Enterprise Edge
M7310
Quick Reference Guide
© 2000 Nortel Networks
P0908513 Issue 03
Your Enterprise Edge M7310 Telephone
Shift button
For using the top function of a dual-memory button.
Display
shows the time, date, call information, and guides you.
The lower line of the display is reserved for display button instructions.
Dual-memory buttons
store any two features and/or autodial numbers.
Display buttons
Feature button
starts or ends a feature.
Release button
cancels active calls.
Hold button
Dial pad
Memory and line buttons
are buttons with indicators for one
touch dialing, feature operation
or line access.
Volume control
Indicators
appear beside lines and features.
Three display buttons appear
directly below the display. When
active, these buttons appear in
capital letters on the second line of
the display. In this document,
display buttons appear as
underlined, capital letters: for
example, OK.
Using display
buttons
Contrast level 2
DOWN UP OK
Display message
Display button
message
Display buttons
Using Button
Inquiry
Check what is programmed on your memory buttons.
1. Release all calls or lines with dial tone.
2. Press ƒ•‚.
3. Press the button(s) that you want to check and read the display.
4. Press ƒ when finished.
Adjusting display
contrast
1. Press ƒ•‡.
2. Press UP or DOWN for the level you want.
3. Press OK when finished.
Selecting a ring
type and volume
level
1. Press ĥfl.
2. Press ⁄, ¤, ‹, ›, or NEXT to hear the different ring types.
3. While the telephone is ringing, press √ to adjust the
volume level.
4. Press OK to store the volume level and ring.
Page 1 Enterprise Edge M7310 Quick Reference Guide
Making and answering calls
Answering
calls
Answering calls using the handset
When your telephone rings, or º flashes beside an Intercom or line
button:
1. Lift the handset.
OR
Press the button beside the flashing º before lifting the handset.
Answering calls using Handsfree
When your telephone rings, or º flashes beside an Intercom or line
button:
1. Press ©.
Making calls
Depending upon the dialing mode programmed on your telephone, you
may have to lift the handset before making a call.
¬
External calls using numbered line buttons
1. If you do not have an external Prime line, press a line button.
2. Dial your call.
∆
External calls using Intercom buttons
1. Lift the handset.
2. If º appears beside an Intercom button, enter a line pool access code.
OR
Press an Intercom button without º, then enter a line pool access
code.
3. When you hear external dial tone, dial your call.
Internal calls using Intercom buttons
1. If you do not have an internal Prime line, press ∆.
2. Dial your call.
Note: Line pool access codes and extension numbers are supplied by
your System Administrator.
˙
Holding Calls
1. Press ˙. The º flashes beside the line on hold.
2. Press the line button with the flashing º to return to the call.
Automatic hold
Calls are put on hold automatically when you switch from one line to
another.
Exclusive hold
Use Exclusive Hold (ƒ˙) to keep a call on hold so that
it can be retrieved only at your telephone.
Page 2 Enterprise Edge M7310 Quick Reference Guide
Making and answering calls continued
©
System Administrator can program Handsfree for your telephone.
Switching between Handsfree and handset
1. Press © and replace the handset to switch to Handsfree.
2. Pick up the handset to switch back.
Using Mute
1. Press ©microphone OFF.
2. Press © again to turn the microphone ON.
Making calls using Handsfree
Press © instead of lifting the handset.
Notice
This telephone now conforms to the latest standards in relation to the
positioning of Q and Z on the number keys. The Q appears on key
number 7 and the Z appears on key number 9.
Page3EnterpriseEdgeM7310QuickReferenceGuide
Programming memory buttons
About memory buttons
Memory buttons store telephone
numbers or feature codes to
give you one-touch dialling or
feature activation.
To use the top function, press
the shift button, then press the
dual-memory button.
There are two types of memory
buttons: single-memory and
dual-memory.
Dual-memory buttons:
To use the bottom function,
press the dual-memory button.
Single-memory buttons:
Single-memory buttons are the
buttons with indicators other
than line or Handsfree buttons.
Remember: Press ƒ•‚ to check a memory or line button.
External Autodial Internal Autodial
1. If you are on a call or an open line 1. If you are on a call or an open line with
Programming
memory buttons
with dial tone, press
dial tone, press
˙ or ®
˙ or ®.
2. Press ƒ•⁄.
3. Press a memory button.
4. Dial the external number.
2. Press ƒ•¤.
3. Press a memory button.
4. Dial the station number.
5. Press OK to store the number. 5. Label your new button.
6. Label your new button.
Features
Erasing memory buttons
1. If you are on a call or an open line 1. If you are on a call or an open line with
with dial tone, press
˙ or ®.
2. Press ƒ•‹.
3. Press a memory button.
4. Press ƒ and the
feature code.
dial tone, press
˙ or ®.
2. Press ƒ•⁄.
3. Press the memory button you want to
erase.
4. Press OK to erase the button.
5. Label your new button.
Page 4 Enterprise Edge M7310 Quick Reference Guide
Setting up the telephone
ATTENTION Before attempting to carry
out any work on the telephone, ensure
that the line cord is unplugged from the
wall socket.
Connecting the cords
To remove any of the cords, squeeze the
release latch on the plug and gently pull
the plug from the socket.
Connect the handset cord to the jack
labelled with the telephone icon and route
the cord as shown.
If you are using a headset, route the cord
along the channel in the base and connect
the cord to the telephone jack that is
marked with the headset icon.
Connect to jack
from distribution block
Route the line cord through the stand and
connect the cord to the telephone jack that
is marked with the jack icon.
Connect to receiver
Attach the stand using the slots on the
back of the telephone.
Once the above work is complete, plug the
line cord back into its wall socket.
Page 5 Enterprise Edge M7310 Quick Reference Guide
Setting up the telephone
Mounting the
telephone on
the wall
Page 6 Enterprise Edge M7310 Quick Reference Guide
P0908513 Issue 03
|