Sanus Systems NF213 User Manual

Assembly Instructions for Natural Furniture: Model NF203, NF213, NFV49  
Thank you for choosing the Natural Furniture line from Sanus Systems. If you have any questions regarding this or any other Sanus  
quickly with any issues regarding assembly or missing parts. Check carefully to make sure none of the parts are missing or defective.  
Never use defective parts. Replacement parts for products purchased from an authorized dealer will be shipped directly to you. Please  
call Sanus Systems before returning products to retail stores.  
Supplied Parts List:  
(12) Steel Cross Tube - b  
(8) Three Hole Plate - c  
(1) Front Frame - a  
(2) Glass Shelf - d  
(2) Rear Support - e  
(2) Plastic Wire Cover - f  
(4) Wire Strap - h  
(1) Top Glass Shelf - g  
Sanus Systems 2221 Hwy 36 West. St. Paul, MN 55113  
Step 2: Attach the Rear Supports  
Thread an Allen Bolt (i) through a Washer (j), through the middle hole in a Rear Support (e), through the middle hole in a Three Hole  
Plate (c) and into the middle Steel Cross Tube (b). See Diagram 2 for assistance. Repeat the process until all 4 middle Allen Bolts, the 4  
accompanying Washers, and the Rear Supports are attached to the middle Steel Cross Tubes.  
Next, thread an Allen Bolt through each hole of the Wire Strap (h), the Rear Support, each outer hole of the Three Hole Plate and into  
each outer Steel Cross Tube. See the Detailed View of Diagram 2 for assistance. Proceed to tighten all 12 Allen Bolts with the Allen  
Key (m).  
Diagram 2  
Detailed View  
b
c
e
j
i
h
Note: The Rear Supports should be positioned so the set of three holes closest  
to the edge is at the top and so the horizontal slots face the front frame.  
Step 3: Add Glass Shelves  
Install the Glass Shelves (d) so that the back of each shelf fits into the slot in the Rear Support (e) and the front of the shelf sits down  
into the groove in the Front Frame (a). See Diagram 3 for assistance.  
Diagram 3  
a
e
d
slot  
Step 4: Add Top Glass Shelf  
Place 4 Glass Protectors (l) evenly along the top of the Front Frame (a). Next, Add 2 Glass protectors to the top of each Rear Support  
(e). Proceed to place the Top Glass Shelf (g) onto the Glass Protectors. See Diagram 4 for assistance.  
Diagram 4  
g
l
a
l
e
Step 5: Add Plastic Wire Covers  
To add the Plastic Wire Covers (f) insert one edge of the Wire Cover into one of the slots in the Rear Support (e) as shown in the Top  
View of Diagram 5. Proceed to insert the other edge of the Wire Cover into the adjacent slot in the rear support. Repeat the process for  
the other Plastic Wire Cover. This completes the assembly of the NFV49.  
Note: The glass in Diagram 5 is shown as a cutaway view to provide greater detail of how the Wire Cover attaches to the rear sup-  
port.  
Top View  
Diagram 5  
f
h
slot  
slot  
e
Sanus Systems 2221 Hwy 36 West. St. Paul, MN 55113  

Wadia Digital 381 User Manual
Transcend Information microSD User Manual
Sony Ericsson Z550 User Manual
SIIG ZHL User Manual
Siemens IGWIPS200 1 User Manual
Seagate SEATOOLS ST3250824ACE User Manual
Samsung GH68_3XXXXA User Manual
Philips Docking Entertainment System DC220 User Manual
Philips CD 48 User Manual
Numark Industries AXIS 9 User Manual