Portable Stereo CD System
Operating Instructions
Model No. RX-D29
RX-D27
Dear customer
Thank you for purchasing this product.
Before connecting, operating or adjusting this product, please read these
instructions completely.
Please keep this manual for future reference.
These operating instructions fundamentally explain the operation of
RX-D29.
RQTT0585-P
PL
P PC
Supplied accessories
Table of contents
Please check and identify the supplied accessories.
Use numbers indicated when ordering replacements or optional accessories
from your Panasonic dealer.
IMPORTANT SAFETY INSTRUCTIONS ............................................ 2
Supplied accessories .......................................................................3
Maintenance ......................................................................................3
Power sources .................................................................................. 4
Concerning the remote control ....................................................... 4
Controls .............................................................................................5
Listening to radio broadcasts ................................... 6
Listening to CDs......................................................... 7
Playing MP3 RX-D29 only .......................................................... 8
Listening to tapes ...................................................... 8
Recording ................................................................... 9
Setting the time .......................................................... 9
Using the timers ....................................................... 10
3D sound with the Sound Virtualizer.............................................10
Sound quality .................................................................................. 10
Using headphones .......................................................................... 11
Audio software ................................................................................ 11
Limited Warranty (ONLY FOR U.S.A.)............................................ 11
Troubleshooting guide ................................................... Back cover
Specifications.................................................................. Back cover
In the U.S.A. to order accessories, refer to “Accessory Purchases”
on page 11.
AC power supply cord (polarized) (RJA0065-1D)....................... 1pc.
Remote control transmitter .......................................................... 1pc.
For RX-D29:(EUR648280)
For RX-D27:(EUR648278)
The model number and serial number of this product can be found on
either the back or the bottom of the unit.
Please note them in the space provided below and keep for future reference.
MODEL NUMBER
SERIAL NUMBER
User memo:
DATE OF PURCHASE
DEALER NAME
DEALER ADDRESS
TELEPHONE NUMBER
Product Service
Maintenance
Cleaning inside the deck
Clean the heads regularly to assure good quality playback and recording.
Use a cleaning tape (not included).
1. Damage requiring service —The unit should be serviced by
qualified service personnel if:
(a) The AC power supply cord or AC adaptor has been
damaged; or
(b) Objects or liquids have gotten into the unit; or
(c) The unit has been exposed to rain; or
(d) The unit does not operate normally or exhibits a marked change
in performance; or
(e) The unit has been dropped or the cabinet damaged.
2. Servicing—Do not attempt to service the unit beyond that described
in these operating instructions. Refer all other servicing to authorized
servicing personnel.
3. Replacement parts—When parts need replacing ensure the
servicer uses parts specified by the manufacturer or parts that have
the same characteristics as the original parts. Unauthorized
substitutes may result in fire, electric shock, or other hazards.
4. Safety check—After repairs or service, ask the servicer to perform
safety checks to confirm that the unit is in proper working condition.
Care of the CD lens
Clean the lens regularly to prevent malfunctions.
Use a blower to remove dust and a cotton swab if
it is extremely dirty.
Recommended product:
Lens cleaner kit (part no. SZZP1038C).
Lens
THE FOLLOWING APPLIES ONLY IN THE U.S.A.
Product information
CAUTION:
For product information or assistance with product operation:
In the U.S.A., refer to “Customer Services Directory” on page 11.
For assistance in the continental U.S.A. in obtaining repairs please
ship the product to:
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Panasonic Services Company - Customer Servicenter
Suite B 4900 George McVay Drive
McAllen, TX 78503
In Puerto Rico contact the Panasonic Sales Company.
Tel.(787) 750-4300
Fax.(787) 768-2910
When shipping the unit carefully pack and send it prepaid, adequately
insured and preferably in the original carton. Include a letter detailing
the complaint and provide a day time phone number where you can
be reached.
• Reorient or relocate the receiving antenna.
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD THE
PURCHASER WILL BE REQUIRED TO FURNISH A SALES
RECEIPT/PROOF OF PURCHASE INDICATING DATE OF
PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE.
CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT
RECEIVED WITHOUT SUCH PROOF OF PURCHASE.
Also, the purchaser will be responsible for shipping the unit to the
above address.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any unauthorized changes or modifications to this equipment would
void the user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
In Canada, contact the Panasonic Canada Inc. Customer Care Centre
authorized Servicentre closest to you.
3
RQTT0585
Power sources
The unit can be powered with household AC power or dry cell batteries (not included).
Insert memory batteries (not included) to save the current time, stored timer settings and radio stations.
Memory back-up
Using a household AC outlet
Using batteries (not included)
Insert batteries (not included) to save the current
time, timer settings and radio stations you have
set. If memory batteries are not used, memory
items are erased in the following situations:
• Power failures,
• The AC power supply cord is disconnected
from the power outlet,
Connect the AC power supply cord firmly to the
unit and the outlet.
The unit cannot be powered by batteries if the
AC power supply cord is connected.
Household AC outlet
(AC 120 V, 60 Hz)
•
The AC power supply cord is connected to the
unit while the unit is being powered by batteries.
These batteries do not power the unit.
AC power cord
(included)
Inner row
Outer row
(R14/LR14, C, UM-2)
(R6/LR6, AA, UM-3)
Note
When to change the batteries
The included AC power supply cord is for use
with this unit only. Do not use it with other
equipment.
When the battery indicator begins flashing,
replace all 6 of the batteries. It is also a good
idea to replace all the batteries before recording.
When to change the batteries
The batteries last about a year.
Connect the unit to AC power before replacing
the batteries.
Before connecting or disconnecting the AC
power supply cord, press [TAPE/OFF] and stop
the tape to turn the unit off. The memory
batteries are worn out faster if the cord is
disconnected with the power still on.
Note
Before playing starts the battery indicator may
flash although the batteries are not drained. It
appears correctly once you start play.
Removing the batteries
Open the battery cover and insert your finger in
the hole on the bottom of the unit and push out.
(Remove the power batteries first.)
For R14/LR14, C, UM-2
For R6/LR6, AA, UM-3
Concerning the remote control
Battery installation
Insert the batteries (not included) observing the correct polarities (
Correct method of use
,
).
(R6, AA, UM-3)
1
2
Remote control
signal sensor
2
Transmission window
About 7 meters in front
of the signal sensor
Operation notes
• Do not place obstacles between the remote control signal sensor and
the remote control unit.
• Do not expose the remote control signal sensor to direct sunlight or to
the bright light of fluorescent light.
• Take care to keep the remote control signal sensor and end of the
remote control unit free from dust.
To prevent damage
• Never place heavy items on it.
• Do not disassemble or reconstruct it.
• Do not spill water or other liquids into it.
4
RQTT0585
Controls
Main unit:
Remote control:
The functions of the buttons without descriptions are the
same as on the main unit.
Tape mode/standby switch (TAPE/OFF)
Press [TAPE/OFF] and stop the tape to turn the unit off.
The unit is in the standby condition when the AC power supply
cord is connected.
The primary circuit is always “live” as long as the power cord
is connected to an electrical outlet.
Tune mode select button (TUNE MODE)
CD lid
Tuner mode/band select/auto preset button
(TUNER/BAND –AUTO PRESET)
Timer set/check button
(TIMER SET/CHECK)
CD stop button (
Display
)
Sleep timer button
(SLEEP)
Clock display button
(DISPLAY)
Tuning/CD skip, search buttons (
,
)
Sound equalizer select button
(SOUND EQ)
CD play/pause button ( CD
)
CD Iid open/close
(
CD OPEN/CLOSE)
Volume control buttons
(VOLUME
,
)
Clock/timer adjust button
(CLOCK/TIMER ADJ)
Sound virtualizer button
(SOUND VIRTUALIZER)
1
4
7
2
5
8
0
3
6
Numbered buttons
9
CD play mode/FM mode
select button (PLAY MODE)
10
Program/clear button
(PGM/CLEAR)
Tuner mode/band select
button (TUNER/BAND)
Cassette deck
Record button (
)
Tape play button ( PLAY)
Rewind/review button (
REW/REV)
FF/CUE)
Fast-forward/cue button (
Normal tuning/CD skip,
search/clock, timer adjust
Remote control signal sensor (SENSOR)
buttons (
,
)
Standby/on indicator ( /I)
The indicator lights green when the unit is turned on.
When the AC power supply is used, it functions as an AC
connection indicator. (The indicator color changes to red
when the unit is turned off.)
RX-D29
Preset channel select/album
skip buttons (
ALBUM
)
RX-D27
Stop/eject button (
Pause button ( PAUSE)
STOP/EJECT)
Preset channel select buttons
PRESET TUNE
(
)
Speaker
These speakers do not have magnetic shielding. Do not place
them near televisions, personal computers or other devices
easily influenced by magnetism.
5
RQTT0585
Listening to radio broadcasts
Normal tuning
Preset tuning
Preset the stations (20 FM and 12 AM) to make tuning simpler.
2
1 3 4
2
1
RX-D29
2
3
1
Press [TUNER/BAND –AUTO PRESET] to select “FM” or
“AM”.
(Unit comes on.)
1
2
3
RX-D27
(Omit this step if using the remote control)
If “
” is on the display, press
Automatic presetting
[TUNE MODE] to clear it.
Do the following once each for FM and AM.
Preparations: Press [TUNER/BAND –AUTO PRESET] to select “FM” or
Press [– /
] or [
/ +] to tune
“AM”.
to the desired station.
Automatic tuning
Press and hold [TUNER/BAND –AUTO PRESET] on the main
unit until “AUTO” is displayed.
The tuner presets stations it can receive into the channels.
Press and hold [–/
] or [ /+] then release when the frequency
display starts to change. A station with good reception is automati-
cally selected and the process stops.
To stop automatic tuning, press [–/
] or [ /+] again.
Manual Presetting
Note
Remote control only
Presets one station at a time.
Automatic tuning may stop on a frequency where there is no station
if there is interference. Press [–/ ] and [ /+] to tune if this occurs.
Press [PGM/CLEAR].
1
Adjust the volume.
4
While “
seconds)
” is flashing (about 10
To improve reception
2
FM: Extend the whip antenna and adjust its direction.
AM: Adjust the position of the unit.
Press the numbered buttons to
select a channel.
If noise is excessive in the FM stereo mode
Press [PLAY MODE] on the remote control.
(“MONO” lights up.)
To select channel 10 or higher
>
e.g.12: [
=
10] → [1] → [2]
Sound will be produced in monaural, but this
also reduces noise.
Press the button again to cancel. (“MONO”
goes out.)
Repeat the above to preset other stations.
The station occupying a channel is erased if another station is preset in
that channel.
To listen to preset channels
Press [TUNER/BAND –AUTO PRESET] to select “FM” or
“AM”.
1
2
(Omit this step if using the remote control)
Press [TUNE MODE] to display
“
”.
3
Press [– /
] or [
/ +] to select
the desired channel.
(FM:1-20, AM:1-12)
Remote control:
Preset channel
[
/
ALBUM](
PRESET TUNE)
](PRESET TUNE
or [ALBUM
/
)
6
RQTT0585
Listening to CDs
Normal play
Program play
You can program up to 24 tracks.
3 1 2 4
2
3
1
Push [
CD OPEN/CLOSE] to
Remote control only
Ensure CD is stopped before programming.
1
open the CD lid and insert the CD.
Press [PGM/CLEAR].
1
Label must face upward.
Enter the track number with the numbered buttons.
2
To select a two digit number
>
e.g.16: [
=
10] → [1] → [6]
Push [
CD OPEN/CLOSE] to
2
3
To select a three digit number (MP3 only)
close the CD lid.
>
>
e.g.226: [=10] → [=10] → [2] → [2] → [6]
Press [CD
(Unit comes on.)
Play starts from the first track and
continues to the last track.
/
] to start play.
Elapsed play time
Program order
(MP3 only)
Program order
Specified track number
RX-D29 only
When playing MP3, “MP3” is displayed.
Track number in play
Specified track number
Adjust the volume.
4
Total play time of programmed tracks
Repeat step 2 until you have programmed all the tracks you want.
To stop play
Press [ ].
Press [CD
/
] .
While stopped, the number of tracks on the CD is displayed.
3
(MP3 only)
Total number of tracks
To cancel program play mode
Total playing time
Press [PGM/CLEAR] while stopped. “CLEAR” is displayed.
The mode is also canceled if the CD tray is opened.
This will also erase the entire program.
To check program contents
“P” appears in the display when play is stopped.
Total number of albums
] during playback.
Total number of tracks
Press [–/
] or [
/+] when “P” is displayed.
To check while programming press [DISPLAY] twice and after “P” appears,
To pause
Press [CD
/
press [–/
] or [
/+].
To resume, press [CD
/
].
Display
To search forward/
backward
Hold down [−/ ] (backward) or [ /+] (forward)
during playback or when paused.
You cannot search while playing MP3.
“— —:— —”: Program equals, or exceeds, 100 minutes but
programming and play are still possible.
24 tracks have already been programmed. The program is full.
“FULL”:
To skip forward/
backward
Press [−/ ] (backward) or [ /+] (forward)
during playback or when paused.
CD play modes
Remote control only
Display
You can repeat one track (
), all tracks (
) or play the tracks in
“NO DISC” is displayed if there is no disc in the unit.
random order (
).
Press [PLAY MODE] before or during playback to select the
desired mode.
Note
• If interference occurs to radios or televisions, place the unit as far as
possible from the equipment.
off (no indication)
• Do not push [ CD OPEN/CLOSE] during play, pause or immediately
after you inserted the CD and closed the CD lid. CD may be scratched.
RX-D29 only
When playing MP3, see page 8.
These modes remain active until the indicators are cleared.
You can use repeat mode with program play.
This unit can play CD-DA (digital audio) format audio CD-R and CD-
RW that have been finalized (a process that enables CD-R/CD-RW
players to play audio CD-R and CD-RW) upon completion of recording.
It may not be able to play some CD-R or CD-RW due to the condition
of the recording.
Note
• During play, you cannot select random play.
• Random and program play cannot be performed at the same time.
7
RQTT0585
Playing MP3
only
RX-D29
This unit can play MP3, a method of compressing audio without
overly hurting audio quality.
When creating MP3 files to play on this unit
Disc formats: ISO9660 level 1 and level 2 (except for extended formats)
CD-ROM drive
Naming tracks and albums
Prefix with 3-digit numbers in the
order you want to play
001album
1
001track.mp3
002track.mp3
003track.MP3
Extension
002album
001track.mp3
(or .MP3)
2
004track.mp3
005track.mp3
Starting play from an album (album skip)
004album
008track.MP3
009track.MP3
3
If you created an album such as
004album on the left, the files
may not play in name order.
The albums would play in the
Remote control only
Select the album with [
/
ALBUM] or [ALBUM
/
].
003album
4
006track.mp3
007track.MP3
order
1
,
2
,
3
,
4
.
Title names and album names are not displayable on this unit.
Playing only an album
Limitation on MP3
• This unit is compatible with multi-session but if there are a lot of
sessions it takes more time for play to start. Keep the number of
sessions to a minimum to avoid this.
Remote control only
You can play (
) or repeat play (
) tracks only in the
• This unit cannot play files recorded using packet write.
• If a CD-ROM format CD contains MP3 and files other than MP3,
only the MP3 files will be playable.
• Depending on how you create MP3 files, they may not play in the
order you numbered them or may not play at all.
selected album.
Press [PLAY MODE] before or during playback to select the
desired mode.
off (no indication)
• You can select another album with album skip.
• You cannot use random play with MP3.
Listening to tapes
This unit is suitable for playing normal tapes, but high and metal position
tapes will not be played to their full potential.
To stop play
Press [
/
STOP/EJECT]. (Unit is switched off.)
1 2 3 4
To pause
Press [ PAUSE ] during playback.
To resume, press [ PAUSE ].
To rewind/
fast-forward
Press [ REW/REV] (to rewind) or
[
FF/CUE ] (to fast-forward) in the stop mode.
To find a particular Press [ REW/REV] (to search backward) or
spot
[
FF/CUE] (to search forward) during
playback.
Play is resumed when the button is released.
Note
• The unit is on in the pause mode. Stop tape to turn the unit off by
Press [TAPE/OFF].
1
2
pressing [
/
STOP/EJECT ] when leaving the unit.
• Do not press [
PLAY] when rewinding or fast-forwarding, as this
Press [
/
STOP/EJECT ] to
Exposed tape facing
upward
may jam the tape.
Be sure to press [
open the deck and load a cassette.
Close deck by hand.
/
STOP/EJECT ] before the next operation.
• Tapes exceeding 100 minutes are thin and can break or get caught in
the mechanism.
• Tape slack can get caught up in the mechanism and should be taken
up before the tape is played.
• Endless tapes can get caught up in the deck’s moving parts if used
incorrectly.
• Sound quality may be effected and the cassette tape may become
stuck if you do not adhere to the following.
Side to be played
facing you
Press [
PLAY ] to start play.
Unit comes on and play starts.
3
4
- Do not use other stickers not included with the cassette tape.
- Place stickers on the cassette tape only as indicated.
Adjust the volume.
Full auto-stop
The automatic stop system will release the buttons when the tape reaches
the end during play, recording, fast-forwarding or rewinding.
8
RQTT0585
Recording
You can record radio broadcasts or CDs.
Before recording
• This unit is suitable for recording normal tapes, but it cannot record
onto high and metal position tapes to their full potential and prior
recordings will not be erased correctly.
To stop recording
Press [ STOP/EJECT ]. (The CD does not stop.)
/
To stop recording temporarily
Press [ PAUSE ]. (The CD does not stop.)
Press once again to resume recording.
• The recording level is set automatically.
• Take up the leader tape before proceeding.
To record on the other side of the cassette
Turn the cassette over and press [
].
Leader tape (Recording cannot be made.)
If the CD finishes before the cassette
1 3
Recording continues. Press [
/
STOP/EJECT ] to stop it.
If the cassette finishes before the CD
The CD continues playing. Press [ ] to stop it.
Erase protection
Use a screwdriver or similar object
Side A
to break out the tab.
Tab for side A
Adhesive tape
Tab for side B
To re-record on a protected cassette
Cover the hole with adhesive tape.
To erase a tape
1. Press [TAPE/OFF].
2. Insert the cassette with the side to be erased facing towards you and
the exposed tape facing up.
3. Press [
Press [
/
STOP/EJECT ] to
Exposed tape facing
upward
1
2
open the deck and load a cassette.
Close deck by hand.
].
[
PLAY ] is depressed at the same time.
Side to be recorded
facing you
Note
Select the source to be recorded.
When recording radio broadcasts
Tune in the station. (Perform steps 1–3 of “Normal tuning” on page 6.)
When recording CDs
Insert the CD to be recorded.
(Perform steps 1 and 2 of “Normal play” on page 7.)
• Noise may be recorded if this unit is near a TV. Keep the units at least
1.5 meters apart.
• Changes to volume and sound quality do not affect recording.
• To prevent interruptions to recording, make sure there is constant AC
power supply to the unit or replace the batteries.
• While recording you cannot perform the following operations.
- Switching play of the source (CD, Radio, Tape)
- Switching the radio AM/FM frequency
Press [CD
/
] and then [ ] to switch to CD mode.
If you want to record programmed tracks, program desired tracks
before proceeding to step 3.
- CD skipping, searching
Press [
] to start recording.
3
[
PLAY ] is also depressed with [
].
Recording starts (one side only).
The CD also starts playing if in CD mode.
Setting the time
1
Within 10 seconds
3
Press [– /
] or [
/ +] to set the
2 · 4
time.
Press and hold to change the time faster.
Remote control only
Press [CLOCK/TIMER ADJ].
3
4
To switch to clock display
Press [DISPLAY].
Clock display ←→ Current display
This is a 12-hour clock.
Press [TUNER/BAND –AUTO PRESET] to turn the unit on.
1
You can also use [CD
/
], [ PLAY] to turn the unit on.
Displaying the clock temporarily
Press [CLOCK/TIMER ADJ].
The clock is shown for about 10 seconds.
Remote control only
Note
Press [CLOCK/TIMER ADJ] once.
2
The clock is accurate to within 60 seconds a month.
Readjust if necessary.
9
RQTT0585
Using the timers (Remote control only)
To cancel the timer (when the unit is on)
Press [TIMER SET/CHECK] to clear the timer indicator from the display.
The timer comes on at the set time everyday if the timer is on.
5
To change the settings (when the unit is on)
To change the play times
1-3
4
Perform steps 1, 2, 3 and 5.
To change the source or volume
1. Press [TIMER SET/CHECK] to clear the timer indicator from the display.
If the settings are shown, press one more time.
2. Make changes to the source or volume.
3. Perform steps 4 and 5.
2 · 3
To check the settings (when the unit is off)
Press [TIMER SET/CHECK].
The settings are shown in the following order:
start time → finish time → source → volume → current time
Using the play timer
The play timer can be set to a certain time to wake you up.
Preparations:
You can enjoy other sources after you have set the timer.
Turn the unit off before the timer's start time.
• Turn the unit on and set the clock. (Perform the “Setting the time” steps
on page 9.)
• Prepare the music source you want to listen to and set the volume.
Note
If you turn the unit off and on again while a timer is functioning, the finish
time setting will not be activated.
Setting the start and finish times
Press [CLOCK/TIMER ADJ] to select “ PLAY ON”.
1
Clock
PLAY ON
PLAY OFF
Using the sleep timer
Previous display
Set the unit to stop and turn off after a certain time.
PLAY ON: to set the start time
PLAY OFF: to set the finish time
While enjoying the desired source
Press [SLEEP] to select the desired time (in minutes).
During “ PLAY ON” display
within approx. 10 seconds
30
60
90
120
OFF (off)
2
3
Press [– /
select the start time.
Press [CLOCK/TIMER ADJ].
] or [
/ +] to
To confirm the remaining time (when the unit is on)
Press [SLEEP].
During “ PLAY OFF” display
To change the setting
Press [SLEEP] to select the new setting.
Press [– /
select the finish time.
Press [CLOCK/TIMER ADJ].
] or [
/ +] to
Note
Turning the timer on
• The play and sleep timer can be used together.
• The sleep timer always has priority. Be sure not to overlap timer
settings.
Press [TIMER SET/CHECK] to
display “ PLAY”.
The settings are shown in the following order:
start time → finish time
4
5
Press [TAPE/OFF] and stop the tape to turn the unit off.
The unit must be off for the timer to operate.
If the unit is on, the timer will not function.
Play will start in the set condition at the set time.
3D sound with the Sound Virtualizer
Sound quality
You can choose one of four types of sound quality.
XBS:
Remote control only
Adds punch to rock
You can create a three-dimensional sound field when listening to stereo sound.
CLEAR: Clarifies higher sounds
SOFT: For background music
VOCAL: Adds gloss to vocals
Press [SOUND VIRTUALIZER]
to display “
Press again to cancel.
”.
Note
• Recordings are unaffected by this
feature.
Press [SOUND EQ] to select a setting.
• The actual effect depends on the
source played.
XBS
CLEAR
SOFT
VOCAL
EQ OFF (cancelled)
10
RQTT0585
Using headphones (not included)
Audio software
Take note of the following points to extend the life of your equipment.
Always read the instructions provided with the software.
Turn down the volume and connect the headphones to the
[PHONES] jack.
Plug type: 3.5 mm (1/8”) stereo
Discs
Choose discs with this mark:
Continued use of irregular shaped CDs
can damage the unit.
Do not
• use CDs that have extra labels or
stickers attached.
Carefully remove leftover adhesive
before use.
• attach scratch-proof covers or any other
kind of accessory.
• write anything on the CD.
• clean CDs with liquids. Wipe with a soft, dry cloth.
• use CDs printed with label printers available on the market.
• load a blank CD-R as it will cause abnormal malfunction and may
damage the CD-R.
Note
Avoid listening for prolonged periods of time to prevent hearing damage.
Limited Warranty (ONLY FOR U.S.A.)
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus, New Jersey 07094
Panasonic Sales Company, Division of Matsushita Electric
of Puerto Rico, Inc.,
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Panasonic Portable Audio Products Limited Warranty
Limited Warranty Coverage
IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD THE PURCHASER WILL BE
REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE
OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE
CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF
PURCHASE.
If your product does not work properly because of a defect in materials or workmanship,
Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred
to as “the warrantor”) will, for the length of the period indicated on the chart
below, which starts with the date of original purchase (“warranty period”), at its option either (a)
repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished
product. The decision to repair or replace will be made by the warrantor.
Limited Warranty Limits And Exclusions
This warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES
NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT
COVER damages which occurred in shipment, or failures which are caused by products not
supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect,
mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of
consumer controls, improper maintenance, power line surge, lightning damage, modification,
introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or
other business or rental use of the product, or service by anyone other than a Factory
Servicenter or other Authorized Servicer, or damage that is attributable to acts of God.
Product or Part Name
All Portable Audio Products
except item listed below
Parts
Labor
One (1) Year
One (1) Year
Rechargeable batteries (in
exchange for defective item)
Ten (10) Days
Not applicable
During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty
period, there will be no charge for parts. You must mail-in your product during the warranty
period. This Limited Warranty excludes both parts and labor for batteries, antennas, and
cosmetic parts (cabinet). This warranty only applies to products purchased and serviced in the
United States or Puerto Rico. This warranty is extended only to the original purchaser of a new
product which was not sold “as is”.
THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WAR-
RANTY COVERAGE”.
THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES
RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF
THIS WARRANTY. (As examples, this excludes damages for lost time, travel to and from the
servicer, loss of or damage to media or images, data or other memory or recorded content. The
items listed are not exclusive, but are for illustration only.)
Mail-In Service
For assistance in the continental U.S.A. in obtaining repairs please ship the product to:
Panasonic Services Company
Customer Servicenter
Suite B
4900 George McVay Drive
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MER-
CHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.
Some states do not allow the exclusion or limitation of incidental or consequential damages, or
limitations on how long an implied warranty lasts, so the exclusions may not apply to you.
This warranty gives you specific legal rights and you may also have other rights which vary from
state to state. If a problem with this product develops during or after the warranty period, you
may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then
write to the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.
McAllen, TX 78503
For assistance in Puerto Rico call Panasonic Sales Company (787)-750-4300 or
fax (787)-768-2910.
When shipping the unit carefully pack and send it prepaid, adequately insured and
preferably in the original carton. Include a letter detailing the complaint and provide a day time
phone number where you can be reached.
PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE
YOUR RESPONSIBILITY.
Customer Services Directory
Obtain Product Information and Operating Assistance; locate your
nearest Dealer or Servicenter; purchase Parts and Accessories; or
make Customer Service and Literature requests by visiting our Web
Site at:
Accessory Purchases
Purchase Parts, Accessories and Instruction Books online for all
Panasonic Products by visiting our Web Site at:
or, send your request by E-mail to:
or, contact us via the web at:
You may also contact us directly at:
You may also contact us directly at:
1-800-211-PANA (7262),
Monday-Friday 9 am-9 pm; Saturday-Sunday 10 am-7 pm, EST.
1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only) (Monday – Friday 9 am to 8 pm, EST.)
Panasonic Services Company
20421 84th Avenue South, Kent, WA 98032
(We Accept Visa, MasterCard, Discover Card, American Express, and Personal Checks)
For hearing or speech impaired TTY users, TTY: 1-877-833-8855
For hearing or speech impaired TTY users, TTY: 1-866-605-1277
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/Factory
Servicenter:
Ave. 65 de Infantería, Km. 9.5, San Gabriel Industrial Park, Carolina, Puerto Rico 00985
Phone (787)750-4300, Fax (787)768-2910
11
RQTT0585
Troubleshooting guide
Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the
chart do not solve the problem, refer to the “Customer Services Directory” on page 11 if you reside in the U.S.A., or refer to the “Product
information” on page 3 if you reside in Canada.
Reference pages are shown as black circled numbers
.
4
Common Problems
The unit doesn’t work on batteries.
Is the AC power supply cord connected to the unit? Disconnect when using batteries.
Have the batteries been inserted correctly? Check that the poles (+ and –) are correctly aligned.
Replace the batteries or use household AC power.
4
“UO1” is displayed.
CD
“ERROR” is displayed.
Play doesn’t start or display is incorrect.
Indicates an incorrect operation. Read the instructions.
Clean the CD.
Wait for an hour for condensation to dry, then try again.
Make sure the label is facing up.
Replace the CD if it is scratched, warped, or irregularly shaped.
only
RX-D29
Play of a multi-session disc may not be possible if there is a blank data segment between sessions.
only
RX-D29
If there is large JPEG data etc. within a MP3 file, sound may become muted and play may not be possible.
only
RX-D29
If you try playing a CD that contains MP3 format data and normal audio data (CD-DA), output from
one of the above may become silent, and play may not be possible.
CD-RW cannot be read.
The disc was incompletely formatted. Use the recording equipment to fully format the disc before recording.
Cassette
Recording not possible.
Has the cassette’s tab been removed? Cover the hole with adhesive tape.
9
Clean the heads.
Poor sound quality.
3
The batteries are flat. Replace the batteries or connect to household AC power.
Press [ PLAY] then [ STOP/EJECT].
The cassette cannot be ejected or the lid can’t
be closed when loading a cassette.
/
Radio
A lot of noise.
Is another remote control being used? Use it further away from this unit.
Is a TV on? Move the unit away from the TV or turn it off.
Remote control
The remote control doesn’t work.
Check the batteries are inserted correctly.
Replace the batteries if they are worn.
4
Specifications
Frequency range
Power requirement
AC
FM
87.5–108.0 MHz (100 kHz steps)
120 V, 60 Hz
Power consumption: (RX-D29) 14 W
(RX-D27) 10 W
AM
520–1710 kHz (10 kHz steps)
44.1 kHz
16 bit linear
Semiconductor laser (wavelength 780 nm)
2 channel, stereo
Sampling frequency
Decoding
Battery
9 V (Six R14/LR14, C, UM-2 batteries)
• Do not use rechargeable type batteries.
4.5 V (Three R6/LR6, AA, UM-3 batteries)
• Do not use rechargeable type batteries.
408 x 163 x 273 mm
Beam source
No. of channels
Wow and flutter
D/A converter
Track system
Monitor system
Recording system
Erasing system
Frequency range
Normal position
Speakers
Memory back-up
Dimensions (WxHxD)
Less than possible measurement data
1 bit DAC
(16 1/16" x 6 7/16" x 10 3/4")
4 track, 2 channel, stereo
Variable sound monitor
AC bias
Mass
(RX-D29) 3.5 kg (7 Ib. 12.5 oz.) without batteries
(RX-D27) 3.3 kg (7 Ib. 5.5 oz.) without batteries
Multi Pole magnet
50–12000 Hz
Power consumption in standby mode:
(RX-D29) 2.3 W
(RX-D27) 1.1 W
Full range
(RX-D29) 8 cm (3 3/20") 3 Ω x 2
(RX-D27) 8 cm (3 3/20") 4 Ω x 2
1.5 cm (19/32") 1 kΩ x 2
Tweeter (RX-D29 only)
Note
Jacks
Output
PHONES: 3.5 mm stereo (32 Ω)
Specifications are subject to change without notice.
Mass and dimensions are approximate.
Panasonic Consumer Electronics
Company, Division of Matsushita
Electric Corporation of America
One Panasonic Way Secaucus,
New Jersey 07094
Panasonic Sales Company,
Panasonic Canada Inc.
5770 Ambler Drive
Mississauga, Ontario
L4W 2T3
En
Division of Matsushita Electric of
Puerto Rico, Inc. (“PSC”)
Ave. 65 de Infantería, Km. 9.5
San Gabriel Industrial Park, Carolina,
Puerto Rico 00985
RQTT0585-P
© 2004 Matsushita Electric Industrial Co., Ltd.
Printed in China
M0204YS0
|