Seagate BARRACUDA ST3160215AS User Manual

Product Manual  
Barracuda 7200.10 Serial ATA  
ST3750640AS  
ST3750840AS  
ST3500630AS  
ST3500830AS  
ST3400620AS  
ST3400820AS  
ST3320620AS  
ST3320820AS  
ST3300620AS  
ST3300820AS  
ST3250620AS  
ST3250820AS  
ST3250410AS  
ST3250310AS  
ST3200820AS  
ST3160815AS  
ST3160310AS  
ST3160215AS  
ST3120815AS  
ST3120215AS  
ST380815AS  
ST380215AS  
ST340815AS  
ST340215AS  
100402371  
Rev. K  
December 2007  
Contents  
5.0  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
i
ii  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
1.0  
Introduction  
This manual describes the functional, mechanical and interface specifications for the following Seagate  
Barracuda® 7200.10 Serial ATA model drives:  
ST3750640AS  
ST3750840AS  
ST3500630AS  
ST3500830AS  
ST3400620AS  
ST3400820AS  
ST3320620AS  
ST3320820AS  
ST3300620AS  
ST3300820AS  
ST3250620AS  
ST3250820AS  
ST3250410AS  
ST3250310AS  
ST3200820AS  
ST3160815AS  
ST3160310AS  
ST3160215AS  
ST3120815AS  
ST3120215AS  
ST380815AS  
ST380215AS  
ST340815AS  
ST340215AS  
These drives provide the following key features:  
• 7,200 RPM spindle speed.  
• High instantaneous (burst) data-transfer rates (up to 300 Mbytes per second).  
• Perpendicular recording and Tunneling Magnetoresistive (TMR) recording heads for increased areal density.  
• State-of-the-art cache and on-the-fly error-correction algorithms.  
• Native Command Queueing with command ordering to increase performance in demanding applications.  
• Full-track multiple-sector transfer capability without local processor intervention.  
• Quiet operation.  
• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.  
• Support for S.M.A.R.T. drive monitoring and reporting.  
• Supports latching SATA cables and connectors.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
1
         
1.1  
About the Serial ATA interface  
The Serial ATA interface provides several advantages over the traditional (parallel) ATA interface. The primary  
advantages include:  
• Easy installation and configuration with true plug-and-play connectivity. It is not necessary to set any jump-  
ers or other configuration options.  
• Thinner and more flexible cabling for improved enclosure airflow and ease of installation.  
• Scalability to higher performance levels.  
In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial  
ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current  
system and expect all of your existing applications to work as normal.  
The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host  
adapter. There is no master/slave relationship with Serial ATA devices like there is with parallel ATA. If two  
drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they  
were both “masters” on two separate ports. This essentially means both drives behave as if they are Device 0  
(master) devices.  
Note. The host adapter may, optionally, emulate a master/slave environment to host software where two  
devices on separate Serial ATA ports are represented to host software as a Device 0 (master) and  
Device 1 (slave) accessed at the same set of host bus addresses. A host adapter that emulates a  
master/slave environment manages two sets of shadow registers. This is not a typical Serial ATA  
environment.  
The Serial ATA host adapter and drive share the function of emulating parallel ATA device behavior to provide  
backward compatibility with existing host systems and software. The Command and Control Block registers,  
PIO and DMA data transfers, resets, and interrupts are all emulated.  
The Serial ATA host adapter contains a set of registers that shadow the contents of the traditional device regis-  
ters, referred to as the Shadow Register Block. All Serial ATA devices behave like Device 0 devices. For addi-  
tional information about how Serial ATA emulates parallel ATA, refer to the “Serial ATA: High Speed Serialized  
2
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
       
2.0  
Drive specifications  
Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal  
power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the  
following drive models:  
ST3750640AS  
ST3750840AS  
ST3500630AS  
ST3500830AS  
ST3400620AS  
ST3400820AS  
ST3320620AS  
ST3320820AS  
ST3300620AS  
ST3300820AS  
ST3250620AS  
ST3250820AS  
ST3250410AS  
ST3250310AS  
ST3200820AS  
ST3160815AS  
ST3160310AS  
ST3160215AS  
ST3120815AS  
ST3120215AS  
ST380815AS  
ST380215AS  
ST340815AS  
ST340215AS  
2.1  
Specification summary tables  
The specifications listed in the following tables are for quick reference. For details on specification measure-  
ment or definition, see the appropriate section of this manual.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
3
       
Table 1:  
Drive specifications summary for 750 Gbyte models  
Drive specification  
ST3750640AS  
750 Gbytes  
1,465,149,168  
8
ST3750840AS  
Formatted capacitty (512 bytes/sector)*  
Guaranteed sectors  
Heads  
Discs  
4
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
769 kbits/in avg  
141 ktracks/in avg  
109 Gbits/in2 avg  
7,200 RPM  
1,030 Mbits/sec max  
78 Mbytes/sec max  
300 Mbytes/sec max  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
16 Mbytes  
8 Mbytes  
Height (max)  
26.1 mm (1.028 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
720 grams (1.59 lbs)  
4.16 msec  
Width (max)  
Length (max)  
Weight (typical)  
Average latency  
Power-on to ready  
Standby to ready  
15 sec max  
15 sec max  
Track-to-track seek time  
Average seek, read  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
<0.8 msec typical read; <1.0 msec typical write  
<8.5 msec typical  
<10.0 msec typical  
2.8 amps  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient  
Relative humidity  
0° to 60°C (operating)  
–40° to 70°C (nonoperating)  
20°C per hour max (operating)  
30°C per hour max (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature  
30% per hour max  
37.7°C max (operating)  
37.7°C max (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
68 Gs at 2 msec max  
300 Gs at 2 msec max  
Non-Operational Shock  
4
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
Vibration, operating  
ST3750640AS  
ST3750840AS  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.50 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle**  
2.8 bels (typical)  
3.0 bels (max)  
Performance seek  
3.7 bels (typical)  
3.9 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser to  
access the following web page: www.seagate.com/support/service/  
From this page, click on the “Verify Your Warranty” link. You will be asked  
to provide the drive serial number, model number (or part number) and  
country of purchase. The system will display the warranty information for  
your drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the Serial ATA Revision  
2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
5
Table 2:  
Drive specifications summary for 500 Gbyte models  
Drive specification  
ST3500630AS  
500 Gbytes  
976,773,168  
6
ST3500830AS  
Formatted capacity (512 bytes/sector)*  
Guaranteed sectors  
Heads  
Discs  
3
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
769 kbits/in avg  
141 ktracks/in avg  
109 Gbits/in2 avg  
7,200 RPM  
1,030 Mbits/sec max  
72 Mbytes/sec max  
300 Mbytes/sec max  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
16 Mbytes  
8 Mbytes  
Height (max)  
26.1 mm (1.028 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
635 grams (1.40 lbs)  
4.16 msec  
Width (max)  
Length (max)  
Weight (typical)  
Average latency  
Power-on to ready  
Standby to ready  
15 sec max  
15 sec max  
Track-to-track seek time  
Average seek, read  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
<0.8 msec typical read; <1.0 msec typical write  
<8.5 msec typical  
<10.0 msec typical  
2.8 amps  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient (max)  
Relative humidity  
0° to 60°C (operating)  
–40° to 70°C (nonoperating)  
20°C per hour (operating)  
30°C per hour (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature (max)  
30% per hour max  
37.7 °C (operating)  
37.7 °C (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
68 Gs max at 2 msec  
300 Gs max at 2 msec  
Non-Operational Shock  
6
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
Vibration, operating  
ST3500630AS  
ST3500830AS  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.50 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle**  
2.8 bels (typical)  
3.0 bels (max)  
Performance seek  
3.7 bels (typical)  
3.9 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser to access  
the following web page: www.seagate.com/support/service/  
From this page, click on the “Verify Your Warranty” link. You will be asked to  
provide the drive serial number, model number (or part number) and country  
of purchase. The system will display the warranty information for your drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the Serial ATA Revi-  
sion 2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
7
Table 3:  
Drive specifications summary for 400 Gbyte models  
Drive specification  
ST3400620AS  
400 Gbytes  
781,422,768  
5
ST3400820AS  
Formatted capacity (512 bytes/sector)*  
Guaranteed sectors  
Heads  
Doscs  
3
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
769 kbits/in avg  
141 ktracks/in avg  
109 Gbits/in2 avg  
7,200 RPM  
1,030 Mbits/sec max  
72 Mbytes/sec max  
300 Mbytes/sec max  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
16 Mbytes  
8 Mbytes  
Height (max)  
26.1 mm (1.028 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
635 grams (1.40 lbs)  
4.16 msec  
Width (max)  
Length (max)  
Weight (typical)  
Average latency  
Power-on to ready  
Standby to ready  
15 sec max  
15 sec max  
Track-to-track seek time  
Average seek, read  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
<0.8 msec typical read; <1.0 msec typical write  
<8.5 msec typical  
<10.0 msec typical  
2.8 amps  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient  
Relative humidity  
0° to 60°C (operating)  
–40° to 70°C (nonoperating)  
20°C per hour max (operating)  
30°C per hour max (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature  
30% per hour max  
37.7 °C max (operating)  
37.7 °C max (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
68 Gs max at 2 msec  
300 Gs max at 2 msec  
Non-Operational Shock  
8
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
Vibration, operating  
ST3400620AS  
ST3400820AS  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.50 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle**  
2.7 bels (typical)  
2.9 bels (max)  
Performance seek  
3.4 bels (typical)  
3.6 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser to  
access the following web page: www.seagate.com/support/service/  
From this page, click on the “Verify Your Warranty” link. You will be asked  
to provide the drive serial number, model number (or part number) and  
country of purchase. The system will display the warranty information for  
your drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the Serial ATA Revision  
2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
9
Table 4:  
Drive specifications summary for 320 Gbyte models  
Drive specification  
ST3320620AS  
320 Gbytes  
625,142,448  
4
ST3320820AS  
Formatted capacity (512 bytes/sector)*  
Guaranteed sectors  
Heads  
Discs  
2
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
769 kbits/in avg  
141 ktracks/in avg  
109 Gbits/in2 avg  
7,200 RPM  
1,030 Mbits/sec max  
72 Mbytes/sec max  
300 Mbytes/sec max  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
16 Mbytes  
8 Mbytes  
Height (max)  
26.1 mm (1.028 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
635 grams (1.40 lbs)  
4.16 msec  
Width (max)  
Length (max)  
Weight (typical)  
Average latency  
Power-on to ready  
Standby to ready  
15 sec max  
15 sec max  
Track-to-track seek time  
Average seek, read  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
<0.8 msec typical read; <1.0 typical write  
<8.5 msec typical  
<10.0 msec typical  
2.8 amps  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient  
Relative humidity  
0° to 60°C (operating)  
–40° to 70°C (nonoperating)  
20°C per hour max (operating)  
30°C per hour max (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature  
30% per hour max  
37.7°C max (operating)  
37.7°C max (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
68 Gs max at 2 msec  
350 Gs max at 2 msec  
Non-Operational Shock  
10  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
Vibration, operating  
ST3320620AS  
ST3320820AS  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.50 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle**  
2.5 bels (typical)  
2.9 bels (max)  
Performance seek  
3.0 bels (typical)  
3.2 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser to  
access the following web page: www.seagate.com/support/service/  
From this page, click on the “Verify Your Warranty” link. You will be  
asked to provide the drive serial number, model number (or part num-  
ber) and country of purchase. The system will display the warranty  
information for your drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the Serial ATA Revision 2.5  
specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
11  
Table 5:  
Drive specifications summary for 300 Gbyte models  
Drive specification  
ST3300620AS  
300 Gbytes  
586,072,368  
3
ST3300820AS  
Formatted capacity (512 bytes/sector)*  
Guaranteed sectors  
Heads  
Discs  
2
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
769 kbits/in avg  
141 ktracks/in avg  
109 Gbits/in2 avg  
7,200 RPM  
1,030 Mbits/sec max  
72 Mbytes/sec max  
300 Mbytes/sec max  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
16 Mbytes  
8 Mbytes  
Height (max)  
26.1 mm (1.028 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
600 grams (1.32 lb.)  
4.16 msec  
Width (max)  
Length (max)  
Weight (typical  
Average latency  
Power-on to ready  
Standby to ready  
11 sec max  
11 sec max  
Track-to-track seek time  
Average seek, read  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
<0.8 msec typical read; <1.0 msec typical write  
<8.5 msec typical  
<10.0 msec typical  
2.8 amps  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient  
Relative humidity  
0° to 60°C (operating)  
–40° to 70°C (nonoperating)  
20°C per hour max (operating)  
30°C per hour max (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature  
30% per hour max  
37.7°C max (operating)  
37.7°C max (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
68 Gs max at 2 msec  
350 Gs max at 2 msec  
Non-Operational Shock  
12  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
Vibration, operating  
ST3300620AS  
ST3300820AS  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.50 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle**  
2.5 bels (typical)  
2.9 bels (max)  
Performance seek  
3.0 bels (typical)  
3.2 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser to  
access the following web page: www.seagate.com/support/service/  
From this page, click on the “Verify Your Warranty” link. You will be  
asked to provide the drive serial number, model number (or part num-  
ber) and country of purchase. The system will display the warranty infor-  
mation for your drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the Serial ATA Revision  
2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
13  
Table 6:  
Drive specifications summary for 250 Gbyte models  
Drive specification  
ST3250620AS  
ST3250820AS  
ST3250410AS  
ST3250310AS  
Formatted capacity (512 bytes/sector)*  
Guaranteed sectors  
Heads  
250 Gbytes  
488,397,168  
3
2
1
Discs  
2
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
769 kbits/in avg  
141 ktracks/in avg  
109 Gbits/in2 avg  
7,200 RPM  
1,030 Mbits/sec max  
72 Mbytes/sec max  
300 Mbytes/sec max  
PIO modes 0–4  
1,049 kbits/in avg  
155 ktracks/in avg  
163 Gbits/in2 avg  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
1,212 Mbits/sec max  
106 Mbytes/sec max  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
16 Mbytes  
8 Mbytes  
16 Mbytes  
8 Mbytes  
Height (max)  
26.1 mm (1.028 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
600 grams (1.32 lb.)  
4.16 msec  
19.99 mm (.787 inches)  
Width (max)  
Length (max)  
Weight (typical)  
Average latency  
Power-on to ready  
Standby to ready  
Track-to-track seek time  
380 grams (0.838lb.)  
11 sec max  
7.9 sec max  
7.9 sec max  
11 sec max  
<0.8 msec typical read,  
<1.0 msec typical write  
<0.8 msec typical read,  
<1.0 msec typical write  
Average seek, read  
<8.5 msec typical  
<10.0 msec typical  
2.8 amps  
<11.0 msec typical  
<12.0 msec typical  
2.0 amps  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient  
Relative humidity  
0° to 60°C per hour max (operating)  
–40° to 70°C per hour max (nonoperating)  
20°C (operating)  
30°C (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature  
30% per hour max  
37.7°C max (operating)  
37.7°C max (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
68 Gs max at 2 msec  
350 Gs max at 2 msec  
63 Gs max at 2 msec  
Non-Operational Shock  
14  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
ST3250620AS  
ST3250820AS  
ST3250410AS  
ST3250310AS  
Vibration, operating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.50 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle**  
2.5 bels (typical)  
2.9 bels (max)  
2.6 bels (typical)  
2.7 bels (max)  
Performance seek  
Quiet seek  
3.0 bels (typical)  
3.2 bels (max)  
2.7 bels (typical)  
2.8 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser to access the following  
From this page, click on the “Verify Your Warranty” link. You will be asked to provide the  
drive serial number, model number (or part number) and country of purchase. The system  
will display the warranty information for your drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the  
Serial ATA Revision 2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
15  
Table 7:  
Drive specifications summary for the 200 Gbyte mode  
Drive specification  
ST3200820AS  
200 Gbytes  
390,721,968  
3
Formatted capacity (512 bytes/sector)*  
Guaranteed sectors  
Heads  
Discs  
2
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
769 kbits/in avg  
141 ktracks/in avg  
109 Gbits/in2 avg  
7,200 RPM  
1,030 Mbits/sec max  
72 Mbytes/sec max  
300 Mbytes/sec max  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
8 Mbytes  
Height (max)  
26.1 mm (1.028 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
600 grams (1.32 lb.)  
4.16 msec  
Width (max)  
Length (max)  
Weight (typical)  
Average latency  
Power-on to ready  
Standby to ready  
11 sec max  
11 sec max  
Track-to-track seek time  
Average seek, read  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
<0.8 msec typical read; <1.0 msec typical write  
<8.5 msec typical  
<10.0 msec typical  
2.8 amps  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient  
Relative humidity  
0° to 60°C (operating)  
–40° to 70°C (nonoperating)  
20°C per hour max (operating)  
30°C per hour max (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature  
30% per hour max  
37.7°C max (operating)  
37.7°C max (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
68 Gs max at 2 msec  
350 Gs max at 2 msec  
Non-Operational Shock  
16  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
Vibration, operating  
ST3200820AS  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.5 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle**  
2.5 bels (typical)  
2.9 bels (max)  
Performance seek  
3.0 bels (typical)  
3.2 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser  
to access the following web page:  
From this page, click on the “Verify Your Warranty” link. You will  
be asked to provide the drive serial number, model number (or  
part number) and country of purchase. The system will display  
the warranty information for your drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the Serial ATA Revision 2.5 spec-  
ification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
17  
Table 8:  
Drive specifications summary for the 160 Gbyte models  
Drive specification  
ST3160815AS  
ST3160310AS  
ST3160215AS  
Formatted capacity (512 bytes/sector)*  
Guaranteed sectors  
Heads  
160 Gbytes  
312,581,808  
2
Discs  
1
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
732 kbits/in avg  
137.259 ktracks/in avg  
101 Gbits/in2 avg  
7,200 RPM  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
930 Mbits/sec max  
78 Mbytes/sec max **  
300 Mbytes/sec max  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
8 Mbytes  
2 Mbytes  
Height (max)  
19.99 mm (0.787 inches)  
101.6 mm (4.010 inches)  
146.99 mm (5.787 inches)  
380 grams (0.838 lb.)  
4.16 msec  
Width (max)  
Length (max)  
Weight (typical)  
Average latency  
Power-on to ready  
Standby to ready  
7.9 sec max  
7.9 sec max  
Track-to-track seek time  
Average seek, read  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
<0.8 msec typical read; <1.0 msec typical write  
<11 msec typical  
<12 msec typical  
<2.0 amps  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient  
Relative humidity  
0° to 60°C (operating)  
–40° to 75°C (nonoperating)  
20°C per hour max (operating)  
30°C per hour max (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature  
30% per hour max  
37.7°C max (operating)  
40°C max (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
63 Gs max at 2 msec  
350 Gs max at 2 msec  
Non-Operational Shock  
18  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
Vibration, operating  
ST3160815AS  
ST3160310AS  
ST3160215AS  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.5 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle***  
2.8 bels (typical)  
3.0 bels (max)  
Quiet seek  
3.0 bels (typical)  
3.2 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web  
browser to access the following web page:  
From this page, click on the “Verify Your Warranty” link.  
You will be asked to provide the drive serial number,  
model number (or part number) and country of purchase.  
The system will display the warranty information for your  
drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the Serial ATA Revision 2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
** 7200.10 family product achieved higher sustained data rate over same 7200.9 family capacity points using identical measurement  
methodology.  
*** During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
19  
Table 9:  
Drive specifications summary for the 120 Gbyte models  
Drive specification  
ST3120815AS  
120 Gbytes  
234,441,648  
2
ST3120215AS  
Formatted capacity (512 bytes/sector)*  
Guaranteed sectors  
Heads  
Discs  
1
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
732 kbits/in avg  
137.259 ktracks/in avg  
101 Gbits/in2 avg  
7,200 RPM  
930 Mbits/sec max  
78 Mbytes/sec max **  
300 Mbytes/sec max  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
8 Mbytes  
2 Mbytes  
Height (max)  
19.99 mm (0.787 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
380 grams (0.838 lb.)  
4.16 msec  
Width (max)  
Length (max)  
Weight (typical)  
Average latency  
Power-on to ready  
Standby to ready  
7.9 sec max  
7.9 sec max  
Track-to-track seek time  
Average seek, read  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
<0.8 msec typical read; <1.0 msec typical write  
<11 msec typical  
<12 msec typical  
<2.0 amps  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient  
Relative humidity  
0° to 60°C (operating)  
–40° to 75°C (nonoperating)  
20°C per hour max (operating)  
30°C per hour max (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature  
30% per hour max  
37.7°C max (operating)  
40°C max (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
63 Gs max at 2 msec  
350 Gs max at 2 msec  
Non-Operational Shock  
20  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
Vibration, operating  
ST3120815AS  
ST3120215AS  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.5 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle***  
2.8 bels (typical)  
3.0 bels (max)  
Quiet seek  
3.0 bels (typical)  
3.2 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web  
browser to access the following web page:  
From this page, click on the “Verify Your Warranty” link.  
You will be asked to provide the drive serial number,  
model number (or part number) and country of purchase.  
The system will display the warranty information for your  
drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the Serial ATA Revision 2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
** 7200.10 family product achieved higher sustained data rate over same 7200.9 family capacity points using identical measurement  
methodology.  
*** During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
21  
Table 10: Drive specifications summary for the 80 Gbyte models  
Drive specification  
ST380815AS  
80 Gbytes  
ST380215AS  
Formatted capacity (512 bytes/sector)*  
Guaranteed sectors  
Heads  
156,301,488  
1
Discs  
1
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
732 kbits/in avg  
137.259 ktracks/in avg  
101 Gbits/in2 avg  
7,200 RPM  
930 Mbits/sec max  
78 Mbytes/sec max **  
300 Mbytes/sec max  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
8 Mbytes  
2 Mbytes  
Height (max)  
19.99 mm (0.787 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
365 grams (0.805 lb.)  
4.16 msec  
Width (max)  
Length (max)  
Weight (typical)  
Average latency  
Power-on to read  
7.9 sec max  
Standby to ready  
7.9 sec max  
Track-to-track seek time  
Average seek, read  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
<0.8 msec typical read); <1.0 msec typical write  
<11 msec typical  
<12 msec typical  
<2.0 amps  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient  
Relative humidity  
0° to 60°C (operating)  
–40° to 75°C (nonoperating)  
20°C per hour max (operating)  
30°C per hour max (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature  
30% per hour max  
37.7°C max (operating)  
40°C max (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
63 Gs max at 2 msec  
350 Gs max at 2 msec  
Non-Operational Shock  
22  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
Vibration, operating  
ST380815AS  
ST380215AS  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.5 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle***  
2.8 bels (typical)  
3.0 bels (max)  
Quiet seek  
3.0 bels (typical)  
3.2 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web  
browser to access the following web page:  
From this page, click on the “Verify Your Warranty” link.  
You will be asked to provide the drive serial number,  
model number (or part number) and country of purchase.  
The system will display the warranty information for your  
drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the Serial ATA Revision 2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
** 7200.10 family product achieved higher sustained data rate over same 7200.9 family capacity points using identical measurement  
methodology.  
*** During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
23  
Table 11:  
Drive specifications summary for the 40 Gbyte models  
Drive specification  
ST340815AS  
ST340215AS  
Formatted capacity (512 bytes/sector)*  
Guaranteed sectors  
Heads  
40 Gbytes  
78,165,360  
1
Discs  
1
Bytes per sector  
512  
Default sectors per track  
Default read/write heads  
Default cylinders  
63  
16  
16,383  
Recording density  
732 kbits/in avg  
137.259 ktracks/in avg  
101 Gbits/in2 avg  
7,200 RPM  
Track density  
Areal density  
Spindle speed  
Internal data transfer rate  
Sustained data transfer rate OD (read)  
I/O data-transfer rate  
ATA data-transfer modes supported  
930 Mbits/sec max  
78 Mbytes/sec max **  
300 Mbytes/sec max  
PIO modes 0–4  
Multiword DMA modes 0–2  
Ultra DMA modes 0–6  
Cache buffer  
8 Mbytes  
2 Mbytes  
Height (max)  
19.99 mm (0.787 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
365 grams (0.805 lb.)  
4.16 msec  
Width (max)  
Length (max)  
Weight (typical)  
Average latency  
Power-on to ready  
Standby to ready  
7.9 sec max  
7.9 sec max  
Track-to-track seek time  
Average seek, read  
Average seek, write  
Startup current (typical) 12V (peak)  
Voltage tolerance (including noise)  
<0.8 msec typical read; <1.0 msec typical write  
<11 msec typical  
<12 msec typical  
<2.0 amps  
5V ± 5%  
12V ± 10%  
Ambient temperature  
Temperature gradient  
Relative humidity  
0° to 60°C (operating)  
–40° to 75°C (nonoperating)  
20°C per hour max (operating)  
30°C per hour max (nonoperating)  
5% to 90% (operating)  
5% to 95% (nonoperating)  
Relative humidity gradient  
Wet bulb temperature  
30% per hour max  
37.7°C max (operating)  
40°C max (nonoperating)  
Altitude, operating  
–60.96 m to 3,048 m  
(–200 ft. to 10,000+ ft.)  
Altitude, nonoperating  
(below mean sea level, max)  
–60.96 m to 12,192 m  
(–200 ft. to 40,000+ ft.)  
Operational Shock  
63 Gs max at 2 msec  
350 Gs max at 2 msec  
Non-Operational Shock  
24  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Drive specification  
Vibration, operating  
ST340815AS  
ST340215AS  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 0.5 Gs  
350–500 Hz:: 0.25 Gs  
Vibration, nonoperating  
5–22 Hz: 0.25 Gs, Limited displacement  
22–350 Hz: 5.0 Gs  
350–500 Hz:: 1.0 Gs  
Drive acoustics, sound power  
Idle***  
2.8 bels (typical)  
3.0 bels (max)  
Quiet seek  
3.0 bels (typical)  
3.2 bels (max)  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Warranty  
1 per 1014 bits read  
0.34%  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web  
browser to access the following web page:  
From this page, click on the “Verify Your Warranty” link.  
You will be asked to provide the drive serial number,  
model number (or part number) and country of purchase.  
The system will display the warranty information for your  
drive.  
Contact start-stop cycles  
50,000 at 25°C, 50% rel. humidity  
Yes  
Supports Hotplug operation per the Serial ATA Revision 2.5 specification  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
** 7200.10 family product achieved higher sustained data rate over same 7200.9 family capacity points using identical measurement  
methodology.  
*** During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
25  
2.2  
Formatted capacity  
Formatted  
capacity*  
Guaranteed  
sectors  
Model  
Bytes per sector  
ST3750640AS  
ST3750840AS  
750 Gbytes  
500 Gbytes  
400 Gbytes  
320 Gbytes  
300 Gbytes  
1,465,149,168  
976,773,168  
781,422,768  
625,142,448  
586,072,368  
512  
512  
512  
512  
512  
ST3500630AS  
ST3500830AS  
ST3400620AS  
ST3400820AS  
ST3320620AS  
ST3320820AS  
ST3300620AS  
ST3300820AS  
ST3250620AS  
ST3250820AS  
ST3250410AS  
ST3250310AS  
250 Gbytes  
488,397,168  
512  
ST3200820AS  
200 Gbytes  
160 Gbytes  
390,721,968  
312,581,808  
512  
512  
ST3160815AS  
ST3160310AS  
ST3160215AS  
ST3120815AS  
ST3120215AS  
120 Gbytes  
80 Gbytes  
40 Gbytes  
234,441,648  
156,301,488  
78,165,360  
512  
512  
512  
ST380815AS  
ST380215AS  
ST340815AS  
ST340215AS  
*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment  
and formatting.  
2.2.1  
LBA mode  
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,  
where n is the number of guaranteed sectors as defined above.  
See Section 4.3.1, "Identify Device command" (words 60-61 and 100-103) for additional information about 48-  
bit addressing support of drives with capacities over 137 Gbytes.  
2.3  
Default logical geometry  
Cylinders  
Read/write heads  
Sectors per track  
63  
16,383  
16  
LBA mode  
When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1,  
where n is the number of guaranteed sectors as defined above.  
26  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
                             
2.4  
Recording and interface technology  
Model capacity  
750 500  
400  
320  
300  
Interface  
Serial ATA (SATA)  
Perpendicular  
769  
Recording method  
Recording density (kbits/inch avg)  
Track density (ktracks/inch avg)  
Areal density (Gbits/inch2 avg)  
141  
109  
Spindle speed (RPM)  
7,200 ± 0.2%  
1,030  
Internal data transfer rate (Mbits/sec max)  
Sustained data transfer rate (read) (Mbytes/sec max)  
I/O data-transfer rate (Mbytes/sec max)  
78  
72  
300  
Model capacity  
160  
120  
80  
40  
Interface  
Serial ATA (SATA)  
Recording method  
Perpendicular  
732  
Recording density (kbits/inch avg)  
Track density (ktracks/inch avg)  
Areal density (Gbits/inch2 avg)  
Spindle speed (RPM)  
137.259  
101  
7,200 ± 0.2%  
930  
Internal data transfer rate (Mbits/sec max)  
Sustained data transfer rate (read) (Mbytes/sec max)  
I/O data-transfer rate (Mbytes/sec max)  
78 *  
300  
* 7200.10 family product achieved higher sustained data rate over same 7200.9 family capacity points using identical measurement  
methodology.  
Model capacity  
ST3250620AS, ST3250820AS  
and ST3200820AS  
ST3250410AS and  
ST3250310AS  
Interface  
Serial ATA (SATA)  
Recording method  
Perpendicular  
Recording density (kbits/inch avg)  
Track density (ktracks/inch avg)  
Areal density (Gbits/inch2 avg)  
Spindle speed (RPM)  
769  
1,049  
155  
141  
109  
163  
7,200 ± 0.2%  
Internal data transfer rate (Mbits/sec max)  
Sustained data transfer rate (read) (Mbytes/sec max)  
I/O data-transfer rate (Mbytes/sec max)  
1,030  
72  
1,212  
106  
300  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
27  
                     
2.5  
Physical characteristics  
Maximum height (4, 3 and 2 disc models)  
Maximum height (1 disc models)  
Maximum width  
26.1 mm (1.028 inches)  
19.99 mm (0.787 inches)  
101.85 mm (4.010 inches)  
146.99 mm (5.787 inches)  
Maximum length  
Typical weight  
ST3750640AS and ST3750840AS  
720 grams (1.59 lbs)  
635 grams (1.40 lbs)  
ST3500630AS, ST3500830AS, ST3400620AS, ST3400820AS,  
ST3320620AS and ST3320820AS  
ST3300620AS, ST3300820AS, ST3250620AS, ST3250820AS  
and ST3250410AS  
600 grams (1.32 lbs)  
ST3250310AS, ST3200820AS, ST3160815AS, ST3160310AS,  
ST3160215AS, ST3120815AS and ST3120215AS,  
380 grams (0.838 lbs.)  
365 grams (0.805 lbs)  
ST380815AS, ST380215AS, ST340815AS and ST340215AS  
Cache buffer  
ST3750640AS, ST3500630AS, ST3400620AS, ST3320620AS,  
ST3300620AS, ST3250620AS and ST3250410AS  
16 Mbytes (16,384 kbytes)  
ST3750840AS, ST3500830AS, ST3400820AS, ST3320820AS,  
ST3300820AS, ST3250820AS, ST3250310AS, ST3200820AS,  
ST3160815AS, ST3160310AS, ST3120815AS, ST380815AS  
and ST340815AS  
8 Mbytes (8,192 kbytes)  
2 Mbytes (2,048 kbytes)  
ST3160215AS, ST3120215AS, ST380215AS and ST340215AS  
28  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
               
2.6  
Seek time  
Seek measurements are taken with nominal power at 25°C ambient temperature. All times are measured using  
drive diagnostics. The specifications in the table below are defined as follows:  
• Track-to-track seek time is an average of all possible single-track seeks in both directions.  
• Average seek time is a true statistical random average of at least 5,000 measurements of seeks between  
random tracks, less overhead.  
ST3250410AS and ST3250310AS*  
and 160 - 40 GB models**  
750 - 300 GB models*, ST3250620AS,  
ST3250820AS and 200 GB model  
Typical seek times (msec)  
Track-to-track  
Read  
<0.8  
<8.5  
4.16  
Write  
<1.0  
Read  
<0.8  
Write  
<1.0  
Average  
<10.0  
<11.0  
<12.0  
Average latency:  
*Measured in performance mode.  
**Measured in quiet mode.  
Note. These drives are designed to consistently meet the seek times represented in this manual. Physical  
seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted  
values. However, due to the manner in which these drives are formatted, benchmark tests that  
include command overhead or measure logical seeks may produce results that vary from these  
specifications.  
2.7  
Start/stop times  
750 - 320 GB  
models  
300 GB model  
ST3250620AS, ST3250820AS  
and 200 GB model  
ST3250410AS, ST3250310AS  
and 160 - 40 GB models  
Power-on to Ready (sec)  
15 (max)  
15 (max)  
10 (max)  
11 (max)  
11 (max)  
7.9 (max)  
7.9 (max)  
Standby to Ready (sec)  
Ready to spindle stop (sec)  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
29  
                               
2.8  
Power specifications  
The drive receives DC power (+5V or +12V) through a native SATA power connector. See Figure 4 on page 42.  
2.8.1 Power consumption  
Power requirements for the drives are listed in the table on page 9. Typical power measurements are based on  
an average of drives tested, under nominal conditions, using 5.0V and 12.0V input voltage at 25°C ambient  
temperature.  
• Spinup power  
Spinup power is measured from the time of power-on to the time that the drive spindle reaches operating  
speed.  
• Seek mode  
During seek mode, the read/write actuator arm moves toward a specific position on the disc surface and  
does not execute a read or write operation. Servo electronics are active. Seek mode power represents the  
worst-case power consumption, using only random seeks with read or write latency time. This mode is not  
typical and is provided for worst-case information.  
• Read/write power and current  
Read/write power is measured with the heads on track, based on a 16-sector write followed by a 32-msec  
delay, then a 16-sector read followed by a 32-msec delay.  
• Operating power and current  
Operating power is measured using 40 percent random seeks, 40 percent read/write mode (1 write for each  
10 reads) and 20 percent drive idle mode.  
• Idle mode power  
Idle mode power is measured with the drive up to speed, with servo electronics active and with the heads in  
a random track location.  
• Standby mode  
During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/  
write electronics are in power-down mode.  
Table 12:  
DC power requirements  
Power dissipation (4-disc values shown)  
Avg (watts 25° C)  
Avg 5V typ amps  
Avg 12V typ amps  
2.8 (peak)  
0.520  
Spinup  
Idle*  
9.30  
10.40  
13.00  
12.60  
0.80  
0.80  
0.611  
0.719  
0.772  
0.613  
0.106  
0.106  
Idle* (with offline activity)  
Operating (40% r/w, 40% seek, 20% inop.)  
Seeking (random, 20% idle)  
Standby  
0.567  
0.762  
0.795  
0.023  
Sleep  
0.023  
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
30  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
                                                           
2.8.1.1  
Typical current profiles  
Figure 1. Typical 5V startup and operation current profile  
Figure 2. Typical 12V startup and operation current profile  
2.8.2 Conducted noise  
Input noise ripple is measured at the host system power supply across an equivalent 80-ohm resistive load on  
the +12 volt line or an equivalent 15-ohm resistive load on the +5 volt line.  
• Using 12-volt power, the drive is expected to operate with a maximum of 120 mV peak-to-peak square-wave  
injected noise at up to 10 MHz.  
• Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave  
injected noise at up to 10 MHz.  
Note. Equivalent resistance is calculated by dividing the nominal voltage by the typical RMS read/write  
current.  
2.8.3  
Voltage tolerance  
Voltage tolerance (including noise):  
5V ± 5%  
12V ± 10%  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
31  
                 
2.8.4  
Power-management modes  
The drive provides programmable power management to provide greater energy efficiency. In most systems,  
you can control power management through the system setup program. The drive features the following  
power-management modes:  
Power modes  
Active  
Heads  
Spindle  
Rotating  
Rotating  
Stopped  
Stopped  
Buffer  
Tracking  
Tracking  
Parked  
Parked  
Enabled  
Enabled  
Enabled  
Disabled  
Idle  
Standby  
Sleep  
Active mode  
The drive is in Active mode during the read/write and seek operations.  
• Idle mode  
The buffer remains enabled, and the drive accepts all commands and returns to Active mode any time disc  
access is necessary.  
Standby mode  
The drive enters Standby mode when the host sends a Standby Immediate command. If the host has set  
the standby timer, the drive can also enter Standby mode automatically after the drive has been inactive for  
a specifiable length of time. The standby timer delay is established using a Standby or Idle command. In  
Standby mode, the drive buffer is enabled, the heads are parked and the spindle is at rest. The drive  
accepts all commands and returns to Active mode any time disc access is necessary.  
• Sleep mode  
The drive enters Sleep mode after receiving a Sleep command from the host. In Sleep mode, the drive  
buffer is disabled, the heads are parked and the spindle is at rest. The drive leaves Sleep mode after it  
receives a Hard Reset or Soft Reset from the host. After receiving a reset, the drive exits Sleep mode and  
enters Standby mode with all current translation parameters intact.  
• Idle and Standby timers  
Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and  
begins counting down from its specified delay times to zero. If the standby timer reaches zero before any  
drive activity is required, the drive makes a transition to Standby mode. In both Idle and Standby mode, the  
drive accepts all commands and returns to Active mode when disc access is necessary.  
32  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
                             
2.9  
Environmental specifications  
Ambient temperature  
2.9.1  
Ambient temperature is defined as the temperature of the environment immediately surrounding the drive.  
Actual drive case temperature should not exceed 69°C (156°F) within the operating ambient conditions.  
Above 1,000 feet (305 meters), the maximum temperature is derated linearly to 112°F (44°C) at 10,000 feet  
(3,048 meters).  
Operating:  
0° to 60°C (32° to 140°F)  
Nonoperating:  
–40° to 70°C (–40° to 158°F)  
2.9.2  
Temperature gradient  
Operating:  
20°C per hour (68°F per hour max), without condensation  
30°C per hour (86°F per hour max)  
Nonoperating:  
2.9.3  
2.9.3.1  
Humidity  
Relative humidity  
Operating:  
Nonoperating:  
5% to 90% noncondensing (30% per hour max)  
5% to 95% noncondensing (30% per hour max)  
2.9.3.2  
Wet bulb temperature  
Operating:  
37.7°C (99.9°F max)  
Nonoperating:  
200 - 750 GB models: 37.7°C (99.9°F max)  
40 - 160 GB models: 40°C (104°F max)  
2.9.4  
Altitude  
Operating:  
–60.96 m to 3,048 m (–200 ft. to 10,000+ ft.)  
–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)  
Nonoperating:  
2.9.5  
Shock  
All shock specifications assume that the drive is mounted securely with the input shock applied at the drive  
mounting screws. Shock may be applied in the X, Y or Z axis.  
2.9.5.1  
Operating shock  
These models (750GB, 500GB, 400GB, 320GB, 200GB, ST3250620AS and ST3250820AS) comply with the  
performance levels specified in this document when subjected to a maximum operating shock of 68 Gs based  
on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second.  
These models (ST3250410AS, ST3250310AS, 160GB, 120GB, 80GB and 40GB) comply with the  
performance levels specified in this document when subjected to a maximum operating shock of 63 Gs based  
on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
33  
                                       
2.9.5.2  
Nonoperating shock  
1 and 2 Disc models  
The nonoperating shock level that the drive can experience without incurring physical damage or degradation  
in performance when subsequently put into operation is 350 Gs based on a nonrepetitive half-sine shock pulse  
of 2 msec duration.  
3 and 4 Disc models  
The nonoperating shock level that the drive can experience without incurring physical damage or degradation  
in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse  
of 2 msec duration.  
2.9.6  
Vibration  
All vibration specifications assume that the drive is mounted securely with the input vibration applied at the  
drive mounting screws. Vibration may be applied in the X, Y or Z axis.  
2.9.6.1  
Operating vibration  
The maximum vibration levels that the drive may experience while meeting the performance standards speci-  
fied in this document are specified below.  
5–22 Hz  
0.25 Gs (Limited displacement)  
22–350 Hz  
350–500 Hz  
0.50 Gs  
0.25 Gs  
2.9.6.2  
Nonoperating vibration  
The maximum nonoperating vibration levels that the drive may experience without incurring physical damage  
or degradation in performance when subsequently put into operation are specified below.  
5–22 Hz  
0.25 Gs (limited displacement)  
22–350 Hz  
350–500 Hz  
5.0 Gs  
1.0 Gs  
34  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
             
2.10  
Acoustics  
Drive acoustics are measured as overall A-weighted acoustic sound power levels (no pure tones). All mea-  
surements are consistent with ISO document 7779. Sound power measurements are taken under essentially  
free-field conditions over a reflecting plane. For all tests, the drive is oriented with the cover facing upward.  
Note. For seek mode tests, the drive is placed in seek mode only. The number of seeks per second is defined  
by the following equation:  
(Number of seeks per second = 0.4 / (average latency + average access time)  
Table 13:  
Fluid Dynamic Bearing (FDB) motor acoustics  
Idle*  
Seek  
2.8 bels (typ)  
3.0 bels (max)  
3.7 bels (typ)**  
3.9 bels (max)**  
ST3750640AS, ST3750840AS, ST3500630AS, ST3500830AS  
ST3400620AS, ST3400820AS  
2.7 bels (typ)  
2.9 bels (max)  
3.4 bels (typ)**  
3.6 bels (max)**  
ST3320620AS, ST3320820AS, ST3300620AS, ST3300820AS, 2.5 bels (typ)  
3.0 bels (typ)**  
3.2 bels (max)**  
ST3250620AS, ST3250820AS, ST3200820AS  
2.9 bels (max)  
2.6 bels (typ)  
2.7 bels (max)  
2.7 bels (typ)***  
2.8 bels (max)***  
ST3250410AS, ST3250310AS  
ST3160815AS, ST3160310AS, ST3160215AS, ST3120815AS, 2.8 bels (typ)  
3.0 bels (typ)***  
3.2 bels (max)***  
ST3120215AS, ST380815AS, ST380215AS, ST340815AS,  
ST340215AS  
3.0 bels (max)  
*During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and  
power to operational levels.  
**Measured in performance mode.  
***Measured in quiet mode.  
2.10.1  
Test for Prominent Discrete Tones (PDTs)  
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this  
process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to  
discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone  
ratios according to Annex D of the ECMA-74 standards.  
* Defined as the median curve given by ISO 389-7 (Tf curve) minus 10dB at all frequencies.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
35  
         
2.11  
Electromagnetic immunity  
When properly installed in a representative host system, the drive operates without errors or degradation in  
performance when subjected to the radio frequency (RF) environments defined in the following table:  
Table 14:  
Test  
Radio frequency environments  
Description  
Performance level  
Reference standard  
Electrostatic  
discharge  
Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV  
B
EN 61000-4-2: 95  
Radiated RF  
immunity  
80 to 1,000 MHz, 3 V/m,  
A
B
EN 61000-4-3: 96  
ENV 50204: 95  
80% AM with 1 kHz sine  
900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz  
Electrical fast  
transient  
± 1 kV on AC mains, ± 0.5 kV on external I/O  
EN 61000-4-4: 95  
Surge immunity ± 1 kV differential, ± 2 kV common, AC mains  
B
A
EN 61000-4-5: 95  
EN 61000-4-6: 97  
Conducted RF  
immunity  
150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine  
Voltage dips,  
interrupts  
0% open, 5 seconds  
0% short, 5 seconds  
40%, 0.10 seconds  
70%, 0.01 seconds  
C
C
C
B
EN 61000-4-11: 94  
36  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
                   
2.12  
Reliability  
2.12.1  
Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)  
The product shall achieve an Annualized Failure Rate (AFR) of 0.34% (MTBF of 0.7 million hours) when oper-  
ated in an environment of ambient air temperatures of 25°C. Operation at temperatures outside the specifica-  
tions in Section 2.9 may increase the product AFR (decrease MTBF). AFR and MTBF are population statistics  
that are not relevant to individual units.  
AFR and MTBF specifications are based on the following assumptions for desktop personal computer environ-  
ments:  
• 2400 power-on-hours per year.  
• 10,000 average motor start/stop cycles per year.  
• Operations at nominal voltages.  
• Temperatures outside the specifications in Section 2.9 may reduce the product reliability.  
• Normal I/O duty cycle for desktop personal computers. Operation at excessive I/O duty cycle may degrade  
product reliability.  
The desktop personal computer environment of power-on-hours, temperature, and I/O duty cycle affect the  
product AFR and MTBF. The AFR and MTBF will be degraded if used in a enterprise application.  
14  
Nonrecoverable read errors  
Annualized Failure Rate (AFR)  
Contact start-stop cycles  
1 per 10 bits read, max  
0.34% (nominal power, 25°C ambient temperature)  
50,000 cycles  
(at nominal voltage and temperature, with 60 cycles per hour and a 50% duty cycle)  
Warranty  
5 years on distribution units.  
To determine the warranty for a specific drive, use a web browser to access the fol-  
From this page, click on the “Verify Your Warranty” link. You will be asked to provide  
the drive serial number, model number (or part number) and country of purchase.  
The system will display the warranty information for your drive.  
Preventive maintenance  
None required.  
2.13  
Agency certification  
2.13.1  
Safety certification  
The drives are recognized in accordance with UL 1950 and CSA C22.2 (950) and meet all applicable sections  
of IEC950 and EN 60950.  
2.13.2  
Electromagnetic compatibility  
Hard drives that display the CE mark comply with the European Union (EU) requirements specified in the Elec-  
tromagnetic Compatibility Directive (89/336/EEC). Testing is performed to the levels specified by the product  
standards for Information Technology Equipment (ITE). Emission levels are defined by EN 55022, Class B and  
the immunity levels are defined by EN 55024.  
Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the  
directives when used in the test systems, we cannot guarantee that all systems will comply with the directives.  
The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if  
necessary) and terminators on all unused I/O ports. Computer manufacturers and system integrators should  
confirm EMC compliance and provide CE marking for their products.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
37  
                                                                           
Korean RRL  
If these drives have the Korea Ministry of Information and Communication (MIC) logo, they comply with para-  
graph 1 of Article 11 of the Electromagnetic Compatibility control Regulation and meet the Electromagnetic  
Compatibility (EMC) Framework requirements of the Radio Research Laboratory (RRL) Ministry of Information  
and Communication Republic of Korea.  
These drives have been tested and comply with the Electromagnetic Interference/Electromagnetic Susceptibil-  
ity (EMI/EMS) for Class B products. Drives are tested in a representative, end-user system by a Korean-recog-  
nized lab.  
• Family name: Barracuda 7200.10  
• Certificate number: STX-L3510 (B)  
Australian C-Tick (N176)  
If these models have the C-Tick marking, they comply with the Australia/New Zealand Standard AS/NZS3548  
1995 and meet the Electromagnetic Compatibility (EMC) Framework requirements of the Australian Communi-  
cation Authority (ACA).  
2.13.3  
FCC verification  
These drives are intended to be contained solely within a personal computer or similar enclosure (not attached  
as an external device). As such, each drive is considered to be a subassembly even when it is individually mar-  
keted to the customer. As a subassembly, no Federal Communications Commission verification or certification  
of the device is required.  
Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure,  
disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursu-  
ant to Subpart J, Part 15 of the FCC rules. Operation with noncertified assemblies is likely to result in interfer-  
ence to radio and television reception.  
Radio and television interference. This equipment generates and uses radio frequency energy and if not  
installed and used in strict accordance with the manufacturer’s instructions, may cause interference to radio  
and television reception.  
This equipment is designed to provide reasonable protection against such interference in a residential installa-  
tion. However, there is no guarantee that interference will not occur in a particular installation. If this equipment  
does cause interference to radio or television, which can be determined by turning the equipment on and off,  
you are encouraged to try one or more of the following corrective measures:  
• Reorient the receiving antenna.  
• Move the device to one side or the other of the radio or TV.  
• Move the device farther away from the radio or TV.  
• Plug the computer into a different outlet so that the receiver and computer are on different branch outlets.  
If necessary, you should consult your dealer or an experienced radio/television technician for additional sug-  
gestions. You may find helpful the following booklet prepared by the Federal Communications Commission:  
How to Identify and Resolve Radio-Television Interference Problems. This booklet is available from the Super-  
intendent of Documents, U.S. Government Printing Office, Washington, DC 20402. Refer to publication num-  
ber 004-000-00345-4.  
38  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
                               
2.14  
Environmental protection  
Seagate designs its products to meet environmental protection requirements worldwide, including regulations  
restricting certain chemical substances.  
2.14.1  
European Union Restriction of Hazardous Substances (RoHS) Directive  
Seagate designs its products to meet environmental protection requirements worldwide, including regulations  
restricting certain chemical substances. A new law, the European Union Restriction of Hazardous Substances  
(RoHS) Directive, restricts the presence of chemical substances, including Lead, Cadmium, Mercury,  
Hexavalent Chromium, PBB and PBDE, in electronic products, effective July 2006. This drive is manufactured  
with components and materials that comply with the RoHS Directive.  
2.14.2  
2.14.2  
China Restriction of Hazardous Substances (RoHS) Directive  
中国限制危险物品的指令  
This product has an Environmental Protection Use Period (EPUP) of 20 years. The following  
table contains information mandated by China's "Marking Requirements for Control of Pollution  
Caused by Electronic Information Products" Standard.  
"O" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is lower  
than the threshold defined by the China RoHS MCV Standard.  
O"表示该部件(于同类物品程度上)所含的危险和有毒物质低于中国RoHS MCV标准所定义的门槛值。  
"X" indicates the hazardous and toxic substance content of the part (at the homogenous material level) is over  
the threshold defined by the China RoHS MCV Standard.  
X "表示该部件(于同类物品程度上)所含的危险和有毒物质超出中国RoHS MCV标准所定义的门槛值。  
2.15  
Corrosive environment  
Seagate electronic drive components pass accelerated corrosion testing equivalent to 10 years exposure to  
light industrial environments containing sulfurous gases, chlorine and nitric oxide, classes G and H per ASTM  
B845. However, this accelerated testing cannot duplicate every potential application environment. Users  
should use caution exposing any electronic components to uncontrolled chemical pollutants and corrosive  
chemicals as electronic drive component reliability can be affected by the installation environment. The silver,  
copper, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chlo-  
ride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components  
should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or  
exposed to an ambient relative humidity greater than 95%. Materials used in cabinet fabrication, such as vulca-  
nized rubber, that can outgas corrosive compounds should be minimized or eliminated. The useful life of any  
electronic equipment may be extended by replacing materials near circuitry with sulfide-free alternatives.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
39  
               
40  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
3.0  
Configuring and mounting the drive  
This section contains the specifications and instructions for configuring and mounting the drive.  
3.1  
Handling and static-discharge precautions  
After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic dis-  
charge (ESD) hazards. Observe the following standard handling and static-discharge precautions:  
Caution:  
• Before handling the drive, put on a grounded wrist strap, or ground yourself frequently by touching the metal  
chassis of a computer that is plugged into a grounded outlet. Wear a grounded wrist strap throughout the entire  
installation procedure.  
• Handle the drive by its edges or frame only.  
• The drive is extremely fragile—handle it with care. Do not press down on the drive top cover.  
• Always rest the drive on a padded, antistatic surface until you mount it in the computer.  
• Do not touch the connector pins or the printed circuit board.  
• Do not remove the factory-installed labels from the drive or cover them with additional labels. Removal voids  
the warranty. Some factory-installed labels contain information needed to service the drive. Other labels are  
used to seal out dirt and contamination.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
41  
                   
3.2  
Configuring the drive  
Each drive on the Serial ATA interface connects point-to-point with the Serial ATA host adapter. There is no  
master/slave relationship because each drive is considered a master in a point-to-point relationship. If two  
drives are attached on one Serial ATA host adapter, the host operating system views the two devices as if they  
were both “masters” on two separate ports. Both drives behave as if they are Device 0 (master) devices.  
Serial ATA drives are designed for easy installation. It is usually not necessary to set any jumpers on the drive  
for proper operation; however, if you connect the drive and receive a “drive not detected” error, your SATA-  
equipped motherboard or host adapter may use a chipset that does not support SATA speed autonegotiation. If  
you have a motherboard or host adapter that does not support autonegotiation:  
• Install a jumper as shown in Figure 3 below to limit the data transfer rate to 1.5 Gbits per second (and leave  
the drive connected to the SATA-equipped motherboard or host adapter that doesn’t support autonegotiation)  
or  
• Install a SATA host adapter that supports autonegotiation, leave the drive jumper block set to “Normal  
operation” (see Figure 3 below), and connect the drive to that adapter. This option has the benefit of not limiting  
the drive to a 1.5 Gbits/sec transfer rate.  
3.0 Gbits per second operation  
Limit data transfer rate to  
1.5 Gbits per second  
Jumper block  
SATA interface connector  
Figure 3. Serial ATA connectors  
SATA power connector  
3.3  
Serial ATA cables and connectors  
The Serial ATA interface cable consists of four conductors in two differential pairs, plus three ground connec-  
tions. The cable size may be 30 to 26 AWG with a maximum length of one meter (39.37 inches). See Table 15  
for connector pin definitions. Either end of the SATA signal cable can be attached to the drive or host.  
For direct backplane connection, the drive connectors are inserted directly into the host receptacle. The drive  
and the host receptacle incorporate features that enable the direct connection to be hot pluggable and blind  
mateable.  
For installations which require cables, you can connect the drive as illustrated in Figure 4.  
Signal connector  
Power connector  
Signal cable  
Power cable  
Figure 4. Attaching SATA cabling  
Each cable is keyed to ensure correct orientation. Barracuda 7200.10 Serial ATA drives support latching SATA  
connectors.  
42  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
             
3.4  
Drive mounting  
You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the  
bottom-mounting holes. See Figures 5 and 6 for drive mounting dimensions. Follow these important mounting  
precautions when mounting the drive:  
• Allow a minimum clearance of 0.030 inches (0.76 mm) around the entire perimeter of the drive for cooling.  
• Use only 6-32 UNC mounting screws.  
• The screws should be inserted no more than 0.150 inch (3.81 mm) into the bottom or side mounting holes.  
• Do not overtighten the mounting screws (maximum torque: 6 inch-lb).  
Recommended  
case temperature  
measurement location  
[1]  
5.787 (146.9898) max.  
.250 + .015  
(6.35 + .381)  
(3x both sides)  
1.638  
(41.605)  
1.122  
+ .020  
(28.499  
+ .508)  
[1]  
[1]  
4.000  
(101.60)  
[1]  
4.000  
(101.6)  
1.028 max  
(26.111 max)  
[1]  
.138  
(3.505)  
.814  
(20.676)  
C of conn. Datum B  
L
2.00  
Notes:  
(50.80)  
Dimensions are shown in inches (mm).  
[1] Dimensions per SFF-8301 specification  
C of drive  
L
[1]  
2 x 3.750  
(2 x 95.25)  
2 x 1.625  
(2 x 41.28)  
[1]  
[1]  
2 x 1.750  
(2 x 44.45)  
4.000  
(101.6)  
[1]  
Recommended  
case temperature  
measurement location  
Figure 5. Mounting dimensions for 750-200 GB models (except ST3250410AS and ST3250310AS)  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
43  
       
Figure 6. Mounting dimensions for 160-40 GB models (including ST3250410AS and ST3250310AS)  
44  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
   
4.0  
Serial ATA (SATA) interface  
These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA  
programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.  
For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT  
Attachment” specification.  
4.1  
Hot-Plug compatibility  
Barracuda 7200.10 Serial ATA drives incorporate connectors which enable you to hot plug these drives in  
accordance with the Serial ATA Revision 2.5 specification. This specification can be downloaded from  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
45  
         
4.2  
Serial ATA device plug connector pin definitions  
Table 15 summarizes the signals on the Serial ATA interface and power connectors..  
Table 15: Serial ATA connector pin definitions  
Segment Pin  
Function  
Ground  
A+  
Definition  
S1  
S2  
S3  
S4  
S5  
S6  
2nd mate  
Differential signal pair A from Phy  
A-  
Ground  
B-  
2nd mate  
Differential signal pair B from Phy  
B+  
Signal  
S7  
Ground  
2nd mate  
Key and spacing separate signal and power segments  
P1  
V33  
3.3V power  
P2  
V33  
3.3V power  
P3  
V33  
3.3V power, pre-charge, 2nd mate  
1st mate  
P4  
Ground  
Ground  
Ground  
V5  
P5  
2nd mate  
P6  
2nd mate  
P7  
5V power, pre-charge, 2nd mate  
5V power  
P8  
V5  
Power  
P9  
V5  
5V power  
P10  
P11  
P12  
P13  
P14  
P15  
Ground  
2nd mate  
Ground or LED signal If grounded, drive does not use deferred spin  
Ground  
V12  
1st mate.  
12V power, pre-charge, 2nd mate  
12V power  
V12  
V12  
12V power  
Notes:  
1. All pins are in a single row, with a 1.27 mm (0.050”) pitch.  
2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this  
case, the mating sequences are:  
• the ground pins P4 and P12.  
• the pre-charge power pins and the other ground pins.  
• the signal pins and the rest of the power pins.  
3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when  
installed in a blind-mate backplane configuration.  
4. All used voltage pins (Vx) must be terminated.  
46  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
   
4.3  
Supported ATA commands  
The following table lists Serial ATA standard commands that the drive supports. For a detailed description of  
the ATA commands, refer to the Serial ATA: High Speed Serialized AT Attachment specification. See  
“S.M.A.R.T. commands” on page 54.for details and subcommands used in the S.M.A.R.T. implementation.  
Table 16:  
Supported ATA commands  
Command name  
Command code (in hex)  
98 or E5  
Check Power Mode  
Device Configuration Freeze Lock  
Device Configuration Identify  
Device Configuration Restore  
Device Configuration Set  
Device Reset  
H
H
B1 / C1  
H
H
B1 / C2  
H
H
H
H
B1 / C0  
H
B1 / C3  
H
08  
92  
90  
H
H
H
Download Microcode  
Execute Device Diagnostics  
Flush Cache  
E7  
H
Flush Cache Extended  
Format Track  
EA  
H
50  
H
Identify Device  
EC  
H
Idle  
97 or E3  
H
H
Idle Immediate  
95 or E1  
H
H
Initialize Device Parameters  
Read Buffer  
91  
H
E4  
H
Read DMA  
C8  
H
Read DMA Extended  
Read DMA Without Retries  
Read Log Ext  
25  
H
C9  
H
H
2F  
Read Multiple  
C4  
H
Read Multiple Extended  
Read Native Max Address  
Read Native Max Address Extended  
Read Sectors  
29  
H
F8  
H
H
H
H
H
H
H
H
H
27  
20  
24  
21  
40  
42  
41  
10  
Read Sectors Extended  
Read Sectors Without Retries  
Read Verify Sectors  
Read Verify Sectors Extended  
Read Verify Sectors Without Retries  
Recalibrate  
Security Disable Password  
Security Erase Prepare  
F6  
F3  
H
H
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
47  
                                                                         
Command name  
Security Erase Unit  
Security Freeze  
Security Set Password  
Security Unlock  
Seek  
Command code (in hex)  
F4  
F5  
F1  
F2  
H
H
H
H
H
70  
Set Features  
EF  
H
Set Max Address  
F9  
H
Note: Individual Set Max Address  
commands are identified by the value  
placed in the Set Max Features regis-  
ter as defined to the right.  
Address:  
Password:  
Lock:  
00  
01  
02  
03  
04  
H
H
H
H
H
Unlock:  
Freeze Lock:  
Set Max Address Extended  
Set Multiple Mode  
37  
H
C6  
H
Sleep  
99 or E6  
H
H
S.M.A.R.T. Disable Operations  
S.M.A.R.T. Enable/Disable Autosave  
S.M.A.R.T. Enable Operations  
S.M.A.R.T. Execute Offline  
S.M.A.R.T. Read Attribute Thresholds  
S.M.A.R.T. Read Data  
S.M.A.R.T. Read Log Sector  
S.M.A.R.T. Return Status  
S.M.A.R.T. Save Attribute Values  
S.M.A.R.T. Write Log Sector  
Standby  
B0 / D9  
H
H
B0 / D2  
H
H
H
H
H
H
H
B0 / D8  
H
B0 / D4  
H
B0 / D1  
H
B0 / D0  
H
B0 / D5  
H
B0 / DA  
H
H
H
H
B0 / D3  
H
B0 / D6  
H
96 or E2  
H
H
H
Standby Immediate  
94 or E0  
H
Write Buffer  
E8  
H
Write DMA  
CA  
H
Write DMA Extended  
35  
H
Write DMA FUA Extended  
Write DMA Without Retries  
Write Log Extended  
CD  
H
H
CB  
3F  
H
Write Multiple  
C5  
H
Write Multiple Extended  
Write Multiple FUA Extended  
Write Sectors  
39  
H
CE  
H
30  
31  
34  
H
Write Sectors Without Retries  
Write Sectors Extended  
H
H
48  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
                                                                   
4.3.1  
Identify Device command  
The Identify Device command (command code EC ) transfers information about the drive to the host following  
H
power up. The data is organized as a single 512-byte block of data, whose contents are shown in Table 16 on  
page 47. All reserved bits or words should be set to zero. Parameters listed with an “x” are drive-specific or  
vary with the state of the drive. See Section 2.0 on page 3 for default parameter settings.  
The following commands contain drive-specific features that may not be included in the Serial ATA specifica-  
tion.  
Word  
Description  
Value  
0C5A  
Configuration information:  
• Bit 15: 0 = ATA; 1 = ATAPI  
• Bit 7: removable media  
• Bit 6: removable controller  
• Bit 0: reserved  
H
0
1
Number of logical cylinders  
16,383  
2
ATA-reserved  
0000  
16  
H
3
Number of logical heads  
4
Retired  
0000  
0000  
H
H
5
Retired  
6
Number of logical sectors per logical track: 63  
Retired  
003F  
H
H
7–9  
10–19  
20  
0000  
Serial number: (20 ASCII characters, 0000 = none)  
ASCII  
H
Retired  
Retired  
Obsolete  
0000  
0400  
0000  
x.xx  
H
H
H
21  
22  
23–26  
Firmware revision (8 ASCII character string, padded with blanks to end  
of string)  
27–46  
47  
Drive model number: (40 ASCII characters, padded with blanks to end  
of string)  
(Bits 7–0) Maximum sectors per interrupt on Read multiple and Write  
multiple (16)  
8010  
0000  
H
48  
Reserved  
H
49  
Standard Standby timer, IORDY supported and may be disabled  
ATA-reserved  
2F00  
H
H
H
H
H
50  
0000  
0200  
0200  
0007  
51  
PIO data-transfer cycle timing mode  
Retired  
52  
53  
Words 54–58, 64–70 and 88 are valid  
Number of current logical cylinders  
Number of current logical heads  
Number of current logical sectors per logical track  
Current capacity in sectors  
54  
xxxx  
xxxx  
xxxx  
xxxx  
xxxx  
H
55  
H
H
H
H
56  
57–58  
59  
Number of sectors transferred during a Read Multiple or Write Multiple  
command  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
49  
   
Word  
Description  
Value  
60–61  
Total number of user-addressable LBA sectors available  
(see Section 2.2 for related information)  
0FFFFFFFh*  
*Note: The maximum value allowed in this field is: 0FFFFFFFh  
(268,435,455 sectors, 137 Gbytes). Drives with capacities over 137  
Gbytes will have 0FFFFFFFh in this field and the actual number of  
user-addressable LBAs specified in words 100-103. This is required  
for drives that support the 48-bit addressing feature.  
62  
63  
Retired  
0000  
H
Multiword DMA active and modes supported (see note following this  
table)  
xx07  
H
64  
65  
66  
Advanced PIO modes supported (modes 3 and 4 supported)  
Minimum multiword DMA transfer cycle time per word (120 nsec)  
0003  
0078  
0078  
H
H
H
Recommended multiword DMA transfer cycle time per word (120  
nsec)  
67  
Minimum PIO cycle time without IORDY flow control (240 nsec)  
Minimum PIO cycle time with IORDY flow control (120 nsec)  
ATA-reserved  
00F0  
H
H
H
H
68  
0078  
0000  
0000  
69–74  
75  
Queue depth  
76  
Serial ATA capabilities  
xxxx  
xxxx  
xxxx  
xxxx  
H
77  
Reserved for future Serial ATA definition  
Serial ATA features supported  
Serial ATA features enabled  
H
H
H
78  
79  
80  
Major version number  
003E  
H
81  
Minor version number  
0000  
H
82  
Command sets supported  
364B  
H
83  
Command sets supported  
7C03  
H
84  
Command sets support extension  
Command sets enabled  
4003  
H
85  
30xx  
H
86  
Command sets enabled  
0001  
4000  
H
H
H
87  
Command sets enable extension  
Ultra DMA support and current mode (see note following this table)  
Security erase time  
88  
xx3F  
89  
0000  
0000  
H
H
90  
Enhanced security erase time  
Master password revision code  
Hardware reset value (see description following this table)  
ATA-reserved  
92  
FFFE  
H
93  
xxxx  
H
95–99  
0000  
H
50  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Word  
Description  
Value  
100–  
103  
Total number of user-addressable LBA sectors available (see Section  
2.2 for related information). These words are required for drives that  
support the 48-bit addressing feature. Maximum value:  
0000FFFFFFFFFFFFh.  
ST3750640AS = 1,465,149,168  
ST3750840AS = 1,465,149,168  
ST3500630AS = 976,773,168  
ST3500830AS = 976,773,168  
ST3400620AS = 781,422,768  
ST3400820AS = 781,422,768  
ST3320620AS = 625,142,448  
ST3320820AS = 625,142,448  
ST3300620AS = 586,072,368  
ST3300820AS = 586,072,368  
ST3250620AS = 488,397,168  
ST3250820AS = 488,397,168  
ST3250410AS = 488,397,168  
ST3250310AS = 488,397,168  
ST3200820AS = 390,721,968  
ST3160815AS = 312,581,808  
ST3160310AS = 312,581,808  
ST3160215AS = 312,581,808  
ST3120815AS = 234,441,648  
ST3120215AS = 234,441,648  
ST380815AS = 156,301,488  
ST380215AS = 156,301,488  
ST340815AS = 78,165,360  
ST340215AS = 78,165,360  
104–  
127  
ATA-reserved  
0000  
H
128  
Security status  
0001  
H
129–  
159  
Seagate-reserved  
xxxx  
H
160–  
254  
ATA-reserved  
Integrity word  
0000  
xxA5  
H
H
255  
Note. Advanced Power Management (APM) and Automatic Acoustic Management (AAM) features are not supported  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
51  
Note. See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data.  
Description (if bit is set to 1)  
Bit  
0
Word 63  
Multiword DMA mode 0 is supported.  
Multiword DMA mode 1 is supported.  
Multiword DMA mode 2 is supported.  
Multiword DMA mode 0 is currently active.  
Multiword DMA mode 1 is currently active.  
Multiword DMA mode 2 is currently active.  
Word 88  
1
2
8
9
10  
Bit  
0
Ultra DMA mode 0 is supported.  
Ultra DMA mode 1 is supported.  
Ultra DMA mode 2 is supported.  
Ultra DMA mode 3 is supported.  
Ultra DMA mode 4 is supported.  
Ultra DMA mode 5 is supported.  
Ultra DMA mode 6 is supported.  
Ultra DMA mode 0 is currently active.  
Ultra DMA mode 1 is currently active.  
Ultra DMA mode 2 is currently active.  
Ultra DMA mode 3 is currently active.  
Ultra DMA mode 4 is currently active.  
Ultra DMA mode 5 is currently active.  
Ultra DMA mode 6 is currently active.  
1
2
3
4
5
6
8
9
10  
11  
12  
13  
14  
52  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
4.3.2  
Set Features command  
This command controls the implementation of various features that the drive supports. When the drive receives  
this command, it sets BSY, checks the contents of the Features register, clears BSY and generates an inter-  
rupt. If the value in the register does not represent a feature that the drive supports, the command is aborted.  
Power-on default has the read look-ahead and write caching features enabled. The acceptable values for the  
Features register are defined as follows:  
Table 17:  
Set Features command values  
02  
03  
Enable write cache (default).  
H
H
Set transfer mode (based on value in Sector Count register).  
Sector Count register values:  
00 Set PIO mode to default (PIO mode 2).  
H
01 Set PIO mode to default and disable IORDY (PIO mode 2).  
H
08 PIO mode 0  
H
09 PIO mode 1  
H
0A PIO mode 2  
H
0B PIO mode 3  
H
0C PIO mode 4 (default)  
H
20 Multiword DMA mode 0  
H
21 Multiword DMA mode 1  
H
22 Multiword DMA mode 2  
H
40 Ultra DMA mode 0  
H
41 Ultra DMA mode 1  
H
42 Ultra DMA mode 2  
H
43 Ultra DMA mode 3  
H
44 Ultra DMA mode 4  
H
45 Ultra DMA mode 5  
H
46 Ultra DMA mode 6  
H
10  
55  
82  
90  
Enable use of SATA features  
H
H
H
H
Disable read look-ahead (read cache) feature.  
Disable write cache  
Disable use of SATA features  
AA  
Enable read look-ahead (read cache) feature (default).  
Report full capacity available  
H
F1  
H
Note. At power-on, or after a hardware or software reset, the default values of the features are as indi-  
cated above.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
53  
 
4.3.3  
S.M.A.R.T. commands  
S.M.A.R.T. provides near-term failure prediction for disc drives. When S.M.A.R.T. is enabled, the drive moni-  
tors predetermined drive attributes that are susceptible to degradation over time. If self-monitoring determines  
that a failure is likely, S.M.A.R.T. makes a status report available to the host. Not all failures are predictable.  
S.M.A.R.T. predictability is limited to the attributes the drive can monitor. For more information on S.M.A.R.T.  
commands and implementation, see the Draft ATA-5 Standard.  
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 ) that elimi-  
H
nates unnecessary drive returns. The diagnostic software ships with all new drives and is also available at:  
This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that  
supports S.M.A.R.T. to enable this feature. The table below shows the S.M.A.R.T. command codes that the  
drive uses.  
Table 18:  
S.M.A.R.T. commands  
Code in features register  
S.M.A.R.T. command  
D0  
D2  
D3  
D4  
D5  
D6  
D8  
D9  
S.M.A.R.T. Read Data  
H
H
H
H
H
H
H
H
S.M.A.R.T. Enable/Disable Attribute Autosave  
S.M.A.R.T. Save Attribute Values  
S.M.A.R.T. Execute Off-line Immediate (runs DST)  
S.M.A.R.T. Read Log Sector  
S.M.A.R.T. Write Log Sector  
S.M.A.R.T. Enable Operations  
S.M.A.R.T. Disable Operations  
S.M.A.R.T. Return Status  
DA  
H
Note. If an appropriate code is not written to the Features Register, the command is aborted and 0x04  
(abort) is written to the Error register.  
54  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
 
5.0  
Seagate Technology support services  
Online services  
Internet  
For information regarding Seagate products and services, visit www.seagate.com. Worldwide support is  
available 24 hours daily by email for your questions.  
Presales Support:  
Technical Support:  
Warranty Support:  
mySeagate  
my.seagate.com is the industry's first Web portal designed specifically for OEMs and distributors. It provides  
self-service access to critical applications, personalized content and the tools that allow our partners to  
manage their Seagate account functions. Submit pricing requests, orders and returns through a single,  
password-protected Web interface-anytime, anywhere in the world.  
spp.seagate.com  
spp.seagate.com supports Seagate resellers with product information, program benefits and sales tools. You  
may register for customized communications that are not available on the web. These communications contain  
product launch, EOL, pricing, promotions and other channel-related information. To learn more about the  
benefits or to register, go to spp.seagate.com, any time, from anywhere in the world.  
Seagate Service Centers  
Presales Support  
Our Presales Support staff can help you determine which Seagate products are best suited for your specific  
application or computer system, as well as product availability and compatibility.  
Technical Support  
Seagate technical support is available to assist you online at support.seagate.com or through one of our call  
centers. Have your system configuration information and your “ST” model number available.  
SeaTDD(+1-405-324-3655) is a telecommunications device for the deaf (TDD). You can send questions or  
comments 24 hours daily and exchange messages with a technical support specialist during normal business  
hours for the call center in your region.  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
55  
   
Customer Service Operations  
Warranty Service  
Seagate offers worldwide customer support for Seagate products. Seagate distributors, OEMs and other direct  
customers should contact their Seagate Customer Service Operations (CSO) representative for warranty-  
related issues. Resellers or end users of drive products should contact their place of purchase or Seagate  
warranty service for assistance. Have your serial number and model or part number available.  
Data Recovery Services  
Seagate offers data recovery services for all formats and all brands of storage media. Our data recovery  
services labs are currently located throughout the world. . Additional information, including an online request  
form and data loss prevention resources, is available at http://services.seagate.com/index.aspx  
Authorized Service Centers  
Seagate Service Centers are available on a global basis for the return of defective products. Contact your  
customer support representative for the location nearest you.  
USA/Canada/Latin America support services  
For an extensive list of telephone numbers to technical support, presales and warranty service in USA/  
Canada/Latin America, including business hours, go to the "Contact Us" page on www.seagate.com.  
Global Customer Support  
Presales, Technical, and Warranty Support  
Call Center  
USA, Canada,  
and Mexico  
Toll-free  
Direct dial  
1-800-SEAGATE  
+1-405-324-4700  
Data Recovery Services  
Call Center  
Toll-free  
Direct dial  
FAX  
USA, Canada,  
and Mexico  
1-800-475-01435  
+1-905-474-2162  
1-800-475-0158  
+1-905-474-2459  
Europe, the Middle East and Africa Support Services  
For an extensive list of telephone numbers to technical support, presales and warranty service in Europe, the  
Middle East and Africa, go to the "Contact Us" page on www.seagate.com.  
Asia/Pacific Support Services  
For an extensive list of telephone numbers to technical support, presales and warranty service in Asia/Pacific,  
go to the "Contact Us" page on www.seagate.com.  
Publication feedback survey  
We are interested in your comments and suggestions regarding this publication. Please take a few minutes to  
participate in our survey at the following URL:  
Thank you for your time and comments.  
56  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Device Configuration Freeze Lock 47  
Device Configuration Identify 47  
Device Configuration Restore 47  
Device Configuration Set 47  
Device Reset 47  
dimensions 43, 44  
disc surface 30  
dissipation 30  
Download Microcode 47  
duty cycle 37  
Index  
A
ACA 38  
acceleration 34  
acoustics 35  
Active 32  
Active mode 32  
actuator arm 30  
AFR 37  
E
Agency certification 37  
altitude 33  
Electrical fast transient 36  
Electromagnetic compatibility 37  
Electromagnetic Compatibility (EMC) 38  
Electromagnetic Compatibility control Regulation 38  
Electromagnetic Compatibility Directive (89/336/EEC)  
Ambient temperature 33  
ambient temperature 29, 30  
Annualized Failure Rate 37  
Annualized Failure Rate (AFR) 37  
areal density 1, 27  
ATA commands 47  
Electromagnetic immunity 36  
Electrostatic discharge 36  
electrostatic discharge (ESD) 41  
EN 55022, Class B 37  
EN 55024 37  
EN 60950 37  
Australia/New Zealand Standard AS/NZS3548 1995  
Australian Communication Authority (ACA) 38  
Australian C-Tick 38  
Average latency 29  
Average seek time 29  
enclosures 38  
Environmental specifications 33  
error-correction algorithms 1  
errors 37  
B
buffer 28  
ESD 41  
EU RoHS directive 39  
European Union (EU) requirements 37  
Execute Device Diagnostics 47  
C
cables and connectors 42  
cache 28  
capacity 26  
case temperature 33  
CE mark 37  
certification 37  
Check Power Mode 47  
China RoHS directive 39  
compatibility 37  
Conducted noise 31  
Conducted RF immunity 36  
Configuring the drive 41  
connectors 42  
F
FCC verification 38  
features 1  
Flush Cache 47  
Flush Cache Extended 47  
Format Track 47  
Formatted capacity 26  
G
Corrosive environment 39  
CSA C22.2 (950) 37  
cycles 37  
geometry 26  
guaranteed sectors 26  
Cylinders 26  
H
D
Handling precautions 41  
heads 26  
height 28  
data-transfer rates 1  
DC power 30  
Default logical geometry 26  
density 27  
humidity 33  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
57  
Operating power 30  
Operating shock 33  
Operating vibration 34  
I
I/O data-transfer rate 27  
I/O duty cycle 37  
Identify Device 47  
Identify Device command 49  
Idle 32, 47  
Idle Immediate 47  
Idle mode 30, 32  
IEC950 37  
Information Technology Equipment (ITE) 37  
Initialize Device Parameters 47  
Input noise ripple 31  
input voltage 30  
P
Physical characteristics 28  
point-to-point 2, 42  
Power consumption 30  
power consumption 30  
power dissipation 30  
Power modes 32  
Power specifications 30  
Power-management modes 32  
Power-on to Ready 29  
power-on-hours 37  
interface 27, 45  
interference 38  
precautions 41  
printed circuit board 41  
programmable power management 32  
internal data-transfer rate OD 27  
ISO document 7779 35  
ITE 37  
Q
K
quick reference 3  
Korea Ministry of Information and Communication  
(MIC) 38  
Korean RRL 38  
R
Radiated RF immunity 36  
radio and television interference 38  
radio frequency (RF) 36  
random seeks 30  
L
latency 29  
Read Buffer 47  
Read DMA 47  
Read DMA Extended 47  
Read DMA without Retries 47  
read errors 37  
latency time 30  
LBA mode 26  
length 28  
logical geometry 26  
Read Log Ext 47  
Read Multiple 47  
M
maintenance 37  
master/slave 2  
maximum temperature 33  
Mean Time Between Failures 37  
MIC 38  
Read Multiple Extended 47  
Read Native Max Address 47  
Read Native Max Address Extended 47  
Read Sectors 47  
Read Sectors Extended 47  
Read Sectors Without Retries 47  
Read Verify Sectors 47  
Read Verify Sectors Extended 47  
Read Verify Sectors Without Retries 47  
read/write actuator arm 30  
Read/write heads 26  
mounting 43  
mounting screws 33  
mounting the drive 41  
MTBF 37  
N
Read/write power 30  
noise 31  
Recalibrate 47  
nominal power 29  
recording density 27  
recording method 27  
Recording technology 27  
relative humidity 33  
Nonoperating shock 34  
Nonoperating vibration 34  
Nonrecoverable read errors 37  
Reliability 37  
RMS read/write current 31  
O
operating 30  
58  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
RoHS 39  
RRL 38  
static-discharge 41  
subassembly 38  
support services 55  
Surge immunity 36  
S
S.M.A.R.T. Disable Operations 48  
S.M.A.R.T. Enable Operations 48  
S.M.A.R.T. Enable/Disable Autosave 48  
S.M.A.R.T. Execute Offline 48  
S.M.A.R.T. implementation 47  
S.M.A.R.T. Read Attribute Thresholds 48  
S.M.A.R.T. Read Data 48  
S.M.A.R.T. Read Log Sector 48  
S.M.A.R.T. Return Status 48  
S.M.A.R.T. Save Attribute Values 48  
S.M.A.R.T. Write Log sector 48  
Safety certification 37  
SATA 45  
T
technical support services 55  
temperature 29, 33  
temperature gradient 33  
timer 32  
timers 32  
track density 27  
Track-to-track 29  
Track-to-track seek time 29  
U
UL 1950 37  
screws 33  
sectors 26  
V
Sectors per track 26  
Security Disable Password 47  
Security Erase Prepare 47  
Security Erase Unit 48  
Security Freeze 48  
Vibration 34  
voltage 30  
Voltage dips, interrupts 36  
Voltage tolerance 31  
Security Set Password 48  
Security Unlock 48  
Seek 48  
seek mode 30  
Seek mode power 30  
Seek time 29  
Seeking 30  
Serial ATA (SATA) interface 45  
serial ATA ports 2  
Servo electronics 30  
servo electronics 30  
Set Features 48  
Set Max Address 48  
Set Max Address Extended 48  
Set Multiple Mode 48  
Shock 33  
W
Warranty 37  
weight 28  
wet bulb temperature 33  
width 28  
Write Buffer 48  
Write DMA 48  
Write DMA Extended 48  
Write DMA FUA Extended 48  
Write DMA Without Retries 48  
Write Log Extended 48  
Write Multiple 48  
Write Multiple Extended 48  
Write Multiple FUA Extended 48  
Write Sectors 48  
single-track seeks 29  
Sleep 30, 32, 48  
Sleep mode 32  
Write Sectors Extended 48  
Write Sectors Without Retries 48  
sound 35  
Specification summary table 3  
spindle speed 27  
Spinup 30  
Spinup power 30  
Standby 30, 32, 48  
Standby Immediate 48  
Standby mode 30, 32  
standby timer 32  
Standby to Ready 29  
Start/stop times 29  
start-stop cycles 37  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
59  
60  
Barracuda 7200.10 Serial ATA Product Manual, Rev. K  
Seagate Technology LLC  
920 Disc Drive, Scotts Valley, California 95066-4544, USA  
Publication Number: 100402371, Rev. K, Printed in U.S.A.  

Transcend Information TS8GIFD25 User Manual
Toshiba Canvio 30 Portable Hard Drive HDTC610XK3B1 User Manual
Sony FD TRINITRON VEGA KV 32FV16 User Manual
Sony Ericsson UIQ C++ AND PERSONALJAVA P910 User Manual
Sony CDX L300 User Manual
Samsung SPINPOINT MP2 HM250JJ User Manual
Samsung GH68 23488A User Manual
Samsung GALAXY SHW M110S User Manual
RCA RP5415PK User Manual
Nokia 7390 User Manual