Product Manual
Lyrion Series IDE
ST760211DE
ST730212DE
100462437
Rev. B
May 2007
Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Drive care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Time to ready. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Voltage tolerance and Maximum current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Power-management modes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Corrosive environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Handling and static discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Drive installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Mounting considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Interface description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Connector interface signals and connector pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Register default values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.0
Seagate Technology support services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Lyrion Series IDE Product Manual, Rev. B
i
ii
Lyrion Series IDE Product Manual, Rev. B
List of Figures
Figure 8.
Lyrion Series (IDE interface) disc drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Typical 3.3V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Location where tri-axial accelerometer will be placed on Lyrion Series drives. . . . . . . . . . . . 11
Drive axis definition for Lyrion Series drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Lyrion Series breather hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Lyrion Series proper handling example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Lyrion Series mechanical dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . 21
Lyrion Series Area for Protective Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Lyrion Series IDE Product Manual, Rev. B
iii
iv
Lyrion Series IDE Product Manual, Rev. B
1.0
Introduction
This manual describes the functional, mechanical and interface specifications for the following Seagate® Lyrion
Series® IDE drives:
• ST760211DE-60GB, ST730212DE-30GB disc drives with an IDE interface.
These drives provide the following key features.
• 3,600-RPM spindle speed and a 2-Mbyte buffer combined for superior read/write performance.
• Quiet operation. Fluid Dynamic Bearing (FDB) motor.
• Perpendicular recording heads and EPRML technology, which provide the drives with increased areal density.
• State-of-the-art cache and on-the-fly error-correction algorithms.
• 1500 G nonoperating shock, and 500 G operating shock.
• SeaTools™ diagnostic software performs a drive self-test that eliminates unnecessary drive returns.
Figure 1.
Lyrion Series (IDE interface) disc drive
Lyrion Series IDE Product Manual, Rev. B
1
1.1
Disclaimer
Seagate Technology LLC makes no warranties whatsoever, including any warranty of merchantability, non-
infringement, fitness for any particular purpose, or any warranty otherwise arising out of any proposal,
specification or sample. Seagate may not be held liable for any direct, indirect, incidental, special, exemplary,
or consequential damages (including, but not limited to, loss of use, data, or profits; procurement of substitute
goods or services; or business interruptions) however caused and on any theory of liability, whether in contract,
strict liability, or tort (including negligence or otherwise) arising in any way from the use of this kit, even if
advised of the possibility of such damage.
1.2
Drive care
Do not use the Lyrion Series disc drives outside of the ranges of environmental conditions found in Section 2.8,
"Environmental specifications." Doing so may void the warranty of the Lyrion Series disc drive.
2
Lyrion Series IDE Product Manual, Rev. B
2.0
Drive specifications
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate
ST760211DE and ST730212DE model drives.
2.1
Overview
The specifications listed in this table are for quick reference. For details on specification measurement or
definition, see the appropriate section of this manual.
Table 1:
Specifications
Drive specification
ST760211DE
ST730212DE
Formatted Gbytes
60
30
Guaranteed sectors
117,210,240
512
58,605,120
Bytes per sector (logical)
Cache (Mbytes)
2
Recording density, BPI (bits/inch average)
Track density. TPI (tracks/inch average)
Areal density (Gbits/inch2 average)
Spindle speed (RPM)
1,025,000
165,000
169
3,600
Internal data transfer rate OD (Mbits/sec max)
Sustained data transfer rate OD (Mbytes/sec)
I/O data-transfer rate (Mbytes/sec max)
ATA data-transfer modes supported
350
24.5
66.7 (UDMA 4)
PIO modes 0–4;
Multiword DMA modes 0-2;
Ultra DMA modes 0–4
Height
5.0 + 0.15 mm(0.1968 + 0.006 inches)
Width
54.0 +/-0.3 mm (2.1260 +/-0.0118 inches)
Length
71.0 +/-0.3 mm (2.7953 +/-0.0118 inches)
Weight
48.0 gm - 0.1058 lb. (typ)
Average latency (msec)
8.3
Power-on to ready (sec typical)
Standby to ready (sec typical)
Startup power (peak at 3.3v) (maximum RMS in 10ms window)
Read/write power (typical 3.3V)
Performance idle power (typical 3.3V)
Low power idle power (typical 3.3V)
Standby/Sleep power (typical 3.3V)
Voltage tolerance (including noise)
Ambient temperature
1.8
1.8
1.15 W
1.0/0.9 W
0.5 W
0.3 W
0.08 W
3.3V ± 5%
0° to 60°C (operating)
–40° to 70°C (nonoperating)
Lyrion Series IDE Product Manual, Rev. B
3
Table 1:
Specifications
Drive specification
ST760211DE
ST730212DE
Temperature gradient (°C per hour max)
20°C (operating)
30°C (nonoperating)
Relative humidity (noncondensing)
5% to 90% (operating)
5% to 95% (nonoperating)
Relative humidity gradient
30% per hour max
Wet bulb temperature (°C max)
33°C (operating)
40°C (nonoperating)
Altitude, operating
–60.98 m to 3,048 m (–200 ft to 10,000+ ft)
Altitude, nonoperating (below mean sea level, max)
Shock, operating (Gs max at 2 msec)
Shock, nonoperating (Gs max at 1 msec)
–60.98 m to 12,192 m (–200 ft to 40,000+ ft)
500
1500
Vibration, operating
(max displacement may apply below 10 hz)
1.0 Gs (0 to peak, 10–500 Hz) @ 2 oct/min sweep rate
5.0 Gs (0 to peak, 10–500 Hz) @ 0.5 oct/min sweep rate
Vibration, nonoperating
(max displacement may apply below 22 hz)
Idle sound power (bels) (typical)
Operational sound power (bels) (typical)
Nonrecoverable read errors
1.6
2.2
14
1 per 10 bits read
Load/Unload (LUL) cycles
20,000 power loss
2.2
Formatted capacity
Model
Formatted
capacity
Guaranteed
sectors
Bytes per
sector (logical)
ST760211DE
ST730212DE
60 Gbytes
30 Gbytes
117,210,240
58,605,120
512
512
LBA mode addressing
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,
where n is the number of guaranteed sectors as defined above.
2.3
Default logical geometry
Model
Cylinders
Heads
16
Sectors
63
ST760211DE
ST730212DE
116,280
58,149
16
63
4
Lyrion Series IDE Product Manual, Rev. B
2.4
Recording and interface technology
Technology
Interface
Specification
IDE (Parallel ATA)
Recording method
Perpendicular Magnetic Recording
Recording density BPI (bits/inch average)
Track density TPI (tracks/inch average)
1,025,000
165,000
169
2
Areal density (Gbits/inch average)
Spindle speed (RPM) (± 0.2%)
3,600
Internal data-transfer rate OD (Mbits/sec max)
Sustained data transfer rate OD (Mbytes/sec max)
I/O data-transfer rate (Mbytes/sec max)
Cache buffer (Mbytes)
350
24.5
66.7 (UDMA 4)
2
2.5
Physical characteristics
Height
Width
(mm)
(inches)
5.0 + 0.15
0.1968 + 0.006
(mm)
(inches)
54.0 +/-0.3
2.1260 +/-0.0118
Length
(mm)
(inches)
71.0 +/-0.3
2.7953 +/-0.0118
Typical weight
(grams)
(pounds)
48.0 (typ)
0.1058 lb. (typ))
Interface Connector
40-way ZIF
2.6
Time to ready
Time to ready
Typical
1.8
Power-On to Ready (sec)
Standby to Ready (sec)
1.8
Lyrion Series IDE Product Manual, Rev. B
5
2.7
Power specifications
The drive receives DC power (+3.3V) through the ZIF connector (IDE interface).
2.7.1 Power consumption
Power requirements for the drives are listed in the table on page 7. Typical power measurements are based on
an average of drives tested, under nominal conditions, using +3.3V input voltage at 25°C ambient temperature.
• Startup mode
Startup power is measured from the time of power-on to the time that the drive spindle reaches operating speed.
• Seek mode
During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and does
not execute a read or write operation. Servo electronics are active. Seek power is measured based on three
random seek operations every 100 msecs.
• Read/write mode
Read/write power is measured with the heads on track, while the head is reading/writing from/to disc. It is
performed with 100 percent duty cycle of read/write operation.
• Performance Idle mode
During Performance Idle mode, the heads are on track but no reading or writing is done. The spindle motor is
spinning at full speed.
• Low power idle mode
During Low power Idle mode, the heads are unloaded but the spindle motor is spinning at full speed. Servo
and read/write electronics are in powered down mode.
• Standby / Sleep mode
During Standby/Sleep mode, the spindle motor is not spinning, and the servo and read/write electronics are
in powered down mode.
6
Lyrion Series IDE Product Manual, Rev. B
Table 2:
DC power
Power Consumption at 3.3V
Startup (max*)
Average (W)
1.15
1.0
Read
Write
0.9
Performance idle (typical)
Low power idle (typical)
Standby/Sleep (typical)
0.5
0.3
0.08
*Maximum is the average of the peak value in 10 msec window
2.7.1.1
Typical current profile
Figure 2.
Typical 3.3V startup and operation current profile
Lyrion Series IDE Product Manual, Rev. B
7
2.7.2
Conducted noise
Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on
the +3.3 volt line.
Using 3.3-volt power, the drive is expected to operate with a maximum of 70 mV peak-to-peak square-wave
injected noise at up to 20 MHz.
Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write
current.
2.7.3
Voltage tolerance and Maximum current
Voltage tolerance (including noise):
3.3V ± 5%
Maximum Current (peak-to-peak):
500mA
8
Lyrion Series IDE Product Manual, Rev. B
2.7.4
Power-management modes
The drive provides programmable power management to provide greater energy efficiency. The drive features
the following power-management modes:
Table 3:
Power-management modes
Power modes
Heads
Spindle
Rotating
Rotating
Rotating
Stopped
Buffer
Active (read/write/seek) Tracking
Enabled
Enabled
Disabled
Disabled
Idle, performance
Idle, low power
Standby/Sleep
Tracking
Parked
Parked
• Active mode
The drive is in Active mode during the read/write and seek operations.
• Performance idle mode
The drive enters this mode once the read/write/seek activity is completed. The buffer remains enabled, and
the drive accepts all commands and returns to Active mode any time disc access is necessary.
• Low power idle mode
Drive enters Low Power Idle mode from Performance Idle mode when the Advanced Power Management
Level is set between 80h and FDh, and the Idle timer reaches 15 seconds. Disc is spinning and heads are
parked and drive accepts all commands and returns to Active mode any time disc access is necessary.
• Standby/Sleep mode
The drive enters Standby mode when the host sends a Standby Immediate command. In Standby mode, the
drive buffer is disabled, the heads are parked and the spindle is at rest. The drive accepts all commands and
returns to Active mode any time disc access is necessary.
Lyrion Series IDE Product Manual, Rev. B
9
2.8
Environmental specifications
Ambient temperature
2.8.1
Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.
Actual drive case temperature should not exceed 70°C (158°F) within the operating ambient conditions. Case
temperature of the drive operating at 60°C ambient may hit a maximum of 70°C at certain parts of the casing.
Above 1,000 feet (305 meters), the maximum operating temperature is derated linearly by 1°C every 1000 feet.
Operating
0° to 60°C (32° to 140°F)
(70°C max case temperature)
Nonoperating
–40° to 70°C (–40° to 158°F)
2.8.2
Temperature gradient
Operating
20°C per hour (36°F per hour max), without condensation
30°C per hour (54°F per hour max), without condensation
Nonoperating
2.8.3
Humidity
2.8.3.1
Relative humidity
Operating 5% to 90% noncondensing (30% per hour max)
Nonoperating 5% to 95% noncondensing (30% per hour max)
2.8.3.2
Wet bulb temperature
[1] Operating: Wet bulb temperature is calculated by the operating Temperature and the Relative Humidity levels.
[2] Nonoperating: Wet bulb temperature is calculated by the nonoperating Temperature and the Relative Humidity levels.
2.8.4
Altitude
Operating
–60.98 m to 3,048 m (–200 ft to 10,000+ ft)
–60.98 to 12,192 m (–200 ft to 40,000+ ft)
Nonoperating
10
Lyrion Series IDE Product Manual, Rev. B
2.8.5
Shock
All shock measurements in this section are carried out at drive level. For all linear shock test, operating or
nonoperating, the input shock level is measured at the frame of the drive at the specific location as indicated in
Figure 3 below.
Shock Monitoring Position
Figure 3.
Location where tri-axial accelerometer will be placed on Lyrion Series drives
All shock test cover all the 6 directions, +/- x, y and z axes. The drive axis definition in shown in Figure 4 below.
-Z
-X
-Y
+X
+Y
+Z
Figure 4.
2.8.5.1
Drive axis definition for Lyrion Series drives
Operating shock
The drive is subjected to 10 shocks for each direction. During the shocks, there must be a minimum delay of 3
seconds between shock pulses. Soft errors and automatic retries are allowed during the test. No data loss or
permanent damage occurs during a half sine shock pulse of:
500 G, 2 msec
2.8.5.2
Nonoperating shock
The nonoperating shock level that the drive can experience without incurring any physical damage when sub-
sequently put into operation is 1500 Gs. The same applies for shock levels of 1500 G, 1 msec pulse duration
on fresh drives for each level.
2.8.6
Vibration
All vibration specifications assume that the drive is mounted securely in a fixture that does not have fixture
resonances in the frequency test range.
Lyrion Series IDE Product Manual, Rev. B
11
2.8.6.1
Operating sweep sine vibration
The following lists the maximum operating sweep sine vibration levels that the drive may experience while
meeting the performance standards specified. It consists of a forward and backward sweep from 10 Hz to
500 Hz to 10 Hz. The drive operates without a hard error while being subjected to the following vibration levels.
10 Hz to 500 Hz @ 2 oct/min
1.0 Gs (0 to pk). Maximum displacement may apply below 10 Hz.
2.8.6.2
Operating random vibration
The test consists of 30 minutes of random vibration using the power spectral density (PSD) levels specified in
the table below. The vibration test level is 0.67 Gs RMS. The drive operates without a hard error while being
subjected to the following vibration levels.
Table 4:
Operating random vibration profile
Frequency (Hz)
G2/Hz
17
45
1.1 x E-03
1.1 x E-03
8.0 x E-03
8.0 x E-03
1.0 x E-03
1.0 x E-03
5.0 x E-04
5.0 x E-04
48
62
65
150
200
500
2.8.6.3
Nonoperating sweep sine vibration
The following table lists the maximum nonoperating sweep sine vibration levels that the drive may experience
while meeting the performance standards specified. It consists of a forward and backward sweep from 5 Hz to
500 Hz to 5 Hz. The drive does not incur any physical damage when subsequently put into operation.
10 Hz to 500 Hz @ 0.5 oct/min
5 Hz to 10 Hz
5.0 Gs (0 to pk). Maximum displacement may apply below 22 Hz.
25.4 mm peak to peak displacement.
12
Lyrion Series IDE Product Manual, Rev. B
2.8.6.4
Nonoperating random vibration
The test consists of 15 minutes of random vibration using the power spectral density (PSD) levels specified in
the table below. The vibration test level is 3.01 Gs RMS. The drive does not incur any physical damage when
subsequently put into operation.
Table 5:
Nonoperating random vibration profile.
Frequency (Hz)
G2/Hz
2.5
5
1.0 x E-03
3.0 x E-02
1.8 x E-02
1.8 x E-02
40
500
2.8.7
Corrosive environment
Seagate electronic drive components pass accelerated corrosion testing equivalent to ten years of exposure to
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM
B845. However, this accelerated testing cannot duplicate every potential application environment.
Users should use caution exposing any electronic components to uncontrolled chemical pollutants and corro-
sive chemicals as electronic drive component reliability can be affected by the installation environment. The sil-
ver, copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide,
chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or
exposed to an ambient relative humidity greater than 95 percent. Materials used in cabinet fabrication, such as
vulcanized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of
any electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.
Lyrion Series IDE Product Manual, Rev. B
13
2.9
Acoustics
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). Discrete
tone penalties are added to the A-weighted sound power (LW) with the following formula only when determin-
ing compliance:
LWt(spec) == LW + 0.1Pt + 0.3 < 4.0 (Bels)
where
LW = A-weighted sound power level
pt == Value of discrete tone penalty [==dLt-6.0 (dBA)]
dLt = Tone-to-noise ratio taken in accordance with ISO 7779 at each octave band.
All measurements are consistent with ISO document 7779. Sound power measurements are taken under
essentially free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing
upward.)
Table 6:
Drive level acoustics
Acoustic mode
Idle
Operational
1.6 bels (typ)
2.2 bels (typ)
2.10
Electromagnetic immunity
When properly installed in a representative host system, the drive operates without errors or degradation in
performance when subjected to the radio frequency (RF) environments defined in the following table:
Table 7:
Electromagnetic immunity
Performance
level
Reference
standard
Test
Description
Radiated RF immunity
80 to 1,000 MHz, 3 V/m,
80% AM with 1 kHz sine
900 MHz, 3 V/m, 50% pulse modulation @ 200
Hz
A
EN 61000-4-3: 96
ENV 50204: 95
Electrical fast transient
Surge immunity
± 1 kV on AC mains, ± 0.5 kV on external I/O
± 1 kV differential, ± 2 kV common, AC mains
B
B
A
EN 61000-4-4: 95
EN 61000-4-5: 95
EN 61000-4-6: 97
Conducted RF immunity
150 kHz to 80 MHz, 3 Vrms, 80% AM with 1
kHz sine
Voltage dips, interrupts
0% open, 5 seconds
0% short, 5 seconds
40%, 0.10 seconds
70%, 0.01 seconds
C
C
C
B
EN 61000-4-11: 94
2.11
Reliability
Measurement type
Specification
14
Nonrecoverable read errors
Load/Unload (LUL) cycles
1 per 10 bits read, max.
20,000 power loss
14
Lyrion Series IDE Product Manual, Rev. B
2.12
Agency certification
Safety certification
2.12.1
The drives are recognized in accordance with UL60950-1, CAN/CSA-C22.2 No.60950-1, EN60950 and IEC
60950.
2.12.2
Electromagnetic compatibility
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-
tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product
standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and
the immunity levels are defined by EN 55024.
Seagate uses an independent laboratory to confirm compliance with the EC directives specified in the previous
paragraph. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply
with the directives when used in the test systems, we cannot guarantee that all systems will comply with the
directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O
cable (if necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators
should confirm EMC compliance and provide CE marking for their products.
Korean RRL
If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-
graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic
Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information
and Communication Republic of Korea.
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil-
ity (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recog-
nized lab.
• Family name:
Lyrion Series
STX-S181 (B)
• Certificate numbers:
Australian C-Tick (N176)
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548
1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communi-
cation Authority (ACA).
2.12.3
European Union Restriction of Hazardous Substances (RoHS) Directive
Seagate designs its products to meet environmental protection requirements worldwide, including regulations
restricting certain chemical substances. A new law, the European Union Restriction of Hazardous Substances
(RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium, Mercury,
Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This drive is manufactured
with components and materials that comply with the RoHS Directive.
Lyrion Series IDE Product Manual, Rev. B
15
2.12.4
2.12.4
China Restriction of Hazardous Substances (RoHS) Directive
中国限制危险物品的指令
This product has an Environmental Protection Use Period (EPUP) of 20 years. The following
table contains information mandated by China's "Marking Requirements for Control of Pollution
Caused by Electronic Information Products" Standard.
"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower
than the threshold defined by the China RoHS MCV Standard.
“O"表示该部件（于同类物品程度上）所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。
"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over
the threshold defined by the China RoHS MCV Standard.
“X "表示该部件（于同类物品程度上）所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。
2.12.5
FCC verification
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached
as an external device). As such, each drive is considered to be a subassembly even when it is individually mar-
keted to the customer. As a subassembly, no Federal Communications Commission verification or certification
of the device is required.
Seagate Technology LLC has tested this device in enclosures as described above to ensure that the total
assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B
computing device, pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is
likely to result in interference to radio and television reception.
Radio and television interference. This equipment generates and uses radio frequency energy and if not
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio
and television reception.
This equipment is designed to provide reasonable protection against such interference in a residential installa-
tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause interference to radio or television, which can be determined by turning the equipment on and off,
you are encouraged to try one or more of the following corrective measures:
• Reorient the receiving antenna.
• Move the device to one side or the other of the radio or TV.
• Move the device farther away from the radio or TV.
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.
16
Lyrion Series IDE Product Manual, Rev. B
If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-
gestions. You may find helpful the following booklet prepared by the Federal Communications Commission:
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super-
intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num-
ber 004-000-00345-4.
Lyrion Series IDE Product Manual, Rev. B
17
18
Lyrion Series IDE Product Manual, Rev. B
3.0
Configuring and mounting the drive
This section contains the specifications and instructions for configuring and mounting the drive.
3.1
Handling and static discharge precautions
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic
discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions:
Caution:
• Do not cover or seal the breather hole! Covering or sealing the breather hole may result in loss of data.
Figure 5.
Lyrion Series breather hole location
• Keep the drive in the electrostatic discharge (ESD) bag until you are ready for installation to limit the drive’s
exposure to ESD.
• Before handling the drives, put on a grounded wrist strap, or ground yourself frequently by touching the metal
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire
installation procedure.
• Handle the drive only by its edges or frame.
Figure 6.
Lyrion Series proper handling example
• The drive is fragile—handle it with care. Do not press down on the drive top cover or attempt to use a pen to
write on the drive’s label.
• Do not apply more than 6.8N of force to the top cover.
• Always rest the drives on a padded, antistatic surface until you mount it in the system.
Lyrion Series IDE Product Manual, Rev. B
19
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are
used to seal out dirt and contamination.
• If provided, store drive in the protective casing when not in use.
• Turn the power off before installing or removing the drive.
• Do not apply any force to the drive during handling or installation.
• Do not touch the connector pins or the printed circuit board.
• Do not drop the drive.
• Do not expose the drive to wet conditions.
• Do not place the drive near a strong magnetic field.
• Do not expose the drive to extreme temperatures.
• The drive may become hot during operation. Be careful when removing the drive from the host device
immediately after operation.
20
Lyrion Series IDE Product Manual, Rev. B
3.2
Drive installation
Follow these installation precautions when inserting the drive:
• Follow instructions for the installation of data storage devices, provided with your device’s user manual.
• Handle the drive only by its edges or frame or designated finger grip region during mounting (see Figure 6).
Temperature Measurement Position
X
Figure 7.
Lyrion Series mechanical dimensions—top, side and end view
Lyrion Series IDE Product Manual, Rev. B
21
3.3
Mounting considerations
• Use an elastic mounting material to protect drives so as to ensure that more shock can be absorbed.
• There are guides along the side for mounting. Refer to figure on areas (refer to Figure 8, shaded area)
where the mounting material can rest for mounting.
• As the drive is a sensitive device, it is not recommended to have any mounting force on the top and bottom
surface of the drive other than the recommended mounting surfaces. Mounting force on non recommended
surfaces shall not exceed 6.8N.”
• The drive can be operated in any orientation but horizontal or vertical orientation is preferred.
• Allow a minimum clearance of 0.012 inches (0.30 mm) around the entire perimeter of the drive for cooling,
with the exception of the mounting edges for better airflow.
• In case the system design warrants bending of the FPC to the hard disc drive, care should be taken to
maximize the radius.
• Mounting materials are available from many third-party vendors.
• The 40-way connector is design to meet minimum 6N Horizontal FPC retention after mating.
• The connector has a specification of 20 insertion cycles.
Note. Drive thickness (t) around Bumper Region with Screw : 3.404 ± 0.200 mm
Drive thickness (t) around Bumper Region without Screw : 3.308 ± 0.200 mm
Figure 8.
Lyrion Series Area for Protective Mounting
22
Lyrion Series IDE Product Manual, Rev. B
4.0
Interface description
The drives use the industry-standard ATA (IDE) interface. It supports ATA programmed input/output (PIO)
modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–4.
4.1
Connector interface signals and connector pins
The following table summarizes the signals on the 40-way ZIF ATA interface connector.
Table 8:
40-way ZIF (IDE interface) connector signals
Pin number
Signal Name
Reserved
Reserved
RESET-
GROUND
DD07
Description
-
1
2
-
3
Hard Reset
Ground
4
5
Data bus bit 7
Data bus bit 8
Data bus bit 6
Data bus bit 9
Data bus bit 5
Data bus bit 10
Data bus bit 4
Data bus bit 11
Data bus bit 3
Data bus bit 12
Data bus bit 2
Data bus bit 13
Data bus bit 1
Data bus bit 14
Data bus bit 0
Data bus bit 15
Ground
6
DD08
7
DD06
8
DD09
9
DD05
10
11
12
13
14
15
16
17
18
19
20
21
22
DD10
DD04
DD11
DD03
DD12
DD02
DD13
DD01
DD14
DD00
DD15
GROUND
DMARQ
DMA request
Lyrion Series IDE Product Manual, Rev. B
23
Table 8:
40-way ZIF (IDE interface) connector signals
23
24
GROUND
Ground
DIOW- /
STOP
I/O Write to write to device registers or the data port
Stop during Ultra DMA burst
25
DIOR- /
HDMARDY- /
I/O Read to read device registers or the data port
Flow control during Ultra DMA data-in burst
HSTROBE
Data-out strobe signal for Ultra DMA data-out burst
26
27
GROUND
Ground
IORDY /
DDMARDY- /
DSTROBE
I/O Channel Ready during register access
Flow control during Ultra DMA data-out burst
Data-in strobe signal for Ultra DMA data-in burst
28
29
30
31
32
33
34
35
36
37
38
39
40
GROUND
DMACK-
INTRQ
DA01
Ground
DMA Acknowledge
Interrupt Request
Address bus bit 1
PDIAG-
DA00
-
Address bus bit 0
DA02
Address bus bit 2
CS0-
Chip Select 0
CS1-
Chip Select 1
DASP-
3.3V
Used to drive external LED when drive is accessed
Voltage input
Voltage input
-
3.3V
Reserved
24
Lyrion Series IDE Product Manual, Rev. B
4.2
Supported ATA commands
The following table lists ATA-standard commands that the drive supports. For a detailed description of the ATA
commands, refer to ATA version 7 specification, Volume 1. (www.t13.org)
Table 9:
Supported commands
Command Name
Command Op-Code Command Type
NOP
00h
10h
20h
24h
25h
27h
29h
30h
34h
35h
37h
39h
40h
42h
90h
92h
B0h
Non data
Recalibrate
Non data
Read Sector(s)
PIO data-in
PIO data-in
DMA data-in
Non data
Read Sector(s) Ext
Read DMA Ext
Read Native Max Address Ext
Read Multiple Ext
PIO data-in
PIO data-out
PIO data-out
DMA data-out
Non data
Write Sector(s)
Write Sector(s) Ext
Write DMA Ext
Set Max Address Ext
Write Multiple Ext
PIO data-out
Non data
Read Verify Sector(s)
Read Verify Sector(s) Ext
Execute Drive Diagnostics
Download Microcode
SMART
Non data
Non data
PIO data-out
SMART Disable Operations
SMART Enable/Disable Autosave
Non data
Non data
SMART Enable Operations
SMART Execute Off-Line Immediate
SMART Read Data
Non data
Non data
PIO data-in
PIO data-in
Non data
SMART Read Log
SMART Return Status
SMART Write Log
PIO data-out
Device Configuration
B1h
Device Configuration Restore
Device Configuration Freeze Lock
Device Configuration Identify
Device Configuration Set
Read Multiple
Non data
Non data
PIO data-in
PIO data-out
PIO data-in
PIO data-out
Non data
C4h
C5h
C6h
C8h
Write Multiple
Set Multiple Mode
Read DMA
DMA data-in
Lyrion Series IDE Product Manual, Rev. B
25
Table 9:
Supported commands
Write DMA
CAh
E0h
E1h
E2h
E3h
E4h
E5h
E6h
E7h
EAh
E8h
ECh
EFh
F1h
F2h
F3h
F4h
F5h
F6h
F8h
F9h
DMA data-out
Non data
Standby Immediate
Idle Immediate
Standby
Non data
Non data
Idle
Non data
Read Buffer
PIO data-in
Non data
Check Power Mode
Sleep
Non data
Flush Cache
Non data
Flush Cache Ext
Write Buffer
Non data
PIO data-out
PIO data-in
Non data
Identify Device
Set Features
Security Set Password
Security Unlock
Security Erase Prepare
Security Erase Unit
Security Freeze Lock
Security Disable Password
Read Native Max Address
Set Max Address
PIO data-out
PIO data-out
Non data
PIO data-out
Non data
PIO data-out
Non data
Non data
26
Lyrion Series IDE Product Manual, Rev. B
4.2.1
Identify Device command
The Identify Device command (command code EC ) transfers information about the drive to the host following
H
power up. The data is organized as a single 512-byte (256 word) block of data, whose contents are as shown
in the following table.
Word ATA specification
Value
0
General configuration information bit-significant information
0040h
Bit 15: 0 = ATA device
Bit 7: 1 = removable media
Bit 6: 1 = non-removable/fixed device
10–19 Serial number: (20 ASCII characters)
Serial number
Firmware revision
Model number
23–26 Firmware revision (8 ASCII character string)
27–46 Drive model number:
(40 ASCII characters, padded with blanks to end of string)
Bits 7-0: Maximum number of sectors transferred per interrupt on
47
8010h
2B00h
Read Multiple/ Write Multiple commands
49
Capabilities
Bit 13: 1= Standby timer values specified in ATA-7 are supported
Bit 11: 1= IORDY supported
Bit 10: 0= IORDY may not be disabled
Bit 9 : 1= LBA supported
Bit 8 : 1= DMA supported
53
59
Bit 2: 1= the fields reported in word 88 are valid
Bit 1: 1= the fields reported in words (70:64) are valid
0007h
0110h
Bit 8: 1= Multiple sector setting is valid
Bits 7-0: Current setting for number of sectors transferred during a
Read/Write Multiple command
60–61 Total number of user-addressable LBA sectors available
37E3E40h (30GB)
6FC7C80h (60GB)
63
Bit 10: 1= Multiword DMA mode 2 is selected
0= Multiword DMA mode 2 is not selected
Bit 9: 1= Multiword DMA mode 1 is selected
0= Multiword DMA mode 1 is not selected
Bit 8: 1= Multiword DMA mode 0 is selected
0= Multiword DMA mode 0 is not selected
Bit 2: 1= Multiword DMA mode 2 and below are supported
Bit 1: 1= Multiword DMA mode 1 and below are supported
Bit 0: 1= Multiword DMA mode 0 is supported
Bits 7-0: PIO modes supported
xxx7h
64
65
0003h
0078h
Minimum Multiword DMA transfer cycle time per word
Bits 15-0: Cycle time in nanoseconds
66
67
68
Recommended Multiword DMA transfer cycle time
Bits 15-0: Cycle time in nanoseconds
0078h
0078h
0078h
Minimum PIO transfer cycle time without flow control
Bits 15-0: Cycle time in nanoseconds
Minimum PIO transfer cycle time with IORDY flow control
Bits 15-0: Cycle time in nanoseconds
Lyrion Series IDE Product Manual, Rev. B
27
82
Command sets supported
746Bh
Bit 14: 1= NOP command supported
Bit 13: 1= READ BUFFER command supported
Bit 12: 1= WRITE BUFFER command supported
Bit 10: 1= Host Protected Area feature set supported
Bit 6: 1= Look-ahead supported
Bit 5: 1= Write cache supported
Bit 3: 1= Mandatory Power Management feature set supported
Bit 1: 1= SECURITY Mode feature set supported
Bit 0: 1= SMART feature set supported
83
Command sets supported
7D29h
Bit 13: 1= FLUSH CACHE EXT command supported
Bit 12: 1= Mandatory FLUSH CACHE command supported
Bit 11: 1= DEVICE CONFIGURATION overlay feature set supported
Bit 10: 1= 48-bit Address feature set supported
Bit 8: 1= SET MAX security extension supported
Bit 5: 1= Power up in Standby feature supported
Bit 3: 1= Advanced Power Management feature set supported
Bit 0: 1= DOWNLOAD MICROCODE command supported
84
Command set/feature supported extension
Bit 5: 1= General Purpose Logging feature supported
Bit 1: 1= SMART self-test supported
6063h
Bit 0: 1= SMART error logging supported
85
86
87
Command sets referred in word 82 enabled
xxxxh
xxxxh
6063h
Command sets referred in word 83 enabled
Command set/feature default
Bit 5: 1= General Purpose Logging feature supported
Bit 1: 1= SMART self-test supported
Bit 0: 1= SMART error logging supported
Bit 12: 1= Ultra DMA mode 4 is selected
0= Ultra DMA mode 4 is not selected
88
xx1Fh
Bit 11: 1= Ultra DMA mode 3 is selected
0= Ultra DMA mode 3 is not selected
Bit 10: 1= Ultra DMA mode 2 is selected
0= Ultra DMA mode 2 is not selected
Bit 9: 1= Ultra DMA mode 1 is selected
0= Ultra DMA mode 1 is not selected
Bit 8: 1= Ultra DMA mode 0 is selected
0= Ultra DMA mode 0 is not selected
Bit 4: 1= Ultra DMA mode 4 and below are supported
Bit 3: 1= Ultra DMA mode 3 and below are supported
Bit 2: 1= Ultra DMA mode 2 and below are supported
Bit 1: 1= Ultra DMA mode 1 and below are supported
Bit 0: 1= Ultra DMA mode 0 and below are supported
Current Advanced Power Management value (default)
91
C0C0h
100-103 Total number of user-addressable LBA sectors available for
48-bit addressing feature (48-bit addressing not supported)
37E3E40h (30GB)
6FC7C80h (60GB)
28
Lyrion Series IDE Product Manual, Rev. B
The 512-byte data returned by the Identify Device command is shown in the table below. The last 256-byte are
vendor specific data and are for reference only.
Word No. Value Word No. Value Word No. Value Word No. Value Word No. Value Word No. Value
0
0040
3FFF
8C37
0010
0000
0000
003F
06FC
7C80
0000
2020
2020
2020
2020
2020
2020
xxxx
xxxx
xxxx
xxxx
0000
0000
0004
xxxx
xxxx
2020
2020
xxxx
xxxx
xxxx
xxxx
xxxx
2020
2020
2020
2020
2020
2020
2020
2020
2020
2020
2020
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
2020
2020
2020
2020
8010
0000
2B00
4000
0200
0000
0007
3FFF
0010
003F
FC10
00FB
0110
7C80
06FC
0000
0407
0003
0078
0078
0078
0078
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
00F0
0000
746b
7d29
6073
7469
86
87
3C29
6073
101F
002C
0000
C0C0
0001
100D
8080
0000
0000
0000
0000
0000
7C80
06FC
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0002
0000
0000
0000
0000
0000
0000
0000
0000
0209
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
7C80
06FC
7C80
06FC
2E30
3705
2CBE
0210
0000
3C03
3C1E
FFFF
400B
0000
0000
069C
02A0
0102
0000
0078
0618
0000
0000
0000
1212
0028
0000
0000
00C0
00E1
000A
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
0000
33A5
1
2
88
3
89
4
90
5
91
6
92
7
93
8
94
9
95
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Serial
Number
xxxx
Firmware
Revision
xxxx
xxxx
Drive
Model
Number
Lyrion Series IDE Product Manual, Rev. B
29
4.2.2
Set Features command
This command is used by the host to establish parameters that affect the execution of certain drive features.
The supported features determined by the value in the Features register are as shown in Table 10. Read look-
ahead and write cache are enabled by default upon power on.
Table 10: Features register values
Feature Description
02h
03h
Enable Write Cache
Set DMA and PIO transfer modes based on the value in the Sector Count register.
Sector Count register values
08h: Set PIO Transfer Mode 0
09h: Set PIO Transfer Mode 1
0Ah: Set PIO Transfer Mode 2
0Bh: Set PIO Transfer Mode 3
0Ch: Set PIO Transfer Mode 4
20h: Set Multiword Transfer Mode 0.
21h: Set Multiword Transfer Mode 1.
22h: Set Multiword Transfer Mode 2.
40h: Set Ultra DMA mode 0.
41h: Set Ultra DMA mode 1.
42h: Set Ultra DMA mode 2.
44h: Set Ultra DMA mode 4.
05h
Enable Advanced Power Management (APM) with APM level as in the Sector Count register .
Sector Count register values
0h : Reserved
1h – 7Fh : Allow Spin-Down (Standby Mode)
80h – FEh : Disallow Spin-Down (Low Power Idle Mode)
FFh : Reserved
55h
82h
85h
AAh
Disable Read Look-Ahead.
Disable Write Cache.
Disable Advanced Power Management (APM)
Enable Read Look-Ahead .
The following drive features are set after a Power On Reset, Hardware Reset or Software Reset.
Transfer mode : Write Cache :
Power On Reset
Hardware Reset
Software Reset
PIO 4, MDMA 2
PIO 4, MDMA 2
Current setting
Power On Reset
Hardware Reset
Software Reset
Enabled
Enabled
Current setting
Read look-ahead :
APM :
Power On Reset
Hardware Reset
Software Reset
Enabled
Enabled
Current setting
Power On Reset
Hardware Reset
Software Reset
C0h
Current setting
Current setting
30
Lyrion Series IDE Product Manual, Rev. B
4.3
Register default values
The following table descibes the taskfile register default values following Power On Reset, Hardware Reset
and Software Reset.
Table 11: Register default values
Power On Reset
Hardware Reset
Software Reset
Error register
01h
01h
01h
00h
00h
00h
50h
50h
01h
01h
01h
00h
00h
00h
50h
50h
01h
01h
01h
00h
00h
00h
50h
50h
Sector Count register
Sector Number register
Cylinder Lo register
Cylinder Hi register
Device/Head register
Status register
Alt Status register
Lyrion Series IDE Product Manual, Rev. B
31
32
Lyrion Series IDE Product Manual, Rev. B
5.0
Seagate Technology support services
Internet
For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is
available 24 hours daily by email for your questions.
Presales Support:
Technical Support:
Warranty Support:
mySeagate
my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides
self-service access to critical applications, personalized content and the tools that allow our partners to
manage their Seagate account functions. Submit pricing requests, orders and returns through a single,
password-protected Web interface-anytime, anywhere in the world.
spp.seagate.com
spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You
may register for customized communications that are not available on the web. These communications contain
product launch, EOL, pricing, promotions and other channel-related information. To learn more about the
benefits or to register, go to spp.seagate.com, any time, from anywhere in the world.
Seagate Service Centers
Presales Support
Our Presales Support staff can help you determine which Seagate products are best suited for your specific
application or computer system, as well as product availability and compatibility.
Technical Support
Seagate technical support is available to assist you online at support.seagate.com or through one of our call
centers. Have your system configuration information and your “ST” model number available.
SeaTDD™ (+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or
comments 24 hours daily and exchange messages with a technical support specialist during normal business
hours for the call center in your region.
Lyrion Series IDE Product Manual, Rev. B
33
Customer Service Operations
Warranty Service
Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct
customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-
related issues. Resellers or end users of drive products should contact their place of purchase or Seagate
warranty service for assistance. Have your serial number and model or part number available.
Data Recovery Services
Seagate offers data recovery services for all formats and all brands of storage media. Our data recovery
services labs are currently located throughout the world. . Additional information, including an online request
form and data loss prevention resources, is available at http://services.seagate.com/index.aspx
Authorized Service Centers
Seagate Service Centers are available on a global basis for the return of defective products. Contact your
customer support representative for the location nearest you.
USA/Canada/Latin America support services
For an extensive list of telephone numbers to technical support, presales and warranty service in USA/
Global Customer Support
Presales, Technical, and Warranty Support
Call Center
USA, Canada,
and Mexico
Toll-free
Direct dial
1-800-SEAGATE
+1-405-324-4700
Data Recovery Services
Call Center
Toll-free
Direct dial
FAX
USA, Canada,
and Mexico
1-800-475-01435
+1-905-474-2162
1-800-475-0158
+1-905-474-2459
Europe, the Middle East and Africa Support Services
For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the
Asia/Pacific Support Services
For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific,
34
Lyrion Series IDE Product Manual, Rev. B
Publication feedback survey
We are interested in your comments and suggestions regarding this publication. Please take a few minutes to
participate in our survey at the following URL:
Thank you for your time and comments.
Lyrion Series IDE Product Manual, Rev. B
35
36
Lyrion Series IDE Product Manual, Rev. B
Index
A
F
acoustics 14
frequency 14
altitude 10
G
H
B
BPI 5
handling 19
heads 1
height 5
humidity 10
C
I
interface 5
certification 15
commands 25
compliance 15
consumption 7
interference 16
Introduction 1
C-Tick 15
K
D
density 5
L
length 5
disclaimer 2
E
M
enclosures 16
EPRML 1
modes 23
errors 14
Lyrion Series IDE Product Manual, Rev. B
37
shock 11
signals 23
sound 14
specifications 3
Spinup 7
N
noise 8
Standby/Sleep 7
O
subassembly 16
P
pins 23
T
temperature 10
PIO 23
tort 2
precautions 21
V
Vibration 11
voltage 8
R
register 30
W
warranty 2
weight 5
width 5
reliability 14
resistance 8
RF 14
S
SeaTools 1
sectors 4
38
Lyrion Series IDE Product Manual, Rev. B
Seagate Technology LLC
920 Disc Drive, Scotts Valley, California 95066-4544, USA
Publication Number: 100462437, Rev. B, Printed in U.S.A.
|