WARNING
TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
THIS APPLIANCE SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING WATER AND
THAT NO OBJECT FILLED WITH LIQUIDS SUCH AS VASES SHALL BE PLACED ON
APPARATUS.
CAUTION
iPod iPhone Clock Radio W/ FM Receiver
And Dual Alarm Clock
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Warning: To reduce the rise of
The exclamation point within
The lightning flash with
arrowhead symbol, within an
equilateral triangle, is
intended to alert the user to
the presence of uninsulated
“dangerous voltage” within
the products enclosure that
Model : PICL34
electric shock, do not remove
an equilateral triangle is
cover
(or
back)
no
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
user-serviceable parts inside.
Refer servicing to qualified service
personnel.
may
be
of
sufficient
magnitude to constitute a risk
of electric shock to persons.
IMPORTANT SAFETY INSTRUCTIONS
1)
2)
3)
4)
5)
6)
7)
8)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9)
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong are provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Note: Please read and follow these instructions before using your unit.
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
- 1 -
CONNECTING THE UNIT TO POWER
LOCATION OF CONTROLS
Plug one end of the AC/DC adaptor into the DC-In jack, and then plug the other end into AC wall outlet.
Before switching on the unit, make sure that the voltage of your electricity supply is the same as that
indicated on the rating plate.
Back-up Battery
Open the battery door located at the bottom of the unit, insert 2 pcs. ‘AA’ size (UM-3) batteries with
battery polarities same as shown inside the battery compartment.
In case of AC power outage or interrupted AC power, the current time, alarm time settings and the
stored radio stations are preserved in the memory of the unit.
Important: When the unit is not use for 3 days or more and also the unit is not connect to AC power
during that time, please remove the battery to avoid damage to the set from leakage of battery.
SETTING THE TIME
Before starting to set the time, make sure that the unit is in POWER OFF Mode.
If you have IPhone or iPod (Except iPod Shuffle)
1. Dock in the iPhone/iPod on the 30 pins Connector
2. Press the SNOOZE/SLEEP button for a few seconds until the display shows SYN, and the unit is
automatically synchronized the time same as the iPod/iPhone.
If you do not have any iPhone/iPod units
1. Press and hold the FUNC/CL ADJ button for a few seconds, the hour digit in the display will start
flashing.
2. Press the SKIP UP/TUNE+ or SKIP DOWN/TUNE- button to adjust the hour.
3. When the correct hour is selected, press the FUNC/CL.ADJ. button again to enter the minute mode
with minute digit flashing.
4. Press the SKIP UP/TUNE+ or SKIP-/TUNE- button to adjust the minute.
5. When the correct time is selected, press the FUNC/CL ADJ. button to store the time in the memory.
SETTING THE ALARM TIME
1
2
IPod/iPhone Connector
Display
11
12
13
14
15
16
17
PLAY/PAUSE [/] / MEM Button
Volume+ Button
Before starting to set the alarm time, make sure that the unit is in POWER OFF mode.
1. Press the AL1 or AL2 button once and the AL1 or AL2 icon will appear in the display.
2. Press the FUNC/CL. ADJ. button to select the alarm wake up source. You can choose buzzer,
iPod/iPhone, or Radio.
3
Speaker
Snooze / Sleep Button
Volume- Button
4
Skip Down [ ] / Tun- Button
Alarm 1 Button
5
Battery Compartment
FM Antenna
3. Press and hold the AL1 or AL2 button for a few seconds, the alarm hour digit will begin flashing.
4. Press the /TUNE+ or /TUNE- button to adjust the alarm hour.
5. When the desired alarm hour is selected, press the AL1 or AL2 button again, the alarm minute digit
will begin flashing.
6
Function/Clock Adjust Button
Power/Alarm Off Button
Skip Up [ ] / Tune+ Button
Alarm2 Button
7
DC In Jack
8
9
6. Press the /TUNE+ or /TUNE- button to adjust the alarm minute.
7. When the desired alarm time is selected, press the AL1 or /AL2 button again to confirm.
Note : If you choose iPod/iPhone as the alarm wake up source, please make sure that you have the
iPod/iPhone in place.
10
Color Button
TURN OFF THE ALARM
When the alarm activate, press the POWER/AL.OFF button to turn off the alarm.
- 5 -
- 4 -
SNOOZE FUNCTION
Charging your iPod
1. Whenever the alarm activates, it can be temporarily suspended for a short period of 10
minutes by pressing the SNOOZE/SLEEP button.
2. The alarm will then automatically activate again after the 10 minutes SNOOZE period has
ended.
While your iPhone or iPod is docked in the unit and the unit is connected to AC power, your iPhone or
iPod will recharge until your iPhone or iPod is fully charged.
AUX-IN CONNECTION
3. This procedure can be repeated for up to approximately one hour.
1. Press the POWER/AL OFF button to turn on the unit.
2. Press the FUNC/CL.ADJ. button to select the Aux mode.
3. Insert one side of the audio cable into the Line-Out or Phone Jack on your MP3 Player or audio
device and the other side into the AUX-IN jack of the unit.
RADIO OPERATION
1. Press the POWER/AL OFF button to turn on the unit.
2. Press the FUNC/CL.ADJ. button to select the FM Radio mode.
3. Press and hold the /TUNE+ or /TUNE- for approx. 1 second, it will start to search the
next radio station in the direction of the search. The search operation simply finds stations
with strong signals. Stations with weak signal can only be tuned in manually.
4. Press VOLUME+ or VOLUME- button to adjust the volume to the desired listening level.
4. Turn on your MP3 player or audio device and follow its playback instructions.
SLEEP TO MUSIC FUNCTION
1. This function allows you to listen to the radio, iPhone/iPod or any audio device that connected to the
aux-in jack of the unit while you fall asleep.
SAVING RADIO STATIONS IN THE MEMORY
2. Press the SNOOZE/SLEEP button, the display will show the default sleep time of 90 minutes. Press
the SNOOZE/SLEEP button again to select the sleep time with decrement of 10 minutes.
3. When the correct sleep time is selected, stop pressing the SNOOZE/SLEEP button, the unit will go
to the sleep mode in about 5 seconds with the SLEEP icon appear in the display.
4. Now you can enjoy listening to the selected music for the pre-set period of sleep time.
5. After this pre-set time has elapsed, the unit will switch off automatically.
Note : If you choose Aux-in for the Sleep Function, when the pre-set time has elapsed, only the unit will
turn off, the audio device that connected to the aux-in jack is still in working.
Note : If you use this unit in the first time, or after plug off the AC/DC adaptor from a wall outlet,
the unit memory number will be starting from P01.
1. Tune to the desired stations.
2. Press and hold the PLAY/PAUSE/MEMORY button, the display will show the next memory
station number and flashing.
3. Press the /TUNE+ or /TUNE- button to select memory number, then press
PLAY/PAUSE/MEMORY button again to store the station into the memory.
4. Repeat step 1 to 3 to store more radio stations in the memory.
5. Up to maximum 20 radio stations can be stored in the memory.
CHANGING DISPLAY COLOR
Press the COLOR button to turn on the color display changing. The display color will change from one
TO SELECT A STORED RADIO STATION IN THE MEMORY
In RADIO mode, use the AL1 or AL2 button to select the stored radio station.
Press the AL1 button will go to the next stored radio station.
Press the AL2 button will go to the last stored radio station.
color to another color every few seconds. Press the COLOR button again set the display to only one
color.
SPECIFICATIONS
LISTEN TO iPOD/iPHONE WITH DOCKING CONNECTOR
Frequency Range:
FM 88 – 108 MHz
Warning : Turn off your iPhone/iPod before docking on the unit
1. Press the POWER/AL OFF button to turn on the unit.
Power Supply:
AC 100V to 240V ~ 50/60Hz
DC Adaptor : 7.5V – 1.8A
2. Press the FUNC/CL.ADJ. button to select the iPhone/iPod mode.
3. Connect the iPhone or iPod to the docking connector, the iPhone or iPod will start playing.
4. Press the VOLUME+ or VOLUME- button to your desired listening level.
5. During playing or in pause mode, press the /TUNE+ button to go to the next track.
6. During playing, press the /TUNE- button once to go back to the beginning of the track.
Press the /TUNE- button twice to go back to the previous track.
Specifications are subject to change without further notice.
7. In pause mode, press the /TUNE- button once to go back to the previous track.
8. During playing, press the PLAY/PAUSE/MEMORY button to temporarily pause playing. To
resume, press the PLAY/PAUSE/MEMORY button again.
Warning : Please make sure that your iPhone or iPod is properly docked into the unit. Failure to
do so may damage your iPhone/iPod.
- 6 -
- 7 -
|