Nokia E61i User Guide
Contents
Picture messages..................................................................................25
Device memory.....................................................................................17
Hear your messages................................................................................18
Organize messages.................................................................................22
Search for messages...............................................................................22
View e-mail offline...............................................................................23
C o n t e n t s
Send calendar entries.............................................................................47
9. Clock..........................................................................................48
Email data roaming................................................................................53
Internet access points............................................................................53
C o n t e n t s
Trip distance view................................................................................77
Navigator settings................................................................................78
For your safety
Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information.
SWITCH ON SAFELY
Do not switch the device on when wireless phone use is prohibited or when it may cause interference or danger.
ROAD SAFETY COMES FIRST
Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should
be road safety.
INTERFERENCE
All wireless devices may be susceptible to interference, which could affect performance.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the device off near medical equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause interference in aircraft.
SWITCH OFF WHEN REFUELING
Do not use the device at a refueling point. Do not use near fuel or chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the device where blasting is in progress.
USE SENSIBLY
Use only in the positions as explained in the product documentation. Do not touch the antenna areas unnecessarily.
QUALIFIED SERVICE
Only qualified personnel may install or repair this product.
ENHANCEMENTS AND BATTERIES
Use only approved enhancements and batteries. Do not connect incompatible products.
WATER-RESISTANCE
Your device is not water-resistant. Keep it dry.
BACK-UP COPIES
Remember to make back-up copies or keep a written record of all important information stored in your device.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products.
EMERGENCY CALLS
Ensure the phone function of the device is switched on and in service. Press the end key as many times as needed to clear the display
and return to the standby mode. Enter the emergency number, then press the call key. Give your location. Do not end the call until
given permission to do so.
About your device
The wireless device described in this guide is approved for use on the GSM 850/900/1800/1900, UMTS 2100 network. Contact your
service provider for more information about networks.
When using the features in this device, obey all laws and respect local customs, privacy and legitimate rights of others, including
copyrights.
Copyright protections may prevent some images, music (including ringing tones), and other content from being copied, modified,
transferred, or forwarded.
Your device supports internet connections and other methods of connectivity. Like computers, your device may be exposed to viruses,
malicious messages and applications, and other harmful content. Exercise caution and open messages, accept connectivity requests,
download content, and accept installations only from trustworthy sources. To increase the security of your devices, consider installing,
using, and regularly updating antivirus software, firewall, and other related software on your device and any connected computer.
Warning: To use any features in this device, other than the alarm clock, the device must be switched on. Do not switch the device on
when wireless device use may cause interference or danger.
© 2007 Nokia. All rights reserved.
6
F o r y o u r s a f e t y
The office applications support common features of Microsoft Word, PowerPoint, and Excel (Microsoft Office 2000, XP, and 2003). Not all file
formats can be viewed or modified.
Network services
To use the phone you must have service from a wireless service provider. Many of the features require special network features. These features
are not available on all networks; other networks may require that you make specific arrangements with your service provider before you can
use the network services. Your service provider can give you instructions and explain what charges will apply. Some networks may have
limitations that affect how you can use network services. For instance, some networks may not support all language-dependent characters and
services.
Your service provider may have requested that certain features be disabled or not activated in your device. If so, these features will not appear
on your device menu. Your device may also have a special configuration such as changes in menu names, menu order, and icons. Contact your
service provider for more information.
This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some features of this device, such as e-mail, browsing,
multimedia messages, and content downloading, require network support for these technologies.
Enhancements, batteries, and chargers
Always switch the device off and disconnect the charger before removing the battery.
Check the model number of any charger before use with this device. This device is intended for use when supplied with power from the AC-3,
AC-4 and AC-5 chargers and from ACP-7, ACP-8, ACP-9, ACP-12, LCH-12 and AC-1 when used with the CA-44 adapter.
Warning: Use only batteries, chargers, and enhancements approved by Nokia for use with this particular model. The use of any other
types may invalidate any approval or warranty, and may be dangerous.
For availability of approved enhancements, please check with your dealer. When you disconnect the power cord of any enhancement, grasp
and pull the plug, not the cord.
© 2007 Nokia. All rights reserved.
7
1.
Get started
The images in this guide may differ from your device display.
Model number: Nokia E61i-1.
Hereinafter referred to as Nokia E61i.
Insert the SIM card and battery
For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider or
other vendor.
1. Always switch the device off and disconnect the charger before removing the battery.
With the back of the device facing you, press and hold the cover release button (1), and slide the back cover in the direction
of the arrow (2).
2. If the battery is installed, lift the battery from the battery compartment in the direction of the arrow to remove it .
3. Ensure that the beveled corner of the SIM card is pointing towards the bottom of the device and that the contact area on the
card is facing the device, then insert the SIM card (1) into the SIM card slot (2).
4. To insert the battery, align the contacts of the battery with the corresponding connectors on the battery compartment, insert
in the direction of the arrow, and gently click the battery into place.
© 2007 Nokia. All rights reserved.
8
G e t s t a r t e d
5. To replace the back cover, slide the cover in the direction of the arrow.
Instead of a SIM card, you may also have a USIM card, which is an enhanced version of the SIM card and is supported by UMTS
(network service) mobile phones. Contact your service provider for more information.
Insert and remove a memory card
Use only compatible microSD cards approved by Nokia for use with this device. Nokia uses approved industry standards for
memory cards, but some brands may not be fully compatible with this device. Incompatible cards may damage the card and
the device and corrupt data stored on the card.
If you have a memory card, follow the instructions to insert and remove it.
1. Remove the battery cover.
2. Insert the memory card (1) fully into the memory card slot (2) to lock in place. Ensure that the contact area is facing down.
3. Replace the battery cover.
4. To remove the memory card, press the power key and select Remove mem. card. Remove the battery cover and push the
memory card into the device to activate the release mechanism. Then, gently pull the card out of your device.
Charge the battery
1. Connect the charger to a wall outlet.
2. Connect the charger to the bottom of the device. The battery indicator bar starts scrolling on the display. If the battery is
completely discharged, it may take a few minutes before the charging indicator is shown. The device can be used while
charging.
3. When the battery is fully charged, the bar stops scrolling. Disconnect the charger from the device, then from the outlet.
When the battery charge level is too low for operation, the device switches itself off.
Switch on your device
1. To switch the device on, press and hold the power key.
2. If the device asks for a PIN code (or UPIN code, if you have a USIM card), lock code or security code, enter the code, and select
OK.
3. When you switch on the device for the first time, your device asks for the current time, date, and the city in which you are
located. To switch the time from a.m. to p.m., scroll down. To find your city, enter the first letters of the city name. It is
important to select the correct city, because scheduled calendar entries may change if you change the city later and the new
city is located on a different time zone. You can change these settings later in Clock.
© 2007 Nokia. All rights reserved.
9
G e t s t a r t e d
4. Your device opens a Welcome application, which provides you basic information about your device and its use. See
5. To switch the device off, press and hold the power key.
Tip: When you switch the device on, it may recognize the SIM card provider and configure the correct text message,
multimedia message, and GPRS settings automatically. If not, contact your service provider for the correct settings, or
use the Sett. wizard application.
The device can be used without the network dependant phone functions when a SIM card is not inserted or when the Offline
profile is selected.
Keys and parts
1 — Power key
2 — Navi™ scroll key (hereinafter the scroll key)
3 — Right selection key
4 — End key
5 — Own key
6 — E-mail key
7 — Backspace key
8 — Enter key
9 — Chr key
10 — Shift key
11 — Ctrl key
12 — Spacebar
13 — Blue function key
14 — Phone keypad
15 — Menu key
16 — Contacts key
17 — Call key
18 — Left selection key
19 — Notification light and light sensor
1 — Loudspeaker
2 — Volume keys
© 2007 Nokia. All rights reserved.
10
G e t s t a r t e d
3 — Voice key
Key functions
Selection keys
Press either selection key to use the command that is shown on the display above the selection keys. See "Standby
modes," p. 13. To change the shortcuts in the standby mode, select Menu > Tools > Settings > Phone > Standby mode, and
the applications in Left selection key and Right selection key.
Scroll key
Press the scroll key to edit or make a selection, or to access commonly used functions in the different applications. Use the scroll
key to scroll left, right, up, down, or to move around on the display (for example, when browsing). In the standby mode, scroll
with or press the scroll key for different shortcuts. To change the shortcuts, select Menu > Tools > Settings > Phone > Standby
mode > Active standby > Off, and the shortcuts in Navigation key right, Navigation key left, Navigat. key down, Navigation
key up, and Selection key.
Call and end keys
To answer a call, press the call key. In the standby mode, press the call key to access the Log.
To reject a call, end active calls and held calls, and close applications, press the end key. Press and hold the end key to end data
connections (GPRS, data call).
Own key
You can configure the Own key to open any application, web page, or bookmark that you often need and want to access quickly.
The bookmarks opened with the Own key only work with the Services browser. To select the application you want the Own key
to open, select Menu > Tools > Own key.
Tip: You can also press and hold the Own key to configure it.
E-mail key
To access your default e-mail inbox, press the e-mail key. If you have not set up an e-mail account, the mailbox guide opens to
help you. If you press and hold the e-mail key, your default e-mail editor opens. The functionality depends also on your mailbox
service provider. You can configure the e-mail key yourself. See "Configure the e-mail key," p. 23.
Chr key
To insert characters that you cannot insert with the keypad, press the Chr key when you are writing.
To scroll through a list of accented characters, press and hold the Chr key, then press the other key as many times as you need
to get the accented character you want.
Shift keys
To enter an uppercase letter in the middle of lowercase letters or a lowercase letter in the middle of uppercase letters, press
the shift key so that
is shown on the display, then the key you want.
To enter only uppercase letters, press the shift key twice, so that
is shown on the display. To enter only lowercase letters
again, press the shift key twice, so that is shown on the display.
To select text, press the shift key, and scroll left or right.
Blue function key
To enter a character marked in blue, press the blue function key, so that is shown on the display, then the key you want.
To enter only characters marked in blue, press the blue function key twice so that is shown on the display, then the characters
you want.
To activate Bluetooth, press the blue function key and Ctrl key simultaneously. To deactivate Bluetooth, press the blue function
key and Ctrl key again.
To activate infrared, press the blue function key and Chr key simultaneously.
Menu key
Leaving applications running in the background increases the demand on battery power and reduces the battery life. To access
the applications in your device, press the menu key in the standby modes. To return to Menu from an application, leaving the
application open in the background, press the menu key. Press and hold the menu key to see a list of the active applications
and switch between them. In this user guide, "select Menu" refers to pressing this key.
Contacts key
To access the Contacts directory from any application, press the contacts key.
© 2007 Nokia. All rights reserved.
11
G e t s t a r t e d
Voice key
Press the voice key to open Recorder. Press and hold the voice key to use voice commands. See "Voice commands," p. 41.
Camera
You can take photos or record video clips with the built-in camera. The camera lens is on the back of the device, and the display
works as a viewfinder.
To take a picture, select Menu > Media > Camera. Use the display as a viewfinder, aim at your subject,
and press the scroll key. The device saves the photo in the default folder, or in the folder you have
defined.
Lock the keys
When the keypad lock is on, calls may be possible to the official emergency number programmed into your device.
Lock the keys to prevent accidental keypresses.
To lock the keys in the standby mode, press the left selection key (1) and the blue function key (2).
To unlock, press the left selection key and the blue function key again.
Tip: To lock the keys in the Menu or in an open application, press the power key briefly,
and select Lock keypad. To unlock, press the left selection key and the blue function key.
When the device is locked, calls may be possible to the official emergency number programmed
into your device. You can also lock the device in the standby mode using your lock code. Press the
power key, select Lock phone, and enter your lock code. The default lock code is 12345. To unlock,
press the left selection key, enter your lock code, and press the scroll key.
Connectors
Warning: When you use the headset, your ability to hear outside sounds may be affected. Do not use the headset
where it can endanger your safety.
Pop-Port™ connector for headset and other
enhancements
Battery charger connector
Infrared port
Antennas
Your device has internal antennas.
Note: As with any radio transmitting device, avoid touching an antenna unnecessarily when the antenna is in use. For
example, avoid touching the cellular antenna during a phone call. Contact with a transmitting or receiving antenna
affects the quality of the radio communication, may cause the device to operate at a higher power level than otherwise
needed, and may reduce the battery life.
© 2007 Nokia. All rights reserved.
12
G e t s t a r t e d
The picture shows the normal use of the device at the ear for voice calls.
Volume control
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely
loud.
To adjust the volume during a call, press the volume keys.
To adjust the volume when using the loudspeaker, press the volume keys.
About the display
A small number of missing, discolored, or bright dots may appear on the screen. This is a characteristic of this type of display.
Some displays may contain pixels or dots that remain on or off. This is normal, not a fault.
Standby modes
Your device has two different standby modes: active standby mode and standby mode.
Active standby mode
After you have switched on your device and it is ready for use, but you have not entered any characters or made other selections,
the device is in the active standby mode. In the active standby mode, you can view your service provider and network, different
indicatorssuchasindicatorsforalarms, andapplicationsyouwanttoaccessfast. Youcan, forexample, viewcalendarinformation
such as the day's meetings in the active standby mode. Scroll to the information, and press the scroll key to open calendar for
details.
To select the applications that you want to access from active standby, select Menu > Tools >
Settings > Phone > Standby mode > Active standby apps.. Scroll to the different shortcut settings,
and press the scroll key. Scroll to the desired application, and press the scroll key.
You can see the messages in a messaging folder such as inbox or mailbox in the active standby mode.
Select Menu > Tools > Settings > Phone > Standby mode and the folders in Active standby
mailbox.
Tip: You can also see different notifications, such as missed calls, unread messages, or voice
mails in the active standby mode. With these notifications, you can see the communication
status of your device with one glance. Select the plug-ins in Menu > Tools > Settings >
Phone > Standby mode > Active standby plug-ins. The available plug-ins may vary.
To use the basic standby mode, select Menu > Tools > Settings > Phone > Standby mode > Active standby > Off.
To call your voice mailbox (network service), press and hold 1.
To open Services and connect to the Web, press 0.
Standby mode
In the standby mode, you can see different information, such as your service provider, time, and different indicators, including
indicators for alarms.
In the standby mode, you can use the following shortcuts. These shortcuts are usually not available in the active standby mode,
where the scroll key is used for normal scrolling.
To view the most recently dialed numbers, press the call key. Scroll to a number or name, and press the call key again to call the
number.
© 2007 Nokia. All rights reserved.
13
G e t s t a r t e d
To call your voice mailbox (network service), press and hold 1.
To access the calendar, scroll right.
To write and send text messages, scroll left.
To launch the Camera application, scroll up.
To access your contacts, scroll down or press the scroll key.
To change the profile, press the power key briefly, scroll to the profile you want, and press the scroll key to activate the profile.
To open Services and connect to the Web, press 0.
To change these shortcuts, select Menu > Tools > Settings > Phone > Standby mode.
Display indicators
The device is being used in a GSM network. The bar next to the icon indicates the signal strength of the network at your
current location. The higher the bar, the stronger the signal.
The device is being used in a UMTS network (network service). The bar next to the icon indicates the signal strength of the
network at your current location. The higher the bar, the stronger the signal.
The battery charge level. The higher the bar, the stronger the charge in the battery.
You have one or more unread messages in the Inbox folder in Messag..
You have received new e-mail in the remote mailbox.
The device keypad is locked.
The device is locked.
You have one or more missed phone calls.
An alarm is active.
You have selected the silent profile, and the device does not ring for an incoming call or message.
Bluetooth is on.
An infrared connection is active. If the indicator blinks, your device is trying to connect to the other device, or the connection
has been lost.
A GPRS or EGPRS packet data connection is available.
A UMTS packet data connection is available.
A GPRS or EGPRS packet data connection is active.
A UMTS packet data connection is active.
A GPRS or EGPRS packet data connection is on hold.
A UMTS packet data connection is on hold.
You have set the device to scan for wireless LANs, and a wireless LAN is available.
A wireless LAN connection is active in a network that does not have encryption.
A wireless LAN connection is active in a network that has encryption.
The device is registered with a SIP server, and you can make net calls.
Your device is connected to a PC with a USB data cable.
A data call is active.
and Indicate the phone line that you have selected, if you have subscribed to two phone lines (network service).
All calls are forwarded to another number.
A headset is connected to the device.
The connection to a headset with Bluetooth connectivity has been lost.
A hands-free car kit is connected to the device.
A loopset is connected to the device.
Text phone is connected to the device.
Your device is synchronizing.
© 2007 Nokia. All rights reserved.
14
G e t s t a r t e d
You have an ongoing push to talk connection. If push to talk is not available from your wireless service provider, it may
not appear in the menu of your device.
Indicators for the selected character mode.
,
,
You have pressed the blue function key once to insert a number or a character marked with blue color on the keypad.
You have pressed the blue function key twice to insert only numbers or characters marked with blue color on the keypad.
You have pressed the shift key once to insert an uppercase letter in the middle of lowercase letters, or a lowercase letter in
the middle of uppercase letters.
Help and tutorial
You can find answers to your questions while using the device even with no user guide present, because your device includes
both a help and a tutorial.
Device help
You can access the device help from an open application or from the Menu. When you have an application open, select
Options > Help to read instructions for the current view.
To open help from Menu, select Menu > Help > Help. In Help, you can select categories for which you want to see instructions.
Scroll to a category, such as Messaging, and press the scroll key to see what instructions (help topics) are available. While you
are reading the topic, scroll left or right to see the other topics in that category.
When you are reading the instructions, press and hold the menu key to switch between help and the application that is open
in the background.
Tutorial
The tutorial provides you information about your device and shows you how to use it. Some tutorial content may be located
on a memory card. You must insert the memory card in the device before you can access it.
To access the tutorial in the Menu, select Menu > Help, open Tutorial and the section you want to view.
Nokia PC Suite
You can install Nokia PC Suite from the CD-ROM or from the Web. Nokia PC Suite can be used only with Windows 2000 and
Windows XP. With Nokia PC Suite, you can make backups, synchronize your device with a compatible computer, move files
between your device and a compatible computer, or use your device as a modem.
Nokia support and contact information
downloads, and services related to your Nokia product.
On the Web site, you can get information on the use of Nokia products and services. If you need to contact customer service,
For maintenance services, check your nearest Nokia service center at www.nokia.com/repair.
© 2007 Nokia. All rights reserved.
15
2.
Basic information about your device
Welcome
Select Menu > Help > Welcome.
When you switch on your device for the first time, the Welcome application opens. Select from the following:
•
•
•
Tutorial provides information about your device and shows you how to use it.
Transfer enables you to transfer content, such as contacts and calendar entries, from a compatible Nokia device. See "Transfer
Operator contains a link to your operator's home portal.
•
Menu
The Menu is a starting point from which you can open all applications in the device or on a memory card. The Menu contains
applications and folders, which are groups of similar applications. Use the scroll key to scroll up and down on the screen.
Applications that you install are saved in the Installat. folder by default.
To open an application, scroll to it, and press the scroll key.
To view the applications in a list, select Options > Change view > List. To return back to the grid view, select Options > Change
view > Grid.
To view the memory consumption of different applications and data stored on the device or memory card and to check the
amount of free memory, select Options > Memory details and the memory.
To rearrange the folder, scroll to the application you want to move, and select Options > Move. A check mark is placed beside
the application. Scroll to a new location, and select OK.
To move an application to a different folder, scroll to the application you want to move to another folder, and select Options >
Move to folder, the new folder, and OK.
To download applications from the Web, select Options > App. downloads.
To create a new folder, select Options > New folder. You cannot create folders inside folders.
To rename a new folder, select Options > Rename.
Tip: To switch between several open applications, press and hold the menu key. The application-switching window
opens and displays the open applications. Scroll to an application, and press the scroll key to switch to it.
Scroll and make selections
Use the scroll key to move and make selections. With the scroll key, you can move up, down, left and right in the Menu or in
different applications or lists. You can also press the scroll key to open applications, files, or edit settings.
To select text, press and hold the shift key, and scroll left or right until you have selected the text.
To select different items, such as messages, files, or contacts, scroll up, down, left or right to highlight the item you want to
select. Select Options > Mark/Unmark > Mark to select one item or Options > Mark/Unmark > Mark all to select all items.
To select an object (for example, an attachment in a document) scroll to the object so that square markers appear on each side
of the object.
Write text
Your device has a full keyboard. Most common punctuation marks either have a key of their own or they can be entered by
pressing a combination of keys.
,
and
indicate the selected case.
Some characters (for example, punctuation marks and symbols) are marked in blue color on the keys. To insert a character
marked in blue, press the blue function key, and the key that has the blue character you want.
To insert a number, press the blue function key so that is shown on the display, and a key with a number on the blue
background. To lock the blue function key and insert only numbers, press the blue function key twice so that
the display.
is shown on
To erase a character, press the backspace key. Press and hold the backspace key to clear more than one character.
To open a list of special characters, press the Chr key. Use the scroll key to scroll through the list and select a character.
© 2007 Nokia. All rights reserved.
16
B a s i c i n f o r m a t i o n a b o u t y o u r d e v i c e
To add characters by using other keys such as "A" or "O", press and hold the Chr key and simultaneously press the other key as
many times as is needed before the character you want is shown.
To switch between the different character cases, press the shift key, so that
is shown on the display.
Copy and paste text
1. To select letters and words, press and hold the shift key. At the same time, scroll in the direction necessary to highlight the
word, phrase, or line of text you want to copy. As the selection moves, the text is highlighted.
2. To copy the text to the clipboard, press Ctrl+C. To insert the text into a document, press Ctrl+V.
Change the writing language
When you write text, you can change the writing language. When you are writing and press Chr+a key several times to use a
specific character, changing the writing language gives you access to different characters.
For example, if you are writing a message using a non-Latin alphabet and want to add a person's name using Latin alphabets,
select Options > Writing language and a writing language that uses Latin characters.
Common actions in several applications
You can find the following actions in several applications:
To switch between open applications, press and hold the menu key to see a list of open applications. Select an application.
To change the profile or switch off or lock the device, press the power key briefly.
To save a file, select Options > Save. There are different save options depending on the application you use.
To send a file, select Options > Send. There are different send options depending on the application you use, such as e-mail or
multimedia messages and infrared or Bluetooth connectivity.
To print to a compatible printer, select Options > Printing options > Print. You can preview items that you want to print, or
edit the way printed pages look. Before you can print, you must define a compatible printer to your device. See
To delete a file, press the backspace key, or select Options > Delete.
Memory
There are two types of memory into which you can save data or install applications: device memory and removable memory.
Device memory
Memory that is built into your device is a dynamic memory pool shared by many applications. The amount of internal memory
available varies but cannot be increased past the maximum factory setting. Data stored on the device, such as software
applications, pictures, and music, consume device memory.
Removable memory
Removable memory is data storage that is not built into your device, such as a SIM card or a memory card. A SIM card stores
different information, such as information about the network operator and contacts. A memory card serves as external storage
media for software applications, pictures, music, contacts, text, or any other form of electronic data. High-capacity memory
cards are available.
Memory details
Select Menu, and Options > Memory details and Phone mem. or Memory card.
You can see how much memory is currently in use, how much free memory remains, and how much memory is consumed by
each data type. For example, you can see how much memory your e-mail messages, text documents, or calendar appointments
consume.
Tip: To ensure that you have adequate memory, you should regularly delete or transfer data to a memory card or PC.
Memory card
Your device supports memory cards of up to 2GB.
Your Nokia device supports the FAT16 and FAT32 file systems for memory cards. If you use a memory card from another device
or if you want to ensure compatibility of the memory card with your Nokia device, you may need to format the memory card
with your Nokia device. However, all data in the memory card is permanently deleted if you format the memory card.
© 2007 Nokia. All rights reserved.
17
B a s i c i n f o r m a t i o n a b o u t y o u r d e v i c e
Format a memory card
When a memory card is formatted, all data on the card is lost permanently. Consult your retailer to find out if you must format
the memory card before you can use it. To format a memory card, select Options > Format mem. card. When formatting is
complete, enter a name for the memory card.
Back up and restore to the memory card
It is recommended to back up device memory regularly to the memory card. The information can be restored to your device
later. To back up information from device memory to a memory card, select Menu > Tools > Memory > Options > Backup
phone mem.. To restore information from the memory card to the device memory, select Menu > Tools > Memory >
Options > Restore from card.
If you cannot use a memory card in your device, you may have the wrong type of memory card, the card may not be formatted
for your device, or the card has a corrupted file system.
Tip: You can insert and remove a memory card without removing the battery or switching off the device.
Unlock a memory card
To open a locked memory card, select Options > Unlock memory card. Enter the password.
Installing applications
You can use Nokia PC Suite to install applications. Nokia PC Suite transfers the installation file to your device, and the installation
starts automatically. You can also download an installation file from the web, in which case the installation may start
automatically. If the installation does not start automatically, locate and select the installation file on your device, and press
the scroll key.
Important: Your device can only support one antivirus application. Having more than one application with antivirus
functionality may affect performance and operation or cause the device to stop functioning.
Voice aid
Select Menu > Tools > Voice aid.
The voice aid application reads text on the screen, allowing you to use basic functions of your device without looking at the
display.
Select from the following:
•
•
•
•
•
Contacts — Hear the entries in your contacts list. Do not use this option if you have more than 500 contacts.
Recent calls — Hear information on your missed and received calls, dialed numbers, and frequent calls.
Voice mailbox — Retrieve and listen to your voice messages.
Dialler — Dial a telephone number.
Clock — Hear the current time and date.
To hear more options, select Options.
Hear your messages
Message reader readiness
Message reader reads your received text messages aloud. The application is available in your device in English. To download
Select Menu > Office > Msg. reader.
Select the text message you want to be read, and select Play. You can also activate Msg. reader by pressing and holding the left
selection key when you receive a text message. Message reader reads aloud the sender of the message and the message itself.
If the sender's number is not in your contacts, Message reader reads Message, from unrecognised number. while the number
is shown on the display.
To start reading the next message in your Inbox, scroll right. To start reading the previous message, scroll left.
To pause the reading, press the left selection key briefly. To continue, press the left selection key briefly again.
To end the reading, press the end key.
Speech
To edit the settings for the synthesized speech, select Menu > Tools > Speech.
Select from the following options:
•
•
Language — Set the language for the speech.
Voice — Set the voice for the speech. The voice is language dependent.
© 2007 Nokia. All rights reserved.
18
B a s i c i n f o r m a t i o n a b o u t y o u r d e v i c e
•
Voice settings — Adjust the voice properties.
Voice properties
To edit the voice properties for the synthesized speech, select Menu > Tools > Speech > Voice settings.
Select from the following options:
•
•
Speed — Select the desired speech rate.
Volume — Set the volume level for the speech.
Voice management
To manage the voices available for the selected language, select Menu > Tools > Speech, and scroll right.
Scroll to a voice, select Options and from the following:
•
•
•
Play voice — Listen to the selected voice.
Voice details — View information about the voice.
Delete — Delete the selected voice.
Profiles
Important: In the offline profile you cannot make or receive any calls, or use other features that require cellular network
coverage. Calls may still be possible to the official emergency number programmed into your device. To make calls,
you must first activate the phone function by changing profiles. If the device has been locked, enter the lock code.
Select Menu > Tools > Profiles.
You can adjust and customize the ringing tones, alert tones, and other device tones for different events, environments, or caller
groups.
To customize a profile, scroll to the desired profile in the list, and select Options > Personalise.
Define the following settings:
•
Ringing tone — Select a ringing tone from the list, or select Tone downloads to open a bookmark folder containing a list of
bookmarks for downloading tones using the browser. To listen to the selected tone, select Play. If you have two alternate
phone lines in use, you can specify a ringing tone for each line.
•
•
Video call tone — Select a ringing tone for video calls.
Say caller's name — Activate the text-to-speech ringing tone feature. When someone from your contacts list calls you, the
device sounds a ringing tone that is a combination of the spoken name of the contact and the selected ringing tone.
Ringing type — Select how you want the ringing tone to alert.
•
•
•
•
•
•
•
•
Ringing volume — Select the volume level of the ringing tone.
Message alert tone — Select a tone for received text messages.
E-mail alert tone — Select a tone for received e-mail messages.
Vibrating alert — Select whether you want the device to vibrate when you receive a call.
Keypad tones — Set the volume level of the device keypad tones.
Warning tones — Set the warning tones on or off.
Alert for — You can set the device to ring only upon calls from phone numbers that belong to a selected contact group. Phone
calls coming from outside that group have a silent alert.
•
Profile name — You can give a name to a new profile or rename an existing profile. The General and Offline profiles cannot
be renamed.
The Offline profile prevents your device from accidentally switching on, sending or receiving messages, or using Bluetooth;
it also closes any Internet connection that may be in operation when the profile is selected. The Offline profile does not
prevent you from establishing a wireless LAN connection at a later time, so comply with any applicable safety requirements
when establishing and using wireless LAN connections.
To change a profile, scroll to the desired profile in the list, and select Options > Activate. If you select the Offline profile, you
cannot send or receive messages or use WLAN to read your e-mails.
To create a new profile, select Options > Create new, and define the settings.
Select ringing tones
To set a ringing tone, scroll to a profile, and select Options > Personalise > Ringing tone. Select a ringing tone from the list or
select Tone downloads to open a bookmark folder containing a list of bookmarks for downloading tones using the browser.
Any downloaded tones are saved to Gallery.
To play the ringing tone for a selected contact group only, scroll to a profile, and select Options > Personalise > Alert for, and
select the desired group. Phone calls coming from outside that group have a silent alert.
To browse for a message tone, scroll to a profile and select Options > Personalise > Message alert tone.
To listen to the selected tone, select the tone from the list and wait for the tone to play.
© 2007 Nokia. All rights reserved.
19
B a s i c i n f o r m a t i o n a b o u t y o u r d e v i c e
Change enhancement settings
Scroll to an enhancement, and select Options > Open.
Change the default profile for the enhancement.
Themes
Select Menu > Tools > Themes.
You can change the look of the display of your device.
To change the look of the display, highlight the theme you want to use, and select Options > Apply.
To edit a theme, highlight the theme you want to edit, and select Options > Edit. Select Wallpaper to change the background
image in the standby modes, or Power saver to use a text or the date and time as a power saver that appears on the display
when no key presses have been made for a some time.
To download themes, you need to establish a network connection that allows you to download themes from Internet sources
that are compatible with your device.
To download a theme, select Theme downloads. Enter the link from which you want to download your theme. Once the theme
is downloaded you can preview, activate, or edit it.
To preview a theme, highlight the theme you want to preview, and select Options > Preview. Select Apply to start using the
new theme.
Search
Select Menu > Office > Search.
With Search, you can search for information in your contacts, notes, calendar appointments, to-do notes, e-mail messages,
multimedia messages, and text messages. You can also search for files by the file names in your device memory and memory
card.
1. Select the content types you want to search in. To remove the selection, select it again. To include all content types in your
search, select Select all. To remove all content types, select Unselect all.
2. Enter your search keywords or some part of the keywords. To include two words in your search, separate them with a space.
You will only find items that contain both keywords.
3. Select Search.
Tip: Wildcards may help you find items. In your search keyword, use ? to substitute a single character and * to substitute
zero or more characters. If you use the ? or * wildcard, you must add * to the beginning and end of a search keyword,
for example, *s?all* ("shall") or *dev*ment* ("development").
To view the search results from your previous search, select Options > Previous results.
Notification light
You can set the notification light on the cover of your device to blink when you have received a new message or when you have
missed a phone call.
To define the notification light settings, select Menu > Tools > Settings > Phone > Notification light.
To set the time how long you want the notification light to blink, scroll to Blink light for and press the scroll key. To select
whether you want to be notified of new short messages, multimedia messages, e-mail messages, and missed phone calls, scroll
to Notified events and press the scroll key.
© 2007 Nokia. All rights reserved.
20
3.
Transfer content between devices
You can transfer content, such as contacts, from a compatible Nokia device to your Nokia E61i using Bluetooth connectivity or
infrared. The type of content that can be transferred depends on the phone model. If the other device supports synchronization,
you can also synchronize data between the other device and your Nokia E61i.
Transfer data with Bluetooth or infrared
Tip: If you transfer data from your previous device, the device may require you to insert the SIM card. Your Nokia E61i
does not need a SIM card when transferring data.
To start transferring data from a compatible device, select Menu > Tools > Transfer > Transfer data.
Bluetooth connectivity
1. In the information view, select Continue.
2. Select Via Bluetooth. Both devices must support the selected connection type.
3. Activate Bluetooth in your other device, and select Continue in your Nokia E61i to start searching for devices with active
Bluetooth connectivity.
4. Select Stop in your Nokia E61i after it has found your other device.
5. Select your other device from the list. You are asked to enter a passcode (1 to 16 digits) on your Nokia E61i. The passcode is
used only once to confirm this connection.
6. Enter the code on your Nokia E61i, and select OK. Enter the passcode on your other device, and select OK. The devices are
now paired. See "Pair devices," p. 51.
For some phone models, the Transfer data application is sent to your other device as a message. To install Transfer data on
your other device, open the message, and follow the instructions on the display.
7. From your Nokia E61i, select the content you want to transfer from your other device, and OK.
Infrared connectivity
1. In the information view, select Continue.
2. Select Via infrared. Both devices must support the selected connection type.
4. From your Nokia E61i, select the content you want to transfer from your other device, and OK.
Content is copied from the memory of the other device to the corresponding location in your device. Copying time depends on
the amount of data to be transferred. You can also cancel and continue later.
The necessary steps for data transfer may vary depending on your device, and whether you have interrupted data transfer
earlier. The items that you can transfer vary depending on the other device.
Synchronize data with another device
If you have previously transferred data to your Nokia E61i, and your other device supports synchronization, you can use
Transfer to keep the data of the two devices up to date.
1. Select Phones, and press the scroll key.
2. Scroll to the device from which you transferred data, and press the scroll key.
3. Select Synchronise, and press the scroll key. The devices start synchronizing using the same connection type that you selected
when you originally transferred data. Only the data that you originally selected for data transfer is synchronized.
To modify the data transfer and synchronization settings, select Synchronise, scroll to a device, press the scroll key, and select
Edit.
© 2007 Nokia. All rights reserved.
21
4.
Messages
Select Menu > Messag..
In Messaging (network service), you can send and receive text messages, multimedia messages, and e-mail messages. You can
also receive web service messages, cell broadcast messages, and special messages containing data, and send service commands.
Before sending or receiving messages, you may need to do the following:
•
•
•
•
•
•
Insert a valid SIM card in the device and be located in a service area of the cellular network.
Verify that the network supports the messaging features you want to use and that they are activated on your SIM card.
Define Internet access point (IAP) settings on the device. See "Access points," p. 81.
Define e-mail account settings on the device. See "E-mail account settings," p. 33.
Define SMS settings on the device. See "Text message settings," p. 32.
Define MMS settings on the device. See "Multimedia message settings," p. 32.
The device may recognize the SIM card provider and automatically configure some of the message settings. If not, you may need
to define the settings manually, or contact your service provider, network operator, or Internet service provider to configure
the settings.
The Messag. application displays each type of messaging folder in a list format with the newest message displayed first in each
folder.
Select one of the following:
•
•
•
•
•
•
•
•
New message — Create and send a new text, multimedia, or e-mail message.
Inbox — View received messages, except e-mails and cell broadcast messages.
My folders — Create your own folders to store messages and templates.
Mailbox — View and reply to received e-mail.
Drafts — Store messages that have not been sent.
Sent — Store messages that have been sent.
Outbox — View messages waiting to be sent.
Reports — View information about the delivery of sent messages.
Organize messages
To create a new folder to organize your messages, select My folders > Options > New folder. Enter the folder name, and select
OK.
To rename a folder, select the folder and Options > Rename folder. Enter the new folder name, and select OK. You can only
rename folders that you have created.
To move a message to another folder, open the message, and select Options > Move to folder, the folder, and OK.
To sort messages in a specific order, select Options > Sort by. You can sort the messages by Date, Sender, Subject, or Message
type.
To view the properties of a message, select the message and Options > Message details.
Search for messages
To search for a message, open the folder in which you want to search, select Options > Find. Enter the search term, and select
OK.
Text message center settings
Select Options > Settings > Text message > Message centres.
To edit message centers, select the message center, and Options > Edit.
To add new message centers, select Options > New msg. centre.
To delete message centers, select the message center, and press the backspace key.
E-mail messages
To receive and send mail, you must have a remote mailbox service. This service may be offered by an Internet service provider,
a network service provider, or your company. Your device is compliant with Internet standards IMAP4 (revision 1) and POP3,
and a range of e-mail solutions. Other e-mail providers may offer services with different settings or features than those described
here.
Before you can send, receive, retrieve, reply to, and forward mail on your device, you must also do the following:
© 2007 Nokia. All rights reserved.
22
M e s s a g e s
•
•
Configure an Internet access point (IAP). Access points may already be configured in your device. See "Access
Set up an e-mail account, and define the e-mail settings correctly. Depending on your device, you can use the mailbox guide,
settings wizard, or define the settings manually.
Follow the instructions from your remote mailbox and Internet service providers. Contact your network and Internet service
providers or operator for the correct settings.
Set up your e-mail with the mailbox guide
If you select Mailbox in the messaging main view and have not set up your e-mail account, you are prompted to do so. To start
setting up the e-mail account with the mailbox guide, select Yes.
1. To start entering the e-mail settings, select Start.
2. In Mailbox type, select IMAP4 or POP3, and select Next.
Tip: POP3 is a version of the post office protocol that is used to store and retrieve e-mail or Internet mail messages.
IMAP4 is a version of the Internet message access protocol that lets you access and manage e-mail messages while
the messages are still on the e-mail server. You can then choose which messages to download to your device.
3. In My e-mail address, enter your e-mail address. Select Next.
4. In Incoming mail serv., enter the name of the remote server that receives your e-mail, and select Next.
5. In Outgoing mail serv., enter the name of the remote server that sends your e-mail, and select Next. Depending on your
mobile operator, you might have to use your mobile operator's outgoing mail server instead of your e-mail provider's.
6. In Access point, select the Internet access point your device should use when it retrieves the e-mails. If you select Always
ask, each time the device starts to retrieve e-mail, it asks which Internet access point it should use, but if you select an access
point, the device makes the connection automatically. Select Next.
Tip: If you select Select group, the device makes the connection automatically using the best available Internet
access point from the access point group. Select the access point group and Back to save the selection.
7. Enter a name for your new mailbox, and select Finish.
When you create a new mailbox, the name you give to the mailbox replaces Mailbox in the Messag. main view.
Select your default mailbox
If you have defined several mailboxes, you can select one of them as your default mailbox. To define the default mailbox, select
Options > Settings > E-mail > Default mailbox and the mailbox.
If you have defined several mailboxes, you must select the mailbox that you want to use every time you start composing a new
e-mail message.
Configure the e-mail key
Your device has an e-mail key. With the e-mail key, you can access your default e-mail inbox or open your default e-mail editor
from the active standby. The functionality depends also on your mailbox service provider.
To configure the e-mail key, select Menu > Tools > E-mail key. Select the e-mail account that you want to use with the e-mail
key.
Connect to mailbox
E-mail addressed to you is not automatically received by your device, but by your remote mailbox. To read your e-mail, you must
first connect to the remote mailbox and retrieve the e-mails to your device.
To retrieve received e-mail messages to your device, select your mailbox in the Messag. main view. When the device asks Connect
to mailbox?, select Yes.
To view e-mail messages in a folder, scroll to the folder, and press the scroll key. Scroll to a message, and press the scroll key.
To retrieve e-mail messages to your device, select Options > Retrieve e-mail > New to retrieve new messages that you have
neither read nor retrieved, Selected to retrieve only messages you select from the remote mailbox, or All to retrieve all messages
not previously retrieved. If you retrieve HTML formatted e-mails to your device, the formatting in the e-mails may be lost.
To disconnect from a remote mailbox, select Options > Disconnect.
View e-mail offline
Working offline means that your device is not connected to a remote mailbox. Managing your e-mail offline enables you to save
in connection costs and work in conditions that do not allow a data connection. Any changes you make in the remote mailbox
folders while offline take effect in your remote mailbox the next time you go online and synchronize. For example, if you delete
an e-mail from your device when offline, the e-mail is deleted from the remote mailbox the next time you connect to the mailbox.
© 2007 Nokia. All rights reserved.
23
M e s s a g e s
1. Select Messag. > Options > Settings > E-mail. Select the e-mail account, and press the scroll key. Select Retrieval
settings > E-mail to retrieve > Msgs. & attachs. to retrieve entire messages with their attachments to your device.
2. Open your mailbox, and select Options > Retrieve e-mail. Select New to retrieve new messages that you have neither read
nor retrieved, Selected to retrieve only messages you select from the remote mailbox, or All to retrieve all messages not
previously retrieved. The device goes online and connects to the mailbox to retrieve the mails.
3. After retrieving the e-mails, select Options > Disconnect to return to the offline mode.
4. To view an e-mail message, scroll to it, and press the scroll key.
Some options require you to connect to your remote mailbox.
Tip: To subscribe to other folders in your remote mailbox, select E-mail settings > Retrieval settings > Folder
subscriptions. E-mail in all subscribed folders is updated when you retrieve e-mail from your remote mailbox.
Read and reply to e-mail
Important: Exercise caution when opening messages. E-mail messages may contain malicious software or otherwise
be harmful to your device or PC.
To read a received e-mail, scroll to the e-mail, and press the scroll key.
To search for an e-mail in your mailbox, select Options > Find. Enter the search term, and select OK.
To open an attachment, select Options > Attachments. Scroll to the attachment, and press the scroll key.
To reply only to the sender of an e-mail, open the e-mail, and select Options > Reply > To sender.
To reply to all recipients of an e-mail, open the e-mail, and select Options > Reply > To all.
Tip: If you reply to an e-mail that contains attached files, the attachments are not included in the reply. If you forward
the received e-mail, attachments are included.
To delete an attachment from an e-mail that you are sending, select the attachment and Options > Remove.
To set the message priority, select Options > Sending options > Priority and from the available options.
To call the sender of the e-mail, open the e-mail, and scroll up to the sender. Select Options > Call.
To reply to the sender of the e-mail with a text message or multimedia message, open the e-mail, and scroll up to the sender.
Select Options > Create message.
To forward an e-mail, open the e-mail, and select Options > Forward.
Delete messages
To free up memory space on your device, regularly delete messages from the Inbox and Sent folders, and delete retrieved e-
mail messages.
To delete a message, scroll to it, and press the backspace key.
You can select to delete local e-mail messages on the device and keep the original on the server, or you can delete both the
local e-mail messages on the device and the original messages on the server.
To delete e-mails from the device only, select Options > Delete > Phone (header remains).
To delete e-mail both from the device and from the remote server, open an e-mail, and select Options > Delete > Phone and
server.
E-mail folders
If you create subfolders in your IMAP4 mailboxes on a remote server, you can view and manage these folders with your device.
You can only subscribe to folders in your IMAP4 mailboxes. Subscribing to folders in a remote mailbox allows you to view those
folders on your device.
To view folders in your IMAP4 mailbox, establish a connection, and select Options > E-mail sett. > Retrieval settings > Folder
subscriptions.
To view a remote folder, select a folder and Options > Subscribe. Every time you go online, the subscribed folders are updated.
This may take some time if the folders are large.
To update the list of folders, select a folder and Options > Update folder list.
Write and send e-mail
To write an e-mail, select Options > Add recipient to select the recipients' e-mail addresses from the contacts list, or enter the
e-mail addresses in the To field. Use a semicolon to separate entries. Scroll down, and use the Cc field to copy other recipients,
© 2007 Nokia. All rights reserved.
24
M e s s a g e s
or the Bcc field to blind copy recipients. In the Subject field, enter the subject of the e-mail. Enter your e-mail message in the
text area, and select Options > Send.
To attach a file to an e-mail, select Options > Insert and the attachment you want to add. You can insert images, sound clips,
notes, and other files, such as office files.
To set the sending time for an e-mail message, select Options > Sending options > Send message. Select Immediately or When
conn. avail. if you are working offline.
E-mail messages are stored in the Outbox before sending. Unless the e-mail is sent immediately, you can open the Outbox and
suspend and resume sending or view the e-mail.
Text messages
Your device supports the sending of text messages beyond the character limit for a single message. Longer messages are sent
as a series of two or more messages. Your service provider may charge accordingly. Characters that use accents or other marks,
and characters from some language options, take up more space, limiting the number of characters that can be sent in a single
message.
Write and send text messages
Select Menu > Messag. > New message > Text message.
1. In the To field, press the scroll key to select recipients from Contacts, or enter the recipients' mobile phone numbers manually.
If you enter more than one number, separate the numbers with a semicolon.
2. Enter the text of the message. To use a template, select Options > Insert > Template.
3. Select Options > Send to send the message.
Sending options for text messages
To set sending options for the text message, select Options > Sending options.
Define the following:
•
•
Msg. centre in use — Select a message center to send the message.
Character encoding — Select Reduced support to use automatic character conversion to another encoding system when
available.
•
•
Receive report — Select Yes if you want that the network sends you delivery reports on your messages (network service).
Message validity — Select how long the message center resends your message if the first attempt fails (network service). If
the recipient cannot be reached within the validity period, the message is deleted from the message center.
Message sent as — Convert the message to another format, such as Text, Fax, Paging or E-mail. Change this option only if you
are sure that your message center is able to convert text messages into these other formats. Contact your network operator.
Reply via same ctr. — Select whether you want the reply message to be sent using the same text message center number
(network service).
•
•
Reply to received text messages
To reply to a text message, open the message from the Inbox. Select Options > Reply. Enter the text of the message, and select
Options > Send.
To call the sender of a text message, open the message from the Inbox, and select Options > Call.
Text messages on the SIM card
Text messages may be stored on your SIM card. Before you can view SIM messages, you must copy the messages to a folder in
the device. After copying the messages to a folder, you can view them in the folder or delete them from the SIM card.
Select Options > SIM messages.
1. Select Options > Mark/Unmark > Mark or Mark all to mark every message.
2. Select Options > Copy.
3. Select a folder and OK to begin copying.
To view SIM card messages, open the folder where you copied the messages, and open a message.
To delete a text message from the SIM card, select the message, and press the backspace key.
Picture messages
Note: The picture message function can be used only if it is supported by your service provider. Only compatible devices
that offer picture message features can receive and display picture messages. The appearance of a message may vary
depending on the receiving device.
© 2007 Nokia. All rights reserved.
25
M e s s a g e s
Select Menu > Messag..
To view a picture message, open the message from the Inbox folder.
Select Options and select from the following:
•
•
•
•
Message details — View information about the message.
Move to folder — Save the message in a different folder.
Add to Contacts — Add the sender of the message to your contacts.
Find — Find phone numbers and addresses that the message may contain.
Forward picture messages
1. In the Inbox, open a picture message and select Options > Forward.
2. In the To field, enter a recipient's number, or press the scroll key to add a recipient from Contacts. If you enter more than
one number, separate the numbers with a semicolon.
3. Enter the text of your message. The text can have 120 characters. To use a template, select Options > Insert > Template.
4. To send the message, press the call key.
Tip: To remove the picture from the message, select Options > Remove picture.
Multimedia messages
A multimedia message (MMS) can contain text and objects such as images, sound clips, or video clips.
Only devices that have compatible features can receive and display multimedia messages. The appearance of a message may
vary depending on the receiving device.
Before you can send or receive multimedia messages on your device, you must define the multimedia message settings. Your
device may have recognized the SIM card provider and automatically configured the multimedia message settings. If not, contact
your service provider. See "Multimedia message settings," p. 32.
Create and send multimedia messages
Select New message > Multimedia message.
1. In the To field, press the scroll key to select recipients from Contacts, or enter the recipients' mobile phone numbers or e-
mail addresses manually.
2. In the Subject field, enter a subject for the message. To change the fields that are visible, select Options > Address fields.
3. Enter the text of the message, and select Options > Insert object to add media objects. You can add objects such as Image,
Sound clip, or Video clip.
The wireless network may limit the size of MMS messages. If the inserted picture exceeds this limit, the device may make it
smaller so that it can be sent by MMS.
4. Each slide of your message can contain only one video or audio clip. To add more slides to your message, select Options >
Insert new > Slide. To change the order of slides in your message, select Options > Move.
5. To preview a multimedia message before sending it, select Options > Preview.
6. Press the scroll key to send the multimedia message.
Tip: You can also create multimedia messages directly from several applications, such as Contacts and Gallery.
To delete an object from a multimedia message, select Options > Remove.
Sending options for multimedia messages
Select Options > Sending options and from the following options:
•
Receive report — Select Yes if you want to receive a notification when the message has been successfully delivered to the
recipient. Receiving a delivery report of a multimedia message that has been sent to an e-mail address may not be possible.
Message validity — Select how long the messaging center tries to send the message. If the recipient of a message cannot be
reachedwithinthevalidityperiod, themessageisremovedfromthemultimediamessagingcenter. Thenetworkmustsupport
this feature. Maximum time is the maximum amount of time allowed by the network.
•
Create presentations
Select New message > Multimedia message.
1. In the To field, press the scroll key to select recipients from Contacts, or enter the recipients' mobile phone numbers or e-
mail addresses manually.
2. Select Options > Create presentation and a presentation template.
© 2007 Nokia. All rights reserved.
26
M e s s a g e s
Tip: A template may define which media objects you can include in the presentation, where they appear, and which
effects are displayed between images and slides.
3. Scroll to a text area and enter the text.
4. To insert images, sound, video, or notes in your presentation, scroll to the corresponding object area, and select Options >
Insert.
Tip: To move between object areas, scroll up and down.
5. To add slides, select Insert > New slide.
6. Select Options and from the following:
•
Preview — See what your multimedia presentation looks like when it is opened. Multimedia presentations may only be
viewed in compatible devices that support presentations. They may appear different in different devices.
Backgrnd. settings — Select the background color for the presentation and background images for different slides.
Effect settings — Select effects between images or slides.
•
•
Creating multimedia presentations is not possible if MMS creation mode is Restricted. To change MMS creation mode, select
Messag. > Options > Settings > Multimedia message.
The available options may vary.
To send your multimedia presentation, press the scroll key.
Tip: To save the message in Drafts without sending it, select Done.
Receive and reply to multimedia messages
Important: Exercise caution when opening messages. Multimedia message objects may contain malicious software
or otherwise be harmful to your device or PC.
Before you can send or receive multimedia messages on your device, you must define the multimedia message settings. Your
device may have recognized the SIM card provider and automatically configured the multimedia message settings. If not, contact
your service provider. See "Multimedia message settings," p. 32.
If you receive multimedia messages containing objects unsupported by your device, you cannot open them.
1. To reply to a multimedia message, open the message from the Inbox, and select Options > Reply.
2. Select Options > To sender to reply to the sender with a multimedia message or Options > Via text message to reply to the
sender with a text message.
Tip: To add recipients to your reply, select Options > Add recipient to select the recipients of the message from the
contacts list, or enter the recipients' phone numbers or e-mail addresses manually in the To field.
3. Enter the text of the message, and press the scroll key to send it.
View presentations
Open the Inbox, scroll to a multimedia message that contains a presentation, and press the scroll key. Scroll to the presentation,
and press the scroll key.
To pause the presentation, press either selection key below the display.
After you pause the presentation or playing finishes, select Options and from the following:
•
•
•
•
•
Open link — Open a Web link and browse the Web page.
Activate scrolling — Scroll text or images too large to fit on the display.
Continue — Resume playing the presentation.
Play — Replay the presentation from the start.
Find — Find phone numbers and e-mail or Web addresses the presentation may contain. You may use these numbers and
addresses to make calls, send messages, or create bookmarks, for example.
The available options may vary.
View media objects
Open the Inbox, scroll to a received multimedia message and press the scroll key. Select Options > Objects.
To view or play a media object, scroll to it, and press the scroll key.
Media objects and message attachments may contain viruses or other harmful software. Do not open any objects or attachments
unless you are sure of the trustworthiness of the sender.
To save a media object in its corresponding application, scroll to the object, and select Options > Save.
To send a media object to compatible devices, scroll to it, and select Options > Send.
© 2007 Nokia. All rights reserved.
27
M e s s a g e s
Tip: If you receive multimedia messages that contain media objects your device cannot open, you may be able to send
these objects to another device such as a computer.
View and save multimedia attachments
To view multimedia messages as complete presentations, open the message, and select Options > Play presentation.
Tip: If you have selected a multimedia object in a multimedia message, to view or play them, select View image, Play
sound clip, or Play video clip.
To view the name and size of an attachment, open the message, and select Options > Objects.
To save a multimedia object, select Options > Objects, the object, and Options > Save.
Instant messaging
Select Menu > Connect. > IM.
Instant messaging (IM) (network service) allows you to converse with other people using instant messages and join discussion
forums (IM groups) with specific topics. Various service providers maintain IM servers that you can log in to after you register
to an IM service. Service providers may differ in their support of features.
If IM is not available from your wireless service provider, it may not appear in the menu of your device. Contact your service
provider for more information about signing up for IM services and costs for services. For more information on the availability
of IM settings, contact your network operator, service provider, or dealer.
You may receive the settings in a special text message from the network operator or service provider that offers the IM service.
You must save the settings to access the service that you want to use. You can also enter the settings manually.
Connect to an IM server
To converse with an IM user or users, and to view and edit your IM contacts, you must log into the instant messaging server.
Open IM, and select Options > Login. Enter your user ID and password, and press the scroll key to log in. You can obtain the
user name, password, and other settings to log in from your service provider when you register for the service.
Tip: To have instant messaging connect to the server automatically when you open the application, select Options >
Settings > Server settings > IM login type > On app. start-up.
Search IM users or IM groups
To search for IM users and user IDs, select IM contacts > Options > New IM contact > Search. You can search by User's name,
User ID, Phone number, and E-mail address.
To search for IM groups and group IDs, select IM groups > Options > Search. You can search by Group name, Topic, and
Members (user ID).
Scroll to a found IM user or group, and select Options and from the following:
•
•
•
•
•
•
•
•
•
New search — Conduct another search.
More results — View the remaining found IM users or groups, if any.
Previous results — View the IM users or groups that were found in the previous search.
Open conversation — Start a conversation with the user if the user is online.
Add to IM contacts — Save the user in one of your IM contacts lists.
Send invitation — Invite the IM user to an IM group.
Blocking options — Prevent or allow the reception of messages from the IM user.
Join — Join the IM group.
Save — Save the group.
Conversations with a single IM user
The Conversations view shows a list of the individual conversation participants with whom you have an ongoing conversation.
Ongoing conversations are automatically closed when you exit IM.
To view a conversation, scroll to a participant, and press the scroll key.
To continue the conversation, enter your message, and press the scroll key.
To return to the conversations list without closing the conversation, select Back. To close the conversation, select Options >
End conversation.
To start a new conversation, select Options > New conversation. You can start a new conversation with a different contact
while you are inside another active conversation. However, you cannot have two active conversations with the same contact.
To insert an image to an instant message, select Options > Send image, and select the image you want to send.
© 2007 Nokia. All rights reserved.
28
M e s s a g e s
To save a conversation participant to your IM contacts, select Options > Add to IM contacts.
To save a conversation, while in the conversation view, select Options > Record chat. The conversation is saved as a text file
that can be opened and viewed in the Notes application.
To send automatic replies to incoming messages, select Options > Set auto reply on. You can still receive messages.
IM groups
The IM groups view shows a list of the IM groups that you have saved or to which you are currently joined.
IM groups is available only if you logged into an IM server when you opened the IM application, and the server supports IM
groups.
To create an IM group, select Options > Create new group.
To join an IM group or to continue a group conversation, scroll to the group, and press the scroll key. Enter a message, and press
the call key to send it.
To join an IM group that is not on the list, but for which you know the group ID, select Options > Join new group.
To leave the IM group, select Options > Leave IM group.
You can also select Options and from the following:
•
Group — Select Save to save the group to your IM groups, View participants to view the current members of the group, or
Settings to edit the group settings. You can only select this option if you have editing rights to the group.
Login — Connect to an instant messaging server if you did not log in when you opened the application.
Logout — Disconnect from the IM server.
•
•
•
Settings — Edit instant messaging application or server settings.
To remove an IM group, press the backspace key.
Group conversations
To join the conversation, select a group.
Select Options and from the following:
•
Insert smiley — Add a smiley in your message.
•
•
•
•
•
•
Send private msg. — Send a private message to one or several, but not all, members of the IM group.
Reply — Send a message only to the sender of the open message.
Forward — Forward the open message to another IM group or contact.
Send invitation — Invite an IM user to join the group.
Leave IM group — End instant messaging in the group.
Group — Select Save to save the group to your IM groups, View participants to view the current members of the group, or
Settings to edit the group settings. You can only select this option if you have editing rights to the group.
Record chat — Save a copy of the group conversation.
•
To send a message, enter the message, and press the call key.
IM group settings
Select IM groups > Options > Group > Settings.
You can only edit IM group settings if you have editing rights to that group.
Select from the following settings:
•
•
•
•
•
•
•
Group name: — Enter a name for the IM group.
Group ID — The group ID is created automatically and cannot be added or changed.
Group topic — Enter a topic for the group conversation.
Welcome note — Enter a note that greets IM users once they join the group.
Group size — Enter the maximum number of IM users that can join the group.
Allow search — Select whether you want to allow IM users to find the group when searching.
Editing rights — To provide other members of the group with editing rights to the group, select Selected > Options > Add
editor. IM users with editing rights can edit group settings and invite other users to join the group or ban them from it.
Group members — To close the group and allow only selected IM users to join it, select Selected only > Options > Add
member.
•
•
•
Banned list — To prevent some IM users from joining the group, select Options > Add to banned list.
Allow private msgs. — To prevent group members from sending private messages between themselves, select No.
Group editing rights
To add editing rights to or remove them from IM group members, scroll to the IM group, and select Options > Group >
Settings > Editing rights > Selected.
© 2007 Nokia. All rights reserved.
29
M e s s a g e s
Tip: IM users with editing rights can edit group settings and invite other users to join the group or ban them from the
group.
To provide members with editing rights to the group, select Options > Add editor and from the following:
•
•
From IM contacts — Add one or several of your IM contacts.
Enter user ID — Enter the ID of the IM user.
To remove editing rights from a group member, select Options > Remove.
Ban from groups
Scroll to the IM group, and select Options > Group > Settings > Banned list.
To prevent IM users from joining the group, select Options > Add to banned list and from the following:
•
•
From IM contacts — Ban one or several of your IM contacts.
Enter user ID — Enter the ID of the IM user.
To allow a banned user to join the group, select Options > Remove.
IM contacts
When login to an IM service is complete, your contact list for the service provider is retrieved automatically. If your contact list
is not available, wait a few minutes and try to retrieve your contacts list manually.
Tip: The online status of your IM contacts is shown by an indicator next to the contact name.
To create an IM contact card, select Options > New IM contact. Enter the user ID and a nickname, and select Done. The user ID
can be up to 50 characters, and the IM service provider may require the user ID to be in the [email protected] format.
The nickname is optional.
To view a different list of your IM contacts, select Options > Change contact list.
Scroll to an IM contact, select Options and from the following:
•
•
•
Open conversation — Start or continue instant messaging with the contact.
Contact details — View the contact card.
Editing options — Edit or delete the contact card, move it to another contact list, or receive a note when the contact's online
status changes.
•
•
•
•
•
•
•
Belongs to groups — See the IM groups the contact has joined.
New contact list — Create a contact list for a specific group of IM contacts.
Reload users' availab. — Update the online status of your IM contacts.
Blocking options — Prevent or allow the reception of messages from the contact.
Login — Connect to an instant messaging server if you did not log in when you opened the application.
Logout — Disconnect from the IM server.
Settings — Edit instant messaging application or server settings.
The available options may vary.
To delete an IM contact, press the backspace key.
Blocked contacts
Select IM contacts > Options > Blocking options > View blocked list.
To find a blocked IM user, enter the first letters of the user's name. Matching names appear in a list.
To allow receiving messages from a blocked IM user, select Options > Unblock.
To prevent receiving messages from other IM users, selectOptions > Block new contacts. Select the IM user from your IM contacts,
or enter the user ID.
View invitations
Select Conversations. Scroll to an invitation, and press the scroll key.
Select Options and from the following:
•
•
•
•
Join — Join the instant messaging group.
Reject — Reject the invitation and send a message to its sender.
Delete — Delete the invitation.
Blocking options — Prevent the reception of invitations from this sender.
Recorded messaging
To view a recorded conversation, select Record. chats, scroll to a conversation, and press the scroll key.
© 2007 Nokia. All rights reserved.
30
M e s s a g e s
You can also scroll to a recorded conversation, and select Options and select from the following:
•
•
Send — Send the IM session to a compatible device.
Login — Connect to an instant messaging server if you did not log in when you opened the application. To disconnect, select
Logout.
•
Settings — Edit instant messaging application or server settings.
To delete an IM conversation, press the backspace key.
Settings
Select Options > Settings > IM settings.
Select from the following settings:
•
•
Use screen name — To change the name that identifies you in IM groups, select Yes.
Allow messages from — Select to receive instant messages from all other IM users, your IM contacts only, or not to receive
messages at all.
•
Allow invitations from — Select to receive invitations to IM groups from all IM users, your IM contacts only, or not to receive
invitations at all.
•
•
•
•
Msg. scrolling speed — To decrease or increase the speed at which new messages are displayed, scroll left or right.
Sort IM contacts — Select to list your IM contacts alphabetically or by their online status.
Availabil. reloading — To update the online status of your IM contacts automatically, select Automatic.
Offline contacts — Select if IM contacts with an offline status are shown in the IM contacts list.
The settings available for editing may vary. Contact your service provider for more information.
IM server settings
Select Options > Settings > Server settings.
Scroll to the following options, and press the scroll key to configure your IM server:
•
•
Servers — Add new, edit, or delete servers.
Default server — Change the server to which your device automatically logs into, scroll to the desired server, and press the
scroll key.
•
IM login type — To establish a connection between your device and the default server automatically, select Automatic. Select
Auto. in home network to automate the connection when in your home network. Select On app. start-up to connect to the
server when you open the messaging application. Select Manual to connect to the server manually at any time.
Special messages
Your device can receive many kinds of messages that contain data:
•
•
•
Operator logo — To save the logo, select Options > Save.
Ringing tone — To save a ring tone, select Options > Save.
Configuration message — You may receive settings from your network operator, service provider, or company information
management department in a configuration message. To accept the settings, open the message, and select Options > Save
all.
•
E-mail notification — The note tells you how many new e-mails you have in your remote mailbox. An extended notification
may list more detailed information.
Send service commands
Send a service request message to your service provider and request activation for certain network services.
Tosendaservicerequesttoyourserviceprovider, selectOptions > Service command. Entertheservicerequestasatextmessage,
and select Options > Send.
Cell broadcast (network service)
With the cell broadcast service, you can receive messages on various topics from your service provider, such as weather or traffic
conditions in a particular region. For available topics and relevant topic numbers, contact your service provider.
Cell broadcast messages cannot be received in UMTS networks.
Messagescannotbe receivedwhenthe device isinRemote SIM mode. Apacketdata(GPRS)connectionmay preventcellbroadcast
reception.
Select Menu > Messag. > Options > Cell broadcast.
To receive cell broadcast messages, you must turn on cell broadcast reception. Select Options > Settings > Reception > On.
To view messages that are related to a topic, scroll to the topic, and press the scroll key.
To receive messages related to a topic, scroll to the topic, and select Options > Subscribe.
© 2007 Nokia. All rights reserved.
31
M e s s a g e s
Tip: You can set important topics as hot topics. Scroll to the topic, and select Options > Hotmark. While the device is
in the standby mode, you are notified when you receive a message related to a hot topic.
To cancel the reception of cell broadcast messages, select the language of received messages, and select whether to
automatically detect new cell broadcast topics, select Options > Settings.
To add, edit, or delete topics, select Options > Topic, and select Add manually, Add from index, Edit, Delete or Delete all.
To store a cell broadcast message in the device memory, select the message andOptions > Save. You can store up to 50 messages
in the device memory.
To find the numbers and addresses the cell broadcast message may contain, select Options > Find and Phone number, E-mail
address, or Web address. You can then call and send messages, open browser pages, or create bookmarks and contact cards.
To delete a message, press the backspace key.
Message settings
Fill in all fields marked with Must be defined or with a red asterisk.
Your device may recognize the SIM card provider and automatically configure the correct text message, multimedia message,
and GPRS settings. If not, contact your service provider for the correct settings, order the settings from your service provider in
a configuration message, or use the Settings wizard application.
Text message settings
Select Options > Settings > Text message.
Define the following:
•
•
•
Message centres — View the available message centers for your device.
Msg. centre in use — Select a message center to send the message.
Character encoding — Select Reduced support to use automatic character conversion to another encoding system when
available.
•
•
Receive report — Select Yes if you want the network to send you delivery reports on your messages (network service).
Message validity — Select the length of time that the message center continues to resend your message if the first attempt
fails (network service). If the recipient cannot be reached within the validity period, the message is deleted from the message
center.
•
Message sent as — Convert the message to another format, such as Text, Fax, Paging or E-mail. Change this option only if you
are sure that your message center is able to convert text messages into these other formats. Contact your network operator.
Preferred conn. — Select the preferred method of connection when sending text messages from your device.
Reply via same ctr. — Select whether you want the reply message to be sent using the same text message center number
(network service).
•
•
Multimedia message settings
Select Options > Settings > Multimedia message.
Define the following settings:
•
Image size — Select Small or Large to scale images in multimedia messages. Select Original to maintain the original image
size of multimedia messages.
•
MMS creation mode — Select Restricted to have your device prevent you from including content in multimedia messages that
may not be supported by the network or the receiving device. To receive warnings about including such content, select
Guided. To create a multimedia message with no restrictions on attachment type, select Free. If you select Restricted, creating
multimedia presentations is not possible.
•
•
Access point in use — Select the default access point to connect to the multimedia message center. You may not be able to
change the default access point if it is preset in your device by your service provider.
Multimedia retrieval — Select Always automatic to always receive multimedia messages automatically, Auto. in home
network to receive notification of a new multimedia message that you can retrieve from the message center (for example,
when you are traveling abroad and are outside your home network), Manual to retrieve multimedia messages from the
message center manually, or Off to prevent receipt of any multimedia messages.
•
•
•
Allow anon. msgs. — Select whether you want to receive messages from unknown senders.
Receive adverts — Select whether you want to receive messages defined as advertisements.
Receive report — Select Yes to have the status of the sent message to be shown in the log (network service). Receiving a
delivery report of a multimedia message that has been sent to an e-mail address may not be possible.
Deny report sending — Select Yes to not send delivery reports from your device for received multimedia messages.
Message validity — Select the length of time that the message center continues to resend your message if the first attempt
fails (network service). If the recipient of a message cannot be reached within the validity period, the message is removed
from the multimedia messaging center. Maximum time is the maximum amount of time allowed by the network.
•
•
© 2007 Nokia. All rights reserved.
32
M e s s a g e s
E-mail account settings
Select Menu > Messag. > Options > Settings > E-mail.
If you have not defined a mailbox yet, select Mailbox in use, and press the scroll key. The mailbox guide opens and helps you
set up your e-mail account.
If you have defined a mailbox, select the mailbox, and press the scroll key to edit the settings.
The settings available for editing may vary. Some settings may be preset by your service provider.
Settings for the received e-mail
Select Incoming e-mail and from the following settings:
•
•
•
•
•
•
User name — Enter the user name for the e-mail service.
Password — Enter the password for the e-mail service.
Incoming mail serv. — Enter the IP address or host name of the server that receives your e-mail.
Access point in use — Select the Internet access point that the device uses for retrieving the e-mail messages that you receive.
Mailbox name — Enter a name for the mailbox.
Mailbox type — Select the mailbox protocol that your remote mailbox service provider recommends. The options are POP3
and IMAP4. This setting can be selected only once and cannot be changed if you have saved or exited from the mailbox
settings. If you use the POP3 protocol, e-mail messages are not updated automatically when you are online. To see the latest
e-mail messages, you must disconnect and make a new connection to your mailbox.
Security (ports) — Select the security option used to increase the security of the connection.
Port — Define a port for connection.
•
•
•
APOP secure login (for POP3 only) — Use with the POP3 protocol to encrypt the sending of passwords to the remote e-mail
server while connecting to the mailbox.
Settings for sent e-mail
Select Outgoing e-mail and from the following settings:
•
My e-mail address — Enter the e-mail address given to you by your service provider. Replies to your messages are sent to
this address.
•
•
•
User name — Enter the user name for the e-mail service.
Password — Enter the password for the e-mail service.
Outgoing mail serv. — Enter the IP address or host name of the mail server that sends your e-mail. You may only be able to
use the outgoing server of your network operator. Contact your service provider for more information.
Access point in use — Select the Internet access point that the device uses for sending the e-mail messages that you send.
Security (ports) — Select the security option used to secure the connection to the remote mailbox.
Port — Define a port for connection.
•
•
•
User settings
Select User settings and from the following settings:
•
•
My name — Enter a name to appear before your e-mail address when you send e-mail.
Reply-to — Select whether you want replies to be redirected to a different address. Select On, and enter the e-mail address
to which you want to direct the replies. You can only enter one address.
•
•
•
Delete e-mails from — Select whether you want to delete the e-mails only from the device or from both the device and the
server. Select Always ask if you want to confirm from where the e-mail should be deleted every time you delete an e-mail.
Send message — Select to send the e-mail as soon as possible, to send it the next time you retrieve e-mail, or to store the e-
mail in the outbox, from where you can send it later.
Send copy to self — Select whether you want to save a copy of the e-mail to your remote mailbox and to the address defined
in My e-mail address in the settings for Outgoing e-mail.
•
•
Include signature — Select whether you want to attach a signature to your e-mail messages.
New e-mail alerts — Select whether you want to receive the new e-mail indications (a tone and a note) when new mail is
received to the mailbox.
•
Flash on new e-mails — Select how long you want the notification light to blink when you receive a new e-mail, or whether
you want the notification light to blink at all.
Retrieval settings
Select Retrieval settings and from the following settings:
•
E-mail to retrieve (for POP3 mailboxes only) — Select whether you want to retrieve only the e-mail header information such
as sender, subject and date, e-mail, or e-mail with attachments.
•
•
•
Retrieval amount — Select the number of e-mails you want to retrieve from the remote server to your mailbox.
IMAP4 folder path (for IMAP4 mailboxes only) — Define the folder path for folders to be subscribed.
Folder subscriptions (for IMAP4 mailboxes only) — Subscribe to other folders in the remote mailbox and retrieve content
from those folders.
© 2007 Nokia. All rights reserved.
33
M e s s a g e s
Automatic retrieval settings
Select Automatic retrieval and from the following settings:
•
Header retrieval — Select whether you want to receive notifications when new e-mail is received in your remote mailbox.
Select Always enabled to always automatically retrieve new e-mail messages from your remote mailbox, or Only in home
net. to automatically retrieve new e-mail messages from your remote mailbox only when you are in your home network and
not, for example, traveling.
•
•
•
Retrieval days — Select the days on which e-mails are retrieved to your device.
Retrieval hours — Define the hours between which the e-mails are retrieved.
Retrieval interval — Select the time interval between retrieving new e-mails.
Cell broadcast settings
Select Menu > Messag. > Options > Settings > Cell broadcast.
Select from the following:
•
•
•
Reception — Select On to receive cell broadcast messages.
Language — Select the languages in which you want to receive cell broadcast messages.
Topic detection — Select On to display new topics in the cell broadcast topics list.
Other settings
Select Menu > Messag. > Options > Settings > Other.
Select from the following:
•
•
Save sent messages — Select whether to store sent messages in the Sent folder.
No. of saved msgs. — Enter the number of sent messages that you want to save. When the limit is reached, the oldest message
is deleted.
•
•
Folder view — Define whether you want the list of messages in the folders to be shown on one row or two rows.
Memory in use — Select where to save your received messages. You can save messages to memory card only if a memory
card is inserted.
The settings available for editing may vary.
© 2007 Nokia. All rights reserved.
34
5.
Telephone
When the device is locked, calls may be possible to the official emergency number programmed into your device.
To make and receive calls (network service), the device must be switched on, the device must have a valid SIM card installed,
and you must be located in a service area of the cellular network. The GPRS connection is put on hold during voice calls unless
the network supports dual transfer mode or you have a USIM card and are within the coverage of a UMTS network.
Make a call
Important: If the device has been locked, enter the lock code to activate the phone function. When the device is locked,
calls may be possible to the official emergency number. Making an emergency call in the offline profile or when the
device is locked requires that the device recognize the number to be an official emergency number. It is advisable to
change the profile or unlock the device by entering the lock code before you make the emergency call.
Enter the phone number, including the area code, and press the call key. If you enter an incorrect character, press the backspace
key. To end the call or cancel the call attempt, press the end key.
To make a call using the saved contacts, press the contacts key. Enter the first letters of the name, scroll to the name, and press
the call key. See "Contacts," p. 43.
Press the call key to view up to 20 numbers that you last called or attempted to call. Scroll to the desired number or name, and
press the call key to dial the number. See "Log," p. 41.
Use the volume keys to adjust the volume of an active call.
To call your voice mailbox (network service) in standby mode, press and hold 1, or press 1 then the call key.
Speed dial
Speed dialing allows you to make a call by pressing and holding a number key.
Before using speed dialing, select Menu > Tools > Settings > Call > Speed dialling > On.
To assign a number key to a phone number, select Menu > Tools > Spd. dial. Scroll to the number key (2 - 9) on the screen,
and select Options > Assign. Select the desired number from the Contacts directory.
To remove the phone number assigned to a number key, scroll to the speed dialing key, and select Options > Remove.
To change a phone number assigned to a number key, scroll to the speed dialing key, and select Options > Change.
Answer a call
To answer a call, press the call key.
To reject the call, press the end key.
To mute a ringing tone instead of answering a call, select Silence.
To answer a new call during a call when the Call waiting function is activated, press the call key. The first call is put on hold. To
end the active call, press the end key.
Options during a call
Select Options for the following options during a call:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Mute — Your voice cannot be heard by the other parties of a call while you listen to the active conversation.
Unmute — Your voice can be heard again by the other parties of the call.
Drop participant — Drop a party from the active call.
End active call — End the currently active call.
Menu — View the applications menu of your device.
Hold — Place the active call on hold.
Unhold — Remove the active call from hold.
New call — Place a new call while on a call, if conference calling (network service) is available.
Answer — Answer an incoming call while on a call, if Call waiting is activated.
Reject — Reject an incoming call while on a call, if Call waiting is activated.
Lock keypad — Lock the device keypad while on a call.
Conference — Merge an active and a held call into a conference call (network service).
Private — Converse privately with a selected participant during a conference call (network service).
Swap — Alternate between an active and a held call (network service).
Send DTMF — Send DTMF (dual tone multi-frequency) tone strings, for example, passwords. Enter the DTMF string or search
for it in Contacts, and select DTMF.
© 2007 Nokia. All rights reserved.
35
T e l e p h o n e
•
Transfer — Connect the held call to the active call and disconnect yourself from the call (network service).
The available options may vary.
Divert calls
Select Menu > Tools > Settings > Call divert.
Divert incoming calls to your voice mailbox or to another phone number. For details, contact your service provider.
1. Select a call type from the following:
•
•
•
Voice calls — Incoming voice calls.
Data and video calls — Incoming data and video calls.
Fax calls — Incoming fax calls.
2. Select one of the following call diverting options:
•
•
•
All voice calls, All data and vid. calls, or All fax calls. — Divert all incoming voice, data and video, or fax calls.
If busy — Divert incoming calls when you have an active call.
If not answered — Divert incoming calls after your device rings for a specified period of time. Define the time you let the
device ring before diverting the call in the Delay time: field.
•
•
If out of reach — Divert calls when the device is switched off or out of network coverage.
If not available — Activate the last three settings at the same time. This option diverts calls if your device is busy, not
answered, or out of reach.
3. Select Activate.
To check the current diverting status, scroll to the diverting option, and select Options > Check status.
To stop diverting voice calls, scroll to the diverting option, and select Options > Cancel.
Call barring
Call barring and call diverting cannot be active at the same time.
When calls are barred, calls may be possible to certain official emergency numbers.
Select Menu > Tools > Settings > Call barring.
You can bar the calls that can be made or received with the device (network service). To change the settings, you need the
barring password from your service provider. Call barring affects all calls, including data calls.
To bar calls, select Cellular call barring and select from the following options:
•
•
•
•
•
Outgoing calls — Prevent making voice calls with your device.
Incoming calls — Bar incoming calls.
International calls — Prevent calling to foreign countries or regions.
Incoming if abroad — Bar incoming calls when outside your home country.
Intern. except home — Prevent calls to foreign countries or regions, but allow calls to your home country.
To check the status of voice call barrings, scroll to the barring option, and select Options > Check status.
To stop all voice call barrings, scroll to a barring option, and select Options > Cancel all barrings.
Net call barring
To bar net calls, select Menu > Tools > Settings > Call barring > Internet call barring.
To reject net calls from anonymous callers, select Anonymous calls > On.
Send DTMF tones
You can send dual tone multi-frequency (DTMF) tones during an active call to control your voice mailbox or other automated
phone services.
To send a DTMF tone sequence, make a call, and wait until the other end answers. Select Options > Send DTMF. Type the DTMF
tone sequence, or select a predefined sequence.
To attach DTMF tone sequences to contact cards, press the contacts key. Open a contact, and select Options > Edit > Options >
Add detail > DTMF. Enter the tone sequence. To enter a pause of about 2 seconds before or between DTMF tones, press p. To
set the device to send the DTMF tones only after you select Send DTMF during a call, press w. Select Done.
Video calls
To be able to make a video call, you must be within coverage of a UMTS network. For availability of and subscription to video
call services, contact your network operator or service provider. While talking, you can send a real-time video to the recipient's
© 2007 Nokia. All rights reserved.
36
T e l e p h o n e
compatible mobile phone and see a real-time video sent by the recipient, if the recipient has a compatible mobile phone with
a video camera. A video call can only be made between two parties.
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely
loud.
To make a video call, enter the phone number or select the recipient of the call from Contacts, and select Options > Call >
Video call. You cannot convert the video call to a normal voice call.
To answer a video call, press the call key. If Allow video image to be sent to caller? is shown on the display, select Yes to send a
video to the caller or No to disable video sending.
Tip: In case you do not want to send a video during video calls, you can send a still image instead. Select the still image
to be sent in Menu > Tools > Settings > Call > Image in video call > Use selected.
During the call, select Options and from the following:
•
•
•
•
Audio — Talk to the recipient of the call.
Use video — See video without audio.
Loudsp. — Select to use the loudspeaker for receiving audio.
Handset — Mute the loudspeaker and use the handset.
Push to talk
Your service provider may have requested that certain features be disabled or not activated in your device. If so, they will not
appear on your device menu. Your device may also have been specially configured. This configuration may include changes in
menu names, menu order, and icons. Contact your service provider for more information.
Select Menu > Connect. > PTT.
Push to talk (PTT) (network service) provides direct voice communication connected with the push of a key. With push to talk,
you can use your device as you would use a walkie-talkie.
You can use push to talk to have a conversation with one person or with a group of people, or to join a channel. A channel is
like a chat room: you can call the channel to see if anyone is online. The channel call does not alert the other participants; the
participants just join the channel and start speaking with each other.
In push to talk communication, one person talks while the other participants listen through the built-in loudspeaker. Participants
take turns responding to each other. Because only one participant can talk at a time, the maximum duration of a speech turn
is limited. For details of the speech turn duration for your network, contact your network operator or service provider.
Remember to hold the device in front of you during a push to talk call so you can see the display. Speak towards the microphone,
and do not cover the loudspeaker with your hands.
Phone calls always take priority over push to talk.
Before you can use push to talk, you must define the push to talk access point and push to talk settings. You may receive the
settings in a special text message from the service provider that offers the push to talk service.
User settings
Select Options > Settings > User settings.
Define the following:
•
Incoming PTT calls — Select Notify if you want to see a notification of incoming calls. Select Auto-accept if you want push to
talk calls to be answered automatically. Select Not allowed if you want push to talk calls to be rejected automatically.
PTT call alert tone — Select Set by profile if you want the incoming call alert setting for push to talk to follow your profile
settings. If your profile is silent, you are not available to others using push to talk, except for callback requests.
Callback request tone — Define the ringing tone for callback requests.
•
•
•
•
•
Application start-up — Select if you want to log in to the push to talk service when you switch on your device.
Default nickname — Enter your default nickname (20 characters maximum) that is displayed to other users.
Show my PTT address — Define if you want callers to see your push to talk address. You can let all callers see the address,
show the address only to one-to-one callers or channel participants, or hide the address from all callers.
Show my login status — Define whether your login to the push to talk server is shown or hidden from other users.
•
Connection settings
Select Options > Settings > Connection settings.
Define the following:
•
•
•
•
•
Domain — Enter the domain name obtained from your service provider.
Access point name — Select the push to talk access point.
Server address — Enter the IP address or domain name of the push to talk server obtained from your service provider.
User name — Enter your user name obtained from your service provider.
Password — Enter a password, if required, to log into the push to talk service. The password is provided by the service provider.
© 2007 Nokia. All rights reserved.
37
T e l e p h o n e
Log in to push to talk service
If you have set Application start-up on in User settings, push to talk automatically logs in to the service when started. If not, you
must log in manually.
To log in to a push to talk service, select Options > Settings > Connection settings, and enter your User name, Password,
Domain, Server address, and Access point name. Select Options > Switch PTT on.
When the Ringing type setting of your device is set to Beep once or Silent, or there is an ongoing phone call, you cannot make
or receive push to talk calls.
Push to talk calls
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely
loud.
Select Options > PTT contacts.
To make a push to talk call, select one or several contacts from the list, and press the voice key. Remember to hold the device
in front of you during a push to talk call so you can see the display. The display informs you when it is your turn to speak. Speak
towards the microphone, and do not cover the loudspeaker with your hands. Press and hold the voice key the entire time you
are talking. When you have finished talking, release the key.
To end the push to talk call, press the end key.
When you receive a push to talk call, press the call key to answer the call or the end key to dismiss the call.
Callback requests
To send a callback request, select Options > PTT contacts, scroll to the desired contact, and select Options > Send callback
request.
To answer a callback request, select Show to open the callback request. To make a push to talk call to the sender, press the voice
key.
Contacts view
To view, add, modify, delete, or call contacts, select Options > PTT contacts. A list of names from the Contacts of your device is
displayed with information about their login status.
To call a selected contact, select Options > Talk 1 to 1. To make a group call, select Options > Make PTT group call.
To send the contact a request to call you, select Options > Send callback request.
Create a channel
A channel is like a chat room: you can call the channel to see if anyone is online. The channel call does not alert the other
participants; the participants just join the channel and start speaking with each other.
To create a channel, select Options > New channel > Create new.
Select Options and define the following:
•
•
•
•
Channel name — Write the channel name.
Channel privacy — Select Private or Public.
Nickname in channel — Enter your nickname (20 characters maximum) that is displayed to other users.
Channel thumbnail — Insert a picture that describes the channel.
To delete a channel, press the backspace key.
When you log in to push to talk, push to talk automatically connects to the channels that were active when the application was
last closed.
Register PTT channels
To register a channel to the push to talk service, select Options > Register.
To edit the channel details, select Options > Edit.
Participant details
To view the currently active participants of a channel, select Options > Active members.
To view more information about a selected participant, select Options > Contact details.
To call a selected contact, select Options > Talk 1 to 1. To make a group call, select Options > Make PTT group call.
To send the contact a request to call you, select Options > Send callback request.
To add a contact to Contacts, select Options > Add to Contacts.
© 2007 Nokia. All rights reserved.
38
T e l e p h o n e
Join a channel
To join a channel, select Options > PTT channels. Select the channel you want to talk to, and press the voice key. Remember to
hold the device in front of you during a push to talk call so you can see the display. The display informs you when it is your turn
to speak. Speak towards the microphone, and do not cover the loudspeaker with your hands. Press and hold the voice key the
entire time you are talking. When you have finished talking, release the key.
To switch between channels during multiple calls, select Swap. The active channel is highlighted.
To view the currently active participants in the channel, select Options > Active members.
To invite a participant to a channel, select Options > Send invitation.
Push to talk log
To open the push to talk log, select Options > PTT log. The log shows the date, time, duration, and other details of your push
to talk calls.
Tip: To initiate a one-to-one call from PTT log, select the desired log event and press the voice key.
Exit push to talk
Select Options > Exit. Select Yes to log out and close the service. Press No if you want to keep the application active on the
background.
Net calls
With the net call service (network service), you can make and receive calls over the internet.
Your device supports voice calls over the internet (net calls). Your device attempts emergency calls primarily over cellular
networks. If an emergency call using cellular networks is not successful, your device attempts an emergency call through your
net call provider. Due to the established nature of cellular telephony, you should use cellular networks for emergency calls, if
possible. If you have cellular network coverage available, make sure that your cellular phone is switched on and ready to make
calls before you attempt an emergency call. The capability for an emergency call using internet telephony depends on the
availability of a WLAN network and your net call provider's implementation of emergency call capabilities. Contact your net call
provider to check the internet telephony emergency call capability.
VoIP (voice over internet protocol) technology is a set of protocols that facilitate phone calls over an IP network, such as the
internet. VoIP phone calls can be established between computers, between mobile phones, and between a VoIP device and a
traditional telephone. To make or receive a VoIP call, your device must be within WLAN coverage, for example.
The availability of the net call service may vary according to your country or sales area.
Define the net call settings
Before you can make net calls, you need to define the net call settings. After you have defined the net call settings with these
instructions, your device logs in to the net call service automatically when you select Menu > Connect. > Internet tel..
First: define a SIP profile
1. Select Menu > Tools > Settings > Connection > SIP settings > Options > Add new, and enter the required information.
See "Edit SIP profiles," p. 82. You must define all available SIP settings, but ensure that Registration is set to Always on.
Contact your net call provider for the correct information.
2. Select Proxy server, and set Transport type to Auto.
3. Select Back until you return to the Connection menu.
Second: define a net call profile
1. Select Internet tel. settings > Options > New profile. Enter a name for the profile, and select the SIP profile you just created.
2. Select Back until you return to the main menu.
Third: select a preferred net call profile (optional)
If you select a preferred net call profile, Internet tel. automatically uses this network profile to connect to the net call service.
1. Select Menu > Connect. > Internet tel..
2. Select Preferred profile and the net call profile you just created.
3. Select Back until you return to the main menu.
Tip: You can also use manual login to the net call service. Use the same settings instructions as with automatic login,
but ensure that Registration is set to When needed and Transport type is set to UDP or TCP. With manual login, you
need to manually select the network used in the net call service.
© 2007 Nokia. All rights reserved.
39
T e l e p h o n e
Connect to the net call service
To make or receive a net call, your device must be connected to a net call service. Select Menu > Connect. > Internet tel..
If you have selected automatic login, your device automatically connects to the net call service. If you manually login to the
service, choose an available connection network from the list, and select Select to connect to the net call service. The saved
networks, which are marked with a star icon, are shown first on the list. If you want to stop the connection from establishing,
select Cancel.
Select Options and from the following:
•
Connect to service — to establish a connection to a service when there is a net call service and suitable connection network
available.
•
•
Disconnect from serv. — to end the connection to the net call service.
Change service — to choose the net call service for outgoing calls if the device is connected to more than one service. This
option is shown only if there is more than one configured service available.
•
•
Configure service — to configure new services. This option is shown only if there are services that have not been configured.
Save network — to save the network to which you are currently connected. The previously saved networks are marked with
a star icon on the list of connection networks. This option is shown only if you are connected to an unsaved wireless LAN
network.
•
•
Use hidden network — to connect to a net call service using a hidden wireless LAN network.
Refresh — to manually refresh the list of connection networks. Use this option, if your wireless LAN network is not shown on
the list. The list is also refreshed automatically every 15 seconds.
The available options may vary.
Your device can be connected only to one wireless LAN access point at a time. If you use two or more net call services, which
use the same access point, your device may be connected to multiple services at the same time. The service used for outgoing
net calls is shown in the view, where the connection networks are listed, and can be changed by selecting Change service.
After you have successfully connected to a service, you can save the used wireless LAN network as a known access point.
Connect using a shortcut
You may have a shortcut for Internet tel. in the active standby or you can add a shortcut if it is not available. See "Standby mode
settings," p. 80. By using the shortcut, you can register manually if a net call service and an access point are available. If you
are already connected to a net call service, the device asks if you want to disconnect from the service.
Make net calls
If you set Internet call as the preferred call type and your device is connected to a net call service, calls are made as net calls as
the default.
To set the preferred call type for outgoing calls, select Menu > Connect. > Internet tel. > Options > Settings > Preferred call
type > Cellular or Internet call.
You can make a net call from all applications where you can make a regular voice call.
To make a net call in the standby mode, enter the phone number or internet address, and press the call key.
To make a net call to an address that does not start with a digit, press any number key when the device is in the standby mode;
then press the blue function key to clear the display and to switch the device from number mode to letter mode. Write the
address, and press the call key.
You can also make a net call from Contacts and Log. To make a call from Contacts, select Menu > Contacts, and scroll to the
desired contact. Select Options > Call > Internet call.
To make a call from Log, select Menu > Log > Recent calls and Missed calls, Recvd. calls or Dialled nos., and scroll to the desired
contact. Select Options > Call > Internet call.
Service settings
Select Menu > Connect. > Internet tel. > Options > Settings > Settings:.
Select Login type to view or change the way Internet tel. connects to the net call service. Select from the following:
•
Automatic — Login automatically to the net call service. When a known network is found, the device automatically connects
to the net call service. If you use the automatic login type for wireless LAN networks, the device periodically scans for wireless
LAN networks, which increases the demand on battery power and reduces the battery life.
Manual — Login manually to the net call service.
•
Select Saved conn. networks to view the connection networks you have saved for the net call service or the connection networks,
which are recognized by the net call service. These networks are used for automatic login and are marked with a star icon on
the list of connection networks. To remove a connection network from the service, select Options > Remove.
Select Edit service settings to open the service-specific settings. This option is only available if a service-specific software plug-
in has been installed in the device.
© 2007 Nokia. All rights reserved.
40
T e l e p h o n e
Voice commands
Select Menu > Tools > Voice cm..
Use voice commands to make phone calls and to launch applications, profiles, or other functions on the device.
The device creates a voice tag for the entries in the contacts list and for the functions designated in the Voice cm. application.
When a voice command is spoken, the device compares the spoken words to the voice tag in the device.
Voice commands are not dependent on a speaker’s voice; however, the voice recognition in the device adapts to the main user’s
voice to better recognize voice commands.
Make a call
The voice tag for a contact is the name or nickname that is saved on the contact card in Contacts. To listen to the voice tag, open
a contact card, and select Options > Play voice tag.
1. To make a call using a voice command, press and hold the voice key.
2. When you hear the tone or see the visual display, clearly speak the name saved on the contact card.
3. The device plays a synthesized voice tag for the recognized contact in the selected device language, and displays the name
and number. After a timeout, the device dials the number. If the recognized contact was not correct, select Next to view a
list of other matches or Quit to cancel dialing.
If several numbers are saved under the contact, the device selects the default number, if it has been set. Otherwise, the device
selects the first available number of the following fields: Mobile, Mobile (home), Mobile (business), Telephone, Tel. (home), and
Tel. (business).
Launch an application
The device creates voice tags for the applications listed in the Voice cm. application.
To launch an application using a voice command, press and hold the voice key, and clearly speak the voice command. If the
recognized application was not correct, select Next to view a list of other matches or Quit to cancel.
To add more applications to the list, select Options > New application.
To change the voice command of an application, scroll to the application, and select Options > Change command. Type the
new voice command, and select OK.
Change profiles
The device creates a voice tag for each profile. To set on a profile using a voice command, press and hold the voice key, and say
the name of the profile.
To change the voice command, scroll to the desired profile, and select Profiles > Options > Change command.
Voice command settings
To switch off the synthesizer that plays recognized voice commands in the selected device language, select Options >
Settings > Synthesiser > Off.
To reset voice recognition learning when the main user of the device has changed, select Reset voice adapts..
Voice mailbox
Select Menu > Tools > Voice mail.
When you open the voice mailbox application for the first time, you are asked to enter the number of your voice mailbox. To
change the number, select Options > Change number. To call the number, select Options > Call voice mailbox.
Tip: To call your voice mailbox (network service) in standby mode, press and hold 1, or press 1 then the call key.
Log
Select Menu > Log.
In the Log, you can view information about the communication history of the device.
To receive correct log information, the device must be switched on, the device must have a valid SIM card installed, and you
must be located in a service area of the cellular network. The GPRS connection is put on hold during voice calls unless the network
supports dual transfer mode or you have a USIM card and are within the coverage of a UMTS network.
Note: The actual invoice for calls and services from your service provider may vary, depending on network features,
rounding off for billing, taxes, and so forth.
© 2007 Nokia. All rights reserved.
41
T e l e p h o n e
To view the logs for recent voice calls, their approximate duration, and packed data connections, select Recent calls, Call
duration, or Packet data; and press the scroll key.
To sort the events by type or direction, scroll right to open the general log, and select Options > Filter. Scroll to a filter type,
and press the scroll key. Select the type or direction, and press the scroll key.
To set the time how long all communication events are held in the log, select Options > Settings > Log duration, an option,
and OK.
To clear missed and received calls and dialed numbers, select Recent calls > Options > Clear recent calls.
To reply to a caller with a message, select Recent calls > Missed calls > Options > Create message. You can send text messages
and multimedia messages.
To add the caller or the sender of a message to Contacts, select the caller or sender of a message, and select Options > Add to
Contacts.
To view the amount of data sent or received using GPRS, select Packet data.
To clear the GPRS counters, select Options > Clear counters. Enter your lock code, and select OK.
Log settings
To set the time for keeping all communication events in the Log, select Options > Settings > Log duration, an option from the
list, and OK.
To see the call duration during the call, select Options > Settings > Show call duration > Yes.
© 2007 Nokia. All rights reserved.
42
6.
Contacts
Press the contacts key.
Manage all of your contact information, such as phone numbers and addresses. Add a personal ringing tone, voice tag, or a
thumbnail image to a contact. Send contact information to compatible devices or receive contact information as business cards
from compatible devices, and add them to your own list of contacts.
To add a contact, select Options > New contact. Enter the contact information, and select Done.
To edit information in a contact card, scroll to the contact, and select Options > Edit > Options. Select from the following:
•
Add thumbnail — Add a thumbnail image that will display when a contact calls you. The image must be previously saved to
your device or memory card.
•
•
•
•
Remove thumbnail — Remove the image from the contact card.
Add detail — Add fields of information to a contact card, such as Job title.
Delete detail — Delete any details that you added to a contact card.
Edit label — Edit the field names of the contact card.
Manage contact groups
Create a contact group so that you can send text or e-mail messages to several recipients at the same time.
1. Scroll to the right, and select Options > New group.
2. Enter a name for the group or use the default name, and select OK.
3. Open the group, and select Options > Add members.
4. Scroll to each contact you want to add to the group, and press the scroll key to mark it.
5. Select OK to add all marked contacts to the group.
The following options are available when you select Options in the contact groups view:
•
•
•
•
•
•
•
•
•
PTT options — Make a push to talk call either to an individual or to a group, or send a callback request.
Open — Open the contact group and view the group members.
Create message — Send a message.
New group — Create a new contact group.
Delete — Delete a contact group.
Rename — Rename the contact group.
Ringing tone — Assign a ringing tone to a contact group.
Contacts info — View the information for a contact group.
Settings — Set the name display settings for contact group members.
To remove a contact from a contact group, open the contact group. Scroll to the contact you want to remove, and select
Options > Remove from group > Yes.
Tip: To check the group in which a contact belongs, press the contacts key. Scroll to the contact, and select Options >
Belongs to groups.
To view or edit a contact within a contact group, open the contact group. Scroll to the contact you want to view or edit, and
select Options. Select from the following options: Open Opens the contact and displays contact information. Call Select Voice
call or Video call, and call the contact. Create message Create and send a text message or multimedia message to the contact.
Remove from group Remove the contact from the contact group. Belongs to groups View all contact groups that a contact
belongs to.
Manage default information
Assign a default number or address to a contact so you can easily call or send a message to the default number or address, even
if several numbers or addresses are saved to that contact.
To change default information for a contact, open the contact, and select Options > Defaults. Select the number or address you
want to set as a default, and select Assign.
The default number or address is underlined in the contact.
Copy contacts between SIM and device memory
To copy contacts from a SIM card to device memory, select Options > SIM contacts > SIM directory to open the SIM directory.
Mark the contacts you want to copy, or select Mark all to copy all contacts. Select Options > Copy to Contacts.
To copy contacts from the device memory to a SIM card, select Options > Copy to SIM direct.. Mark the contacts you want to
copy, or select Mark all to copy all contacts. Select Options > Copy to SIM direct..
© 2007 Nokia. All rights reserved.
43
C o n t a c t s
Select Options > SIM contacts > SIM directory to see the names and numbers stored on the SIM card. In SIM directory you can
add, edit, or copy numbers to Contacts, and you can make calls.
Select ringing tones for contacts
Select a ringing tone for a contact or contact group. If the caller's phone number is sent with the call and your device recognizes
the number, the ringing tone plays when the contact calls you.
To select a ringing tone for a contact or contact group, open the contact or contact group, and select Options > Ringing tone.
A list of ringing tones opens. Select the ringing tone you want to use.
To remove the ringing tone, select Default tone from the list of ringing tones.
Business cards
Press the contacts key.
You can send, receive, view, and save contact cards as business cards in vCard or Nokia Compact Business Card format.
You can send business cards to compatible devices using SMS, MMS, or e-mail, or an infrared or Bluetooth connection.
To send a business card, select the contact card from the contacts list, and select Options > Send. Select Via text message, Via
multimedia, Via e-mail, Via Bluetooth, or Via infrared. Enter the phone number or address, or add a recipient from the contacts
list. Select Options > Send. If you select SMS as the sending method, contact cards are sent without images.
To view a received business card, select Show from the displayed notification, or open the message from the inbox folder in
Messag..
To save a business card, select Options > Save business card when the incoming message appears on the device.
To save a received business card, select Options > Save business card.
To delete a received business card, select Options > Delete.
© 2007 Nokia. All rights reserved.
44
7.
Nokia Team suite
Select Menu > Office > Team suite.
With Nokia Team Suite, you can create, edit, and delete teams, and send messages, view teams' web pages and communication
history, and make phone calls to teams at one go.
To create a new team, select Options > Team > Create. Give a name for the team and enter the conference call service
information, if needed. Then select the members for the team.
To select an action, select the team to which you want to apply the action, scroll right to the action bar, and select the desired
action. If you do not want to apply the action to all team members, open the team, and select the desired members by pressing
the scroll key. Then select the action.
To find more actions than shown on the action bar, select Options > Actions. The following actions are available:
•
Call — Make a phone call to the team or selected team members. The team members are called one by one and put on hold
until the calls can be merged into a conference call (network service). The maximum number of participants depends on the
network service.
•
•
•
•
•
•
Create message — Send a text message, a multimedia message, or an e-mail to the team or selected team members.
Call conference service — Start a call to the conference call service (network service) defined for the selected team.
Communication log — View the communication log for the team or selected team members.
In-device search — Search for content related to the team or team members.
Push to talk — Communicate via push to talk (network service) with the team or selected team members.
Team Web pages — Open the bookmark folder that contains the team's web pages.
To select which actions are shown in the action bar and in which order, select Options > Settings > Action bar items.
Edit teams
To add team members, select Options > Members > Add.
To remove team members, select Options > Members > Remove.
To edit the details of a member, select Options > Members > Edit.
To select whether to see the team members' pictures on the display, select Options > Settings > View contact image.
To see to which teams a member belongs, select Options > Members > Belongs to teams.
© 2007 Nokia. All rights reserved.
45
8.
Calendar
Select Menu > Calendar.
In Calendar, you can create and view scheduled events and appointments. You can also set alarms for calendar entries.
You can synchronize your calendar data with a compatible computer using Nokia PC Suite. For information on synchronization,
see the PC Suite guide.
Create calendar entries
You can create four types of calendar entries:
•
•
•
Meeting entries have a specific date and time.
Memo entries are related to the whole day but not to a specific time of the day.
Anniversary entries remind you of birthdays and special dates. They refer to a certain day but not a specific time of the day.
Anniversary entries are repeated every year.
•
To-do entries remind you of a task that has a due date but not a specific time of the day.
To create a calendar entry, scroll to a date, and select Options > New entry. Select an entry type. Available settings for meeting,
memo, anniversary, and to-do entries vary.
Select from the following:
•
•
•
•
•
•
•
•
Subject or Occasion — Enter a description for the entry.
Location — Enter any necessary location information.
Start time — Enter the start time.
End time — Enter the end time.
Start date or Date — Enter the start date or date the event occurs.
End date — Enter the end date.
Alarm — Set an alarm for meeting and anniversary entries. The alarm is displayed in the Day view.
Repeat — Specify whether you want the entry to be repeated and when. Define the repeat type, frequency, and possible
ending date.
•
Synchronisation — If you select Private, the calendar entry can be seen only by you and is not shown to others with online
access to view the calendar. If you select Public, the calendar entry is shown to others who have access to view your calendar
online. If you select None, the calendar entry is not copied to your PC when you synchronize.
Tip: Make sure you have selected the correct city in the Clock application, because scheduled calendar entries may
change when the current city is changed and is on another time zone.
To open and edit an existing entry, scroll to the entry, and select Options > Open. Edit the details in the various fields.
Tip: When you edit or delete a repeated entry, choose how you want the change to take effect. If you select All calendar
entries deleted, all repeated entries are deleted. If you select Delete entry, only the current entry is deleted.
To-do
You can create and maintain a task or list of tasks that must be done by a certain day. Each task can be assigned a due date, and
an alarm.
To open the list of to-do notes, select Options > To-do view.
To add a to-do note, select Options > New entry > To-do. Start to write the task in the Subject field. You can set a due date for
the task, create an alarm for it, and specify a priority. The priority icons are ( ! ) High and ( - ) Low. There is no icon for Normal.
To mark a task as completed, scroll to the task in the to-do list, and select Options > Mark as done.
To restore a task, scroll to it in the todo list, and select Options > Mark as not done.
Calendar settings
Select Options > Settings to modify the Calendar alarm tone, Default view, Week starts on, and Week view title.
Calendar views
To switch between the different calendar views, select Options in any calendar view. Select a type of view from the list.
Tip: When viewing Calendar in any view, press the blue function key and * to quickly switch to another view.
To set the default calendar view, select Options > Settings > Default view > Month view , Week view, Day view, or To-do
view.
© 2007 Nokia. All rights reserved.
46
C a l e n d a r
To view a specific date in the calendar view, select Options > Go to date. Enter the date, and select OK.
In the Month view, you can view the entire month at one time. Each row shows one week of dates. The active month is displayed,
and the active day is either today or the last day that was viewed. The active day is marked with a colored square. Days that
have scheduled events are marked with a small triangle in the bottom right corner. Scroll to switch between the days of the
month and day entries.
Tip: When viewing Calendar in any view, press the blue function key and * to quickly switch to another view.
The Week view shows the events for the selected week in seven day boxes. Today's date is marked with a colored square. Memos
and anniversaries are placed before 8:00 a.m.
To change the starting day of the week, select Options > Settings > Week starts on.
The Day view view shows the events for the selected day. Entries are grouped into time slots according to their starting time.
To view the previous or next day, scroll left or right.
The To-do view view shows the to-do items for the selected day.
Send calendar entries
To send a calendar entry to a compatible device, scroll to the entry, and select Options > Send > Via text message, Via
multimedia, Via e-mail, Via Bluetooth, or Via infrared.
Add a received calendar entry to your calendar
You can receive a calendar entry as an attachment to a multimedia or e-mail message.
To add a received calendar entry to your calendar, open the calendar entry attachment in the message, and select Options >
Save to Calendar. The entry is added to your default calendar.
© 2007 Nokia. All rights reserved.
47
9.
Clock
Select Menu > Office > Clock.
Tip: To update date and time automatically (network service), select Options > Settings > Network operator time >
Auto-update.
To change the clock type, select Options > Settings > Clock type > Analogue or Digital.
Date and time settings
To change the date and time, their display formats, alarm tone, and to define whether you want to use automatic time update,
select Options > Settings and from the following:
•
•
•
•
•
•
•
•
•
•
Time — Enter the time, and select OK.
Time zone — Enter the time zone, and select OK.
Date — Enter the date, and select OK.
Date format — Change how the date is displayed. Scroll to the desired format, and select OK.
Date separator — Change the symbol that separates days, months, and years. Scroll to the symbol you want, and select OK.
Time format — Select 24-hour or 12-hour.
Time separator — Select the symbol that separates hours and minutes.
Clock type — Select Analogue or Digital.
Clock alarm tone — Select the tone that you want to use for the alarm clock.
Network operator time — Update time, date, and time zone information automatically (network service). Select Auto-
update to activate. This service may not be available in all networks.
Alarm clock
If the alarm time is reached while the device is switched off, the device switches itself on and starts sounding the alarm tone.
If you select Stop, the device asks whether you want to activate the device for calls. Select No to switch off the device or Yes to
make and receive calls. Do not select Yes when wireless phone use may cause interference or danger.
To set an alarm, select Options > Set alarm. Enter the alarm time, and select OK.
To view and change alarms, select Options > Reset alarm.
To remove an alarm, select Options > Remove alarm.
Add and delete cities
To add a city, scroll right, and select Options > Add city. Scroll to a city, and select Options > Select.
Tip: To search for a city in the Cities list, select Options > Add city > Options > Find. Enter the city name in the search
field.
To delete a city, scroll right, scroll to the city, and select Options > Remove.
Changing the city in which you are located may change the general system time of your device.
© 2007 Nokia. All rights reserved.
48
10.
Connectivity
Your service provider may have requested that certain features be disabled or not activated in your device. If so, they will not
appear on your device menu. Your device may also have been specially configured. This configuration may include changes in
menu names, menu order, and icons. Contact your service provider for more information.
Your device offers several options (network services) to connect to the Internet, a corporate intranet, or to another device or
PC. Wireless methods include wireless LAN, Bluetooth, and infrared. Your device supports a wired solution with a USB (Universal
Serial Bus) cable connection for Nokia PC Suite. Your device also allows you to communicate using net calls (Voice over IP), push
to talk, instant messaging (chat), and modem-based connections.
Packet data (GPRS)
GPRS (general packet radio service) enables wireless access for mobile phones to data networks (network service). GPRS uses
packet data technology where information is sent in short bursts of data over the mobile network. The benefit of sending data
in packets is that the network is occupied only when sending or receiving data. As GPRS uses the network efficiently, it allows
for quick data connection set-up and fast data transmission speeds.
You must subscribe to the GPRS service. For availability and subscription to GPRS, contact your network operator or service
provider.
Enhanced GPRS (EGPRS) is similar to GPRS, but it enables faster connection. For more information on the availability of EGPRS
and data transfer speed, contact your network operator or service provider. Note that when you have selected GPRS as a data
bearer, the device uses EGPRS instead of GPRS if this is available in the network.
During a voice call, you cannot establish a GPRS connection, and any existing GPRS connection is put on hold unless the network
supports dual transfer mode.
UMTS
UMTS (Universal Mobile Telecommunications System) is a 3G mobile communication system. Besides voice and data, UMTS
enables audio and video delivery to wireless devices.
Your device can automatically switch between the GSM and UMTS networks.
To select which network to use, select Menu > Tools > Settings > Network and the network in Network mode. If you want
the device to switch between the networks automatically, select Dual mode.
The GSM network is indicated with , the UMTS network with
.
When you use your device in GSM and UMTS networks, multiple data connections can be active at the same time, and access
points can share a data connection. In the UMTS network, data connections remain active during voice calls. You can, for example,
browse the Web faster than previously possible while simultaneously speaking on the phone.
Cable connection
Install Nokia PC Suite to your computer before you use a cable connection, as Nokia PC Suite automatically installs the USB data
cable driver to your computer. You can use the Data transfer mode without installing Nokia PC Suite.
Select Menu > Connect. > Data cbl..
Using a USB data cable, you can connect your device to a compatible PC . Connect the USB data cable to the bottom of the device.
When the USB cable is connected, the device asks which connection mode to use. If you have already installed Nokia PC Suite,
select PC Suite to use your device as a modem.
To change the device type you normally connect to your device with the data cable, press the scroll key.
Select from the following:
•
Ask on connection — Select whether you want to be asked for the device type every time you connect the data cable to your
device.
•
•
PC Suite — Connect the PC Suite to your device with the data cable, and use your device as a modem.
Data transfer — Access and transfer data such as music or image files from your computer using the data cable connection.
To use the Data transfer mode, make sure that you have not selected USB as a connection type in the Manage connections
settings in Nokia PC Suite. Insert a memory card to your device, connect the device to a compatible computer with the USB
data cable, and select Data transfer when the device asks which mode is used. In this mode, your device acts as a mass storage
device and you can see it as a removable hard drive in your computer. The device will switch into the Offline profile if this is
selected. End the connection from the PC (for example, from an Unplug or Eject Hardware wizard in Windows) to avoid
damaging the memory card. After you end the connection, the device returns to the profile in which it was before using the
data transfer mode.
© 2007 Nokia. All rights reserved.
49
C o n n e c t i v i t y
Bluetooth
This device is compliant with Bluetooth Specification 1.2 supporting the following profiles: Generic Access Profile, Serial Port
Profile, Dial-up Networking Profile, Headset Profile, Handsfree Profile, Generic Object Exchange Profile, Object Push Profile, File
Transfer Profile, SIM Access Profile, and Basic Imaging Profile. To ensure interoperability between other devices supporting
Bluetooth technology, use Nokia approved enhancements for this model. Check with the manufacturers of other devices to
determine their compatibility with this device.
Bluetooth technology enables wireless connections between electronic devices within a range of 10 meters (33 feet). A Bluetooth
connection can be used to send images, videos, texts, business cards, calendar notes, or to connect wirelessly to devices using
Bluetooth technology, such as computers.
Since devices using Bluetooth technology communicate using radio waves, your device and the other devices do not need to
be in direct line-of-sight. The two devices only need to be within a maximum of 10 meters of each other, although the connection
can be subject to interference from obstructions such as walls or from other electronic devices.
Start using Bluetooth connectivity
There may be restrictions on using Bluetooth technology in some locations. Check with your local authorities or service provider.
Features using Bluetooth technology, or allowing such features to run in the background while using other features, increase
the demand on battery power and reduce the battery life.
Select Menu > Connect. > Bluetooth.
To activate Bluetooth, press the blue function key and the Ctrl key simultaneously. To deactivate, press the blue function key
and the Ctrl key again. If you use this shortcut to activate Bluetooth, you will not be asked to name your device.
1. When you activate Bluetooth for the first time, you are asked to give a name to your device. Give your device a unique name
to make it easy to recognize if there are several Bluetooth devices in the vicinity.
2. Select Bluetooth > On.
3. Select My phone's visibility > Shown to all.
Your device and the name you entered can now be seen by other users with devices using Bluetooth technology.
Settings
Define the following settings:
•
•
Bluetooth — Select On to be able to connect to another compatible device using Bluetooth connectivity.
My phone's visibility — Select Shown to all to allow other devices using Bluetooth technology to find your device when you
have set Bluetooth > On. To prevent other devices from finding your device, select Hidden. Even if you select Hidden, paired
devices can still detect your device.
•
•
My phone's name — Enter a name for your device. The name is visible to other devices that search for devices using Bluetooth
technology. The maximum length of the name is 30 characters.
Remote SIM mode — Select On to enable another device, such as a compatible car kit enhancement, to use the SIM card in
your device to connect to the network. See "SIM access profile," p. 52.
If Bluetooth was turned off as a result of entering the Offline profile, you must re-enable Bluetooth manually.
Security tips
When you are not using Bluetooth connectivity, select Bluetooth > Off or My phone's visibility > Hidden.
Do not pair with an unknown device.
Send data
Several Bluetooth connections can be active at a time. For example, if you are connected to a headset, you can also transfer files
to another compatible device at the same time.
1. Open the application where the item you want to send is stored.
2. Select the item, and select Options > Send > Via Bluetooth. The device searches for other devices using Bluetooth technology
within range and lists them.
Tip: If you have sent data using Bluetooth before, a list of the previous search results is displayed. To search for
more Bluetooth devices, select More devices.
3. Select the device with which you want to connect, and press the scroll key to set up the connection. If the other device
requires pairing before data can be transmitted, you are asked to enter a passcode.
4. When the connection has been established, Sending data is shown.
The Sent folder in Messag. does not store messages sent using Bluetooth connectivity.
© 2007 Nokia. All rights reserved.
50
C o n n e c t i v i t y
If you have sent items using Bluetooth before, a list of the previous search results is displayed. To search for more Bluetooth
devices, select More devices.
To use a Bluetooth audio enhancement such as Bluetooth handsfree or headset you need to pair your device with the
enhancement. See the enhancement user guide for the passcode and further instructions. To connect to the audio enhancement,
press the power key to turn on the enhancement. Some audio enhancements connect automatically to your device. Otherwise
open Paired devices, scroll to the enhancement, and select Options > Connect.
Bluetooth connectivity indicators
Bluetooth is on.
When the icon is blinking, your device is trying to connect to the other device. When the icon is shown continuously, the
Bluetooth connection is active.
Pair devices
Select Menu > Connect. > Bluetooth, and scroll right to open the Paired devices page.
Before pairing, create your own passcode (1-16 digits), and agree with the user of the other device to use the same code. Devices
that do not have a user interface have a fixed passcode. You need the passcode only when you connect the devices for the first
time. After pairing, it is possible to authorize the connection. See "Authorize a device," p. 51. Pairing and authorizing the
connection makes connecting quicker and easier, as you do not have to accept a connection between paired devices every time
you establish the connection.
The passcode for remote SIM access must have 16 digits.
1. Select Options > New paired device. The device starts to search for Bluetooth devices within range.
Tip: If you have sent data using Bluetooth before, a list of the previous search results is displayed. To search for
more Bluetooth devices, select More devices.
2. Select the device with which you want to pair, and enter the passcode. The same passcode must be entered to the other
device as well.
3. Select Yes to make the connection between your device and the other device automatic or No to confirm the connection
manually every time a connection attempt is made. After pairing, the device is saved to the paired devices page.
To give a nickname to a paired device that is only displayed in your device, scroll to the device with which you have paired, and
select Options > Assign short name.
To delete a pairing, select the device whose pairing you want to delete and Options > Delete. To delete all pairings, select
Options > Delete all.
Tip: If you are currently connected to a device and cancel the pairing with that device, pairing is removed immediately,
and the connection is switched off.
Note that when you use Nokia PC Suite, you need to pair the devices from the PC Suite. For information on PC Suite pairing, see
the PC Suite guide.
Authorize a device
If you trust a paired device, you can allow it to connect automatically to your device. You can select from the following options:
•
Setasauthorised—Connectionsbetweenyourdeviceandtheotherdevicecanbemadewithoutyourknowledge. Noseparate
acceptance or authorization is needed. Use this status for your own devices, such as your compatible headset or PC, or devices
that belong to someone you trust.
•
Set as unauthorised — Connection requests from the other device must be accepted separately every time.
Receive data
If you want to receive data using Bluetooth, select Bluetooth > On and My phone's visibility > Shown to all. When you receive
data through Bluetooth connectivity, a tone sounds, and you are asked if you want to accept the message. If you accept, the
message is placed in the Inbox folder in Messag.
Tip: You can access the files in the device or on the memory card using a compatible accessory that supports the File
Transfer Profile Client service (for example, a laptop computer).
End a Bluetooth connection
A Bluetooth connection is disconnected automatically after sending or receiving data. Only Nokia PC Suite and some
enhancements such as headsets may maintain a connection even if not actively used.
© 2007 Nokia. All rights reserved.
51
C o n n e c t i v i t y
SIM access profile
When the wireless device is in the remote SIM mode, you can only use a compatible connected enhancement, such as a car kit,
to make or receive calls. Your wireless device will not make any calls, except to the emergency numbers programmed into your
device, while in this mode. To make calls from your device, you must first leave the remote SIM mode. If the device has been
locked, enter the lock code to unlock it first.
With the SIM access profile, you can access the SIM card of your device from a compatible car kit device. This way, you do not
need a separate SIM card to access SIM card data and connect to the GSM network.
To use the SIM access profile, you need the following:
•
•
Compatible car kit device that supports Bluetooth wireless technology
Valid SIM card in your device
For more information about car kit devices and compatibility with your device, see www.nokia.com and your car kit user guide.
Manage the SIM access profile
1. Select Menu > Connect. > Bluetooth to activate Bluetooth connectivity in your device.
2. To enable remote SIM access, scroll to Remote SIM mode, and press the scroll key.
3. Activate Bluetooth in the car kit device.
4. Use your car kit device to start a search for compatible devices. For instructions, see the user guide of your car kit device.
5. Select your device from the list of compatible devices.
6. To pair the devices, enter the Bluetooth passcode shown on the display of the car kit device to your device.
7. Authorize the car kit device. Select Menu > Connect. > Bluetooth, and scroll to the Paired devices page. Scroll to the car kit
device, and enter the Bluetooth passcode. When the device asks to make the connection automatic, select Yes. Connections
between your device and the car kit device can be made without separate acceptance or authorization. If you select No,
connection requests from this device must be accepted separately every time.
Tip: If you have already accessed the SIM card from the car kit with the active user profile, the car kit searches
automatically for a device with the SIM card. If it finds your device, and automatic authorization is activated, the car
device automatically connects to the GSM network when you switch on the car ignition.
When you activate the remote SIM access profile, you can use applications on your device that do not need network or SIM
services.
To end the remote SIM access connection from your device, select Menu > Connect. > Bluetooth > Remote SIM mode > Off.
Infrared
Do not point the infrared (IR) beam at anyone's eye or allow it to interfere with other IR devices. This device is a Class 1 laser
product.
Use infrared to connect two devices and transfer data between them. With infrared, you can transfer data such as business
cards, calendar notes, and media files with a compatible device.
Send and receive data
1. Ensure that the infrared ports of the devices face each other. The positioning of the devices is more important than angle or
distance.
2. Select Menu > Connect. > Infrared, and press the scroll key to turn on infrared on your device. Turn on infrared on the other
device.
Tip: You can also turn on infrared by pressing the blue function key and the Chr key simultaneously.
3. Wait a few seconds until an infrared connection is established.
4. To send, locate the desired file in an application or the file manager, and select Options > Send > Via infrared.
If data transfer is not started within 1 minute after the activation of the infrared port, the connection is cancelled and must be
started again.
All items received through infrared are placed in the Inbox folder in Messag..
Positioning devices away from each other breaks a connection, but the infrared light beam remains active on your device until
it is deactivated.
Modem
Select Menu > Connect. > Modem.
Together with a compatible computer, you can use your device as a modem to connect to the Web.
Before you can use your device as a modem
© 2007 Nokia. All rights reserved.
52
C o n n e c t i v i t y
•
•
•
•
You must subscribe to the appropriate network services from your service provider or Internet service provider.
You need a compatible computer with infrared connectivity.
You must have Nokia PC Suite installed on your computer.
You must have the appropriate drivers installed on your computer. You may need to install or update infrared drivers. After
you have installed Nokia PC Suite, follow the instructions on the computer display to install the drivers and connect your
device to the computer.
After you have installed Nokia PC Suite and the appropriate drivers, start Nokia PC Suite on your computer. Select Connect to the
Internet, and follow the instructions on the computer display.
To connect the device to a compatible computer using infrared, press the scroll key. Make sure the infrared ports of the device
and computer are directly facing each other with no obstacles between them.
You may not be able to use some of the other communication features when the device is used as a modem.
Email data roaming
Select Menu > Tools > Settings > Connection > Access point groups.
Your device allows roaming between wireless access technologies, such as WLAN and GPRS, for e-mail. For example, you can
start an e-mail session at home and continue the session on your way to work. While your session continues uninterrupted,
your handheld device switches from WLAN to GPRS and back to WLAN when you arrive at your workplace.
Access point groups
To create an access point group, select Access point groups > Options > New group. In the Group name field, enter a name
for the group. Define in the Conn. switching field whether to show the connection switching process on the display of your
device. Choose and edit the access points that belong to this group in the Access points section.
To add an access point to the selected access point group, select Access points > Options > Add access point, and select the
access point to add.
To edit an access point in an access point group, select the access point and Options > Edit.
To remove an access point in an access point group, select the access point and Options > Remove.
To set the order in which access points are used for email data roaming, select an access point group and Change. Scroll to an
access point, and select Options > Raise priority or Lower priority.
To change the SMTP settings of an access point, select the access point group from the list, and press the scroll key. Scroll to
Access points and press the scroll key. Select the desired access point from the access point list, select Options > SMTP
settings, and select from the following:
•
•
•
•
•
•
Override SMTP serv. — Override the current SMTP server settings.
SMTP server — Edit the server name or the server IP address.
Secure connection — Select whether to use secure connection.
Use authentication — Select whether to use authentication.
User name — Edit your user name for the SMTP server.
Password — Edit your password for the SMTP server.
Configure access point groups for mail and synchronization
To set an access point group for mail, select Menu > Messaging > Mailbox > Options > E-mail settings > Connection
settings > Incoming e-mail > Access point in use > Select group, and select the desired access point group.
To set an access point group for synchronization, select Menu > Connect. > Sync > Profile > Options > Edit sync profile >
Connection settings > Access point > Select group, and select the desired access point group.
Internet access points
An access point is where your device connects to a network. To use e-mail and multimedia services or to connect to the Internet
and browse web pages, you must first define Internet access points for these services. You may need to set up several Internet
access points, depending on the sites you want to access. For example, browsing the Web may require one access point, and
accessing your company intranet may require another. To connect to the Internet over GPRS, your device may have predefined,
default Internet access point settings.
When you switch on your device for the first time, the access points may be configured automatically based on the service
provider information in your SIM card. You can also receive the access points settings in a message from your service provider.
This might reduce the number of settings you need to enter yourself.
The available options may vary. Some or all access points may be preset for your device by your service provider. You may not
be able to add, edit, or delete access points.
© 2007 Nokia. All rights reserved.
53
C o n n e c t i v i t y
Contact your service provider and e-mail service provider for more information on access points and their settings.
Set up an Internet access point for data calls
1. Select Menu > Tools > Settings > Connection > Access points.
2. Select Options > New access point. To use an existing access point as a basis for the new one, select Use existing settings.
To start with an empty access point, select Use default settings.
3. Define the following settings.
•
•
•
•
Connection name — Enter a descriptive name for the connection.
Data bearer — Select Data call or High speed data (GSM only).
Dial-up number — Enter the modem telephone number of the access point. Use + before international numbers.
User name — Enter your user name if required by the service provider. User names are often case-sensitive and provided
by your service provider.
•
•
•
Prompt password — Select Yes to enter your password each time you log into a server or No to save the password in your
device memory and automate the login.
Password — Enter your password if required by the service provider. The password is often case-sensitive provided by
the service provider.
Authentication — Select Secure to always send your password encrypted or Normal to send your password encrypted
when possible.
•
•
•
Homepage — Enter the Web address of the page you want to display as a home page when you use this access point.
Data call type — Select Analogue or ISDN.
Max. data speed — Select the limit to apply to the transfer speed. If you select Automatic, the data transfer rate is
determined by the network and may be affected by network traffic. Some service providers may charge more for higher
data rates.
4. After defining the basic settings, select Options > Advanced settings to define the advanced settings or Back to save the
settings and exit.
Advanced Internet access point settings for data calls
After setting up a basic Internet access point for Data call or High speed data (GSM only), select Options > Advanced settings,
and define the following advanced settings.
•
•
•
•
IPv4 settings — Enter the device IP and name server addresses for IPv4 Internet protocol.
IPv6 settings — Enter the device IP and name server addresses for IPv6 Internet protocol.
Proxy serv. address — Enter the proxy server address.
Proxy port number — Enter the proxy server port number. Proxy servers are intermediate servers between a browsing service
and its users, which are used by some service providers. These servers may provide additional security and speed up access
to the service.
•
•
•
•
•
Use callback — Select Yes if you have a service that dials back to your device when you establish an Internet connection.
Callback type — Select Use server no. or Use other no., according to instructions from your service provider.
Callback number — Enter your data call phone number of your device, which the callback server uses.
Use PPP compress. — Select Yes to speed up the data transfer, if it is supported by the remote PPP server.
Use login script — Select Yes, if your Internet service provider requires a login script, or if you want to automate your login.
A login script is a sequence of instructions that the system follows during the login process.
Login script — Enter the login script. This setting is available only if you have selected Use login script > Yes.
Modem initialisation — Enter a command string for the connection setup, if required by your service provider.
•
•
Set up an Internet access point for packet data (GPRS)
When you switch the device on, it may recognize the SIM card provider and configure the correct text message, multimedia
message, and GPRS settings and access points automatically.
1. Select Menu > Tools > Settings > Connection > Access points.
2. Select Options > New access point. To use an existing access point as a basis for the new one, select Use existing settings.
To start with an empty access point, select Use default settings.
3. Define the following settings.
•
•
•
Connection name — Enter a descriptive name for the connection.
Data bearer — Select Packet data.
Access point name — Enter the name for the access point. The name is usually provided by your service provider or network
operator.
•
User name — Enter your user name if required by the service provider. User names are often case-sensitive and provided
by your service provider.
© 2007 Nokia. All rights reserved.
54
C o n n e c t i v i t y
•
•
•
•
Prompt password — Select Yes to enter your password each time you log into a server or No to save the password in your
device memory and automate the login.
Password — Enter your password if required by the service provider. The password is often case-sensitive provided by
the service provider.
Authentication — Select Secure to always send your password encrypted or Normal to send your password encrypted
when possible.
Homepage — Enter the Web address of the page you want to display as a home page when you use this access point.
4. After defining the settings, select Options > Advanced settings to define the advanced settings or Back to save the settings
and exit.
Advanced Internet access point settings for packet data (GPRS)
After setting up a basic Internet access point for packet data (GPRS), selectOptions > Advanced settings, and define the following
advanced settings.
•
•
•
•
Network type — Select IPv4 or IPv6 as the Internet protocol type. The Internet protocol defines how data is transferred to
and from your device.
Phone IP address — Enter the IP address of your device. Select Automatic to have the network provide the device IP address.
This setting is shown only if you select Network type > IPv4.
DNS address — Enter the IP addresses of the Primary DNS address and Secondary DNS addr. if required by your service provider
or network operator. Otherwise, the name server addresses are provided automatically.
Proxy serv. address — Enter the address of the proxy server. Proxy servers are intermediate servers between a browsing
service and its users, which are used by some service providers. These servers may provide additional security and speed up
access to the service.
Set up an Internet access point for wireless LAN
You can use the WLAN wizard to create Internet access points for wireless LAN, or define the access point manually. See "Wireless
Connection manager
Select Menu > Connect. > Conn. mgr..
To view the status of data connections or end connections, select Act. data conn..
To search for wireless LANs available within range, select Availab. WLAN.
View and end active connections
Note: The actual invoice for calls and services from your service provider may vary, depending on network features,
rounding off for billing, taxes, and so forth.
In the active connections view, you can see the open data connections: data calls, packet data connections, and wireless LAN
connections.
To view detailed information about network connections, select the connection from the list and Options > Details. The type
of information shown depends on the connection type.
To end a network connection, select the connection from the list and Options > Disconnect.
To end all active network connections simultaneously, select Options > Disconnect all.
To view the details of a network, press the scroll key.
Search for wireless LAN
To search for wireless LANs available within range, select Menu > Connect. > Conn. mgr. > Availab. WLAN. A list of found
networks is displayed.
The available wireless LAN view shows a list of wireless LANs within range, their network mode (infrastructure or ad-hoc), signal
strength indicator and network encryption indicators, and if your device has an active connection with the network.
To view the details of a network, press the scroll key.
To create an Internet access point in a network, select Options > Define access point.
© 2007 Nokia. All rights reserved.
55
11.
Wireless local area network (WLAN)
Some places, like France, have restrictions on the use of wireless LAN. Check with your local authorities for more information.
This device can detect and connect to a wireless local area network (WLAN). To use wireless LAN, a network must be available
in the location and your device must be connected to it.
See wireless LAN availability
Your device can show you whether wireless LAN is available.
To have your device show wireless LAN availability, select Menu > Tools > Settings > Connection > Wireless LAN > Show
availability.
If wireless LAN is available,
is shown on the display.
Tip: You can also scan for networks in range.
Wireless LAN connections
Important: Always enable one of the available encryption methods to increase the security of your wireless LAN
connection. Using encryption reduces the risk of unauthorized access to your data.
To use wireless LAN, you must create an internet access point (IAP) in a wireless LAN. Use the access point for applications that
need to connect to the internet. A wireless LAN connection is established when you create a data connection using a wireless
LAN Internet access point. The active wireless LAN connection is ended when you end the data connection. You can also end the
connection manually. See "Connection manager," p. 55.
You can use wireless LAN during a voice call or when packet data is active. You can only be connected to one wireless LAN access
point device at a time, but several applications can use the same internet access point.
When the device is in the Offline profile, you can still use wireless LAN (if available). Remember to comply with any applicable
safety requirements when establishing and using a wireless LAN connection.
If you move the device to another location within the wireless LAN and out of range of a wireless LAN access point, the roaming
functionality can automatically connect your device to another access point that belongs to the same network. As long as you
remain within range of access points that belong to the same network, your device can stay connected to the network.
Tip: To check the unique media access control (MAC) address that identifies your device, for example to configure the
MAC address of your device to a WLAN router, enter *#62209526# on the device keypad. The MAC address is shown on
the device display.
Operating modes
Your device enables different types of communication in a wireless LAN. The two operating modes are infrastructure and ad
hoc.
•
•
The infrastructure operating mode allows two kinds of communication: wireless devices communicate with each other
through a wireless LAN access point or wireless devices communicate with a wired LAN device through a wireless LAN access
point. The advantage of the infrastructure operating mode is that you can have more control over network connections
because they pass through an access point. A wireless device can access the services that are available in a regular wired LAN:
company database, e-mail, the Internet, and other network resources, for example.
In the ad hoc operating mode you can send data to and receive it from other devices with compatible wireless LAN support ,
for example, to be printed. These functions may require an additional third party application to work. No wireless LAN access
point is required. Simply make the necessary configurations and start communicating. Ad hoc networking is easy to set up,
but communication is limited to devices that are within range and support compatible wireless LAN technology.
WLAN wizard
The WLAN wizard helps you to connect to a wireless LAN.
The WLAN wizard shows the status of your wireless LAN connections and network searches in the active standby mode. To view
the available options, scroll to the row showing the status, and press the scroll key. Depending on the status, you can start the
web browser using a wireless LAN connection, disconnect from a wireless LAN, search for wireless LANs, or set network scanning
on or off.
If wireless LAN scanning is off and you are not connected to any wireless LAN, WLAN scanning off is displayed in the active
standby mode. To set scanning on and search for available wireless LANs, scroll to the status, and press the scroll key.
To start a search for available wireless LANs, scroll to a status, press the scroll key, and select Search for WLAN. To set wireless
LAN scanning off, scroll to a status, press the scroll key, and select Switch WLAN scan off.
© 2007 Nokia. All rights reserved.
56
W i r e l e s s l o c a l a r e a n e t w o r k ( W L A N )
When Start Web browsing is selected, the WLAN wizard automatically creates an internet access point (IAP) for the selected
wireless LAN. The IAP can also be used with other applications requiring wireless LAN connection.
If you select a secured wireless LAN network, you are asked to enter the relevant passcodes. To connect to a hidden network,
you must enter the correct hidden service set identifier (SSID).
You can also start the WLAN wizard separately to get more information on wireless LANs within range. Select Menu >
Connect. > WLAN wiz.. Found networks are displayed.
Scroll to the desired network, select Options and from the following:
•
•
•
•
•
Start Web browsing or Cont. Web browsing — Start or continue browsing the web using the IAP of the wireless LAN.
Disconnect WLAN — Disconnect the active connection to the wireless LAN.
Refresh — Update the list of available wireless LANs.
Details — View the details of the wireless LAN.
Define access point — Create an internet access point without starting the web browser.
Always enable one of the available encryption methods to increase the security of your wireless LAN connection. Using encryption
reduces the risk of unauthorized access to your data.
Wireless LAN access points
To search for wireless LANs available within range, select Menu > Connect. > WLAN wiz.. To create an internet access point in
a wireless LAN, select Options > Define access point. To view the details of a network shown in the list, select Options >
Details.
When an application asks you to select an access point, select the created access point. You can also create an internet access
point by selecting Search for WLAN, or use Conn. mgr. to create internet access points. See "Connection manager," p. 55.
Set up a wireless LAN access point manually
If you cannot use the WLAN wizard, you can define wireless LAN access points manually.
1. Select Menu > Tools > Settings > Connection > Access points.
2. Select Options > New access point. To use an existing access point as a basis for the new one, select Use existing settings.
To start with an empty access point, select Use default settings.
3. Define the following settings.
•
•
•
Connection name — Enter a descriptive name for the connection.
Data bearer — Select Wireless LAN.
WLAN netw. name — To enter the service set identifier (SSID), that is, the name that identifies the specific wireless LAN,
select Enter manually. To select the network from the wireless LANs in range, select Search for netw..
Network status — Select Hidden if the network you are connecting to is hidden, or Public if it is not hidden.
WLAN netw. mode — If you select Infrastructure, devices can communicate with each other and with wired LAN devices
through a wireless LAN access point. If you select Ad-hoc, devices can send and receive data directly with each other, and
no wireless LAN access point is needed.
•
•
•
WLAN security mode — You must select the same security mode that is used in the wireless LAN access point. If you select
WEP (wired equivalent privacy), 802.1x, or WPA2 (Wi-Fi protected access), you must also configure the relevant additional
settings.
•
•
WLAN security sett. — Edit the security settings for the selected WLAN security mode.
Homepage — Enter the Web address of the page you want to display as a home page when you use this access point.
The settings available for editing may vary.
Advanced Internet access point settings for wireless LAN
Select Menu > Tools > Settings > Connection > Access points.
After setting up a basic Internet access point for wireless LAN, select Options > Advanced settings, and define the following
advanced settings.
•
•
•
•
•
IPv4 settings — Enter the device IP and name server addresses for the IPv4 Internet protocol.
IPv6 settings — Select or enter the name server addresses for the IPv6 Internet protocol.
Ad-hoc channel — If the selected network mode is ad-hoc, select User defined to manually enter a channel number (1-11).
Proxy serv. address — Enter the proxy server address.
Proxy port number — Enter the proxy server port number.
The settings available for editing may vary. Contact your service provider for more information.
Wireless LAN settings
© 2007 Nokia. All rights reserved.
57
12.
Web
Select Menu > Web (network service).
Web is one of the two browsers in your device. With Web, you can browse regular Web sites. These pages use the extensible
hypertext markup language (XHTML) or hypertext markup language (HTML). If you want to browse WAP pages, use Menu >
Media > Services. Both of the browsers use their own bookmarks. The links in your received messages open in the Services
browser.
Check the availability of services, pricing, and fees with your network operator or service provider. Service providers will also
give you instructions on how to use their services.
Access points
To browse the Web, you need to configure Internet access point settings. If you are using a data call or a GPRS connection, your
wireless network must support data calls or GPRS, and the data service must be activated for your SIM card. Your device might
have configured the Internet access point settings automatically based on your SIM card. If not, contact your service provider
for the correct settings.
Tip: You may receive the Internet access point settings from your service provider as a special text message or from
the network operator's or service provider's Web pages.
You can also enter the Internet access point settings manually. See "Internet access points," p. 53.
Browse the Web
To browse the Web, select a bookmark, and press the scroll key. You can also enter the Web address, and press the scroll key.
Use only services that you trust and that offer adequate security and protection against harmful software.
Tip: When you start to enter the address, addresses of pages you have previously visited that match your input are
displayed. To open a page, scroll to the address, and press the scroll key.
To open a Web link, scroll to it and press the scroll key. On a Web page, new links appear underlined in blue and previously
visited links in purple. Images that act as links have a blue border around them.
Addresses of the pages you visit are saved in the Auto. bookmarks folder.
Keyboard shortcuts:
•
•
•
•
•
•
•
•
Press 1 to open your Bookmarks.
press 2 to find text.
Press 3 to return to the previous page.
Press 5 to switch between your open browser windows.
Press 8 to open page overview.
Press 9 to go to a different Web page.
Press # to zoom out.
Press * to zoom in.
Bookmarks
Your device may have preinstalled bookmarks and links for third-party internet sites. You may also access other third-party sites
through your device. Third-party sites are not affiliated with Nokia, and Nokia does not endorse or assume liability for them. If
you choose to access such sites, you should take precautions for security or content.
To view a bookmarked Web page, scroll to the bookmark, and press the scroll key.
To browse other Web pages, select Options > Navigation options > Go to web address, enter the page address, and select Go
to.
To delete a bookmark, scroll to it, and press the backspace key.
To add a bookmark, select Menu > Web > Options > Bookmark manager > Add bookmark. If you have a Web page open,
select Options > Bookmarks > Options > Bookmark manager > Add bookmark. Scroll to Name to enter a descriptive name
for the bookmark, Address to enter the Web page address, Access point to change the access point to connect to the Web page,
and User name or Password to enter your user name and password, if required by the service provider. To save the bookmark,
select Back.
© 2007 Nokia. All rights reserved.
58
W e b
Download items
You can download different items such as ringing tones, images, operator logos, themes, and video clips. To download an item,
scroll to it, and press the scroll key. These items can be provided free, or you can purchase them. Downloaded items are handled
by the respective applications in your device.
When you start a download, a list of ongoing, paused, and completed downloads from the current browsing session is displayed.
To view the list, you can also select Options > Tools > Downloads. In the list, scroll to an item, and select Options to pause,
resume, or cancel ongoing downloads; or open, save, or delete completed downloads.
To purchase items:
1. To download the item, scroll to the link, and press the scroll key.
2. Select the appropriate option to purchase the item.
3. Carefully read all the information provided. To continue the download, select Accept. To cancel the download, select
Cancel.
End a connection
To end the connection and view the browser page offline, select Options > Advanced options > Disconnect; or to end the
connection and close the browser, select Options > Exit.
Clear the cache
A cache is a memory location that is used to store data temporarily. If you have tried to access or have accessed confidential
information requiring passwords, empty the cache after each use. The information or services you have accessed are stored in
the cache.
To clear the cache, select Options > Advanced options > Clear cache.
News feeds and blogs
Select Menu > Web > Web feeds.
Feeds are xml files in various Web pages that usually contain headlines and articles, often about recent news or other topics.
You can subscribe to interesting feeds on Web pages. Select Options > Subscribe.
Tip: Blog is a shortening of Weblog, which is a continuously updated Web diary . Often the author's personality is an
important factor in the blog.
To download a feed or blog, scroll to it, and press the scroll key.
To add a feed or blog, select Options > Manage feed > New feed, and enter the information.
To edit a feed or blog, scroll to a feed, select Options > Manage feed > Edit, and modify the information.
Web settings
Select Menu > Web > Options > Settings.
Define the following settings:
•
•
•
•
Access point — Scroll to the access point to connect to Web pages, and press the scroll key.
Load imgs. & sounds — Select No to load pages faster when browsing by not loading the images on them.
Default encoding — Select the correct character encoding for your language.
Auto. bookmarks — Select On to save Web page addresses that you visit automatically in the Auto. bookmarks folder. To hide
the folder, select Hide folder.
•
•
Screen size — Select Full screen to use the whole display area for viewing Web pages. You can press the left selection key to
open Options and use the available options while browsing in full screen mode.
Homepage — Select the page that you want to appear as your homepage. Select Default to use the access point homepage,
User defined to enter the homepage address, or Use current page to use the currently open Web page.
Mini map — Select whether you want to see an overview of the page as a miniature on top of the page you are viewing.
History list — Select whether you want to see miniatures of the pages you have visited when you want to go back in your
browsing history.
•
•
•
Cookies — Select to allow or reject the sending and receiving of cookies. Cookies are info the network server collects about
your visits to various Web pages. They are necessary if you shop on the Web (for example, to retain the items you buy until
you reach the cashier page). However, the information may be misused (for example, you may receive unwanted
advertisements in your device).
•
•
Java/ECMA script — Some Web pages may include program commands that affect the appearance of the page or interaction
between the page and its browsers. To deny the use of such scripts, select Disabled (for example, if you have trouble
downloading).
Security warnings — Select Show or Hide to see or hide the security warnings you may receive during browsing.
© 2007 Nokia. All rights reserved.
59
W e b
•
Block pop-ups — Select whether you want to allow pop-ups. Some pop-ups may be necessary (for example, smaller windows
where you write e-mails in Web-based mail systems), but they may also contain unwanted advertising.
Services
Select Menu > Media > Services (network service).
Services is one of the two browsers in your device. With Services, you can browse WAP pages that have been designed specially
for mobile devices. For example, operators may have WAP pages for mobile devices. To browse regular Web pages, use the other
browser in Menu > Web.
Check the availability of services, pricing, and fees with your network operator or service provider. Service providers will also
give you instructions on how to use their services.
Tip: To start a connection, press and hold 0 in the standby mode.
© 2007 Nokia. All rights reserved.
60
13.
Office applications
Office folder contains tools that help you organize and manage the details of different events in your personal and business life.
Some applications in the Office folder are not available in all languages.
Opening a large file may not be possible or it may take a while.
File manager
With File mgr., you can manage the contents and properties of files and folders. You can open, create, move, copy, rename, and
search for files and folders. Copyright protection may prevent sending some files.
Manage files
To open a file, scroll to it, and press the scroll key.
Tip: To select multiple files, scroll to each file, and simultaneously press the shift key and scroll key to mark it. After you
have marked all desired files, select Options and the desired command.
To send a file, scroll to the file, and select Options > Send.
To delete a file, scroll to the file, and select Options > Delete.
To organize files or folders, scroll to the file or folder, and select Options > Move to folder. Default folders such as sound clips
in gallery cannot be moved or deleted.
Tip: To copy the file or folder to another folder, select Options > Copy to folder. To create a new folder to organize
your files, select Options > New folder.
To rename a file or folder, scroll to the desired file or folder, and select Options > Rename. Enter the new name, and select
OK.
To receive a file using an infrared connection, select Options > Receive via infrared.
To view information about files, scroll to the desired file, and select Options > View details.
To check the memory consumption in device memory or a memory card, select Options > Memory details.
Search for files
1. To search for files, select Options > Find.
2. Select the memory you want to search.
3. Enter the search text, and press the scroll key. The folders and files whose names contain the search text are displayed.
4. Select Options > Find to conduct another search.
Quickoffice
To use the Quickoffice applications, select Menu > Office > Quickoffice. A list of files in the .doc, .xsl, .ppt, and .txt file formats
saved in your device memory or the memory card opens.
To open a file in its respective application, press the scroll key.
To edit a file, open the file, and press the scroll key.
To sort files, select Options > Sort by.
To open Quickword, Quicksheet, or Quickpoint, scroll to the desired tab with the scroll key.
Not all file formats or features are supported.
For more information, see the device help.
Quickword
With Quickword, you can view and edit Microsoft Word documents on the display of your device. Quickword supports colors,
bold, and underline.
Quickword supports the viewing and editing of documents saved in .doc format in Microsoft Word 97, 2000, and XP. Not all
variations or features of the mentioned file formats are supported.
To move to the previous or next page in the document, scroll up or down.
To move up or down one line, scroll left or right.
To search the document for text, select Options > Search options.
© 2007 Nokia. All rights reserved.
61
O f f i c e a p p l i c a t i o n s
You can also select Options and from the following:
•
•
•
Go to — Move to the start, end, or selected position within the document.
Zoom — Zoom in or out.
Start auto-scroll — Start automatic scrolling through the document. To stop scrolling, select Options > Stop auto-scroll.
To edit the document, press the scroll key. Select Edit, and from the available options. You can, for example, align text, change
the font and font color, and add bullets and indentations.
Quicksheet
With Quicksheet, you can read and edit Microsoft Excel files on the display of your device.
Quicksheet supports the viewing and editing of spreadsheet files saved in .xls format in Microsoft Excel 97, 2000, and XP. Not
all variations or features of the mentioned file formats are supported.
To move around in the spreadsheet, use the scroll key.
To switch between worksheets, select Options > Worksheet.
To search the spreadsheet for a text, value, or formula, select Options > Search options.
To change how the spreadsheet is displayed, select Options and from the following:
•
Pan — Navigate within the current worksheet by blocks. A block contains columns and rows displayed by a screen. To display
the columns and rows, scroll to a block and select OK.
•
•
•
Resize — Adjust the size of columns or rows.
Zoom — Zoom in or out
Freeze panes — Keep the selected row, column, or both visible while you move in the spreadsheet.
To edit the spreadsheet, press the scroll key. Select Edit, and from the available options. You can, for example, format text and
cells, insert mathematical operators and spreadsheet functions, and change the background color.
Quickpoint
With Quickpoint, you can view and edit Microsoft PowerPoint presentations on the display of your device.
Quickpoint supports the viewing and editing of presentations created in .ppt format in Microsoft PowerPoint 2000 and XP. Not
all variations or features of the mentioned file formats are supported.
To move between the slide, outline, and the notes view, scroll to the desired tab with the scroll key.
To move to the next or previous slide in the presentation, scroll up or down with the scroll key.
To view the presentation in full screen, select Options > Full screen. To zoom out, press 1. To zoom in, press 2.
To expand items in the presentation in the outline view, select Options > Expand.
To edit the presentation, press the scroll key. Select Edit, and from the available options. You can, for example, align text, change
the font and font color, and add bullets and indentations.
Print
You can print a message or file from the device, preview a print job, define page layout options, select a printer, or print to a
file. You may not be able to print all messages, such as multimedia messages or other special messages.
To configure a printer for your device, select Menu > Office > Printers > Options > Add. To set the printer as the default
printer, open a document, such as a note, and select Options > Printing options > Printers > Options > Set as default.
Before you print, make sure that your device is properly connected to the printer.
To print a message or a file, select Options > Printing options > Print.
To print to a file, select Options > Printing options > Print > Print to file, and determine the location for the file.
To change the printing options, select Options > Printing options. You can select the printer you want to use, the number of
copies and the range of pages you want to print.
To change the page layout before printing, select Options > Printing options > Page setup. You can change the paper size and
orientation, define the margins, and insert a header or a footer.
To preview a file or message before you print, select Options > Printing options > Preview.
Notes
Select Menu > Office > Notes.
You can create and send notes to other compatible devices, and save plain text files (.txt format) that you receive to Notes.
To write a new note, select Options > New note, write the text and press Done.
© 2007 Nokia. All rights reserved.
62
O f f i c e a p p l i c a t i o n s
In the Notes main view, the following options are available:
•
•
•
•
•
•
Open — Open the selected note.
Send — To send the selected note, select one of the sending methods.
New note — Create a new note.
Delete — Delete the selected note.
Mark/Unmark — Select a note or multiple notes, and apply the same rule to each.
Synchronisation — Select Start to initialize synchronization or Settings to define the synchronization settings for the note.
When viewing a note, select Options > Find to search the note for a phone number, Internet telephone address, e-mail or Web
address.
Calculator
Note: This calculator has limited accuracy and is designed for simple calculations.
Select Menu > Office > Calculator.
To make a calculation, enter the first number of the calculation. Scroll to and select a function such as add or subtract from the
function map. Enter the second number of the calculation, and select =. Use the keyboard to enter decimal points.
The calculator performs operations in the order they are entered. The result of the calculation remains in the editor field and
can be used as the first number of a new calculation.
To save the results of a calculation, select Options > Memory > Save. The saved result replaces the previously stored number
in memory.
To retrieve the results of a calculation from memory and use them in a calculation, select Options > Memory > Recall.
To view the last saved result, select Options > Last result.
Exiting the calculator application or turning off the device does not clear the memory. You can recall the last saved result the
next time you open the calculator application.
Converter
Select Menu > Office > Converter.
The converter has limited accuracy, and rounding errors may occur.
Convert measurements
1. Scroll to the Type field, and select Options > Conversion type to open a list of measures. Scroll to the measure you want to
use, and select OK.
2. Scroll to the first Unit field, and select Options > Change currency. Select the unit from which you want to convert, and select
OK. Scroll to the next Unit field, and select the unit to which you want to convert.
3. Scroll to the first Amount field, and enter the value you want to convert. The other Amount field changes automatically to
show the converted value.
Set base currency and exchange rate
Note: When you change base currency, you must enter new exchange rates because all previously set exchange rates
are cleared.
Before you can make currency conversions, you must choose a base currency and add exchange rates. The rate of the base
currency is always 1. The base currency determines the conversion rates of the other currencies.
1. To set the rate of exchange for the unit of currency, scroll to the Type field, and select Options > Currency rates.
2. A list of currencies opens, and you can see the current base currency at the top. Scroll to the currency type and enter the
exchange rate you would like to set per single unit of currency.
3. To change the base currency, scroll to the currency, and select Options > Set as base curr..
4. Select Done > Yes to save the changes.
After you have inserted all the necessary exchange rates, you can make currency conversions.
Screen export
You can show the screen of the device to an audience with a compatible data projector, or other compatible projection system.
The screen content is transferred to the data projector using, for example, a Bluetooth connection.
Select Menu > Office > Scr. export.
To be able to show screen content with a compatible data projector, you must install the drivers of the data projector. For more
information, check with the data projector manufacturer or its representative.
© 2007 Nokia. All rights reserved.
63
O f f i c e a p p l i c a t i o n s
Not all applications support this feature. You can start the external viewer in two ways: from the Office folder or inside an
application that supports it.
Show screen content
To show screen content with a data projector, open the screen export application, and select Options > Select device. In the
list of available devices, scroll to the device you want to use, and select OK. Select Options > Enable to show screen content.
To hide the screen content, select Options > Hide. The screen exporter application is moved to the background.
To stop showing screen content, select Options > Disable.
PDF reader
Select Menu > Office.
With PDF reader you can read PDF documents on the display of your device; search for text in the documents; modify settings,
such as zoom levels and page views; and send PDF files using e-mail.
Zip manager
Select Menu > Office.
With Zip manager, you can create new archive files to store compressed ZIP formatted files; add single or multiple compressed
files or directories to an archive; set, clear, or change the archive password for protected archives; and change settings, such as
compression level, temporary file drive, file name encoding, default drive, and default start-up view.
You can store the archive files on the device memory or on a memory card.
© 2007 Nokia. All rights reserved.
64
14.
Data and software management
Application manager
Important: Only install and use applications and other software from trusted sources, such as applications that are
Symbian Signed or have passed the Java Verified™ testing.
Select Menu > Installat. > App. mgr..
When you open the application manager, you see all the software packages that have been installed, with their name, version
number, type, and size. You can view the details of installed applications, remove them from your device, and specify installation
settings.
Install applications and software
You can install two types of applications and software on your device:
•
•
Applications and software specifically intended for your device or compatible with the Symbian operating system. These
software installation files have the extension .sis.
J2ME™ applications compatible with the Symbian operating system. The Java application installation file extensions are .jad
or .jar.
Installation files may be transferred to your device from a compatible computer, downloaded during browsing, or sent to you
in a multimedia message, as an e-mail attachment, or with Bluetooth. If you use Nokia PC Suite to transfer a file to your device,
save the file in the C:\nokia\installs folder in your device.
During installation, the device checks the integrity of the package to be installed. The device shows information about the checks
being carried out, and you are given options to continue or cancel the installation.
If you install applications that require a network connection, note that the power consumption of your device may increase
when you use these applications.
View and remove software
You can view the details of installed applications or remove them from your device.
To view the details of an installed software package, select the application and Options > View details.
To remove software, open the application manager main view and select Options > Remove.
If you remove software, you can only reinstall it by using the original software package file, or by restoring a full backup that
contains the removed software package. If you remove a software package, you may no longer be able to open files created
with that software. If another software package depends on the software package that you removed, the other software package
may stop working. Refer to the documentation of the installed software package for details.
View the installation log
To view the installation log, select Options > View log. A list shows what software has been installed and removed, and the
date of installation or removal. If you encounter problems with the device after installing a software package, you can use this
list to find out which software package may be the cause of the problem. The information in this list may also help to pinpoint
problems that are caused by software packages that are incompatible with each other.
Settings
To modify installation settings, select Options > Settings and from the following:
•
•
•
Software installation — Select to install signed applications only or all applications.
Online certif. check — To check the validity of certificates when an application is installed, select On.
Default web address — The validity of a certificate is checked from the default address if the certificate does not include its
own Web address.
Specify Java application security settings
To specify security settings for a Java application, select Options > Suite settings.
You can define which functions the Java application can access. The value that you can set for each functionality depends on
the protection domain of the software package.
•
•
•
•
Network access — Create a data connection to the network.
Messaging — Send messages.
App. auto-start — Open the application automatically.
Connectivity — Activate a local data connection, such as a Bluetooth connectivity.
© 2007 Nokia. All rights reserved.
65
D a t a a n d s o f t w a r e m a n a g e m e n t
•
•
•
Multimedia — Take pictures or record videos or sound.
Read user data — Read your calendar entries, contacts, or any other personal data
Edit user data — Add personal data, such as entries to your address book.
You can define how you will be prompted to confirm Java application access to device functions. Select one of the following
values:
•
•
•
•
Ask every time — Require the Java application to ask for your confirmation each time it uses the functionality.
Ask first time — Require the Java application to ask for initial confirmation to use the functionality.
Always allowed — Allow the Java application to use the functionality without your confirmation.
Not allowed — Prevent the Java application from using the functionality.
The security settings help protect your device against harmful Java applications that may use the functions of your device without
your permission. Only select Always allowed if you know the supplier and trustworthiness of the application.
Remote configuration network service
Select Menu > Connect. > Dev. mgr..
You normally receive server profiles and different configuration settings from your network operator, service providers, and
company information management department. Configuration settings may include connection and other settings used by
different applications in your device. The available options may vary.
The remote configuration connection is usually started by the server when the device settings need to be updated.
Remote configuration settings
In the Dev. mgr. main view, select Options and select from the following:
•
•
•
•
•
Start configuration — Connect to the server and receive configuration settings for your device.
New server profile — Create a new server profile.
Edit profile — Change the profile settings.
Delete — Remove the selected profile.
Enable config. — Select to receive configuration settings from those servers for which you have a server profile and have
allowed configuration.
•
•
Disable config. — Select to stop receiving configuration settings from all servers for which you have a server profile.
View log — View the configuration log of the selected profile.
Create a configuration profile
To create a new configuration server profile, select Options > New server profile and select from the following settings. Ask
your service provider for the correct values.
•
•
•
•
•
Server name — Enter a name for the configuration server.
Server ID — Enter the unique ID to identify the configuration server.
Server password — Enter a password to identify your device to the server.
Session mode — Select the preferred connection type.
Access point — Select the access point to use for the connection, or create a new access point. You can also choose to be
asked for the access point every time you start a connection.
•
•
•
•
•
•
Host address — Enter the Web address of the configuration server.
Port — Enter the port number of the server.
User name — Enter your user ID for the configuration server.
Password — Enter your password for the configuration server.
Allow configuration — Select Yes to allow the server to initiate a configuration session.
Auto-accept all reqs. — Select Yes if you do not want the server to ask for your confirmation when it initiates a configuration
session.
•
Network authentic. — To authenticate your device to the network before synchronizations, select Yes. Key in your Network
user name and Network password.
Data synchronization
Menu > Connect. > Sync.
Use Sync to synchronize (network service) your contacts, calendar, or notes with corresponding applications on a compatible
computer or remote Internet server. Your synchronization settings are saved in a synchronization profile. The application uses
SyncML technology for remote synchronization. For information on SyncML compatibility, contact the supplier of the applications
with which you want to synchronize your device.
The available applications you can synchronize may vary. Contact your service provider for more information.
Tip: You may receive the synchronization settings as a message from your service provider.
© 2007 Nokia. All rights reserved.
66
D a t a a n d s o f t w a r e m a n a g e m e n t
Create a synchronization profile
To create a profile, select Options > New sync profile.
The device asks whether to use the synchronisation profile for PC Suite. If you select to use the PC Suite settings, it is not necessary
to modify the synchronization profile settings. If you want to modify the settings, select from the following options:
•
•
•
Sync profile name — Enter a name for the profile.
Applications — Select the applications to synchronize with the profile.
Connection settings — Specify the needed connection settings. Contact your service provider for information.
To edit an existing profile, select Options > Edit sync profile.
Synchronization profiles
In the Sync main view, select Options and select from the following options:
•
•
Synchronise — Synchronize the data included in the selected profile with a remote database.
New sync profile — Create a synchronization profile. You may want to create multiple synchronization profiles for an
application to vary the data bearer in use or remote database with which you synchronize your device.
View log — View the added, updated, and deleted entries in the latest synchronization with the profile.
Delete — Remove the selected profile.
•
•
Synchronization connection settings
To create the connection settings of a new profile, select Options > New sync profile > Connection settings and select from
the following options:
•
•
•
•
Server version — Select the SyncML version you can use with your server.
Server ID — Enter the server ID of your server. This setting is only available if you select 1.2 as the SyncML version.
Data bearer — Select the data bearer to connect to the remote database during synchronization.
Access point — Select the access point to use for the synchronization connection, or create a new access point. You can also
choose to be asked for the access point every time you start synchronizing.
Host address — Enter the Web address of the server that contains the database with which you want to synchronize your
device.
•
•
•
•
•
•
Port — Enter the port number of the remote database server.
User name — Enter your user name to identify your device to the server.
Password — Enter your password to identify your device to the server.
Allow sync requests — To allow synchronization to start from the remote database server, select Yes.
Accept all sync reqs. — To have your device ask for your confirmation before accepting synchronization from the server, select
No.
•
Network authentic. — To authenticate your device to the network before synchronization, select Yes. Enter your network
user name and network password.
Define synchronization settings for Contacts
To define the synchronization settings for the Contacts application, scroll to the desired profile, and select Options > Edit sync
profile > Applications > Contacts and select from the following options:
•
•
•
Include in sync — Select whether to synchronize your contacts directory with this synchronization profile.
Remote database — Enter the path to the database with which you synchronize your contacts directory.
Local database — If you have more than one contacts directory in your device, select the one you want to synchronize with
this synchronization profile.
•
Synchronisation type — Select the direction of synchronization. Scroll to Normal to synchronize data from the device to
remote database and back, To phone only to synchronize data from the remote database to your device, or To server only to
synchronize data from your device to the remote database.
Define synchronization settings for Calendar
To define the synchronization settings for the Calendar application, scroll to the desired profile, and select Options > Edit sync
profile > Applications > Calendar and select from the following options:
•
•
•
Include in sync — Select whether to synchronize your calendar with this synchronization profile.
Remote database — Enter the path to the database with which you synchronize your calendar.
Local database — If you have more than one calendar in your device, select the one you want to synchronize with this
synchronization profile.
•
Synchronisation type — Select the direction of synchronization. Scroll to Normal to synchronize data from the device to
remote database and back, To phone only to synchronize data from the remote database to your device, or To server only to
synchronize data from your device to the remote database.
© 2007 Nokia. All rights reserved.
67
D a t a a n d s o f t w a r e m a n a g e m e n t
Define synchronization settings for Notes
To define the synchronization settings for the Notes application, scroll to the desired profile, and select Options > Edit sync
profile > Applications > Notes and select from the following options:
•
•
•
Include in sync — Select whether to synchronize your notes with this synchronization profile.
Remote database — Enter the path to the database with which you synchronize your notes.
Local database — If you have more than one Notes application in your device, select the one you want to synchronize with
this synchronization profile.
•
Synchronisation type — Select the direction of synchronization. Scroll to Normal to synchronize data from the device to
remote database and back, To phone only to synchronize data from the remote database to your device, or To server only to
synchronize data from your device to the remote database.
Download!
Select Menu > Download!.
Download! (network service) is a mobile content shop available on your device. You can browse, download, and install items,
such as latest applications and related documents, to your device from the web.
The items are categorized under catalogs and folders provided by Nokia or independent service providers. Some items may be
chargeable, but you can usually preview them free of charge.
Only install and use applications and other software from sources that offer adequate security and protection against harmful
software.
If Download! is not available from your wireless service provider, it may not appear in the menu of your device. For more
information on the availability of Download!, contact your network operator, service provider, or dealer.
Select catalogs, folders, and items
Download! uses your network services to access the most updated content. For information on additional items available
through Download!, contact your network operator, service provider, or the supplier or manufacturer of the item.
To open an item or view the content of a folder or a catalog, scroll to it, and press the scroll key.
Select Options, and from the following:
•
•
•
•
•
•
•
•
Refresh list — Update the content in Download!.
Hide — Hide a folder or a catalog from the list, for example, to view only items that you use frequently.
Show all — Make all the hidden items visible.
Buy — Buy the selected item. A submenu opens, where you can select the version of the item, and view price information.
Get — Download an item that is free of charge.
View details — View the details of the selected item.
Settings — Adjust the Download! settings.
Homepage — Return to the Download! main level.
The available options may vary depending on your service provider, the selected item, and the view you are in.
Download! settings
To select which access point is used to connect to the service provider’s server, and whether to have the device to ask for the
access point every time you use Download!, select Access point.
To define whether you want the downloaded item or application to open automatically after download is completed, select
Automatic open.
To define whether you want the preview confirmation query to be shown before previewing an item, select Preview
confirmation.
To define whether you want the purchase confirmation query to be shown before buying an item, select Buy confirmation.
Settings Wizard
Select Menu > Tools > Sett. wizard.
Settings Wizard configures your device for operator (MMS, GPRS, and Internet) and e-mail settings based on your network
operator information.
To use these services, you may have to contact your network operator or service provider to activate a data connection or other
services.
If Settings Wizard is not available from your wireless service provider, it may not appear in the menu of your device. For more
information on the availability of Settings Wizard, contact your network operator, service provider, or dealer.
The availability of different settings items in Settings Wizard depends on the features of the device, SIM card, wireless service
provider, and the availability of the data in the Settings Wizard database.
© 2007 Nokia. All rights reserved.
68
D a t a a n d s o f t w a r e m a n a g e m e n t
When you use the wizard for the first time you are guided through settings configuration. To start the wizard, select Start.
If there is no SIM card inserted, you will be asked to select the home country of your wireless service provider, and your service
provider. If the country or service provider suggested by the wizard is not the correct one, select the correct one from the list.
To access the main view of the Settings Wizard after the wizard has finished the settings configuration, select OK.
If the settings configuration is interrupted, the settings will not be defined. After closing the wizard, you can start to use the
configured applications.
To configure operator-specific settings such as, for example, MMS, Internet, WAP, and streaming settings, select Options >
Operator.
To configure e-mail settings, select Options > E-mail settings.
© 2007 Nokia. All rights reserved.
69
15.
Camera
You can take photos or record video clips with the built-in camera. The camera lens is on the back of the device, and the display
works as a viewfinder. The camera produces pictures in .jpeg format and video clips in .3gpp format.
Take a picture
1. Select Menu > Media > Camera.
Your device supports an image capture resolution of up to 1600 x 1200 pixels.
2. Use the display as a viewfinder, aim at your subject, and press the scroll key. The device saves the photo in the default folder,
or in the folder you have defined.
Tip: To zoom in or out before taking a picture, scroll up or down.
3. If you do not want to keep the saved photo, select Options > Delete. Select Back to return to the viewfinder to take another
picture. Select Options > Go to Gallery to view the photo in Gallery.
If the light is dim, select Options > Night mode after you have opened Camera but before taking a picture.
To adjust the image, select Options > Adjust > White balance or Colour tone.
To take pictures in a sequence, select Options > Sequence mode. The camera takes six pictures in a row.
To take timed pictures, select Options > Self-timer, select the desired timeout, and press Activate. The camera takes a picture
after the timeout has passed.
Tip: You can view photos in Menu > Media > Gallery > Images.
Record a video clip
Select Camera, and scroll right to activate the video recorder. To start recording a video clip, press the scroll key. The remaining
recording time is shown on the top of the display. To pause the recording, select Pause; to resume the recording, select
Continue. To stop the recording, select Stop. The device saves the clip in the default folder, or in the folder you have defined. If
you do not want to keep the saved video clip, select Options > Delete. Select Back to return to the viewfinder to record another
video clip. Select Options > Play to view the video clip in the RealPlayer application.
Insert pictures into messages
When you are creating a new multimedia message, you can open the camera to insert a new picture into the message.
To insert a picture into a multimedia message, select Options > Insert new > Image. The viewfinder shows you the image to
be captured. To take a picture, press the scroll key. To insert the picture in the message, press the scroll key.
Insert videos into messages
When you are creating a new multimedia message, you can open the camera to insert a new video into the message.
To insert a video into a multimedia message, select Options > Insert new > Video clip. Press the scroll key to start recording.
To insert the video in the message, select Options > Select.
Settings
To edit the image settings, select Menu > Media > Camera > Options > Settings > Image, and define the following:
•
Image quality — Define how much the picture is compressed when being saved. High provides the best image quality, but
takes more memory. Normal is the default quality setting. Basic takes the least amount of memory.
Show captured img. — Select whether you want the captured image to be displayed after the capture.
Image resolution — Select the resolution of the images you capture.
•
•
•
Default image name — Select Date or Text for the default title assigned to a picture. Date assigns the date of the capture as
the title. Text assigns the term you define and a number to the picture.
•
Memory in use — Select the memory to use for storing images: Phone memory or Memory card.
To edit the video settings, select Options > Settings > Video, and define the following:
•
Length — Select the length of the video clips that you record. The maximum length of a video clip depends on the available
memory.
•
Video resolution — Select the resolution to use during video recording. The default setting for the resolution is always the
lowest setting.
© 2007 Nokia. All rights reserved.
70
C a m e r a
•
•
Default video name — Select Date or Text for the default title assigned to a recorded video. Date assigns the date of the
recording as the title. Text assigns the term you define and a number to the recorded video.
Memory in use — Select the memory to use for storing recorded videos: Phone memory or Memory card.
© 2007 Nokia. All rights reserved.
71
16.
Media applications
Select Menu > Media.
Media contains different media applications that allow you to save and view images, record sounds, and play sound clips.
Gallery
Select Menu > Media > Gallery.
Use Gallery to access and use different types of media, including images, videos, music, and sounds. All viewed images and
videos and all received music and sounds are automatically saved to Gallery. You can browse, open, and create folders; and
mark, copy, and move items to folders. Sound clips are opened in the Music Player, and video clips and streaming links in the
RealPlayer application.
To open a file or a folder, press the scroll key. Images are opened in the image viewer.
To download files into the Gallery in one of the main folders using the browser, select Graphic downl., Video downl., Track
downl., or Sound downl.. The browser opens, and you can choose a bookmark or enter the address for the site to download
from.
To search for a file, select Options > Find. Start to enter a search string (for example, the name or date of the file you are
searching for). Files that match the search are shown.
Images
Select Menu > Media > Gallery > Images.
Images consists of two views:
•
•
In the image browser view you can send, organize, delete, and rename images stored in your device or memory card.
In the image viewer, which opens when you select an image in the image browser view, you can view, and send individual
images. You can set images as wallpaper for your display.
The following file formats are supported: JPEG, BMP, PNG, and GIF 87a/89a. The device does not necessarily support all variations
of the file formats.
To open an image for viewing, select an image in the image browser view, and select Options > Open. The image opens in the
image viewer.
To open the next or previous image for viewing, scroll right or left in the image viewer.
To enlarge the viewed image on the display, select Options > Zoom in, or press 5 or 7. To reduce the viewed image on the
display, select Zoom out or press 0.
To view the image in full screen size, select Options > Full screen or press 7 twice. To return to normal view, select Options >
Normal screen.
To rotate an image, select an image, and Options > Rotate. Select Right to rotate the image clockwise by 90 degrees, or select
Left to rotate the image counterclockwise by 90 degrees.
Manage image files
To view detailed information about an image, select an image and Options > View details. Size and format of the file, the time
and date the file was last modified and the resolution of the image in pixels are displayed.
To send an image, select the image, Options > Send, and the method for sending.
To rename an image, select an image and Options > Rename. Enter a new name, and select OK.
To set an image as wallpaper, select the image and Options > Set as wallpaper.
To add an image to a contact card, select an image and Options > Add to contact. The contacts view opens, and you can select
the contact for the image.
Organizing images
To create folders to organize your images, select Options > Organise > New folder. Enter a name for the folder, and select
OK.
To copy or move files, select a file and Options > Organise > Move to folder, New folder, Move to memory card, Copy to memory
card, Copy to phone mem., or Move to phone mem..
RealPlayer
Select Menu > Media > RealPlayer.
© 2007 Nokia. All rights reserved.
72
M e d i a a p p l i c a t i o n s
RealPlayer can play video clips and audio files that are stored in the device memory or on a memory card, transferred to your
device from e-mail or compatible PC, or streamed to your device over the Web.
Formats supported by RealPlayer include MPEG-4, MP4 (not streaming), 3GP, RV, RA, AAC, AMR, and Midi. RealPlayer does not
necessarily support all variations of a media file format.
Tip: Streaming audio and video files means playing them directly from the Web without downloading them first to
your device.
Play video clips and stream links
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely
loud.
To select audio and video files to play with RealPlayer, select Options > Open, and scroll to a media clip in your device or on a
memory card.
To play streaming media, select a Web link that points to a media clip, and select Play; or connect to the Web, browse to a video
clip or audio file, and select Play. RealPlayer recognizes two kinds of links: an rtsp:// URL and an http:// URL that points to a RAM
file. Before the content begins streaming, your device must connect to a Web site and buffer the content. If a network connection
problem causes a playback error, RealPlayer attempts automatically to reconnect to the Internet access point.
To play audio and video files stored in your device or on a memory card, select the file and Play.
To stop playback or streaming, select Stop. Buffering or connecting to a streaming site stops, playback of a clip stops, and the
clip rewinds to the beginning.
To view the video clip in full-screen size, select Options > Play in full screen. The size of the video area changes to normal or
full screen. Full screen increases the size of the video to cover the maximum video area possible while the aspect ratio is
maintained.
To save a media clip, select Options > Save, scroll to a folder in device memory or on a memory card, and select Save. To save
a link to a media file on the Web, select Save link.
To fast-forward or rewind the clip during playback, scroll up or down.
Tip: To fast-forward during play, scroll up and hold. To rewind during play, scroll down and hold.
To increase or decrease the volume during playback, press the volume keys.
Send audio files and video clips
You can transfer a media clip to another device or attach a media clip to a multimedia message, document, or slide presentation.
To transfer a media clip through infrared or Bluetooth connection, select a clip and Options > Send. Select a method to use to
send the clip to another device.
To send a media clip inside a message, create a multimedia message, select a clip to attach and Insert object > Video clip or
Sound clip.
To remove a media clip you inserted, select Options > Remove > Yes.
Receive videos
Select Menu > Messaging. Open a message that contains a video clip. Scroll to the clip, and press the scroll key.
Select Pause or Stop, select Options, and:
•
•
Play — Play the clip from the start.
Play in full screen — Play the clip in full screen mode. Landscape style clips will be rotated by 90 degrees. To switch back to
normal view, press any key.
•
•
•
•
•
•
Continue — Resume playing the clip.
Continue in full scr. — Continue playing the clip in full screen mode.
Mute — Mute the sound of the video clip. To turn sound back on, scroll right.
Save link — Save the Web link to a clip.
Clip details — View information such as the clip duration and size.
Settings — Change video or connection settings.
The available options may vary.
View information about a media clip
To view the properties of a video clip, audio file, or Web link, select the clip, and select Options > Clip details. Information may
include the bit rate or the Internet link of a streaming file.
© 2007 Nokia. All rights reserved.
73
M e d i a a p p l i c a t i o n s
Settings
Select Menu > Media > RealPlayer > Options > Settings.
Video settings
Select Loop > On, if you want to replay video clips automatically after they finish playing.
Connection settings
Select Connection, scroll to the following settings, and press the scroll key to edit:
•
•
Proxy — Select whether to use a proxy server and to key in the proxy server's IP address and port number.
Network — Change the access point to connect to the Internet and to set the port range used when connecting.
Proxy settings
Proxy servers are intermediate servers between media servers and their users. Some service providers use them for additional
security or to speed up access to Web pages that contain media files.
Contact your service provider for the correct settings.
Select Connection > Proxy, scroll to the following settings, and press the scroll key to edit:
•
•
•
Use proxy — Select Yes to use a proxy server.
Proxy serv. address — Enter the IP address of the proxy server. This setting is only available if you select to use a proxy server.
Proxy port number — Enter the port number of the proxy server. This setting is only available if you select to use a proxy
server.
Network settings
Contact your service provider for the correct settings.
Select Connection > Network, scroll to the following settings, and press the scroll key to edit:
•
•
Default access point — Scroll to the access point to connect to the Internet, and press the scroll key.
Online time — Set the time when RealPlayer disconnects from the network when you pause a media clip that plays using a
network link. Select User defined, and press the scroll key. Enter the time, and select OK.
•
•
Lowest UDP port — Enter the lowest port number of the server port range. The minimum value is 1024.
Highest UDP port — Enter the highest port number of the server port range. The maximum value is 65535.
Advanced network settings
To edit the bandwidth values for different networks, select Connection > Network > Options > Advanced settings.
To select the bandwidth for any of the listed networks, scroll to its setting, and press the scroll key. Scroll to the desired value,
and select OK.
To enter the bandwidth yourself, select User defined.
Contact your service provider for the correct settings.
To save settings, select Back.
Music player
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely
loud.
Select Menu > Media > Music player.
With the music player, you can play music files and create and listen to track lists. The music player supports files with extensions
such as MP3 and AAC.
Listen to music
Warning: Listen to music at a moderate level. Continuous exposure to high volume may damage your hearing.
To select a music track, select Options > Music library. All tracks lists all music on your device. To view sorted songs, select
Albums, Artists, Genres, or Composers. To play a track, scroll to the track, and select Options > Play. When a track is playing, to
change between play and pause, press and . To stop a track, press
.
After you add or remove music files in the device, update your Music library. Select Options > Update Music library. The player
searches the device memory for music files and updates them to the Music library.
To select the previous or next track, scroll the scroll key up or down.
To play the music tracks repeatedly, select Options > Loop. Select All to repeat all the tracks in the current folder, One to repeat
the selected track, or Off to set off the repeating.
To play music in random order, select a folder and Options > Random play.
© 2007 Nokia. All rights reserved.
74
M e d i a a p p l i c a t i o n s
To view music track information, scroll to the desired track and select Options > View details.
To set a music track as a ringing tone for all profiles, scroll to the desired track and select Options > Set as ringing tone.
Keyboard shortcuts:
•
•
Press 5 to pause a track.
press 4 to return to the beginning of the track. Press within two seconds after a song has started to go to the previous track.
Press and hold to rewind.
Press 6 to go to the next track. Press and hold to fast forward.
Press 8 to stop a track.
•
•
Adjust music volume
To control the music volume, press the volume keys. To mute the volume, press the lower volume key until the volume is muted.
Track lists
You can create a new track list and add tracks to it, or select a saved track list.
To create a new track list, select Options > Music library > Track lists > Options > New track list. Write the name of the new
track list, and select OK.
To add a track to a track list, open the track list, and select Options > Add tracks.
Equalizer
Select Menu > Media > Music player > Options > Equaliser.
You can personalize the sound of your music files with Equaliser. You can use preset frequency settings based on styles of music,
like classical or rock. You can also create customized settings based on your own listening preferences.
You cannot use other functions of Music player while Equaliser is open.
With Equaliser, you can enhance or diminish frequencies during music playback and modify how your music sounds. There are
preset frequency settings in your device, for example Rock.
To use a preset frequency setting when playing music, scroll to the frequency setting you want to use, and select Options >
Activate.
Create your own frequency setting
1. To create your own frequency setting, select Options > New preset.
2. Enter a name for the preset frequency setting, and select OK.
3. Scroll up or down to move between the frequency bands and set the frequency on each band. To move between bands, scroll
left or right.
4. Select Back to save the new frequency setting or select Options > Reset to defaults to set the bands at a neutral frequency
and start over.
To edit a preset frequency setting, select Options > New preset or Options > Edit.
To modify the frequency of a preset setting, scroll to the frequency bands, and scroll up or down to increase or decrease their
values. You hear your frequency adjustment immediately in the playback.
To reset the frequency bands to their original values, select Options > Reset to defaults.
To save your new or edited settings, select Back.
Recorder
Select Menu > Media > Recorder.
With Recorder, you can record up to 60 seconds of a voice memo, save the voice recording as a sound clip, and play the sound
clip. Recorder supports the AMR format.
Press the voice key to activate Recorder. If you have logged in to push to talk, the voice key works as a push to talk key and does
not activate Recorder.
To record a voice memo, selectOptions > Record sound clip. Select Pause to pause the recording andRecord to resume recording.
When you finish recording, select Stop. The sound clip is automatically saved.
The maximum length of a voice recording is 60 seconds, but it also depends on the storage space available in device memory
or on a memory card.
© 2007 Nokia. All rights reserved.
75
M e d i a a p p l i c a t i o n s
Play a voice recording
To listen to a voice recording that you just recorded, select the play icon ( ). Select Stop to cancel playback. The progress bar
displays the playing time, position, and length of a voice recording.
To pause playback of a voice recording, select Pause. Playback resumes when you select Play.
Voice recordings that you receive or record are temporary files. You must save the files that you want to keep.
Flash player
Select Menu > Media > Flash Player.
With Flash Player, you can view, play, and interact with flash files made for mobile devices.
To open a folder or play a flash file, scroll to the folder or file, and press the scroll key.
To send a flash file to compatible devices, scroll to it, and press the call key. Copyright protection may prevent the sending of
some flash files.
To switch between flash files saved on your device memory or memory card, scroll left or right.
The available options may vary.
© 2007 Nokia. All rights reserved.
76
17.
GPS applications
The Global Positioning System (GPS) is operated by the government of the United States, which is solely responsible for its
accuracy and maintenance. The accuracy of location data can be affected by adjustments to GPS satellites made by the United
States government and is subject to change with the United States Department of Defense civil GPS policy and the Federal
Radionavigation Plan. Accuracy can also be affected by poor satellite geometry. Availability and quality of GPS signals may be
affected by your location, buildings, natural obstacles, and weather conditions. The GPS receiver should only be used outdoors
to allow reception of GPS signals.
GPS should only be used as a navigation aid. It should not be used for precise location measurement and you should never rely
solely on location data from the GPS receiver for positioning or navigation.
The trip meter has limited accuracy, and rounding errors may occur. Accuracy can also be affected by availability and quality of
GPS signals.
The GPS applications in your device require an additional Bluetooth GPS enhancement to operate.
Positioning
Select Menu > Tools > Position..
To select a positioning method, scroll to the positioning method, and select Options > Enable. To stop using it, select Options >
Disable. The Bluetooth GPS positioning method enables you to use Bluetooth GPS enhancements for positioning. The Network
based positioning method is provided by your network operator or service provider. Both positioning methods can be used
simultaneously.
Navigator
Select Menu > Tools > Navigator.
Navigator is a GPS application that enables you to view your current location, find your way to a desired location, and track
distance. The coordinates to locations are expressed in degrees and decimal degrees using the WGS-84 coordinate system.
The application requires a Bluetooth GPS accessory to operate. You must also have Bluetooth GPS positioning method enabled
in Menu > Tools > Position..
The application must receive positioning info from at least three satellites to use it as a traveling aid.
The application requires a Bluetooth GPS accessory to operate.
Select from the following:
•
•
•
Navigation — View navigating information to your trip destination.
Position — View positioning information about your current location.
Trip distance — View your traveling information such as the distance and duration you have traveled and your average and
maximum speeds.
Navigation view
The navigation view guides you to your trip destination. The cardinal points are indicated by letters on the circle, and the general
direction to your destination by a deeper color.
Select Options, and from the following:
•
Set destination — Select a landmark or location as the destination of your trip, or enter the destination latitude and longitude
coordinates.
•
•
•
•
Stop navigation — Delete the destination set for your trip.
Save position — Save your current position as a location or landmark.
Satellite status — View the signal strength of the satellites that provide the positioning info necessary for navigation.
Saved locations — View the locations you have temporarily saved in your device to help in navigation.
Position view
View positioning info such as the latitude and longitude coordinates and altitude of your current location. You can also see the
accuracy of this info.
Select Options, and from the following:
•
•
•
Save position — Save your current position as a location or landmark.
Satellite status — View the signal strength of the satellites that provide the positioning info necessary for navigation.
Saved locations — View the locations you have temporarily saved in your device to help in navigation.
Trip distance view
The trip meter calculates the travelled distance and time and your average and maximum traveling speeds.
© 2007 Nokia. All rights reserved.
77
G P S a p p l i c a t i o n s
Select Options, and from the following:
•
•
•
•
•
•
•
•
Start — Activate the trip meter.
Stop — End using the trip meter. The values calculated by it remain on the display.
Resume — Continue using the trip meter.
Reset — Set the values calculated by the trip meter to zero and start recalculating them from the start.
Clear — Empty the trip meter values after stopping its use.
Save position — Save your current location as a location or landmark.
Satellite status — View the signal strength of the satellites that provide the positioning info necessary for navigation.
Saved locations — View the locations you have temporarily saved in your device to help in navigation.
Manage locations
Select Position > Options > Saved locations.
You can temporarily save locations in your device to help in navigation.
To save a location in Navigation, Position, or Trip distance view, select Options > Save position.
To save a temporary location as a more permanent landmark, select Options > Save as landmark.
To delete a location, scroll to it, and press Options > Clear.
Navigator settings
Select Options > Settings.
To change the measuring system in use, select Measurement system > Metric or Imperial.
To enter the altitude calibration to correct the altitude received from the positioning satellites, select Altitude calibration.
Landmarks
Select Menu > Tools > Landmarks.
Landmarks are coordinates to geographic locations that you can save to your device for later use in different location-based
services. The coordinates are expressed in degrees and decimal degrees using the WGS-84 coordinate system.
You can create landmarks using a Bluetooth GPS enhancement or network (network service). See "Navigator," p. 77.
To create a landmark, select Options > New landmark. Select Current position to make a network request for the latitude and
longitude coordinates of your current location or Enter manually to fill in the necessary location information such as a name,
category, address, latitude, longitude and altitude.
To view or edit a landmark, scroll to it, and press the scroll key.
To delete a landmark, scroll to it, and press the backspace key.
With each landmark, select Options and select from the following options:
•
Add to category — Organize the landmark to a group of similar landmarks. Scroll to the category, and press the scroll key. To
view your landmark categories, scroll right or left.
•
•
•
Send — Send the landmark to compatible devices.
Edit categories — Add, edit, or delete the your landmark categories.
Category icon — Change the icon of the landmark. Scroll to the desired icon, and press the scroll key.
Landmark categories
You can view landmark categories in two views: one lists categories that already contain landmarks, and the other lists all
categories that your device has.
To view categories that already contain landmarks, select Menu > Tools > Landmarks, and scroll right.
To view the landmarks that a category contains, select the category, and press the scroll key.
To move a landmark from one category to another, scroll left. Scroll to a landmark, and press Options > Add to category. Scroll
to the old category, and press the scroll key to remove the mark next to it. Scroll to the category or categories to which you
want to add the landmark, and press the scroll key. Select Accept.
With each landmark, select Options and select from the following options:
•
•
Edit — Modify landmark information such as a name, category, address, latitude, longitude and altitude.
New landmark — Create a landmark directly into the category. Select Current position to make a network request for the
latitude and longitude coordinates of your current location or Enter manually to fill in the necessary location information
such as a name, category, address, latitude, longitude and altitude.
•
•
•
Add to category — Organize the landmark to a group of similar landmarks. Scroll to the category, and press the scroll key.
Send — Send the landmark to compatible devices.
Edit categories — Add, edit, or delete the your landmark categories.
© 2007 Nokia. All rights reserved.
78
G P S a p p l i c a t i o n s
•
Category icon — Change the icon of the landmark. Scroll to the desired icon, and press the scroll key.
The available options may vary.
Edit landmark categories
Select Options > Edit categories.
Select Options and select from the following options:
•
New category — Create a landmark directly into the category. Select Current position to make a network request for the
latitude and longitude coordinates of your current location or Enter manually to fill in the necessary location information
such as a name, category, address, latitude, longitude and altitude.
•
Category icon — Change the icon of the landmark. Scroll to the desired icon, and press the scroll key.
To delete a landmark category that you have created, scroll to it and press the backspace key. You cannot delete preset categories.
Edit landmarks
Select Options > Edit or New landmark > Enter manually. Enter location and other information such as a name, category,
address, latitude, longitude and altitude.
With each landmark, select Options and select from the following options:
•
Select categories — Organize the landmark to a group of similar landmarks. Scroll to the category and press the scroll key to
modify landmark information such as a name, category, address, latitude, longitude and altitude.
Retrieve current posit. — Request and automatically fill in the geographical latitude and longitude coordinates to make a
landmark of your current location.
•
•
•
Category icon — Change the icon of the landmark. Scroll to the desired icon, and press the scroll key.
Send — Send the landmark to compatible devices.
Available options may vary.
Receive landmarks
Select Menu > Messag.. Open a message that contains a landmark you have received from another device. Scroll to the landmark,
and press the scroll key.
To save the landmark in your device, select Options > Save.
To forward the landmark to compatible devices, select Options > Send.
© 2007 Nokia. All rights reserved.
79
18.
Settings
Select Menu > Tools > Settings.
You can define and modify various settings of your device. Modifying these settings affects the operation of your device across
several applications.
Some settings may be preset for the device or sent to you in a configuration message by your network operator or service
provider. You may not be able to change such settings.
Scroll to the setting that you want to edit, and press the scroll key to do the following:
•
•
•
•
Switch between two values, such as on or off.
Select a value from a list.
Open a text editor to enter a value.
Open a slider to decrease or increase the value by scrolling left or right.
Phone settings
Select Phone to change the language settings, standby mode settings, and display settings of your device.
General settings
Select General and from the following:
•
•
•
•
Phone language — Select a language from the list. Changing the device language affects every application in your device.
When you change the language, the device restarts.
Writing language — Select a language from the list. Changing the writing language also affects the characters that are
available when writing text.
Welcome note / logo — Select Default to use the default image, Text to enter a welcome note of your own, or Image to select
an image from the Gallery. The welcome note or image is displayed briefly each time you switch on the device.
Orig. phone settings — Restore the original device settings. To do this, you need your device lock code. After resetting, the
device may take a longer time to power on. Documents, contact information, calendar entries, and files are unaffected.
Standby mode settings
Select Standby mode and from the following:
•
•
Active standby — Select On to have shortcuts to different applications available in the active standby mode.
Left selection key, Right selection key — Change the shortcuts that open from the left and right selection keys in the standby
screen. Press scroll key, select a function from the list, and OK.
•
Navigation key right, Navigation key left, Navigat. key down, Navigation key up, Selection key — Change the shortcuts that
open when you scroll to different directions. These settings are not available if you select Active standby > On.
Active standby apps. — Select the applications that you want to access from the active standby.
Active standby mailbox — Select the inbox or the mailbox that is shown in the active standby.
Active standby plug-ins — Select the plug-ins that are shown in the active standby. You can, for example, see how many voice
mails you have. Even if you switch off the active standby notifications for missed calls and messages, the default notification
will still show them. The available plug-ins may vary.
•
•
•
Display settings
Select Display and from the following:
•
•
Light sensor — Adjust the amount of light used to illuminate the device display.
Power saver time-out — Select the amount of time before the screen saver is activated. Activating the screen saver lengthens
the device operating time.
•
Light time-out — Set how quickly after last keypress the display dims.
Call settings
Select Call and from the following:
•
Send my caller ID — Select Yes to display your phone number to the person you are calling or Set by network to let the network
to determine whether your caller ID is sent.
•
•
Send my net call ID — Set this feature on if you want to display your net caller ID to the person you are calling.
Call waiting — Select Activate to be notified of a new incoming call while you have a call in progress or Check status to check
if the function is active on the network.
•
Internet call waiting — Activate this feature to be notified of a new incoming call while you have a net call in progress.
© 2007 Nokia. All rights reserved.
80
S e t t i n g s
•
•
•
•
•
•
Internet call alert — Set this on if you want the device to respond to the caller that it is busy. If you set this off, the device
emits a busy tone to the caller and you receive a notification about the missed call.
Default call type — Select Cellular to make normal calls to the phone number or Internet to use VoIP to call the number or
address.
Reject call with SMS — Select Yes to send a text message to the person who is calling you informing why you cannot answer
their incoming call.
Message text — Enter the text that is sent when you cannot answer an incoming call and want to automatically send a text
message as a reply.
Image in video call — Select Use selected to select a still image to be displayed instead of a video during a video call or
None to not send any image during a video call.
Automatic redial — Select On to redial a number if it was busy at the first call attempt. Your device makes a maximum of 10
attempts to connect the call.
•
•
Summary after call — Select On to briefly display the approximate duration of the last call.
Speed dialling — Select On to activate speed dialing on your device. To dial a phone number assigned to the speed dialing
keys (2-9), press and hold the key.
•
•
Anykey answer — Select On to answer an incoming call by briefly pressing any key, except the end key.
Line in use — Select Line 1 or Line 2 to change the phone line for outgoing calls and text messages (network service). This
setting is displayed only if the SIM card supports the alternate line service and a subscription to two phone lines.
Line change — Select Disable to prevent line selection (network service). To change this setting, you need the PIN2 code.
Internet call alert — Select Off to notify incoming net calls that your device is busy or On to accept incoming net calls.
•
•
Connection settings
Select Menu > Tools > Settings > Connection and from the following:
•
•
•
Access points — Set up new or edit existing access points. Some or all access points may be preset for your device by your
service provider, and you may not be able to create, edit, or remove them.
Access point groups — Set up new or edit existing access point groups that are used in automatic connection establishment
and e-mail roaming.
Packet data — Determine when packet data connections are used, and enter the access point if you use your device as a
modem for a computer.
•
•
•
•
Internet tel. settings — Define settings for net calls.
SIP settings — View or create session initiation protocol (SIP) profiles.
Data call — Set the time-out period after which data call connections automatically end.
VPN — Install and manage VPN policies, manage VPN policy servers, see the VPN log, and create and manage VPN access
points.
•
•
Wireless LAN — Determine if the device displays an indicator when a wireless LAN is available, and how often the device
searches for networks.
Configurations — View and delete trusted servers from which your device may receive configuration settings.
To obtain information about wireless LAN or subscribing to a packet data service and the appropriate connection and
configuration settings, contact your network operator or service provider.
The settings available for editing may vary.
Access points
Select Menu > Tools > Settings > Connection > Access points.
An access point is where your device connects to the network by way of a data connection. To use e-mail and multimedia services
or to browse web pages, you must first define access points for these services.
An access point group is used for grouping and prioritizing access points. An application can use a group as a connection method
instead of a single access point. In that case, the best available access point inside a group is used for making the connection,
and in case of e-mail, also for roaming.
Some or all access points may be preset for your device by your service provider, and you may not be able to create, edit, or
remove them.
Access point groups
Select Menu > Tools > Settings > Connection > Access point groups.
An access point group is used for grouping and prioritizing access points. An application can use a group as a connection method
instead of a single access point. In that case the best available access point inside a group is used for making connection and
in case of e-mail, also for roaming. See "Access point groups," p. 53.
© 2007 Nokia. All rights reserved.
81
S e t t i n g s
Packet data
Select Menu > Tools > Settings > Connection > Packet data.
Your device supports packet data connections, such as GPRS in the GSM network. When you are using your device in GSM and
UMTS networks, it is possible to have multiple data connections active at the same time; access points can share a data
connection, and data connections remain active (for example, during voice calls). See "Connection manager," p. 55.
Packet data settings
The packet data settings affect all access points using a packet data connection.
Select from the following:
•
Packet data conn. — Select When available to register the device to the packet data network when you switch the device on
in a supported network. Select When needed to establish a packet data connection only when an application or action requires
it.
•
Access point — Enter the access point name provided by your service provider to use the device as a packet data modem to
your computer.
These settings affect all access points for packet data connections.
Net call settings
Select Menu > Tools > Settings > Connection > Internet tel. settings. Select Options > New profile or Options > Edit.
Scroll to Name, press the scroll key, enter a name for the profile, and select OK.
Scroll to SIP profiles, press the scroll key, select a profile and OK. SIP protocols are used for creating, modifying, and terminating
communications sessions such as net calls with one or more participants. SIP profiles include settings for these sessions.
To save your settings, press Back.
Session initiation protocol (SIP) settings
Select Menu > Tools > Settings > Connection > SIP settings.
Session initiation protocols (SIP) are used for creating, modifying, and terminating certain types of communication sessions
with one or more participants (network service). SIP profiles include settings for these sessions. The SIP profile used by default
for a communication session is underlined.
To create a SIP profile, select Options > Add new > Use default profile or Use an existing profile.
To edit a SIP profile, scroll to it, and press the scroll key.
To select the SIP profile you want to use by default for communication sessions, scroll to the profile, and select Options >
Default profile.
To delete a SIP profile, scroll to it, and press the backspace key.
Edit SIP profiles
Select Menu > Tools > Settings > Connection > SIP settings > Options > Add new or Edit.
Select from the following:
•
•
•
•
•
•
•
•
•
Profile name — Enter a name for the SIP profile.
Service profile — Select IETF or Nokia 3GPP.
Default access point — Select the access point to use for the Internet connection.
Public user name — Enter your user name received from your service provider.
Use compression — Select if compression is used.
Registration — Select the registration mode.
Use security — Select if security negotiation is used.
Proxy server — Enter the proxy server settings for this SIP profile.
Registrar server — Enter the registration server settings for this SIP profile.
The settings available for editing may vary.
Edit SIP proxy servers
Select Menu > Tools > Settings > Connection > SIP settings > Options > Add new or Edit > Proxy server.
Proxy servers are intermediate servers between a browsing service and its users used by some service providers. These servers
may provide additional security and speed up access to the service.
Select from the following:
•
•
•
•
Proxy server address — Enter the host name or IP address of the proxy server in use.
Realm — Enter the proxy server realm.
User name and Password — Enter your user name and password for the proxy server.
Allow loose routing — Select if loose routing is allowed.
© 2007 Nokia. All rights reserved.
82
S e t t i n g s
•
•
Transport type — Select UDP or TCP.
Port — Enter the port number of the proxy server.
Edit registration servers
Select Menu > Tools > Settings > Connection > SIP settings > Options > Add new or Edit > Registrar server.
Select from the following:
•
•
•
•
•
Registrar serv. addr. — Enter the host name or IP address of the registrar server in use.
Realm — Enter the registrar server realm.
User name and Password — Enter your user name and password for the registrar server.
Transport type — Select UDP or TCP.
Port — Enter the port number of the registrar server.
Data call settings
Select Menu > Tools > Settings > Connection > Data call.
To set the time-out period after which data calls automatically end if no data has been transferred, select Online time, and press
the scroll key. Select User defined to enter the time yourself or Unlimited to keep the connection active until you select
Options > Disconnect.
VPN
VPN access points
To manage VPN access points, select VPN > VPN access points > Options, and from the following:
•
•
•
Edit — Edit the selected access point. If the access point is in use or its settings are protected, you cannot edit it.
New access point — Create a new VPN access point.
Delete — Delete the selected access point.
VPN access point settings
Contact your service provider for the correct access point settings.
To edit VPN access point settings, select the access point and Options.
Select from the following:
•
•
•
•
•
Connection name — Enter a name for the VPN connection. The maximum length of the name is 30 characters.
VPN policy — Select a VPN policy to be used with this access point.
Internet access pt. — Select the Internet access point to be used with this VPN access point.
Proxy serv. address — Enter the proxy server address of this VPN access point.
Proxy port number — Enter the number of the proxy port.
Wireless LAN
Select Menu > Tools > Settings > Connection > Wireless LAN.
To have an indicator displayed when there is a wireless LAN available in your current location, select Show availability > Yes.
To select the time interval for your device to scan for available wireless LANs and update the indicator, select Scan for
networks.
Advanced WLAN settings
Select Menu > Tools > Settings > Connection > Wireless LAN > Options > Advanced settings. The wireless LAN advanced
settings are normally defined automatically, and changing them is not recommended.
To edit the settings manually, select Automatic config. > Disabled, and define the following:
•
•
•
Long retry limit — Enter the maximum number of transmission attempts if the device does not receive a receiving
acknowledgement signal from the network.
Short retry limit — Enter the maximum number of transmission attempts if the device does not receive a clear-to-send signal
from the network.
RTS threshold — Select the data packet size at which the wireless LAN access point device issues a request to send before
sending the packet.
•
•
•
TX power level — Select the power level of your device when sending data.
Radio measurements — Enable or disable the radio measurements.
Power saving — Enable or disable conservation of battery power.
To restore all settings to their original values, select Options > Restore defaults.
© 2007 Nokia. All rights reserved.
83
S e t t i n g s
Security settings for wireless LAN access points
Select Menu > Tools > Settings > Connection > Access points. Select Options > New access point and start to create a wireless
LAN access point, or select a wireless LAN access point and Options > Edit.
WEP security settings
In the access point settings, select WLAN security mode > WEP.
Wired equivalent privacy (WEP) encryption method encrypts data before it is transmitted. Access to the network is denied to
users who do not have the required WEP keys. When WEP security mode is in use, if your device receives a data packet not
encrypted with the WEP keys, the data is discarded.
In an Ad-hoc network, all devices must use the same WEP key.
Select WLAN security sett. and from the following:
•
•
•
WEP key in use — Select the desired WEP key.
Authentication type — Select Open or Shared.
WEP key settings — Edit the settings for the WEP key.
WEP key settings
In the access point settings, select WLAN security mode > WEP.
In an Ad-hoc network, all devices must use the same WEP key.
Select WLAN security sett. > WEP key settings and from the following:
•
•
•
WEP encryption — Select the desired WEP encryption key length.
WEP key format — Select whether you want to enter the WEP key data in ASCII or Hexadecimal format.
WEP key — Enter the WEP key data.
802.1x security settings
In the access point settings, select WLAN security mode > 802.1x.
802.1x authenticates and authorizes devices to access a wireless network, and prevents access if the authorization process fails.
Select WLAN security sett.. and from the following:
•
•
WPA/WPA2 — Select EAP (Extensible Authentication Protocol) or Pre-shared key (a secret key used for device identification).
EAP plug-in settings — If you selected WPA/WPA2 > EAP, select which EAP plug-ins defined in your device to use with the
access point.
•
Pre-shared key — If you selected WPA/WPA2 > Pre-shared key, enter the shared private key that identifies your device to
the wireless LAN to which you connect.
The settings available for editing may vary.
WPA security settings
In the access point settings, select WLAN security mode > WPA/WPA2.
Select WLAN security sett.. and from the following:
•
•
WPA/WPA2 — Select EAP (Extensible Authentication Protocol) or Pre-shared key (a secret key used for device identification).
EAP plug-in settings — If you select WPA/WPA2 > EAP, select which EAP plug-ins defined in your device to use with the access
point.
•
Pre-shared key — If you select WPA/WPA2 > Pre-shared key, enter the shared private key that identifies your device to the
wireless LAN to which you connect.
The settings available for editing may vary.
EAP
To view the EAP (extensible authentication protocol) plug-ins currently installed in your device (network service), select Menu >
Tools > Settings > Connection > Access points. Select Options > New access point and define an access point that uses
wireless LAN as a data bearer and 802.1x or WPA/WPA2 as the security mode. Select WLAN security sett. > WPA/WPA2 > EAP,
scroll to EAP plug-in settings, and press the scroll key.
The extensible authentication protocol (EAP) plug-ins are used in wireless networks to authenticate wireless devices and
authentication servers, and the different EAP plug-ins make possible the use of various EAP methods (network service).
To use an EAP plug-in when you connect to a WLAN using the access point, select the desired plug-in and Options > Enable.
The EAP plug-ins enabled for use with this access point have a check mark next to them. To not use a plug-in, select Options >
Disable.
To edit the EAP plug-in settings, select Options > Configure.
To change the priority of the EAP plug-in settings, select Options > Raise priority to attempt to use the plug-in before other
plug-ins when connecting to the network with the access point, or Options > Lower priority to use this plug-in for network
authentication after attempting to use other plug-ins.
The available options may vary.
© 2007 Nokia. All rights reserved.
84
S e t t i n g s
Configurations
To view and delete configurations for trusted servers, select Menu > Tools > Settings > Connection > Configurations.
You can receive messages from your network operator, service provider, or company information management that contain
configuration settings for trusted servers. These settings are automatically saved in Configurations. You may receive
configuration settings for access points, multimedia or e-mail services, and IM or synchronization settings from trusted servers.
To delete configurations for a trusted server, scroll to the server, and press the backspace key. The configuration settings for
other applications provided by this server are also deleted.
Date and time settings
Security settings
Network settings
Select Menu > Tools > Settings > Network.
Define the following:
•
Network mode (shown only if supported by the network operator) — Select the network type. You can select GSM or UMTS
to use the respective network or Dual mode to have your device automatically switch between the two. This setting may be
preset for your device and not available for editing. If you set the device to use only the GSM network or only the UMTS network,
you will not be able to make any calls, including emergency calls, or use other features requiring a network connection, if
the selected network is unavailable.
•
•
Operator selection — Select Manual to choose from available networks, or Automatic to have the device select the network
automatically.
Cell info display — Select On to set the device to indicate when it is used in Micro Cellular Network (MCN).
Enhancement settings
Select Menu > Tools > Settings > Enhancement.
Warning: When you use the headset, your ability to hear outside sounds may be affected. Do not use the headset
where it can endanger your safety.
With most enhancements, you can select from the following settings:
•
•
Default profile — Select the profile that is activated when you attach an enhancement to your device.
Automatic answer — Let the device answer phone calls automatically when an enhancement is attached. Select On to have
the device answer an incoming call automatically after 5 seconds. If the ringing type is set to Beep once or Silent in the Profiles
menu, automatic answer is disabled.
•
Lights — Select On to illuminate the device while it is attached to an enhancement.
Text phone / TTY settings
If you use a text phone (TTY), you must connect it to your device before you can change the settings and use the text phone.
Select from the following settings:
•
•
Default profile — Select the profile that is activated when you attach a text phone (TTY, teletypewriter) to your device.
Use text phone — Select Yes if you want to start using the text phone.
© 2007 Nokia. All rights reserved.
85
19.
Security
Device security
Select Menu > Tools > Settings > Security > Phone and SIM.
You can modify the security settings for the PIN code, automatic lock, and SIM card change, and change codes and passwords.
Avoid using codes that are similar to emergency numbers to prevent accidental dialing of the emergency number.
Codes are shown as asterisks. When you change a code, enter the current code, then the new code twice.
Define security settings
To define device and SIM card settings, select a setting and Options > Change.
When calls are limited to closed user groups, calls may be possible to the official emergency number programmed into your
device.
Define the following settings:
•
PIN code request — Select On to request that the PIN code is entered each time the device is switched on. This setting cannot
be changed if the device is switched off. Some SIM cards do not allow turning off the PIN code request.
PIN code — Change the PIN code. The PIN code must be 4 to 8 numbers long. The PIN code protects your SIM card against
unauthorized use and is provided with the SIM card. After three consecutive incorrect PIN code entries, the PIN code is blocked,
and you need to use the PUK code to unblock it before you can use the SIM card again.
•
•
•
PIN2 code — Change the PIN2 code. The PIN2 code must be 4 to 8 numbers long. The PIN2 code is required to access some
functions of the device and is provided with the SIM card. After three consecutive incorrect PIN2 code entries, the PIN2 code
is blocked, and you need to use the PUK2 code to unblock it before you can use the SIM card again.
Autolock period — Set a time-out after which the device is automatically locked and can be used only if the correct lock code
is entered. Enter a number for the time-out in minutes, or select None to turn off the autolock period. When the device is
locked, you can still answer incoming calls and calls may still be possible to the official emergency number programmed into
your device.
•
Lock code — Change the lock code. The new code can be 4-255 characters long. Both alphabets and digits can be used, and
both uppercase and lowercase alphabets are possible. The device notifies you if the lock code is not properly formatted. The
preset code is 12345. To avoid unauthorized use of your device, change the lock code. Keep the new code secret and in a safe
place separate from your device.
•
•
Lock if SIM changed — Set the device to ask for the lock code when an unknown, new SIM card is inserted into your device.
The device maintains a list of SIM cards that are recognized as the owner’s cards.
Allow remote lock — If you set this option on, you can lock the device by sending a predefined text message from another
phone. When you set this option on, you need to enter the remote lock message and confirm the message. The message
must be at least 5 characters long.
•
•
Closed user group (network service) — Specify a group of people to whom you can call and who can call you.
Confirm SIM services (network service) — Set the device to display confirmation messages when you are using a SIM card
service.
Change the barring password
To change the password used for barring voice, fax, and data calls, select Menu > Tools > Settings > Call barring > Cellular
call barring > Options > Edit barrings passw.. Enter the current code, then the new code twice. The barring password must be
four digits long. For details, contact your service provider.
Fixed dialing
When fixed dialing is activated, calls may be possible to the official emergency number programmed into your device.
Press the contacts key. Select Options > SIM contacts > Fixed dialling contacts.
With the fixed dialing service, you can restrict calls from your device to only certain phone numbers. Not all SIM cards support
the fixed dialing service. Contact your service provider for more information.
Select Options, and select from the following options:
•
•
•
Activ. fixed dialling — Restrict calls from your device. To cancel the service, select Deact. fixed dialling. You need your PIN2
code to activate and deactivate fixed dialing or edit your fixed dialing contacts. Contact your service provider if you do not
have the code.
New SIM contact — Add a phone number to the list of numbers to which calls are allowed. Enter the contact name and phone
number. To restrict calls by a country prefix, enter the country prefix in New SIM contact. All phone numbers to which calls
are allowed must start with this country prefix.
Add from Contacts — Copy a contact from Contacts to your fixed dialing list.
© 2007 Nokia. All rights reserved.
86
S e c u r i t y
Tip: To send text messages to the SIM contacts while the fixed dialing service is active, you need to add the text message
center number to the fixed dialing list.
To view or edit a phone number to which calls from your device are allowed, select Options > SIM contacts > Fixed dialling
contacts.
To call the contact, press the call key.
To edit the phone number, select Options > Edit. You may need your PIN2 code to edit your fixed dialing numbers.
To delete the contact, press the backspace key.
Memory card security
You can protect a memory card with a password to prevent unauthorized access. To set a password, select Options > Set
password. The password can be up to 8 characters long and is case-sensitive. The password is stored in your device and you do
not need to enter it again while you use the memory card on the same device. If you use the memory card on another device,
you are asked for the password. Not all memory cards support password protection.
To remove the memory card password, select Options > Remove password. When you remove the password, the data on the
memory card is not protected against unauthorized use.
Certificate manager
Important: Even if the use of certificates makes the risks involved in remote connections and software installation
considerably smaller, they must be used correctly in order to benefit from increased security. The existence of a
certificate does not offer any protection by itself; the certificate manager must contain correct, authentic, or trusted
certificates for increased security to be available. Certificates have a restricted lifetime. If "Expired certificate" or
"Certificate not valid yet" is shown even if the certificate should be valid, check that the current date and time in your
device are correct.
Before changing any certificate settings, you must make sure that you really trust the owner of the certificate and that
the certificate really belongs to the listed owner.
Digital certificates are used to verify the origins of software but do not guarantee safety. There are three different types of
certificates: authority certificates, personal certificates, and server certificates. During a secure connection, a server may send a
server certificate to your device. Upon receipt, it is checked through an authority certificate stored on your device. You receive
notification if the identity of the server is not authentic or if you do not have the correct certificate in your device.
Download a certificate from a web site, or receive a certificate as an e-mail attachment, or as a message sent through a Bluetooth
or infrared connection. Certificates should be used when you connect to an online bank or a remote server to transfer confidential
information. They should also be used if you want to reduce the risk of viruses or other malicious software, and to check the
authenticity of software when you download and install software to your device.
Tip: When you add a new certificate, check its authenticity.
Manage personal certificates
Personal certificates are certificates that are issued to you.
To add certificates to your device, select a certificate file and Save. To remove a selected certificate, select Options > Delete.
To check the authenticity of a certificate, scroll to a certificate and press the scroll key to open Certificate details. Fingerprints
uniquely identify a certificate. Contact the help desk or customer service of the owner of the certificate, and ask to compare
fingerprints. Six-digit private key store passwords contain the secret keys that come with personal certificates.
Manage authority certificates
Authority certificates are used by some services to check the validity of other certificates.
To add certificates to your device, select a certificate file and Save. To remove a selected certificate, select Options > Delete.
To check the authenticity of a certificate, scroll to a certificate and press the scroll key to open Certificate details. Fingerprints
uniquely identify a certificate. Contact the help desk or customer service of the owner of the certificate, and ask to compare
fingerprints. Six-digit private key store passwords contain the secret keys that come with personal certificates.
Trusting a certificate means that you authorize it to verify web pages, e-mail servers, software packages, and other data. Only
trusted certificates can be used to verify services and software.
To change trust settings, select a certificate and Options > Trust settings. Select an application field and Yes or No. You cannot
change the trust settings of a personal certificate.
Depending on the certificate, a list of applications is displayed that can use the certificate:
•
Symbian installation — New Symbian operating system application.
© 2007 Nokia. All rights reserved.
87
S e c u r i t y
•
•
•
Internet — E-mail and graphics.
App. installation — New Java™ application.
Online certif. check — Online certificate status protocol.
View certificate details
You can only be sure of the correct identity of a server when the signature and the period of validity of a server certificate have
been checked.
To view certificate details, scroll to a certificate and press the scroll key.
One of the following notes may appear:
•
•
•
•
Certificate not trusted — You have not set any application to use the certificate. You may want to change the trust settings.
Expired certificate — The period of validity has ended for the selected certificate.
Certificate not valid yet — The period of validity has not yet begun for the selected certificate.
Certificate corrupted — The certificate cannot be used. Contact the certificate issuer.
Certificate security settings
Select from the following:
•
•
•
Software installation — Select to install signed applications only or all applications.
Online certif. check — To check the validity of certificates when an application is installed, select On.
Default web address — The validity of a certificate is checked from the default address if the certificate does not include its
own Web address.
Mobile VPN
Select Menu > Tools > Settings > Connection > VPN.
The Nokia mobile virtual private network (VPN) client creates a secure connection to compatible corporate Intranet and services,
such as e-mail. Your device connects from a mobile network, through the Internet, to a corporate VPN gateway that acts as a
front door to the compatible corporate network. VPN client uses IP Security (IPSec) technology. IPSec is a framework of open
standards for supporting secure exchange of data over IP networks.
VPN policies define the method used by VPN client and a VPN gateway to authenticate each other, and the encryption algorithms
that they use to help protect the confidentiality of data. Contact your corporation for a VPN policy.
To use VPN with an application, the application must be associated with a VPN access point. A VPN access point is made up of
an Internet access point and a VPN policy.
VPN management
You can manage your VPN policies, policy servers, VPN logs, and key store password in VPN management. VPN policies define
how data is encrypted for transfer over unsecured networks. The key store password helps protect private keys.
An access point is where your device connects to the network by way of a data call or packet data connection. To use e-mail
and multimedia services or to browse Web pages, you must first define Internet access points for these services. VPN access
points pair VPN policies with Internet access points to create encrypted connections.
To manage VPN, select VPN management > Options > Open and from the following options:
•
•
•
VPN policies — Install, view, and update VPN policies.
VPN policy servers — Edit the connection settings of VPN policy servers from which you can install and update VPN policies.
VPN log — View the log for your VPN policy installations, updates and synchronizations, and other VPN connections.
Manage VPN policies
To manage VPN policies, select VPN management > VPN policies > Options and from the following options:
•
Install policy — Install a policy. Enter your user name and password for the VPN policy server. Contact your system
administrator for your user name and passwords.
•
•
•
Define VPN ac. point — Create a VPN access point that pairs a VPN policy with an Internet access point.
Update policy — Update the selected VPN policy.
Delete policy — Delete the selected VPN policy. If you delete a VPN policy, it is reinstalled when you synchronize your device
with the VPN policy server the next time unless it has also been deleted from the server. Similarly, if a VPN policy has been
deleted from the server, it is deleted also from your device upon synchronization.
To manage VPN policy servers, select VPN policy servers > Options > Open and from the following options:
•
•
•
New server — Add a VPN policy server.
Synchronise server — Install new or update the selected VPN policy.
Delete server — Delete the selected VPN policy server.
© 2007 Nokia. All rights reserved.
88
S e c u r i t y
To manage VPN policy server settings, select Options > New server or Edit server and from the following options:
•
•
Policy server name — Enter a new name for the server, up to 30 characters.
Policy server addr. — Enter the server address. The policy server address cannot be edited after you connect to the server to
install or update VPN policies.
•
•
Internet access pt. — Select the Internet access point to connect to the VPN policy server.
Key store password — Change the password of the private key store. The password is created automatically when it is needed
for the first time.
View the VPN log
Select VPN management > VPN log.
A VPN log records your visits to VPN servers to install, update, and synchronize VPN policies and your VPN connections. Error,
warning, and information entries are indicated by an icon on the left-hand side of the entry. To view a log entry in detail, select
it. Report the reason codes visible in the detailed view to your system administrators as the codes help to look for causes of
possible problems you may have with VPN. When the log size reaches 20 KB, the oldest log entries are deleted to make space
for new entries.
Select Options and from the following options:
•
•
Refresh log — Update the log.
Clear log — Delete the log entries.
Activation keys
Select Menu > Tools > Actv. keys.
You can view and manage permission rights on your protected media files using alphanumerical keys. These keys specify rights
that determine when you can play, display, execute, or print media files. Rights for media files can also restrict the number of
times the media can be rendered (played, displayed, executed, or printed) or the period of time you are allowed to render the
object before your rights to the media expire.
Select either Valid keys, Invalid keys, or Not in use. Scroll to the desired file, and select Options > Key details.
The following details are displayed for each media file:
•
•
Status — The status is either Activation key is valid, Activation key expired, or Activation key not yet valid.
Content sending — Allowed means that you can send the file to another device. Not allowed means that you cannot send
the file to another device.
•
Content in phone — Yes ([14]) means that the file is in the device and the path of the file is displayed. No means that the
related file is not currently in the device.
Activate content
From the main view of the activation keys, select Invalid keys > Options > Get activation key. Establish a network connection
at the prompt, and you are directed to a Web site where you can purchase rights to the media.
Delete file rights
In the Valid keys or Not in use tabs, scroll to the desired file. Select Options > Delete. If there are several rights related to the
same media file, all the rights are deleted.
Work with groups
The group key view displays all of the files related to a group right. If you have downloaded multiple media files with the same
rights, they are all displayed in this view. You can open the group view from either the Valid keys or Invalid keys tabs. To access
these files, open the group rights folder.
To rename a group, select Options > Rename. Enter the new name to change the name of the group rights.
Security settings for wireless LAN access points
© 2007 Nokia. All rights reserved.
89
20.
Shortcuts
Here are some of the available keyboard shortcuts in your device. Shortcuts can make the use of the applications more efficient.
Some shortcuts are application-specific and they are not available for all applications.
General shortcuts
Power key
Menu key
Switch between profiles. Press and hold to switch your device on and off.
Open the main menu screen for access to all applications. Press and hold
to switch between open applications.
End key
Close applications. Press and hold to end data connections (GPRS, data
call).
E-mail key
Open your default e-mail box. Press and hold to begin composing a new
e-mail.
Active standby mode
Left selection key + blue function key
Lock and unlock the keypad.
#
Press and hold to switch between the general and silent profiles.
Open the Log.
Call key
0
1
Press and hold to open Services and connect to the Web.
Press and hold to call your voice mailbox.
Number key (2–9)
Call a phone number using speed dialing. You must first activate speed
dialing (Menu > Tools > Settings > Call > Speed dialling > On).
Blue function key + Chr
Blue function key + Ctrl
Activate infrared.
Activate and deactivate Bluetooth.
In applications
Shift + scroll key
Select text. Press and hold the shift key and scroll left or right to select
text.
Ctrl+C
Ctrl+X
Ctrl+V
Ctrl+I
Ctrl+B
Copy.
Cut.
Paste.
Italics.
Bold.
Press the blue function key once (so that you see ) Enter a number or a character marked in blue on a key.
+ the other key.
Press the blue function key twice (so that you see
) + the other key.
Shift key
Enter only numbers or characters marked in blue on a key.
Switch between character cases.
While browsing the web
#
*
Zoom out.
Zoom in.
1
2
3
5
8
Return to bookmarks.
Search for text strings on the open website.
Return to the previous page.
Switch between your open browser windows.
Zoom out to show the whole web page and outline in red what is
viewable on the display.
© 2007 Nokia. All rights reserved.
90
S h o r t c u t s
9
Go to a different web page.
Image viewer
Call key
Send the image.
0
5
7
4
6
2
8
3
1
*
Zoom out.
Zoom in.
Zoom in. Press twice for the full screen size.
Scroll left in the zoomed image.
Scroll right in the zoomed image.
Scroll up in the zoomed image.
Scroll down in the zoomed image.
Rotate clockwise.
Rotate counterclockwise.
Switch between the full screen size and normal view.
Music player
5
4
Pause a track.
Return to the beginning of the track. Press within two seconds after a
song has started to go to the previous track. Press and hold to rewind.
6
8
Go to the next track. Press and hold to fast forward.
Stop a track.
© 2007 Nokia. All rights reserved.
91
Battery information
Your device is powered by a rechargeable battery. The battery can be charged and discharged hundreds of times, but it will
eventually wear out. When the talk and standby times are noticeably shorter than normal, replace the battery. Use only Nokia
approved batteries, and recharge your battery only with Nokia approved chargers designated for this device.
If a replacement battery is being used for the first time or if the battery has not been used for a prolonged period, it may be
necessary to connect the charger, then disconnect and reconnect it to begin charging the battery.
Unplug the charger from the electrical plug and the device when not in use. Do not leave a fully charged battery connected to
a charger, since overcharging may shorten its lifetime. If left unused, a fully charged battery will lose its charge over time.
If the battery is completely discharged, it may take several minutes before the charging indicator appears on the display or
before any calls can be made.
Use the battery only for its intended purpose. Never use any charger or battery that is damaged.
Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object such as a coin, clip, or pen causes
direct connection of the positive (+) and negative (-) terminals of the battery. (These look like metal strips on the battery.) This
might happen, for example, when you carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage
the battery or the connecting object.
Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and
lifetime of the battery. Always try to keep the battery between 15°C and 25°C (59°F and 77°F). A device with a hot or cold battery
may not work temporarily, even when the battery is fully charged. Battery performance is particularly limited in temperatures
well below freezing.
Do not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged. Dispose of batteries according
to local regulations. Please recycle when possible. Do not dispose as household waste.
Do not dismantle or shred cells or batteries. In the event of a battery leak, do not allow the liquid to come in contact with the
skin or eyes. In the event of such a leak, flush your skin or eyes immediately with water, or seek medical help.
© 2007 Nokia. All rights reserved.
92
Nokia battery authentication guidelines
Always use original Nokia batteries for your safety. To check that you are getting an original Nokia battery, purchase it from an
authorised Nokia dealer, and inspect the hologram label using the following steps:
Successful completion of the steps is not a total assurance of the authenticity of the battery. If you have any reason to believe
that your battery is not an authentic, original Nokia battery, you should refrain from using
it.
verified,
If authenticity cannot be
return the battery to the place of purchase.
Authenticate hologram
1. When you look at the hologram on the label, you should see the Nokia connecting hands symbol from one
angle and the Nokia Original Enhancements logo when looking from another angle.
2. When you angle the hologram left, right, down and up, you should see 1, 2, 3 and 4 dots on each side
respectively.
What if your battery is not authentic?
If you cannot confirm that your Nokia battery with the hologram on the label is an authentic Nokia battery, please do not use
the battery.The use of a battery that is not approved by the manufacturer may be dangerous and may result in poor performance
It may also invalidate any approval or warranty applying to the device.
and damage to your device and its enhancements.
To find out more about original Nokia batteries, visit
© 2007 Nokia. All rights reserved.
93
Care and maintenance
Your device is a product of superior design and craftsmanship and should be treated with care. The following suggestions will
help you protect your warranty coverage.
•
Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode
electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing
it.
•
•
Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged.
Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp
or melt certain plastics.
•
Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device
and damage electronic circuit boards.
•
•
•
•
•
•
Do not attempt to open the device other than as instructed in this guide.
Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
Do not paint the device. Paint can clog the moving parts and prevent proper operation.
Use a soft, clean, dry cloth to clean any lenses, such as camera, proximity sensor, and light sensor lenses.
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could
damage the device and may violate regulations governing radio devices.
•
•
•
Use chargers indoors.
Always create a backup of data you want to keep, such as contacts and calendar notes.
To reset the device from time to time for optimum performance, power off the device and remove the battery.
These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working properly,
take it to the nearest authorized service facility for service.
Disposal
The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the European Union all
electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their
working life. Do not dispose of these products as unsorted municipal waste.
Return the products to collection to prevent possible harm to the environment or human health from uncontrolled waste
disposal and to promote the sustainable reuse of material resources. Collection information is available from the product retailer,
local waste authorities, national producer responsibility organizations, or your local Nokia representative. For more information,
© 2007 Nokia. All rights reserved.
94
Additional safety information
Small children
Your device and its enhancements may contain small parts. Keep them out of the reach of small children.
Operating environment
This device meets RF exposure guidelines when used either in the normal use position against the ear or when positioned at
least 2,2 centimeters (7/8 inches) away from the body. When a carry case, belt clip, or holder is used for body-worn operation,
it should not contain metal and should position the device the above-stated distance from your body.
To transmit data files or messages, this device requires a quality connection to the network. In some cases, transmission of data
files or messages may be delayed until such a connection is available. Ensure the above separation distance instructions are
followed until the transmission is completed.
Parts of the device are magnetic. Metallic materials may be attracted to the device. Do not place credit cards or other magnetic
storage media near the device, because information stored on them may be erased.
Medical devices
Operation of any radio transmitting equipment, including wireless phones, may interfere with the functionality of inadequately
protected medical devices. Consult a physician or the manufacturer of the medical device to determine if they are adequately
shielded from external RF energy or if you have any questions. Switch off your device in health care facilities when any regulations
posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive
to external RF energy.
Implanted medical devices
Manufacturers of medical devices recommend that a minimum separation of 15.3 centimeters (6 inches) should be maintained
between a wireless device and an implanted medical device, such as a pacemaker or implanted cardioverter defibrillator, to
avoid potential interference with the medical device. Persons who have such devices should:
•
Always keep the wireless device more than 15.3 centimeters (6 inches) from the medical device when the wireless device is
turned on.
•
•
•
•
Not carry the wireless device in a breast pocket.
Hold the wireless device to the ear opposite the medical device to minimize the potential for interference.
Turn the wireless device off immediately if there is any reason to suspect that interference is taking place.
Read and follow the directions from the manufacturer of their implanted medical device.
If you have any questions about using your wireless device with an implanted medical device, consult your health care provider.
Hearing aids
Some digital wireless devices may interfere with some hearing aids. If interference occurs, consult your service provider.
Vehicles
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel
injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems, and air bag systems. For more
information, check with the manufacturer, or its representative, of your vehicle or any equipment that has been added.
Only qualifiedpersonnelshouldservice the device orinstallthe device inavehicle. Faulty installationorservice may be dangerous
and may invalidate any warranty that may apply to the device. Check regularly that all wireless device equipment in your vehicle
is mounted and operating properly. Do not store or carry flammable liquids, gases, or explosive materials in the same
compartment as the device, its parts, or enhancements. For vehicles equipped with an air bag, remember that air bags inflate
with great force. Do not place objects, including installed or portable wireless equipment in the area over the air bag or in the
air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could
result.
Using your device while flying in aircraft is prohibited. Switch off your device before boarding an aircraft. The use of wireless
teledevices in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless telephone network, and may
be illegal.
Potentially explosive environments
Switch off your device when in any area with a potentially explosive atmosphere, and obey all signs and instructions. Potentially
explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas
could cause an explosion or fire resulting in bodily injury or even death. Switch off the device at refueling points such as near
© 2007 Nokia. All rights reserved.
95
A d d i t i o n a l s a f e t y i n f o r m a t i o n
gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel depots, storage, and distribution areas;
chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not
always, clearly marked. They include below deck on boats, chemical transfer or storage facilities, vehicles using liquefied
petroleum gas (such as propane or butane), and areas where the air contains chemicals or particles such as grain, dust, or metal
powders.
Emergency calls
Important: Wireless phones, including this device, operate using radio signals, wireless networks, landline networks,
and user-programmed functions. Because of this, connections in all conditions cannot be guaranteed. You should never
rely solely on any wireless device for essential communications like medical emergencies.
To make an emergency call:
1. If the device is not on, switch it on. Check for adequate signal strength.
Some networks may require that a valid SIM card is properly inserted in the device.
2. Press the end key as many times as needed to clear the display and ready the device for calls.
3. Enter the official emergency number for your present location. Emergency numbers vary by location.
4. Press the call key.
If certain features are in use, you may first need to turn those features off before you can make an emergency call. If the device
is in the offline or flight profile mode, you may need to change the profile to activate the phone function before you can make
an emergency call. Consult this guide or your service provider for more information.
When making an emergency call, give all the necessary information as accurately as possible. Your wireless device may be the
only means of communication at the scene of an accident. Do not end the call until given permission to do so.
CERTIFICATION INFORMATION (SAR)
THIS MOBILE DEVICE MEETS GUIDELINES FOR EXPOSURE TO RADIO WAVES.
Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves
recommended by international guidelines. These guidelines were developed by the independent scientific organization ICNIRP
and include safety margins designed to assure the protection of all persons, regardless of age and health.
The exposure guidelines for mobile devices employ a unit of measurement known as the Specific Absorption Rate or SAR. The
SAR limit stated in the ICNIRP guidelines is 2.0 watts/kilogram (W/kg) averaged over 10 grams of tissue. Tests for SAR are
conducted using standard operating positions with the device transmitting at its highest certified power level in all tested
frequency bands. The actual SAR level of an operating device can be below the maximum value because the device is designed
to use only the power required to reach the network. That amount changes depending on a number of factors such as how
close you are to a network base station. The highest SAR value under the ICNIRP guidelines for use of the device at the ear is
0.90 W/kg.
Use of device accessories and enhancements may result in different SAR values. SAR values may vary depending on national
reporting and testing requirements and the network band. Additional SAR information may be provided under product
© 2007 Nokia. All rights reserved.
96
Index
connectors 10
A
applications
contacts
adding 43
installing 65
groups 43
removing 65
D
data
connections 49
synchronizing 66
display
B
battery
indicators 14
settings 80
charging
installing
documents 61
blogs 59
Bluetooth
E
connections 50
pairing 51
e-mail
accounts 33
settings 50
messages 22
bookmarks 58
replying 24
writing 24
equalizer 75
C
cable 49
calculator 63
calendar 46
F
calling 35
feeds 59
calls
Find 20
barring 36
diverting 36
settings 80
certificates 87
G
gallery 72
GPRS 49
counters 42
settings 82
charging the battery
chat 28
clock 48
H
connection methods
Bluetooth 50
help 15
I
IM 28
cable 49
images
infrared 52
indicators 14
infrared 52
modem 52
connections
© 2007 Nokia. All rights reserved.
97
I n d e x
installing
notes 62
applications 65
battery
O
SIM card
Own key
Internet 58
configuring 11
settings 53
P
counters 42
J
settings 82
pairing 51
K
passwords
keys 10
phone
L
landmarks 78
language 80
locking
calls 35
language 80
device 12
settings 80
keys 12
photos 70
playing
M
mail
music 74
See e-mail
presentations 62
printing 62
memory 17
card 17
monitoring 17
on-device 17
passwords 87
unlocking 18
menu 16
profiles 19
Q
Quickoffice 61
Quickpoint 62
Quicksheet 62
Quickword 61
messages
deleting 24
e-mail 22
R
folders 22
mobile VPN
RealPlayer
settings 74
recording
calls 75
See VPN
voice 75
modem 52
multimedia messages
attachments 28
creating 26
remote configuration
settings 66
receiving 27
sending 26
settings 32
S
Search 20
N
navigation 77
security
device 86
© 2007 Nokia. All rights reserved.
98
I n d e x
settings
TTY 85
tutorial 15
Bluetooth 50
U
calendar 46
calls 80
connection 81
display 80
V
general 80
VoIP 40
Internet 53
network 85
profiles 19
security 86
standby 80
trust 87
VPN 88
W
TTY 85
Web 58
Web 59
settings 59
WLAN 83
Welcome 16
SIM card
wireless LAN
infrastructure 56
WLAN
installing
software
settings 83
installing 65
removing 65
Speech 18
Z
spreadsheets 62
standby
mode 13
settings 80
storage 17
switch on and off
synchronizing 66
T
text
copying 17
pasting 17
selecting 16
writing 16
text messages
replying 25
sending 25
writing 25
themes 20
© 2007 Nokia. All rights reserved.
99
|