[ RX358 Series ]
3.5" SATA HDD to USB & eSATA
Ext. Enclosure w/Int.80mm fan
User Manual
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ]
Enclosure Figure Description
Front View
User Manual
A
B
Rear View
C
G
D
E
F
A. Ventilation design 1 B. Ventilation design 2
C. Fan Switch
E. Power Jack
G. eSATA Port
D. Power Switch
F. USB Port
2
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ]
User Manual
User Assembly Guide
z Please follow the instructions and make sure your HDD is
successfully installed to the mobile disk!
STEP1: Release the 4 screws, and then remove the bottom
aluminum cover.
3
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ]
User Manual
STEP2: Release 2 screws from back panel, and then slide out the
side plates.
STEP3: Place HDD into the enclosure properly. Connect HDD to
SATA connector.
4
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ]
User Manual
STEP4: Tight up 4 screws from side to side.
STEP5: Reassemble two side plates back to the enclosure and fix
the screws.
5
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ]
User Manual
STEP6: Replace the aluminum cover back and tight up 4 screws.
Attention
1. Make sure HDD does not dash the leaves of fan during
assembly.
2. Please leave at least 5cm from air intake ventilator.
6
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ]
User Manual
HDD Formatting Guide
z You may format your external HDD through USB2.0 connection.
z Please make sure your external HDD is turned on and well
connected to the PC before formatting the HDD.
STEP1: Right-click “My Computer” icon and select the “Manage”
column.
STEP2: Select “Disk Management” and you will see your External
HDD showed “Unallocated”.
7
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ]
User Manual
STEP3: Right-click on the “Unallocated” blocks and selects “New
Partition”.
STEP4: The “New Partition Wizard” will appear. Please follow the
instruction of the wizard to complete.
8
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ]
User Manual
STEP5: When new partition is completed, the external HDD will be
recognized as a “New Volume”.
STEP6: Double-click “My Computer”. You will see the new
volume appears on your PC.
9
3.5" SATA HDD to USB & eSATA Ext. Enclosure w/Int.80mm fan [ RX358 Series ]
User Manual
NOTICE
Question：Does this SATA enclosure support hot swap?
Answer：Yes, but it depends on the motherboard you have.
1. If your motherboard has an eSATA port in the Back I/O
Connectors Panel as shown in picture # 1 your hot-swap
function is supported and there is no need to install the
eSATA bracket. All you need is connecting the enclosure
with eSATA port at the back of your computer. You can
connect/disconnect the enclosure with your computer at
anytime.
2. If your motherboard only comes with an onboard SATA port
and no eSATA port available. This mean hot-swap is not
supported by your motherboard. You will need to install an
eSATA bracket. Since hot-swap is not supported, you must
connect the enclosure with the computer while it powered off.
The computer will recognize the enclosure during the booting
sequences and you should be able to see the drive after MS
Windows boot up.
10
|