog dial.
recorder3)
SP stereo
SP
approx. 80
min.
3 Turn the jog dial until “Stamp OFF”
flashes in the display, and then press
the jog dial.
LP2 stereo LP2
LP4 stereo LP4
Monaural2) MONO
approx. 160
min.
approx. 320
min.
If you want “LP:” added, select
“Stamp ON” in step 3, and then press
the jog dial.
approx. 160
min.
1) For better sound quality, record in normal
stereo (SP stereo) or LP2 stereo mode.
2) If you record a stereo source in monaural, the
sounds from left and right will be mixed.
29
z
• If you set the recorder so that “LP:” is not
added at the beginning of the track, you will
be able to enter longer track names by using
• Audio components that support the LP2 stereo
or LP4 stereo modes are indicated by the
Recording tracks using
the Group Function
(Group mode recording)
GROUP
./
>/x
or
logo marks.
• You can achieve high sound quality and rich
tones when recording in SP stereo (or
monaural) thanks to the newly developed DSP
TYPE-R for ATRAC (Adaptive TRansform
Acoustic Coding).
What is the newly developed DSP
TYPE-R for ATRAC?
END SEARCH
REC
DISPLAY
“TYPE-R” is a high-level Sony specification
used in the Digital Signal Processor (DSP),
which is heart of the MiniDisc sound. This
technology gives the MiniDisc recorder twice
the signal processing capability as previous
MiniDisc Walkman models, producing a
sound quality close to that of MiniDisc decks.
Control
x
Notes
• It is recommended that you use the supplied
AC power adaptor for long recordings.
• During monaural recording of a stereo sound
source connected through the digital (optical)
input jack, you can still monitor the recorded
sound in stereo by using headphones or
earphones connected to the i/LINE OUT
jack.
• When you record in LP4 mode, momentary
noise may be produced on very rare occasions
with certain sound sources. This is because of
the special digital audio compression
technology that enables a recording time 4
times longer than normal. If noise is produced,
it is recommended that you record in normal
stereo or LP2 mode to obtain better sound
quality.
What is the group function
(group mode)?
It is a function that allows you to separate
tracks on a disc into different groups for
playback, recording and editing.
When the Group mode is OFF.
Disc
Track number
1 2 3 4 5 6 7 8 9
When the Group mode is ON.
Disc
Group 1
Group 2
Track
Group 3
Track
Track
number
number number
1 2 3 1 2 1 2 3 4
30
It is convenient for managing multiple
CD albums recorded in MDLP (LP2
stereo/LP4 stereo) mode onto a single
MD.
To activate the group mode
To record tracks in group mode, you must
first turn the group mode on before the
start of recording.
How is group information
recorded?
On the recorder
When recording in group mode, the group
information is written to the disc name
recording area.
This information consists of text strings
that are written as shown in the following
example.
1 Press GROUP for 2 seconds or more.
“
” lights up and the group mode
turns on.
To cancel the group mode, press
GROUP for 2 seconds or more again.
Disc name recording area
Example
On the remote control
1 Press DISPLAY for 2 seconds or
more, turn the control towards .
or N> until “GROUP” flashes in
the display, and then press x.
1
2
3
1 Disc name: “Favorites.”
2 Group name for tracks 1 to 5: “Rock”.
2 Turn the control towards . or
N> until “GROUP ON” flashes
in the display, and then press x.
3 Group name for tracks 6 to 9: “Pops”.
Therefore, the above character string is
displayed in its entirety as the disc name
if you load an MD recorded in group
mode into a system that does not support
group mode, or if you try to edit the
contents of a disc on this recorder with the
group mode turned off.
“G” lights up in the display.
To cancel the group mode, select
“GROUP OFF” in step 2.
Recording a track into a new
group
Note that if you perform the
this character string by mistake,
you may be unable to use the
group function of that MD.
1 While the recorder is stopped, press
GROUP for 2 seconds or more.
2 Press END SEARCH.
3 Press and slide REC to the right.
4 Play the source sound.
Notes
• The group function setting is stored even if
you eject the MD or turn off the recorder.
• In group mode, the recorder treats all tracks
without group settings as belonging to the last
group on the disc. The last group is indicated
in the display window on the recorder as
“Group --”. Within a group, the tracks appear
in their order on the disc, not their order
within the group.
To stop recording, press x.
The material that was recorded up until x
was pressed is entered as a new group.
31
Recording a track into an
existing group
To start/stop recording
in sync with the source
player
1 While the recorder is stopped, press
(Synchro-recording)
GROUP for 2 seconds or more.
You can easily make digital recordings of
a digital source on an MD.
Before synchro-recording, make
connections to the digital source with a
digital cable, and insert a recordable MD.
2 Press GROUP slightly.
“
” flashes in the display and you
can select a group directly (group
3 Within 5 seconds, press . or >
repeatedly until the group you want
the track to belong to appears.
CD players,
etc.
4 Press and slide REC to the right.
5 Play the source sound.
Notes
• Even if “REC-Posi” is set to “From Here”,
newly recorded tracks are inserted after the
existing tracks in the specified group without
recording over the current contents.
• The group skip mode turns off automatically
Jog dial
REC
z
To add a track that is playing to a group, stop
playing the track first, and then do the
x
1 While the recorder is stopped, press
the jog dial, turn the dial until “SYNC
REC” flashes in the display, and then
press the dial again.
2 Turn the jog dial until “SYNC ON”
flashes in the display, and then press
the dial.
007
30:03
Synchro-recording indication
32
• Synchro-recording cannot be done if the
connecting cord is not an optical cable, or if
the cable is connected to the MIC (PLUG IN
POWER) jack.
“SYNC” appears in the display.
“SYNC” does not appear if optical
cable is not connected to the recorder.
• You cannot change the recording mode during
recording.
3 Press and slide REC to the right.
The recorder stands by for recording.
4 Play the source sound.
The recorder starts recording when it
receives the playing sound.
Recording without
overwriting existing
material
To stop recording
Press x.
If you wish to avoid recording over the
current contents of an MD, do the
following procedure. All new material
will then be recorded from the end of the
current contents. The recorder is factory
set to record over existing material.
To cancel synchro-recording
Follow the procedure until “SYNC OFF”
press the jog dial.
Jog dial
z
• When there is no sound from the player for
about 3 seconds during synchro-recording, the
recorder goes into the standby mode
automatically. When the sound comes from
the player again, the recorder resumes
synchro-recording. If the recorder is kept in
the standby mode for 5 minutes or longer, the
recorder stops automatically.
recording mode, and then start the procedure
of synchro-recording.
1 While the recorder is stopped, press
the jog dial, turn the dial until
“OPTION” flashes in the display, and
then press the dial again.
Notes
2 Turn the jog dial repeatedly until
“REC-Posi” flashes in the display,
and then press the dial.
• The pause function cannot be turned on or off
manually during synchro-recording. Press x
to stop recording.
3 Turn the jog dial repeatedly until
“From End” flashes in the display,
and then press the dial.
• Do not switch the “SYNC REC” setting while
recording. Recording may not be done
properly.
• Even when there is no recorded sound on the
sound source, there may be cases when
recording does not pause automatically during
synchro-recording due to the noise level
emitted from the sound source.
To start recording over the
current contents
• If a silent portion is encountered for
approximately 2 seconds during synchro-
recording from a sound source other than a
CD or an MD, a new track mark is
automatically added at the point where the
silent portion ends.
33
z
To stop recording
To temporarily record without recording over
the current contents, press END SEARCH
before the start of recording. The recording will
begin after the last track, even if “REC-Posi” is
set to “From Here” (factory setting). The
remaining recordable time on the disc will
appear in the display when you press END
SEARCH.
Press x.
z
For more information on stereo microphones,
To select microphone
sensitivity
Notes
• The setting will remain even after the power is
turned off.
1 While the recorder is recording or
• If you start recording while the recorder is in
play-pause mode, the recording will begin
from the point at which it is paused.
• When the group mode is turned on, recording
always starts after the current contents.
stopped, press the jog dial.
2 Turn the jog dial until “MIC SENS”
flashes in the display, and then press
the jog dial.
3 Turn the jog dial until “SENS HIGH”
or “SENS LOW” appears in the
display.
Recording from a
microphone
When recording a soft or a sound in
the distance, set to “SENS HIGH”.
When recording a loud or a sound at
close range, set to “SENS LOW”.
Stereo
microphone
(not supplied)
4 Press the jog dial.
Notes
• You cannot record through the microphone
while an optical cable is connected to the
LINE IN (OPT) jack. In this case, disconnect
the optical cable from the LINE IN (OPT)
jack. The recorder automatically switches
input in the following order; optical input,
microphone input, and analog input.
REC
• The microphone may pick up the operating
sound of the recorder itself. Use the
microphone away from the recorder in such
cases. Do not use a microphone with a short
connector, as this may cause the operating
sound of the recorder to be picked up.
to MIC (PLUG IN POWER)
1 Connect a stereo microphone to the
MIC (PLUG IN POWER) jack.
The recorder changes to microphone
input automatically.
2 Insert a recordable MD, and then
press and slide REC to the right.
For other operations, see “Recording
34
Using Auto Time Stamp to add
track marks while recording
Adding track marks
automatically at
the recorder will begin adding a track
mark whenever the time interval has
elapsed. For example, if an Auto Time
Stamp interval of 5 minutes is set, and 8
minutes of recording has already been
done, then a track mark will be added at a
point equivalent to 13 minutes (8 + 5)
after the start of recording, and every 5
minutes thereafter.
specified intervals
(Auto Time Stamp)
Use this feature to add track marks
automatically at specified intervals when
recording through the analog input
connector or a microphone.
Jog dial
If, however, the Auto Time Stamp interval
is longer than the elapsed recording time,
then a track mark will be added when the
Auto Time Stamp interval has elapsed.
For example, if the Auto Time Stamp
interval is set at 5 minutes, but only 3
minutes of recording has been done, then
a track mark will be added at the 5-minute
point after the start of the recording, and
every 5 minutes thereafter.
1 While the recorder is recording or in
recording pause, press the jog dial.
2 Turn the jog dial until “TIME
MARK” flashes in the display, and
then press the dial.
z
“T” appears before the time display on the
recorder for track marks added by Auto Time
Stamp, and “T” appears after the time display
on the remote control.
3 Turn the jog dial until the desired
time interval flashes in the display.
Select one of the following intervals.
Notes
Display
Time
• Automatic track marking by Auto Time Stamp
starts when you add a normal track mark to
the disc (i.e., by pressing T MARK or X,
etc.).
• The setting will be lost when the recording
stopped.
OFF
—
5 min. ON
10 min. ON
15 min. ON
Approx. 5 min.
Approx. 10 min.
Approx. 15 min.
4 Press the jog dial.
To cancel Auto Time Stamp
jog dial, or stop recording.
35
Set the level so that the meter
Adjusting the recording
level manually (Manual
recording)
segments light up between A and B.
If B lights up, reduce the input level.
Each level meter shows the following.
Upper — L channel input level
Lower — R channel input level
When you record, the sound level is
adjusted automatically. If necessary, you
can set the recording level manually (with
the Digital REC level control) during both
analog and digital recording.
004
REC 23/30
REC
X
A
B
Recording does not start in this step.
If your source is an externally
connected component, be sure to cue
the source to the beginning of the
material to be recorded before you
start playback.
Jog dial
6 Press X again to start recording.
1 While holding down X, press and
slide REC to the right.
To switch back to automatic
level control
The recorder stands by for recording.
2 Press the jog dial, turn the dial until
“RecVolume” flashes in the display,
and then press the dial again.
Select “Auto REC” in step.
z
You can adjust the recording level manually
even during recording.
3 Turn the jog dial repeatedly until
“ManualREC” flashes in the display,
and then press the dial.
Notes
• If you press x during recording operation, the
recorder will revert to automatic recording
level adjustment mode the next time you start
a recording operation.
• “RecVolume” cannot be selected in step 2
level manually during synchro-recording, do
the procedure below.
1 Select “SYNC OFF” in step 2 of “To start/
step 1, and select “SYNC ON” in step 2 of
(page 32).
Auto REC
ManualREC
To switch back to the automatic
control, follow the procedure from
until “Auto REC” flashes in the
display, and then press the dial.
4 Play the source.
5 While observing the level meter in the
display, adjust the recording level by
turning the jog dial.
Recording starts automatically whenever
the source sound is played.
36
Note
Items may not be selectable depending on the
group mode’s on/off status or the recorder’s
operating status.
Checking the remaining
time or the recording
position
3 Press the jog dial.
You can check the remaining time, track
number, etc. when recording or during
stop. Group-related items appear only
when a track with group settings is played
and then stopped.
The display changes as follows.
C in the display. If you select
appear on C in this step.
Display window on the recorder
On the recorder
A
B
C
REC indicator
Display A/B/C
A
B
C
Track
number
Elapsed
time
—
Jog dial
(LapTime)
Track
number
Remaining RecRemain
time for
recording
1 Press the jog dial, turn the dial until
“DISPLAY” flashes in the display,
and then press the dial.
Numbers of Remaining GP Remain
2 Turn the jog dial until the information
tracks after
the current
time after
the current
you want flashes in the display.
The display changes as follows.
tracks in the location
group
within the
group
LapTime (The elapsed time of the
current track.)
Numbers of Remaining AllRemain
r
tracks after
the current
track
time after
the current
location
RecRemain (The remaining time
after the current track in the
group.)
Current date Current
time
Clock
r
GP Remain (The remaining time
after the current track in a group.)
r
AllRemain (The remaining time
after the current track.)
r
Note
Items may appear differently depending on the
group mode’s on/off status, the recorder’s
operating status, or the recorder settings.
z
Clock (Current time.)
The display that appears on the remote control
is different from the ones on the recorder. See
“On the remote control” (page 38) to check the
display that appears on the remote control.
37
Display window on the remote control
To know the recording
condition
The indicator lights up or flashes
D
E
according to the recording condition.
Recording
condition
REC indicator
Indication D/E
While recording
lights up
While recording
Track number/Elapsed time
flashes according
to the loudness of
the source while
recording with a
microphone (voice
mirror)
r
Track number/Remaining time for
recording
r
—/Current time
Recording standby flashes
In stop mode
Track number/Elapsed time
Less than 3
minutes’
flashes slowly
r
recording time
available
Track number/Track name
r
Number of tracks in the group/
Group name
A track mark has goes off
been added (when momentarily
controlling by the
r
recorder only)
—/Disc name
r
—/Current time
z
If you want to check the playing position or
Note
Items may appear differently or may not be
selectable, depending on the group mode’s on/
off status, the recorder’s operating status, or the
recorder settings.
On the remote control
DISPLAY
z
• If you want to check the playing position or
• The display that appears on the recorder is
different from the ones on the remote control.
display that appears on the recorder.
1 Press DISPLAY while recording or in
stop mode.
Each time you press the button, the
display changes as follows.
38
If you make a mistake while
setting the clock
Press CANCEL, and set the clock again
pressing the jog dial.
Setting the clock to
stamp the recorded
time
To stamp the date and time on the MD
when you record, you first need to set the
clock.
Once you set the clock, the recorder will
include a time stamp each you record
something. If you don’t want to include a
time stamp on the track, skip this
operation.
To display the current time
When the recorder is not operating or
while recording, press the jog dial, turn
the dial until “DISPLAY” appears in the
display, and then press the dial again.
Turn the jog dial until “Clock” flashes in
the display, and then press the dial again.
The current time appears in the display.
Jog dial
To display the time in the 24-
hour system
While setting the clock, press T MARK.
To display the time in the 12-hour system,
press T MARK again.
To maintain the correct time
1 Press the jog dial while the recorder is
Once you set the clock, it will keep correct time
as long as the recorder is connected to a power
source, such as the rechargeable battery,
alkaline dry battery, or AC power adaptor.
However, if no power source is connected, the
clock setting will change back to the factory
setting after about 3 minutes.
When changing the rechargeable battery or
alkaline dry battery, make sure to do it within 3
minutes.
stopped.
2 Turn the jog dial until “OPTION”
flashes in the display, and then press
the dial.
3 Turn the jog dial until “CLOCK SET”
flashes in the display, and then press
the dial.
The digits of the year flash.
Notes
• Make sure the time is correctly set if you want
the time stamp to be accurately recorded for
an important recording.
• Under normal conditions, the clock may vary
by about plus or minus 3 minutes per month.
01y 1m 1d
12:00am
Clock
4 Change the current year by turning
the jog dial, and then press the dial.
The digit of the month flashes.
month, date, hour, and minute.
When you press the jog dial to enter
the minute, the clock starts operating.
39
1 Press and slide REC to the right to
start recording on the recorder, and
start playing the CD in the portable
CD player.
Copying CD text
information while
recording (Joint Text)
“SYNC” and “REC” light up in the
display.
“CD TEXT” appears for a few
seconds, then “001 TEXT?” appears
and “PushENTER” flashes in the
display.
CD text connecting cable,
CD that support CD-TEXT,
and CD player that support
Joint Text required
“NO TEXT” appears at this time if no
track name information exists in the
CD. In this case, the track name will
not be copied.
By connecting the recorder to a Sony
portable CD player that supports Joint
Text (the CD text copying function) (D-
E999, etc.), you can copy track and disc
names automatically during recording. In
addition to the CD text connecting cable
(RK-TXT1), make sure to connect the
recorder to the portable CD player with an
optical cable.
2 Press the jog dial.
Track name scrolls, and then the track
name appears and “PushENTER”
flashes in the display.
3 Press the jog dial.
x
Jog dial
REC
Track name scrolls in the display
while the name is copied.
new track name that appears.
To LINE IN
(OPT) jack
5 Press x on the recorder at the point
you want to stop recording.
“000 TEXT?” appears and
To i/LINE OUT jack
“PushENTER” flashes in the display.
If you don’t want to copy the disc
name information, press x again. The
disc name is not copied and the
operation ends.
“NO TEXT” appears at this time if no
disc name information exists in the
CD. In this case, the operation ends
without copying the disc name.
RK-TXT1
(not
supplied)
To i/
REMOTE
jack
Portable CD player
(D-E999, etc.)
To LINE OUT
(OPTICAL)
jack
6 Press the jog dial.
Disc name scrolls, and then disc name
appears and “PushENTER” flashes in
the display.
POC-15B etc.
(not supplied)
7 Press the jog dial.
“TOC Edit” flashes.
Afterwards, the disc name scrolls in
the display.
40
z
Notes
If the disc or track name appears in the display
information on some CDs are automatically
recorded from start to finish. If the CD is this
type, press x on the recorder at the point you
want to stop recording, or after all tracks have
been recorded. “TOC Edit” flashes. Afterwards,
the disc name scrolls in the display.
• The CD text copying function can only be
used with components with the logo shown
below.
Audio components that support
the CD text copying function:
D-EJ01, D-EJ925, D-EJ915, D-EJ825,
D-EJ815, D-EJ725, D-EJ721, D-EJ715,
D-EJ711, D-FJ75TR (Aug. 2001)
Notes
• If you copy disc name information to a disc
with a previously recorded disc name, the old
disc name will be overwritten with the new
one.
• When the CD text copying function is on,
various settings and editing functions cannot
be accessed with the jog dial.
• The CD text copying function can only be
used with CDs that support CD-TEXT.
• To record CD text information as a single
group using the CD text copying function,
turn the group mode on before step 1
(page 31). The disc name will be copied as the
name of the group.
• The RK-TXT1 CD text connecting cable is
designed for exclusive use with this recorder
and Sony portable CD player (D-E990, etc.).
Do not use a connecting cable of another
make to copy CD text information.
• The remote becomes inoperative when the CD
text connecting cable (RK-TXT1) is
connected to the recorder.
• Stopping or pausing playback on the CD
player automatically causes recording on the
recorder to pause. A new track mark is
automatically added when you resume
recording.
z
You can monitor the sound during recording.
Connect the headphones/earphones with remote
control on to the CD text connecting cable and
adjust the volume by pressing the VOL +/–
buttons on the recorder.
• The track name of the track currently played
will not be recorded if you stop or pause CD
playback in the middle of the copying process
on the recorder.
• The name of the source CD is copied as the
name of the disc when group mode is off, and
as the name of a group when group mode is
on.
Connect the headphones/earphones
with remote control
41
Various ways of playback
Searching for a specific track
Searching for a specific
track or a position
while monitoring track
numbers or track names
(Index Search)
quickly (Quick Search)
./>/X
To do an index search, do the procedures
“Selecting the search mode” and select
On the recorder
1 Turn the jog dial until the desired
track appears in the display, and then
press the dial.
Jog dial
DISPLAY
X
The selected track name appears in
the display and the recorder starts
playing by pressing the jog dial.
If the track has no name, the track
number appears in the display.
Control
x
On the remote control
You can do two kinds of quick search.
• Index search — Searching quickly while
monitoring the track numbers or track
names.
• Time search — Searching quickly while
monitoring the elapsed time.
1 Press X while playing a disc.
The playback will pause.
2 Turn and hold the control towards
. or N> until the desired
track number or track name appears
in the display.
Selecting the search mode
3 Press X to cancel the pause.
The search mode can be selected only on
the remote control while the recorder is
stopped, playing, or play-paused.
Playback starts from the selected
track.
z
1 Press DISPLAY for 2 seconds or
• If you do the procedures while the recorder is
shuffling the tracks, shuffle play starts from
the track that you selected.
• If the recorder reaches to the first or the last
track on the disc as you are turning the jog dial
or the control, it will return to the last track or
the first track, respectively.
more.
2 Turn the control towards . or
N> until “SEARCH” flashes in
the display, and then press x.
3 Turn the control towards. or
N> until “Index”(index search)
or “Time”(time search) flashes in the
display, and then press x.
The recorder is factory set to “Index”.
42
Searching for a specific point
while monitoring the elapsed
time (Time Search)
To do a time search, do the procedures of
“Selecting the search mode” and select
Using the Group
Function (Group mode)
The recorder can operate various
playback with a disc which has group
setting. For more information on the
group mode, see “Recording tracks using
On the recorder
GROUP
1 Press X while playing a disc.
The playback will pause.
2 Keep pressing . or > until the
desired point appears in the display.
3 Press X to cancel the pause.
Playback starts from the selected
point.
Jog dial
DISPLAY
On the remote control
PLAYMODE
1 Press X while playing a disc.
The playback will pause.
2 Turn and hold the control towards
. or N> until the desired
point appears in the display.
Control
x
3 Press X to cancel the pause.
Listening to tracks in a
specific group (group mode
playback)
Playback starts from the selected
point.
z
On the recorder
• If you do the procedures while the recorder is
shuffling the tracks, shuffle play starts from
the track that you selected.
1 Insert a disc which has group settings
• If you reach the first or the last track on the
disc while turning the jog dial or the control
during a time search, the recorder will pause
at beginning of the first track or the last track,
respectively.
into the recorder and play the disc.
2 Press GROUP for 2 seconds or more.
“
” and “GROUP ON” light up in
the display and the group mode turns
on.
Playback stops at the end of the last
track in the selected group.
For details on selecting another
group, see “Selecting and playing
43
Note
On the remote control
In group mode, the recorder treats all tracks
without group settings as belonging to the last
group on the disc. The last group is indicated in
the display window on the recorder as
“Group --”. Within a group, the tracks appear in
their order on the disc, not their order within the
group.
1 Insert a disc which has group settings
into the recorder and play the disc.
2 Press DISPLAY for 2 seconds or
more, turn the control towards .
or N> until “GROUP” flashes in
the display, and then press x.
Selecting and playing desired
groups (Group skip mode)
With a disc which has group settings, you
can skip from the currently playing group
to any other group on the disc. You can
select a desired group directly using the
jog dial on the recorder.
3 Turn the control towards . or
N> until “GROUP ON” flashes
in the display, and then press x.
The elapsed time of the track and “G”
(group mode) appears in the display
and then group mode turns on.
Playback stops at the end of the last
track in the selected group.
For details on selecting another
group, see “Selecting and playing
On the recorder
1 Insert a disc which has group settings
into the recorder and play the disc,
and then press GROUP slightly.
z
• You can also change the playback mode
(repeat play, shuffle play, or program play) in
the selected group. After the procedures here,
follow the steps of “Changing a play mode”
“
” flashes in the display and the
group skip mode turns on.
2 Within 5 seconds, turn the jog dial to
select your desired group, and then
press the jog dial.
• In group mode, pressing > on the recorder
or N> on the remote control during the
last track of the group moves playback to the
first track of the group, and pressing . on
the recorder or the remote control during the
first track of the group moves playback to the
last track of the group.
The recorder starts playing from the
first track in the group.
z
You can also select a group using the ./>
buttons in step 2.
• The settings can be stored to the Personal Disc
On the remote control
To turn off the Group function
On the recorder, press GROUP for 2
seconds or more again.
1 Insert a disc which has group settings
into the recorder and play the disc.
On the remote control, select “GROUP
2 Press and hold PLAYMODE until “–
– –” flashes in the display.
The group skip mode turns on.
44
3 Within 5 seconds, turn the control
towards . or N> to select
your desired group.
2 Turn the jog dial to select the play
mode, and then press the dial.
Each time you turn the dial, the
display item indicated by A changes
as shown below.
Pressing the jog dial while the item is
flashing changes its play mode.
The new mode then appears in the
window indicated by B.
During playback on group mode,
playback of the desired group starts
with the first track in the group and
stops with the last track in the group.
During normal playback, playback of
the selected group starts with the first
track in the group and stops with the
last track on the disc.
indicates that repeat play has been
activated for playback.
Notes
Display window on the recorder
• If no operation is performed within 5 seconds
canceled and you will not be able to perform
this point, repeat from the beginning of the
procedure.
When you turn the jog dial, A changes.
A
Shuffle
Shuf.Rep
PGM
• The group skip mode cannot be used with a
disc that has no group settings.
z
When you press the jog dial, B appears.
The group skip mode operates regardless of
whether the group mode is on or off.
B
003
20:51
Changing a play mode
You can play tracks repeatedly in three
ways — all repeat, single repeat, and
shuffle repeat.
On the recorder
Jog dial
Selecting a play mode
1 While the recorder is playing, press
the jog dial, turn the dial until “PLAY
MODE” flashes in the display, and
then press the dial again.
continued
45
Indication A/B (Play mode)
5 Press the jog dial for 2 seconds or
Normal/— (All the tracks are
more.
played once.)
The program is set and the playback
starts from the first track.
r
AllRepeat/
played repeatedly.)
(All the tracks are
z
• The program play setting will be remain in
memory even after playback finished or is
stopped.
r
1 Track/1 (A single track is
played.)
• You can set the program play up to 20 tracks.
• The settings can be stored to the Personal Disc
r
1 Repeat/
1 (A single track is
played repeatedly.)
r
Shuffle/SHUF (After the
currently selected track finishes
playing, the remaining tracks are
played in random order)
r
• You can specify the playback mode for a
selected group when the group mode is on. To
activate the group mode, see “Selecting and
• The play mode can also be selected when the
recorder is stopped.
Shuf. Rep/
SHUF (After the
currently selected track finishes
Notes
• All program settings are lost when the lid of
the recorder is opened.
playing, the remaining tracks are
• If the recorder is stopped and left inactive for
5 minutes in the middle of a programming
operation, the tracks selected up to that point
are entered as the program.
• If you try to switch the group mode on or off
while programing tracks, “SORRY” appears
in the display and the group mode does not
change.
played repeatedly in random
order.)
r
PGM/PGM (Tracks are played in
the order that you specified.)
r
PGMRepeat/
PGM (Tracks
• If you turn the group mode on during program
play, the program setting is canceled.
are played repeatedly in the order
that you specified.)
Creating a Program (Program
play)
On the remote control
You can select various play mode using
the PLAYMODE and RPT/ENT buttons
on the remote control.
1 Press the jog dial while “PGM”
flashes in the display in step 2 of
PLAYMODE
RPT/ENT
2 Turn the jog dial to select a track.
3 Press the jog dial to enter a track
number.
tracks.
Control
46
Selecting a play mode
5 Press RPT/ENT for 2 seconds or
more.
1 Press PLAYMODE while the
recorder is playing.
Repeat play
Each press of the button changes the
play mode indication as shown below
and starts playback in the selected
play mode.
1 Press RPT/ENT during playback.
“
” appears in the display and the
recorder plays as the selected play
mode repeatedly.
Display window on the remote control
z
Play mode indication
• The program play setting will be remain in
memory even after playback finished or is
stopped.
• You can set the program play up to 20 tracks.
• The settings can be stored to the Personal Disc
• You can specify the playback mode for a
selected group when the group mode is on. To
activate the group mode, see “Selecting and
Indication (Play mode)
— (All the tracks are played once.)
r
1 (A single track is played.)
r
SHUF (After the currently
selected track finishes playing, the
remaining tracks are played in
random order)
• The play mode can also be selected when the
recorder is stopped.
Notes
r
• All program settings are lost when the lid of
the recorder is opened.
• If the recorder is stopped and left inactive for
5 minutes in the middle of a programming
operation, the tracks selected up to that point
are entered as the program.
• You cannot switch the group mode on or off
while programming tracks.
• If you turn the group mode on during program
play, the program play is canceled.
PGM (Tracks are played in the
order that you specified.)
Creating a Program (Program
play)
1 While the recorder is playing, press
PLAYMODE repeatedly until “PGM
” flashes in the display.
2 Turn the control towards . or
N> to select a track number.
Track
number
Program number
3 Press RPT/ENT to enter a track
number.
tracks.
47
On the remote control
1 Press SOUND repeatedly to select
“SOUND 1” or “SOUND 2” appears in
the display.
To adjust the sound
quality (Digital Sound
Preset)
You can make adjustments to the sound
quality to suit your taste, and then store
two sets of these adjustments.
Adjusting the sound quality
On the recorder
x/X
1 While playing, press the jog dial, turn
the dial until “SOUND” flashes in the
display, and then press the dial again.
2 Turn the jog dial until “SOUND 1” or
“SOUND 2” flashes in the display.
Jog dial
SOUND
The display shows the currently
selected “T” (treble) and “B” (bass)
sound setting.
Select “T” or “B” pressing x (to
move the cursor downward) or X (to
move the cursor upward).
You can change the adjust the item in
which the cursor is flashing.
Control
x
SOUND 1
T-=== ==+
B-==== =+
Selecting the sound quality
Factory settings of the Digital
Sound Preset
When you adjust treble, select “T”.
When you adjust bass, select “B”.
Factory settings of the Digital Sound
Preset are the followings:
• “SOUND 1”: bass +1, treble
0
• “SOUND 2”: bass +3, treble
0
To select a preset sound
On the recorder
1 Press the jog dial, turn the dial until
“SOUND” flashes in the display, and
then press the dial again.
2 Turn the jog dial until “SOUND 1” or
“SOUND 2” flashes in the display, and
then press the dial.
48
3 Turn the jog dial to adjust the sound
2 During playback, press SOUND for 2
level.
seconds or more.
The recorder changes to B (bass)
setting mode. Pressing the SOUND
button for 2 seconds again changes
the recorder back to T (treble) setting
mode.
The cursor moves. (Position: +2)
SOUND 1
T-===== +
B-== ===+
-4
0
+3
The sound can be adjusted in 8 steps
When you select bass-setting mode,
“B” appears. When you select treble-
setting mode, “T” appears.
(–4, –3, ... 0, ...+2, +3).
Press x to move the cursor from “T”
to “B” (from the middle row to the
bottom row in the display) and press
X to move the cursor from “B” to “T”
(from the bottom row to the middle
row in the display).
3 Turn the control towards . or
N> repeatedly to adjust the bass
or the treble.
Example: While adjusting the bass
To switch between “SOUND 1” to
“SOUND 2”, move the cursor to the
top row by pressing X while the
cursor is flashing on the “T” row, and
then turn the jog dial.
The cursor moves.
(Position: –2)
–4
0
+3
4 Press the jog dial.
The sound can be adjusted in 8 steps
(–4, –3, ... 0, ...+2, +3).
The sound settings are saved and the
playback display appears again.
Pressing the SOUND button for 2
seconds or more toggles the display
between “SOUND 1” and “SOUND
2”. When you press SOUND for a
short time while adjusting B (bass) or
T (treble), the setting for that sound is
entered and the display switches to
the other sound setting.
z
You can also use the . or > buttons to
On the remote control
1 Press SOUND repeatedly to select
“SOUND 1” or “SOUND 2”.
4 Press x.
The sound settings are saved and the
playback display appears again.
To cancel the digital sound preset
• On the recorder
Select “SOUND OFF” in step 2.
• On the remote control
Press SOUND repeatedly until nothing
appears in the display.
49
z
3 Turn the control towards . or
• The settings can be stored to the Personal Disc
N> to select the playback speed.
“+” shows the normal speed and the
cursor shows the playback speed you
are selecting.
• Settings can also be changed while playback
is momentarily paused (X).
• If the recorder is not operated approximately
for 5 minutes, the current setting is stored and
the display automatically switches to normal
play mode.
Example: while the playback speed is
95% of normal.
– and the cursor appear
Notes
alternately in the display.
• Digital Sound Preset becomes inoperative
when the “AUDIO OUT” parameter for the
i/LINE OUT jack is set to “LINE OUT”. In
this case, set the “AUDIO OUT” to
80% 100%
110%
• When you use the Digital Sound Preset, the
sound may break or become distorted
depending on the settings or the track. Tn this
case, charge the settings of the sound quality.
• Changing to another Digital Sound Preset
during a recording operation will not affect
the quality of recorded sound.
4 Press x to set the playback speed.
Display window on the remote control
“S” appears to the right of the elapsed
time during playback speeds other than
normal.
To change playback
speed (Speed Control)
Display window on the recorder
The playback speed can be adjusted in 7
steps (80%, 85%, ...100%, 105%, 110%).
“S” appears to the right
of the track number.
DISPLAY
002
S 03:40
z
The settings can be stored to the Personal Disc
Control
x
Notes
1 Press DISPLAY for 2 seconds or
• You cannot change playback speed with the
recorder.
more during playback.
• The playback sound will be affected by the
playback speed.
• All settings will be lost when you remove the
disc from the recorder (except when the
setting is stored to the Personal Disc
Memory).
2 Turn the control towards . or
N> until “SPEED” flashes in the
display, and then press x.
The recorder changes to speed-setting
mode.
50
On the remote control
Storing the settings for
individual discs
(Personal Disc Memory)
DISPLAY
The recorder can store the various settings
for each disc, and then retrieve them
automatically whenever the disc is
inserted.
The following setting can be stored:
• Volume
Control
x
1 While the recorder is stopped,
• Playback mode
• Group mode playback
• Program play
playing, or play-paused, press
DISPLAY for 2 seconds or more.
• Sound quality (Digital Sound Preset)
• Playback speed (Speed control)
2 Turn the control towards . or
N> until “PERSONAL” flashes
in the display, and then press x.
“Entry?” flashes in the display.
On the recorder
Jog dial
3 Press x.
“Entry OK” appears in the display
and the disc settings are stored in the
recorder.
Erasing the disc information
1 While the recorder is stopped,
playing, or play-paused, press the jog
dial.
Insert the disc whose information is to be
erased and verify its contents. Do steps 1
and then press the jog dial on the recorder
or x on the remote control. “Erase OK”
appears in the display and the disc
information is erased. If you try to erase
the disc information of a disc that have
never been stored, “No Entry!” appears in
the display for 2 seconds.
2 Turn the jog dial until “PERSONAL”
flashes in the display, and then press
the dial.
“Entry?” flashes in the display.
Entry?
Erase?
Notes
• The settings for up to 20 discs can be stored.
Any settings stored afterwards will replace the
settings for the least used disc among the 20.
• If you use another minidisc recorder to edit or
add tracks to a disc whose settings have been
stored on the recorder, the disc will no longer
be recognizable by the recorder and the stored
information will become useless. In this case,
store the settings again.
3 Press the jog dial.
“Entry OK” appears in the display
and the disc settings are stored in the
recorder.
51
Note
Items may appear differently depending on the
group mode’s on/off status or the recorder’s
operating status.
Checking the remaining
time or the playing
position
3 Press the jog dial.
You can check the track name, disc name,
etc. during playback. Group-related items
appear only when a track with group
settings is played and then stopped.
The display changes as follows.
section C in the display. However, if
section C remains blank.
On the recorder
Display window on the recorder
Jog dial
A
B
C
Indication A/B/C
A
B
C
Track
number
Elapsed time
—
1 While the recorder is playing, press
the jog dial, turn the dial until
(LapTime)
Track
number
Remaining
time of the
current track
1 Remain
“DISPLAY” flashes in the display,
and then press the dial again.
2 Turn the jog dial until the information
Number of Remaining
tracks after time after the Remain
the current current
GP
you want flashes in the display.
Each time you turn the dial, the
display changes as follows.
track in the location in the
group
group
LapTime (The elapsed time.)
Number of Remaining
tracks after time after the
the current current
AllRemain
r
1 Remain (The remaining time of
the current track.)
track
location in the
group
r
Recorded Recorded time RecDate
date
GP Remain (The remaining time
after the current location in the
group.)
Note
r
Items may not be selectable depending on the
group mode’s on/off status or the recorder’s
operating status.
AllRemain (The remaining time
after the current location.)
r
z
RecDate (Recording date and
time.)
The display that appears on the remote control
is different from the ones on the recorder. See
“On the remote control” (page 53) to check the
display that appears on the remote control.
52
On the remote control
Connecting to a stereo
system (LINE OUT)
DISPLAY
Connect the i/LINE OUT jack of the
recorder to the LINE IN jacks of an
amplifier or a tape player with a line
cable. For more information on line
cables, see “Optional accessories”
(page 88). The output is analog. The
recorder plays the MD digitally and sends
analog signals to the connected
equipment.
1 Press DISPLAY while playing.
Each time you press DISPLAY, the
display changes as follows.
Display window on the remote control
Portable DAT
recorder
Stereo system,
etc.
D
E
to LINE IN
Stereo mini-plug
2 phono plugs
Indication D/E
Track number/Elapsed time
R
(red)
L
(white)
r
RK-
G129
Track number/Track name
RK-
G136
r
The number of tracks in the group/
Group name
to i/LINE OUT
r
Jog dial
The number of tracks in the disc/
Disc name
r
—/Recorded time
Note
Items may appear differently depending on the
group mode’s on/off status, the recorder’s
operating status, or the recorder settings.
When connecting a line cable to the i/
LINE OUT jack of the recorder, be sure to
set the “AUDIO OUT” parameter for the
i/LINE OUT jack.
z
• If you want to check the remaining time or the
recording position while recording or in stop
mode, see page 38.
• The display that appears on the recorder is
different from the ones on the remote control.
display that appears on the recorder.
1 Press the jog dial, turn the dial until
“AUDIO OUT” flashes in the display,
and then press the dial again.
2 Turn the jog dial until “LINE OUT”
flashes in the display, and then press
the dial.
53
Notes
• If the “AUDIO OUT” parameter for the i/
LINE OUT jack is set to “LINE OUT”, VOL
+/– or Digital Sound Preset will not function.
• The “AUDIO OUT” parameter for the i/
LINE OUT jack cannot be set to “LINE OUT”
when the remote control is connected.
• When you connect the headphones/earphones
directly to the recorder, set the “AUDIO
OUT” parameter for the i/LINE OUT jack to
“HeadPhone”.
54
Editing recorded tracks
• When labeling a disc which has been recorded
using the group function, be sure to turn the
group function on to avoid misoverwrite the
group management information.
You can edit your recordings by adding/
erasing track marks or labeling tracks and
MDs. Premastered MDs cannot be edited.
• If you enter the symbol “//” between the
characters in disc names such as “abc//def”,
you may be unable to use the group function.
Notes on editing
• Do not move or jog the recorder while “TOC
Edit”* is flashing in the display.
• You cannot edit tracks on an MD that is
record-protected. Before editing tracks, close
• If you perform an editing operation while
playing, be sure not to turn the power off until
“TOC Edit” disappears in the display.
• The lid does not open until “TOC Edit”
disappears in the display after editing.
• When the group mode is on, editing can be
performed only for the tracks registered into
the selected group.
About the character palette
The character palette appears in the
display when the recorder is ready to
accept character input.
The character palette has the following
configulation.
∗ TOC = Table of Contents
The character palette will appear in the
display as shown below.
The cursor flashes.
Labeling recordings
You can name tracks, discs and groups
using the recorder’s character palette.
You can name tracks or groups during
playback, discs during stop, and all during
recording. Each name can be as long as
200 letters.
Each disc can hold up to 1,700
alphanumeric letters during playback or
stop.
ABCDEFGHI
abcdefghi
On the recorder
X/x/./>/N
END SEARCH
GROUP/
CANCEL
Available characters
• Capital and small letters of the English
alphabet
• Numbers 0 to 9
• ! " # $ % & ( ) * . ; < = > ?
@ _ ` + – ' , / : _ (space)
VOL +/–
Jog dial
Notes
Labeling a disc during stop
• “NAME FULL” appears when you try to enter
more than 1,700 characters on a disc. Enter a
shorter name for the track, group, or disc, or
set the “LP Stamp” setting to “Stamp OFF”
when recording in MDLP mode so that “LP:”
is not be added at the beginning of the track
To label a disc that contains group
settings, you must turn the group mode on
before doing the labeling procedure.
1 Insert a disc.
continued
55
2 While the recorder is stopped, press
the jog dial, turn the dial until “EDIT”
flashes in the display, and then press
the dial again.
Buttons Functions1)
(Press/
Turn)
N
To enter a letter in the
“
: Name” flashes in the display.
character palette.
To enter the text string in the
letter input area (Press for 2
seconds or more).
3 Press the jog dial.
The disc is ready to be labeled.
Letter input area
VOL +
To insert a blank space
before the cursor in the letter
input area.
To move the cursor to the
right in the character palette.
VOL –
To delete a letter in the letter
input area.
Character palette
To move the cursor to the
left in the character palette.
4 Press x to shift the cursor from the
letter input area to the character
palette.
Jog dial
To select a character in the
letter input area (Turn).
To scroll the character
palette in the palette2)(Turn).
To enter a letter (Press).
To enter a name (Press for 2
seconds or more).
5 Press . or > to select a letter
and press N to enter.
The selected letter appears in the
letter input area and the cursor moves
to the next input position. The buttons
used for character input and their
functions are listed below.
GROUP/ To cancel labeling in the
CANCEL letter input area.
To move the cursor from the
character palette to the letter
input area,
Buttons Functions1)
(Press/
Turn)
T MARK To display “:”, “–” and “/”
repeatedly at the input
position in the letter input
area.
X
To move the cursor from the
character palette to the letter
input area.
To move the cursor upward
in the character palette.
1) Functions of a button may vary, depending on
whether it is used in the letter input area or the
character palette.
x
To move the cursor from the
letter input area to the
character palette.
To move the cursor
downward in the character
palette.
2) If phrases are stored in the name bank, the first
characters of the label name.
./
>
To move the cursor to the
left or right.
7 Press the jog dial for 2 seconds or
more.
The disc is labeled.
56
z
2 To label a track, press the jog dial
You can store phrases that you often use in
while “
: Name” is flashing.
To label a group, turn the jog dial
until “ : Name” flashes in the
display, then press the dial.
Labeling a track or a group
during playback
To label a disc, turn the jog dial until
“
: Name” flashes in the display,
1 To label a track, insert a disc and play
then press the dial.
The track, group, or disc is ready to
be labeled.
the track you want to label.
To label a group, insert a disc, turn the
group mode on, and play the group
2 Press the jog dial, turn the dial until
“EDIT” flashes in the display, and
then press the dial again.
To cancel labeling
Press CANCEL to cause “CANCEL?” to
light up and “PushENTER” to flash in the
display, and then press the jog dial.
“
: Name” flashes in the display.
3 To label a track, press the jog dial
while “
: Name” is flashing.
Notes
• When the recording is stopped while labeling
a track, a group, or a disc during recording, or
when the playback moves on to the next track
while labeling a track, the input at that point is
entered automatically.
• “LP:” is automatically added at the beginning
of the track name for tracks recorded in
To label a group, turn the jog dial
until “ : Name” flashes in the
display, and then press the dial.
The track or group is ready to be
labeled.
Labeling a track, a group, or a
disc during recording
To label a group, you must first turn the
group mode on before the start of
On the remote control
DISPLAY
PLAYMODE
X
1 While recording, press the jog dial,
turn the dial until “EDIT” flashes in
the display, and then press the dial
again.
Control
x
“
: Name” flashes in the display.
Labeling a disc during stop
To label a disc that contains group
settings, you must turn the group mode on
before doing the labeling procedure.
1 Insert a disc.
continued
57
2 Press DISPLAY for 2 seconds or
To cancel labeling
Press DISPLAY for 2 seconds or more.
more while the recorder is stopped.
3 Turn the control towards . or
N> until “EDIT” flashes in the
display, and then press x.
Labeling a track or a group
during playback
“
: Name” flashes in the display.
4 Press x.
The disc is ready to be labeled.
1 To label a track, insert a disc and play
the track you want to label.
To label a group, insert a disc, turn the
group mode on, and play the group
5 Turn the control towards . or
N> to select a letter and press x
to enter.
2 Press DISPLAY for 2 seconds or
more.
The selected letter stops flashing and
the cursor moves to the next input
position.
3 Turn the control towards . or
N> until “EDIT” flashes in the
display, and then press x.
Buttons
(Press/
Turn)
Functions
“
: Name” flashes in the display.
4 To label a track, press x while
X
To switch between
capital letters, small
letters, numbers/marks,
and phrases.1)
“
: Name” is flashing.
To label a group, turn the control
towards . or N> until “GP :
Name” flashes in the display, and
then press x.
Control (VOL To move the cursor to
+/–)
the left or right.
The track or group is ready to be
labeled.
Control
(./
N>)
To change the letter to
the one before/next one.
DISPLAY
To insert a blank space
to type in a new letter.
To cancel labeling by
(Press for 2 seconds or
more).
Labeling a track, a group, or a
disc during recording
To label a group, you must turn the group
mode on before the start of recording
PLAYMODE To delete a letter and
move back all following
letters to the left.
1 Press DISPLAY for 2 seconds or
more during recording.
1)
If phrases are stored in the name bank, the
first phrase stored appears in the display
2 Turn the control towards . or
N> until “EDIT” flashes in the
display, and then press x.
“
: Name” flashes in the display.
of the label name.
7 Keep pressing x for 2 seconds or
more.
The disc is labeled.
58
3 To label a track, press x while
“
: Name” is flashing.
Storing phrases
frequently used in
labeling
To label a group, press the control
towards . or N> until “GP :
Name” flashes in the display, then
press x.
To label a disc, press the control
towards . or N> until
Phrases that you often use in track, group,
or disc labeling can be stored in the
recorder’s memory. There are two ways to
store phrases: storing a phase using the
Name Bank function, or storing a phrase
into the letter palette while performing the
labeling procedure into the letter palette.
Approximately 40 phrases of about 10
characters each (with a total character
count of about 600) can be stored in the
recorder’s memory. The actual number
will depend on the length of each phrases.
“
: Name” flashes in the display,
then press x.
The track, group, or disc is ready to
be labeled.
To cancel labeling
Press DISPLAY for 2 seconds or more.
Notes
On the recorder
• When the recording is stopped while labeling
a track, a group, or a disc during recording, or
when the recording moves on to the next track
while labeling a track, the input at that point is
entered automatically.
./>
END SEARCH
CANCEL
• “LP:” is automatically added at the beginning
of the track name for tracks recorded in
z
Jog dial
You can store phrases that you often use in
Storing phrases into the name
bank (Name Bank function)
Relabeling recordings
Follow the steps corresponding to the
labeling method until the track, group, or
disc is ready to be labeled. Enter a new
character over the one you want to
change, then keep pressing the jog dial for
2 seconds or more on the recorder and
keep pressing x for 2 seconds or more on
the remote control.
1 Press the jog dial, turn the dial until
“EDIT” flashes in the display, and
then press the dial again.
2 Turn the jog dial until “Name Bank”
flashes in the display, and then press
the dial.
Notes
3 Enter the phrase you want to store,
and then press the jog dial for 2
seconds or more.
• You cannot relabel premastered MDs or label
MDs that have not been recorded.
• The recorder is able to display, but cannot
label using Japanese “Katakana” characters.
• The recorder cannot rewrite a disc or track
name of more than 200 letters that was created
by another device.
“Entry!” appears in the display and
the phrase is stored.
59
Searching for a phrase by displaying
the stored phrase one by one
Storing phrases while labeling
a track, group, or disc
recordings” (page 55) to enter a
phrase.
recordings” (page 55), and turn the
jog dial until “
: Name”, or “
: Name”,
: Name”
“
2 After entering the phrase, press
CANCEL to remove the cursor from
the character palette to the letter input
area, and then press END SEARCH
for 2 seconds or more.
flashes in the display. Then press the
jog dial.
2 Press END SEARCH so that the
phrase stored in the recorder’s
memory appears in the display.
“Entry!” appears in the display and
the cursor flashes after the phrase you
just stored. You can then continue
with labeling operation.
3 Press x to move the cursor from the
letter input area to the character
palette, and then turn the jog dial until
the desired phrase flashes in the
display.
z
You can store phrases from a previously labeled
track, group, or disc.
Turning the jog dial causes the
phrases stored in the recorder’s
memory to appear one by one in
sequential order.
Do the procedure “Relabeling recordings”
(page 59) and display the track, group, or disc
name that contains the phrase that you want to
store. Press ./> repeatedly to move the
cursor to the right of the phrase. Then press
END SEARCH for 2 seconds or more to store
the phrase.
4 Press the jog dial while the phrase
you want flashes in the display.
The phrase is selected and lights up in
the letter input area.
Retrieving phrases
You can retrieve a phrase stored in the
recorder’s memory anytime you want to
use it in a track, group, or disc name.
There are two ways to retrieve a stored
phrase: by displaying the stored phrases
one by one during the labeling procedure,
or by searching the name bank by the first
letter of the desired phrase.
5 Press the jog dial for 2 seconds or
more.
The phrase is retrieved.
Searching for a phrase by its first
letter
1 When labeling a track, group, or disc,
turn the jog dial in the letter input
area until the first letter of the desired
phrase appears.
Note
Phrases stored in the name bank cannot be
retrieved by the procedure described in
phrase one by one”. To retrieve a phrase from
the name bank, follow the procedure described
2 Press END SEARCH to search so
that the phrase corresponding to the
letter appears.
3 Press x to move the cursor from the
letter input area to the character
palette, and then turn the jog dial until
the desired phrase flashes in the
display.
60
4 Press the jog dial while the desired
2 Turn the control towards . or
towards N> until “EDIT” flashes
in the display, and press x.
phrase flashes in the display.
The phrase is selected and lights up in
the letter input area.
3 Turn the control towards . or
towards N> repeatedly until
“Name Bank” flashes in the display,
and then press x.
5 Press the jog dial for 2 seconds or
more.
The selected phrase is retrieved.
4 Enter the phrase you want to store,
Erasing phrases
then press x for 2 seconds or more.
“Entry!” appears in the display and
the phrase is stored.
1 While the recorder is stopped, press
the jog dial, turn the dial until “EDIT”
appears, and then press the dial again.
Storing phrases while labeling
2 Turn the jog dial until “BankErase”
(page 57) to enter a phrase.
appears, and then press the dial.
3 Turn the jog dial until the phrase you
want to erase flashes in the display,
and then press the dial.
2 After entering the phrase, press X for
2 seconds or more.
“Erase!” appears and the phrase is
erased.
“Entry!” appears in the display and
the cursor flashes after the phrase you
just stored. You can then continue
with labeling operation.
To cancel the operation
Press CANCEL to cause “CANCEL?”
lights up and “PushENTER” to flash in
the display, and then press the jog dial.
z
You can store phrases from a previously labeled
track, group, or disc.
Do the procedure “Relabeling recordings”
(page 59) and display the track, group, or disc
name that contains the phrase that you want to
store. Pull and turn the control towards VOL +
or VOL – to move the cursor to the right of the
phrase, and then press X for 2 seconds or more.
Then press x for 2 seconds or more to store the
phrase.
On the remote control
DISPLAY
X
Retrieving phrases
Control
Note
x
Phrases stored in the name bank cannot be
retrieved by the procedure described in
phrase one by one”. To retrieve a phrase from
the name bank, follow the procedure described
Storing phrases into the name
bank (Name Bank function)
1 Press DISPLAY for 2 seconds or
more.
61
Searching for a phrase by displaying
the stored phrase one by one
4 Press x while the phrase you want is
shown in the display, and then press
x for 2 seconds or more.
(page 57), and then turn the control
towards . or N> until
The cursor flashes after the phrase
you just retrieved.
Erasing phrases
“
“
: Name”, “GP : Name”, or
: Name” appears in the display.
1 While the recorder is stopped, press
Then press x.
DISPLAY for 2 seconds or more.
2 Press X repeatedly until the phrase
stored in the recorder’s memory
appears in the display.
2 Turn the control towards . or
towards N> until “EDIT” flashes
in the display, and press x.
3 Turn the control towards . or
3 Turn the control towards . or
towards N> repeatedly until
“BankErase” appears in the display,
and then press x.
N> repeatedly.
Turning the control causes the
phrases stored in the recorder’s
memory to appear one by one.
4 Turn the control towards . or
towards N> repeatedly until the
phrase you want to erase appears, and
then press x.
4 Press x slightly while the phrase you
want is shown in the display, and then
press x for 2 seconds or more.
The cursor flashes after the phrase
you just retrieved.
“Erase!” appears in the display and
the phrase is erased.
Searching for a phrase by its first
letter of a phrase
To cancel the operation
Press DISPLAY for 2 seconds or more.
1 When labeling a track, group, or disc,
turn the control towards . or
N> until the letter which the
desired phrase begins with flashes in
the display.
2 Press X to search so that the phrase
corresponding to the letter appears.
3 Turn the control towards N>until
the desired phrase flashes in the
display.
Turning the control causes all the
other phrases stored in the name bank
appear one by one.
After all the phrases have appeared,
the characters in the character palette
appear in the display one by one.
62
2 Turn the jog dial until “
: Set”
Registering tracks or
groups as a new group
(Group setting)
flashes in the display, and then press
the jog dial.
“001” flashes in the display.
Do the following procedure to register
tracks (or groups). A series of tracks (or
groups) can be registered by selecting the
starting and ending tracks (or groups).
The tracks (or groups) must, however, be
sequential. If the desired tracks (or
groups) are not consecutive, you must
move them to make them consecutive
before you can register them (“Moving
recorded tracks”, page 64). This function
can be used at any time, whether group
mode is on or off.
STR:001
END:001
:
3 Turn the jog dial until the number or
name of the desired first track flashes
in the display, and then press the jog
dial.
This selects the first track of the new
group.
Even when the group mode is on,
track numbers appear according to
their order on the disc, not their order
within the group.
Group
Group
1 2 3 4 5 6
7 8 9
Making a new
4 Turn the jog dial until the number or
name of the desired last track flashes
in the display, and then press the jog
dial.
Making a new group
with 2 groups.
group with
tracks 1 to 3.
Group
Group
This selects the last track of the new
group.
1 2 3 4 5 6 7 8 9
recordings” (page 55) to label a
group.
• Registration of non-consecutive tracks
is not possible (for example, the 1, 3, 2,
4, 3, 5, 6, 6, 8 and then 9).
• Tracks always appear according to their
order on the disc, not their order within
the group (even when group mode is
on).
Notes
track of an existing group or a track that does
not belong to a group.
Jog dial
sure the track comes after the one selected in
track of an existing group or a track that does
not belong to a group.
1 While the recorder is stopped, press
the jog dial, turn the dial until “EDIT”
flashes in the display, and then press
the dial again.
63
To release a group
setting
Moving recorded tracks
You can change the order of the recorded
tracks.
x
GROUP
Example
Move track C (track number 3) from the
third to the second track.
A
B
C
D
Before moving
Jog dial
1 Press GROUP for 2 seconds or more.
A
C
B
D
“
” lights up in the display and the
After moving
group mode turns on.
(page 44) and check the contents of
the group you want to release. Then
press x.
On the recorder
Jog dial
3 Press the jog dial, turn the dial until
“EDIT” flashes in the display, and
then press the dial again.
1 While playing the track you want to
move, press the jog dial, turn the dial
until “EDIT” flashes in the display,
and then press the dial again.
4 Turn the jog dial until “
: Release”
flashes in the display, and press the
jog dial.
“Release?” appears and
“PushENTER” flashes in the display.
The recorder plays the selected track
repeatedly.
5 Press the jog dial.
2 Turn the jog dial until “
: Move”
The group setting of the selected
group is released.
flashes in the display, and then press
the dial.
The selected track number or name of
the group that the selected track
belongs (when the group mode is
turned on) flashes in the display.
If the track has been labeled, press
> to make the track name appear
in the display. Press . to display
the track number again.
64
3 Turn the jog dial until the destination
5 Press x again.
track number flashes in the display.
The selected track moves just before
the destination track.
For the example, since track C will be
moved to track “002”, turn the jog
dial until “002” flashes in the display.
4 Press the jog dial again.
Moving a track to a
different group
The track moves to the selected
destination track.
To cancel moving
Press CANCEL in step 3.
On the recorder
GROUP
On the remote control
DISPLAY
Jog dial
1 While playing the track you want to
move, press GROUP for 2 seconds or
more.
x
Control
1 While playing the track you want to
move press DISPLAY for 2 seconds
or more,
“
” lights up in the display the
group mode turns on.
2 Press the jog dial, turn the dial until
“EDIT” flashes in the display, and
then press the dial again.
2 Turn the control towards . or
N> until “EDIT” flashes in the
display, and then press x.
The recorder plays the selected track
repeatedly.
The recorder plays the selected track
repeatedly.
3 Turn the jog dial until “
: Move”
3 Turn the control towards . or
flashes in the display, and then press
the dial.
N> until “
: Move” flashes in
the display and then press x.
4 Turn the jog dial until the destination
group flashes in the display, and then
press the jog dial.
For the example, “003 t 003”
appears in the display.
4 Turn the control towards . or
N> until the destination track
number flashes in the display.
5 Turn the jog dial until the number of
the destination track within the group
flashes in the display, and then press
the jog dial.
For the example, “003 t 002”
appears in the display.
To cancel moving, press DISPLAY
for 2 seconds or more.
65
On the remote control
Changing the order of a
group on a disc (Group
move)
DISPLAY
On the recorder
GROUP
Control
x
1 While the track you want to move is
playing, press DISPLAY for 2
seconds or more.
2 Turn the control towards . or
N> until “GROUP” flashes in
the display, and then press x.
Jog dial
1 Press GROUP for 2 seconds or more.
3 Turn the control towards . or
N> until “GROUP ON” appears
in the display and then press x.
“
” lights up in the display and the
group mode turns on.
2 While playing a track within a group
whose order you want to change,
press the jog dial, turn the dial until
“EDIT” flashes in the display, and
then press the dial again.
The group mode turns on.
4 Press DISPLAY for 2 seconds or
more.
5 Turn the control towards . or
N> until “EDIT” flashes in the
display, and then press x.
3 Turn the jog dial until “
: Move”
flashes in the display, and then press
the jog dial.
The recorder plays the selected track
repeatedly.
You can now move the selected
group.
6 Turn the control towards . or
N> until “
: Move” flashes in
4 Turn the jog dial to select the
destination point on the disc, and then
press the dial.
the display, and then press x.
7 Turn the control towards . or
N> until the destination group
flashes in the display, and then press
x.
8 Turn the control towards . or
N> until the number of the
destination track within the group
flashes in the display, and then press
x.
66
On the remote control
Adding a track mark
DISPLAY
You can add track marks so that the part
after the new track mark is counted as a
new track.
The track numbers will increase as
follows.
1
2
3
4
5
Control
x
Track marking
1 Press DISPLAY for 2 seconds or
1
2
3
4
more.
Track numbers increase
T MARK
2 Turn the control towards . or
N> until “GROUP” flashes in
the display, and then press x.
3 Turn the control towards . or
N> until “GROUP ON” appears
in the display and then press x.
The group mode turns on.
4 While playing a track within a group
whose order you want to change,
press DISPLAY for 2 seconds or
more.
1 While playing or pausing an MD,
press T MARK on the recorder at the
point you want to mark.
“MARK ON” appears in the display,
and a track mark is added. The track
number will increase by one.
5 Turn the control towards . or
N> until “EDIT” flashes in the
display, and then press x.
z
• The quick search function quickly searches
for specific track or position at which you
wish to add track mark. You can search the
track or position while monitoring either the
track number or name, or elapsed time
6 Turn the control towards . or
N> until “GP : Move” flashes in
the display and then press x.
7 Turn the control towards . or
N> to select a destination point
on the disc, and then press x.
• If you add a track mark in a group, the track
number is added in the group.
To add track marks while
recording (except while
synchoro-recording)
Press T MARK on the recorder at the
point you want to add a track mark.
You can use Auto Time Stamp to add
track marks automatically at specified
intervals (except while digital recording)
67
Notes
• When you erase a track mark between the two
tracks that are registered into different groups,
the second track is re-registered into the group
containing the first track. In addition, if you
combine a track that is registered to a group
with a track that is not registered to a group,
the second track takes the same registration
setting as the first track. However, when the
group function is on, you can only combine
tracks within the selected group.
Erasing a track mark
When you record with analog (line) input,
unnecessary track marks may be recorded
where recording level is low. You can
erase a track mark to combine the tracks
before and after the track mark. The track
numbers will change as follows.
1
2
3
4
• You cannot erase track marks according to the
system limitations. For details, see “System
Erase a track mark
1
2
3
Track numbers decrease
Erasing tracks or
groups
T MARK
x
CANCEL
X/.
Jog dial
1 While playing the track with the track
mark you want to erase, press X to
pause.
To erase a track
2 Find the track mark by pressing .
slightly.
Note that once a recording has
been erased, you cannot retrieve it.
Make sure of the track you are
erasing.
For example, to erase the third track
mark, find the beginning of the third
track. “00:00” appears in the display.
“MARK” appears in the display for 2
seconds.
1 While playing the track you want to
erase, press the jog dial, turn the dial
until “EDIT” flashes in the display,
and then press the dial again.
3 Press T MARK to erase the mark
while “MARK” appears in the
display.
The recorder plays the selected track
repeatedly.
“MARK OFF” appears in the display.
The track mark is erased and the two
tracks are combined.
z
When you erase a track mark, the date, time,
and name assigned to the mark are also erased.
68
2 Turn the jog dial until “
: Erase”
To erase a group
flashes in the display, and then press
the dial.
Note that once a recording has
been erased, you cannot retrieve it.
Be sure to check the contents of
the group before you erase it.
“Erase OK?” appears and
“PushENTER” flashes in the display.
To cancel erasing, press CANCEL.
3 Press the jog dial again.
1 Press GROUP for 2 seconds or more.
The track is erased and the next track
starts to play. All the tracks after the
one erased are automatically
renumbered.
“
” lights up in the display and the
group mode turns on.
2 Follow steps 1 and 2 of the procedure
check the contents of the group you
want to erase. Then press x.
To erase a part of a track
Add track marks at the beginning and the
end of the part you want to erase, then
3 While the recorder is stopped, press
the jog dial, turn the dial until “EDIT”
flashes in the display, and then press
the dial again.
To erase the whole disc
You can quickly erase all the tracks and
data of the MD at the same time.
Note that once a recording has
been erased, you cannot retrieve it.
Be sure to check the contents of
the disc before you erase it.
4 Turn the jog dial until “
: Erase”
flashes in the display, and then press
the jog dial.
The group name and “GP Erase?”
appear and “PushENTER” flashes in
the display. To cancel erasing, press
CANCEL.
1 Play the disc you want to erase to
check the contents, and then press x
to stop.
5 Press the jog dial again.
2 Press the jog dial, turn the dial until
“EDIT” flashes in the display, and
then press the lever again.
The group is erased.
3 Turn the jog dial until “
: Erase”
flashes in the display, and then press
the dial.
“AllErase?” appears and
“PushENTER” flashes in the display.
To cancel erasing, press CANCEL.
4 Press the jog dial again.
“TOC Edit” flashes in the display,
and all the tracks will be erased.
When erasing is complete,
“BLANKDISC” flashes and “00:00”
appears in the display.
69
Other operation
4 Turn the jog dial repeatedly to select
Suppressing the skips
of the sound
the alarm sound.
ON
TIMER 1
TIME:05
(G-PROTECTION)
The G-PROTECTION function was
developed to provide a higher level of
shock resistance than that of existing
players in order to allow the recorder to be
used while jogging.
The following sounds can be selected.
Display
TIMER 1
TIMER 2
TIMER 3
Alarm sound
Classical music 1
Classical music 2
Beeps
Note
The playback sound may skip if:
• the recorder receives stronger continuous
shock.
• a dirty or scratched MiniDisc is played.
5 Press the jog dial.
The alarm sound is set.
6 Turn the jog dial to select the elapsed
Using the alarm
(Melody Timer)
time.
ON
TIMER 1
TIME:05
You can set the alarm timer to go off in 1
to 99 minutes and select three different
alarm sounds.
One rotation of the control changes
the elapsed time setting (TIME :) by 1
minute, within a range of 1 to 99
minutes. To change the time quickly,
keep turning the jog dial.
On the recorder
Jog dial
7 Press the jog dial.
Melody timer is set.
The time remaining until the alarm is
shown in the display while the
recorder is stopped or play-paused.
1 While the recorder is stopped,
playing, or play-paused, press the jog
dial.
To check the time remaining
on the alarm while playing
time and the selected sound appear in the
display.
2 Turn the jog dial until “M-TIMER”
flashes in the display, and press the
dial.
To cancel setting the alarm
Press CANCEL.
3 Turn the jog dial until “ON” flashes
in the display, and then press the dial.
, lights up in the display and the
alarm sound can be selected.
70
6 Turn the control towards . or
On the remote control
N> to select the elapsed time.
DISPLAY
One rotation of the control changes
the elapsed time setting (TIME :) by 1
minute, within a range of 1 to 99
minutes. To change the time quickly,
turn and hold the control towards
. or N>.
Control
x
1 While the recorder is stopped,
7 Press x.
playing, or play-paused, press
The alarm is set.
DISPLAY for 2 seconds or more.
The time remaining until the alarm is
shown in the display while the
recorder is stopped or play-paused.
2 Turn the control towards . or
N> until “M-TIMER” flashes in
the display, and then press x.
To check the time remaining
on the alarm while playing
time and the selected sound appear in the
display.
3 Turn the control towards . or
N> until “ON” flashes in the
display, and then press x.
, lights up in the display and the
alarm sound can be selected.
To cancel setting the alarm
Press DISPLAY for 2 seconds or more.
4 Turn the control towards . or
N> to select the alarm sound.
To cancel Melody Timer
jog dial on the recorder or x on the
remote control.
The following sounds can be selected.
Display
TIMER 1
TIMER 2
TIMER 3
Alarm sound
Classical music 1
Classical music 2
Beeps
To stop the alarm
Press any button. Note that the button’s
original function will not activate at this
time.
z
5 Press x.
previous alarm setting is automatically used.
• After sounding for one minute, the alarm will
automatically stop and the alarm setting will
be canceled. If the alarm sounds during stop
mode, then the power will automatically turn
off 10 seconds after the alarm stops. If the
alarm stops while an MD is playing, the
playback will continue uninterrupted.
The alarm sound is set.
71
Notes
3 Turn the jog dial until “AVL S ON”
flashes in the display, and then press
the dial.
• The settings will be lost when you start
recording.
• The timer will begin counting down (using the
factory setting) from the moment you select
counting down again from the moment you
When you try to turn the volume too
high, “AV LS” appears in the display.
The volume is kept to a moderate
level.
On the remote control
Protecting your hearing
(AVLS)
1 Press DISPLAY for 2 seconds or
more.
The AVLS (Automatic Volume Limiter
System) function keeps down the
maximum volume to protect your ears.
Jog dial
2 Turn the control towards . or
N> until “OPTION” flashes in
the display, and then press x.
3 Turn the control towards . or
N> until “AV LS” flashes in the
display, and then press x.
4 Turn the control towards . or
N> until “AV LS ON” flashes in
the display, and then press x
DISPLAY
To cancel the AVLS
recorder, and then press the jog dial.
remote control, and then press x.
Control
x
On the recorder
1 Press the jog dial, turn the dial until
“OPTION” flashes in the display, and
then press the dial again.
2 Turn the jog dial until “AV LS”
flashes in the display, and then press
the dial.
72
3 Turn the control towards . or
N> until “BEEP” flashes in the
display, and then press x.
Turning off the beep
sound
4 Turn the control towards . or
N> until “BEEP OFF” flashes in
the display, and then press x.
You can turn off the beep sound in the
headphones/earphones.
Jog dial
To turn on the beep sound
recorder, and then press the jog dial.
remote control, and then press x.
DISPLAY
Adjusting the contrast
of the display window
(Contrast adjustment)
Control
You can adjust the contrast of the display
window on the recorder.
x
Jog dial
On the recorder
1 Press the jog dial, turn the dial until
“OPTION” flashes in the display, and
then press the dial again.
2 Turn the jog dial until “BEEP”
flashes in the display and then press
the dial.
1 While the recorder is stopped, press
the jog dial, turn the dial until
“OPTION” flashes in the display, and
then press the dial again.
3 Turn the jog dial until “BEEP OFF”
flashes in the display, and then press
the dial.
2 Turn the jog dial until “CONTRAST”
flashes in the display, and then press
the jog dial.
On the remote control
3 Turn the jog dial to adjust the
contrast, and then press the jog dial.
1 Press DISPLAY for 2 seconds or
more.
Note
You cannot adjust the contrast with the remote
control, nor can you adjust the contrast of the
display on the remote control.
2 Turn the control towards . or
N> until “OPTION” flashes in
the display, and then press x.
73
Locking the controls
(HOLD)
To prevent the buttons from being
accidentally operated when you carry the
recorder, use this function.
HOLD
HOLD
1 Slide HOLD in the direction of the
..
On the recorder, slide HOLD to lock
the controls of the recorder. On the
remote control, slide HOLD to lock
the controls of the remote control.
To unlock the controls
Slide HOLD in the opposite direction of
the arrow.
74
Power sources
When playing
(Unit: approx.hours)(JEITA1))
SP LP2 LP4
Stereo Stereo Stereo
You can use the recorder on house current
or as follows.
In the recorder …
— a nickel metal hydride rechargeable
battery NH-14WM(A) (supplied)
With supplied battery case …
— LR6 (size AA) alkaline dry battery
(not supplied)
Batteries
NH-14WM(A) 24
nickel metal
hydride
27
31
rechargeable
battery2)
It is preferable to use the recorder on
house current when recording for a long
time.
LR6 (SG)
34
40
75
45
84
Sony alkaline
dry battery3)
Battery life1)
When recording2)
NH-14WM(A) 64
nickel metal
hydride
(Unit: approx.hours)(JEITA3))
rechargeable
battery2)
Batteries
SP
LP2
LP4
+ One LR6
(SG)3)
Stereo Stereo Stereo
NH-14WM(A) 8.5
nickel metal
hydride
11
14
1) Measured in accordance with the JEITA
(Japan Electronics and Information
Technology Industries Association) standard.
2) When using a 100% fully charged
rechargeable battery.
rechargeable
battery4)
LR6 (SG)
7.5
12
28
15
37
3) When using a Sony LR6 (SG) “STAMINA”
alkaline dry battery (produced in Japan).
Sony alkaline
dry battery5)
When to replace the batteries
NH-14WM(A) 20
nickel metal
hydride
When the dry battery or rechargeable
battery is weak, flashing r or “LOW
BATT” appears in the display. Replace the
dry battery or charge the rechargeable
battery.
The battery level indicator is approximate.
It may be more or less than the indication
depending on the operating condition.
rechargeable
battery4)
+ One LR6
(SG)5)
1) The battery life may be shorter due to operating
conditions and the temperature of the location.
2) When you record, use a fully charged
rechargeable battery. Recording time may
differ according to the alkaline batteries.
3) Measured in accordance with the JEITA (Japan
Electronics and Information Technology
Industries Association) standard.
Note
Stop the recorder before replacing battery.
4) When using a 100% fully charged rechargeable
battery.
5) When using a Sony LR6 (SG) “STAMINA”
alkaline dry battery (produced in Japan).
75
Additional information
On the headphones/earphones
Road safety
Precautions
Do not use headphones/earphones while
driving, cycling, or operating any motorized
vehicle. It may create a traffic hazard and is
illegal in many areas. It can also be potentially
dangerous to play your recorder at high volume
while walking, especially at pedestrian
crossings. You should exercise extreme caution
or discontinue use in potentially hazardous
situations.
On safety
Do not put any foreign objects in the DC IN 3V
jack.
On power sources
• Use house current, nickel metal hydride
rechargeable battery, LR6 (size AA) battery,
or car battery.
• For use in your house: For the supplied battery
charging stand, use the AC power adaptor
supplied with this recorder. Do not use any other
AC power adaptor since it may cause the recorder
to malfunction.
Preventing hearing damage
Avoid using headphones/earphones at high
volume. Hearing experts advise against
continuous, loud and extended play. If you
experience a ringing in your ears, reduce the
volume or discontinue use.
Caring for others
Polarity of the
plug
Keep the volume at a moderate level. This will
allow you to hear outside sounds and to be
considerate of the people around you.
• The recorder is not disconnected from the AC
power source (mains) as long as it is
connected to the wall outlet, even if the
recorder itself has been turned off.
• If you are not going to use this recorder for a
long time, be sure to disconnect the power
supply (AC power adaptor, dry battery,
rechargeable battery, or car battery cord). To
remove the AC power adaptor from the wall
outlet, grasp the adaptor plug itself; never pull
the cord.
On the MiniDisc cartridge
• When carrying or storing the MiniDisc, keep
it in its case.
• Do not break open the shutter.
• Do not place the cartridge where it will be
subject to light, extreme temperatures,
moisture or dust.
• Attach the supplied MD label only in the
space designated for it on the disc. Do not
stick it on any other disc surface.
On heat build-up
Heat may build up in the recorder if it is used
for an extended period of time. This, however,
is not a malfunction.
On the dry battery case
The supplied dry battery case is designated for
this recorder only.
On cleaning
On installation
• Clean the recorder casing with a soft cloth
slightly moistened with water or a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent such
as alcohol or benzene as it may mar the finish
of the casing.
• Never use the recorder where it will be
subjected to extremes of light, temperature,
moisture or vibration.
• Never wrap the recorder in anything when it is
being used with the AC power adaptor. Heat
build-up in the recorder may cause
malfunction or damage.
• Wipe the disc cartridge with a dry cloth to
remove dirt.
• Dust on the lens may prevent the unit from
operating properly. Be sure to close the disc
compartment lid after inserting or ejecting an
MD.
76
• To obtain the best sound quality, use a dry
cloth to wipe the plugs of the headphones/
earphones or the remote control. Dirty plugs
may cause sound distortion or intermittent
breaks in the sound.
Note on digital recording
This recorder uses the Serial Copy
Management System, which allows only first-
generation digital copies to be made from
premastered software. You can only make
copies from a home-recorded MD by using the
analog (line out) connections.
Notes on batteries
Incorrect battery usage may lead to leakage of
battery fluid or bursting battery. To prevent
such accidents, observe the following
precautions:
Premastered software such as CDs or
MDs.
• Install the + and – poles of the batteries
correctly.
• Do not try to recharge dry battery.
• When the recorder is not to be used for a long
time, be sure to remove the batteries.
• If a battery leak should develop, carefully and
thoroughly wipe away battery fluid from the
battery compartment before inserting new
ones.
Digital recording
Home-
recorded digital
MD recording
No
Recordable
MD
Note on mechanical noise
The recorder gives off mechanical noise while
operating, which is caused by the power-saving
system of the recorder and it is not a problem.
To protect a recorded MD
Microphone, record player, tuner, etc. (with
analog output jacks).
To record-protect an MD, slide open the tab at
the side of the MD. In this position, the MD
cannot be recorded. To record again, slide the
tab back so the tab is visible.
Tab
Analog recording
Home-recorded MD
Digital recording
Recorded material is
protected.
Back of the MD
Recorded material is
not protected.
No
digital
recording
Recordable
MD
Recordable
MD
77
Note on maintenance
Clean the terminals periodically with a cotton
swab or a soft cloth as illustrated.
Terminals
If you have any questions or problems
concerning your recorder, please consult your
nearest Sony dealer. (If a trouble occurred when
the disc was in the recorder, we recommend that
the disc be left in the recorder when you consult
your Sony dealer so that the cause of trouble
may be better understood.)
78
Troubleshooting
Should any problem persist after you have made these checks, consult your nearest Sony
dealer.
Symptom
Cause/Solution
The recorder does • Audio sources may not be securely connected.
not work or works
poorly.
, Disconnect the audio sources once and connect them again
• The HOLD function is turned on (“HOLD” appears in the display
when you press an operation button on the recorder).
, On the recorder, disable HOLD by sliding the HOLD switch to
• The lid is not firmly closed.
, Close the lid until it clicks. Then press OPEN to open the lid.
• Moisture has condensed inside the recorder.
, Take the MD out and leave the recorder in a warm place for
several hours until the moisture evaporates.
• The rechargeable battery or dry battery is weak (“LOW BATT”
flashes or nothing appears).
, Charge the rechargeable battery or replace the dry battery with
adaptor to the recorder.
• The rechargeable battery or dry battery have been inserted
incorrectly.
• You pressed a button while the disc indication was rotating quickly.
, Wait until the indication rotates slowly.
• When recording digitally from a portable CD player, you did not
use AC power or did not disable the anti-skip function such as ESP
• The analog recording was made using a connecting cord with an
attenuator.
• The AC power adaptor was unplugged during recording or a power
outage occurred.
• While operating, the recorder received a mechanical shock, too
much static, abnormal power voltage caused by lightning, etc.
, Restart the operation as follows.
1 Disconnect all the power sources.
2 Leave the recorder for about 30 seconds.
3 Connect the power source.
• The disc is damaged or does not contain proper recording or editing
data.
, Reinsert the disc. Rerecord the disc. If the error message still
appears, replace it with another disc.
79
Symptom
Cause/Solution
The recorder does • The disc is record-protected (“PROTECTED” appears).
not work or works
poorly.
• Recording level is too small to record (when recording manually).
, Pause the recorder and adjust the recording level.
• A Premastered MD is inserted (“P/B ONLY” appears) when
recording.
, Insert a recordable MD
• The recorder is operated when it is on a battery charging stand.
, Remove the recorder from the battery charging stand.
• You tried to turn the group mode on while setting the program.
, Turn the group mode on before setting the program.
The recorder
overwrites
• The record starting-position setting (“REC-Posi”) is set to “From
Here”.
existing materials
when record.
, Set “REC-Posi” setting to “From End”.
“NO SIGNAL”
appears in the
display when
recording from a
portable CD
player.
• There is no digital signal from the portable CD player.
, When recording digitally from a portable CD player, use the AC
power adaptor and disable the anti-skip function (such as ESP)
There is no
recording on the
MD after a
recording
• The AC power adaptor was unplugged or a power outage occurred
during recording.
operation.
The lid does not
open.
• The power sources have been disconnected during recording or
editing, or the battery have been exhausted.
, Set the power sources again, or replace the exhausted battery
with new ones.
• The lid is not firmly closed.
, Close the lid until it clicks. Then press OPEN to open the lid.
No sound comes • The headphones/earphones plug is not firmly connected.
through the
headphones/
earphones.
, Plug in the plug of the headphones/earphones firmly to the
remote control. Plug in the plug of the remote control firmly to
i/LINE OUT.
• Volume is too low.
, Adjust the volume by pressing VOL +/–.
• The plug is dirty.
, Clean the plug.
• The “AUDIO OUT” parameter for the i/LINE OUT jack is set to
“LINE OUT”.
, Set to “HeadPhone”.
80
Symptom
Cause/Solution
Volume cannot be • AVLS is on.
turned up.
An MD is not
• Playback mode is changed.
played normally.
, Use the jog dial on the recorder or press RPT/ENT on the
remote control to change back to the normal play.
An MD is not
played from the
first track.
• Disc playing stopped before it came to the last track.
, Press N for 2 seconds or more to start playing, or press the
control towards . repeatedly on the remote.
• The group mode is turned on.
, Turn the group mode off and play from the first track (press N
for 2 seconds or more to start playing, or press the control
towards . repeatedly on the remote).
• The disc information has been stored to the Personal Disc Memory.
, Erase the disc information from the Personal Disc Memory.
Playback sound
skips.
• The recorder is placed where it receives continuous vibration.
, Put the recorder on a stable place.
• A very short track may cause sound to skip.
Sound has a lot of • Strong magnetism from a television or such device is interfering
static.
with operation.
, Move the recorder away from the source of strong magnetism.
Cannot find the
track marks.
• You pressed X after pressing . or >.
, Press X before turning the jog dial or pressing . or >.
The rechargeable • The rechargeable battery has been inserted incorrectly or the AC
battery does not
start charging.
The rechargeable
battery cannot be
fully charged.
power adaptor has been connected incorrectly.
, Insert the battery correctly or connect the AC power adaptor
correctly.
• The terminals of the battery charging stand is dirty.
, Clean the terminals with a dry cloth.
The clock loses
time or the display
flashes.
The recording
date was not
stamped onto the
disc.
• The built-in battery for the clock is weak.
, Connect the AC power adaptor to DC IN 3V on the recorder and
the wall outlet to charge the built-in battery. After charging, set
up to about 2 minutes per month under normal condition.
• The clock is not set.
CD text
• The cable connecting the devices is not an optical cable.
, Use an optical cable to connect the devices.
• The connected portable CD player does not supports CD-TEXT.
, Connect a portable CD player (D-E999, etc.) that supports CD-
information
cannot be
recorded.
• The inserted CD does not support CD-TEXT.
, Insert a CD that supports CD-TEXT.
81
Symptom
Cause/Solution
VOL +/– or
Digital Sound
Preset does not
function
• The “AUDIO OUT” parameter is set to “LINE OUT”.
The disc cannot
edit on other
component.
• The component does not support LP2 stereo or LP4 stereo.
, Edit on other component that support LP2 stereo or LP4 stereo.
Momentary noise • Due to the special digital audio compression technology used in
is heard.
LP4 stereo mode, momentary noise may occur on very rare
occasions with certain sound sources.
, Record in normal stereo or LP2 stereo mode.
The group
• While using a disc that has no group information, an attempt was
made to turn the group mode on (“No Group” appears).
, Use a disc with a group information.
• When selecting program play, an attempt was made to turn the
group mode on.
function (group
mode/group skip
mode) does not
operate.
, Turn the group mode on, before selecting program play.
The display
window is not
normal.
• The recorder was disconnected from the power source.
, Let the recorder sit for a while, or disconnect the power source,
reconnect it, and then press any of the operation buttons.
82
System limitations
The recording system in your MiniDisc recorder is radically different from those used in
cassette and DAT decks and is characterized by the limitations described below. Note,
however, that these limitations are due to the inherent nature of the MD recording system
itself and not to mechanical causes.
Symptom
Cause
“TR FULL”
When 254 tracks have been recorded on the disc, “TR FULL”
appears even before appears regardless of the total recorded time. More than 254 tracks
the disc has reached cannot be recorded on the disc. To continue recording, erase
the maximum
unnecessary tracks.
recording time (60,
74, or 80 minutes)
and the recording
cannot be done.
“TR FULL”
Repeated recording and erasing may cause fragmentation and
appears even before scattering of data. Although those scattered data can be read, each
the disc has reached fragment is counted as a track. In this case, the number of tracks
the maximum track may reach 254 and further recording is not possible. To continue
number or
recording time.
recording, erase unnecessary tracks.
Track marks cannot When the data of a track is fragmented, the track mark of a
be erased.
fragment under 12 seconds long (recorded in SP stereo), 24 seconds
long (recorded in LP2 stereo mode or monaural mode), or 48
seconds long (recorded in LP4 stereo mode) cannot be erased. You
cannot combine tracks recorded in different recording modes, e.g., a
track recorded in stereo and a track recorded in monaural; nor can
you combine a track recorded with digital connection and a track
recorded with analog connection.
Tracks of under 12 seconds, 24 seconds, or 48 seconds in length are
not counted and so erasing them may not lead to an increase in the
recording time.
The remaining
recording time does
not increase even
after erasing
numerous short
tracks.
The total recorded Normally, recording is done in minimum units of approximately 2
time and the seconds (in SP stereo), 4 seconds (in LP2 stereo mode or
remaining time on monaural), or 8 seconds (in LP4 stereo mode). When recording is
the disc may not stopped, the last unit of recording always uses this unit of 2
total the maximum seconds, 4 seconds, or 8 seconds even if the actual recording is
recording time (60, shorter. Likewise, when recording is restarted after the stop, the
74, or 80 minutes). recorder will automatically insert a blank space amounting to 2
seconds, 4 seconds, or 8 seconds before the next recording. (This is
to prevent accidental erasing of a previous track whenever a new
recording is started). Therefore, the actual recording time will
decrease whenever a recording is stopped by a maximum of 6
seconds, 12 seconds, or 24 seconds.
The edited tracks
The fragmentation of data may cause sound dropout while
may exhibit sound searching because the tracks are played in higher speed than normal
dropout during
search operations.
playback.
83
Messages
If the following error messages flash in the display window, check the chart below.
Error message Meaning/Remedy
BANK FULL
• The name bank is almost full and cannot store the phrase you tried
to enter.
, Delete some phrases from the name bank, and then reenter the
new phrase.
BLANKDISC
BUSY
• An MD with no recording on it is inserted.
• You tried to operate the recorder while it was accessing the
recorded data.
, Wait until the message goes out (in rare cases, it may take a
few minutes).
Data Save
• The MD player is recording information (sounds) from the
memory to the disc.
, Wait until this process is completed. Do not expose the player
to any physical shock, nor disrupt power supply.
DISC ERR
• The disc is damaged or does not contain proper recording or
editing data.
, Reinsert the disc. If this fails, rerecord.
DISC FULL
• The remaining recording time on the disc is 12 seconds (SP
stereo), 24 seconds (LP2 stereo or monaural), 36 seconds (LP4
stereo), or less.
, Replace the disc.
EMPTY
Hi DC in
• You tried to erase data in the name bank but no data have been
recorded.
• Voltage of the power supply is too high (The supplied AC power
adaptor or the recommended car battery cord is not used).
, Use the supplied AC power adaptor or the recommended car
battery cord.
HOLD
• The recorder is locked.
, Slide HOLD against the arrow to unlock the recorder
LINE OUT
• You pressed VOL +/– while the “AUDIO OUT” parameter was set
to “LINE OUT.”
, Use the jog dial to set the “AUDIO OUT” parameter to
LOW BATT
• Batteries are weak.
, Charge the rechargeable battery or replace the dry battery
84
Error message Meaning/Remedy
MEM OVER
• You tried to record with the recorder placed where it receives
continuous vibration.
, Put the recorder on a stable place, and start recording again.
MENU
• You pressed a key on the remote control while selecting a menu on
the recorder. You pressed a key on the recorder while selecting a
menu on the remote control.
NAME FULL
• You tried to enter more than 200 letters to label a single track or
disc.
• You tried to enter a total of more than 1700 letters for track or disc
names.
set the “LP Stamp” setting to “Stamp OFF” so that “LP:” is not
added at the beginning of the track name (page 29).
NO BATT
NO COPY
• The rechargeable battery is not inserted.
, Insert a rechargeable battery.
• You tried to make a copy from a disc that is protected by the Serial
Copy Management System. You cannot make copies from a
digitally connected source which was itself recorded using digital
connection.
NO DISC
• You tried to play or record with no disc in the recorder.
, Insert an MD.
No Entry!
NO SIGNAL
NO TEXT
P/B ONLY
• You tried to erase a setting in the Personal Disc Memory on a disc
that contains no settings in the Personal Disc Memory.
• The recorder could not detect digital input signals.
, Make sure that the source is connected firmly (page 22).
• You tried to use the CD text copying function to copy a track or
disc name from a CD that has no text data (page 40).
• You tried to record or edit on a pre mastered MD (P/B stands for
“playback”).
, Insert a recordable MD.
PROTECTED
• You tried to record or edit on a MD with the tab in the record-
protect position.
, Slide the tab back (page 77).
85
Error message Meaning/Remedy
SORRY
• You tried to erase the track mark at the beginning of the first track.
• You tried to erase a track mark to combine tracks the recorder
cannot combine (a track recorded in stereo and in mono, for
example).
• You tried to overwrite a track marks.
• You tried to set Digital Sound Preset while the “AUDIO OUT”
parameter was set to “LINE OUT”.
, Use the jog dial to set the “AUDIO OUT” parameter to
• You tried to press X or T MARK during synchro-recording.
• You tried to turn on the group function while programming.
, Turn the group function on before programming.
TEMP OVER
TOC Edit
• Heat has built up in the recorder.
, Let the recorder cool down.
• The MD player is recording information (track start and end
position) from the memory to the disk.
, Wait until this process is completed. Do not expose the player
to physical shock, nor disrupt power supply.
TR FULL
• Track number 254 has been reached.
TrPROTECT
• You tried to record or edit on a track that is protected from erasing.
, Record or edit on other tracks.
86
Power requirements
Sony AC Power Adaptor connected at the DC
IN 3V jack:
Specifications
120 V AC, 60 Hz (U.S.A., Canadian and
Taiwan model)
230 V AC, 50/60 Hz (Europe continental
model)
Audio playing system
MiniDisc digital audio system
Laser diode properties
Material: GaAlAs
240 V AC, 50 Hz (Australian model)
220 V AC, 50 Hz (Chinese model)
230 - 240 V AC, 50 Hz (U.K. and Hong
Kong model)
Wavelength: λ = 790 nm
Emission duration: continuous
Laser output: less than 44.6 µW
(This output is the value measured at a distance
of 200 mm from the lens surface on the optical
pick-up block with 7 mm aperture.)
Recording and playback time
When using MDW-80:
220 V AC, 50 Hz (Argentina model)
110/220 V AC, 60 Hz (Korean model)
100 - 240 V AC, 50/60 Hz (Other models)
Nickel metal hydride rechargeable battery NH-
14WM(A) 1.2V 1350 mAh (MIN) Ni-MH
LR6 (size AA) alkaline battery
Battery operation time
Dimensions3)
Maximum 160 min. in monaural
Maximum 320 min. in stereo
Revolutions
350 rpm to 2,800 rpm (CLV)
Error correction
ACIRC (Advanced Cross Interleave Reed
Solomon Code)
Sampling frequency
44.1 kHz
Approx. 78.9 × 72.0 × 17.1 mm (w/h/d)
(31/8 × 27/8 × 11/16 in.)
Mass
Approx. 110 g (3.9 oz) the recorder only
Sampling rate converter
Input: 32 kHz/44.1 kHz/48 kHz
Coding
ATRAC (Adaptive TRansform Acoustic
Coding)
1)The LINE IN (OPT) jack is used to connect
either a digital (optical) cable or a line
(analog) cable.
2)The i/LINE OUT jack connects either
headphones/earphones or a line cable.
3)Measured in accordance with JEITA.
ATRAC3 — LP2
ATRAC3 — LP4
Modulation system
Supplied accessories
AC power adaptor (1)
Headphones/earphones with a remote control
(1)
Battery charging stand (Assembly needed) (1)
Rechargeable battery (1)
Dry battery case (1)
Rechargeable battery carrying case (1)
Carrying pouch/carrying case with a belt clip
(1)
AC plug adaptor (Except Europe, China and
HongKong model) (1)
EFM (Eight to Fourteen Modulation)
Number of channels
2 stereo channels
1 monaural channel
Frequency response
20 to 20,000 Hz 3 dB
Wow and Flutter
Below measurable limit
Inputs
Microphone: stereo mini-jack, minimum input
level 0.25 mV
level 49 mV
Optical cable (1)
Outputs
US and foreign patents licensed from Dolby
Laboratories.
remote control jack) 194 mV (10 kohm)
Maximum output (DC)2)
Headphones: 5 mW + 5 mW (16 ohm)
Design and specifications are subject to change
without notice.
87
Optional accessories
Optical Cable
POC-151HG, POC-152HG, POC-MZ1,
POC-MZ2, POC-15B, POC-15AB, POC-
DA12SP
What is an MD?
How MiniDisc works
MiniDisc (MD) comes in two types:
premastered (prerecorded) and recordable
(blank). Premastered MDs, recorded at
music studios, can be played back almost
endlessly. However, they can’t be recorded
on or over like cassette tapes. To record, you
must use a “recordable MD”.
Line Cable RK-G129, RK-G136
Stereo Microphones ECM-717, ECM-MS907,
ECM-MS957
Stereo Headphones/earphones* MDR-EX70LP,
MDR-Q33LP, MDR-A110LP
CD text connecting cable RK-TXT1
Active Speakers SRS-Z500
Recordable MDs MDW-series
Premastered MDs
You cannot use the following accessories with
this recorder.
MD label printer MZP-1
IC memory
Repeat learning
MD controller RPT-M1
Premastered MDs are recorded and played
like regular CDs. A laser beam focuses on
the pits in the surface of the MD and reflects
the information back to the lens in the
recorder. The recorder then decodes the
signals and plays them back as music.
Your dealer may not handle some of the above
listed accessories. Please ask the dealer for
detailed information about the accessories in
your country.
∗ Whether you should plug the headphones/
earphones directly to i/LINE OUT on the
main unit or to a remote control, use only
headphones/earphones with stereo mini
plugs.
Recordable MDs
Recordable MDs, which use magneto-
optical (MO) technology, can be recorded
again and again. The laser inside the
recorder applies heat to the MD,
stereo mini plugs
demagnetizing the magnetic layer of the
MD. The recorder then applies a magnetic
field to the layer. This magnetic field
corresponds exactly to the audio signals
generated by the connected source. (The
north and south polarities equate to digital
“1” and “0”.) The demagnetized MD adopts
the polarity of the magnetic field, resulting
in a recorded MD.
micro plug
88
How the MiniDisc got so small
The 2.5-inch MiniDisc, encased in a plastic
cartridge that looks like a 3.5-inch diskette
digital audio compression technology called
ATRAC (Adaptive TRansform Acoustic
Coding). To store more sound in less space,
ATRAC extracts and encodes only those
frequency components actually audible to
the human ear.
Quick Random Access
Like CDs, MDs offer instantaneous random
access to the beginning of any music track.
Premastered MDs are recorded with location
addresses corresponding to each music
selection.
Recordable MDs are manufactured with a
“User TOC Area” to contain the order of the
music. The TOC (Table of Contents) system
is similar to the “directory management
system” of floppy disks. In other words,
starting and ending addresses for all music
tracks recorded on the disc are stored in this
area. This lets you randomly access the
beginning of any track as soon as you enter
the track number (AMS), as well as label the
location with a track name as you would a
file on a diskette.
A
B
A — User TOC area
Contains the order and start/end points of
the music.
B — Music Data
89
Sony Corporation Printed in Japan
|