Seagate ST3160022ACE User Manual

Jumper settings for this drive are shown below  
Drive is master  
or single drive  
Drive is slave  
Use cable select  
U Series 9 ce Installation Guide  
ST3160022ACE, ST3120025ACE and ST380012ACE  
ATA Interface Disc Drives  
Drive is master with non-  
ATA-compatible slave  
Master/slave jumpers (see table for key to jumper settings)  
Publication Number: 100271708, Rev. B, December 2003  
The easiest way to install your drive  
DiscWizardTM, available exclusively from Seagate, provides you with cus-  
tomized installation instructions for your hard drive. You can download Dis-  
or run the program directly from your web browser. In either case, you  
should run DiscWizard before you install your drive.  
2. Mount the drive and attach cables  
a. Slide the drive into a 3.5-inch drive bay. You can mount the drive in any  
orientation, but we recommend mounting with the circuit board down.  
Note. To mount the drive in a 5.25-inch drive bay, you must purchase  
mounting brackets, available from your computer dealer.  
b. Secure the drive using four 6-32 UNC mounting screws in either the  
side-mounting or bottom-mounting holes. Insert the screws no more  
than 0.20 inches (5.08 mm) into the bottom-mounting holes and no  
more than 0.14 inches (3.55 mm) into the side-mounting holes.  
If you cannot run DiscWizard, follow the instructions on this installation  
sheet to install and configure your drive.  
What you need  
Caution. Do not overtighten the  
• A Phillips screwdriver and four 6-32 UNC drive mounting screws  
• Forced-air ventilation to provide adequate drive cooling  
screws or use metric  
screws. This may dam-  
age the drive.  
Existing  
hard drive  
BLACK  
connector  
• An ATA interface cable. For optimum drive performance and data integ-  
rity, we recommend using an 80-conductor Ultra ATA/100 cable (which  
can be identified by its blue, gray, and black connectors).  
c. Make sure the blue connector  
on your Ultra ATA/100 cable is  
plugged into the primary IDE  
port on your computer’s moth-  
erboard or host adapter. See  
your computer manual to deter-  
mine the location of the primary  
IDE connector.  
Computer  
Handling precautions/Electrostatic discharge protection  
Motherboard  
• Disc drives are fragile. Do not drop or jar the drive. Handle the drive only  
by the edges or frame. Keep the drive in the protective SeaShellTM con-  
tainer until you are ready to install it to minimize handling damage.  
• Drive electronics are extremely sensitive to static electricity. While  
installing the drive, wear a wrist strap and cable connected to ground.  
• Turn off the power to the host system during installation.  
• Do not disassemble the drive; doing so voids the warranty. Return the  
entire drive for depot service if any part is defective.  
Primary  
IDE port  
New  
Seagate  
drive  
d. Make sure the black connector  
on the cable is plugged into  
your existing hard drive.  
GRAY  
connector  
BLUE  
connector  
e. Plug the gray connector into  
your new Seagate hard drive.  
• Do not apply pressure or attach labels to the circuit board or to the top of  
the drive.  
Caution. When plugging in the  
interface cable, make  
Breather filter hole precaution  
sure that pin 1 on the cable (indicated by a stripe along the  
edge) is attached to pin 1 on the drives and on the mother-  
board’s IDE connector.  
f. Attach the 4-pin power connector to the drive. See figure below.  
Key on cable connector  
fits into slot on drive connector  
Breather Hole  
Do not cover  
or seal.  
Pin 1  
Power connetor  
Stripe on cable  
Caution. Do not cover, seal, or insert any object into this hole.  
This hole has two purposes:  
Note. If your computer does not have an unused power cable for your new  
hard drive, you can purchase a Y-shaped power splitting cable from  
your computer dealer which effectively converts one power connec-  
tor into two.  
To allow condensation inside the hard disc to escape  
To allow air pressure inside the hard disc to equalize with ambient pres-  
sure  
Note. If this hole is covered, sealed, or penetrated by any object, the drive  
reliability may be compromised and could lead to permanent  
damage—doing so voids the warranty.  
3. Start up your computer  
Close your computer case and restart your computer. your computer may  
automatically detect your new drive. If your computer does not automati-  
cally detect your new drive, follow the steps below.  
Installation instructions  
a. Restart your computer.  
1. Set the jumpers  
b. While the computer restarts, run the System Setup program (some-  
times called BIOS or CMOS setup). This is usually done by pressing a  
special key, such as DELETE, ESC, or F1 during the startup process.  
c. Within the System Setup program, instruct the system to auto detect  
your new drive.  
Note. The instructions below assume that you are installing your new  
Seagate drive in a system that already has a working hard drive. To  
install the drive in a system that has no working hard drive, see the  
section titled, “What to do if you don’t have a working hard drive”  
located on back of this sheet.  
d. Enable LBA and UDMA modes if the Setup program gives you this  
option.  
a. Make sure that your existing drive is set up as a “master.” See the drive  
label or manufacturer’s web site for jumper settings.  
e. Save the settings and exit the Setup program. When your computer  
restarts, it should recognize your new drive. If your system still doesn’t  
recognize your new drive, see the troubleshooting section on the back  
b. Your new drive is shipped with a jumper in the “cable select” position.  
Set the drive as a “slave” by removing this jumper from the jumper  
pins. Save the jumper in case you ever need to reconfigure the drive.  

Sprint Nextel Cell Phone PG86100 User Manual
Sony Xperia arco S LT26w User Manual
Siemens GPS1000 2XV9450 1AR82 User Manual
Seagate Cheetah ST3450857FC User Manual
Seagate CHEETAH 15K7 FC ST3600957FC User Manual
Samsung SW 248F User Manual
Roberts Radio CR950 User Manual
Pioneer DEH P3150 B User Manual
Norcent Technologies SDDuo 1GB UPC TBD User Manual
Nokia CAR KIT CK 100 User Manual