Seagate CONSTELLATION ES2 SERIAL ATA ST33000652NS User Manual

Product Manual  
®
Constellation ES.2 Serial ATA  
Standard Model  
ST33000650NS  
Self-Encrypting Drive Model  
ST33000651NS  
SED FIPS 140-2 Model  
Review Pending  
ST33000652NS  
100633157  
Rev. D  
April 2011  
Contents  
6.2.3  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
i
7.3.3  
ii  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
1.0  
Seagate Technology support services  
SEAGATE ONLINE SUPPORT and SERVICES  
Available services include:  
Presales & Technical support  
Global Support Services telephone numbers & business hours  
Authorized Service Centers  
For information regarding Warranty Support, visit  
http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
1
   
2.0  
Introduction  
This manual describes the functional, mechanical and interface specifications for the following Seagate  
Constellation® ES.2 Serial ATA model drives:  
Model Number  
ST33000652NS  
ST33000651NS  
ST33000650NS  
Self-Encrypting Drive (SED)  
FIPS 140-2 Level 2 (Review Pending)  
Yes  
Yes  
No  
Yes  
No  
No  
These drives provide the following key features:  
• 7200 RPM spindle speed.  
• PowerChoice™ for selectable power savings  
Top Cover Attached motor for excellent vibration tolerance  
• High instantaneous (burst) data-transfer rates (up to 600MB per second).  
• Perpendicular recording technology provides the drives with increased areal density.  
• State-of-the-art cache and on-the-fly error-correction algorithms.  
• Native Command Queueing with command ordering to increase performance in demanding applications.  
• Full-track multiple-sector transfer capability without local processor intervention.  
• SeaTools™ diagnostic software performs a drive self-test that eliminates unnecessary drive returns.  
• Support for S.M.A.R.T. drive monitoring and reporting.  
• Supports latching SATA cables and connectors.  
• Worldwide Name (WWN) capability uniquely identifies the drive.  
Note. Seagate recommends validating your configuration with the selected HBA/RAID controller  
manufacturer to ensure full 3TB capacity capabilities.  
For more information on FIPS 140-2 Level 2 certification see See Section 5.0 on page 25 .  
2
Constellation ES.2 Serial ATA Product Manual, Rev. D  
         
2.1  
About the Serial ATA interface  
The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary  
advantages include:  
• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump-  
ers or other configuration options.  
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.  
• Scalability to higher performance levels.  
In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial  
ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current  
system and expect all of your existing applications to work as normal.  
The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host  
adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two  
drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they  
were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0  
(master) devices.  
Note. The host adapter may, optionally, emulate a master/slave environment to host software where two  
devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and  
Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a  
master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA  
environment.  
The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide  
backward compatibility with existing host systems and software. The Command and Control Block registers,  
PIO and DMA data transfers, resets, and interrupts are all emulated.  
The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device regis-  
ters, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For addi-  
tional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
3
       
3.0  
Drive specifications  
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal  
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the  
following drive models:  
Model Number  
ST33000652NS  
ST33000651NS  
ST33000650NS  
Self-Encrypting Drive (SED)  
FIPS 140-2 Level 2 (Review Pending)  
Yes  
Yes  
No  
Yes  
No  
No  
3.1  
Specification summary tables  
The specifications listed in the following tables are for quick reference. For details on specification measure-  
ment or definition, see the appropriate section of this manual.  
Table 1:  
Drive specifications summary  
Drive specification  
ST33000650NS  
ST33000651NS  
ST33000652NS  
Formatted (512 bytes/sector)*  
Guaranteed sectors  
3TB  
5,860,533,168  
Heads  
10  
Discs  
5
Bytes per sector  
512  
63  
Default sectors per track  
Default read/write heads  
Default cylinders  
16  
16,383  
1638  
270  
444  
7200  
1900  
Recording density, KBPI (Kb/in max)  
Track density, KTPI (ktracks/in avg.)  
Areal density, (Gb/in2 avg)  
Spindle speed (RPM)  
Internal data transfer rate  
(Mb/s max)  
Sustained data transfer rate OD  
(MB/s max)  
155  
600  
I/O data-transfer rate  
(MB/s max)  
ATA data-transfer modes supported  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
4
Constellation ES.2 Serial ATA Product Manual, Rev. D  
       
Drive specification  
ST33000650NS  
ST33000651NS  
ST33000652NS  
Cache buffer  
64MB  
Weight: (maximum)  
700g (1.543 lb)  
Average latency  
4.16ms  
15  
Power-on to ready (sec max)  
Standby to ready (sec max)  
Track-to-track seek time (ms typical)  
15  
0.5 read  
0.5 write  
Average seek, read (ms typical)  
Average seek, write (ms typical)  
Startup current (typical) 12V (peak)  
8.5  
9.5  
2.8A  
2.0A (optional configuration through Smart Command Transport)  
Voltage tolerance (including noise)  
Ambient temperature  
5V ±5%  
12V ±5%  
5° to 60°C (operating/tested)  
–40° to 70°C (nonoperating)  
Temperature gradient  
(°C per hour max)  
20°C (operating)  
30°C (nonoperating)  
Relative humidity  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Altitude, operating  
30% per hour max  
–60.96 m to 3,048 m  
(–200 ft to 10,000+ ft)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft to 40,000+ ft)  
Operational Shock (max at 2 ms)  
Non-Operational Shock (max at 2 ms)  
Vibration, operating  
Read 70 Gs / Write 40 Gs  
300 Gs  
5–22 Hz:  
0.25 Gs, Limited displacement  
22–350 Hz: 0.50 Gs  
350–500 Hz: 0.25 Gs  
Operation Rotational vibration  
Vibration, nonoperating  
Drive acoustics, sound power (bels)  
Idle**  
20–1500Hz: 12.5 rads/s²  
10–500 Hz: 4.9 Grms ref  
2.8 (typical)  
3.0 (max)  
Performance seek  
3.2 (typical)  
3.4 (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 sector per 1015 bits read  
0.73% based on 8760 POH  
To determine the warranty for a specific drive, use a web browser to access the following  
web page: support.seagate.com/customer/warranty_validation.jsp  
You will be asked to provide the drive serial number, model number (or part number) and  
country of purchase. After submitting this information, the system will display the warranty  
information for your drive.  
Load-unload cycles  
300,000 (25°C, 50% rel. humidity) (600,000 design life testing)  
Yes  
Supports Hotplug operation per  
Serial ATA Revision 2.6 specification  
*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
5
3.2  
Formatted capacity  
Formatted  
capacity*  
Guaranteed  
sectors  
Model  
Bytes per sector  
ST33000650NS  
ST33000651NS  
ST33000652NS  
3TB  
5,860,533,168  
512  
*One GB equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
3.2.1  
LBA mode  
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,  
where n is the number of guaranteed sectors as defined above.  
See Section 7.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-  
bit addressing support of drives with capacities over 137GB.  
3.3  
Default logical geometry  
Cylinders  
Read/write heads  
Sectors per track  
63  
16,383  
16  
LBA mode  
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,  
where n is the number of guaranteed sectors as defined above.  
3.4  
Recording and interface technology  
Interface  
Serial ATA (SATA)  
Recording method  
Perpendicular  
Recording density, KBPI (Kb/in max)  
Track density, KTPI (ktracks/in avg)  
1638  
270  
2
Areal density (Gb/in avg)  
444  
Spindle speed (RPM) (± 0.2%)  
7200  
Internal data transfer rate (Mb/s max)  
Sustained data transfer rate (MB/s max)  
I/O data-transfer rate (MB/s max)  
1900  
155  
600 (Ultra DMA mode 5)  
6
Constellation ES.2 Serial ATA Product Manual, Rev. D  
                                                     
3.5  
Physical characteristics  
Weight: (maximum)  
Cache buffer  
700g (1.543 lb)  
64MB (64,768KB)  
3.6  
Seek time  
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using  
drive diagnostics. The specifications in the table below are defined as follows:  
• Track-to-track seek time is an average of all possible single-track seeks in both directions.  
• Average seek time is a true statistical random average of at least 5000 measurements of seeks between  
random tracks, less overhead.  
*Typical seek times (ms)  
Track-to-track  
Read  
0.50  
8.5  
Write  
0.50  
9.5  
Average  
Average latency:  
4.16  
*Measured in performance mode.  
Note. These drives are designed to consistently meet the seek times represented in this manual. Physical  
seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted  
values. However, due to the manner in which these drives are formatted, benchmark tests that  
include command overhead or measure logical seeks may produce results that vary from these  
specifications.  
3.7  
Start/stop times  
3TB models  
15 (max)  
Power-on to Ready (sec)  
Standby to Ready (sec)  
15 (max)  
Ready to spindle stop (sec)  
20 (max)  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
7
                                         
3.8  
Power specifications  
The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 4 on page 23.  
3.8.1 Power consumption  
Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on  
an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient  
temperature.  
• Spinup power  
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating  
speed.  
• Seek mode  
During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and  
does not execute a read or write operation. Servo electronics are active. Seek mode power represents the  
worst-case power consumption, using only random seeks with read or write latency time. This mode is not  
typical and is provided for worst-case information.  
• Read/write power and current  
Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-ms  
delay, then a 16-sector read followed by a 32ms delay.  
• Operating power and current  
Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each  
10 reads) and 20 percent drive idle mode.  
• Idle mode power  
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in  
a random track location.  
• Standby mode  
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/  
write electronics are in power-down mode.  
8
Constellation ES.2 Serial ATA Product Manual, Rev. D  
                                             
Table 2:  
3000GB Drive DC power requirements  
+5V  
3.0Gb mode  
+12V  
6.0Gb mode  
+12V  
Voltage  
Power  
(Watts)  
7.68  
+5V  
Power  
(Watts)  
7.71  
Regulation  
± 5%  
± 5%  
Avg Idle Current *  
Advanced Idle Current *  
Idle_A  
0.36  
0.49  
0.37  
0.49  
0.15  
0.13  
0.13  
0.13  
0.50  
0.41  
0.24  
0.01  
6.73  
5.54  
3.55  
0.75  
0.16  
0.14  
0.14  
0.14  
0.50  
0.41  
0.24  
0.01  
6.76  
5.57  
3.59  
0.79  
Idle_B  
Idle_C  
Standby  
Transition Current *  
Idle_A (Active)  
0.80  
0.64  
0.74  
0.70  
0.13  
1.48  
1.29  
2.53  
2.89  
0.01  
21.76  
18.63  
34.01  
38.13  
0.75  
0.84  
0.70  
0.74  
0.68  
0.14  
1.48  
1.35  
2.51  
2.79  
0.01  
21.96  
19.68  
33.80  
36.82  
0.79  
Idle_B (Active)  
Idle_C (Active)  
Standby (Active)  
Average Sleep Current  
Maximum Start Current  
DC (peak DC)  
0.53  
0.68  
0.13  
2.04  
2.85  
0.01  
27.13  
37.53  
0.77  
0.54  
0.70  
0.14  
2.04  
2.79  
0.01  
27.18  
36.91  
0.82  
AC (Peak DC)  
Delayed Motor Start (DC max)  
Peak operating current (random read):  
Typical DC  
0.32  
0.32  
1.10  
0.75  
0.77  
1.76  
10.62  
10.82  
26.62  
0.33  
0.33  
1.14  
0.75  
0.76  
1.74  
10.68  
10.82  
26.58  
Maximum DC  
Maximum DC(peak)  
Peak operating current (random write)  
Typical DC  
0.43  
0.44  
0.96  
0.61  
0.62  
1.72  
9.53  
9.62  
25.44  
0.44  
0.44  
0.98  
0.61  
0.62  
1.72  
9.54  
9.64  
25.54  
Maximum DC  
Maximum DC(peak)  
Peak operating current (sequential read)  
Typical DC  
0.64  
0.65  
1.00  
0.48  
0.49  
0.74  
9.01  
9.11  
0.65  
0.66  
1.02  
0.48  
0.49  
0.72  
9.03  
9.17  
13.74  
Maximum DC  
Maximum DC(peak)  
Peak operating current (sequential write)  
Typical DC  
13.88  
0.73  
0.74  
0.98  
0.48  
0.49  
0.74  
9.45  
9.56  
13.78  
0.74  
0.74  
1.00  
0.48  
0.49  
0.82  
9.47  
9.61  
14.84  
Maximum DC  
Maximum DC(peak)  
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
9
     
3.8.1.1  
Typical current profiles  
Figure 1. Typical 5V startup and operation current profile  
10  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
 
Figure 2. Typical 12V startup and operation current profile  
3.8.2 Conducted noise  
Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on  
the +12 V line or an equivalent 15-ohm resistive load on the +5V line.  
• Using 12V power, the drive is expected to operate with a maximum of 120mV peak-to-peak square-wave  
injected noise at up to 10MHz.  
• Using 5V power, the drive is expected to operate with a maximum of 100mV peak-to-peak square-wave  
injected noise at up to 10MHz.  
Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write  
current.  
3.8.3  
Voltage tolerance  
Voltage tolerance (including noise):  
5V ± 5%  
12V ± 5%  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
11  
               
3.8.4  
Power-management modes  
The drive provides programmable power management to provide greater energy efficiency. In most systems,  
you can control power management through the system setup program. The drive features the following  
power-management modes:  
Power modes  
Active  
Heads  
Spindle  
Buffer  
Tracking  
ID Biased  
Parked  
Parked  
Parked  
Parked  
Rotating  
Enabled  
Enabled  
Enabled  
Enabled  
Enabled  
Disabled  
Idle_a  
Rotating  
Idle_b  
Rotating  
Idle_c  
Rotating at lower RPM  
Stopped  
Standby  
Sleep  
Stopped  
Active mode  
The drive is in Active mode during the read/write and seek operations.  
• Idle mode  
The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc  
access is necessary.  
Standby mode  
The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set  
the standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for  
a specifiable length of time. The standby timer delay is established using a Standby or Idle command. In  
Standby mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive  
accepts all commands and returns to Active mode any time disc access is necessary.  
• Sleep mode  
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive buf-  
fer is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it  
receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and  
enters Standby mode with all current translation parameters intact.  
• Idle and Standby timers  
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and  
begins counting down from its specified delay times to zero. If the standby timer reaches zero before any  
drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the  
drive accepts all commands and returns to Active mode when disc access is necessary.  
12  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
                             
3.8.4.1  
Extended Power Conditions - PowerChoiceTM  
Utilizing the load/unload architecture a programmable power management interface is provided to tailor sys-  
tems for reduced power consumption and performance requirements.  
The table below lists the supported power conditions available in PowerChoice. Power conditions are ordered  
from highest power consumption (and shortest recovery time) to lowest power consumption (and longest  
recovery time) as follows: Idle_a power >= Idle_b power >= Idle_c power >= Standby_z power. The further you  
go down in the table, the more power savings is actualized. For example, Idle_b results in greater power sav-  
ings than the Idle_a power condition. Standby results in the greatest power savings.  
Power Condition Name  
Power Condition ID  
Description  
Idle_a  
81  
82  
83  
00  
Reduced electronics  
H
H
H
H
Idle_b  
Heads unloaded. Disks spinning at full RPM  
Heads unloaded. Disks spinning at reduced RPM  
Heads unloaded. Motor stopped (disks not spinning)  
Idle_c  
Standby_z  
Each power condition has a set of current, saved and default settings. Default settings are not modifiable.  
Default and saved settings persist across power-on resets. The current settings do not persist across power-on  
resets. At the time of manufacture, the default, saved and current settings are in the Power Conditions log  
match.  
PowerChoice is invoked using one of two methods  
• Automatic power transitions which are triggered by expiration of individual power condition timers. These  
timer values may be customized and enabled using the Extended Power Conditions (EPC) feature set using  
the standardized Set Features command interface.  
• Immediate host commanded power transitions may be initiated using an EPC Set Features "Go to Power  
Condition" subcommand to enter any supported power condition. Legacy power commands Standby Imme-  
diate and Idle Immediate also provide a method to directly transition the drive into supported power condi-  
tions.  
PowerChoice exits power saving states under the following conditions  
• Any command which requires the drive to enter the PM0: Active state (media access)  
• Power on reset  
PowerChoice provides the following reporting methods for tracking purposes  
Check Power Mode Command  
• Reports the current power state of the drive  
Identify Device Command  
• EPC Feature set supported flag  
• EPC Feature enabled flag is set if at least one Idle power condition timer is enabled  
Power Condition Log reports the following for each power condition  
• Nominal recovery time from the power condition to active  
• If the power condition is Supported, Changeable, and Savable  
• Default enabled state, and timer value  
• Saved enabled state, and timer value  
• Current enabled state, and timer value  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
13  
S.M.A.R.T. Read Data Reports  
• Attribute 192 - Emergency Retract Count  
• Attribute 193 - Load/Unload Cycle Count  
PowerChoice Manufacture Default Power Condition Timer Values  
Default power condition timer values have been established to assure product reliability and data integrity. A  
minimum timer value threshold of two minutes ensures the appropriate amount of background drive mainte-  
nance activities occur. Attempting to set a timer values less than the specified minimum timer value threshold  
will result in an aborted EPC "Set Power Condition Timer" subcommand.  
Power Condition Name  
Manufacturer Default Timer Values  
Idle_a  
2 min  
Idle_b  
4 min  
Idle_c  
10 min  
15 min  
Standby_z  
Setting power condition timer values less than the manufacturer specified defaults or issuing the EPC "Go to  
Power Condition" subcommand at a rate exceeding the default timers may limit this products reliability and  
data integrity.  
PowerChoice Supported Extended Power Condition Feature Subcommands  
EPC Subcommand  
Description  
00  
01  
02  
03  
Restore Power Condition Settings  
Go to Power Condition  
Set Power Condition Timer  
Set Power Condition State  
H
H
H
H
PowerChoice Supported Extended Power Condition Indentifiers  
Power Condition Identifiers  
00  
Power Condition Name  
Standby_z  
H
01 - 80  
Reserved  
H
81  
82  
83  
Idle_a  
H
H
H
Idle_b  
Idle_c  
84 - FE  
Reserved  
H
FF  
All EPC Power Conditions  
H
14  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
3.9  
Environmental limits  
Temperature and humidity values experienced by the drive must be such that condensation does not occur on  
any drive part. Altitude and atmospheric pressure specifications are referenced to a standard day at 58.7°F  
(14.8°C). Maximum wet bulb temperature is 82°F (28°C).  
3.9.1  
Temperature  
a. Operating  
The drive meets the operating specifications over a 41°F to 140°F (5°C to 60°C) drive case temperature  
range with a maximum temperature gradient of 36°F (20°C) per hour.  
The maximum allowable drive case temperature is 60°C. See Figure 3 for HDA case temperature  
measurement location  
The MTBF specification for the drive assumes the operating environment is designed to maintain nominal  
case temperature. The rated MTBF is based upon a sustained case temperature of 104°F (40°C).  
Occasional excursions in operating temperature between the rated MTBF temperature and the maximum  
drive operating case temperature may occur without impact to the rated MTBF temperature. However,  
continual or sustained operation at case temperatures beyond the rated MTBF temperature will degrade the  
drive MTBF and reduce product reliability.  
Air flow may be required to achieve consistent nominal case temperature values (see Section 4.4). To  
confirm that the required cooling is provided for the electronics and HDA, place the drive in its final  
mechanical configuration, and perform random write/read operations. After the temperatures stabilize,  
measure the case temperature of the drive.  
b. Non-operating  
–40° to 158°F (–40° to 70°C) package ambient with a maximum gradient of 36°F (20°C) per hour. This  
specification assumes that the drive is packaged in the shipping container designed by Seagate for use with  
drive.  
HDA Temp.  
Check Point  
Figure 3. Location of the HDA temperature check point  
Note. Image is for reference only, may not represent actual drive  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
15  
                     
3.9.2  
Humidity  
3.9.2.1  
Relative humidity  
Operating:  
Nonoperating:  
5% to 90% noncondensing (30% per hour max)  
5% to 95% noncondensing (30% per hour max)  
3.9.3  
Altitude  
Operating:  
–60.96 m to 3,048 m (–200 ft. to 10,000+ ft.)  
–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)  
Nonoperating:  
3.9.4  
Shock  
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive  
mounting screws. Shock may be applied in the X, Y or Z axis.  
3.9.4.1  
Operating shock  
These drives comply with the performance levels specified in this document when subjected to a maximum  
operating shock of 70 Gs (read) and 40 Gs (write) based on half-sine shock pulses of 2ms. Shocks should not  
be repeated more than two times per second.  
3.9.4.2  
Nonoperating shock  
The nonoperating shock level that the drive can experience without incurring physical damage or degradation  
in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse  
of 2ms duration.  
3.9.5  
Vibration  
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the  
drive mounting screws. Vibration may be applied in the X, Y or Z axis.  
3.9.5.1  
Operating vibration  
The maximum vibration levels that the drive may experience while meeting the performance standards speci-  
fied in this document are specified below.  
5–22 Hz  
0.25 Gs  
0.50 Gs  
0.25 Gs  
22–350 Hz  
350–500 Hz  
20 - 1500Hz  
*(RROV)  
2
12.5 rads/s w/RVFF  
* Rotary Random Operating Vibration  
3.9.5.2 Nonoperating vibration  
The maximum nonoperating vibration levels that the drive may experience without incurring physical damage  
or degradation in performance when subsequently put into operation are specified below.  
10–500 Hz  
Linear Random  
4.9 Grms ref  
16  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
                             
3.10  
Acoustics  
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-  
surements are consistent with ISO document 7779. Sound power measurements are taken under essentially  
free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.  
Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined  
by the following equation:  
(Number of seeks per second = 0.4 / (average latency + average access time)  
Table 3:  
Fluid Dynamic Bearing (FDB) motor acoustics  
Idle*  
Performance seek  
ST33000650NS  
ST33000651NS  
ST33000652NS  
2.8 bels (typ)  
3.0 bels (max)  
3.2 bels (typ)  
3.4 bels (max)  
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
3.11  
Test for Prominent Discrete Tones (PDTs)  
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this  
process is the use of the absolute threshold of hearing. Seagate uses this threshold curve (originated in ISO  
389-7) to discern tone audibility and to compensate for the inaudible components of sound prior to computation  
of tone ratios according to Annex D of the ECMA-74 standards.  
3.12  
Electromagnetic immunity  
When properly installed in a representative host system, the drive operates without errors or degradation in  
performance when subjected to the radio frequency (RF) environments defined in the following table:  
Table 4:  
Test  
Radio frequency environments  
Description  
Performance level  
Reference standard  
Electrostatic  
discharge  
Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV  
B
EN 61000-4-2: 95  
Radiated RF  
immunity  
80 to 1000 MHz, 3 V/m,  
A
B
EN 61000-4-3: 96  
ENV 50204: 95  
80% AM with 1 kHz sine  
900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz  
Electrical fast  
transient  
± 1 kV on AC mains, ± 0.5 kV on external I/O  
EN 61000-4-4: 95  
Surge immunity ± 1 kV differential, ± 2 kV common, AC mains  
B
A
EN 61000-4-5: 95  
EN 61000-4-6: 97  
Conducted RF  
immunity  
150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine  
Voltage dips,  
interrupts  
0% open, 5 seconds  
0% short, 5 seconds  
40%, 0.10 seconds  
70%, 0.01 seconds  
C
C
C
B
EN 61000-4-11: 94  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
17  
                                   
3.13  
Reliability  
3.13.1  
Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)  
The product shall achieve an Annualized Failure Rate (AFR) of 0.73% (MTBF of 1.2 million hours) when oper-  
ated nominal power and typical case temperatures of 40°C. Operation at temperatures outside the specifica-  
tions in Section 3.9 may increase the product AFR (decrease MTBF). AFR and MTBF are population statistics  
that are not relevant to individual units.  
AFR and MTBF specifications are based on the following assumptions for business critical storage system  
environments:  
• 8760 power-on-hours per year.  
• Operations at nominal voltages.  
Temperatures outside the specifications in Section 3.9 may reduce thee product reliability.  
• Normal I/O duty cycle for enterprise nearline applications. Operation at excessive I/O duty cycle may  
degrade product reliability.  
The enterprise application nearline environment of power-on-hours, temperature, and I/O duty cycle affect the  
product AFR and MTBF.  
15  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Load unload cycles  
1 per 10 bits read, max  
0.73% (nominal power, 40°C case temperature)  
300,000 cycles  
Warranty  
To determine the warranty for a specific drive, use a web browser to access the  
following web page: support.seagate.com/customer/warranty_validation.jsp  
From this page, click on the "Verify Your Warranty" link. You will be asked to provide  
the drive serial number, model number (or part number) and country of purchase.The  
system will display the warranty information for your drive.  
Preventive maintenance  
None required.  
3.14  
Agency certification  
3.14.1  
Safety certification  
These products are certified to meet the requirements of UL60950-1, CSA60950-1 and EN60950 and so  
marked as to the certify agency.  
3.14.2  
Electromagnetic compatibility  
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-  
tromagnetic Compatibility Directive (2004/108/EC) as put into place 20 July 2007. Testing is performed to the  
levels specified by the product standards for Information Technology Equipment (ITE). Emission levels are  
defined by EN 55022, Class B and the immunity levels are defined by EN 55024.  
Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the  
directives when used in the test systems, we cannot guarantee that all systems will comply with the directives.  
The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if  
necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should  
confirm EMC compliance and provide CE marking for their products.  
18  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
                                                     
Korean RRL  
If these drives have the Korean Communications Commission (KCC) logo, they comply with paragraph 1 of  
Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic Compatibility  
(EMC) Framework requirements of the Radio Research Laboratory (RRL) Communications Commission,  
Republic of Korea.  
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic  
Susceptibility (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a  
Korean-recognized lab.  
• Family name: Constellation ES.2 Serial ATA  
• Certificate number: STX-Constell-ES (B)  
• Date of Certification: August 20, 2009  
Australian C-Tick (N176)  
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZ  
CISPR22 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian  
Communication Authority (ACA).  
3.14.3  
FCC verification  
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached  
as an external device). As such, each drive is considered to be a subassembly even when it is individually  
marketed to the customer. As a subassembly, no Federal Communications Commission verification or  
certification of the device is required.  
Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure,  
disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device,  
pursuant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in  
interference to radio and television reception.  
Radio and television interference. This equipment generates and uses radio frequency energy and if not  
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio  
and television reception.  
This equipment is designed to provide reasonable protection against such interference in a residential  
installation. However, there is no guarantee that interference will not occur in a particular installation. If this  
equipment does cause interference to radio or television, which can be determined by turning the equipment  
on and off, you are encouraged to try one or more of the following corrective measures:  
• Reorient the receiving antenna.  
• Move the device to one side or the other of the radio or TV.  
• Move the device farther away from the radio or TV.  
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.  
If necessary, you should consult your dealer or an experienced radio/television technician for additional  
suggestions. You may find helpful the following booklet prepared by the Federal Communications Commission:  
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super-  
intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num-  
ber 004-000-00345-4.  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
19  
                               
3.15  
Environmental protection  
Seagate designs its products to meet environmental protection requirements worldwide, including regulations  
restricting certain chemical substances.  
3.15.1  
European Union Restriction of Hazardous Substances (RoHS) Directive  
Seagate designs its products to meet environmental protection requirements worldwide, including regulations  
restricting certain chemical substances. A new law, the European Union Restriction of Hazardous Substances  
(RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium, Mercury,  
Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This drive is manufactured  
with components and materials that comply with the RoHS Directive.  
中国限制危险物品的指令  
China Restriction of Hazardous Substances (RoHS) Directive  
3.15.2  
This product has an Environmental Protection Use Period (EPUP) of 20 years. The following  
table contains information mandated by China's "Marking Requirements for Control of Pollution  
Caused by Electronic Information Products" Standard.  
"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower  
than the threshold defined by the China RoHS MCV Standard.  
O"  
RoHS MCV  
表示该部件(于同类物品程度上)所含的危险和有毒物质低于中国  
标准所定义的门槛值。  
"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over  
the threshold defined by the China RoHS MCV Standard.  
X "  
RoHS MCV  
表示该部件(于同类物品程度上)所含的危险和有毒物质超出中国  
标准所定义的门槛值。  
3.16  
Corrosive environment  
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to  
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM  
B845. However, this accelerated testing cannot duplicate every potential application environment. Users  
should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive  
chemicals as electronic drive component reliability can be affected by the installation environment. The silver,  
copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chlo-  
ride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components  
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or  
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca-  
nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any  
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.  
20  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
               
3.17  
Reference documents  
Self-Encrypting Drives Reference Manual  
Seagate part number: 100515636  
Trusted Computing Group (TCG) Documents (apply to Self-Encrypting Drive models only)  
TCG Storage Architecture Core Specification, Rev. 1.0  
TCG Storage Security Subsystem Class Enterprise Specification, Rev. 1.0  
In case of conflict between this document and any referenced document, this document takes precedence.  
3.18  
Product warranty  
Beginning on the date of shipment to the customer and continuing for the period specified in your purchase  
contract, Seagate warrants that each product (including components and subassemblies) that fails to function  
properly under normal use due to defect in materials or workmanship or due to nonconformance to the applica-  
ble specifications will be repaired or replaced, at Seagate’s option and at no charge to the customer, if returned  
by customer at customer’s expense to Seagate’s designated facility in accordance with Seagate’s warranty  
procedure. Seagate will pay for transporting the repair or replacement item to the customer. For more detailed  
warranty information, refer to the standard terms and conditions of purchase for Seagate products on your pur-  
chase documentation.  
The remaining warranty for a particular drive can be determined by calling Seagate Customer Service at 1-  
800-468-3472. You can also determine remaining warranty using the Seagate web site (www.seagate.com).  
The drive serial number is required to determine remaining warranty information.  
Shipping  
When transporting or shipping a drive, use only a Seagate-approved container. Keep your original box. Sea-  
gate approved containers are easily identified by the Seagate Approved Package label. Shipping a drive in a  
non-approved container voids the drive warranty.  
Seagate repair centers may refuse receipt of components improperly packaged or obviously damaged in tran-  
sit. Contact your authorized Seagate distributor to purchase additional boxes. Seagate recommends shipping  
by an air-ride carrier experienced in handling computer equipment.  
Storage  
The maximum recommended storage period for the drive in a non-operational environment is 90 days. Drives  
should be stored in the original unopened Seagate shipping packaging whenever possible. Once the drive is  
removed from the Seagate original packaging the recommended maximum period between drive operation  
cycles is 30 days. During any storage period the drive non-operational temperature, humidity, wet bulb, atmo-  
spheric conditions, shock, vibration, magnetic and electrical field specifications should be followed.  
Product repair and return information  
Seagate customer service centers are the only facilities authorized to service Seagate drives. Seagate does  
not sanction any third-party repair facilities. Any unauthorized repair or tampering with the factory seal voids  
the warranty.  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
21  
     
4.0  
Configuring and mounting the drive  
This section contains the specifications and instructions for configuring and mounting the drive.  
4.1  
Handling and static-discharge precautions  
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-  
charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:  
Caution:  
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal  
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire  
installation procedure.  
• Handle the drive by its edges or frame only.  
• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.  
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.  
• Do not touch the connector pins or the printed circuit board.  
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids  
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are  
used to seal out dirt and contamination.  
22  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
                   
4.2  
Configuring the drive  
Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no  
master/slave relationship because each drive is considered a master in a point-to-point relationship. If two  
drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they  
were both “masters” on two separate ports. Both drives behave as if they are Device 0 (master) devices.  
4.3  
Serial ATA cables and connectors  
The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connec-  
tions. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 in). See Table 5 for  
connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.  
For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive  
and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind  
mateable.  
For installations which require cables, you can connect the drive as illustrated in Figure 4.  
Signal connector  
Power connector  
Signal cable  
Power cable  
Figure 4. Attaching SATA cabling  
Each cable is keyed to ensure correct orientation. Constellation ES.2 Serial ATA drives support latching SATA  
connectors.  
4.4  
Drive mounting  
You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-  
mounting holes. See Figure 5 for drive mounting dimensions. Follow these important mounting precautions when  
mounting the drive:  
• Allow a minimum clearance of 0.030 in (0.76mm) around the entire perimeter of the drive for cooling.  
• Use only 6-32 UNC mounting screws.  
• The screws should be inserted no more than 0.150 in (3.81mm) into the bottom or side mounting holes.  
• Do not overtighten the mounting screws (maximum torque: 6 in-lb).  
• Do not cover breather hole on top cover.  
Breather Hole  
Do Not  
Cover  
Breather hole location - top cover  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
23  
               
4.4.1  
Refer to Figure 5 for detailed mounting configuration dimensions. See Section 4.4, “Drive mounting.”  
Weight: 1.543 lb 700 g  
Mechanical specifications  
in  
mm  
in  
mm  
Breather  
Hole  
in  
mm  
Figure 5. Mounting dimensions—top, side and end view  
24  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
         
5.0  
About FIPS  
The Federal Information Processing Standard (FIPS) Publication 140-2, FIPS PUB 140-2, is a U.S. govern-  
ment computer security standard used to accredit cryptographic modules. It is titled “Security Requirements for  
Cryptographic Modules”. The initial publication was on May 25, 2001 and was last updated December 3, 2002.  
Purpose  
The National Institute of Standards and Technology (NIST) issued the FIPS 140 Publication Series to coordi-  
nate the requirements and standards for cryptography modules that include both hardware and software com-  
ponents.  
Federal Information Processing Standard (FIPS) 140-2 Level 2 Certification requires drives to go through gov-  
ernment agencies certifications to add requirements for physical tamper-evidence and role-based authentica-  
tion.  
Level 2 security  
Level 2 improves upon the physical security mechanisms of a Level 1 (lowest level of security) cryptographic  
module by requiring features that show evidence of tampering, including tamper-evident coatings or seals that  
must be broken to attain physical access to the plaintext cryptographic keys and critical security parameters  
(CSPs) within the module, or pick-resistant locks on covers or doors to protect against unauthorized physical  
access.  
Figure 6. Example of FIPS tamper evidence labels.  
Note. Does not represent actual drive.  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
25  
           
6.0  
About self-encrypting drives  
Self-encrypting drives (SEDs) offer encryption and security services for the protection of stored data, com-  
monly known as “protection of data at rest.” These drives are compliant with the Trusted Computing Group  
(TCG) Enterprise Storage Specifications as detailed in Section 3.17.  
The Trusted Computing Group (TCG) is an organization sponsored and operated by companies in the com-  
puter, storage and digital communications industry. Seagate’s SED models comply with the standards pub-  
lished by the TCG.  
To use the security features in the drive, the host must be capable of constructing and issuing the following two  
commands:  
• Security Protocol Out  
• Security Protocol In  
These commands are used to convey the TCG protocol to and from the drive in their command payloads.  
6.1  
Data encryption  
Encrypting drives use one inline encryption engine for each port, employing AES-128 data encryption in Cipher  
Block Chaining (CBC) mode to encrypt all data prior to being written on the media and to decrypt all data as it  
is read from the media. The encryption engines are always in operation, cannot be disabled, and do not detract  
in any way from the performance of the drive.  
The 32-byte Data Encryption Key (DEK) is a random number which is generated by the drive, never leaves the  
drive, and is inaccessible to the host system. The DEK is itself encrypted when it is stored on the media and  
when it is in volatile temporary storage (DRAM) external to the encryption engine. A unique data encryption  
key is used for each of the drive's possible16 data bands (see Section 6.5).  
6.2  
Controlled access  
The drive has two security partitions (SPs) called the "Admin SP" and the "Locking SP." These act as gate-  
keepers to the drive security services. Security-related commands will not be accepted unless they also supply  
the correct credentials to prove the requester is authorized to perform the command.  
6.2.1  
Admin SP  
The Admin SP allows the drive's owner to enable or disable firmware download operations (see Section 6.4).  
Access to the Admin SP is available using the SID (Secure ID) password or the MSID (Makers Secure ID)  
password.  
26  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
                                                     
6.2.2  
Locking SP  
The Locking SP controls read/write access to the media and the cryptographic erase feature. Access to the  
Locking SP is available using the BandMasterX or EraseMaster passwords. Since the drive owner can define  
up to 16 data bands on the drive, each data band has its own password called BandMasterX where X is the  
number of the data band (0 through 15).  
6.2.3  
Default password  
When the drive is shipped from the factory, all passwords are set to the value of MSID. This 32-byte random  
value is printed on the drive label and it can be read by the host electronically over the I/O. After receipt of the  
drive, it is the responsibility of the owner to use the default MSID password as the authority to change all other  
passwords to unique owner-specified values.  
6.3  
Random number generator (RNG)  
The drive has a 32-byte hardware RNG that it is uses to derive encryption keys or, if requested to do so, to pro-  
vide random numbers to the host for system use, including using these numbers as Authentication Keys (pass-  
words) for the drive’s Admin and Locking SPs.  
6.4  
Drive locking  
In addition to changing the passwords, as described in Section 6.2.3, the owner should also set the data  
access controls for the individual bands.  
The variable "LockOnReset" should be set to "PowerCycle" to ensure that the data bands will be locked if  
power is lost. This scenario occurs if the drive is removed from its cabinet. The drive will not honor any data  
read or write requests until the bands have been unlocked. This prevents the user data from being accessed  
without the appropriate credentials when the drive has been removed from its cabinet and installed in another  
system.  
When the drive is shipped from the factory, the firmware download port is unlocked.  
6.5  
Data bands  
When shipped from the factory, the drive is configured with a single data band called Band 0 (also known as  
the Global Data Band) which comprises LBA 0 through LBA max. The host may allocate Band1 by specifying a  
start LBA and an LBA range. The real estate for this band is taken from the Global Band. An additional 14 Data  
Bands may be defined in a similar way (Band2 through Band15) but before these bands can be allocated LBA  
space, they must first be individually enabled using the EraseMaster password.  
Data bands cannot overlap but they can be sequential with one band ending at LBA (x) and the next beginning  
at LBA (x+1).  
Each data band has its own drive-generated encryption key and its own user-supplied password. The host may  
change the Encryption Key (see Section 6.6) or the password when required. The bands should be aligned to  
4K LBA boundaries.  
6.6  
Cryptographic erase  
A significant feature of SEDs is the ability to perform a cryptographic erase. This involves the host telling the  
drive to change the data encryption key for a particular band. Once changed, the data is no longer recoverable  
since it was written with one key and will be read using a different key. Since the drive overwrites the old key  
with the new one, and keeps no history of key changes, the user data can never be recovered. This is tanta-  
mount to an instantaneous data erase and is very useful if the drive is to be scrapped or redispositioned.  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
27  
                                               
6.7  
Authenticated firmware download  
In addition to providing a locking mechanism to prevent unwanted firmware download attempts, the drive also  
only accepts download files which have been cryptographically signed by the appropriate Seagate Design  
Center.  
Three conditions must be met before the drive will allow the download operation:  
1. The download must be an SED file. A standard (base) drive (non-SED) file will be rejected.  
2. The download file must be signed and authenticated.  
3. As with a non-SED drive, the download file must pass the acceptance criteria for the drive. For example it  
must be applicable to the correct drive model, and have compatible revision and customer status.  
6.8  
Power requirements  
The standard drive models and the SED drive models have identical hardware, however the security and  
encryption portion of the drive controller ASIC is enabled and functional in the SED models. This represents a  
small additional drain on the 5V supply of about 30mA and a commensurate increase of about 150mW in  
power consumption. There is no additional drain on the 12V supply. See the tables in Section 3.8 for power  
requirements on the standard (non-SED) drive models.  
6.9  
Supported commands  
The SED models support the following two commands in addition to the commands supported by the standard  
(non-SED) models as listed in Table 6:  
• Security Protocol Out (B5h)  
• Security Protocol In (A2h)  
6.10  
RevertSP  
The SED models will support RevertSP feature where it erases all data in all bands on the device and returns  
the contents of all SPs (Security Providers) on the device to their Original Factory State.  
6.11  
ATA Security Erase Unit Command on SED SATA drives  
The ATA SECURITY ERASE UNIT command shall support both the Normal and Enhanced erase modes with  
the following modifications/additions:  
• Normal Erase: Normal erase shall be accomplished by changing the media encryption key for the drive fol-  
lowed by an overwrite operation that repeatedly writes a single sector containing random data to the entire  
drive. The write operation shall bypass the media encryption. On reading back the overwritten sectors, the  
host will receive a decrypted version, using the new encryption key, of the random data sector (the returned  
data will not match what was written).  
Enhanced Erase: Enhanced erase shall be accomplished by changing the media encryption key for the drive.  
6.12  
Sanitize Feature Set on SED Drives  
The drive shall support the Sanitize Feature Set as defined in ANSI/INCITS ACS-2 with the exceptions and/or  
modifications described in this section.  
The drive shall not support the OVERWRITE EXT and BLOCK ERASE EXT sub-commands.  
Support of the SANITIZE FREEZE LOCK EXT command shall be determined on a customer-specific basis.  
OEM drives shall support the command.  
28  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
             
7.0  
Serial ATA (SATA) interface  
These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA  
programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.  
For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT  
Attachment” specification.  
7.1  
Hot-Plug compatibility  
Constellation ES.2 Serial ATA drives incorporate connectors which enable you to hot plug these drives in  
accordance with the Serial ATA Revision 2.6 specification. This specification can be downloaded from  
Caution:  
The drive motor must come to a complete stop (Ready to spindle stop time indicated in Section 3.7)  
prior to changing the plane of operation. This time is required to insure data integrity.  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
29  
         
7.2  
Serial ATA device plug connector pin definitions  
Table 5 summarizes the signals on the Serial ATA interface and power connectors.  
Table 5: Serial ATA connector pin definitions  
Segment Pin  
Function  
Ground  
A+  
Definition  
S1  
S2  
S3  
S4  
S5  
S6  
2nd mate  
Differential signal pair A from Phy  
A-  
Ground  
B-  
2nd mate  
Differential signal pair B from Phy  
B+  
Signal  
S7  
Ground  
2nd mate  
Key and spacing separate signal and power segments  
P1  
V33  
3.3V power  
P2  
V33  
3.3V power  
P3  
V33  
3.3V power, pre-charge, 2nd mate  
1st mate  
P4  
Ground  
Ground  
Ground  
V5  
P5  
2nd mate  
P6  
2nd mate  
P7  
5V power, pre-charge, 2nd mate  
5V power  
P8  
V5  
Power  
P9  
V5  
5V power  
P10  
P11  
P12  
P13  
P14  
P15  
Ground  
2nd mate  
Ground or LED signal If grounded, drive does not use deferred spin  
Ground  
V12  
1st mate.  
12V power, pre-charge, 2nd mate  
12V power  
V12  
V12  
12V power  
Notes:  
1. All pins are in a single row, with a 1.27mm (0.050”) pitch.  
2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this  
case, the mating sequences are:  
• the ground pins P4 and P12.  
• the pre-charge power pins and the other ground pins.  
• the signal pins and the rest of the power pins.  
3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when  
installed in a blind-mate backplane configuration.  
4. All used voltage pins (Vx) must be terminated.  
30  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
 
7.3  
Supported ATA commands  
The following table lists Serial ATA standard commands that the drive supports. For a detailed description of  
the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See  
“S.M.A.R.T. commands” on page 38.for details and subcommands used in the S.M.A.R.T. implementation.  
Table 6:  
Supported ATA commands  
Command name  
Command code (in hex)  
E5  
Check Power Mode  
H
Device Configuration Freeze Lock  
Device Configuration Identify  
Device Configuration Restore  
Device Configuration Set  
Device Reset  
B1 / C1  
H
H
H
H
H
B1 / C2  
H
B1 / C0  
H
B1 / C3  
H
08  
92  
90  
H
H
H
Download Microcode  
Execute Device Diagnostics  
Flush Cache  
E7  
H
Flush Cache Extended  
Format Track  
EA  
H
50  
H
Identify Device  
EC  
H
Idle  
E3  
E1  
H
Idle Immediate  
H
H
Initialize Device Parameters  
Read Buffer  
91  
E4  
H
Read DMA  
C8  
H
Read DMA Extended  
Read DMA Without Retries  
Read Log Ext  
25  
H
C9  
H
H
2F  
Read Multiple  
C4  
H
Read Multiple Extended  
Read Native Max Address  
Read Native Max Address Extended  
Read Sectors  
29  
H
F8  
H
H
H
H
H
H
H
H
H
27  
20  
24  
21  
40  
42  
41  
10  
Read Sectors Extended  
Read Sectors Without Retries  
Read Verify Sectors  
Read Verify Sectors Extended  
Read Verify Sectors Without Retries  
Recalibrate  
Sanitize Device - Status Ext  
Sanitize Device - Crypto Scramble Ext  
Sanitize Device - Freeze Lock Ext  
Security Disable Password  
B4 / 0000  
H
H
B4 / 0011  
H
H
B4 / 0020  
H
H
F6  
H
Constellation ES.2 Serial ATA Product Manual, Rev. D  
31  
                                                                         
Command name  
Security Erase Prepare  
Security Erase Unit  
Security Freeze  
Security Set Password  
Security Unlock  
Seek  
Command code (in hex)  
F3  
F4  
F5  
F1  
F2  
H
H
H
H
H
H
70  
Set Features  
EF  
H
H
Set Max Address  
F9  
Note: Individual Set Max Address  
commands are identified by the value  
placed in the Set Max Features regis-  
ter as defined to the right.  
Address:  
Password:  
Lock:  
00  
01  
02  
03  
04  
H
H
H
H
H
Unlock:  
Freeze Lock:  
Set Max Address Extended  
Set Multiple Mode  
37  
H
C6  
H
Sleep  
E6  
H
S.M.A.R.T. Disable Operations  
S.M.A.R.T. Enable/Disable Autosave  
S.M.A.R.T. Enable Operations  
S.M.A.R.T. Execute Offline  
S.M.A.R.T. Read Attribute Thresholds  
S.M.A.R.T. Read Data  
S.M.A.R.T. Read Log Sector  
S.M.A.R.T. Return Status  
S.M.A.R.T. Save Attribute Values  
S.M.A.R.T. Write Log Sector  
Standby  
B0 / D9  
H
H
H
H
H
H
H
H
B0 / D2  
H
B0 / D8  
H
B0 / D4  
H
B0 / D1  
H
B0 / D0  
H
B0 / D5  
H
B0 / DA  
H
H
H
H
B0 / D3  
H
B0 / D6  
H
E2  
E0  
E8  
H
H
H
Standby Immediate  
Write Buffer  
Write DMA  
CA  
H
Write DMA Extended  
Write DMA FUA Extended  
Write DMA Without Retries  
Write Log Extended  
35  
H
3D  
CB  
H
H
3F  
H
Write Multiple  
C5  
39  
H
Write Multiple Extended  
Write Multiple FUA Extended  
Write Sectors  
H
CE  
H
30  
31  
34  
45  
H
Write Sectors Without Retries  
Write Sectors Extended  
Write Uncorrectable  
H
H
H
32  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
                                                                       
7.3.1  
Identify Device command  
The Identify Device command (command code EC ) transfers information about the drive to the host following  
H
power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 6 on  
page 31. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or  
vary with the state of the drive. See Section 3.0 on page 4 for default parameter settings.  
The following commands contain drive-specific features that may not be included in the Serial ATA  
specification.  
Word  
Description  
Value  
Configuration information:  
• Bit 15: 0 = ATA; 1 = ATAPI  
• Bit 7: removable media  
• Bit 6: removable controller  
• Bit 0: reserved  
0
0C5A  
H
1
Number of logical cylinders  
16,383  
2
ATA-reserved  
0000  
16  
H
3
Number of logical heads  
4
Retired  
0000  
0000  
H
H
5
Retired  
6
Number of logical sectors per logical track: 63  
Retired  
003F  
H
H
7–9  
10–19  
20  
21  
22  
0000  
Serial number: (20 ASCII characters, 0000 = none)  
ASCII  
H
Retired  
Retired  
Obsolete  
0000  
0400  
0000  
H
H
H
Firmware revision  
23–26  
27–46  
47  
x.xx  
(8 ASCII character string, padded with blanks to end of string)  
Drive model number:  
(40 ASCII characters, padded with blanks to end of string)  
(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write  
multiple (16)  
8010  
0000  
H
H
48  
Reserved  
49  
Standard Standby timer, IORDY supported and may be disabled  
ATA-reserved  
2F00  
H
H
H
H
H
50  
0000  
0200  
0200  
0007  
51  
PIO data-transfer cycle timing mode  
Retired  
52  
53  
Words 54–58, 64–70 and 88 are valid  
Number of current logical cylinders  
Number of current logical heads  
Number of current logical sectors per logical track  
Current capacity in sectors  
54  
xxxx  
xxxx  
xxxx  
xxxx  
H
55  
H
H
H
56  
57–58  
Number of sectors transferred during a Read Multiple  
or Write Multiple command  
59  
xxxx  
H
Constellation ES.2 Serial ATA Product Manual, Rev. D  
33  
   
Word  
Description  
Value  
Total number of user-addressable LBA sectors available  
(see Section 3.2 for related information)  
*Note: The maximum value allowed in this field is: 0FFFFFFFh  
(268,435,455 sectors, 137GB). Drives with capacities over 137GB will  
have 0FFFFFFFh in this field and the actual number of user-address-  
able LBAs specified in words 100-103. This is required for drives that  
support the 48-bit addressing feature.  
60–61  
0FFFFFFFh*  
62  
63  
Retired  
0000  
H
Multiword DMA active and modes supported  
(see note following this table)  
xx07  
H
64  
65  
Advanced PIO modes supported (modes 3 and 4 supported)  
Minimum multiword DMA transfer cycle time per word (120 ns)  
0003  
0078  
H
H
Recommended multiword DMA transfer cycle time per word  
(120 ns)  
66  
0078  
H
67  
Minimum PIO cycle time without IORDY flow control (240 ns)  
Minimum PIO cycle time with IORDY flow control (120 ns)  
ATA-reserved  
00F0  
H
H
H
68  
0078  
0000  
69–74  
75  
Queue depth  
001F  
H
76  
Serial ATA capabilities  
xxxx  
xxxx  
xxxx  
xxxx  
H
77  
Reserved for future Serial ATA definition  
Serial ATA features supported  
Serial ATA features enabled  
Major version number  
H
H
H
78  
79  
80  
003E  
H
81  
Minor version number  
0028  
H
82  
Command sets supported  
364B  
H
83  
Command sets supported  
7C03  
H
4003 See Word 108-111 note.  
(4003H = 0100000000000011  
binary)  
H
Command sets support extension  
(see note following this table)  
84  
85  
Command sets enabled  
30xx  
H
86  
Command sets enabled  
0001  
4000  
H
H
H
87  
Command sets enable extension  
Ultra DMA support and current mode (see note following this table)  
Security erase time  
88  
xx3F  
89  
0000  
0000  
H
H
90  
Enhanced security erase time  
Master password revision code  
Hardware reset value  
92  
FFFE  
H
93  
xxxx  
H
95–99  
ATA-reserved  
0000  
H
Total number of user-addressable LBA sectors available (see Section  
3.2 for related information). These words are required for drives that  
support the 48-bit addressing feature. Maximum value:  
0000FFFFFFFFFFFFh.  
ST33000650NS = 5,860,533,168  
ST33000651NS = 5,860,533,168  
ST33000652NS = 5,860,533,168  
100–103  
104–107  
ATA-reserved  
0000  
H
34  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
Word  
Description  
Value  
108–111  
The mandatory value of the world wide name (WWN) for the drive.  
NOTE: This field is valid if word 84, bit 8 is set to 1 indicating 64-bit  
WWN support.  
Each drive will have a unique  
value.  
112–127  
128  
ATA-reserved  
Security status  
Seagate-reserved  
ATA-reserved  
Integrity word  
0000  
0001  
H
H
129–159  
160–254  
255  
xxxx  
H
0000  
xxA5  
H
H
Note. See the bit descriptions below for words 63, 84, and 88 of the Identify Drive data.  
Description (if bit is set to 1)  
Bit  
0
Word 63  
Multiword DMA mode 0 is supported.  
Multiword DMA mode 1 is supported.  
Multiword DMA mode 2 is supported.  
Multiword DMA mode 0 is currently active.  
Multiword DMA mode 1 is currently active.  
Multiword DMA mode 2 is currently active.  
Word 84  
1
2
8
9
10  
Bit  
0
SMART error logging is supported.  
SMART self-test is supported.  
1
2
Media serial number is supported.  
Media Card Pass Through Command feature set is supported.  
Streaming feature set is supported.  
GPL feature set is supported.  
3
4
5
6
WRITE DMA FUA EXT and WRITE MULTIPLE FUA EXT commands are supported.  
7
WRITE DMA QUEUED FUA EXT command is supported.  
64-bit World Wide Name is supported.  
Obsolete.  
8
9-10  
11-12  
13  
14  
15  
Reserved for TLC.  
IDLE IMMEDIATE command with IUNLOAD feature is supported.  
Shall be set to 1.  
Shall be cleared to 0.  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
35  
Bit  
0
Word 88  
Ultra DMA mode 0 is supported.  
Ultra DMA mode 1 is supported.  
Ultra DMA mode 2 is supported.  
Ultra DMA mode 3 is supported.  
Ultra DMA mode 4 is supported.  
Ultra DMA mode 5 is supported.  
Ultra DMA mode 6 is supported.  
Ultra DMA mode 0 is currently active.  
Ultra DMA mode 1 is currently active.  
Ultra DMA mode 2 is currently active.  
Ultra DMA mode 3 is currently active.  
Ultra DMA mode 4 is currently active.  
Ultra DMA mode 5 is currently active.  
Ultra DMA mode 6 is currently active.  
1
2
3
4
5
6
8
9
10  
11  
12  
13  
14  
36  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
7.3.2  
Set Features command  
This command controls the implementation of various features that the drive supports. When the drive receives  
this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-  
rupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.  
Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the  
Features register are defined as follows:  
Table 7:  
Set Features command values  
02  
03  
Enable write cache (default).  
H
H
Set transfer mode (based on value in Sector Count register).  
Sector Count register values:  
00 Set PIO mode to default (PIO mode 2).  
H
01 Set PIO mode to default and disable IORDY (PIO mode 2).  
H
08 PIO mode 0  
H
09 PIO mode 1  
H
0A PIO mode 2  
H
0B PIO mode 3  
H
0C PIO mode 4 (default)  
H
20 Multiword DMA mode 0  
H
21 Multiword DMA mode 1  
H
22 Multiword DMA mode 2  
H
40 Ultra DMA mode 0  
H
41 Ultra DMA mode 1  
H
42 Ultra DMA mode 2  
H
43 Ultra DMA mode 3  
H
44 Ultra DMA mode 4  
H
45 Ultra DMA mode 5  
H
46 Ultra DMA mode 6  
H
10  
55  
82  
90  
Enable use of SATA features  
H
H
H
H
Disable read look-ahead (read cache) feature.  
Disable write cache  
Disable use of SATA features  
AA  
Enable read look-ahead (read cache) feature (default).  
Report full capacity available  
H
F1  
H
Note. At power-on, or after a hardware or software reset, the default values of the features are as indi-  
cated above.  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
37  
 
7.3.3  
S.M.A.R.T. commands  
S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-  
tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines  
that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.  
S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.  
commands and implementation, see the Draft ATA-5 Standard.  
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 ) that elimi-  
H
nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:  
This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that  
supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the  
drive uses.  
Table 8:  
S.M.A.R.T. commands  
Code in features register  
S.M.A.R.T. command  
D0  
D2  
D3  
D4  
D5  
D6  
D8  
D9  
S.M.A.R.T. Read Data  
H
H
H
H
H
H
H
H
S.M.A.R.T. Enable/Disable Attribute Autosave  
S.M.A.R.T. Save Attribute Values  
S.M.A.R.T. Execute Off-line Immediate (runs DST)  
S.M.A.R.T. Read Log Sector  
S.M.A.R.T. Write Log Sector  
S.M.A.R.T. Enable Operations  
S.M.A.R.T. Disable Operations  
S.M.A.R.T. Return Status  
DA  
H
Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04  
(abort) is written to the Error register.  
38  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
 
data bands 26  
Index  
Data encryption 26  
Data Encryption Key 26  
data-transfer rates 2  
DC power 8  
A
ACA 19  
acoustics 17  
Active 12  
Active mode 12  
actuator arm 8  
Admin SP 26  
decrypt 26  
Default logical geometry 6  
default MSID password 27  
DEK 26  
density 6  
Device Configuration Freeze Lock 31  
Device Configuration Identify 31  
Device Configuration Restore 31  
Device Configuration Set 31  
Device Reset 31  
dimensions 24  
disc surface 8  
Download Microcode 31  
Drive Locking 27  
drive mounting 24  
AES-128 data encryption 26  
Agency certification 18  
altitude 16  
ambient 15  
ambient temperature 7, 8  
Annualized Failure Rate (AFR) 18  
areal density 2, 6  
ATA commands 31  
Australia/New Zealand Standard AS/NZ CISPR22 19  
Australian Communication Authority (ACA) 19  
Australian C-Tick 19  
average idle current 9  
Average latency 7  
E
Electrical fast transient 17  
Electromagnetic compatibility 18  
Electromagnetic Compatibility (EMC) 19  
Electromagnetic Compatibility control Regulation 19  
Electromagnetic Compatibility Directive (2004/108/  
EC) 18  
Average seek time 7  
B
Band 0 27  
BandMasterX 27  
BPI 6  
Electromagnetic immunity 17  
Electrostatic discharge 17  
electrostatic discharge (ESD) 22  
EN 55022, Class B 18  
EN 55024 18  
EN60950 18  
enclosures 19  
encryption engine 26  
encryption key 27  
environmental  
buffer 7  
C
cables and connectors 23  
cache 7  
capacity 6  
CBC 26  
CE mark 18  
certification 18  
limits 15  
Check Power Mode 31  
China RoHS directive 20  
Cipher Block Chaining 26  
compatibility 18  
EraseMaster 27  
error-correction algorithms 2  
errors 18  
ESD 22  
Conducted noise 11  
Conducted RF immunity 17  
Configuring the drive 22  
connectors 23  
EU RoHS directive 20  
European Union (EU) requirements 18  
Execute Device Diagnostics 31  
Corrosive environment 20  
Cryptographic erase 27  
CSA60950-1 18  
F
FCC verification 19  
features 2  
Cylinders 6  
Federal Information Processing Standard 25  
FIPS 25  
firmware download port 27  
D
Data Bands 27  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
39  
Flush Cache 31  
Flush Cache Extended 31  
Format Track 31  
maximum start current 9  
mounting 23  
mounting configuration 24  
mounting screws 16  
mounting the drive 22  
MSID 26, 27  
Formatted capacity 6  
G
geometry 6  
Global Data Band 27  
gradient 15  
N
National Institute of Standards and Technology 25  
NIST 25  
guaranteed sectors 6  
noise 11  
nominal power 7  
non-operating  
H
Handling precautions 22  
heads 6  
humidity 16  
temperature 15  
Nonoperating shock 16  
Nonoperating vibration 16  
Nonrecoverable read errors 18  
humidity limits 15  
I
O
I/O data-transfer rate 6  
Identify Device 31  
Identify Device command 33  
Idle 12, 31  
Idle Immediate 31  
Operating power 8  
Operating shock 16  
Operating vibration 16  
P
Idle mode 8, 12  
Information Technology Equipment (ITE) 18  
Initialize Device Parameters 31  
Input noise ripple 11  
input voltage 8  
password 26, 27  
passwords 27  
PDT 17  
peak operating current 9  
Physical characteristics 7  
point-to-point 3, 23  
Power consumption 8  
power consumption 8  
Power modes 12  
interface 6, 29  
interference 19  
internal data-transfer rate OD 6  
is 7  
ISO document 7779 17  
ITE 18  
Power specifications 8  
PowerCycle 27  
Power-management modes 12  
Power-on to Ready 7  
precautions 22  
printed circuit board 22  
programmable power management 12  
Prominent Discrete Tones 17  
protection of data at rest 26  
K
KCC 19  
Korean Communications Commission 19  
Korean RRL 19  
L
latency 7  
latency time 8  
LBA mode 6  
Locking SP 26, 27  
LockOnReset 27  
logical geometry 6  
Q
quick reference 4  
R
Radiated RF immunity 17  
radio and television interference 19  
radio frequency (RF) 17  
Random number generator 27  
random seeks 8  
M
maintenance 18  
Makers Secure ID 26  
master/slave 3  
Read Buffer 31  
40  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
Read DMA 31  
Security Freeze 32  
security partitions 26  
Security Protocol In 26  
Security Protocol Out 26  
Security Set Password 32  
Security Unlock 32  
Seek 32  
seek mode 8  
Seek mode power 8  
Seek time 7  
Read DMA Extended 31  
Read DMA without Retries 31  
read errors 18  
Read Log Ext 31  
Read Multiple 31  
Read Multiple Extended 31  
Read Native Max Address 31  
Read Native Max Address Extended 31  
Read Sectors 31  
Read Sectors Extended 31  
Read Sectors Without Retries 31  
Read Verify Sectors 31  
Read Verify Sectors Extended 31  
Read Verify Sectors Without Retries 31  
read/write actuator arm 8  
Read/write heads 6  
Read/write power 8  
Recalibrate 31  
recording density 6  
recording method 6  
Recording technology 6  
reference  
self-encrypting drives 26  
Serial ATA (SATA) interface 29  
serial ATA ports 3  
Servo electronics 8  
servo electronics 8  
Set Features 32  
Set Max Address 32  
Set Max Address Extended 32  
Set Multiple Mode 32  
shipping container 15  
Shock 16  
SID 26  
single-track seeks 7  
Sleep 12, 32  
Sleep mode 12  
documents 21  
relative humidity 16  
Reliability 18  
sound 17  
RMS read/write current 11  
RNG 27  
Specification summary table 4  
spindle speed 6  
Spinup power 8  
RoHS 20  
RRL 19  
Standby 12, 32  
Standby Immediate 32  
Standby mode 8, 12  
standby timer 12  
S
Standby to Ready 7  
Start/stop times 7  
static-discharge 22  
subassembly 19  
support services 1  
Surge immunity 17  
S.M.A.R.T. Disable Operations 32  
S.M.A.R.T. Enable Operations 32  
S.M.A.R.T. Enable/Disable Autosave 32  
S.M.A.R.T. Execute Offline 32  
S.M.A.R.T. implementation 31  
S.M.A.R.T. Read Attribute Thresholds 32  
S.M.A.R.T. Read Data 32  
S.M.A.R.T. Read Log Sector 32  
S.M.A.R.T. Return Status 32  
S.M.A.R.T. Save Attribute Values 32  
S.M.A.R.T. Write Log sector 32  
Safety certification 18  
T
TCG 26  
technical support services 1  
temperature 7, 15  
limits 15  
Sanitize Device 31  
sanitize feature set 28  
SATA 29  
non-operating 15  
Test for Prominent Discrete Tones 17  
timer 12  
screws 16  
timers 12  
sectors 6  
track density 6  
Sectors per track 6  
Track-to-track 7  
Secure ID 26  
Track-to-track seek time 7  
Trusted Computing Group 26  
Security Disable Password 31  
Security Erase Prepare 32  
Security Erase Unit 32  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
41  
U
UL60950-1 18  
V
Vibration 16  
voltage 8  
Voltage dips, interrupts 17  
Voltage tolerance 11  
W
weight 7  
wet bulb temperature 16  
Write Buffer 32  
Write DMA 32  
Write DMA Extended 32  
Write DMA FUA Extended 32  
Write DMA Without Retries 32  
Write Log Extended 32  
Write Multiple 32  
Write Multiple Extended 32  
Write Multiple FUA Extended 32  
Write Sectors 32  
Write Sectors Extended 32  
Write Sectors Without Retries 32  
Write Uncorrectable 32  
42  
Constellation ES.2 Serial ATA Product Manual, Rev. D  
Seagate Technology LLC  
920 Disc Drive, Scotts Valley, California 95066-4544, USA  
Publication Number: 100633157, Rev. D  

Yamaha CDC 697 User Manual
Transcend Information TS16GSSD25S M User Manual
Toshiba SD R2612 User Manual
Teac CD Player CD RW890 User Manual
Sony DREAM MACHINE ICF CD815 User Manual
Seagate ST66022FX User Manual
Seagate MOMENTUS 72003 SATA ST9250421ASG User Manual
Samsung GT i8000L User Manual
Samsung GH68 06704A User Manual
Oregon RM382P User Manual