Sangean Electronics Sangean Desktop Clock Radio WR5 User Manual

WR-5  
GB  
Rersion 1  
“Made for iPod” means that an electronic accessory has been designed to connect specifically to iPod, and has been certified by the developer to  
meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.  
Please note that the use of this accessory with iPod may affect wireless performance.  
iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple inc., registered in the U.S. and other countries.  
1
Table of contents  
GB  
Important safety instructions ............................................... 3-4  
Introduction .............................................................................. 5  
Controls .............................................................................. 6-10  
Remote control functions ..................................................... 11  
Using the radio for the first time ........................................... 12  
Operating your radio – AM/FM ...................................... 13-14  
Setting up the tuning step increment .................................. 15  
Display modes – FM ............................................................ 16  
FM Stereo (auto) / mono ...................................................... 17  
Presetting stations / Recalling a preset station  
inAM/FM modes ................................................................... 18  
iPod docking .................................................................... 19-22  
Setting the time format / date format ............................. 23-24  
Setting the clock time ..................................................... 25-26  
Setting the alarm clock ................................................... 27-28  
When the alarm sounds / Cancelling alarms /  
Snooze .............................................................................. 29-30  
Sleep timer ............................................................................ 31  
Time zone setting / Daylight saving time ........................... 32  
Display & Audio setup .................................................... 33-37  
Specifications ........................................................................ 38  
2
Important Safety Instructions  
9. Power sources; The radio should be operated only from the type of  
power source indicated on the marking label. If you are not sure of  
the type of power supply to your home, consult your radio dealer or  
power company.  
1. Read and understand all safety and operating instructions before the  
radio is operated.  
2. Retain instruction: The safety and operating instructions should be  
retained for future reference.  
10. Mains adaptor: The mains adaptor should be positioned so it is not  
walked on, pinched, or items placed on top of it. Pay particular  
attention to wires at plugs, convenience receptacles, and the point  
where they exit from the unit. Unplug the mains adaptor by gripping  
the adaptor, not the wire. Operate the radio using only the current  
type of power source indicated. If you are not sure of the type of  
power source supply to your home, consult your dealer or local  
power company.  
3. Heed warnings. All warnings on the appliance and operating  
instructions should be followed.  
4. Follow all operations and use instructions.  
5. Water and moisture: The appliance should not be used near water.  
Do not use near a bathtub, washbowl, laundry tub, kitchen sink,  
wet basement, swimming pool, etc.  
11. Do not overload wall outlets or extension cords. This can result in a  
risk of fire or electrical shock. Never insert objects of any kind into  
the radio through opening. The objects may touch dangerous  
voltage points or short out parts. This could cause a fire or  
electrical shock.  
6. Unplug the radio from the AC power outlet before cleaning. Use only a  
damp cloth for cleaning the exterior of the radio.  
7. Do not place the radio on an unstable cart, stand, bracket or table.  
The radio may fall, causing serious personal injury and damage to  
the radio.  
12. If the radio is left unattended and unused for long periods of time,  
unplug it from the wall outlet. This will prevent damage caused by  
lightning or power line surges.  
8. Ventilation: This radio should be situated so that its location or  
position does not interfere with its proper ventilation. For example,  
the radio should not be used on a bed, sofa, rug or other soft  
surfaces that may block the ventilation openings. It should not be  
placed in a built-in situation like a cabinet that may reduce air flow  
through the ventilation openings.  
13. If the radio is left unattended and unused for a long period of time,  
remove the batteries. The batteries may leak and damage furniture  
or your radio. (US version only)  
3
GB  
14. Do not attempt to service the receiver yourself. Removing the  
cover may expose you to dangerous voltage, and will void  
the warranty. Refer all servicing to authorized  
service personnel.  
15. Never push objects of any kind into this radio through opening as  
they may touch dangerous voltage points or short-out parts that  
could result in a fire or electric shock. Never spill liquid of any  
kind into the product.  
16. Apparatus shall not be exposed to dripping or splashing and no  
objects filled with liquids, shall be placed on the apparatus.  
17. For outdoors use, to avoid electric shock, use battery only  
during a raining day or the weather is wet.  
18. The power plug should be close to the radio, and easy to be  
approached that during the emergency, to disconnect the  
power from the radio, just unplug the power plug from the  
AC power slot.  
4
Introduction  
The Sangean WR-5 AM/FM-RDS/iPod Dock Wooden Table-top  
Receiver provides the following range of features:  
Radio for AM and FM (with RDS) broadcasts.  
12 radio station presets (6 for AM, 6 for FM).  
Large LCD display with adjustable backlight.  
Two alarm timers with snooze feature to wake you to either buzzer,  
radio alarm, or iPod.  
Adjustable sleep timer which can be set to turn the clock radio off  
after between 15 and 120 minutes.  
A 3.5mm stereo Auxiliary Input socket for playing audio from  
MP3 players, iPod devices or other audio equipment.  
iPod cradle plays and charges iPods.  
Equipped with tone control (bass/treble) and  
loudness compensation.  
Passive reflex tube and 3D expandable surround design speakers to  
enhance the sound performance.  
Remote control allows you to access all features of WR-5 and  
operate iPod more easily.  
5
Controls  
GB  
1. Speakers  
3. Remote control sensor  
2. LCD display  
6
Controls  
4. FM telescopic antenna  
5. AM external antenna terminal  
6. Ground terminal  
8. AC in  
9. Headphone jack  
10. Line out socket  
11. Aux in socket  
7. Battery compartment  
7
Controls  
GB  
12. iPod Universal Dock adjuster  
13. iPod Dock connector  
14. Info / menu button  
21. Snooze / dimmer  
22. Preset 5 / Play / pause  
23. Preset 4 / Back Forward  
24. Source  
15. Preset 3 / Repeat button  
16. Tuning control  
25. Preset 1 / Folder Down  
26. Tone button  
17. Seek / Select button  
18. Standby / Sleep timer  
19. Preset 6 / Fast Forward  
20. Preset 2 / Folder Up  
27. Volume control  
28. Alarm 1  
29. Alarm 2  
8
Display icons  
A. Battery capacity indicator  
B. PM indicator  
C. Time display  
D. Sleep timer icon  
E. Alarm 1 icon  
F. Alarm 2 icon  
G. Frequency / information for station display  
H. RDS icon  
9
Remote control  
GB  
a. Back forward  
b. Repeat one / all  
c. Tuning up  
d. Folder up / preset up  
e. Folder down / preset down  
f. Tuning down  
g. Mute  
h. Snooze / dimmer  
i. Tone  
j. Volume down  
k. Volume up  
l. Repeat random  
m.Select  
n. Fast forward  
o. Play / pause  
p. Source  
q. Menu  
r. Standby / Sleep timer  
10  
Remote control functions  
Many functions of the WR-5 tabletop receiver can be operated using the  
remote control. Some operations require a longer press of the button.  
In this case simply keep your finger held on the remote control button  
for 2-3 seconds until the display on the radio shows that the command  
has been accepted.  
Before the first operation: please remove the small transparent  
foil from the battery holder to activate the battery.  
Remote control battery replacement  
1. Open the battery holder by pulling the holder out in direction shown.  
2. Remove battery from holder.  
3. Replace battery (CR2025 or equivalent) ensuring that the positive side  
of the battery faces you with holder positioned as shown.  
4. Replace the battery holder.  
IMPORTANT:  
The batteries should not be exposed to excessive heat such  
as sunshine, fire or the like. After use, disposable batteries should if  
possible be taken to a suitable recycling center. On no account should  
batteries be disposed of by incineration.  
11  
Using the radio for the first time  
GB  
Using the AC power adaptor  
Getting started with external accessories  
The AC power adaptor required for this unit should be 12 volts AC  
at 1.6A.  
You may use an optional AM Radio Antenna as external antenna if  
satisfactory reception cannot be obtained. Connect the optional AM  
radio antenna to the AM external antenna terminal and ground  
terminal located on the rear panel. See figure 5, 6.  
Insert the adaptor plug into the AC socket on the rear of the radio.  
Plug the adaptor into a standard mains socket outlet.  
The AC adaptor should be disconnected from the main supply when not  
in use.  
Backup battery operation (for US version only)  
1. Remove the battery cover on the bottom of the unit.  
2. Insert two UM-4 (AAA size) batteries into the spaces in  
the compartment.  
3. Take care to ensure all batteries are inserted with correct polarity as  
shown inside the compartment. Replace the battery cover.  
4. When the low battery capacity indicator shows on the display please  
replace the batteries immediately.  
5. When the radio is used as clock radio or as an alarm, please always  
keep the batteries inserted.  
12  
Operating your radio – Search tuning AM/FM  
1. Press the Standby button to switch on your radio.  
2. Press the Source button as needed until the AM or FM band  
is selected.  
3. Press and release the Seek / Select button to carry out an auto-tune.  
Your radio will scan up the AM/FM band from the currently displayed  
frequency and will stop scanning automatically when it finds a station  
of sufficient strength.  
2
4. After a few seconds the display will update. The display will show the  
frequency of the signal found.  
5. To find other station, press and release the Seek / Select button  
as before.  
6. When the end of the waveband is reached your radio will  
recommence tuning from the opposite end of the waveband.  
7. Use the Volume control to adjust the sound level as required.  
8. To switch off your radio press the Standby button.  
7
13  
GB  
Manual tuning – AM/FM  
1. Press the Standby button to switch on your radio.  
2. Press and release the Source button to select AM or FM radio mode.  
3. Rotate the Tuning control to tune to a station. The FM frequency will  
change in steps of 100kHz/50kHz and AM frequency will change in  
steps of 10kHz/9kHz.  
2
4. When the end of the waveband is reached your radio will  
recommence tuning from the opposite end of the waveband.  
5. Use the Volume control to adjust the sound level as required.  
3
5
14  
Setting up the tuning step increment  
1. Press and hold the Info/menu button to enter the menu setting.  
1,4  
2. Rotate the Tuning control until FM 50/100MHz or AM 9/10kHz  
appears on the display, and press and release the Seek / Select  
button to enter the step increment setting.  
3. Rotate the Tuning control to select either 100kHz/200kHz  
(US version) or 50kHz/100kHz (European version) for FM radio,  
and 9kHz/10kHz for AM radio. Then press and release the  
Seek / Select button to confirm the setting.  
2,3  
4. Press and release the Info/menu button and the LCD will revert to the  
normal display.  
15  
Display modes – FM  
GB  
Your radio has a range of display options for FM radio mode.  
1. Repeatedly press and release the Info/menu button to view the RDS  
information of the station you are listening to.  
1
Displays the name of the station being listened to.  
Station name  
a.  
b.  
Displays the type of station being listened to such  
as Pop, Classic, News, etc.  
Program type  
Displays radio text messages such as new  
items etc.  
Radio text  
Stereo / Mono  
Year / Day  
Date / Day  
Frequency  
c.  
d.  
e.  
f.  
Displays the radio broadcasting is in Stereo or  
Mono mode.  
Displays the year and day of the week according to  
the date setting of your radio.  
Displays the date and day of the week according to  
the date setting of your radio.  
Displays the frequency of the FM for the station  
listened to.  
g.  
16  
FM stereo (auto) / mono  
If the FM radio station being listened to has a weak signal some hiss  
may be audible. It is possible to reduce this hiss by forcing the radio to  
play the station in mono rather than stereo.  
1. Press the Source button as needed to select the FM radio mode  
display and tune to the required FM station as previously described.  
2. Press and hold the Info/menu button to enter the menu setting.  
3. Rotate the Tuning control until the FM Stereo / mono setting shows  
on the display. If the setting is Auto press the Seek / Select button  
to switch to Mono mode to reduce the hiss.  
2
4. To return to Auto (stereo) mode press and release the Seek / Select  
button to alter the setting, so that the radio will switch back to  
Auto mode.  
3
17  
Presetting stations in AM/FM mode  
GB  
There are 6 preset stations each for AM and FM radio. They are used in  
the same way for each waveband.  
1. Press the Standby button to switch on your radio.  
2. Press the Source button to select the desired waveband. Tune to the  
required radio station as previously described.  
3. Press and hold the required Preset button (1 to 6) until the display  
shows “P3” for example after the frequency. The station will be  
stored using the preset number. Repeat this procedure for the  
remaining presets as you wish.  
2
3
4. Preset stations which have already been stored may be overwritten  
by following the above procedure if required.  
Recalling a preset in AM/FM mode  
1. Press the Standby button to switch on your radio.  
2. Select the required waveband by pressing the Source button.  
3. Momentarily press the required Preset button to cause your radio to  
tune to one of the stations stored in the preset memory.  
Note:  
the remote control can only recall preset stations.  
Presetting stations can’t be operated by remote control.  
18  
iPod docking  
Your radio has an iPod docking facility which allows you to play digital  
audio files and soundtracks held on your iPod directly.  
Your radio uses the iPod Universal Dock adjustor developed for use  
with iPods. Recent models of iPod are supplied with Universal Dock  
Adapter inserts which ensure correct alignment of the iPod with the  
electrical connector.  
Important:  
The radio does not support iPod 3rd generation (build 2003-2004).  
To avoid possible damage to your iPod, do not use your iPod with  
the product without the correct adapter fitted to the radio.  
Docking you iPod by dock adjuster  
This unit comes with the iPod dock adjuster. iPod adaptors are  
not supplied.  
1. Press and turn the iPod dock adjuster dial to move slide door  
backward until end.  
2. Carefully place your iPod onto the cradle.  
3. Turn the iPod dock adjuster dial to move slide door forwards until  
holding your iPod.  
19  
Charging your iPod  
GB  
1. Place the iPod onto the Universal Dock Adjuster into the iPod  
docking compartment. Press the STANDBY button to switch on  
your radio.  
2. Press SOURCE button until “iPod” shows on the display. Your radio  
is able to recharge your iPod’s internal battery when the source is  
Aux In, iPod or Standby mode. Your iPod won’t be charged under  
AM and FM mode.  
2
20  
Navigating your iPod  
Playing an audio file / repeat playing files on  
your iPod  
To navigate your iPod menus to make selections or to change settings,  
you should use your iPod controls. The radio controls can be used for  
Menu / Select, Previous / Next, Fast Rewind / Fast Forward and  
Play / Pause functions.  
1. When you have found the required item, use the Tuning/Seek/Select  
control on the radio to start the iPod playing.  
2. Adjust the volume to the required setting using the Volume control on  
your radio.  
1. Use the Menu button to navigate to higher level menus on your iPod.  
2. Rotate the Tuning control as required to move up or down a menu  
screen on your iPod.  
3. To pause playback press the Play/Pause button. To resume playback  
press the Play/Pause button again.  
3. Press the Seek / Select button to choose the highlighted on screen  
menu item. If this item is a lower level menu item, you may then  
navigate further using the Tuning/Seek/Select control.  
4. iPods do not have a Stop button (they use the Pause function).  
To play an alternative selection, use the iPod menus to make the  
selection using the Play/Pause button to stop playing the current  
item if needed.  
5. If it was previously playing, your iPod will switch on and continue  
playing from where it was previously stopped.  
6. To select the various repeating modes, press and release the Repeat  
button (Preset 3) to repeat one/all/folder or repeat random.  
21  
Search function  
Your WR-5 works with the following models of iPod:  
GB  
1. Press and release either the Fast-Forward or Back-forward button to  
start playing the next or previous track.  
2. While the iPod is playing, press and hold the Fast-Forward or  
Back-forward buttons to move through the current file or track,  
and then release the button when the desired point in the file or track  
is reached.  
22  
Clock and Alarms  
Setting the time format  
The clock display used in stand-by mode and on the playing mode  
screens can be set to 12 or 24 hour format. The selected format is  
then also used when setting the alarms.  
1. Press and hold the Info/menu button to enter the menu setting.  
1,4  
2. Rotate the Tuning control until CLOCK 12H/24H appears on  
the display, then press and release the Seek / Select button to enter  
the setting and the setting of time format begins to flash.  
3. Rotate the Tuning control to select either 12 or 24 hour format.  
Press and release the Seek / Select button to confirm your choice of  
clock format. The display will then revert to the previous menu.  
2,3  
4. Press and release the Info/menu button and the LCD will revert to the  
normal display.  
If the 12 hour clock format is chosen, the radio will then use the12 hour  
clock for the setting of alarms with a PM indicator.  
23  
Setting the date format  
GB  
1. Press and hold the Info/menu button to access the menu setting.  
2. Rotate the Tuning control until date format ex. “Jan-xx-2010” shows  
on the display. Press and release the Seek / Select button to enter  
the date format setting.  
3. Rotate the Tuning control to select the required date format.  
Press and release the Seek / Select button to confirm your choice of  
date format. The display will then revert to the previous menu.  
4. Press and release the Info/menu button and the LCD will revert to  
normal display.  
24  
Setting the clock time manually  
1. Press the Standby button to switch on your radio.  
2. Press and hold the Info/menu button.  
3. Rotate the Tuning control until a clock symbol appears on the left  
side display, then press and release the Seek / Select button to  
enter the setting. Rotate the Tuning control until MANUAL appears  
on the display, then press and release the Seek / Select button to  
select the setting.  
2,8  
4. Rotate the Tuning control until CLOCK appears on the display.  
Press and release the Seek / Select button to enter the setting.  
5. The hour setting on the display will begin flashing. Rotate the Tuning  
control to select the desired hour, and press and release the  
Seek / Select button to confirm the setting. Then rotate the Tuning  
control to select the desired minute, and press and release the  
Seek / Select button to confirm the setting.  
3-7  
6. Rotate the Tuning control until DATE appears on the display.  
Press and release the Seek / Select button to enter the setting.  
7. The year setting will begin to flash. Rotate the Tuning control to  
select the desired year, and press and release the Seek / Select  
button to confirm the setting. Then rotate the Tuning control to select  
the desired month, and press and release the Seek / Select button  
to confirm the setting. Then rotate the Tuning control to select the  
desired date. Press and release the Seek / Select button to confirm  
the setting and the radio will beep once.  
8. Press and release the Info/menu button to leave the current setting,  
and the radio will revert to normal display.  
25  
Setting the clock time using RDS CT  
GB  
1. When tuning to a station transmitting RDS data, press and hold the  
Info/menu button.  
1,4  
2. Rotate the Tuning control until a clock symbol appears on  
the display. Press and release the Seek / Select button to enter  
the setting.  
3. Rotate the Tuning control until RDS CT appears on the display.  
Press and release the Seek / Select button to confirm the setting.  
The clock time of the radio will set up automatically according to the  
RDS data received. When the action is completed, the RDS icon will  
appear on the LCD display indicating the radio time is RDS  
clock time. The radio cock time will be valid for 5 days each time the  
radio time is synchronized with RDS CT.  
2,3  
4. Press and release the Info/menu button and the LCD will revert to the  
normal display.  
26  
Setting the alarm clock  
Your WR-5 has two alarms which can each be set to wake you to  
AM/FM radio, buzzer alarm or iPod. The alarms may be set while the  
unit is in standby mode or while playing.  
1. Before setting an alarm ensure that the clock time is set. Press and  
hold the Alarm 1 button to enter the alarm 1 setting.  
2. The hour setting of alarm 1 will begin to flash. Rotate the Tuning  
control to select the required alarm hour, and press and release the  
Seek / Select button to confirm the setting. Rotate the Tuning control  
to select the required alarm minute, and press and release the  
Seek / Select button to confirm the setting.  
2-6  
3. Then the display will show the frequency options for the alarm.  
The alarm options are as follows:  
ONCE – the alarm will sound once  
DAILY – the alarm will sound everyday  
WEEKDAY – the alarm will sound only on weekdays  
WEEKEND – the alarm will sound only at weekends  
Press and release the Seek / Select button to confirm the setting.  
27  
GB  
4. Rotate the Tuning control to choose the required alarm type,  
and then press and release the Seek / Select button to confirm  
the setting. The alarm can be set to buzzer, iPod, FM or AM.  
When radio mode is selected, the radio frequency and the preset  
number on the display will begin to flash. Rotate the Tuning control  
to adjust the required radio frequency or the required preset  
number for the radio alarm, then press and release the  
Seek / Select button to confirm the setting.  
Note:  
If the alarm type selected is iPod but your iPod is not docked when the  
alarm is sounding, the buzzer alarm will be used instead.  
5. Rotate the Tuning control to choose the required sound level for  
the alarm. Press and release the Seek / Select button to confirm  
the setting.  
6. The alarm has now been set. Press and release the Seek / Select  
button again, and the radio will revert to normal display.  
Active alarms are shown using alarm indicator on the display.  
28  
When the alarm sounds  
To cancel a sounding alarm, press and hold the Alarm 1 or Alarm 2  
button until the alarm indicator on the display disappears.  
When the buzzer alarm activates, the alarm will start softly and  
gradually increase in level. It will sound for 1 minute and silence for  
1 minute in repetition for 60 minutes unless cancelled. The radio will  
sound non-stop at the selected time for up to 60 minutes for other  
alarm types.  
Disabling / cancelling alarms  
To disable an active alarm, either press and release the Standby button,  
or press and hold the according alarm button to cancel the alarm.  
29  
Snooze  
GB  
1. When the alarm sounds, press any button other than the Standby  
button will silence the alarm for 5 minutes. “SNOOZE’ will appear on  
the display.  
2
2. To adjust the silence time for the snooze timer, press and hold the  
Info/menu button to enter the menu setting.  
3. Rotate the Tuning control until “SNOOZE 5” appears on the display,  
then press and release the Seek / Select button to enter the setting.  
Rotate the Tuning control to adjust the silence time from 5, 10, 15  
and 20 minutes for the snooze timer.  
3
4. To cancel the snooze timer while the alarm is suspended, press and  
release the Standby button.  
30  
Sleep timer  
Your radio can be set to turn off automatically after a preset time  
has elapsed. The Sleep Timer setting can be adjusted between  
15, 30, 45, 60, 90 and 120 minutes.  
1. Press and hold the Standby button to enter the Sleep Timer setting.  
“SLEEP XX” will show on the display.  
1-2,4  
2. Keep pressing the Standby button and the Sleep Timer options will  
start switching on the display. Stop until the required Sleep Timer  
setting appears on the display. The setting will be saved and the LCD  
will return to normal display.  
3. Your radio will switch off automatically after the preset Sleep Timer  
has elapsed. The Sleep Timer icon will show on the display indicating  
an active Sleep Timer.  
4. To cancel the Sleep Timer function before the preset time  
has elapsed, simply press and release the Standby button to turn the  
unit off manually.  
31  
Time zone setting  
GB  
Your WR-5 can set up the time zone for its radio clock time.  
1. Press and hold the Info/menu button to enter the menu setting.  
1,4  
2. Rotate the Tuning control until TIME ZONE appears on the display.  
Press and release the Seek / Select button to enter the setting.  
3. Rotate the Tuning control to choose the Time zone setting for  
your area, then press and release the Seek / Select button to confirm  
the setting.  
2,3  
4. Press and release the Info/menu button and the LCD will revert to the  
normal display.  
Daylight Saving Time  
1. Press and hold the Info/menu button to enter the menu setting.  
1,4  
2. Rotate the Tuning control until “DST OFF” appears on the display.  
Press and release the Seek / Select button to enter the setting.  
3. Rotate the Tuning control to choose +1H to set the clock  
1 hour faster, and press and release the Seek / Select button to  
confirm the setting.  
2-4  
4. To set the clock back from D.S.T., choose OFF and then press and  
release the Seek / Select button.  
32  
Display & Audio setup  
Dimmer control  
The brightness of the display may be adjusted. If you use the unit in  
the bedroom, you may prefer a higher brightness level than the  
standard setting.  
1. Press and release the Snooze/Dimmer button repeatedly to adjust  
the brightness level of the LCD display. The backlight level will  
change with 8 different illumination levels so that you can see the  
effect of the change.  
2. Stop when the desired backlight level is selected.  
Tone control  
You can adjust the bass and treble of the sound of your WR-5 to  
enhance the tone while listening.  
1. First ensure your radio is switched on. Press and release the Tone  
control to enter the tone control setting.  
2. The bass value will appear on the display. Rotate the Volume control  
to adjust between -5~+5, and press and release the Tone control to  
confirm the setting.  
1-3  
3. Then the treble value will appear on the display. Rotate the Volume  
control to adjust between -5~+5, and press and release the Tone  
control to confirm the setting.  
33  
Loudness  
GB  
You can get compensation on lower and higher frequency for your WR-5  
by adjusting the Loudness function.  
1. Press and hold the Info/menu button to enter the menu setting.  
1
2. Rotate the Tuning control until LOUD ON/OFF appears on  
the display. Press and release the Seek / Select button to enter  
the setting.  
3. Rotate the Tuning control to choose ON to turn on the  
Loudness function, then press and release the Seek / Select button  
to confirm the setting.  
2-4  
4. To turn off the Loudness function, select OFF and press and release  
the Seek / Select button to confirm the setting.  
34  
3D surround sound expander  
Your WR-5 allows you to get more spaciousness in the sound  
performance with the 3D surround expander function.  
1. Press and hold the Info/menu button to enter the menu setting.  
1
2. Rotate the Tuning control until 3D ON/OFF appears on the display.  
Press and release the Seek / Select button to enter the setting.  
3. Rotate the Tuning control to choose ON to turn on the 3D surround  
expander function, then press and release the Seek / Select button  
to confirm the setting.  
2-4  
4. To turn off the 3D expander function, select OFF and press and  
release the Seek / Select button to confirm the setting.  
35  
Auxiliary input socket  
GB  
A 3.5mm stereo Auxiliary Input socket is provided on the rear of your  
radio to permit an audio signal to be fed into the unit from an external  
audio device such as iPod, MP3 or CD player.  
1. Repeatedly press and release the SOURCE button until AUX IN  
is displayed.  
2. Connect an external audio source (for example, iPod, MP3 or  
CD player) to the Auxiliary Input socket.  
3. Adjust the volume setting on your iPod, MP3 or CD player to ensure  
an adequate signal level from the player, and then use the Volume  
control on the radio as needed for comfortable listening.  
3
Headphone socket  
A 3.5mm stereo Headphone Socket is provided on the rear of your radio  
for use with headphones. Inserting a plug automatically mutes the  
internal loudspeaker.  
IMPORTANT:  
Excessive sound pressure from earphones and headphones can cause  
hearing loss.  
Line out socket  
The radio can be used as a separate tuner by connecting the input to  
Hi-Fi system, or using this input to make recording in stereo from  
audio program.  
36  
Software version  
The software display cannot be altered and is just for your reference.  
1. Press and hold the Info/menu button to enter the menu setting.  
1
2. Rotate the Tuning control until VER 1.XX appears on the display to  
view the software version of your radio.  
2
Note:  
Most of the remote control operation of WR-5 is the same with operation  
on the radio, except some functions like the following:  
1. Mute function: press the mute button on the remote control, and the  
receiver will be muted and MUTE will appear on the display.  
To disable the mute function, press the mute button again.  
2. Repeat function: press the button while the radio is playing your  
iPod to choose from repeating one file, repeating all files or turning off  
repeat function. Press the button to choose random repeat mode.  
37  
Specifications  
Circuit Features  
GB  
Power Requirements  
Loudspeaker 2.25” 6 ohm x 2 full range  
Output Power: 5W+5W  
Mains AC 12V~/1.6A  
Frequency Range  
FM: 87.5 – 108 MHz  
Headphone socket 3.5mm dia stereo  
Auxiliary socket 3.5mm dia stereo  
Line out socket 3.5mm dia stereo  
AM: 520 – 1710 kHz (US version)  
522 – 1629 kHz (European version)  
Back-up Battery  
Aerial System: FM telescopic antenna  
2 x 1.5V Size “AAA” / UM-4 / LR3  
If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be  
disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling  
advice. (Waste Electrical and Electronic Equipment Directive)  
38  

Tannoy HCB 700 User Manual
Seagate U8TM FAMILY ST38410A User Manual
Sangean Electronics H202 User Manual
Samsung Spinpiont F3 HM080II User Manual
Samsung SGH I547C User Manual
Roberts Radio CR950 User Manual
Polycom Seimens ROLM PBX User Manual
Philips Cell Phone SA3CNT08 User Manual
Nokia 8290 User Manual
Nokia 6310 User Manual