Philips Cell Phone Accessories M888 User Manual

Register your product and get support at  
M888  
Short user manual  
Important safety instructions  
Warning  
Make sure the baby unit and the cord are always  
out of reach of the baby (at least 1 metre/3 feet  
away).  
Keep the parent unit at least 1.5 metres/5 feet away  
from the baby unit to prevent acoustic feedback.  
Never place the baby unit inside the baby’s bed or  
playpen.  
The Electrical network is classified as hazardous.The  
only way to power down the charger is to unplug  
the power supply from the electrical outlet. Ensure  
that the electrical outlet is always easily accessible.  
Refer to safety information before using the  
product.  
Never cover the parent unit and the baby unit with  
anything (e.g. a towel or blanket).Always make sure  
the cooling vents of the baby unit are free.  
This appliance is not intended for use by persons  
(including children) with reduced physical, sensory  
or mental capabilities, or lack of experience  
and knowledge, unless they have been given  
supervision or instruction concerning use of the  
appliance by a person responsible for their safety.  
If you place the parent unit next to a transmitter  
or other DECT appliance (e.g. a DECT telephone  
or wireless router for the internet), the connection  
with the baby unit may be lost. Move the baby  
monitor further away from the other wireless  
appliances until the connection is restored.  
This baby monitor is intended as an aid. It is not  
a substitute for responsible and proper adult  
supervision and should not be used as such.  
This product complies with European R&TTE  
directive 1999/5/EC  
Use only the power supply listed in the user  
instructions.  
Use only the batteries listed in the user instructions.  
Do not allow the product to come into contact  
with liquids.  
Risk of explosion if battery is replaced by an  
incorrect type.  
Dispose of used batteries according to the  
instructions.  
When the handset rings or when the handsfree is  
activated, keep the handset away from your ear to  
avoid hearing damage.  
When using the phone as a baby monitor  
Children should be supervised to ensure that they  
do not play with the appliance.  
Overview  
1
Loudspeaker  
(back side)  
Earpiece  
In call  
Standby  
Display icons  
Display icons  
The number of bars indicates the connection  
/
/
Enter the option menu.  
Access the main menu.  
The speaker is on.  
OK  
OK  
status between the handset and base station.  
The more bars are shown, the better the signal  
strength is.  
Change the sound profile.  
Adjust the volume.  
Access the redial list.  
Phonebook  
The ringer is off.  
The silent mode is set and within active period  
(the phone does not ring).  
Recall (network dependent).  
End calls.  
Call log  
It remains steadily on beside the unread missed  
call record when browsing the call log.  
Answering machine: it flashes when there is a  
new message. It displays when the telephone  
answering machine is turned on.  
Make and receive calls.  
OK  
It flashes when there is a new missed call. It  
remains steadily on when browsing missed calls  
in call log.  
Turn the speaker on/off.  
Mute/unmute the microphone.  
Enter a pause (press and hold).  
Make intercom call (press and hold).  
Multi-handset version only.  
Voice messages indicator: flashes for new  
messages, is steady for reviewed messages.  
*This is network dependent  
Lock/unlock the keypad (press and hold).  
Make and receive calls through the speaker.  
The alarm is activated.  
Microphone  
The silent mode is set, but is outside of active  
period.  
ECO The ECO mode is activated.  
Find handset (back side)  
ECO+ The ECO+ mode is activated.  
In menu  
In text input  
Delete a character.  
/
Confirm / Select / Enter the option menu.  
OK  
Delete all characters (press and hold).  
Cancel  
Enter a space.  
Up / down  
Exit menu.  
Main menu icons  
Alarm  
Switch upper/lower case (press and hold).  
Left / right  
Phonebook  
Services  
Baby monitor  
Sounds  
Phone setup  
Answer machine  
Display  
Get started  
3
Configure your phone  
Charge your phone  
1 The batteries are pre-installed in the handset. Pull the  
battery tape off from the battery door before charging.  
2 When using your phone for the first time, you see a  
welcome message (country dependent).  
3 Set the country and language if prompted.  
4 Set the date and time.  
Charge 8 hours  
/
If the time is in 12-hour format, press  
to  
select [am] or [pm] (country dependent).  
Charge your handset by docking it in either direction.The  
LED at the back of the handset flashes once.  
> 84%  
36% - 52%  
18% - 36%  
< 18%  
68% - 84%  
52% - 68%  
Flashing: low battery  
Enjoy  
4
Listen to the incoming messages  
Phonebook  
Call log  
Redial list  
Select [Menu] >  
> [Play], then press [OK] to  
Add record  
1 Press > [Option] > [Add new].  
2 Follow on-screen instructions.  
Call from the call log  
Call from the redial list  
confirm.  
1 Press  
> [Incoming calls].  
1 Press [Redial].  
2 Select a record and press  
Delete an incoming message  
2 Select a record and press  
.
.
1 When you listen to the message, press [Option]  
to enter the options menu.  
2 Select [Delete], then press [OK] to confirm.  
Call from the phonebook  
View record  
Save record  
1 Press [Redial].  
2 Select a record and select [Option] >  
[Save number].  
3 Follow on-screen instructions.  
1 Press  
.
1 Press  
> [Incoming calls].  
2 Select a record and press  
.
2 Select a record and select [Option] > [View].  
Register additional handsets  
Direct access memory  
Save record  
You can register additional handsets to the base station.  
You have 9 direct access memories (Keys 1 to 9).To  
dial the saved phone number automatically, press and  
hold on the keys in standby mode.  
Depending on your country, keys 1 and 2 are  
preset to the voice mail number and information  
service number of your service provider respectively  
(network dependent).  
1 Press  
> [Incoming calls].  
1 Select [Menu].  
Delete record  
1 Press [Redial].  
2 Select a record and select [Option] > [Delete].  
3 Follow on-screen instructions.  
2 Select a record and select [Option] >  
[Save number].  
3 Follow on-screen instructions.  
/
2 Press  
to select  
> [Register].  
3 Press and hold on the base station for 5 seconds.  
4 Enter the system PIN/passcode (0000).  
Delete record  
5 Press [OK] to confirm the PIN/passcode.  
1 Press  
> [Incoming calls].  
Telephone answering machine  
Record an announcement  
1 Press [Menu].  
»
Registration is complete in less than 2 minutes.  
2 Select a record and select [Option] > [Delete].  
3 Follow on-screen instructions.  
/
2 Press  
to select  
> [Announcement].  
3 Follow on-screen instructions.  
Learn more  
5
Silent mode  
Sets time during which the phone will not ring  
> [Silent mode]  
MySound  
Customizes the sound of voices to your liking  
> [MySound]  
Eco mode  
Reduces power consumption / transmission power;  
reduces radiation and range by approximately 60%  
> [Eco mode]  
Eco+ mode  
Eliminates radiation in standby mode (causes 2  
seconds ring delay, 50% shorter standby time)  
> [ECO+ mode]  
Call barring  
Prevents unwanted outgoing calls to selected  
numbers  
> [Call barring]  
Technical data  
Battery  
Philips: 2 x AAA NiMH 1.2V Rechargeable  
550 mAh batteries  
Use only the supplied batteries.  
Adapter  
MEIC: MN-A075-U056  
Input: 100-240V~ 50/60 Hz 200 mA;  
Output: (i)6.5V 300 mA, (ii)7.5V 200 mA  
Phonebook with 250 entries  
Call log with 50 entries  
Talk time: 18 hours  
Standby time: 250 hours  
Note  
You can install a DSL (digital subscriber line) filter to  
prevent noise and caller ID problems caused by the  
DSL interference.  
You can find the Declaration of Conformity on  
Frequently asked questions  
No signal bar is displayed on the screen.  
I have chosen a wrong language which I cannot  
read, what do I do?  
No display  
Bad audio (crackles, echo, etc.)  
The handset is nearly out of range. Move it closer  
to the base station.  
The phone receives interference from the nearby  
electrical appliances. Move the base station away  
from them.  
The phone is at a location with thick walls. Move  
the base away from them.  
The handset is out of range. Move it closer to the  
base station.  
If the handset displays  
[Register your Handset], register your  
handset. (See the section on “Register additional  
handsets”).  
Make sure the batteries are charged.  
Make sure there are power and phone  
connections.  
1 Press  
2 Press  
3 Press  
to go back to the standby screen.  
to access the main menu screen.  
to select , then you see one of  
/
The handset on the charger does not charge.  
the following texts appear on the screen:  
Make sure the batteries are inserted correctly.  
Make sure the handset is placed properly on the  
charger.The LED at the back of the handset flashes  
once.  
Make sure the docking tone setting is turned on.  
When the handset is placed correctly on the  
charger, you can hear a docking tone.  
The charging contacts are dirty. Disconnect the  
power supply first and clean the contacts with a  
damp cloth.  
[Language]  
[Sprache]  
[Langue]  
[Lingua]  
If I fail to pair (register) the additional handsets to  
the base station, what do I do?  
The handset does not ring.  
Make sure the handset ringtone is turned on.  
The caller ID does not display.  
The service is not activated. Check with your  
service provider.  
The caller’s information is withheld or unavailable.  
4 Select it to access the language options.  
5 Select your own language.  
Your base memory is full. Press  
to select > [Unregister] to unregister the  
unused handsets and try again.  
.Then press  
/
My handset is in searching status, what do I do?  
Make sure that the base station has power supply.  
Register the handset to the base station.  
Move the handset closer to the base station.  
Batteries are defective. Purchase new ones with  
the same specifications.  
I cannot change the settings of my voice mail, what  
do I do?  
The voice mail service is managed by your service  
provider but not the phone itself. Contact your  
service provider to change the settings.  
For information, refer to the extended user  
documentation online.  
0168  
When this crossed-out wheeled bin symbol is  
attached to a product it means that the product is  
covered by the European Directive 2002/96/ EC.  
Reproduction in whole or in part is prohibited  
without the written consent of the copyright owner.  
Trademarks are the property of Koninklijke Philips  
Electronics N.V. or their respective owners.  
All rights reserved.  
UMS_M888  
05_EN_V1.0  
WK13285  
© 2013 Koninklijke Philips Electronics N.V.  

Yard Man 24A 020D401 User Manual
Yamaha CRW4260t B User Manual
Timex T433 User Manual
Targus netlink e340 User Manual
Sony Xplod CDX F7700 User Manual
Seagate MOMENTUS ST9750420AS User Manual
Scientific Atlanta AT8450 User Manual
Philips FM02FD02B User Manual
Pantech C150 User Manual
Nuance comm Dragon Naturallyspeaking V110 Premium K609A WN9 110 User Manual