Contents
Important Safety Instructions
2
Precations
3
5
Super Audio CD / CD Player
C-S5VL
Instruction Manual
Features
Before Using This Product
Connecting to Other Devices
Disc Playback
6
14
17
Available Actions During Playback 20
Playback Methods
Setup
23
27
30
33
Thank you for purchasing an Onkyo C-S5VL Super
Audio CD / CD Player.
Please read this manual thoroughly before making
connections and plugging in the unit.
Troubleshooting
Specifications
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new C-S5VL.
Please retain this manual for future reference.
En
Precautions
1. Recording Copyright—Unless it’s for personal use
only, recording copyrighted material is illegal without the
permission of the copyright holder.
2. AC Fuse—The AC fuse inside the unit is not
userserviceable. If you cannot turn on the unit, contact
your Onkyo dealer.
9. Installing this Unit
•
•
Install this unit in a well-ventilated location.
Ensure that there’s adequate ventilation all around
this unit, especially if it’s installed in an audio rack.
If the ventilation is inadequate, the unit may
overheat, leading to malfunction.
•
•
•
•
Do not expose this unit to direct sunlight or heat
sources, because its internal temperature may rise,
shortening the life of the optical pickup.
Avoid damp and dusty places, and places subject to
vibrations from loudspeakers. Never put the unit on
top of, or directly above a loudspeaker.
Install this unit horizontally. Never use it on its side
or on a sloping surface, because it may cause a
malfunction.
If you install this unit near a TV, radio, or VCR, the
picture and sound quality may be affected. If this
occurs, move this unit away from the TV, radio, or
VCR.
3. Care—Occasionally you should dust the unit all over
with a soft cloth. For stubborn stains, use a soft cloth
dampened with a weak solution of mild detergent and
water. Dry the unit immediately afterwards with a clean
cloth. Don’t use abrasive cloths, thinners, alcohol, or other
chemical solvents, because they may damage the finish or
remove the panel lettering.
4. Power
WARNING
BEFORE PLUGGING IN THE UNIT FOR THE FIRST
TIME, READ THE FOLLOWING SECTION
CAREFULLY.
AC outlet voltages vary from country to country. Make
sure that the voltage in your area meets the voltage
requirements printed on the unit’s rear panel (e.g., AC 120
V, 60 Hz or AC 100-240 V, 50/60 Hz).
The power cord plug is used to disconnect this unit from
the AC power source. Make sure that the plug is readily
operable (easily accessible) at all times.
Pressing the [POWER] button to select OFF mode does
not fully shutdown the unit. If you do not intend to use the
unit for an extended period, remove the power cord from
the AC outlet.
10. Moisture Condensation
Moisture condensation may damage this unit.
Read the following carefully:
Moisture may condense on the lens of the optical pickup,
one of the most important parts inside this unit.
•
Moisture condensation can occur in the following
situations:
-
-
-
-
The unit is moved from a cold place to a warm
place.
A heater is turned on, or cold air from an air
conditioner is hitting the unit.
In the summer, when this unit is moved from an
air conditioned room to a hot and humid place.
The unit is used in a humid place.
5. Preventing Hearing Loss
Caution
Excessive sound pressure from earphones and headphones
can cause hearing loss.
•
Do not use this unit when there’s the possibility of
moisture condensation occurring. Doing so may
damage your discs and certain parts inside this unit.
6. Batteries and Heat Exposure
Warning
Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat as sunshine, fire or the like.
7. Never Touch this Unit with Wet Hands—Never
handle this unit or its power cord while your hands are wet
or damp. If water or any other liquid gets inside this unit,
have it checked by your Onkyo dealer.
If condensation does occur, remove all discs and leave this
unit turned on for two to three hours. By this time, the unit
will have warmed up and any condensation will have
evaporated.
8. Handling Notes
•
If you need to transport this unit, use the original
packaging to pack it how it was when you originally
bought it.
Do not leave rubber or plastic items on this unit for a
long time, because they may leave marks on the
case.
•
•
•
This unit’s top and rear panels may get warm after
prolonged use. This is normal.
If you do not use this unit for a long time, it may not
work properly the next time you turn it on, so be sure
to use it occasionally.
When you’ve finished using this unit, remove all
discs and turn off the power.
•
3
Precautions—Continued
This unit contains a semiconductor laser system and is
classified as a “CLASS 1 LASER PRODUCT”. So, to use
this model properly, read this Instruction Manual carefully. In
case of any trouble, please contact the store where you
purchased the unit.
To prevent being exposed to the laser beam, do not try to open
the enclosure.
For Canadian Models
NOTE: THIS CLASS B DIGITAL APPARATUS
COMPLIES WITH CANADIAN ICES-003.
For models having a power cord with a polarized plug:
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH
WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
CAUTION:
Modèle pour les Canadien
CLASS 1M VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY
WITH OPTICAL INSTRUMENTS.
REMARQUE: CET APPAREIL NUMÉRIQUE DE LA
CLASSE B EST CONFORME À LA NORME NMB-003
DU CANADA.
THIS PRODUCT UTILIZES A LASER. USE OF
CONTROLS OR ADJUSTMENTS OR PERFORMANCE
OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE.
Sur les modèles dont la fiche est polarisée:
ATTENTION: POUR ÉVITER LES CHOCS
ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS
LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
The label on the right is applied on the rear panel.
1. This unit is a CLASS 1 LASER
PRODUCT and employs a laser
inside the cabinet.
For British models
Replacement and mounting of an AC plug on the power
supply cord of this unit should be performed only by qualified
service personnel.
2. To prevent the laser from being
exposed, do not remove the
cover. Refer servicing to
IMPORTANT
The wires in the mains lead are coloured in accordance with
the following code:
qualified personnel.
For U.S. models
Blue:Neutral
Brown:Live
FCC Information for User
As the colours of the wires in the mains lead of this apparatus
may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
CAUTION:
The user changes or modifications not expressly approved by
the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation.
IMPORTANT
The plug is fitted with an appropriate fuse. If the fuse needs to
be replaced, the replacement fuse must be approved by ASTA
or BSI to BS1362 and have the same ampere rating as that
indicated on the plug. Check for the ASTA mark or the BSI
mark on the body of the fuse. If the power cord’s plug is not
suitable for your socket outlets, cut it off and fit a suitable
plug. Fit a suitable fuse in the plug.
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
For European Models
Declaration of Conformity
We,
ONKYO EUROPE
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
ELECTRONICS GmbH
LIEGNITZERSTRASSE 6,
82194 GROEBENZELL,
GERMANY
-
-
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
declare in own responsibility, that the ONKYO product
described in this instruction manual is in compliance with the
corresponding
technical standards such as EN60065,
EN55013, EN55020 and EN61000-3-2, -3-3.
GROEBENZELL, GERMANY
K. MIYAGI
ONKYO EUROPE ELECTRONICS GmbH
4
Features
- Exclusive Onkyo VLSC Technology
- High-Grade Wolfson 192 kHz / 24-Bit D/A
Converter (WM8742)
- Crystal Oscillator Thermal Regulation / Jitter
Cleaner Circuitry to Stabilize Clock Frequency
- Super Audio CD / Audio CD / CD-R / CD-RW /
MP3 CD / WMA CD Playback Capability
- Digital Out On/Off
- Digital Filter Control (CD:5Modes / Super Audio
CD:4 Modes and DSD Direct)
- Phase Control (Normal / Invert)
- Headphone Jack with Volume Control
- Repeat Modes (Super Audio CD / CD ; Disc Repeat
/Track Repeat, MP3 CD / WMA CD ; Track Repeat/
Folder Repeat/ Disc Repeat)
- Random Modes (Super Audio CD / CD ; Disc
Random,MP3 CD / WMA CD ; Folder Random/
Disc Random)
- 19 mm (3/4")-pitch Audio Terminals for High-
Grade Cable
- 2 Digital Outputs (Optical / Coaxial)
- 4-Mode Display Dimmer (Standard -> Dimmer ->
Dim -> Off)
- Hi-Rigidity, Anti-Resonant Flat Chassis
- Heavy-Duty Inlet Power Cord
- Aluminum Front Panel
- RI-Compatible Remote Control
Table of Contents
Important Safety Instructions................................2
Precautions...............................................................3
Features....................................................................5
Change the Displayed Information......................22
Playback Methods .................................................23
Repeat (Loop) ......................................................23
A-B Repeat (Loop between Two Points).............23
Random (Shuffle) ................................................23
Memory Playback................................................24
Before Using This Product......................................6
Check the Supplied Accessories............................6
Getting the Remote Controller Ready...................6
Names of Each Part ...............................................7
Using the Remote Controller............................... 11
Supported CD Types............................................12
Limitations on Playback of MP3
and WMA Files ...................................................12
Handling Discs ....................................................13
Condensation.......................................................13
Setup .......................................................................27
Setup Menu List...................................................27
Available Settings ................................................27
Making Settings...................................................29
Troubleshooting .....................................................30
Returning Settings to the Defaults.......................30
Power ...................................................................30
Disc Playback ......................................................30
Playing Music CDs with Copy Control
Functions..............................................................31
Connecting to Other Devices................................14
Analog Connections ............................................14
Digital Connections.............................................14
Audio ...................................................................31
Remote Controller ...............................................31
Devices..........................................................32
Connecting to
Connecting the Power Cord.................................16
Capable Components ............15
Disc Playback.........................................................17
CD And Super Audio CD Playback....................17
MP3 and WMA Playback....................................18
Specifications..........................................................33
Available Actions During Playback.....................20
Stop Playback ......................................................20
Pause Playback....................................................20
Fast Reverse/Fast Forward ..................................20
Select Tracks........................................................20
Specify a Track (CD or Super Audio CD) ..........20
Play a Specific Location on a Track....................21
Select Folders and Tracks....................................21
Eject the Disc.......................................................22
5
Before Using This Product
This section describes things to check and important information to know before using this product.
Check the Supplied Accessories
After opening the package, make sure that all the supplied accessories are included.
- Remote controller (RC-749C)[1]
- AA (R6) batteries.................. [2]
(Not supplied with products for
China.)
- Audio connection
cable (1 m / 3.3ft)................. [1]
-
cord ዄ0.8 m / 2.6ft) ......[1]
- Power cord (2 m / 6.5ft)........[1]
(The shape differs depending on
region.)
Getting the Remote Controller Ready
Press in the direction of the arrow and lift to
remove the cover.
Close the cover.
If the remote controller becomes unresponsive, replace
the batteries with two new dry-cell batteries (AA).
- Be sure to insert the batteries correctly, in line with
the charge symbols ( and ).
- Avoid mixing new batteries with old batteries, or
mixing battery types.
Insert the two supplied batteries, making sure
to line up the plus and minus ends of the
batteries with the symbols in the battery
compartment.
(The battery is not supplied with products for
China.)
- If you will not be using the remote controller for a
prolonged period, remove the batteries in order to
prevent corrosion.
6
Before Using This Product—Continued
Names of Each Part
Front Panel
POWER button
This button is used to turn the unit on and off.
Notes
If the brightness is set to "Off," operating the unit will cause it to
illuminate for five seconds.
Disc tray
Insert discs into this tray. (See p.17)
DISPLAY button
button
Use this button to change the displayed
information. (See p.22)
Open and close the disc tray. (See p.17)
DIGITAL OUT indicator
Illuminates when digital output is on.
DIGITAL OUT button
Use this button to turn digital output on and off.
(See p.17)
Display (See p.9)
button
Use this button to skip to the beginning of the track
being played. Press and hold down to fast reverse.
(See p.20)
If a disc containing MP3 or WMA tracks is
stopped, this switches folders. If a CD or Super
Audio CD is stopped, this selects the previous
track.
Notes
This button cannot be used during playback.
Remote control sensor
CD button
Select the CD area to play a Super Audio CD
hybrid disc. (See p.18)
button
Use this button to skip to the beginning of the next
track. Press and hold down to fast forward. (See
p.20)
If a disc containing MP3 or WMA tracks is
stopped, this switches folders. If a CD or Super
Audio CD is stopped, this selects the next track.
Notes
This button cannot be used during playback.
button
SA-CD button
Select the Super Audio CD area to play a Super
Audio CD hybrid disc. (See p.18)
Use this button to pause disc playback. (See p.20)
When paused, this resumes playback.
button
Notes
Use this button to stop disc playback. (See p.20)
button
This button cannot be used during playback.
Use this button to play the disc. (See p.17)
PHONES jack
Stereo headphones with a standard plug can be
plugged into this jack.
DIMMER button
Use this button to select one of four display-
brightness levels.
PHONES LEVEL control
Use this control to adjust the volume of the
headphones connected to the unit. Turn the control
right to increase the volume, and left to lower it.
7
Before Using This Product—Continued
Rear Panel
AUDIO OUTPUT ANALOG
AUDIO OUTPUT DIGITAL (OPTICAL/
COAXIAL)
Connect the analog audio in terminal of an
amplifier or similar to this terminal, using the
supplied audio cable.
Connect an amplifier or similar with a digital in
terminal to this terminal. Connect components to
the optical terminal using a commercial optical
digital cable for audio. Connect components to the
coaxial terminal using a commercial coaxial digital
cable. The same digital audio is output from the
optical and coaxial terminals.
jack
Connect an Onkyo amplifier or similar with an
terminal to this jack.
AC INLET
The supplied power cord should be connected
here.
See pages 14-16 for hookup information.
8
Before Using This Product—Continued
Display
MEMORY
Displayed during playback.
Displayed during memory playback. (See p.24)
MP3
Displayed when playback is paused.
Displayed when a disc containing MP3 tracks is
played.
FOLDER
Displayed together with the folder number when a
disc containing MP3 or WMA tracks is played.
WMA
Displayed when a disc containing WMA tracks is
played.
TRACK
Displayed together with the track number when a
disc is played.
Number display
Displays the folder number, track number, playing
time, remaining time, and the like.
TOTAL
Displayed when the total and remaining time of the
track are shown.
A-B
Displayed during A-B repeat playback. (See p.23)
TRACK
FOLDER
Displayed together with the track number when a
disc containing MP3 or WMA tracks is played.
Displayed during repeat playback and random
playback of a folder. (See p.23)
REMAIN
RANDOM
Displayed when the remaining time of the track is
shown.
Displayed during random playback. (See p.23)
Displayed during repeat playback.
"1" is shown when only the currently playing track
is repeated. (See p.23)
9
Before Using This Product—Continued
Remote controller
OPEN/CLOSE buttons
Open and close the disc tray. (See p.17)
DISPLAY button
Use this button to change the information on the
unit's display. (See p.22)
DIMMER button
Use this button to select one of the unit's four
display-brightness levels.
Notes
If the brightness is set to "Off," operating the unit will cause it to
illuminate for five seconds.
SA-CD/CD button
Select the playback area (Super Audio CD/CD) to
play on a Super Audio CD hybrid disc. (See p.18)
Notes
The mode cannot be switched during playback.
SETUP button
Use this button to begin or end unit setup. (See
p.29)
Number keys
Use these keys to select tracks and the like. (See
p.20 and p.24)
FOLDER / buttons
This is used to select folders on discs containing
MP3 or WMA tracks. (See p.21)
Change the setting item during setup. (See p.29)
TRACK / buttons
This is used to select tracks. To play the selected
track, press the Play button or the ENTER button.
(See p.21)
Change the setting during setup. (See p.29)
CLR button
Use this button to clear any numbers that have
been entered during numeric input.
When making a memory setting, the selected track
is erased.
SEARCH button
Specify the track on a music CD or SACD.
Search for a folder on a CD containing MP3 or
WMA tracks. (See p.21)
MEMORY button
Use this button to begin or end memory playback.
(See p.24)
10
Before Using This Product—Continued
A-B button
Using the Remote Controller
Use this button to set the start and end positions for
A-B repeat. (See p.23)
Point the remote controller toward the remote control
sensor, within the field shown in the drawing.
ENTER button
Finalize your selection.
RANDOM button
Press this button for random playback. (See p.23)
REPEAT button
Press this button for repeat playback. (See p.23)
button
Use this button to pause playback. When paused,
this resumes playback. (See p.20)
Approx.5m
(16 feet)
button
Use this button to skip to the beginning of the track
being played. (See p.20)
- Do not expose the remote control sensor to strong
light, such as direct sunlight or inverted fluorescent
light.
- Using the unit near equipment that emits infrared
beams or with another remote controller may cause
malfunctions.
- Make sure that the audio rack does not have colored
glass, as this could prevent the remote controller
from functioning properly.
- The remote controller will not function if there are
obstacles between it and the remote control sensor.
- Do not place objects such as books on top of the
remote controller. Doing so could depress the
buttons on the remote continually and drain the
batteries.
button
Use this button to play the disc. (See p.17)
button
Use this button to skip to the beginning of the next
track. (See p.20)
button
Use this button to fast reverse. (See p.20)
button
Use this button to stop disc playback. (See p.20)
button
Use this button to fast forward. (See p.20)
VOLUME button
When using this unit in combination with an
Onkyo pre-main amplifer (integrated amplifier),
adjust the playback volume by controlling the
amplifier.
Notes
-
-
Some pre-main amplifers are not supported.
When operating the pre-main amplifer, point the remote
controller at the amplifier's sensor.
MUTING button
When using this unit in combination with an
Onkyo pre-main amplifer, temporarily lower the
volume using the amplifier. Press it again to return
to the previous volume.
Notes
-
-
Some pre-main amplifers are not supported.
When operating the pre-main amplifer, point the remote
controller at the amplifier's sensor.
11
Before Using This Product—Continued
Supported CD Types
Limitations on Playback of MP3 and
WMA Files
Discs with the following logos on their labels can be
played back.
- Use discs recorded using the ISO 9660 Level 1 or 2
file system, and the extended format (Joliet). (The
supported directory depth, however, is the same as
ISO 9660 Level 1 (8).)
Discs recorded using a hierarchical file system
(HFS) cannot be played.
- Up to 255 folders, and up to 255 tracks per folder
can be recognized and played back.
- Folders and tracks are displayed on the screen as
three-digit numbers.
- Only the first session of multi-session discs can be
played back.
- If an unsupported disc is played back, the unit's
display appears as follows:
Disc
Logo
File Format/File Type
PCM
Type
Audio
CD
Super
Audio
CD
DSD
CD-R
Audio CD, MP3, WMA
MP3, WMA
CD-RW
Audio CD, MP3, WMA
- Make sure that the disc is finalized.
Caution
!
MP3, WMA
-
Some discs recorded using a recorder or computer cannot
be played back. (Possible causes: disc characteristics,
scratches, soiling, dirty lens on the player, or condensation)
It may not be possible to play a disc recorded on a
computer, depending on the settings and environment of
the application that was used. Make sure to record discs in
a proper format (contact the application vendor for
details).
-
CD Extra
Audio CD (Session1)
Caution
!
-
-
It may not be possible to play back discs with insufficient
storage capacity.
This unit does not support discs containing multiple
formats (e.g. both MP3 and WMA tracks).
-
Do not try to play discs other than the ones listed above.
Doing so could cause noise, or prevent the unit from
functioning properly.
-
-
CD-G playback is not supported.
Although CD-R/CD-RW discs containing MP3 or WMA
tracks can be played back, the unit may have problems
playing certain discs, including failure to play the disc
correctly, noisy audio, or distorted sound.
CD-R and CD-RW discs that have not been finalized
cannot be played back. See the manual of the CD-R or CD-
RW recorder for details.
Limitations on Playback of MP3 Files
- Only MP3 files with the ".mp3" or ".MP3" file
extension can be played back.
- Files recorded in MPEG 1 Audio Layer 3 (64-384
kbps), with a sampling frequency of 44.1/48 kHz are
supported.
- Variable bit rates (VBR) of 32 to 320 kbps are
supported. Duration information may not be
displayed correctly during VBR playback.
-
-
-
Connect to a DTS-compatible device to play a DTS-CD.
Use in combination win an incompatible device could result
in noise.
When playing a DTS-CD, no audio is output from the
AUDIO OUTPUT ANALOG terminal.
12
Before Using This Product—Continued
Limitations on Playback of WMA Files
Precautions for Rental Discs
- WMA is an abbreviation of "Windows
Do not use discs with cellophane tape on them, or
rental discs or the like with loose, peeling, or peeled
labels. Using these discs could damage the unit, or
cause the discs to become stuck in the unit.
®
Media Audio." It is an audio compression
technology developed by Microsoft Corporation.
This unit supports WMA files encoded using
®
Windows Media Player versions 7, 7.1, and 8.
Precautions for Inkjet Printable Discs
- Only WMA files with the ".wma" or ".WMA" file
extension can be played back.
Do not leave discs whose label sides can be printed
using an inkjet printer in the unit for long periods.
Doing so could cause the disc to become stuck in the
unit, or cause the unit to malfunction. Remove such
discs from the unit when not playing them. Do not use
a disc immediately after printing.
- Encode WMA files using an application approved
by Microsoft Corporation. The unit may not
function normally if an unapproved application is
used.
- Variable bit rates (VBR) of 48 to 192 kbps (44.1
kHz) and 128 to 192 kbps (48 kHz) are supported.
Duration information may not be displayed correctly
during VBR playback.
Caring for Discs
- Copyright protected WMA files cannot be played
back.
Soiling can reduce signal capture, reducing audio and
video quality. If a disc becomes soiled, gently wipe off
fingerprints and dust from the playback surface using a
soft cloth, starting from the inside and working
outward.
Handling Discs
Nonstandard Discs
Do not use discs with special shapes (such as hearts or
octagons). Using these discs could damage the unit or
cause it to malfunction.
if the soiling is severe, dip a soft cloth in water, then
wring it out well, clean off the dirt, and then wipe off
the moisture with a soft cloth. Do not use spray for
analog records, antistatic agents, or the like. Never use
benzine, paint thinner, or other volatile chemicals.
Handling
Copyrights
Hold discs by the edge, or by the center hole and the
edge, in order to avoid touching the playback surface
(the surface with nothing printed on it).
Duplication, broadcasting, screening, wired
broadcasting, performance, rental, and loaning (free or
paid) of discs is prohibited by law.
Condensation
Water droplets may form inside the unit if it is brought
from a cold location to a warm room, or if a cold room
is heated quickly (e.g. using a space heater). This
process is called "condensation." If the unit is operated
in this state, it may not function properly, and may even
damage the disc or other components. We recommend
removing discs from the unit when it is not in use.
If there is a risk of condensation, leave the unit for
about an hour after turning on the power before use.
Underside
Do not put stickers or write on the playback or label
surface of the disc. Also be careful not to scratch or
otherwise damage the discs.
Precautions for Storage
Always keep discs in their dedicated cases. Store discs
away from direct sunlight, hot areas (such as near a
heater), and extremely cold areas.
13
Connecting to Other Devices
Connect to amplifiers, recording devices, and other equipment. There are two ways of connecting: analog and digital.
Select the connection type matching the type of audio you wish to enjoy.
Analog Connections
Digital Connections
Connect the supplied audio cable to the unit's AUDIO
OUTPUT ANALOG terminal and the audio
component's analog audio in terminal.
Use digital connections with audio components having
digital audio in terminals. There are two types of
digital audio out terminal: "OPTICAL" and
"COAXIAL." Use the connection method that is suited
to the component being connected.
C-S5VL
Notes
-
-
-
The audio output is the same for both OPTICAL and
COAXIAL.
To output digital audio, turn on the unit's DIGITAL OUT
switch.
If DIGITAL OUT is on (the DIGITAL OUT indicator on the
unit is illuminated) while a Super Audio CD is playing, digital/
analog audio will be output at PCM 44.1kHz/16 bits.
OPTICAL
Connect the unit's OPTICAL terminal and the audio
component's OPTICAL jack using a commercial
optical digital cable.
C-S5VL
Caution
!
-
Take care of the plug colors and the left and right channels
when connecting audio.
-
Insert plugs completely to ensure good connections. Loose
connections can cause noise or malfunctions.
Improper connection
Caution
!
Inserted completely
Plug optical digital cables straight in. Plugging them in at an
angle can damage the inlet of the OPTICAL terminal.
-
To prevent interference, keep audio cables away from
power cords and speaker cables.
14
Connecting to Other Devices—Continued
COAXIAL
Connecting to
Components
Capable
Connect the component using a commercial coaxial
digital cable.
You can control audiovisual amplifiers and receivers
using the supplied remote controller by connecting
C-S5VL
Onkyo audiovisual amps and receivers with
Use a cable to connect the unit's terminal with
the amp or receiver's terminal.
jacks.
Use the supplied audio cable to connect the unit's
AUDIO OUTPUT ANALOG terminal with the amp or
receiver's analog audio in terminal.
Caution
!
Be sure to connect the audio cables as well. The amp or
receiver cannot be controlled by the remote controller when
only the
cable and optical digital cable are connected.
C-S5VL
CD
Notes
-
-
-
See the manual of each component for information about
available system features.
Use the
jack.
terminal with products equipped with an
If there are two
jacks, they both operate identically.
Connect to either one of them.
15
Connecting to Other Devices—Continued
Connecting the Power Cord
Caution
!
-
Before connecting the power cord, connect all the other
components.
Turn off the unit before plugging or unplugging the power
cord.
-
Connect the other components. (See p.14)
Make sure that the unit is turned off.
Connect the supplied power cord to the unit's
AC INLET.
Caution
!
-
-
Always use the supplied power cord.
Never plug the power cord into the outlet before
connecting it to the unit. If the power cord is plugged in,
connecting or disconnecting it to/from the unit could cause
electric shock.
Plug the power cord into a household power
outlet.
To AC wall outlet
Notes
The unit manages the power polarity. To enjoy better audio, insert
the prong of the plug with a blade marking into the outlet hole
with the longer slit.
If the left and right slits are the same length, then the orientation of
the plug does not matter.
Caution
!
Always unplug the power cord from the outlet before
disconnecting it from the unit.
16
Disc Playback
CD And Super Audio CD Playback
Press the
button.
Press the POWER button on the front of the
unit to turn it on.
The tray closes, and playback begins.
Notes
-
-
When connecting an amplifier, you can reduce the impact on
the speakers by first turning on the unit, then the amplifier.
To turn off the unit, press the POWER button again.
If an amplifier is connected, first turn off the amplifier, then the
unit.
Digital Playback and Recording
-
If there is already a disc in the unit, playback will begin.
Press the DIGITAL OUT button to turn on digital
audio output.
When the button is pressed, the function is on if the
indicator next to it illuminates.
Digital audio output is turned off by default.
Press the to open the disc tray.
Notes
Place discs in the tray printed-side up.
-
-
The mode cannot be switched during playback.
When DIGITAL OUT is on, Super Audio CDs will also be
output digitally, but they will not be recorded digitally. Super
Audio CD audio will be converted to 44.1 kHz PCM/16 bit
before output.
When using an 8-cm (3") CD, place it in the
hollow inside the tray.
17
Disc Playback—Continued
Super Audio CD Hybrid Disc Playback
MP3 and WMA Playback
You can select to play back the CD area or Super
Audio CD area. Press the CD or SA-CD button on the
player, or the SA-CD/CD button on the remote
controller.
Press the POWER button on the front of the
unit to turn it on.
The indicator of the selected area illuminates.
Notes
-
-
When connecting an amplifier, you can reduce the impact on
the speakers by first turning on the unit, then the amplifier.
To turn off the unit, press the POWER button again.
If an amplifier is connected, first turn off the amplifier, then the
unit.
-
If there is already a disc in the unit, playback will begin.
Notes
-
The 2-channel area of the Super Audio CD area is played back.
The multi-channel area cannot be selected.
Press the to open the disc tray.
If a Super Audio CD only has multi-channel, then the left and
right (L/R) channels are played back.
The playback area cannot be switched for non-hybrid Super
Audio CD discs. The indicator will flash during playback.
The playback area cannot be switched during disc playback.
The indicator will flash if an operation is made to switch the
mode during playback.
-
-
Place discs in the tray printed-side up.
When using an 8-cm (3") CD, place it in the
hollow inside the tray.
18
Disc Playback—Continued
Press the to close the disc tray.
Press the FOLDER / buttons on the remote
controller, or the
/
buttons on the
player to select the folder in which the track to
play is located.
Notes
Numbers are automatically assigned to the folders and tracks.
Notes
001 ROOT
Folder
If you press the TRACK
When this appears, press the ENTER button to move up one
folder in the hierarchy.
/
buttons, "**-RTN" will appear.
002.MP3
File
Press the TRACK / buttons on the remote
controller to select the track to play, then press
the ENTER button.
MP3 001
MP3 002
MP3 003
003.MP3
MP3 001
Playback begins.
19
Available Actions During Playback
Stop Playback
Select Tracks
Press the button.
Press the
button to return to the start of the track
being played. Press it again to return to the previous
track.
Press the
button to advance to the next track.
Pause Playback
Press the button.
Specify a Track (CD or Super Audio
CD)
You can specify the track to play by number using the
number keys on the remote controller.
To specify the 10th and subsequent tracks, specify the
second digit (the "tens" place) using the +10 button.
Each time the button is pressed, the digit will increase
by one.
To resume playback, press the
again.
button or button
Example 1: To enter "10", press "+10" and "0".
Example 2: To enter "23", press "+10", "+10" and "3".
Fast Reverse/Fast Forward
Press and hold the
controller.
and
button on the remote
To perform this action from the front of the unit, press
and hold the or button.
20
Available Actions During Playback—Continued
Play a Specific Location on a Track
-
If you press the TRACK
When this appears, press the ENTER button to move up one
folder in the hierarchy.
/
buttons, "**-RTN" will appear.
When playing a CD or Super Audio CD, you can
specify the track number and the start time from which
to play back the track. When using a disc containing
MP3 or WMA tracks, you can specify the folder
number and track number.
Use the number keys to specify a track
number, then press the ENTER button.
The selected track is played.
This is explained below, using the example of the
procedure for specifying the track in the next location.
001
ROOT
Folder
002.MP3
File
MP3 001
MP3 002
Select Folders and Tracks
When using a CD or Super Audio CD disc, you can
select which track to play back.
MP3 013
When using a CD containing MP3 or WMA tracks,
you can select the track and folder to play back.
To select the folder, press the remote controller's
Press the remote controller's SEARCH button.
FOLDER and buttons. To select the track, press the
TRACK and buttons.
When playing back MP3 or WMA files, use the
number keys to specify the folder in which the
desired track is located, and then press the
FOLDER / buttons.
Notes
-
If there are no playable files in the specified folder, then "**-
RTN" will appear in the player's display. (The asterisks (**)
are the number of the next folder up in the hierarchy.)
If this appears, return to step 1, or press the
FOLDER
folder.
/
buttons on the remote controller to specify a
21
Available Actions During Playback—Continued
During MP3/WMA Playback
Eject the Disc
Each time you press the DISPLAY button, the display
changes as follows.
Press the button to open the disc tray. After
removing the disc, press the button again to close
the tray.
Elapsed track time
Current track name
(ID3 tag track name)
Folder name
Total number of folders
(The screen image shows an example of MP3
playback.)
Change the Displayed Information
Notes
You can change the information on the unit's display.
Press the DISPLAY button.
-
-
-
The unit can only display the folder and track names (ID3 tag
track name).
If a folder or track name (ID3 tag track name) is 7 characters or
longer, the 7th character and beyond are not displayed.
The unit can only display English letters and numbers. Some
characters may not be displayed.
During CD And Super Audio CD Playback
Each time you press the DISPLAY button, the display
changes as follows.
Elapsed track time
Remaining track time
Elapsed disc time
Remaining disc time
Notes
The TEXT information of Super Audio CDs is not displayed.
22
Playback Methods
In addition to listening to tracks in the order they were recorded on the disc, there are four other playback methods:
Repeat, A-B Repeat, Random, and Memory.
You can also mix multiple playback methods (for example, repeat + random or repeat + memory).
Press the remote controller's A-B button at the
location where you wish to end loop playback.
Repeat (Loop)
appears on the unit's display.
Repeatedly play the currently playing track, all tracks
in the folder in which the current track is located, or all
tracks on the disc.
Press the REPEAT button on the remote controller
repeatedly to toggle through the repeat (loop) types.
You can check the selected repeat method on the unit's
display.
Playback Status
Display Status
Press the button or A-B button to cancel loop
playback.
Ordinary play-
back
Loop single
track
Random (Shuffle)
Loop all tracks
in folder
Press the RANDOM button on the remote control to
play back tracks in shuffle mode.
If a disc containing MP3 or WMA files is being played,
and folders are being used, then you can select whether
to perform random playback on the entire disc or on a
folder.
Loop entire
disc
Press the RANDOM button again to return to normal
playback.
A-B Repeat (Loop between Two
Points)
Playback Status
Display Status
Use this mode to repeatedly play a range of tracks, by
specifying a starting point (point A) and stopping point
(point B).
Ordinary play-
back
The disc plays. (See p.17)
Random play-
back of entire
disc
Press the remote controller's A-B button at the
location where you wish to start loop playback.
Random play-
back of tracks
in a folder
appears on the unit's display.
(only for discs
containing
MP3 or WMA
tracks)
23
Playback Methods—Continued
Press the
button.
Memory Playback
You can use this mode to play any tracks you choose,
in any order.
Notes
You can store up to 32 tracks.
Configure CD/Super Audio CD Playback
Playback begins.
While playback is stopped, press the
MEMORY button on the remote controller.
Configure MP3/WMA Playback
While playback is stopped, press the
MEMORY button on the remote controller.
Use the number keys to enter the number of a
track you wish to play.
The number of the currently selected folder is
displayed, and the TRACK input prompt appears.
Example: To enter "12", press "1" and "2".
To change the folder, click FOLDER . Use the
number keys to enter the number of the folder
containing the desired track, then press the
FOLDER button.
Notes
Press the CLR button to clear your number input.
Press the ENTER button.
The track you entered is stored, and the screen for
storing the next track appears.
Display when folder number "2" is entered.
Notes
Press the CLR button to clear your number input.
Repeat steps 2 to 3 until you have selected the
tracks you wish to play.
24
Playback Methods—Continued
When TRACK flashes, enter the number of
the desired track using the number keys.
Check Your Stored Tracks
Press the TRACK / buttons to check the folder and
track numbers that have been stored in memory.
When they appear, press the CLR button to erase the
flashing item.
Example: To enter track 13, press "1" and "3".
Stop Memory Playback
Press the button to stop memory playback. At this
time, the stored tracks remain in memory.
When playback is stopped, press the button again,
then press the
button to cancel memory playback,
and return to the normal playback method.
While playback is stopped, press the CLR button to
erase all reserved items.
Press the ENTER button.
The track you entered is stored, and the screen for
storing the next track appears.
Notes
When the
button is pressed to open or close the tray, the stored
tracks are cleared from memory.
Notes
To switch folders, press the FOLDER button, then repeat steps 2
to 3.
Repeat steps 2 to 4 until you have selected the
tracks you wish to play.
Press the
button.
Playback begins.
25
Playback Methods—Continued
Add a New Track to Memory
Erase a Track from Memory
Press the MEMORY button on the remote
controller.
Press the MEMORY button on the remote
controller.
Press the TRACK / buttons to select the
track you wish to erase.
SACD/CD
Press the CLR button.
The selected track is erased.
MP3/WMA
Notes
The currently playing track cannot be erased.
Press the TRACK / buttons to select the
location to add.
SACD/CD
MP3/WMA
Press the ENTER button.
SACD/CD
MP3/WMA
Use the number keys to enter the number of
the folder and track you wish to play.
Notes
-
-
See the page below corresponding to your disc type for more
information about how to perform this operation.
Super Audio CD or CD: see p.24
MP3 or WMA: see p.24
To switch between FOLDER and TRACK input, press the
FOLDER
/
buttons.
Press the ENTER button.
The selected track is added to the memory.
26
Setup
Setup Menu List
FIL 1
Frequency Response
Ripple Characteristic
0.1
0
0
-50
PCM FILTER
FIL1(*)
-100
-150
-200
FIL2ㅜFIL5
-0.1
44.1
88.2
132.3
0
0
0
0
0
22.05
22.05
22.05
22.05
22.05
Frequency (kHz)
Frequency (kHz)
DSD FILTER
PHASE
DIRECT(*)
FIL 2
Frequency Response
Ripple Characteristic
FIL1ㅜFIL4
0.1
0
0
-50
NORMAL(*)
INVERT
-100
-150
-200
-0.1
44.1
88.2
132.3
Frequency (kHz)
Frequency (kHz)
AREA PRIORITY
SACD(*)
CD
FIL 3
Frequency Response
Ripple Characteristic
0.1
0
0
-50
-100
-150
-200
-0.1
44.1
88.2
132.3
Frequency (kHz)
Frequency (kHz)
FIL 4
* Default setting
Frequency Response
Ripple Characteristic
0.1
0
0
Available Settings
-50
-100
-150
-200
PCM FILTER
-0.1
44.1
88.2
132.3
Frequency (kHz)
Frequency (kHz)
When using analog output, you can apply a digital
filter to the PCM data before it is passed through the D/
A converter.
The digital filter can switch the properties in the
audible or inaudible frequency ranges. Select the
setting that you prefer (FIL 1 to FIL 5).
The default setting is FIL 1.
FIL 5
Frequency Response
Ripple Characteristic
0.1
0
0
-50
-100
-150
-200
For a Super Audio CD, this setting is enabled when the
unit's DIGITAL OUT is switched on. For a CD, this
setting is always enabled, regardless of the unit's
DIGITAL OUT setting.
-0.1
44.1
88.2
132.3
Frequency (kHz)
Frequency (kHz)
27
Setup—Continued
DSD FILTER
PHASE
When using analog output while playing a Super Audio
CD, you can apply a digital filter to the DSD data
before it is passed through the D/A converter.
The digital filter can switch the properties in the
audible or inaudible frequency ranges.
Select the setting that you prefer.
Set whether to invert the phase of the analog output.
NORMAL (Default setting)
This outputs the waveform recorded on the CD with
the phase unchanged.
The default setting is DIRECT.
INVERT
When a Super Audio CD is playing, this setting is
enabled when the unit's DIGITAL OUT is switched off.
FIL 1
This outputs the waveform recorded on the CD with
the phase inverted 180°.
AREA PRIORITY
Frequency Response
Ripple Characteristic
15
10
5
0
-20
-40
-60
-80
-100
Select the area to get priority for playback when a
Super Audio CD hybrid disc is played. The default
setting is SACD.
0
-5
-10
-15
0
100
200
200
200
200
10
20
0
0
0
0
Frequency (kHz)
Frequency (kHz)
FIL 2
Frequency Response
Ripple Characteristic
15
10
5
0
-20
-40
-60
-80
0
-5
-10
-15
-100
0
100
10
20
Frequency (kHz)
Frequency (kHz)
FIL 3
Frequency Response
Ripple Characteristic
15
10
5
0
-20
-40
-60
-80
0
-5
-10
-15
-100
0
100
10
20
Frequency (kHz)
Frequency (kHz)
FIL 4
Frequency Response
Ripple Characteristic
15
10
5
0
-20
-40
-60
-80
0
-5
-10
-15
-100
0
100
10
20
Frequency (kHz)
Frequency (kHz)
28
Setup—Continued
Making Settings
Caution
!
If this setting is changed during playback, it may not be
possible to store the changed settings in memory. If you have
changed the settings during playback, stop playback and
other actions, and then turn off the power.
Press the SETUP button on the remote
controller.
The last item to be configured the last time you
performed setup appears.
Press the FOLDER / buttons, and select the
item you wish to configure.
Press the TRACK / buttons, and select the
setting value.
When you are finished making settings, press
the ENTER button.
"FINISH" appears in the display.
Your settings are enabled, and you are returned to
normal mode.
Notes
-
-
The settings will not be enabled unless you press the ENTER
button.
Press the SETUP button to cancel your settings.
29
Troubleshooting
If you run into problems with the unit, look for a solution below. The problem could also be caused by one of the
components connected to the unit, so please also check the manuals of each device.
Caution
!
-
This unit contains a sophisticated microcomputer for signal processing and control functions. In very rare situations, however, severe
interference, noise from an external source, or static electricity may cause it to lock up. If this happens, turn off the unit, wait for
about five seconds, and then turn it on again.
Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit's malfunction. Before
you record important data, make sure that the material will be recorded correctly.
-
Returning Settings to the Defaults
Perform the steps below to return all settings to their default values.
Remove the disc from the player.
"NoDISC" appears in the player's display.
While pressing on the unit, press the CD button.
"INIT" appears in the display, followed by "FINISH".
This completes the initialization of the settings.
Power
Problem
Solution
See Page
16
No power
Make sure that the power cord is properly plugged into the wall outlet. Also
make sure that the power cord is properly connected to the unit's AC inlet.
Disc Playback
Problem
Solution
See Page
17
Can not play disc
Make sure that the disc is placed in the disc tray properly, and that the disc is
placed in the tray printed-side up.
Make sure that the disc is not dirty.
13
12
Make sure that this CD player can play the disc.
If there is a risk of condensation, leave the unit for about an hour after turning on 13
the power before use.
Can not play tracks in the disc's playback order Turn off any special playback modes (e.g. repeat, memory, or random).
23
It takes too long to select tracks (to find the
specified track)
Make sure that the disc isn't dirty. Clean the disc surface. If the disc is scratched, 13
replace it.
Can not store tracks in memory
Make sure that the disc is placed in the disc tray properly, and that the track
number you are specifying exists on the disc.
24
30
Troubleshooting—Continued
Playing Music CDs with Copy Control Functions
Problem
Solution
See Page
-
There is noise during playback, or the audio
skips
You are playing back a music CD with a copy control function. Some music CDs
with copy control functions do not meet CD standards. Since these are special
discs, this unit may not be able to play them.
The disc is not recognized, and "NoDISC"
appears in the display
The first track is not played
It takes longer than usual to go to the start of a
track
Tracks start playing in the middle
Some locations can not be played back
Playback stops partway through
The display is wrong
Audio
Problem
Solution
See Page
No audio is output for the disc being played
(both analog and digital connections)
Make sure that the cables are plugged in all the way.
14
-
Make sure that the connected component's input terminal and the input settings
are correct.
Make sure that the amp's volume isn't set to the lowest level, and that the volume
isn't muted.
-
If headphones are plugged into the player, adjust the headphone volume using
the PHONES LEVEL control on the unit.
-
No audio is output for the disc being played
(digital connection)
Make sure the Digital Out button isn't set to "off." When making a digital
connection, set the Digital Out button to "on."
17
-
I hear noise in the audio
The unit may be picking up interference from another digital component. Turn
off the power of peripheral devices, and check for the source of the noise. After
doing so, move components causing noise away from the unit.
The audio playback quality of Super Audio
CDs is poor.
The sound quality may suffer if you play back a Super Audio CD with DIGITAL 17
OUT on. You should normally keep it off.
Remote Controller
Problem
Solution
See Page
The buttons on the CD player work, but the
buttons on the remote controller do not
Install two new batteries.
6
Make sure that the remote controller is not too far away from the unit, and that
there is no obstruction between the unit and the remote controller.
11
Make sure that the unit's remote control sensor is not exposed to bright light
(inverted fluorescent light or direct sunlight).
11
11
-
Make sure that the audio rack does not have colored or tinted glass. This could
prevent the remote controller from functioning properly.
The AV receiver volume and muting controls
do not work
Change the ID of the AV receiver to 2.
31
Troubleshooting—Continued
Devices
Problem
The
Solution
See Page
15
system features do not work.
Make sure that both the
the component. The system will not function if only the
cable and audio cable are connected correctly to
cable and digital
cable are connected. Check the amplifier and AV receiver input. Also check the
manual of each device, because there may be settings that prevent connected
devices from operating.
32
Specifications
Audio Output
Frequency Response
: CD
Super Audio CD
: CD
Super Audio CD
: At least 100 dB
: 0.0025 %
: Digital/Optical
Digital/Coaxial
Analog
4 Hz to 20 kHz
4 Hz to 50 kHz
114 dB
Signal to Noise Ratio
110 dB
Audio Dynamic Range
THD (Total Harmonic Distortion)
Output/Impedance
-22.5 dBm
0.5 V (p-p) / 75 Ohms
2.0 V (rms) / 500 Ohms
General
Power Supply
: North America
Others
AC 120 V, 60 Hz
100 V - 240 V, 50/60 Hz
Power Consumption
Dimensions (WxHxD)
: 15 W
: 435 x 80 x 318 mm
17-1/8"×3-1/8"×12-1/2"
: 4.5 kg (9.9 lbs)
Weight
Operating Condition Temperature/Humidity : 5 °C - 35 °C (41 °F - 95 °F) / 5 % - 85 %
Playable Discs
: Super Audio CDs, audio CDs, CD-R/RW(*), MP3, WMA
*It may not be possible to play back discs that have not been finalized. It
also may not be possible to play back the disc depending on its type or
the recorder used.
Specifications and features are subject to change without notice.
33
Memo
34
Memo
35
Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN
Tel: 072-831-8023 Fax: 072-831-8163
ONKYO U.S.A. CORPORATION
18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.
ONKYO EUROPE ELECTRONICS GmbH
Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY
ONKYO EUROPE UK Office
Suite 1, Gregories Court, Gregories Road, Beaconsfield, Buckinghamshire, HP9 1HQ
UNITED KINGDOM Tel: +44-(0)1494-681515 Fax: +44(0)-1494-680452
HOMEPAGE
ONKYO CHINA LIMITED
Unit 1&12, 9/F, Ever Gain PlazaTower 1, 88, Container Port Road, Kwai Chung,
N.T., HONG KONG Tel: 852-2429-3118 Fax: 852-2428-9039
W0906-2
SN 29400088A
(C) Copyright 2009 ONKYO CORPORATION Japan. All rights reserved.
ª ² ¹ ´ ° ° ° ¸ ¸ Á ª
|