Nokia E70 User Manual

Nokia E70 User Guide  
9242115  
Issue 3  
Contents  
C o n t e n t s  
C o n t e n t s  
For your safety  
Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information.  
SWITCH ON SAFELY  
Do not switch the device on when wireless phone use is prohibited or when it may cause interference or danger.  
ROAD SAFETY COMES FIRST  
Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should  
be road safety.  
INTERFERENCE  
All wireless devices may be susceptible to interference, which could affect performance.  
SWITCH OFF IN HOSPITALS  
Follow any restrictions. Switch the device off near medical equipment.  
SWITCH OFF IN AIRCRAFT  
Follow any restrictions. Wireless devices can cause interference in aircraft.  
SWITCH OFF WHEN REFUELLING  
Do not use the device at a refueling point. Do not use near fuel or chemicals.  
SWITCH OFF NEAR BLASTING  
Follow any restrictions. Do not use the device where blasting is in progress.  
USE SENSIBLY  
Use only in the normal position as explained in the product documentation. Do not touch the antennas unnecessarily.  
QUALIFIED SERVICE  
Only qualified personnel may install or repair this product.  
ENHANCEMENTS AND BATTERIES  
Use only approved enhancements and batteries. Do not connect incompatible products.  
WATER-RESISTANCE  
Your device is not water-resistant. Keep it dry.  
BACK-UP COPIES  
Remember to make back-up copies or keep a written record of all important information.  
CONNECTING TO OTHER DEVICES  
When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products.  
EMERGENCY CALLS  
Ensure the phone function of the device is switched on and in service. Press the end key as many times as needed to clear the display  
and return to the standby mode. Enter the emergency number, then press the call key. Give your location. Do not end the call until  
given permission to do so.  
About your device  
The wireless device described in this guide is approved for use on the EGSM900/1800/1900, UMTS 2100 networks. Contact your service  
provider for more information about networks.  
When using the features in this device, obey all laws, and respect privacy and legitimate rights of others.  
Warning: To use any features in this device, other than the alarm clock, the device must be switched on. Do not switch the device on  
when wireless device use may cause interference or danger.  
NETWORK SERVICES  
To use the phone you must have service from a wireless service provider. Many of the features in this device depend on features in the wireless  
network to function. These network services may not be available on all networks or you may have to make specific arrangements with your  
service provider before you can utilize network services. Your service provider may need to give you additional instructions for their use and  
explain what charges will apply. Some networks may have limitations that affect how you can use network services. For instance, some networks  
may not support all language-dependent characters and services.  
Copyright © 2006 Nokia. All Rights Reserved.  
6
     
F o r y o u r s a f e t y  
Your service provider may have requested that certain features be disabled or not activated in your device. If so, they will not appear on your  
device menu. Your device may also have been specially configured. This configuration may include changes in menu names, menu order and  
icons. Contact your service provider for more information.  
This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols. Some features of this device, such as MMS, browsing, e-  
mail, and content downloading using the browser or over MMS, require network support for these technologies.  
Enhancements, batteries, and chargers  
Check the model number of any charger before use with this device. This device is intended for use when supplied with power from the LCH-12,  
ACP-12, and AC-1 chargers.  
Warning: Use only batteries, chargers, and enhancements approved by Nokia for use with this particular model. The use of any other  
types may invalidate any approval or warranty, and may be dangerous.  
For availability of approved enhancements, please check with your dealer. When you disconnect the power cord of any enhancement, grasp  
and pull the plug, not the cord.  
Your device and its enhancements may contain small parts. Keep them out of reach of small children.  
Copyright © 2006 Nokia. All Rights Reserved.  
7
 
1.  
Get started  
Note: Your service provider may have requested that certain features be disabled or not activated in your device. If  
so, they do not appear on your device menu. Your device may also have been specially configured for your network  
provider. This configuration may include changes in menu names, menu order and icons. Contact your service provider  
for more information.  
Model number: Nokia E70-1  
Hereinafter referred to as Nokia E70.  
Insert the SIM card and battery  
Keep all SIM cards out of the reach of small children. For availability and information on using SIM card services, contact your  
SIM card vendor. This may be the service provider, network operator, or other vendor.  
1. Always switch the device off, and disconnect the charger before removing the battery.  
With the back of the device facing you, press the cover release button (1), and slide the back cover in the direction of the  
arrow (2).  
2. If the battery is installed, lift the battery from the battery compartment in the direction of the arrow to remove it .  
3. To release the SIM card holder, slide it in the direction of the arrow (1), and lift it (2). Insert the SIM card into the SIM card  
slot (3).  
Ensure that the beveled corner of the SIM card is pointing up and the contact area on the card is facing the device. Lower the  
SIM card holder (4), and slide it until it locks into place (5).  
4. To insert the battery, align the contacts of the battery with the corresponding connectors on the battery compartment, insert  
in the direction of the arrow, and gently click the battery into place.  
Copyright © 2006 Nokia. All Rights Reserved.  
8
     
G e t s t a r t e d  
5. Insert the locking catches of the back cover into the corresponding slots (1), and slide the cover in the direction of the arrow  
(2).  
Instead of a SIM card, you may also have a USIM card, which is an enhanced version of the SIM card and is supported by UMTS  
(network service) mobile phones. Contact your service provider for more information and settings.  
Insert a memory card  
If you have a memory card, follow the instructions to insert it.  
1. Remove the battery cover.  
2. Insert the memory card fully into the memory card slot. Ensure that the beveled corner of the memory card is pointing  
towards the device and the contact area is facing down.  
3. Replace the battery cover.  
4. To remove the memory card, press the power key and select Remove mem. card. Remove the battery cover and push the  
memory card into the device to activate the release mechanism. Then, gently pull the card out of your device.  
Important: Do not remove the memory card in the middle of an operation when the card is being accessed.  
Removing the card in the middle of an operation may damage the memory card as well as the device, and data  
stored on the card may be corrupted.  
Charge the battery  
1. Connect the charger to a wall outlet.  
2. Connect the power cord to the bottom of the device. The battery indicator bar starts scrolling on the display. If the battery  
is completely discharged, it may take a few minutes before the charging indicator is shown. The device can be used while  
charging.  
3. When the battery is fully charged, the bar stops scrolling. Disconnect the charger from the device, then from the outlet.  
When the battery charge level is too low for operation, the device switches itself off.  
Switch on your device  
1. To switch the device on, press the power key.  
2. If the device asks for a PIN code (or UPIN code, if you have a USIM card), lock code or security code, enter the code, and select  
OK.  
3. To switch the device off, press the power key.  
Copyright © 2006 Nokia. All Rights Reserved.  
9
         
G e t s t a r t e d  
Tip: When you switch the device on, it may recognize the SIM card provider and configure the correct text message,  
multimedia message, and GPRS settings automatically. If not, contact your service provider for the correct settings, or  
use the Sett. wizard application.  
The device can be used without the network dependant phone functions when a SIM card is not inserted or when the Offline  
profile is selected.  
The picture shows the location of the power key.  
Enter basic settings  
When you power on the device for the first time, and when you power on the device after the battery has been empty or removed  
for a longer period of time, your device asks for the city in which you are located, time, and date. You can change the settings  
later.  
1. Select the city in which you are located from the list and OK. To browse for a city, start to type the name of the city, or scroll  
to a city. It is important to select the correct city, because scheduled calendar entries that you create can change if the new  
city is located on a different time zone.  
2. Set the time, and select OK.  
3. Set the date, and select OK.  
You can use your device with the fold closed or open.  
1. To open the fold, lift the keypad into the direction of the arrow (1). When you open the fold, you can use the full-size keyboard  
(2).  
2.  
The device changes the orientation of the display to portrait or landscape, depending on whether you use the device with  
the fold open or closed.  
Keys and parts  
Fold open  
Copyright © 2006 Nokia. All Rights Reserved.  
10  
         
G e t s t a r t e d  
1 — Keypad light key. Press the key to illuminate your keypad for a period of time.  
2 — Power key  
3 — Selection keys  
4 — Internet key. Press and hold the key in the standby mode to browse the Web.  
5 — Clear (backspace) key  
6 — Chr key. Press the Chr key to open a character table where you can select special characters.  
7 — Menu key. Press the Menu key to access the applications installed in your device. With a long keypress, you can see a list of  
the active applications and switch between them. In this User Guide, "select Menu" refers to pressing this key.  
8 — Shift key. Press Shift+character key to produce uppercase letters.  
9 — Space bar  
10 — Call key  
11 — Light sensor and earpiece  
12 — Joystick. Press the joystick to enter a selection. Use the joystick to scroll left, right, up, down, or to move around on the  
screen.  
13 — End key  
Press the end key to reject a call, end active calls and held calls, close applications, and with a long keypress, end data connections  
(GPRS, data call).  
14 — Space bar  
15 — Shift key. Press shift and character key to produce uppercase letters.  
16 — Ctrl key  
17 — Enter key  
Tip: Press the clear (backspace) key to delete items such as calendar entries and messages. Press the clear (backspace)  
key to delete characters on the left side of the cursor, or shift+clear (backspace) key to delete characters on the right  
side of the cursor.  
The display changes from portrait to landscape when you open the fold. The application that was active the last time the device  
was used is shown on the display. When you close the fold, the display changes from landscape to portrait.  
Fold closed  
1 — Power key  
2 — Loudspeaker  
3 — Infrared port  
4 — Left selection key, joystick, and right selection key. Press either selection key to perform the function shown above it on  
the display. Press the joystick to enter a selection or access most commonly used functions in different applications. Use the  
joystick to scroll left, right, up, down, or to move around on the screen. During a call, scroll left or right with the joystick to  
change volume.  
5 — End key  
6 — Clear key  
7 — Menu key. Press the Menu key to access the menu. In this User Guide, "select Menu" refers to pressing this key.  
8 — Internet key. Press and hold the key in the standby mode to browse the Web.  
Copyright © 2006 Nokia. All Rights Reserved.  
11  
   
G e t s t a r t e d  
9 — Microphone. Do not cover the microphone with your hand during phone calls.  
10 — Pop-Port™ connector for the USB data cable, headset, and loopset  
11 — Charger connector  
12 — Edit key  
13 — Call key  
14 — Voice key/push to talk (PTT) key.  
15 — Display  
16 — Earpiece  
17 — Light sensor  
Keypad lock (keyguard)  
When the keypad lock is on, calls may be possible to the official emergency number programmed into your device.  
Use the keypad lock (keyguard) to prevent the keys on the device from being accidentally pressed.  
To lock the keypad in the standby mode, press the left selection key and *. To unlock, press the left selection  
key and * again.  
Tip: To lock the keypad in the Menu or in an open application, press the power key briefly, and  
select Lock keypad. To unlock, press the left selection key and *.  
You can also lock the device in the standby mode using your lock code. Press the power key, select Lock  
phone, and enter your lock code. Your lock code can contain both numbers and alphabets, but the number  
mode is on by default. The default lock code is 12345. To unlock, press the left selection key, enter your lock  
code, and press the joystick.  
Connectors  
Warning: When you use the headset, your ability to hear outside sounds may be affected. Do not use the headset  
where it can endanger your safety.  
Battery charger connector  
Pop-Port connector for headset and  
other enhancements  
Antennas  
Your device has two internal antennas.  
Note: As with any other radio transmitting device, do not touch either of the antennas unnecessarily when the device  
is switched on. Contact with the antenna affects call quality and may cause the device to operate at a higher power  
level than otherwise needed. Not touching the antenna area during a phone call optimises the antenna performance  
and the talktime of your device.  
Copyright © 2006 Nokia. All Rights Reserved.  
12  
           
G e t s t a r t e d  
The picture shows the normal use of the device at the ear for voice calls.  
About the display  
A small number of missing, discolored, or bright dots may appear on the screen. This is a characteristic of this type of display.  
Some displays may contain pixels or dots that remain on or off. This is normal, not a fault.  
Standby modes  
Your device has two different standby modes: active standby mode and standby mode.  
Active standby mode  
After you have switched on your device and it is ready for use, but you have not entered any characters or made other selections,  
the device is in the active standby mode. In the active standby mode, you can view your service provider and network, different  
indicators such as indicators for alarms, and applications you want to access fast.  
To select applications that you want to access from active standby, select Standby apps. Scroll to the different shortcut settings,  
and press the joystick. Scroll to the desired application, and press the joystick.  
To use the basic standby mode, select Menu > Tools > Settings > Phone > Standby mode > Active standby > Off.  
You can see the messages in a messaging folder such as inbox or mailbox in the active standby mode. Select Menu > Tools >  
Settings > Phone > Standby mode and the folders in Active standby mailbox.  
Tip: You can also see different notifications, such as missed calls, unread messages, or voice mails in the active standby  
mode. With these notifications, you can see the communication status of your device with one glance. Select the plug-  
ins in Menu > Tools > Settings > Phone > Standby mode > Active standby plug-ins. The available plug-ins may vary.  
Standby mode  
In the standby mode, you can see different information, such as your service provider, time, and different indicators, such as  
indicators for alarms.  
The picture shows a the display in the standby mode.  
1 — Service provider  
2 — Signal strength indicator  
3 — Command for left selection key  
4 — Command for right selection key  
5 — Battery strength indicator  
Shortcuts in standby mode  
In the standby mode, you can use the following shortcuts. These shortcuts are usually not available in the active standby mode,  
where the joystick is used for normal scrolling.  
Copyright © 2006 Nokia. All Rights Reserved.  
13  
             
G e t s t a r t e d  
To view the most recently dialed numbers, press the call key. Scroll to a number or name, and press the call key again to call the  
number.  
To call your voice mailbox (network service), press and hold 1.  
To view calendar information, scroll right.  
To write and send text messages, scroll left.  
To open the contacts list, press the joystick.  
To change the profile, press the power key briefly, scroll to the profile you want, and press the joystick to activate the profile.  
To open Services and connect to the Web, press 0.  
To activate the camera, scroll up with the joystick.  
To change these shortcuts, select Menu > Tools > Settings > Phone > Standby mode.  
Display indicators  
The device is being used in a GSM network. The bar next to the icon indicates the signal strength of the network at your  
current location. The higher the bar, the stronger the signal.  
The device is being used in a UMTS network (network service). The bar next to the icon indicates the signal strength of the  
network at your current location. The higher the bar, the stronger the signal.  
The battery charge level. The higher the bar, the stronger the charge in the battery.  
You have one or more unread messages in the Inbox folder in Messag..  
You have received new e-mail in the remote mailbox.  
You have one or more missed phone calls.  
An alarm is active.  
You have selected the silent profile, and the device does not ring for an incoming call or message.  
Bluetooth is activated.  
An infrared connection is active. If the indicator blinks, your device is trying to connect to the other device, or the connection  
has been lost.  
A GPRS or EGPRS packet data connection is available.  
A GPRS or EGPRS packet data connection is active.  
A GPRS or EGPRS packet data connection is on hold.  
A UMTS packet data connection is available.  
A UMTS packet data connection is active.  
A UMTS packet data connection is on hold.  
You have set the device to scan for wireless LANs, and a wireless LAN is available.  
A wireless LAN connection is active in a network that does not have encryption.  
A wireless LAN connection is active in a network that has encryption.  
Your device is connected to a PC with a USB data cable.  
A data call is active.  
IP passthrough is active.  
and  
Indicate the phone line that you have selected, if you have subscribed to two phone lines (network service).  
All calls are forwarded to another number.  
A headset is connected to the device.  
The connection to a headset with Bluetooth connectivity has been lost.  
A hands-free car kit is connected to the device.  
A loopset is connected to the device.  
A Text phone is connected to the device.  
Your device is synchronizing.  
You have an ongoing push to talk connection.  
Copyright © 2006 Nokia. All Rights Reserved.  
14  
   
G e t s t a r t e d  
Volume control  
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely  
loud.  
To adjust the volume during a call, scroll left or right.  
To adjust the volume when using the loudspeaker, scroll left or right.  
Write text  
Traditional text input  
is shown on the top right of the display when you are writing text using traditional text input.  
and  
indicate the selected case.  
indicates that the first letter of the sentence is written in uppercase and all the  
indicates number mode.  
other letters will automatically be written in lowercase.  
Press a number key 1–9 repeatedly until the desired character appears. There are more characters available for a number key  
than are printed on the key.  
To insert a number, press and hold the number key.  
To switch between letter and number mode, press and hold #.  
If the next letter is located on the same key as the present one, wait until the cursor appears, and enter the letter.  
To erase a character, press the clear key. Press and hold the clear key to clear more than one character.  
To access the most common punctuation marks, press the 1 key. Press 1 repeatedly to reach the desired punctuation mark.  
Press * to open a list of special characters. Use the joystick to move through the list, and select a character.  
If you are writing with the full keyboard and want to add accented characters by using other keys such as "A" or "O", press  
and hold the Chr key and simultaneously press the other key as many times as is needed before the character you want is  
shown.  
To insert a space, press 0. To move the cursor to the next line, press 0 three times.  
To switch between the different character cases, press #.  
Predictive text input  
1. To activate predictive text input, press the edit key, and select Predictive text on. This activates predictive text input for all  
editors in the device. The indicator  
text input.  
is shown on the top right of the display when you are writing text using predictive  
2. To write the desired word, press 2–9. Press each key only once for one letter.  
3. When you have finished writing the word and it is correct, to confirm it, scroll right, or press 0 to add a space.  
If the word is not correct, press * repeatedly to view the matching words the dictionary has found one by one.  
If the ? character is shown after the word, the word you intended to write is not in the dictionary. To add a word to the  
dictionary, select Spell, enter the word (up to 32 letters) using traditional text input, and select OK. The word is added to the  
dictionary. When the dictionary is full, a new word replaces the oldest added word.  
4. Start writing the next word.  
Tip: To set predictive text input on or off, press # twice quickly.  
Write the first half of a compound word; to confirm it, scroll right. Write the last part of the compound word. To complete the  
compound word, press 0 to add a space.  
To turn predictive text input off for all editors in the device, press the edit key, and select Predictive text > Off.  
Copy text to the clipboard  
1. To select letters and words, press and hold the edit key. At the same time, scroll in the direction necessary to highlight the  
word, phrase, or line of text you want to copy. As the selection moves, the text is highlighted.  
2. To copy the text to the clipboard, while still holding the edit key, select Copy. To insert the text into a document, press and  
hold the edit key, and select Paste.  
Change writing language  
If you are writing text, for example a note or a message, you can change the writing language. When you are writing and press  
a key several times to reach a specific character, changing the writing language gives you access to a different characters.  
For example, if you are writing text using a non-Latin alphabet and want to write Latin characters for Web addresses, select  
Options > Writing language and the writing language to have access to a language that uses Latin characters.  
Copyright © 2006 Nokia. All Rights Reserved.  
15  
                     
G e t s t a r t e d  
If you are writing with the fold open, press Shift+Chr to change the language.  
Memory  
There are two types of memory into which you can save data or install applications: device memory and removable memory.  
Removable memory  
Removable memory is data storage that is not built into your device, such as a SIM card or a memory card. A SIM card stores  
different information, such as information about the network operator and contacts. A memory card serves as external storage  
media for software applications, pictures, music, contacts, text, or any other form of electronic data. High-capacity memory  
cards are available.  
Device memory  
Memory that is built into your device is a dynamic memory pool shared by many applications. The amount of internal memory  
available varies but cannot be increased past the maximum factory setting. Data stored on the device, such as software  
applications, pictures, and music, consume on-device memory.  
Monitor device memory  
Select Menu > Options > Memory details.  
You can see how much memory is currently in use, how much free memory remains, and how much memory is consumed by  
each data type. For example, you can see how much memory your e-mail messages, text documents, or calendar appointments  
consume.  
To switch between device memory and memory card statistics, select Memory details > Phone mem. or Memory details > Memory  
card.  
Tip: To ensure that you have adequate memory, you should regularly delete or transfer data to a memory card or PC.  
Memory card  
Use only compatible miniSD cards with this device. Other memory cards, such as MultiMediaCards, reduced-size MultiMediaCards  
or full-size SD cards, do not fit in the memory card slot and are not compatible with this device. Using an incompatible memory  
card may damage the memory card as well as the device, and data stored on the incompatible card may be corrupted.  
Your Nokia device only supports the FAT16 and FAT32 file systems for memory cards. If you use a memory card from another  
device or if you want to ensure compatibility of the memory card with your Nokia device, you may need to format the memory  
card with your Nokia device. However, all data in the memory card is permanently deleted if you format the memory card.  
It is recommended to back up device memory regularly to the memory card. The information can be restored to your device  
later. To back up information from device memory to a memory card, select Menu > Tools > Memory card > Options > Backup  
phone mem. To restore information from the memory card to the device memory, select Menu > Tools > Memory card >  
Options > Restore from card.  
To remove the memory card, press the power key and select Remove mem. card.  
Do not remove the memory card when the card is being accessed. Removing the card in the middle of an operation may damage  
the memory card as well as the device, and data stored on the card may be corrupted.  
If you cannot use a memory card in your device, you may have the wrong type of memory card, the card may not be formatted  
for your device, or the card has a corrupted file system.  
Tip: You can install and remove a memory card without removing the battery or powering off the device.  
MiniSD  
This device uses a mini Secure Digital (SD) card.  
Check the compatibility of a miniSD with its manufacturer or provider. Use only compatible miniSD cards with this  
device. Other memory cards, such as MultiMediaCards (MMC) or full-size SD cards, do not fit in the miniSD card slot and  
are not compatible with this device. Using an incompatible memory card may damage the memory card as well as the device,  
and data stored on the incompatible card may be corrupted. Keep all memory cards out of the reach of small children.  
Use a memory card  
Select Menu > Tools > Memory card > Options, and from the following:  
Remove mem. card Eject the memory card safely.  
Backup phone mem. Back up important information, such as your calendar entries or contacts, to your memory card.  
Restore from card Restore the backup from the memory card to your device.  
Copyright © 2006 Nokia. All Rights Reserved.  
16  
                     
G e t s t a r t e d  
Format mem. card Format a memory card for your device.  
Memory card name Change the name of the memory card.  
Set password Create a password for the memory card.  
Memory details Monitor the memory consumption of applications and data.  
Format a memory card  
When a memory card is formatted, all data on the card is lost permanently. Consult your retailer to find out if you must format  
the memory card before you can use it. To format a memory card, select Options > Format mem. card. When formatting is  
complete, enter a name for the memory card.  
Memory card security  
You can protect a memory card with a password to prevent unauthorized access. To set a password, select Options > Set  
password. The password can be up to eight characters long and is case-sensitive. The password is stored in your device. You do  
not need to enter it again while you use the memory card on the same device. If you use the memory card on another device,  
you are asked for the password. Not all memory cards support password protection.  
To remove the memory card password, select Options > Remove password. When you remove the password, the data on the  
memory card is not protected against unauthorized use.  
Unlock a memory card  
To open a locked memory card, select Options > Unlock memory card. Enter the password.  
CD-ROM  
The sales package CD-ROM is compatible with Windows 98SE, Windows ME, Windows 2000, and Windows XP.  
You can install Nokia PC Suite from the CD-ROM. Nokia PC Suite can be used only with Windows 2000 and Windows XP.  
Nokia support and contact information  
downloads, and services related to your Nokia product.  
On the Web site, you can get information on the use of Nokia products and services. If you need to contact customer service,  
For maintenance services, check your nearest Nokia service center at www.nokia.com/repair.  
Transfer content between devices  
You can transfer content, such as contacts, from a compatible Nokia device to your Nokia E70 using Bluetooth connectivity or  
infrared. The type of content that can be transferred depends on the phone model. If the other device supports synchronization,  
you can also synchronize data between the other device and your Nokia E70.  
Transfer data from another device  
Tip: If you transfer data from your previous phone, the phone may require you to insert the SIM card. Your Nokia E70  
does not need a SIM card when transferring data.  
To start transferring data from a compatible device, select Menu > Tools > Transfer.  
1. In the information view, select Continue.  
2. Select Via Bluetooth. Both devices must support the selected connection type.  
3. Activate Bluetooth in your other device, and select Continue in your Nokia E70 to start searching for devices with active  
Bluetooth connectivity.  
4. Select Stop in your Nokia E70 after it has found your other device.  
5. Select your other device from the list. You are asked to enter a passcode (1 to 16 digits) on your Nokia E70. The passcode is  
used only once to confirm this connection.  
6. Enter the code on your Nokia E70, and select OK. Enter the passcode on your other device, and select OK. The devices are now  
For some phone models, the Transfer data application is sent to your other device as a message. To install Transfer data on  
your other device, open the message, and follow the instructions on the display.  
7. From your Nokia E70, select the content you want to transfer from your other device, and OK.  
Infrared connectivity  
1. In the information view, select Continue.  
2. Select Via infrared. Both devices must support the selected connection type.  
Copyright © 2006 Nokia. All Rights Reserved.  
17  
                 
G e t s t a r t e d  
3. Connect the two devices. See "Infrared," p. 48.  
4. From your Nokia E70, select the content you want to transfer from your other device, and OK.  
Content is copied from the memory of the other device to the corresponding location in your device. Copying time depends on  
the amount of data to be transferred. You can also cancel and continue later.  
The necessary steps for data transfer may vary depending on your device, and whether you have interrupted data transfer  
earlier. The items that you can transfer vary depending on the other device.  
Synchronize data with another device  
If you have previously transferred data to your Nokia E70, and your other device supports synchronization, you can use  
Transfer to keep the data of the two devices up to date.  
1. Select Phones, and press the joystick.  
2. Scroll to the device from which you transferred data, and press the joystick.  
3. Select Synchronise, and press the joystick. The devices start synchronizing using the same connection type that you selected  
when you originally transferred data. Only the data that you originally selected for data transfer is synchronized.  
To modify the data transfer and synchronization settings, select Synchronise, scroll to a device, press the joystick, and select  
Edit.  
Copyright © 2006 Nokia. All Rights Reserved.  
18  
 
2.  
Your device  
When you switch the device on, it may recognize the SIM card provider and configure the correct text message, multimedia  
message, and GPRSsettings automatically. You mayalso receive the settings as a specialtext message from your service provider.  
Menu  
The Menu is a starting point from which you can open all applications in the device or on a memory card. The Menu contains  
applications and folders, which are groups of similar applications. Use the joystick to scroll up and down on the screen.  
Applications that you install are saved in the Installat. folder by default.  
To open an application, scroll to it, and press the joystick.  
To view the applications in a list, select Options > Change view > List. To return back to the grid view, select Options > Change  
view > Grid.  
To view the memory consumption of different applications and data stored on the device or memory card and to check the  
amount of free memory, select Options > Memory details and the memory.  
To rearrange the folder, scroll to the application you want to move, and select Options > Move. A check mark is placed beside  
the application. Scroll to a new location, and select OK.  
To move an application to a different folder, scroll to the application you want to move to another folder, and select Options >  
Move to folder, the new folder, and OK.  
To download applications from the Web, select Options > App. downloads.  
To create a new folder, select Options > New folder. You cannot create folders inside folders.  
To rename a new folder, select Options > Rename.  
Tip: To switch between several open applications, press and hold the menu key. The application-switching window  
opens and displays the open applications. Scroll to an application, and press the joystick to switch to it.  
Help and tutorial  
You can find answers to your questions while using the device even with no user guide present, because your device includes  
both a task-specific help and a tutorial.  
Tip: Task-specific means you can access instructions from Options lists.  
Device help  
You can access the device help from an open application or from the Menu. When you have an application open, select  
Options > Help to read instructions for the current view.  
To open help from Menu, select Help > Help. In Help, you can select categories for which you want to see instructions. Scroll to  
a category, such as Messaging, and press the joystick to see what instructions (help topics) are available. While you are reading  
the topic, scroll left or right to see the other topics in that category.  
When you are reading the instructions, press and hold the menu key to switch between help and the application that is open  
in the background.  
Tutorial  
The tutorial provides you information about your device and shows you how to use it.  
To access the tutorial in the menu, select Menu > Help, open Tutorial and the section you want to view.  
Scroll and make selections  
Use the joystick to move and make selections. With the joystick, you can move up, down, left and right in the Menu or in different  
applications or lists. You can also press the joystick to open applications, files, or edit settings.  
To select text, press and hold the edit key, and scroll left or right until you have selected the text.  
To select different items, such as messages, files, or contacts, scroll up, down, left or right to highlight the item you want to  
select. Select Options > Mark/Unmark > Mark to select one item or Options > Mark/Unmark > Mark all to select all items.  
Tip: To select almost all items, first select Options > Mark/Unmark > Mark all, then select the items you do not want,  
and Options > Mark/Unmark > Unmark.  
Copyright © 2006 Nokia. All Rights Reserved.  
19  
                 
Y o u r d e v i c e  
To select an object (for example, an attachment in a document) scroll to the object so that square markers appear on each side  
of the object.  
Common actions in several applications  
You can find the following actions in several applications:  
To switch between open applications, press and hold the menu key to see a list of open applications. Select an application.  
To change the profile or switch off or lock the device, press the power key briefly.  
To save a file, select Options > Save. There are different save options depending on the application you use.  
To send a file, select Options > Send. You can send a file in an e-mail or multimedia message, or using infrared or Bluetooth.  
To print to a compatible printer, select Options > Print. You can preview items that you want to print, or edit the way printed  
pages look. Before you can print, you must define a compatible printer to your device. See "Print," p. 70.  
To copy, press the edit key, and select the text with the joystick. Press and hold the edit key, and select Copy. To paste, scroll to  
where you want to paste the text, press and hold the edit key, and select Paste. This method may not work in applications such  
as Documents that have their own copy and paste commands.  
To delete a file, press the clear key, or select Options > Delete.  
To insert characters such as question marks or parentheses to text, press *.  
Copyright © 2006 Nokia. All Rights Reserved.  
20  
   
3.  
Make calls  
When the device is locked, calls still may be possible to the official emergency number programmed into your device.  
In the offline profile, you may need to enter the lock code and change the device to a calling profile before making any call,  
including a call to an emergency number.  
To make and receive calls, the device must be switched on, the device must have a valid SIM card installed, and you must be  
located in a service area of the cellular network. The GPRS connection is put on hold during voice calls unless the network  
supports dual transfer mode or you have a USIM card and are within the coverage of a UMTS network.  
Enter the phone number, including the area code, and press the call key. If you enter an incorrect character, press the clear key.  
Tip: For international calls, press the * key twice to add the + character that replaces the international access code,  
and enter the country code, area code (omit the leading 0, if necessary), and phone number.  
To end the call or cancel the call attempt, press the end key.  
To make a call using the saved contacts, press Contacts in standby mode. Enter the first letters of the name, scroll to the name,  
and press the call key. See "Contacts," p. 28.  
Press the call key to view up to 20 numbers that you last called or attempted to call. Scroll to the desired number or name, and  
press the call key to dial the number.See "Log," p. 23.  
To adjust the volume of an active call, scroll left or right with the joystick.  
When you open the fold of the device during a call, the loudspeaker is activated.  
To call your voice mailbox (network service) in standby mode, press and hold 1, or press 1 then the call key.  
Speed dial  
Speed dialing allows you to make a call by pressing and holding a number key.  
Before using speed dialing, select Menu > Tools > Settings > Call > Speed dialling > On.  
To assign a number key to a phone number, select Menu > Tools > Speed dial. Scroll to the number key (2 - 9) on the screen,  
and select Options > Assign. Select the desired number from the Contacts directory.  
To remove the phone number assigned to a number key, scroll to the speed dialing key, and select Options > Remove.  
To change a phone number assigned to a number key, scroll to the speed dialing key, and select Options > Change.  
Answer a call  
Note: The actual invoice for calls and services from your service provider may vary, depending on network features,  
rounding off for billing, taxes, and so forth.  
To answer a call, press the call key.  
To reject the call, press the end key.  
To mute a ringing tone instead of answering a call, select Silence.  
To answer a new call during a call when the Call waiting function is activated, press the call key. The first call is put on hold. To  
end the active call, press the end key.  
Options during a call  
Select Options for the following options during a call:  
Mute Listen to the active conversation, but your voice cannot be heard by the other parties of the call.  
Unmute Your voice can be heard again by the other parties of the call.  
Drop Drop a party from the active call.  
End active call End the currently active call.  
Menu View the applications menu of your device.  
Hold — Place the active call on hold.  
Unhold Remove the active call from hold.  
New call — Place a new call while on a call, if conference calling (network service) is available.  
Answer Answer an incoming call while on a call, if Call waiting is activated.  
Reject Reject an incoming call while on a call, if Call waiting is activated.  
Lock keypad Lock the device keypad while on a call.  
Conference Merge an active and a held call into a conference call (network service).  
Private Converse privately with a selected participant during a conference call (network service).  
Swap Alternate between an active and a held call (network service).  
Copyright © 2006 Nokia. All Rights Reserved.  
21  
               
M a k e c a l l s  
Send DTMF — Send DTMF (dual tone multi-frequency) tone strings, for example, passwords. Enter the DTMF string or search  
for it in Contacts, and select DTMF.  
Transfer Connect the held call to the active call and disconnect yourself from the call (network service).  
The available options may vary.  
Divert calls  
Select Menu > Tools > Settings > Call divert.  
Divert incoming calls to your voice mailbox or to another phone number. For details, contact your service provider.  
1. Select a call type from the following:  
Voice calls — Incoming voice calls.  
Data and video calls — Incoming data and video calls.  
Fax calls — Incoming fax calls.  
2. Select one of the following call diverting options:  
All voice calls, All data and vid. calls, or All fax calls. — Divert all incoming voice, data and video, or fax calls.  
If busy Divert incoming calls when you have an active call.  
If not answered Divert incoming calls after your device rings for a specified period of time. Define the time you let the  
device ring before diverting the call in the Delay time: field.  
If out of reach Divert calls when the device is switched off or out of network coverage.  
If not available Activate the last three settings at the same time. This option diverts calls if your device is busy, not  
answered, or out of reach.  
3. Select Activate.  
To check the current diverting status, scroll to the diverting option, and select Options > Check status.  
To stop diverting voice calls, scroll to the diverting option, and select Options > Cancel.  
Call barring  
Call barring and call diverting cannot be active at the same time.  
When calls are barred, calls still may be possible to certain official emergency numbers.  
Select Menu > Tools > Settings > Call barring.  
You can bar the calls that can be made or received with the device (network service). To change the settings, you need the  
barring password from your service provider. Call barring affects all calls, including data calls.  
To bar calls, select Cellular call barring and select from the following options:  
Outgoing calls — Prevent making voice calls with your device.  
Incoming calls Bar incoming calls.  
International calls — Prevent calling to foreign countries or regions.  
Incoming if abroad Bar incoming calls when outside your home country.  
Intern. except home — Prevent calls to foreign countries or regions, but to allow calls to your home country.  
To check the status of voice call barrings, scroll to the barring option, and select Options > Check status.  
To stop all voice call barrings, scroll to a barring option, and select Options > Cancel all barrings.  
Net call barring  
To bar net calls, select Menu > Tools > Settings > Call barring > Internet call barring.  
To reject net calls from anonymous callers, select Anonymous calls > On.  
Send DTMF tones  
You can send dual tone multi-frequency (DTMF) tones during an active call to control your voice mailbox or other automated  
phone services.  
To send a DTMF tone sequence, make a call, and wait until the other end answers. Select Menu > Options > Send DTMF. Type the  
DTMF tone sequence, or select a predefined sequence.  
To attach DTMF tone sequences to contact cards, select Menu > Contacts. Open a contact, and select Options > Edit > Options >  
Add detail > DTMF. Enter the tone sequence. Press * three times to insert p, a pause of about 2 seconds before or between DTMF  
tones. Select Done. To set the device to send the DTMF tones only after you select Send DTMF during a call, press * four times to  
insert w.  
Copyright © 2006 Nokia. All Rights Reserved.  
22  
             
M a k e c a l l s  
Video calls  
To be able to make a video call, you need to be in the coverage of a UMTS network. For availability of and subscription to video  
call services, contact your network operator or service provider. While talking, you can see a real-time, two-way video between  
you and the recipient of the call, if the recipient has a compatible mobile phone. The video image captured by the camera in  
your device is shown to the video call recipient. A video call can only be made between two parties.  
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely  
loud.  
To make a video call, enter the phone number or select the recipient of the call from Contacts, and select Options > Call > Video  
call. When the video call starts, the camera of your device is activated. If the camera is already in use, video sending is disabled.  
If the recipient of the call does not want to send a video back to you, a still image is shown instead. You can define the still  
image in Tools > Settings > Call settings > Image in video call. You cannot convert the video call to a normal voice call.  
During the call, select Options and from the following:  
Disable — Select to disable Sending audio, Sending video or Sending audio & video.  
Activate loudsp. — Select to use the loudspeaker for receiving audio.  
Activate handset Mute the loudspeaker and use the handset.  
End active call End the active call.  
Open active standby Open the active standby view.  
Change image order — Swap the places of images.  
Zoom in or Zoom out Zoom the image on the display.  
Log  
Select Menu > Log.  
In the Log, you can view information about the communication history of the device.  
To view the logs for recent voice calls, their approximate duration, and packed data connections, select Recent calls, Call  
duration, or Packet data; and press the joystick.  
To sort the events by type or direction, scroll right to open the general log, and select Options > Filter. Scroll to a filter type, and  
press the joystick. Select the type or direction, and press the joystick.  
To set the time how long all communication events are held in the log, select Options > Settings > Log duration, an option, and  
OK.  
To clear missed and received calls and dialed numbers, select Recent calls > Options > Clear recent calls.  
To reply to a caller with a message, select Recent calls > Missed calls > Options > Create message. You can send text messages  
and multimedia messages.  
To add the caller or the sender of a message to Contacts, select the caller or sender of a message, and select Recent calls > Missed  
calls > Options > Add to Contacts.  
To view the amount of data sent or received using GPRS, select Packet data.  
To clear the GPRS counters, select Options > Clear counters. Enter your lock code, and select OK.  
Log settings  
To set the time for keeping all communication events in the Log, select Options > Settings > Log duration, an option from the  
list, and OK.  
To see the call duration during the call, select Options > Settings > Show call duration > Yes.  
Push to talk  
Select Menu > Connect. > PTT.  
Push to talk (PTT) (network service) provides direct voice communication connected with the push of a key. With push to talk,  
you can use your device as you would use a walkie-talkie.  
You can use push to talk to have a conversation with one person or with a group of people, or to join a channel. A channel is  
like a chat room: you can call the channel to see if anyone is online. The channel call does not alert the other participants; the  
participants just join the channel and start speaking with each other.  
In push to talkcommunication, one person talks while the other participants listen through the built-in loudspeaker. Participants  
take turns responding to each other. Because only one participant can talk at a time, the maximum duration of a speech turn  
is limited. For details of the speech turn duration for your network, contact your network operator or service provider.  
Remember to hold the device in front of you during a push to talk call so you can see the display. Speak towards the microphone,  
and do not cover the loudspeaker with your hands.  
Copyright © 2006 Nokia. All Rights Reserved.  
23  
             
M a k e c a l l s  
Phone calls always take priority over push to talk.  
Before you can use push to talk, you must define the push to talk access point and push to talk settings. You may receive the  
settings in a special text message from the service provider that offers the push to talk service.  
User settings  
Select Options > Settings > User settings.  
Define the following:  
Incoming PTT calls — Select Notify if you want to see a notification of incoming calls. Select Auto-accept if you want push to  
talk calls to be answered automatically. Select Not allowed if you want push to talk calls to be rejected automatically.  
PTT call alert tone — Select Set by profile if you want the incoming call alert setting for push to talk to follow your profile  
settings. If your profile is silent, you are not available to others using push to talk, except for callback requests.  
Callback request tone Define the ringing tone for callback requests.  
Application start-up — Select if you want to log in to the push to talk service when you switch on your device.  
Default nickname Enter your default nickname (20 characters maximum) that is displayed to other users.  
Show my PTT address Define if you want callers to see your push to talk address. You can let all callers see the address,  
show the address only to one-to-one callers or channel participants, or hide the address from all callers.  
Show my login status Define whether your login to the push to talk server is shown or hidden from other users.  
Connection settings  
Select Options > Settings > Connection settings.  
Define the following:  
Domain Enter the domain name obtained from your service provider.  
Access point name — Select the push to talk access point.  
Server address Enter the IP address or domain name of the push to talk server obtained from your service provider.  
User name Enter your user name obtained from your service provider.  
Password Enter a password, ifrequired, to log into the push to talkservice. The password is provided bythe service provider.  
Log in to push to talk service  
If you have set Application start-up on in User settings, push to talk automatically logs in to the service when started. If not, you  
must log in manually.  
To log in to a push to talk service, select Options > Settings > Connection settings, and enter your User name, Password,  
Domain, Server address, and Access point name. Select Options > Switch PTT on.  
When the Ringing type setting of your device is set to Beep once or Silent, or there is an ongoing phone call, you cannot make  
or receive push to talk calls.  
Push to talk calls  
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely  
loud.  
Select Options > PTT contacts.  
To make a push to talk call, select one or several contacts from the list, and press the voice key. Remember to hold the device  
in front of you during a push to talk call so you can see the display. The display informs you when it is your turn to speak. Speak  
towards the microphone, and do not cover the loudspeaker with your hands. Press and hold the voice key the entire time you  
are talking. When you have finished talking, release the key.  
To end the push to talk call, press the end key.  
When you receive a push to talk call, press the call key to answer the call or the end key to dismiss the call.  
Callback requests  
To send a callback request, select Options > PTT contacts, scroll to the desired contact, and select Options > Send callback  
request.  
To answer a callback request, select Show to open the callback request. To make a push to talk call to the sender, press the voice  
key.  
Contacts view  
To view, add, modify, delete, or call contacts, select Options > PTT contacts. A list of names from your device Contacts application  
is displayed with information about their login status.  
To call a selected contact, select Options > Talk 1 to 1. To make a group call, select Options > Make PTT group call.  
To send the contact a request to call you, select Options > Send callback request.  
Copyright © 2006 Nokia. All Rights Reserved.  
24  
           
M a k e c a l l s  
Create a channel  
A channel is like a chat room: you can call the channel to see if anyone is online. The channel call does not alert the other  
participants; the participants just join the channel and start speaking with each other.  
To create a channel, select Options > New channel > Create new.  
Select Options and define the following:  
Channel name — Write the channel name.  
Channel privacy — Select Private or Public.  
Nickname in channel Enter your nickname (20 characters maximum) that is displayed to other users.  
Channel thumbnail — Insert a picture that describes the channel.  
To delete a channel, press the clear key.  
When you log in to push to talk, push to talk automatically connects to the channels that were active when the application was  
last closed.  
Register PTT channels  
To register a channel to the push to talk service, select Options > Register.  
To edit the channel details, select Options > Edit.  
Join a channel  
To join a channel, select Options > PTT channels. Select the channel you want to talk to, and press the voice key. Remember to  
hold the device in front of you during a push to talk call so you can see the display. The display informs you when it is your turn  
to speak. Speak towards the microphone, and do not cover the loudspeaker with your hands. Press and hold the voice key the  
entire time you are talking. When you have finished talking, release the key.  
To switch between channels during multiple calls, select Swap. The active channel is highlighted.  
To view the currently active participants in the channel, select Options > Active members.  
To invite a participant to a channel, select Options > Send invitation.  
Push to talk log  
To open the push to talk log, select Options > PTT log. The log shows the date, time, duration, and other details of your push to  
talk calls.  
Tip: To initiate a one-to-one call from PTT log, select the desired log event and press the voice key.  
Exit push to talk  
Select Options > Exit. Select Yes to log out and close the service. Press No if you want to keep the application active on the  
background.  
Net calls  
Your device supports voice calls over the Internet (Internet calls). Your device attempts emergency calls primarily over cellular  
networks. If an emergency call using cellular networks is not successful, then your device attempts an emergency call through  
your Internet call provider. Due to the established nature of cellular telephony, you should use cellular networks for emergency  
calls, if possible. If you have cellular network coverage available, please make sure that your cellular phone is switched on and  
ready to make calls before you attempt an emergency call. The capability for an emergency call using Internet telephony depends  
on the availability of a WLAN network and your Internet call provider's implementation of emergency call capabilities. Contact  
your Internet call provider to check the Internet telephony emergency call capability.  
VoIP (voice over Internet protocol) technology is a set of protocols that facilitate phone calls over an IP network, such as the  
Internet. VoIP phone calls can be established between computers, between mobile phones, and between a VoIP device and a  
traditional telephone. To make or receive a VoIP call, your device must be within WLAN coverage, for example.  
Before you can make net calls, you need to create a net telephone profile. When the profile is ready, you can make a net call  
from all applications where you can create a regular voice call. To make a net call in standby mode to an address that does not  
start with a digit, press any number key, then press # for a few seconds to clear the display and to switch the device from number  
mode to letter mode. Write the address and press the call key. If you have the fold open, and you have created a net telephone  
profile, write the address and press the call key.  
You must define session initiation protocols (SIP) settings in Menu > Tools > Settings > Connection > SIP settings and VoIP  
settings in Menu > Tools > Settings > Connection > Internet tel. settings. Contact your service provider for more information  
and correct settings.  
Copyright © 2006 Nokia. All Rights Reserved.  
25  
             
M a k e c a l l s  
Preferred profile  
Select Menu > Connect. > Internet tel. to change settings.  
Before you can select the default profile, you must create profiles in Menu > Tools > Settings > Connection > Internet tel.  
settings.  
To select the profile that is used by default when you make net calls, select Preferred profile, and press the joystick. Scroll to the  
desired profile, and press the joystick.  
Register profiles  
Only those profiles where you have selected Registration > When needed setting in Menu > Tools > Settings > Connection > SIP  
settings are shown in the list.  
To change the registration of your net telephone profiles, scroll to the profile that you want to register or unregister, and press  
the joystick. Press the joystick again to select Registered or Not registered.  
To save your settings, select Back.  
Device security  
Select Menu > Tools > Settings > Security > Phone and SIM.  
You can modify the security settings for the PIN code, automatic lock, and SIM card change, and change codes and passwords.  
Avoid using codes that are similar to emergency numbers to prevent accidental dialing of the emergency number.  
Codes are shown as asterisks. When you change a code, enter the current code, then the new code twice.  
Define security settings  
To define device and SIM card settings, select a setting and Options > Change.  
When calls are limited to closed user groups, calls may be possible to the official emergency number programmed into your  
device.  
Define the following settings:  
PIN code request — Select On to request that the PIN code is entered each time the device is switched on. This setting cannot  
be changed if the device is switched off. Some SIM cards do not allow turning off the PIN code request.  
PIN code Change the PIN code. The PIN code must be 4 to 8 numbers long. The PIN code protects your SIM card against  
unauthorized use and is provided with the SIM card. After three consecutive incorrect PIN code entries, the PIN code is blocked,  
and you need to use the PUK code to unblock it before you can use the SIM card again.  
PIN2 code Change the PIN2 code. The PIN2 code must be 4 to 8 numbers long. The PIN2 code is required to access some  
functions of the device and is provided with the SIM card. After three consecutive incorrect PIN2 code entries, the PIN2 code  
is blocked, and you need to use the PUK2 code to unblock it before you can use the SIM card again.  
Autolock period — Set a time-out after which the device is automatically locked and can be used only if the correct lock code  
is entered. Enter a number for the time-out in minutes, or select None to turn off the autolock period. When the device is  
locked, you can still answer incoming calls and calls may still be possible to the official emergency number programmed into  
your device.  
Lock code The new code can be 4-255 characters long. Both alphabets and digits can be used, and both uppercase and  
lowercase alphabets are possible. The device notifies you if the lock code is not properly formatted.  
Lock if SIM changed — Set the device to ask for the lock code when an unknown, new SIM card is inserted into your device.  
The device maintains a list of SIM cards that are recognized as the owners cards.  
Allow remote lock — If you set this option on, you can lock the device by sending a predefined text message from another  
phone. When you set this option on, you need to enter the remote lock message and confirm the message. The message  
must be at least 5 characters long.  
Closed user group (network service) — Specify a group of people to whom you can call and who can call you.  
Confirm SIM services (network service) — Set the device to display confirmation messages when you are using a SIM card  
service.  
Change the barring password  
To change the password used for barring voice, fax, and data calls, select Menu > Tools > Settings > Call barring > Cellular call  
barring > Options > Edit barrings passw.. Enter the current code, then the new code twice. The barring password must be four  
digits long. For details, contact your service provider.  
Fixed dialing  
When fixed dialing is activated, calls may be possible to the official emergency number programmed into your device.  
Select Menu > Contacts > Options > SIM contacts > Fixed dialling contacts.  
Copyright © 2006 Nokia. All Rights Reserved.  
26  
                 
M a k e c a l l s  
With the fixed dialing service, you can restrict calls from your device to only certain phone numbers. Not all SIM cards support  
the fixed dialing service. Contact your service provider for more information.  
Select Options, and select from the following options:  
Activ. fixed dialling Restrict calls from your device. To cancel the service, select Deact. fixed dialling. You need your PIN2  
code to activate and deactivate fixed dialing or edit your fixed dialing contacts. Contact your service provider if you do not  
have the code.  
New SIM contact Add a phone number to the list of numbers to which calls are allowed. Enter the contact name and phone  
number. To restrict calls by a country prefix, enter the country prefix in New SIM contact. All phone numbers to which calls  
are allowed must start with this country prefix.  
Add from Contacts Copy a contact from Contacts to your fixed dialing list.  
Tip: To send text messages to the SIM contacts while the fixed dialing service is active, you need to add the text message  
center number to the fixed dialing list.  
To view or edit a phone number to which calls from your device are allowed, select Options > SIM contacts > Fixed dialling  
contacts.  
To call the contact, press the call key.  
To edit the phone number, select Options > Edit. You may need your PIN2 code to edit your fixed dialing numbers.  
To delete the contact, press the clear key.  
Copyright © 2006 Nokia. All Rights Reserved.  
27  
4.  
Contacts  
Select Menu > Contacts.  
Manage all of your contact information, such as phone numbers and addresses. Add a personal ringing tone, voice tag, or a  
thumbnail image to a contact. Send contact information to compatible devices or receive contact information as business cards  
from compatible devices, and add them to your own list of contacts.  
To add a contact, select Options > New contact. Enter the contact information, and select Done.  
To edit information in a contact card, scroll to the contact, and select Options > Edit. Select from the following options:  
Add thumbnail Add a thumbnail image that will display when a contact calls you. The image must be previously saved to  
your device or memory card.  
Remove thumbnail Remove the image from the contact card.  
Add detail Add fields of information to a contact card, such as Job title.  
Delete detail Delete any details that you added to a contact card.  
Edit label Edit the field names of the contact card.  
Manage contact groups  
Create a contact group so that you can send text or e-mail messages to several recipients at the same time.  
1. Scroll to the right, and select Options > New group.  
2. Enter a name for the group or use the default name, and select OK.  
3. Open the group, and select Options > Add members.  
4. Scroll to each contact you want to add to the group, and press the joystick to mark it.  
5. Select OK to add all marked contacts to the group.  
The following options are available when you select Options in the contact groups view:  
PTT options Make a push to talk call either to an individual or to a group, or send a callback request.  
Open Open the contact group and view the group members.  
Create message — Send a message.  
New group Create a new contact group.  
Delete Delete a contact group.  
Rename Rename the contact group.  
Ringing tone Assign a ringing tone to a contact group.  
Contacts info View the information for a contact group.  
Settings — Set the name display settings for contact group members.  
To remove a contact from a contact group, open the contact group. Scroll to the contact you want to remove, and select  
Options > Remove from group > Yes.  
Tip: To check the group in which a contact belongs, select Menu > Contacts. Scroll to the contact, and select Options >  
Belongs to groups.  
To view or edit a contact within a contact group, open the contact group. Scroll to the contact you want to view or edit, and  
select Options. Select from the following options:  
Open Opens the contact and displays contact information.  
Call — Select Voice call or Video call, and call the contact.  
Create message Create and send a text message or multimedia message to the contact.  
Remove from group Remove the contact from the contact group.  
Belongs to groups View all contact groups that a contact belongs to.  
Manage default information  
Assign a default number or address to a contact so you can easily call or send a message to the default number or address, even  
if several numbers or addresses are saved to that contact.  
To change default information for a contact, open the contact, and select Options > Defaults. Select the number or address you  
want to set as a default, and select OK.  
The default number or address is underlined in the contact.  
Copy contacts between SIM and device memory  
For availability and information on using SIM card services, contact your SIM card vendor. This may be the service provider,  
network operator, or other vendor.  
Copyright © 2006 Nokia. All Rights Reserved.  
28  
               
C o n t a c t s  
To copy contacts from a SIM card to device memory, select Options > SIM contacts > SIM directory to open the SIM directory.  
Mark the contacts you want to copy, or select Mark all to copy all contacts. Select Options > Copy to Contacts.  
To copy contacts from the device memory to a SIM card, select Options > Copy to SIM direct.. Mark the contacts you want to copy,  
or select Mark all to copy all contacts. Select Options > Copy to SIM direct..  
Select Options > SIM contacts > SIM directory to see the names and numbers stored on the SIM card. In SIM directory you can  
add, edit, or copy numbers to Contacts, and you can make calls.  
Select ringing tones for contacts  
Select a ringing tone for a contact or contact group. If the caller's phone number is sent with the call and your device recognizes  
the number, the ringing tone plays when the contact calls you.  
To select a ringing tone for a contact or contacts group, open the contact or contact group, and select Options > Ringing tone.  
A list of ringing tones opens. Select the ringing tone you want to use, and select OK.  
To remove the ringing tone, select Default tone from the list of ringing tones.  
Business cards  
Select Menu > Contacts.  
You can send, receive, view, and save contact cards as business cards in vCard or Nokia Compact Business Card format.  
You can send business cards to compatible devices using SMS, MMS, or e-mail, or an infrared or Bluetooth connection.  
To send a business card, select the contact card from the contacts list, and select Options > Send. Select Via text message, Via  
multimedia, Via e-mail, Via Bluetooth, or Via infrared. Enter the phone number or address, or add a recipient from the contacts  
list. Select Options > Send. If you select SMS as the sending method, contact cards are sent without images.  
To view a received business card, select Open from the displayed notification, or open the message from the inbox folder in  
Messag..  
To save a business card, select Options > Save business card when the incoming message appears on the device.  
To save a received business card, select Options > Save business card.  
To delete a received business card, select Options > Delete.  
Copyright © 2006 Nokia. All Rights Reserved.  
29  
       
5.  
Messages  
Select Menu > Messag..  
Before sending or receiving messages, you may need to do the following:  
Insert a valid SIM card in the device and be located in a service area of the cellular network.  
Verify that the network supports the messaging features you want to use and that they are activated on your SIM card.  
Define Internet access point (IAP) settings on the device. See "Access points," p. 72.  
Define e-mail account settings on the device. See "E-mail account settings," p. 38.  
Define SMS settings on the device. See "Text message settings," p. 33.  
Define MMS settings on the device. See "Multimedia message settings," p. 35.  
The device may recognize the SIM card provider and automatically configure some of the message settings. If not, you may need  
to define the settings manually, or contact your service provider, network operator, or Internet service provider to configure  
the settings.  
The Messag. application displays each type of messaging folder in a list format with the newest message displayed first in each  
folder.  
Select one of the following:  
New message Create and send a new text, multimedia, or e-mail message.  
Inbox View received messages, except e-mails and cell broadcast messages.  
My folders Create your own folders to store messages and templates.  
Mailbox View and reply to received e-mail.  
Drafts — Store messages that have not been sent.  
Sent — Store messages that have been sent.  
Outbox View messages waiting to be sent.  
Reports View information about the delivery of sent messages.  
Organize messages  
To create a new folder to organize your messages, select My folders > Options > New folder. Enter the folder name, and select  
OK.  
To rename a folder, select the folder and Options > Rename folder. Enter the new folder name, and select OK. You can only  
rename folders that you have created.  
To move a message to another folder, open the message, and select Options > Move to folder, the folder, and OK.  
To sort messages in a specific order, select Options > Sort by. You can sort the messages by Date, Sender, Subject, or Message  
type.  
To view the properties of a message, select the message and Options > Message details.  
Search for messages  
To search for a message, open the folder in which you want to search, select Options > Find. Enter the search term, and select  
OK.  
Inbox  
Select Menu > Messag. > Inbox.  
To view a message, scroll to the message, and press the joystick.  
To forward a sent or received message, open the message, and select Options > Forward. It may not be possible to forward  
some messages.  
To reply to a received message, open the message, and select Options > Reply.  
My folders  
To view messages saved in your own folders or to use message templates, select My folders.  
To view a message, scroll to it, and press the joystick.  
To view, edit, create, or send message templates, select Templates, and press the joystick.  
Select Options and from the following:  
Create message — Write and send a message.  
Copyright © 2006 Nokia. All Rights Reserved.  
30  
             
M e s s a g e s  
Sort by Arrange your messages according to sender, type, or other info.  
Move to folder — Save a message in another folder. Scroll to the desired folder, and select OK.  
New folder Create new folders.  
The available options may vary.  
To delete a message or folder, scroll to it, and press the clear key.  
Draft messages  
Messages that you have created, but not yet sent, are stored in the Drafts folder.  
To view or edit a message, scroll to it, and press the joystick.  
To send the message, select Options > Send.  
To delete a message, scroll to it, and press the clear key.  
Tip: To delete multiple messages, scroll to each message, and simultaneously press the edit key and joystick. A check  
mark appears next to these messages. Once you have marked the messages, press the clear key.  
Sent messages  
Your last 20 sent messages are automatically saved in the Sent folder. To change the number of saved messages, select  
Messag. and select Options > Settings > Other.  
Select Options and select from the following:  
Create message — Write and send a message.  
Message details. — View information about the message.  
Sort by Arrange your messages according to sender, type, or other info.  
Move to folder — Save a message in another folder. Scroll to the desired folder, and select OK.  
New folder Create new folders.  
Tip: To move multiple messages, scroll to each message, and simultaneously press the edit key and joystick to mark  
it. Once you have marked the desired messages, select Options > Move to folder.  
The available options may vary.  
To delete a message, scroll to it, and press the clear key.  
Outbox  
Select Menu > Messag. > Outbox.  
To send a message from the Outbox, select the message, and Options > Send.  
To cancel the sending of a message in the Outbox, select the message, and Options > Defer sending.  
Delivery reports  
To keep track of your text and multimedia messages after sending, select Reports.  
You can receive or reject delivery reports in text message and multimedia message settings. Select Options > Settings > Text  
msg. or Multimedia message > Receive report.  
Tip: To call a message recipient, scroll to the delivery report, and press the call key.  
Messaging settings  
Select Options > Settings.  
To define or edit settings for different message types, select Text message, Multimedia message, E-mail, Service message, Cell  
broadcast, or Other.  
Other settings  
Select Menu > Messag. > Options > Settings > Other.  
Select from the following:  
Save sent messages — Select whether to store sent messages in the Sent folder.  
Copyright © 2006 Nokia. All Rights Reserved.  
31  
               
M e s s a g e s  
No. of saved msgs. Enter the number of sent messages that you want to save. When the limit is reached, the oldest message  
is deleted.  
Folder view Define how you want the messages in the inbox to be shown.  
Memory in use — Select where to save your received messages. You can save messages to memory card only if a memory  
card is inserted.  
The settings available for editing may vary.  
Text message center settings  
Select Options > Settings > Text msg. > Message centres.  
To edit message centers, select the message center, and Options > Edit.  
To add new message centers, select Options > New msg. centre.  
To delete message centers, select the message center, and press the clear key.  
Text messages  
Your device supports the sending of text messages beyond the character limit for a single message. Longer messages are sent  
as a series of two or more messages. Your service provider may charge accordingly. Characters that use accents or other marks,  
and characters from some language options like Chinese, take up more space limiting the number of characters that can be sent  
in a single message.  
Write and send text messages  
Select Menu > Messag. > New message > Text message.  
1. In the To field, press the joystick to select recipients from Contacts, or enter the recipients' mobile phone numbers manually.  
If you enter more than one number, separate the numbers with a semicolon. To insert a semicolon, press *.  
2. Enter the text of the message. To use a template, select Options > Insert > Template.  
3. Select Options > Send to send the message.  
Note: When sending messages, your device may display Message Sent. This is an indication that the message has  
been sent by your device to the message center number programmed into your device. This is not an indication  
that the message has been received at the intended destination. For more details about messaging services, check  
with your service provider.  
Sending options for text messages  
To set sending options for the text message, select Options > Sending options.  
Define the following:  
Msg. centre in use — Select a message center to send the message.  
Character encoding — Select Reduced support to use automatic character conversion to another encoding system when  
available.  
Receive report — Select Yes if you want that the network sends you delivery reports on your messages (network service).  
Message validity — Select how long the message center resends your message if the first attempt fails (network service). If  
the recipient cannot be reached within the validity period, the message is deleted from the message center.  
Message sent as Convert the message to another format, such as Text, Fax, Paging or E-mail. Change this option only if you  
are sure that your message center is able to convert text messages into these other formats. Contact your network operator.  
Reply via same ctr. — Select whether you want the reply message to be sent using the same text message center number  
(network service).  
Reply to received text messages  
To reply to a text message, open the message from the Inbox. Select Options > Reply. Enter the text of the message, and select  
Options > Send.  
To call the sender of a text message, open the message from the Inbox, and select Options > Call.  
Text messages on the SIM card  
Text messages may be stored on your SIM card. Before you can view SIM messages, you must copy the messages to a folder in  
the device. After copying the messages to a folder, you can view them in the folder or delete them from the SIM card.  
Select Options > SIM messages.  
1. Select Options > Mark/Unmark > Mark or Mark all to mark every message.  
2. Select Options > Copy.  
3. Select a folder and OK to begin copying.  
Copyright © 2006 Nokia. All Rights Reserved.  
32  
                   
M e s s a g e s  
To view SIM card messages, open the folder where you copied the messages, and open a message.  
To delete a text message from the SIM card, select the message, and press the clear key.  
Text message settings  
Select Options > Settings > Text msg..  
Define the following:  
Message centres View the available message centers for your device.  
Msg. centre in use — Select a message center to send the message.  
Character encoding — Select Reduced support to use automatic character conversion to another encoding system when  
available.  
Receive report — Select Yes if you want that the network sends you delivery reports on your messages (network service).  
Message validity — Select how long the message center resends your message if the first attempt fails (network service). If  
the recipient cannot be reached within the validity period, the message is deleted from the message center.  
Message sent as Convert the message to another format, such as Text, Fax, Paging or E-mail. Change this option only if you  
are sure that your message center is able to convert text messages into these other formats. Contact your network operator.  
Preferred conn. — Select the preferred method of connection when sending text messages from your device.  
Reply via same ctr. — Select whether you want the reply message to be sent using the same text message center number  
(network service).  
Picture messages  
Note: Picture message function can be used only if it is supported by your network operator or service provider. Only  
devices that offer picture message features can receive and display picture messages.  
Select Menu > Messag..  
To view a picture message, open the message from the Inbox folder.  
Select Options and select from the following:  
Message details View information about the message.  
Move to folder — Save the message in a different folder.  
Add to Contacts Add the sender of the message to your contacts.  
Find Find phone numbers and addresses that the message may contain.  
Forward picture messages  
Copyright protections may prevent some images, ringing tones, and other content from being copied, modified, transferred or  
forwarded.  
1. In the Inbox, open a picture message and select Options > Forward.  
2. In the To field, enter a recipient's number, or press the joystick to add a recipient from Contacts. If you enter more than one  
number, separate the numbers with a semicolon. To insert a semicolon, press *.  
3. Enter the text of your message. The text can have 120 characters. To use a template, select Options > Insert > Template.  
4. To send the message, press the call key.  
Tip: To remove the picture from the message, select Options > Remove picture.  
Multimedia messages  
A multimedia message (MMS) can contain text and objects such as images, sound clips, or video clips.  
Note: Only devices that have compatible features can receive and display multimedia messages. The appearance of a  
message may vary depending on the receiving device.  
Before you can send or receive multimedia messages on your device, you must define the multimedia message settings. Your  
device may have recognized the SIM card provider and automatically configured the multimedia message settings. If not, contact  
Create and send multimedia messages  
The default setting of the multimedia message service is generally on.  
Select New message > Multimedia message.  
Copyright protections may prevent some images, ringing tones, and other content from being copied, modified, transferred or  
forwarded.  
1. In the To field, press the joystick to select recipients from Contacts, or enter the recipients' mobile phone numbers or e-mail  
addresses manually.  
Copyright © 2006 Nokia. All Rights Reserved.  
33  
                 
M e s s a g e s  
2. In the Subject field, enter a subject for the message. To change the fields that are visible, select Options > Address fields.  
3. Enter the text of the message, and select Options > Insert object to add media objects. You can add objects such as Image,  
Sound clip, or Video clip.  
The wireless network may limit the size of MMS messages. If the inserted picture exceeds this limit, the device may make it  
smaller so that it can be sent by MMS.  
4. Each slide of your message can contain only one video or audio clip. To add more slides to your message, select Options >  
Insert new > Slide. To change the order of slides in your message, select Options > Move.  
5. To preview a multimedia message before sending it, select Options > Preview.  
6. Press the joystick to send the multimedia message.  
Tip: You can also create multimedia messages directly from several applications, such as Contacts and Gallery.  
To delete an object from a multimedia message, select Options > Remove.  
Sending options for multimedia messages  
Select Options > Sending options and from the following options:  
Receive report — Select Yes if you want to receive a notification when the message has been successfully delivered to the  
recipient. Receiving a delivery report of a multimedia message that has been sent to an e-mail address may not be possible.  
Message validity — Select how long the messaging center tries to send the message. If the recipient of a message cannot be  
reached within the validityperiod, the message is removed from the multimedia messaging center. The networkmust support  
this feature. Maximum time is the maximum amount of time allowed by the network.  
Create presentations  
Select New message > Multimedia message.  
1. In the To field, press the joystick to select recipients from Contacts, or enter the recipients' mobile phone numbers or e-mail  
addresses manually.  
2. Select Options > Create presentation and a presentation template.  
Tip: A template may define which media objects you can include in the presentation, where they appear, and which  
effects are displayed between images and slides.  
3. Scroll to a text area and enter the text.  
4. To insert images, sound, video, or notes in your presentation, scroll to the corresponding object area, and select Options >  
Insert.  
Tip: To move between object areas, scroll up and down.  
5. To add slides, select Insert > New slide.  
6. Select Options and from the following:  
Preview — See what your multimedia presentation looks like when it is opened. Multimedia presentations may only be  
viewed in compatible devices that support presentations. They may appear different in different devices.  
Backgrnd. settings — Select the background color for the presentation and background images for different slides.  
Effect settings — Select effects between images or slides.  
Creating multimedia presentations is not possible if MMS creation mode is Restricted. To change MMS creation mode, select  
Messag. > Options > Settings > Multimedia message.  
The available options may vary.  
To send your multimedia presentation, press the call key.  
Tip: To save the message in Drafts without sending it, select Done.  
Receive and reply to multimedia messages  
Important: Multimedia message objects may contain viruses or otherwise be harmful to your device or PC. Do not  
open any attachment if you are not sure of the trustworthiness of the sender.  
Before you can send or receive multimedia messages on your device, you must define the multimedia message settings. Your  
device may have recognized the SIM card provider and automatically configured the multimedia message settings. If not, contact  
If you receive multimedia messages containing objects unsupported by your device, you cannot open them.  
1. To reply to a multimedia message, open the message from the Inbox, and select Options > Reply.  
2. Select Options > To sender to reply to the sender with a multimedia message or Options > Via text message to reply to the  
sender with a text message.  
Copyright © 2006 Nokia. All Rights Reserved.  
34  
     
M e s s a g e s  
Tip: To add recipients to your reply, select Options > Add recipient to select the recipients of the message from the  
contacts list, or enter the recipients' phone numbers or e-mail addresses manually in the To field.  
3. Enter the text of the message, and press the joystick to send it.  
View presentations  
Open the Inbox, scroll to a multimedia message that contains a presentation, and press the joystick. Scroll to the presentation,  
and press the joystick.  
To pause the presentation, press either selection key below the display.  
After you pause the presentation or playing finishes, select Options and from the following:  
Open link Open a Web link and browse the Web page.  
Activate scrolling — Scroll text or images too large to fit on the display.  
Continue Resume playing the presentation.  
Play Replay the presentation from the start.  
Find Find phone numbers and e-mail or Web addresses the presentation may contain. You may use these numbers and  
addresses to make calls, send messages, or create bookmarks, for example.  
The available options may vary.  
View media objects  
Open the Inbox, scroll to a received multimedia message and press the joystick. Select Options > Objects.  
To view or play a media object, scroll to it, and press the joystick.  
Media objects and message attachments may contain viruses or other harmful software. Do not open any objects or attachments  
unless you are sure of the trustworthiness of the sender.  
To save a media object in its corresponding application, scroll to the object, select Options > Save.  
To send a media object to compatible devices, scroll to it, and select Options > Send.  
Tip: If you receive multimedia messages that contain media objects your device cannot open, you may be able to send  
these objects to another device such as a computer.  
View and save multimedia attachments  
To view multimedia messages as complete presentations, open the message, and select Options > Play presentation.  
Tip: If you have selected a multimedia object in a multimedia message, to view or play them, select View image, Play  
sound clip, or Play video clip.  
To view the name and size of an attachment, open the message, and select Options > Objects.  
To save a multimedia object, select Options > Objects, the object, and Options > Save.  
Multimedia message settings  
Select Options > Settings > Multimedia message.  
Define the following settings:  
Image size — Select Small or Large to scale images in multimedia messages. Select Original to maintain the original image  
size of multimedia messages.  
MMS creation mode — Select Restricted to have your device prevent you from including content in multimedia messages that  
may not be supported by the network or the receiving device. To receive warnings about including such content, select  
Guided. To create a multimedia message with no restrictions on attachment type, select Free. If you select Restricted, creating  
multimedia presentations is not possible.  
Access point in use — Select the default access point to connect to the multimedia message center. You may not be able to  
change the default access point if it is preset in your device by your service provider.  
Multimedia retrieval — Select Always automatic to always receive multimedia messages automatically, Auto. in home  
network to receive notification of a new multimedia message that you can retrieve from the message center (for example,  
when you are traveling abroad and are outside your home network), Manual to retrieve multimedia messages from the  
message center manually, or Off to prevent receipt of any multimedia messages.  
Allow anon. msgs. — Select whether you want to receive messages from unknown senders.  
Receive adverts — Select whether you want to receive messages defined as advertisements.  
Receive report — Select Yes to have the status of the sent message to be shown in the log (network service). Receiving a  
delivery report of a multimedia message that has been sent to an e-mail address may not be possible.  
Deny report sending — Select Yes to not send delivery reports from your device for received multimedia messages.  
Copyright © 2006 Nokia. All Rights Reserved.  
35  
           
M e s s a g e s  
Message validity — Select how long the messaging center tries to send the message (network service). If the recipient of a  
message cannot be reached within the validity period, the message is removed from the multimedia messaging center.  
Maximum time is the maximum amount of time allowed by the network.  
E-mail messages  
To receive and send mail, you must have a remote mailbox service. This service may be offered by an Internet service provider,  
a network service provider, or your company. Your device is compliant with Internet standards SMTP, IMAP4 (revision 1), and  
POP3, and with different push e-mail solutions. Other e-mail providers may offer services with different settings or features  
than those described in this user guide. Contact your e-mail provider or service provider for more details.  
Before you can send, receive, retrieve, reply to, and forward mail on your device, you must also do the following:  
Configure an Internet access point (IAP). See "Access points," p. 72.  
Set up an e-mail account, and define the e-mail settings correctly. See "E-mail account settings," p. 38.  
Follow the instructions from your remote mailbox and Internet service providers. Contact your network and Internet service  
providers or operator for the correct settings.  
Set up your e-mail  
If you select Mailbox and have not set up your e-mail account, you are prompted to do so. To start setting up the e-mail account  
with the mailbox guide, select Yes.  
1. To start entering the e-mail settings, select Start.  
2. In Mailbox type, select IMAP4 or POP3, and select Next.  
Tip: POP3 is a version of the post office protocol that is used to store and retrieve e-mail or Internet mail messages.  
IMAP4 is a version of the Internet message access protocol that lets you access and manage e-mail messages while  
the messages are still on the e-mail server. You can then choose which messages to download to your device.  
3. In My e-mail address, enter your e-mail address. To insert @ or other special characters, press *. To insert a full stop, press  
1. Select Next.  
4. In Incoming mail serv., enter the name of the remote server that receives your e-mail, and select Next.  
5. In Outgoing mail serv., enter the name of the remote server that sends your e-mail, and select Next. Depending on your  
mobile operator, you might have to use your mobile operator's outgoing mail server instead of your e-mail provider's.  
6. In Access point, select the Internet access point your device should use when it retrieves the e-mails. If you select Always  
ask, each time the device starts to retrieve e-mail, it asks which Internet access point it should use, but if you select an access  
point, the device makes the connection automatically. Select Next.  
Tip: If you select Select group, the device makes the connection automatically using the best available Internet  
access point from the access point group. Select the access point group, and Back to save the selection.  
7. Enter a name for your new mailbox, and select Finish.  
When you create a new mailbox, the name you give to the mailbox replaces Mailbox in the Messag. main view. You can have  
up to six mailboxes.  
Select your default mailbox  
If you have defined several mailboxes, you can select one of them as your default mailbox. To define the default mailbox, select  
Options > Settings > E-mail > Mailbox in use and the mailbox.  
If you have defined several mailboxes, you must select the mailbox that you want to use every time you start composing a new  
e-mail message.  
Connect to mailbox  
E-mail addressed to you is not automatically received by your device, but by your remote mailbox. To read your e-mail, you must  
first connect to the remote mailbox; then select the e-mails you wish to retrieve into your device. To receive and send e-mail,  
you need to register for an e-mail service. To set up a mailbox in your device, select Messag. > Options > Settings > E-mail >  
Options > New mailbox. Contact your service provider for the correct settings.  
To retrieve received e-mail messages to your device and view them offline, select your mailbox in the Messag. main view. When  
the device asks Connect to mailbox?, select Yes.  
To view e-mail messages in a folder, scroll to the folder, and press the joystick. Scroll to a message, and press the joystick.  
To retrieve e-mail messages to your device, select Options > Retrieve e-mail > New to retrieve new messages that you have  
neither read nor retrieved, Selected to retrieve only messages you select from the remote mailbox, or All to retrieve all messages  
not previously retrieved.  
To disconnect from a remote mailbox, select Options > Disconnect.  
Copyright © 2006 Nokia. All Rights Reserved.  
36  
       
M e s s a g e s  
View e-mail offline  
Working offline means that your device is not connected to a remote mailbox. Managing your e-mail offline enables you to save  
in connection costs and work in conditions that do not allow a data connection. Any changes you make in the remote mailbox  
folders while offline take effect in your remote mailbox the next time you go online and synchronize. For example, if you delete  
an e-mail from your device when offline, the e-mail is deleted from the remote mailbox the next time you connect to the mailbox.  
1. Select Messag. > Options > Settings > E-mail. Select the e-mail account, and press the joystick. Select Retrieval settings > E-  
mail to retrieve > Msgs. & attachs. to retrieve entire messages with their attachments to your device.  
2. Open your mailbox, and select Options > Retrieve e-mail. Select New to retrieve new messages that you have neither read  
nor retrieved, Selected to retrieve only messages you select from the remote mailbox, or All to retrieve all messages not  
previously retrieved. The device goes online and connects to the mailbox to retrieve the mails.  
3. After retrieving the e-mails, select Options > Disconnect to return to the offline mode.  
4. To view an e-mail message, scroll to it, and press the joystick.  
Some options require you to connect to your remote mailbox.  
Tip: To subscribe to other folders in your remote mailbox, select E-mail settings > Retrieval settings > Folder  
subscriptions. E-mail in all subscribed folders is updated when you retrieve e-mail from your remote mailbox.  
Read and reply to e-mail  
Important: E-mail messages may contain viruses or otherwise be harmful to your device or PC. Do not open any  
attachment if you are not sure of the trustworthiness of the sender.  
To read a received e-mail, scroll to the e-mail, and press the joystick.  
To search for an e-mail in your mailbox, select Options > Find. Enter the search term, and select OK.  
To open an attachment, select Options > Attachments. Scroll to the attachment, and press the joystick.  
To reply only to the sender of an e-mail, open the e-mail, and select Options > Reply > To sender.  
To reply to all recipients of an e-mail, open the e-mail, and select Options > Reply > To all.  
To delete an attachment from an e-mail that you are sending, select the attachment and Options > Attachments > Remove.  
Tip: If you reply to an e-mail that contains attached files, the attachments are not included in the reply. If you forward  
the received e-mail, attachments are included.  
To set the message priority, select Options > Sending options > Priority and from the available options.  
To call the sender of the e-mail, open the e-mail, and select Options > Call.  
To reply to the sender of the e-mail with a text message or multimedia message, open the e-mail, and select Options > Create  
message.  
To forward an e-mail, open the e-mail, and select Options > Forward.  
Delete messages  
To free up memory space on your device, regularly delete messages from the Inbox and Sent folders, and delete retrieved e-  
mail messages.  
To delete a message, scroll to it, and press the clear key.  
You can select to delete local e-mail messages on the device and keep the original on the server, or you can delete both the  
local e-mail messages on the device and the original messages on the server.  
To delete e-mails from the device only, select Options > Delete > Phone only.  
To delete e-mail both from the device and from the remote server, open an e-mail, and select Options > Delete > Phone and  
server.  
E-mail folders  
If you create subfolders in your IMAP4 mailboxes on a remote server, you can view and manage these folders with your device.  
You can only subscribe to folders in your IMAP4 mailboxes. Subscribing to folders in a remote mailbox allows you to view those  
folders on your device.  
To view folders in your IMAP4 mailbox, establish a connection, and select Options > E-mail sett. > Retrieval settings > Folder  
subscriptions.  
To view a remote folder, select a folder and Options > Subscribe. Every time you go online, the subscribed folders are updated.  
This may take some time if the folders are large.  
To update the list of folders, select a folder and Options > Update folder list.  
Copyright © 2006 Nokia. All Rights Reserved.  
37  
           
M e s s a g e s  
Write and send e-mail  
To write an e-mail, select Options > Add recipient to select the recipients' e-mail addresses from the contacts list, or enter the  
e-mail addresses in the To field. Use a semicolon to separate entries. Scroll down, and use the Cc field to copy other recipients,  
or the Bcc field to blind copy recipients. In the Subject field, enter the subject of the e-mail. Enter your e-mail message in the  
text area, and select Options > Send.  
To attach a file to an e-mail, select Options > Insert, and select the attachment you want to add. For example, you can insert  
images, sound clips, notes and other files such as office files.  
To set the sending time for an e-mail message, select Options > Sending options > Send message. Select Immediately or During  
next conn. if you are working offline.  
E-mail messages are stored in the Outbox before sending. Unless the e-mail is sent immediately, you can open the Outbox and  
suspend and resume sending or view the e-mail.  
E-mail account settings  
Select Menu > Messag. > Mailbox.  
The settings available for editing may vary. Some settings may be preset by your service provider.  
If you try to edit mailbox settings but have not set up an e-mail account, the mailbox guide opens and helps you set up your e-  
mail account.  
Settings for the received e-mail  
Select Incoming e-mail and from the following settings:  
User name Enter the user name for the e-mail service.  
Password Enter the password for the e-mail service.  
Incoming mail serv. Enter the IP address or host name of the server that receives your e-mail.  
Access point in use — Select the Internet access point that the device uses for retrieving the e-mail messages that you receive.  
Default mailbox Enter a name for the mailbox.  
Mailbox type — Select the mailbox protocol that your remote mailbox service provider recommends. The options are POP3  
and IMAP4. This setting can be selected only once and cannot be changed if you have saved or exited from the mailbox  
settings. If you use the POP3 protocol, e-mail messages are not updated automatically when you are online. To see the latest  
e-mail messages, you must disconnect and make a new connection to your mailbox.  
Security (ports) — Select the security option used to increase the security of the connection.  
Port Define a port for connection.  
APOP secure login (for POP3 only) — Use with the POP3 protocol to encrypt the sending of passwords to the remote e-mail  
server while connecting to the mailbox.  
Settings for sent e-mail  
Select Outgoing e-mail and from the following settings:  
My e-mail address Enter the e-mail address given to you by your service provider. Replies to your messages are sent to  
this address.  
User name Enter the user name for the e-mail service.  
Password Enter the password for the e-mail service.  
Outgoing mail serv. Enter the IP address or host name of the mail server that sends your e-mail. You may only be able to  
use the outgoing server of your network operator. Contact your service provider for more information.  
Access point in use — Select the Internet access point that the device uses for sending the e-mail messages that you send.  
Security (ports) — Select the security option used to secure the connection to the remote mailbox.  
Port Define a port for connection.  
User settings  
Select User settings and from the following settings:  
My name Enter a name to appear before your e-mail address when you send e-mail.  
Reply-to — Select whether you want replies to be redirected to a different address. Select On, and enter the e-mail address  
to which you want to direct the replies. You can only enter one address to which replies are directed.  
Delete e-mails from — Select whether you want to delete the e-mails only from the device or from both the device and the  
server. Select Always ask if you want to confirm from where the e-mail should be deleted every time you delete an e-mail.  
Send message — Select to send the e-mail as soon as possible, to send it the next time you retrieve e-mail, or to store the e-  
mail in the Outbox, from where you can send it later.  
Send copy to self — Select whether you want to save a copy of the e-mail to your remote mailbox and to the address defined  
in My e-mail address in the settings for Outgoing e-mail.  
Include signature — Select whether you want to attach a signature to your e-mail messages.  
New e-mail alerts — Select whether you want to receive the new e-mail indications, a tone and a note, when new mail is  
received to the mailbox.  
Copyright © 2006 Nokia. All Rights Reserved.  
38  
         
M e s s a g e s  
Default encoding — Select the preferred method for character encoding.  
Retrieval settings  
Select Retrieval settings and from the following settings:  
E-mail to retrieve (for POP3 mailboxes only) — Select whether you want to retrieve only the e-mail header information such  
as sender, subject and date, e-mail, or e-mail with attachments.  
Retrieval amount — Select the number of e-mails you want to retrieve from the remote server to your mailbox.  
IMAP4 folder path (for IMAP4 mailboxes only) — Define the folder path for folders to be subscribed.  
Folder subscriptions (for IMAP4 mailboxes only) — Subscribe to other folders in the remote mailbox and retrieve content  
from those folders.  
Automatic retrieval settings  
Select Automatic retrieval and from the following settings:  
E-mail notifications — Select whether you want to receive notifications when new e-mail is received in your remote mailbox.  
Select Always enabled to always automatically retrieve new e-mail messages from your remote mailbox, or Only in home  
net. to automatically retrieve new e-mail messages from your remote mailbox only when you are in your home network and  
not, for example, traveling.  
Retrieval days — Select the days on which e-mails are retrieved to your device.  
Retrieval hours Define the hours between which the e-mails are retrieved.  
Retrieval interval — Select the time interval between retrieving new e-mails.  
Instant messaging  
Select Menu > Connect. > IM.  
Instant messaging (IM) (network service) allows you to converse with other people using instant messages and join discussion  
forums (IM groups) with specific topics. Various service providers maintain IM servers that you can log in to after you register  
to an IM service. Service providers may differ in their support of features.  
If IM is not available from your wireless service provider, it may not appear in the menu of your device. Contact your service  
provider for more information about signing up for IM services and costs for services. For more information on the availability  
of IM settings, contact your network operator, service provider, or dealer.  
You may receive the settings in a special text message from the network operator or service provider that offers the IM service.  
You must save the settings to access the service that you want to use. You can also enter the settings manually.  
Connect to an IM server  
To converse with an IM user or users, and to view and edit your IM contacts, you must log into the instant messaging server.  
Open IM, and select Options > Login. Enter your user ID and password, and press the joystick to log in. You can obtain the user  
name, password, and other settings to log in from your service provider when you register for the service.  
Tip: To have instant messaging connect to the server automatically when you open the application, select Options >  
Settings > Server settings > IM login type > On app. start-up.  
Search IM users or IM groups  
To search for IM users and user IDs, select IM contacts > Options > New IM contact > Search. You can search by User's name, User  
ID, Phone number, and E-mail address.  
To search for IM groups and group IDs, select IM groups > Options > Search. You can search by Group name, Topic, and  
Members (user ID).  
Scroll to a found IM user or group, and select Options and from the following:  
New search Conduct another search.  
More results View the remaining found IM users or groups, if any.  
Previous results View the IM users or groups that were found in the previous search.  
Open conversation — Start a conversation with the user if the user is online.  
Add to IM contacts — Save the user in one of your IM contacts lists.  
Send invitation — Invite the IM user to an IM group.  
Blocking options — Prevent or allow the reception of messages from the IM user.  
Join Join the IM group.  
Save — Save the group.  
Conversations with a single IM user  
The Conversations view shows a list of the individual conversation participants with whom you have an ongoing conversation.  
Ongoing conversations are automatically closed when you exit IM.  
Copyright © 2006 Nokia. All Rights Reserved.  
39  
             
M e s s a g e s  
To view a conversation, scroll to a participant, and press the joystick.  
To continue the conversation, enter your message, and press the joystick.  
To return to the conversations list without closing the conversation, select Back. To close the conversation, select Options > End  
conversation.  
To start a new conversation, select Options > New conversation. You can start a new conversation with a different contact while  
you are inside another active conversation. However, you cannot have two active conversations with the same contact.  
To insert an image to an instant message, select Options > Send image, and select the image you want to send.  
To save a conversation participant to your IM contacts, select Options > Add to IM contacts.  
To save a conversation, while in the conversation view, select Options > Record chat. The conversation is saved as a text file that  
can be opened and viewed in the Notes application.  
To send automatic replies to incoming messages, select Options > Set auto reply on. You can still receive messages.  
IM groups  
The IM groups view shows a list of the IM groups that you have saved or to which you are currently joined.  
IM groups is available only if you logged into an IM server when you opened the IM application, and the server supports IM  
groups.  
To create an IM group, select Options > Create new group.  
To join an IM group or to continue a group conversation, scroll to the group, and press the joystick. Enter a message, and press  
the call key to send it.  
To join an IM group that is not on the list, but for which you know the group ID, select Options > Join new group.  
To leave the IM group, select Options > Leave IM group.  
You can also select Options and from the following:  
Group — Select Save to save the group to your IM groups, View participants to view the current members of the group, or  
Settings to edit the group settings. You can only select this option if you have editing rights to the group.  
Login Connect to an instant messaging server if you did not log in when you opened the application.  
Logout Disconnect from the IM server.  
Settings Edit instant messaging application or server settings.  
To remove an IM group, press the clear key.  
Group conversations  
To join the conversation, select a group.  
Select Options and from the following:  
Insert smiley Add a smiley in your message.  
Send private msg. — Send a private message to one or several, but not all, members of the IM group.  
Reply — Send a message only to the sender of the open message.  
Forward Forward the open message to another IM group or contact.  
Send invitation — Invite an IM user to join the group.  
Leave IM group End instant messaging in the group.  
Group — Select Save to save the group to your IM groups, View participants to view the current members of the group, or  
Settings to edit the group settings. You can only select this option if you have editing rights to the group.  
Record chat — Save a copy of the group conversation.  
To send a message, enter the message, and press the call key.  
IM group settings  
Select IM groups > Options > Group > Settings.  
You can only edit IM group settings if you have editing rights to that group.  
Select from the following settings:  
Group name: Enter a name for the IM group.  
Group ID The group ID is created automatically and cannot be added or changed.  
Group topic Enter a topic for the group conversation.  
Welcome note Enter a note that greets IM users once they join the group.  
Group size Enter the maximum number of IM users that can join the group.  
Allow search — Select whether you want to allow IM users to find the group when searching.  
Copyright © 2006 Nokia. All Rights Reserved.  
40  
     
M e s s a g e s  
Editing rights To provide other members of the group with editing rights to the group, select Selected > Options > Add  
editor. IM users with editing rights can edit group settings and invite other users to join the group or ban them from it.  
Group members To close the group and allow only selected IM users to join it, select Selected only > Options > Add  
member.  
Banned list To prevent some IM users from joining the group, select Options > Add to banned list.  
Allow private msgs. To prevent group members from sending private messages between themselves, select No.  
Group editing rights  
To add editing rights to or remove them from IM group members, scroll to the IM group, and select Options > Group >  
Settings > Editing rights > Selected.  
Tip: IM users with editing rights can edit group settings and invite other users to join the group or ban them from the  
group.  
To provide members with editing rights to the group, select Options > Add editor and from the following:  
From IM contacts Add one or several of your IM contacts.  
Enter user ID Enter the ID of the IM user.  
To remove editing rights from a group member, select Options > Remove.  
Ban from groups  
Scroll to the IM group, and select Options > Group > Settings > Banned list.  
To prevent IM users from joining the group, select Options > Add to banned list and from the following:  
From IM contacts Ban one or several of your IM contacts.  
Enter user ID Enter the ID of the IM user.  
To allow a banned user to join the group, select Options > Remove.  
IM contacts  
When login to an IM service is complete, your contact list for the service provider is retrieved automatically. If your contact list  
is not available, wait a few minutes and try to retrieve your contacts list manually.  
Tip: The online status of your IM contacts is shown by an indicator next to the contact name.  
To create an IM contact card, select Options > New IM contact. Enter the user ID and a nickname, and select Done. The user ID  
can be up to 50 characters, and the IM service provider may require the user ID to be in the [email protected] format.  
The nickname is optional.  
To view a different list of your IM contacts, select Options > Change contact list.  
Scroll to an IM contact, select Options and from the following:  
Open conversation — Start or continue instant messaging with the contact.  
Contact details View the contact card.  
Editing options Edit or delete the contact card, move it to another contact list, or receive a note when the contact's online  
status changes.  
Belongs to groups — See the IM groups the contact has joined.  
New contact list Create a contact list for a specific group of IM contacts.  
Reload users' availab. Update the online status of your IM contacts.  
Blocking options — Prevent or allow the reception of messages from the contact.  
Login Connect to an instant messaging server if you did not log in when you opened the application.  
Logout Disconnect from the IM server.  
Settings Edit instant messaging application or server settings.  
The available options may vary.  
To delete an IM contact, press the clear key.  
Blocked contacts  
Select IM contacts > Options > Blocking options > View blocked list.  
To find a blocked IM user, enter the first letters of the user's name. Matching names appear in a list.  
To allow receiving messages from a blocked IM user, select Options > Unblock.  
To prevent receiving messages from other IM users, select Options > Block new contacts. Select the IM user from your IM contacts,  
or enter the user ID.  
Copyright © 2006 Nokia. All Rights Reserved.  
41  
       
M e s s a g e s  
View invitations  
Select Conversations. Scroll to an invitation, and press the joystick.  
Select Options and from the following:  
Join Join the instant messaging group.  
Reject Reject the invitation and send a message to its sender.  
Delete Delete the invitation.  
Blocking options — Prevent the reception of invitations from this sender.  
Recorded messaging  
To view a recorded conversation, select Record. chats, scroll to a conversation, and press the joystick.  
You can also scroll to a recorded conversation, and select Options and select from the following:  
Send — Send the IM session to a compatible device.  
Login Connect to an instant messaging server if you did not log in when you opened the application. To disconnect, select  
Logout.  
Settings Edit instant messaging application or server settings.  
To delete an IM conversation, press the clear key.  
Settings  
Select Options > Settings > IM settings.  
Select from the following settings:  
Use screen name To change the name that identifies you in IM groups, select Yes.  
Allow messages from — Select to receive instant messages from all other IM users, your IM contacts only, or not to receive  
messages at all.  
Allow invitations from — Select to receive invitations to IM groups from all IM users, your IM contacts only, or not to receive  
invitations at all.  
Msg. scrolling speed To decrease or increase the speed at which new messages are displayed, scroll left or right.  
Sort IM contacts — Select to list your IM contacts alphabetically or by their online status.  
Availabil. reloading To update the online status of your IM contacts automatically, select Automatic.  
Offline contacts — Select if IM contacts with an offline status are shown in the IM contacts list.  
The settings available for editing may vary. Contact your service provider for more information.  
IM server settings  
Select Options > Settings > Server settings.  
Scroll to the following options, and press the joystick to configure your IM server:  
Servers Add new, edit, or delete servers.  
Default server Change the server to which your device automatically logs into, scroll to the desired server, and press the  
joystick.  
IM login type To establish a connection between your device and the default server automatically, select Automatic. Select  
Auto. in home network to automate the connection when in your home network. Select On app. start-up to connect to the  
server when you open the messaging application. Select Manual to connect to the server manually at any time.  
Special messages  
Your device can receive many kinds of messages that contain data:  
Operator logo To save the logo, select Options > Save.  
Ringing tone To save a ring tone, select Options > Save.  
Configuration message You may receive settings from your network operator, service provider, or company information  
management department in a configuration message. To accept the settings, open the message, and select Options > Save  
all.  
E-mail notification The note tells you how many new e-mails you have in your remote mailbox. An extended notification  
may list more detailed information.  
Send service commands  
Send a service request message to your service provider and request activation for certain network services.  
To send a service request to your service provider, select Options > Service command. Enter the service request as a text message,  
and select Options > Send.  
Copyright © 2006 Nokia. All Rights Reserved.  
42  
               
6.  
Connectivity  
Copyright protections may prevent some images, music (including ringing tones), and other content from being copied,  
modified, transferred or forwarded.  
Your device offers several options to connect to the Internet, a corporate intranet, or to another device or PC. Wireless methods  
include wireless LAN, Bluetooth, and infrared. Your device supports a wired solution with a USB (Universal Serial Bus) cable  
connection for Nokia PC Suite or IP passthrough. Your device also allows you to communicate using net calls (Voice over IP),  
push to talk, instant messaging (chat), and modem-based connections.  
Internet access points  
An access point is where your device connects to a network. To use e-mail and multimedia services or to connect to the Internet  
and browse web pages, you must first define Internet access points for these services. You may need to set up several Internet  
access points, depending on the sites you want to access. For example, browsing the Web may require one access point, and  
accessing your company intranet may require another. To connect to the Internet over GPRS, your device may have predefined,  
default Internet access point settings.  
When you switch on your device for the first time, the access points may be configured automatically based on the service  
provider information in your SIM card. You can also receive the access points settings in a message from your service provider.  
This might reduce the number of settings you need to enter yourself.  
The available options may vary. Some or all access points may be preset for your device by your service provider. You may not  
be able to add, edit, or delete access points.  
Contact your service provider and e-mail service provider for more information on access points and their settings.  
Set up an Internet access point for data calls  
1. Select Menu > Tools > Settings > Connection > Access points.  
2. Select Options > New access point. To use an existing access point as a basis for the new one, select Use existing settings. To  
start with an empty access point, select Use default settings.  
3. Define the following settings.  
Connection name Enter a descriptive name for the connection.  
Data bearer — Select Data call or High speed data (GSM only).  
Dial-up number Enter the modem telephone number of the access point. Use + before international numbers.  
User name Enter your user name if required by the service provider. User names are often case-sensitive and provided  
by your service provider.  
Prompt password — Select Yes to enter your password each time you log into a server or No to save the password in your  
device memory and automate the login.  
Password Enter your password if required by the service provider. The password is often case-sensitive provided by  
the service provider.  
Authentication — Select Secure to always send your password encrypted or Normal to send your password encrypted  
when possible.  
Homepage Enter the Web address of the page you want to display as a home page when you use this access point.  
Data call type — Select Analogue or ISDN.  
Max. data speed — Select the limit to apply to the transfer speed. If you select Automatic, the data transfer rate is  
determined by the network and may be affected by network traffic. Some service providers may charge more for higher  
data rates.  
4. After defining the basic settings, select Options > Advanced settings to define the advanced settings or Back to save the  
settings and exit.  
Advanced Internet access point settings for data calls  
After setting up a basic Internet access point for Data call or High speed data (GSM only), select Options > Advanced settings,  
and define the following advanced settings.  
IPv4 settings Enter the device IP and name server addresses for IPv4 Internet protocol.  
IPv6 settings Enter the device IP and name server addresses for IPv6 Internet protocol.  
Proxy serv. address Enter the proxy server address.  
Proxy port number Enter the proxy server port number. Proxy servers are intermediate servers between a browsing service  
and its users, which are used by some service providers. These servers may provide additional security and speed up access  
to the service.  
Use callback — Select Yes if you have a service that dials back to your device when you establish an Internet connection.  
Copyright © 2006 Nokia. All Rights Reserved.  
43  
           
C o n n e c t i v i t y  
Callback type — Select Use server no. or Use other no., according to instructions from your service provider.  
Callback number Enter your data call phone number of your device, which the callback server uses.  
Use PPP compress. — Select Yes to speed up the data transfer, if it is supported by the remote PPP server.  
Use login script — Select Yes, if your Internet service provider requires a login script, or if you want to automate your login.  
A login script is a sequence of instructions that the system follows during the login process.  
Login script Enter the login script. This setting is available only if you have selected Use login script > Yes.  
Modem initialisation Enter a command string for the connection setup, if required by your service provider.  
Set up an Internet access point for packet data (GPRS)  
1. Select Menu > Tools > Settings > Connection > Access points.  
2. Select Options > New access point. To use an existing access point as a basis for the new one, select Use existing settings. To  
start with an empty access point, select Use default settings.  
3. Define the following settings.  
Connection name Enter a descriptive name for the connection.  
Data bearer — Select Packet data.  
Access point name Enter the name for the access point. The name is usually provided by your service provider or network  
operator.  
User name Enter your user name if required by the service provider. User names are often case-sensitive and provided  
by your service provider.  
Prompt password — Select Yes to enter your password each time you log into a server or No to save the password in your  
device memory and automate the login.  
Password Enter your password if required by the service provider. The password is often case-sensitive provided by  
the service provider.  
Authentication — Select Secure to always send your password encrypted or Normal to send your password encrypted  
when possible.  
Homepage Enter the Web address of the page you want to display as a home page when you use this access point.  
4. After defining the settings, select Options > Advanced settings to define the advanced settings or Back to save the settings  
and exit.  
Advanced Internet access point settings for packet data (GPRS)  
After setting up a basic Internet access point for packet data (GPRS), select Options > Advanced settings, and define the following  
advanced settings.  
Network type — Select IPv4 or IPv6 as the Internet protocol type. The Internet protocol defines how data is transferred to  
and from your device.  
Phone IP address Enter the IP address of your device. Select Automatic to have the network provide the device IP address.  
This setting is shown only if you select Network type > IPv4.  
DNS address Enter the IP addresses of the Primary DNS address and Secondary DNS addr. if required by your service provider  
or network operator. Otherwise, the name server addresses are provided automatically.  
Proxy serv. address Enter the address of the proxy server. Proxy servers are intermediate servers between a browsing  
service and its users, which are used by some service providers. These servers may provide additional security and speed up  
access to the service.  
Set up an Internet access point for wireless LAN  
1. Select Menu > Tools > Settings > Connection > Access points.  
2. Select Options > New access point. To use an existing access point as a basis for the new one, select Use existing settings. To  
start with an empty access point, select Use default settings.  
3. Define the following settings.  
Connection name Enter a descriptive name for the connection.  
Data bearer — Select Wireless LAN.  
WLAN netw. name To enter the service set identifier (SSID), that is, the name that identifies the specific wireless LAN,  
select Enter manually. To select the network from the wireless LANs in range, select Search for netw..  
Network status — Select Hidden if the network you are connecting to is hidden, or Public if it is not hidden.  
WLAN netw. mode — If you select Infrastructure, devices can communicate with each other and with wired LAN devices  
through a wireless LAN access point. If you select Ad-hoc, devices can send and receive data directly with each other, and  
no wireless LAN access point is needed.  
WLAN security mode You must select the same security mode that is used in the wireless LAN access point. If you select  
WEP (wired equivalent privacy), 802.1x, or WPA2 (Wi-Fi protected access), you must also configure the relevant additional  
settings.  
WLAN security sett. Edit the security settings for the selected WLAN security mode.  
Copyright © 2006 Nokia. All Rights Reserved.  
44  
         
C o n n e c t i v i t y  
Homepage Enter the Web address of the page you want to display as a home page when you use this access point.  
The settings available for editing may vary.  
Advanced Internet access point settings for wireless LAN  
Select Menu > Tools > Settings > Connection > Access points.  
After setting up a basic Internet access point for wireless LAN, select Options > Advanced settings, and define the following  
advanced settings.  
IPv4 settings Enter the device IP and name server addresses for the IPv4 Internet protocol.  
IPv6 settings — Select or enter the name server addresses for the IPv6 Internet protocol.  
Ad-hoc channel — If the selected network mode is ad-hoc, select User defined to manually enter a channel number (1-11).  
Proxy serv. address Enter the proxy server address.  
Proxy port number Enter the proxy server port number.  
The settings available for editing may vary. Contact your service provider for more information.  
Cable connection  
Install the USB data cable driver to your PC before you use a cable connection. You can use the Data transfer without installing  
the USB data cable drivers.  
Select Menu > Connect. > Data cbl..  
Using a USB data cable, you can connect your device to a compatible PC . Connect the USB data cable to the bottom of the device.  
To change the device type you normally connect to your device with the data cable, press the joystick.  
Select from the following:  
Ask on connection — Select whether you want to be asked for the device type every time you connect the data cable to your  
device.  
PC Suite Connect the PC Suite to your device with the data cable, and use your device as a modem.  
Data transfer Access and transfer data such as music or image files from your computer using the data cable connection.  
To use the Data transfer mode, make sure that you have not selected USB as a connection type in the Manage connections  
settings in Nokia PC Suite. Insert a memory card to your device, connect the device to a compatible computer with the USB  
data cable, and select Data transfer when the device asks which mode is used. In this mode, your device acts as a mass storage  
device and you can see it as a removable hard drive in your computer. The device will switch into the Offline profile if this is  
selected. End the connection from the PC (for example, from an Unplug or Eject Hardware wizard in Windows) to avoid  
damaging the memory card. After you end the connection, the device returns to the profile in which it was before using the  
data transfer mode.  
IP passthrough — Select an access point through which to transfer data using the Internet protocol.  
To save your selection, select Back.  
IP passthrough  
Select Menu > Connect. > Data cable > Options > Change > IP passthrough.  
The IP passthrough application allows you to obtain a network connection on your device from a compatible PC through a data  
cable.  
Set up a data cable to use IP passthrough  
Use IP passthrough as you use any Internet access point to browse or synchronize remotely. If a wireless network connection  
is unavailable, use IP passthrough to access the Internet or a LAN. You cannot use IP passthrough at the same time as Nokia PC  
Suite. You cannot activate the modem if you select IP passthrough in cable connection settings.  
To prepare for an IP passthrough session, connect a data cable to your device, and select IP passthrough as the connection  
method. Connect the other end of the data cable to a compatible PC, and wait for the PC to recognize your device.  
Access point for IP passthrough  
Menu > Tools > Settings > Connection > Access points.  
To configure IP passthrough basic settings, select Options > New access point > Use default settings. Enter a name for your IP  
passthrough connection in the Connection name field, select IP passthrough in the Data bearer field, and enter an address in  
the Homepage field.  
Advanced IP passthrough access point settings  
Menu > Tools > Settings > Connection > Access points.  
Copyright © 2006 Nokia. All Rights Reserved.  
45  
                   
C o n n e c t i v i t y  
To use advanced settings, open an IP passthrough access point, and select Options > Advanced settings and select from the  
following:  
IPv4 settings Enter the Phone IP address and DNS address for the IPv4 Internet protocol.  
IPv6 settings Enter the DNS address for the IPv6 Internet protocol.  
Proxy serv. address Enter the proxy server address.  
Proxy port number Enter the proxy server port number.  
Bluetooth  
There may be restrictions on using Bluetooth technology in some locations. Check with your local authorities or service provider.  
Features using Bluetooth technology, or allowing such features to run in the background while using other features, increase  
the demand on battery power and reduces the battery life.  
This device is compliant with Bluetooth Specification 1.2 supporting the following profiles: Generic Access Profile, Serial Port  
Profile, Dial-up Networking Profile, Headset Profile, Handsfree Profile, Generic Object Exchange Profile, Object Push Profile, File  
Transfer Profile, SIM Access Profile, and Basic Imaging Profile. To ensure interoperability between other devices supporting  
Bluetooth technology, use Nokia approved enhancements for this model. Check with the manufacturers of other devices to  
determine their compatibility with this device.  
Bluetooth technologyenables wireless connections between electronicdevices within a range of10 meters (33 feet). ABluetooth  
connection can be used to send images, videos, texts, business cards, calendar notes, or to connect wirelessly to devices using  
Bluetooth technology, such as computers.  
Since devices using Bluetooth technology communicate using radio waves, your device and the other devices do not need to  
be in direct line-of-sight. The two devices only need to be within a maximum of 10 meters of each other, although the connection  
can be subject to interference from obstructions such as walls or from other electronic devices.  
Start using Bluetooth  
Select Menu > Connect. > Bluetooth.  
1. When you activate Bluetooth for the first time, you are asked to give a name to your device. Give your device a unique name  
to make it easy to recognize if there are several Bluetooth devices in the vicinity.  
2. Select Bluetooth > On.  
3. Select My phone's visibility > Shown to all.  
Your device and the name you entered can now be seen by other users with devices using Bluetooth technology.  
Settings  
Define the following settings:  
Bluetooth — Select On to be able to connect to another compatible device using Bluetooth connectivity.  
My phone's visibility — Select Shown to all to allow other devices using Bluetooth technology to find your device when you  
have set Bluetooth > On. To prevent other devices from finding your device, select Hidden. Even if you select Hidden, paired  
devices can still detect your device.  
My phone's name Enter a name for your device. The name is visible to other devices that search for devices using Bluetooth  
technology. The maximum length of the name is 30 characters.  
Remote SIM mode — Select On to enable another device, such as a compatible car kit enhancement, to use the SIM card in  
your device to connect to the network. See "SIM access profile," p. 48.  
If Bluetooth was turned off as a result of entering Offline profile, you must re-enable Bluetooth manually.  
Security tips  
When you are not using Bluetooth connectivity, select Bluetooth > Off or My phone's visibility > Hidden.  
Do not pair with an unknown device.  
Send data  
Several Bluetooth connections can be active at a time. For example, if you are connected to a headset, you can also transfer files  
to another compatible device at the same time.  
1. Open the application where the item you want to send is stored.  
2. Select the item, and select Options > Send > Via Bluetooth. The device searches for other devices using Bluetooth technology  
within range and lists them.  
Tip: If you have sent data using Bluetooth before, a list of the previous search results is displayed. To search for  
more Bluetooth devices, select More devices.  
Copyright © 2006 Nokia. All Rights Reserved.  
46  
             
C o n n e c t i v i t y  
3. Select the device with which you want to connect, and press the joystick to set up the connection. If the other device requires  
pairing before data can be transmitted, you are asked to enter a passcode.  
4. When the connection has been established, Sending data is shown.  
The Sent folder in Messag. does not store messages sent using Bluetooth connectivity.  
If you have sent items using Bluetooth before, a list of the previous search results is displayed. To search for more Bluetooth  
devices, select More devices.  
To use a Bluetooth audio enhancement such as Bluetooth handsfree or headset you need to pair your device with the  
enhancement. See the enhancement user guide for the passcode and further instructions. To connect to the audio enhancement,  
press the power key to turn on the enhancement. Some audio enhancements connect automatically to your device. Otherwise  
open Paired devices, scroll to the enhancement, and select Options > Connect.  
Bluetooth connectivity indicators  
Bluetooth is active.  
When the icon is blinking, your device is trying to connect to the other device. When the icon is shown continuously, the  
Bluetooth connection is active.  
Pair devices  
Select Menu > Connect. > Bluetooth, and scroll right to open the Paired devices page.  
Before pairing, create your own passcode (1-16 digits), and agree with the user of the other device to use the same code. Devices  
that do not have a user interface have a fixed passcode. You need the passcode only when you connect the devices for the first  
time. After pairing, it is possible to authorize the connection. See "Authorize a device," p. 47. Pairing and authorizing the  
connection makes connecting quicker and easier, as you do not have to accept a connection between paired devices every time  
you establish the connection.  
The passcode for remote SIM access must have 16 digits.  
1. Select Options > New paired device. The device starts to search for Bluetooth devices within range.  
Tip: If you have sent data using Bluetooth before, a list of the previous search results is displayed. To search for  
more Bluetooth devices, select More devices.  
2. Select the device with which you want to pair, and enter the passcode. The same passcode must be entered to the other  
device as well.  
3. Select Yes to make the connection between your device and the other device automatic or No to confirm the connection  
manually every time a connection attempt is made. After pairing, the device is saved to the paired devices page.  
To give a nickname to a paired device that is only displayed in your device, scroll to the device with which you have paired, and  
select Options > Assign short name.  
To delete a pairing, select the device whose pairing you want to delete and Options > Delete. To delete all pairings, select  
Options > Delete all.  
Tip: If you are currently connected to a device and cancel the pairing with that device, pairing is removed immediately,  
and the connection is switched off.  
Authorize a device  
If you trust a paired device, you can allow it to connect automatically to your device. You can select from the following options:  
Set as authorised Connections between your device and the other device can be made without your knowledge. No separate  
acceptance or authorization is needed. Use this status for your own devices, such as your compatible headset or PC, or devices  
that belong to someone you trust.  
Set as unauthorised Connection requests from the other device must be accepted separately every time.  
Receive data  
If you want to receive data using Bluetooth, select Bluetooth > On and My phone's visibility > Shown to all. When you receive  
data through Bluetooth connectivity, a tone sounds, and you are asked if you want to accept the message. If you accept, the  
message is placed in the Inbox folder in Messag.  
Tip: You can access the files in the device or on the memory card using a compatible accessory that supports the File  
Transfer Profile Client service (for example, a laptop computer).  
End a Bluetooth connection  
A Bluetooth connection is disconnected automatically after sending or receiving data. Only Nokia PC Suite and some  
enhancements such as headsets may maintain a connection even if not actively used.  
Copyright © 2006 Nokia. All Rights Reserved.  
47  
           
C o n n e c t i v i t y  
SIM access profile  
When the wireless device is in the remote SIM mode, you can only use a compatible connected enhancement, such as a car kit,  
to make or receive calls. Your wireless device will not make any calls, except to the emergency numbers programmed into your  
device, while in this mode. To make calls from your device, you must first leave the remote SIM mode. If the device has been  
locked, enter the code to unlock it first.  
With the SIM access profile, you can access the SIM card of your device from a compatible car kit device. This way, you do not  
need a separate SIM card to access SIM card data and connect to the GSM network.  
To use the SIM access profile, you need the following:  
Compatible car kit device that supports Bluetooth wireless technology  
Valid SIM card in your device  
Manage the SIM access profile  
1. Select Menu > Connect. > Bluetooth to activate Bluetooth connectivity in your device.  
2. To enable remote SIM access, scroll to Remote SIM mode, and press the joystick.  
3. Activate Bluetooth in the car kit device.  
4. Use your car kit device to start a search for compatible devices. For instructions, see the user guide of your car kit device.  
5. Select your device from the list of compatible devices.  
6. To pair the devices, enter the Bluetooth passcode shown on the display of the car kit device to your device.  
7. Authorize the car kit device. Select Menu > Connect. > Bluetooth, and scroll to the Paired devices page. Scroll to the car kit  
device, and enter the Bluetooth passcode. When the device asks to make the connection automatic, select Yes. Connections  
between your device and the car kit device can be made without separate acceptance or authorization. If you select No,  
connection requests from this device must be accepted separately every time.  
Tip: If you have already accessed the SIM card from the car kit with the active user profile, the car kit searches  
automatically for a device with the SIM card. If it finds your device, and automatic authorization is activated, the car  
device automatically connects to the GSM network when you switch on the car ignition.  
When you activate the remote SIM access profile, you can use applications on your device that do not need network or SIM  
services.  
To end the remote SIM access connection from your device, select Menu > Connect. > Bluetooth > Remote SIM mode > Off.  
Infrared  
Do not point the IR (infrared) beam at anyone's eye or allow it to interfere with other IR devices. This device is a Class 1 laser  
product.  
Use infrared to connect two devices and transfer data between them. With infrared, you can transfer data such as business  
cards, calendar notes, and media files with a compatible device.  
Send and receive data  
1. Ensure that the infrared ports of the devices face each other. The positioning of the devices is more important than angle or  
distance.  
2. Select Menu > Connect. > Infrared, and press the joystick to turn on infrared on your device. Turn on infrared on the other  
device.  
3. Wait a few seconds until an infrared connection is established.  
4. To send, locate the desired file in an application or the file manager, and select Options > Send > Via infrared.  
If data transfer is not started within 1 minute after the activation of the infrared port, the connection is cancelled and must be  
started again.  
All items received through infrared are placed in the Inbox folder in Messag..  
Positioning devices away from each other breaks a connection, but the infrared light beam remains active on your device until  
it is deactivated.  
Data connections  
Packet data  
GPRS (general packet radio service) enables wireless access for mobile phones to data networks (network service). GPRS uses  
packet data technology where information is sent in short bursts of data over the mobile network. The benefit of sending data  
Copyright © 2006 Nokia. All Rights Reserved.  
48  
               
C o n n e c t i v i t y  
in packets is that the network is occupied only when sending or receiving data. As GPRS uses the network efficiently, it allows  
for quick data connection set-up and fast data transmission speeds.  
You must subscribe to the GPRS service. For availability and subscription to GPRS, contact your network operator or service  
provider.  
Enhanced GPRS (EGPRS) is similar to GPRS, but it enables faster connection. For more information on the availability of EGPRS  
and data transfer speed, contact your network operator or service provider. Note that when you have selected GPRS as a data  
bearer, the device uses EGPRS instead of GPRS if this is available in the network.  
During a voice call, you cannot establish a GPRS connection, and any existing GPRS connection is put on hold unless the network  
supports dual transfer mode.  
UMTS  
UMTS (universal mobile telecommunications system) is 3G mobile communication system. Besides voice and data, UMTS enables  
audio and video delivery to wireless devices.  
Your device can automatically switch between the GSM and UMTS networks.  
To select which network to use, select Menu > Tools > Settings > Network and the network in Network mode. If you want the  
device to switch between the networks automatically, select Dual mode.  
The GSM network is indicated with , the UMTS network with  
.
When you use your device in GSM and UMTS networks, multiple data connections can be active at the same time, and access  
points can share a data connection. In the UMTS network, data connections remain active during voice calls. You can, for example,  
surf the Web faster than previously possible while simultaneously speaking on the phone.  
Wireless local area network (WLAN)  
Some places, like France, have restrictions on the use of wireless LAN. Check with your local authorities for more information.  
Features using wireless LAN, or allowing such features to run in the background while using other features, increase the demand  
on battery power and reduce the battery life.  
This device can detect and connect to a wireless local area network.  
If you move the device to another location within the wireless LAN and out of range of a wireless LAN access point, the roaming  
functionality can automatically connect your device to another access point that belongs to the same network. As long as you  
remain within range of access points that belong to the same network, your device can stay connected to the network.  
Tip: A wireless LAN connection is established when you create a data connection using a wireless LAN Internet access  
point. The active wireless LAN connection is ended when you end the data connection.  
Your device enables different types of communication in a wireless LAN. The two operating modes are infrastructure and ad  
hoc.  
The infrastructure operating mode allows two kinds of communication: wireless devices communicate with each other  
through a wireless LAN access point or wireless devices communicate with a wired LAN device through a wireless LAN access  
point. The advantage of the infrastructure operating mode is that you can have more control over network connections  
because they pass through an access point. A wireless device can access the services that are available in a regular wired LAN:  
company database, e-mail, the Internet, and other network resources, for example.  
In the ad hoc operating mode you can send data to and receive it from other devices with compatible wireless LAN support ,  
for example, to be printed. These functions may require an additional third party application to work. No wireless LAN access  
point is required. Simply make the necessary configurations and start communicating. Ad hoc networking is easy to set up,  
but communication is limited to devices that are within range and support compatible wireless LAN technology.  
If you need to configure the MAC address of your device to a WLAN router, enter *#62209526# on the device keypad. The MAC  
address is shown on the device display.  
Connection manager  
Select Menu > Connect. > Conn. mgr..  
To view the status of data connections or end connections, select Act. data conn..  
To search for wireless LANs available within range, select Availab. WLAN.  
View and end active connections  
Note: The actual time invoiced for calls by your service provider may vary, depending on network features, rounding  
off for billing, and so forth.  
In the active connections view, you can see the open data connections: data calls, packet data connections, and wireless LAN  
connections.  
Copyright © 2006 Nokia. All Rights Reserved.  
49  
               
C o n n e c t i v i t y  
To view detailed information about network connections, select the connection from the list and Options > Details. The type of  
information shown depends on the connection type.  
To end a network connection, select the connection from the list and Options > Disconnect.  
To end all active network connections simultaneously, select Options > Disconnect all.  
To view the details of a network, press the joystick.  
Search for wireless LAN  
To search for wireless LANs available within range, select Menu > Connect. > Conn. mgr. > Availab. WLAN. A list of found networks  
is displayed.  
The available wireless LAN view shows a list of wireless LANs within range, their network mode (infrastructure or ad-hoc), signal  
strength indicator and network encryption indicators, and if your device has an active connection with the network.  
To view the details of a network, press the joystick.  
To create an Internet access point in a network, select Options > Define access point.  
Modem  
Select Menu > Connect. > Modem.  
Together with a compatible computer, you can use your device as a modem to connect to the Web.  
Before you can use your device as a modem  
You need the appropriate data communications software on your computer.  
You must subscribe to the appropriate network services from your service provider or Internet service provider.  
You must have the appropriate drivers installed on your computer. You must install drivers for your cable connection, and  
you may need to install or update Bluetooth or infrared drivers.  
To connect the device to a compatible computer using infrared, press the joystick. Make sure the infrared ports of the device  
and computer are directly facing each other with no obstacles between them.  
To connect your device to a computer using Bluetooth wireless technology, initiate the connection from the computer. To  
activate Bluetooth in your device, select Menu > Connect. > Bluetooth and select Bluetooth > On.  
If you use a cable to connect your device to a computer, initiate the connection from the computer.  
Note that you may not be able to use some of the other communication features when the device is used as a modem.  
Mobile VPN  
Select Menu > Tools > Settings > Connection > VPN.  
The Nokia mobile virtual private network (VPN) client creates a secure connection to compatible corporate Intranet and services,  
such as e-mail. Your device connects from a mobile network, through the Internet, to a corporate VPN gateway that acts as a  
front door to the compatible corporate network. VPN client uses IP Security (IPSec) technology. IPSec is a framework of open  
standards for supporting secure exchange of data over IP networks.  
VPN policies define the method used by VPN client and a VPN gateway to authenticate each other, and the encryption algorithms  
that they use to help protect the confidentiality of data. Contact your corporation for a VPN policy.  
To use VPN with an application, the application must be associated with a VPN access point. A VPN access point is made up of  
an Internet access point and a VPN policy.  
VPN management  
You can manage your VPN policies, policy servers, VPN logs, and key store password in VPN management. VPN policies define  
how data is encrypted for transfer over unsecured networks. The key store password helps protect private keys.  
An access point is where your device connects to the network by way of a data call or packet data connection. To use e-mail  
and multimedia services or to browse Web pages, you must first define Internet access points for these services. VPN access  
points pair VPN policies with Internet access points to create encrypted connections.  
To manage VPN, select VPN management > Options > Open and from the following options:  
VPN policy — Install, view, and update VPN policies.  
VPN policy servers Edit the connection settings of VPN policy servers from which you can install and update VPN policies.  
VPN log View the log for your VPN policy installations, updates and synchronizations, and other VPN connections.  
Manage VPN policies  
To manage VPN policies, select VPN management > VPN policy > Options and from the following options:  
Copyright © 2006 Nokia. All Rights Reserved.  
50  
             
C o n n e c t i v i t y  
Install policy — Install a policy. Enter your user name and password for the VPN policy server. Contact your system  
administrator for your user name and passwords.  
Define VPN ac. point Create a VPN access point that pairs a VPN policy with an Internet access point.  
Update policy Update the selected VPN policy.  
Delete policy Delete the selected VPN policy. If you delete a VPN policy, it is reinstalled when you synchronize your device  
with the VPN policy server the next time unless it has also been deleted from the server. Similarly, if a VPN policy has been  
deleted from the server, it is deleted also from your device upon synchronization.  
To manage VPN policy servers, select VPN policy servers > Options > Open and from the following options:  
New server Add a VPN policy server.  
Synchronise server — Install new or update the selected VPN policy.  
Delete server Delete the selected VPN policy server.  
To manage VPN policy server settings, select Options > Open > New server or Edit server and from the following options:  
Policy server name Enter a new name for the server, up to 30 characters.  
Policy server addr. Enter the server address. The policy server address cannot be edited after you connect to the server to  
install or update VPN policies.  
Internet access pt. — Select the Internet access point to connect to the VPN policy server.  
Key store password Change the password of the private key store. The password is created automatically when it is needed  
for the first time.  
View the VPN log  
Select VPN management > VPN log > Open.  
A VPN log records your visits to VPN servers to install, update, and synchronize VPN policies and your VPN connections. Error,  
warning, and information entries are indicated by an icon on the left-hand side of the entry. To view a log entry in detail, select  
it. Report the reason codes visible in the detailed view to your system administrators as the codes help to look for causes of  
possible problems you may have with VPN. When the log size reaches 20 KB, the oldest log entries are deleted to make space  
for new entries.  
Select Options and from the following options:  
Refresh log Update the log.  
Clear log Delete the log entries.  
Email data roaming  
Select Menu > Tools > Settings > Connection > Access point groups.  
Your device allows roaming between wireless access technologies, such as WLAN and GPRS, for e-mail. For example, you can  
start an e-mail session at home and continue the session on your way to work. While your session continues uninterrupted,  
your handheld device switches from WLAN to GPRS and back to WLAN when you arrive at your workplace.  
Access point groups  
1. To create an access point group, select Access point groups > Options > New group.  
2. In the Group name field, enter a name for the group.  
3. Define in the Conn. switching field whether to show the connection switching process on the display of your device.  
4. Choose and edit the access points that belong to this group in the Access points section.  
To add an access point to the selected access point group, select Access points > Options > Add access point, and select the  
access point to add.  
To edit an access point in an access point group, select the access point and Options > Edit.  
To remove an access point in an access point group, select the access point and Options > Remove.  
To set the order in which access points are used for email data roaming, select an access point group and Change. Scroll to an  
access point, and select Options > Raise priority or Lower priority.  
To change the STMP settings of an access point, select the desired access point from the access point group list, select  
Options, and select from the following:  
Override SMTP serv. Override the current STMP server settings.  
SMTP server Edit the server name or the server IP address.  
Secure connection — Select whether to use secure connection.  
Use authentication — Select whether to use authentication.  
User name Edit your user name for the STMP server.  
Password Edit your password for the STMP server.  
Copyright © 2006 Nokia. All Rights Reserved.  
51  
         
C o n n e c t i v i t y  
Configure access point groups for mail and synchronization  
To set an access point group for mail, select Menu > Messaging > Mailbox > E-mail settings > Connection settings > Incoming  
e-mail > Access point in use > Options > Change, and select the desired access point group.  
To set an access point group for synchronization, select Menu > Connect. > Sync > Profile > Options > Edit > Connection  
settings > Access point > Change, and select the desired access point group.  
Copyright © 2006 Nokia. All Rights Reserved.  
52  
 
7.  
Web  
Select Menu > Web (network service).  
Web is one of the two browsers in your device. With Web, you can browse regular Web sites. These pages use the extensible  
hypertext markup language (XHTML) or hypertext markup language (HTML). If you want to browse WAP pages, use Menu >  
Media > Services. Both of the browsers use the same bookmarks. The links in your received messages open in the Services  
browser.  
Check the availability of services, pricing, and fees with your network operator or service provider. Service providers will also  
give you instructions on how to use their services.  
Access points  
To browse the Web, you need to configure Internet access point settings. If you are using a data call or a GPRS connection, your  
wireless network must support data calls or GPRS, and the data service must be activated for your SIM card. Your device might  
have configured the Internet access point settings automatically based on your SIM card. If not, contact your service provider  
for the correct settings.  
Tip: You may receive the Internet access point settings from your service provider as a special text message or from  
the network operator's or service provider's Web pages.  
You can also enter the Internet access point settings manually. See "Internet access points," p. 43.  
Browse the Web  
Use the joystick for browsing. The joystick is shown as a pointer on a Web page, and you can scroll the pages up, down, left and  
right with it. When you move the pointer over a link, the pointer changes into a hand. Press the joystick to open the link.  
To browse the Web, select a bookmark, and press the joystick. You can also enter the Web address, and press the joystick. Use  
only services that you trust and that offer adequate security and protection against harmful software.  
Tip: When you start to enter the address, addresses of pages you have previously visited that match your input are  
displayed. To open a page, scroll to the address, and press the joystick.  
To open a Web link, scroll to it and press the joystick. On a Web page, new links appear underlined in blue and previously visited  
links in purple. Images that act as links have a blue border around them.  
Addresses of the pages you visit are saved in the Auto. bookmarks folder.  
Keyboard shortcuts:  
Press 1 to open your Bookmarks.  
press 2 to find text.  
Press 3 to return to the previous page.  
Press 5 to switch between your open browser windows.  
Press 8 to open page overview.  
Press 9 to go to a different Web page.  
Bookmarks  
Your device may have some bookmarks loaded for sites not affiliated with Nokia. Nokia does not warrant or endorse these sites.  
If you choose to access them, you should take the same precautions, for security or content, as you would with any Internet  
site.  
To view a bookmarked Web page, scroll to the bookmark, and press the joystick.  
To browse another Web pages, select Options > Navigation options > Go to web address, enter the page address, and select Go  
to.  
To delete a bookmark, scroll to it, and press the clear key.  
To add a bookmark, select Menu > Web > Options > Bookmark manager > Add bookmark. Scroll to Name to enter a descriptive  
name for the bookmark, Address to enter the Web page address, Access point to change the access point to connect to the Web  
page, and User name or Password to enter your user name and password, if required by the service provider. To save the  
bookmark, select Back.  
Download items  
Important: Only install and use applications and other software from sources that offer adequate security and  
protection against harmful software.  
Copyright © 2006 Nokia. All Rights Reserved.  
53  
             
W e b  
You can download different items such as ringing tones, images, operator logos, themes, and video clips. To download an item,  
scroll to it, and press the joystick. These items can be provided free, or you can purchase them. Downloaded items are handled  
by the respective applications in your device.  
When you start a download, a list of ongoing, paused, and completed downloads from the current browsing session is displayed.  
To view the list, you can also select Options > Tools > Downloads. In the list, scroll to an item, and select Options to pause,  
resume, or cancel ongoing downloads; or open, save, or delete completed downloads.  
To purchase items:  
1. To download the item, scroll to the link, and press the joystick.  
2. Select the appropriate option to purchase the item.  
3. Carefully read all the information provided. To continue the download, select Accept. To cancel the download, select  
Cancel.  
End a connection  
To end the connection and view the browser page offline, select Options > Advanced options > Disconnect; or to end the  
connection and close the browser, select Options > Exit.  
Clear the cache  
A cache is a memory location that is used to store data temporarily. If you have tried to access or have accessed confidential  
information requiring passwords, empty the cache after each use. The information or services you have accessed are stored in  
the cache.  
To clear the cache, select Options > Advanced options > Clear cache.  
News feeds and blogs  
Select Menu > Web > Web feeds.  
Feeds usually contain headlines and articles, often about recent news or other topics.  
Tip: Blog is a shortening of Weblog, which is a continuously updated Web diary . Often the author's personality is an  
important factor in the blog.  
To download a feed or blog, scroll to it, and press the joystick.  
To add a feed or blog, select Options > Manage feed > New feed, and enter the information.  
To edit a feed or blog, scroll to a feed, select Options > Manage feed > Edit, and modify the information.  
Web settings  
Select Menu > Web > Options > Settings.  
Define the following settings:  
Access point — Scroll to the access point to connect to Web pages, and press the joystick.  
Load imgs. & sounds — Select No to load pages faster when browsing by not loading the images on them.  
Font size — Select the font size that you want to use when viewing the Web pages.  
Default encoding — Select the correct character encoding for your language.  
Auto. bookmarks — Select On to save Web page addresses that you visit automatically in the Auto. bookmarks folder. To hide  
the folder, select Hide folder.  
Screen size — Select Full screen to use the whole display area for viewing Web pages. You can press the left selection key to  
open Options and use the available options while browsing in full screen mode.  
Homepage — Select the page that you want to appear as your homepage. Select Default to use the access point homepage,  
User defined to enter the homepage address, or Use current page to use the currently open Web page.  
Mini map — Select whether you want to see an overview of the page as a miniature on top of the page you are viewing.  
History list — Select whether you want to see miniatures of the pages you have visited when you want to go back in your  
browsing history.  
Cookies — Select to allow or reject the sending and receiving of cookies. Cookies are info the network server collects about  
your visits to various Web pages. They are necessary if you shop on the Web (for example, to retain the items you buy until  
you reach the cashier page). However, the information may be misused (for example, you may receive unwanted  
advertisements in your device).  
Java/ECMA script — Some Web pages may include program commands that affect the appearance of the page or interaction  
between the page and its browsers. To deny the use of such scripts, select Disabled (for example, if you have trouble  
downloading).  
Security warnings — Select Show or Hide to see or hide the security warnings you may receive during browsing.  
Copyright © 2006 Nokia. All Rights Reserved.  
54  
           
W e b  
Block pop-ups — Select whether you want to allow pop-ups. Some pop-ups may be necessary (for example, smaller windows  
where you write e-mails in Web-based mail systems), but they may also contain unwanted advertising.  
Services  
Select Menu > Media > Services (network service).  
Services is one of the two browsers in your device. With Services, you can browse WAP pages that have been designed specially  
for mobile devices. For example, operators may have WAP pages for mobile devices. To browse regular Web pages, use the other  
browser in Menu > Web.  
Check the availability of services, pricing, and fees with your network operator or service provider. Service providers will also  
give you instructions on how to use their services.  
Tip: To start a connection, press and hold 0 in the standby mode.  
Copyright © 2006 Nokia. All Rights Reserved.  
55  
   
8.  
Media applications  
Copyright protections may prevent some images, music (including ringing tones), and other content from being copied,  
modified, transferred or forwarded.  
Select Menu > Media.  
Media contains different media applications that allow you to save and view images, record sounds, and play sound clips.  
Gallery  
Select Menu > Media > Gallery.  
Use Gallery to access and use different types of media, including images, videos, music, and sounds. All viewed images and  
videos and all received music and sounds are automatically saved to Gallery. You can browse, open, and create folders; and  
mark, copy, and move items to folders. Sound clips are opened in the Music Player, and video clips and streaming links in the  
RealPlayer application.  
To open a file or a folder, press the joystick. Images are opened in the image viewer.  
To create a new folder, select Options > Organise > New folder.  
To copy or move files, select a file and Options > Organise > Move to folder, New folder, Move to memory card, Copy to memory  
card, Copy to phone mem., or Move to phone mem..  
To download files into the Gallery in one of the main folders using the browser, select Graphic downl., Video downl., Track  
downl., or Sound downl.. The browser opens, and you can choose a bookmark or enter the address for the site to download  
from.  
To search for a file, select Options > Find. Start to enter a search string (for example, the name or date of the file you are searching  
for). Files that match the search are shown.  
Images  
Select Menu > Media > Gallery > Images.  
Images consists of two views:  
In the image browser view you can send, organize, delete, and rename images stored in your device or memory card. You  
can set images as wallpaper for your display.  
In the image viewer, which opens when you select an image in the image browser view, you can view, and send individual  
images.  
The following file formats are supported: JPEG, BMP, PNG, and GIF 87a/89a. The device does not necessarily support all variations  
of the file formats.  
To open an image for viewing, select an image in the image browser view, and select Options > Open. The image opens in the  
image viewer.  
To open the next or previous image for viewing, scroll right or left in the image viewer.  
To enlarge the viewed image on the display, select Options > Zoom in, or press 5 or 7. To reduce the viewed image on the display,  
select Zoom out or press 0.  
To view the image in full screen size, select Options > Full screen or press 7 twice. To return to normal view, select Options >  
Normal screen.  
To rotate an image, select an image, and Options > Rotate. Select Right to rotate the image clockwise by 90 degrees, or select  
Left to rotate the image counterclockwise by 90 degrees.  
Manage image files  
Copyright protections may prevent some images, ringing tones, and other content from being copied, modified, transferred or  
forwarded.  
To view detailed information about an image, select an image and Options > View details. Size and format of the file, the time  
and date the file was last modified and the resolution of the image in pixels are displayed.  
To send an image, select the image, Options > Send, and the method for sending.  
To rename an image, select an image and Options > Rename. Enter a new name, and select OK.  
To set an image as wallpaper, select the image and Options > Set as wallpaper.  
To add an image to a contact card, select an image and Options > Assign to contact. The contacts view opens, and you can select  
the contact for the image.  
Copyright © 2006 Nokia. All Rights Reserved.  
56  
               
M e d i a a p p l i c a t i o n s  
Organizing images  
To create folders to organize your images, select Options > Organise > New folder. Enter a name for the folder, and select OK.  
To move an image to another folder, select the image and Options > Organise > Move to folder. Scroll to the folder to which you  
want to move the image, and select Move.  
RealPlayer  
Copyright protections may prevent some images, ringing tones, and other content from being copied, modified, transferred or  
forwarded.  
Select Menu > Media > RealPlayer.  
RealPlayer can play video clips and audio files that are stored in the device memory or on a memory card, transferred to your  
device from e-mail or compatible PC, or streamed to your device over the Web.  
Formats supported by RealPlayer include MPEG-4, MP4 (not streaming), 3GP, RV, RA, AAC, AMR, and Midi.RealPlayer does not  
necessarily support all variations of a media file format.  
Tip: Streaming audio and video files means playing them directly from the Web without downloading them first to  
your device.  
Play video clips and stream links  
To select audio and video files to play with RealPlayer, select Options > Open, and scroll to a media clip in your device or on a  
memory card.  
To play streaming media, select a Web link that points to a media clip, and select Play; or connect to the Web, browse to a video  
clip or audio file, and select Play. RealPlayer recognizes two kinds of links: an rtsp:// URL and an http:// URL that points to a RAM  
file. Before the content begins streaming, your device must connect to a Web site and buffer the content. If a network connection  
problem causes a playback error, RealPlayer attempts automatically to reconnect to the Internet access point.  
To play audio and video files stored in your device or on a memory card, select the file and Play.  
To stop playback or streaming, select Stop. Buffering or connecting to a streaming site stops, playback of a clip stops, and the  
clip rewinds to the beginning.  
To view the video clip in full-screen size, select Options > Play in full screen. The size of the video area changes to normal or full  
screen. Full screen increases the size of the video to cover the maximum video area possible while the aspect ratio is maintained.  
To save a media clip, select Options > Save, scroll to a folder in device memory or on a memory card, and select Save. To save a  
link to a media file on the Web, select Save link.  
To fast-forward or rewind the clip during playback, scroll up or down.  
Tip: To fast-forward during play, scroll up and hold. To rewind during play, scroll down and hold.  
To increase or decrease the volume during playback, scroll right or left.  
Send audio files and video clips  
You can transfer a media clip to another device or attach a media clip to a multimedia message, document, or slide presentation.  
To transfer a media clip through infrared or Bluetooth connection, select a clip and Options > Send. Select a method to use to  
send the clip to another device.  
To send a media clip inside a message, create a multimedia message, select a clip to attach and Insert object > Video clip or  
Sound clip.  
To remove a media clip you inserted, select Options > Remove > Yes.  
Receive videos  
Select Menu > Messaging. Open a message that contains a video clip. Scroll to the clip, and press the joystick.  
Select Pause or Stop, select Options, and:  
Play — Play the clip from the start.  
Play in full screen — Play the clip in full screen mode. Landscape style clips will be rotated by 90 degrees. To switch back to  
normal view, press any key.  
Continue Resume playing the clip.  
Continue in full scr. Continue playing the clip in full screen mode.  
Mute Mute the sound of the video clip. To turn sound back on, scroll right.  
Save link — Save the Web link to a clip.  
Copyright © 2006 Nokia. All Rights Reserved.  
57  
             
M e d i a a p p l i c a t i o n s  
Clip details View information such as the clip duration and size.  
Settings Change video or connection settings.  
The available options may vary.  
View information about a media clip  
To view the properties of a video clip, audio file, or Web link, select the clip, and select Options > Clip details. Information may  
include the bit rate or the Internet link of a streaming file.  
To turn on file protection, select a media clip, and Options > Clip details > Status > Options > Change. File protection prevents  
others from changing a file.  
Settings  
Select Menu > Media > RealPlayer > Options > Settings.  
Video settings  
Select Video > Loop > On, if you want to replay video clips automatically after they finish playing.  
Connection settings  
Select Connection, scroll to the following settings, and press the joystick to edit:  
Proxy — Select whether to use a proxy server and to key in the proxy server's IP address and port number.  
Network Change the access point to connect to the Internet and to set the port range used when connecting.  
Proxy settings  
Proxy servers are intermediate servers between media servers and their users. Some service providers use them for additional  
security or to speed up access to Web pages that contain media files.  
Contact your service provider for the correct settings.  
Select Connection > Proxy, scroll to the following settings, and press the joystick to edit:  
Use proxy — Select Yes to use a proxy server.  
Proxy serv. address Enter the IP address of the proxy server. This setting is only available if you select to use a proxy server.  
Proxy port number Enter the port number of the proxy server. This setting is only available if you select to use a proxy  
server.  
Network settings  
Contact your service provider for the correct settings.  
Select Connection > Network, scroll to the following settings, and press the joystick to edit:  
Default access point — Scroll to the access point to connect to the Internet, and press the joystick.  
Online time — Set the time when RealPlayer disconnects from the network when you pause a media clip that plays using a  
network link. Select User defined, and press the joystick. Enter the time, and select OK.  
Lowest UDP port Enter the lowest port number of the server port range. The minimum value is 1024.  
Highest UDP port Enter the highest port number of the server port range. The maximum value is 65535.  
Advanced network settings  
To edit the bandwidth values for different networks, select Connection > Network > Options > Advanced settings.  
To select the bandwidth for any of the listed networks, scroll to its setting, and press the joystick. Scroll to the desired value,  
and select OK.  
To enter the bandwidth yourself, select User defined.  
Contact your service provider for the correct settings.  
To save settings, select Back.  
Music player  
Warning: Do not hold the device near your ear when the loudspeaker is in use, because the volume may be extremely  
loud.  
Select Menu > Media > Music player.  
With the music player, you can play music files, create and listen to track lists, and download music. The music player supports  
files with extensions such as MP3 and AAC.  
Listen to music  
Warning: Listen to music at a moderate level. Continuous exposure to high volume may damage your hearing.  
Copyright © 2006 Nokia. All Rights Reserved.  
58  
                     
M e d i a a p p l i c a t i o n s  
To select a music track, select Options > Music library. All tracks lists all music on your device. To view sorted songs, select  
Albums, Artists, Genres, or Composers. To play a track, scroll to the track, and select Options > Play. When a track is playing, to  
change between play and pause, press and . To stop a track, press  
.
After you add or remove music files in the device, update your Music library. Select Options > Update Music library. The player  
searches the device memory for music files and updates them to the Music library.  
To select the previous or next track, scroll the joystick up or down.  
To play the music tracks repeatedly, select Options > Loop. Select All to repeat all the tracks in the current folder, One to repeat  
the selected track, or Off to set off the repeating.  
To play music in random order, select a folder and Options > Random play.  
To view music track information, scroll to the desired track and select Options > View details.  
Adjust music volume  
To control the music volume, scroll left or right. To mute the volume, scroll left until the volume is muted.  
Track lists  
You can create a new track list and add tracks to it, or select a saved track list.  
To create a new track list, select Options > Music library > Track lists > Options > New track list. Write the name of the new track  
list, and select OK.  
To add a track to a track list, open the track list, and select Options > Add tracks.  
Equalizer  
Select Menu > Media > Music player > Options > Equaliser.  
You can personalize the sound of your music files with Equaliser. You can use preset frequency settings based on styles of music,  
like classical or rock. You can also create customized settings based on your own listening preferences.  
You cannot use other functions of Music player while Equaliser is open.  
With Equaliser, you can enhance or diminish frequencies during music playback and modify how your music sounds. There are  
preset frequency settings in your device, for example Rock.  
To use a preset frequency setting when playing music, scroll to the frequency setting you want to use, and select Options >  
Activate.  
Create your own frequency setting  
1. To create your own frequency setting, select Options > New preset.  
2. Enter a name for the preset frequency setting, and select OK.  
3. Scroll up or down to move between the frequency bands and set the frequency on each band. To move between bands, scroll  
left or right.  
4. Select Back to save the new frequency setting or select Options > Reset to defaults to set the bands at a neutral frequency  
and start over.  
To edit a preset frequency setting, select Options > New preset or Options > Edit.  
To modify the frequency of a preset setting, scroll to the frequency bands, and scroll up or down to increase or decrease their  
values. You hear your frequency adjustment immediately in the playback.  
To reset the frequency bands to their original values, select Options > Reset to defaults.  
To save your new or edited settings, select Back.  
Voice recorder  
Select Menu > Media > Recorder.  
With Recorder, you can record up to 60 seconds of a voice memo, save the voice recording as a sound clip, and play the sound  
clip. Recorder supports the AMR format.  
Press the voice key to activate Recorder. If you have logged in to push to talk, the voice key works as a push to talk key and does  
not activate Recorder.  
To record a voice memo, select Options > Record sound clip. Select Pause to pause the recording and Record to resume recording .  
When you finish recording, select Stop. The sound clip is automatically saved.  
The maximum length of a voice recording is 60 seconds, but it also depends on the storage space available in device memory  
or on a memory card.  
Copyright © 2006 Nokia. All Rights Reserved.  
59  
                 
M e d i a a p p l i c a t i o n s  
Play a voice recording  
To listen to a voice recording that you just recorded, select the play icon ( ). Select Stop to cancel playback. The progress bar  
displays the playing time, position, and length of a voice recording.  
To pause playback of a voice recording, select Pause. Playback resumes when you select Play.  
Voice recordings that you receive or record are temporary files. You must save the files that you want to keep.  
Flash player  
Select Menu > Media > Flash Player.  
With Flash Player, you can view, play, and interact with flash files made for mobile devices.  
The flash files originally designed for the portrait mode may not fully support the landscape mode of your device. For example,  
the command text may be on the bottom of the display and not directly next to the selection keys.  
To open a folder or play a flash file, scroll to the folder or file, and press the joystick.  
To send a flash file to compatible devices, scroll to it, and press the call key. Copyright protection may prevent the sending of  
some flash files.  
To switch between flash files saved on your device memory or memory card, scroll left or right.  
The available options may vary.  
Copyright © 2006 Nokia. All Rights Reserved.  
60  
       
9.  
Camera  
When taking and using images or video clips, obey all laws, and respect local customs as well as privacy and legitimate rights  
of others.  
You can take photos or record video clips with the built-in camera. The camera lens is on the back of the device, and the display  
works as a viewfinder. The camera produces pictures in .jpeg format and video clips in .3gpp format.  
Take a picture  
1. Select Menu > Media > Camera.  
The Nokia E70 device supports an image capture resolution of up to 1600 x 1200 pixels. The image resolution in these  
materials may appear different.  
2. Use the display as a viewfinder, aim at your subject, and press the joystick. The device saves the photo in the default folder,  
or in the folder you have defined.  
Tip: To zoom in or out before taking a picture, scroll up or down.  
3. If you do not want to keep the saved photo, select Options > Delete. Select Back to return to the viewfinder to take another  
picture. Select Options > Go to Gallery to view the photo in Gallery.  
If the light is dim, select Options > Night mode after you have opened Camera but before taking a picture.  
To adjust the image, select Options > Adjust > White balance or Colour tone.  
To take pictures in a sequence, select Options > Sequence mode. The camera takes six pictures in a row.  
To take timed pictures, select Options > Self-timer, select the desired timeout, and press Activate. The camera takes a picture  
after the timeout has passed.  
Tip: You can view and modify photos in Menu > Media > Gallery > Images.  
Record a video clip  
1. Select Camera, and scroll right to activate the video recorder.  
2. To start recording a video clip, press the joystick.  
3. The remaining recording time is shown on the top of the display. To pause the recording, select Pause; to resume the  
recording, select Continue.  
4. To stop the recording, select Stop. The device saves the clip in the default folder, or in the folder you have defined.  
5. If you do not want to keep the saved video clip, select Options > Delete. Select Back to return to the viewfinder to record  
another video clip. Select Options > Play to view the video clip in the RealPlayer application.  
Insert pictures into messages  
When you are creating a new multimedia message, you can open the camera to insert a new picture into the message.  
To insert a picture into a multimedia message, select Options > Insert new > Image. The viewfinder shows you the image to be  
captured. To take a picture, press the joystick. To insert the picture in the message, press the joystick.  
Insert videos into messages  
When you are creating a new multimedia message, you can open the camera to insert a new video into the message.  
To insert a video into a multimedia message, select Options > Insert new > Video clip. Press the joystick to start recording. To  
insert the video in the message, select Options > Select.  
Settings  
To edit the image settings, select Options > Settings > Image, and define the following:  
Image quality Define how much the picture is compressed when being saved. High provides the best image quality, but  
takes more memory. Normal is the default quality setting. Basic takes the least amount of memory.  
Show captured img. — Select whether you want the captured image to be displayed after the capture.  
Image resolution — Select the resolution of the images you capture.  
Default image name — Select Date or Text for the default title assigned to a picture. Date assigns the date of the capture as  
the title. Text assigns the term you define and a number to the picture.  
Memory in use — Select the memory to use for storing images: Phone memory or Memory card.  
Copyright © 2006 Nokia. All Rights Reserved.  
61  
                 
C a m e r a  
To edit the video settings, select Options > Settings > Video, and define the following:  
Length — Select the length of the video clips that you record. The maximum length of a video clip depends on the available  
memory.  
Video resolution — Select the resolution to use during video recording. The default setting for the resolution is always the  
lowest setting.  
Default video name — Select Date or Text for the default title assigned to a recorded video. Date assigns the date of the  
recording as the title. Text assigns the term you define and a number to the recorded video.  
Memory in use — Select the memory to use for storing recorded videos: Phone memory or Memory card.  
Copyright © 2006 Nokia. All Rights Reserved.  
62  
10.  
Office applications  
Select Menu > Office.  
Some office applications are not available in all languages.  
Opening a large file may not be possible or it may take a while.  
File manager  
With File mgr., you can manage the contents and properties of files and folders. You can open, create, move, copy, rename, and  
search for files and folders. Copyright protection may prevent sending some files.  
Manage files  
To manage files, scroll to a folder or file, and select Options.  
Select the following:  
Open Open a file. Scroll to the desired file, and select OK.  
Send — Send selected files. Scroll to the desired files, and select OK.  
Delete Delete selected files. Scroll to the desired files, and select Clear.  
Move to folder To move the folder or file to another folder, scroll to the desired file or folder, and select OK. Default folders  
such as sound clips in gallery cannot be moved or deleted.  
Copy to folder — Save a copy of the folder or file in another folder. Scroll to the desired file or folder, and select OK.  
New folder Create a folder.  
Mark/Unmark Open a submenu.  
Rename Rename a file or folder. Scroll to the desired file or folder, enter the new name, and select OK.  
Find — Search for specific folders or files. Select the type of memory to search, and enter the text that you wish to find.  
Receive via infrared Receive a file using an infrared connection.  
View details View information about files.  
Memory details Check the memory consumption in device memory or a memory card.  
Search for files  
1. To search for files, select Options > Find.  
2. Select the memory you want to search.  
3. Enter the search text, and press the joystick. The folders and files whose names contain the search text are displayed.  
4. Select Find to conduct another search.  
Documents  
You can open, edit, and save documents created with Microsoft Word for Windows versions 97 or later. Note that not all features  
and formatting of the original files are supported.  
Select Menu > Office > Docum..  
To open an existing document, browse for the folder and document, and press the joystick. To read the document, select the  
middle view.  
Tip: To open a recently used document, select Options > Most recent files, select the document, and press the joystick.  
To create a new document, select Options > New file. Select Blank to create a new document without using a template or Use  
template to create a document based on an existing template.  
To read a document, select the middle view and Options. You can browse for different types of objects in the document, zoom  
in or out, switch between full and normal screen views, or view objects, such as images. You can also search for text and edit  
application settings such as zooming, scrolling, and handling of invisible characters.  
Tip: If you are reading a large document and want to continue to read it later, select Back to close the document. Do  
not change to the editing mode.  
Tip: To switch between full and normal screen views in an open document, press *. To zoom in, press 5, and to zoom  
out, press 0.  
View objects in a document  
To view all objects, such as tables, comments, workbooks, and video clips in their place in the document, select the middle view  
and Options > Browse > Pages and objects.  
Copyright © 2006 Nokia. All Rights Reserved.  
63  
               
O f f i c e a p p l i c a t i o n s  
To open a table or comment, scroll to the object or its icon, and press the joystick twice.  
To open an image or go to a hyperlink or reference, scroll to the object, and press the joystick three times.  
Tip: Select Options > Back to reference to return to the link of the referenced item.  
Format documents  
To be able to edit a document, you must activate the edit mode: select the middle view and Options > Edit document.  
To edit the font, select the text and Options > Format > Font. You can change the font type, size, color, and background. Select  
Options > Preview to view the current formatting.  
To format the font style, select the text and Options > Format > Font formatting. Select the appropriate formatting option. You  
can add bold, italic, underline, and strikethrough formatting, or position the text in superscript or subscript format.  
To format a paragraph, select the paragraph and Options > Format > Paragraph. You can modify the text alignment, line spacing,  
and left and right margins.  
To insert bullets, insert the cursor in the text or paragraph, and select Options > Format > Bullets. In the bullet page of the  
formatting settings, you can set the bullets to be visible.  
To format the border settings, select Options > Format > Borders. The current border is displayed. Select the border you want  
to modify, and press the joystick. Select the border style and color you want. Select Back > Options > Apply to, and the location.  
For example, if you select Top, the border settings are assigned to the top border.  
To insert an object into a document, select Options > Insert object. Scroll to the type of object you want to insert, and select  
Options > Insert new to open the corresponding editor and create a new file, or Insert existing to open a list of existing files.  
To format the style settings of a paragraph, select Options > Format > Style. Select the style you want to format and Options >  
Edit. Select New style to add a new style. In the style editing view, select Options > Format, and the style you want. You can  
modify the font, formatting, paragraph, bullet, and border styles.  
To save a document, select Options > Saving options > Save as. Specify the file name and location where the file is saved. You  
can also specify the file type.  
View document structure  
To view the document outline, select the left view. Select Options > Expand or Collapse to show only main chapters or all  
subchapters. If there are objects in the document, select Options > Display objects or Display headings to switch between object  
list and chapter heading views.  
Tip: To open a selected chapter in the normal view, scroll to the chapter, and press the joystick.  
Preview the page layout  
To preview the page layout, select the view on the right and Options.  
Define the following options:  
Normal view — Show the current open page in normal view.  
Pan and zoom Zoom the page layout view.  
View — Select Full screen or Normal screen to switch between full screen and normal views.  
To zoom the page layout, select the view on the right, scroll to the desired page, and select Options > Pan and zoom. A black  
selection frame appears above the page layout, showing the area to zoom. Select the area and Options > Zoom.  
Select from the following options:  
In or Out — Select In to zoom in one step in the selected area, or Out to zoom out one step in the selected area.  
Fit to screen Adjust the zoom level to fit the page to the screen width.  
Ratio Edit the zoom level, enter the zoom ratio between 10 and 999, and select OK.  
Tip: While the selection frame is displayed, scroll left, right, up, or down with the joystick to move around the page.  
Press 5 to reduce and 0 to enlarge the selection frame. Press the joystick to zoom the selected area.  
Find text  
To find a piece of text from the document, select Options > Find, enter the text in the Find: field, and press the joystick.  
To change search options such as case sensitivity and search direction, select Options > Search options.  
To find and replace a piece of text in the document, in the editing mode, select Options > Find and replace. Enter the text in the  
Find: field, and enter a replacement text in the Replace with: field. Select Options > Replace. When the text is found, select  
Copyright © 2006 Nokia. All Rights Reserved.  
64  
         
O f f i c e a p p l i c a t i o n s  
Replace to replace the text and move to the next match, or select Ignore to skip the current match and Next to move to the next  
match.  
Tip: To skip the current match and move to the previous and next ones, scroll up and down with the joystick.  
Table editor  
You can view tables created in applications, like documents and MS Word.  
To view a table in a file, scroll to the file so that a dotted line appears around it, and press the joystick.  
To change the selected cell, scroll up, down, left or right. If the selected cell does not fit into visible area, pressing the joystick  
pans the whole content first before the cell changes.  
To edit the text in a cell, select the cell, and press the joystick. To end editing, press the joystick again.  
Select Options and from the following options:  
Zoom Zoom the table view in, out and to edit a zoom ratio.  
Format Modify the font style and formatting, paragraphs, bullets, and borders.  
Cell size Change the size of the cells, rows and columns.  
Cells — Select option to insert, delete, merge or separate cells.  
Copy table Copy the text of the whole table to the clipboard.  
Sheet  
Select Menu > Office > Sheet.  
You can store data in a file that is called a workbook. Each workbook contains at least one worksheet. A workbook can also  
contain charts, which are based on data from a worksheet.  
To open an existing workbook, browse for the folder where the file is saved, and press the joystick.  
To create a new workbook, select Options > New file. Select Blank to create a new file without using any template or Use  
template to create a file based on an existing template. Select the worksheet in the outline view, and press the joystick to open  
the file.  
Tip: To open a recently used workbook, select Options > Most recent files.  
Outline view  
Outline view enables you to open and navigate worksheets, charts, and named cells.  
In outline view, each worksheet has its own main level icon. Under the main level there are sub-items for charts and named  
cells.  
To open the outline view, scroll to the folder and file, and press the joystick. The outline view opens. Recently used worksheet  
opens the latest view and settings.  
To show and hide charts and cells, scroll to the worksheet, press the joystick, and select Options > Collapse or Expand.  
To delete or rename worksheets, charts, or named cells, scroll to the item, and select Options > Worksheet, Chart, or Named  
cell, and the appropriate option.  
To create a new worksheet, chart, or named cell, scroll to the position you want to add the new item, and select Options >  
Insert > Worksheet, Chart, or Named cell.  
Work with worksheets  
To insert data into cells, open the worksheet view. Use the joystick to move to the cell, and select Options > Show cell field >  
Edit cell field. An upper part editing field opens. Enter the data, and select Done to finish editing.  
To select a range of cells, press and hold the edit key while you scroll right.  
To select rows, move the cursor to the first cell on a row, and press and hold the edit key while you scroll left. To select columns,  
move the cursor to the first cell on a column, and press and hold the edit key while you scroll up.  
To select the entire worksheet, move the cursor to cell A1, and press and hold the edit key while you scroll up and left.  
To modify the worksheet view, select Options > View.  
Select from the following options:  
Pan worksheet Define the size of the visible area of the whole worksheet.  
Full screen — Switch to the full screen view.  
Hide headers Hide header field and release more space for the worksheet grid.  
Hide gridlines Hide gridlines.  
Copyright © 2006 Nokia. All Rights Reserved.  
65  
           
O f f i c e a p p l i c a t i o n s  
Tip: To switch between the full and normal screen views, press *. To zoom in, press 5; to zoom out, press 0.  
To add a comment to the selected cell, select Options > Advanced options > Insert comment. Write a comment, and select OK.  
The cell is marked with a small triangle in the upper right corner of the cell.  
To keep rows visible when scrolling, select a cell below the area that you want to remain visible and Options > Advanced  
options > Freeze panes. To keep columns visible, select a cell to the right of the area that you want to remain visible and  
Options > Advanced options > Freeze panes.  
To change the size of rows and columns, select Options > Cell size > Row height or Column width.  
To sort rows from left to right, select the cells you want to sort and Options > Advanced options > Sort rows. You can select the  
number of the row to use as a primary sorting criteria. You can change the direction of the sorting order and ignore or match  
the case sensitivity.  
To sort columns from top to bottom, select the cells you want to sort and Options > Advanced options > Sort columns. You can  
select the column to use as a primary sorting criteria. You can change the direction of the sorting order and ignore or match  
the case sensitivity.  
To format a font style, select the cells whose font style you want to modify and Options > Format > Font. You can change the  
font type, size, text color, and background color of the cell.  
To change a font formatting, select the cells you want to format and Options > Format > Font formatting. You can bold, italicize,  
underline, strikethrough, or position the text in superscript or subscript format within a cell.  
To align cell contents, select the cells whose alignment you want to modify and Options > Format > Alignment. You can change  
both the horizontal and vertical alignment and wrap text to adjust the row height of the selected cells to display the entire  
content of a cell.  
To format cell borders, select the cells whose borders you want to modify and Options > Format > Borders. You can modify all  
or only vertical, horizontal, upper, lower, left or right borders. Select Options > Change to edit the style and color of the borders.  
To change the number format, select the cells whose number format you want to modify and Options > Format > Numbers.  
Select the number format from the list. If the format you select includes decimal values, enter a number from 0 to 12 to indicate  
the decimal place.  
Example: If you want to compare and calculate different loan rates, you can set the number format to Percentage.  
Work with cells  
To edit a cell, select a cell and Options > Show cell field > Edit cell field. An upper part editing field opens. Start entering the data,  
and select Done when you finish editing.  
To insert cells, select the area where you want to insert new cells and Options > Cells > Insert. You can insert cells above (Shift  
cells down) or to the left (Shift cells right) of the selected range. If you select only one cell, only one new cell is inserted. If you  
select a range of cells, a corresponding range of blank cells is inserted. You can also insert a new row or column.  
To clear contents or format from cells, select the cells and Options > Cells > Clear. If you select Formats, the formatting of the  
selected cells is removed, but the content remains. The default style is used. If you select Content, the content of the selected  
cells is deleted, but the formatting stays the same. You can also remove both formatting and contents of the selected cells.  
To delete cells, rows, or columns, select the items you want to delete and Options > Cells > Delete. You can delete an entire row  
or column. If you select Shift cells left, the selected cells are deleted, and the cells right of the selected cells are shifted left. If  
you select Shift cells up, the cells below the deleted cells are shifted up.  
Tip: When you delete information on which a chart is based, the information is also removed from the chart.  
Insert functions  
Functions are used for automating calculations.  
To insert a function into a cell, select a cell. Select Options > Insert > Function and a function from the list. For example, #MIN  
finds the lowest value in the numeric contents of a selected range of cells, #AVERAGE calculates the average of the values, and  
#SUM adds the values together. Once you have selected a function, press the joystick. The function is inserted into the selected  
cell. On the worksheet, enter the cells you want to include in the function inside the brackets, and press the joystick.  
Tip: Before inserting a function, verify that Options > Show cell field > Edit grid is active and that the selected cell is  
empty or starts with =.  
Example: You want to add up the numbers in cells C2 to C6 and have the results appear in cell C7. Select cell C7 and  
Options > Insert > Function. Select #SUM, and press the joystick. Enter C2:C6 inside the brackets, and press the joystick.  
The sum appears in cell C7.  
Copyright © 2006 Nokia. All Rights Reserved.  
66  
     
O f f i c e a p p l i c a t i o n s  
To get more information on a function, select a cell and Options > Insert > Function. Select a function from the list and  
Options > Description.  
Web links  
To open a Web link, select the cell with the Web link. Select Options > Link > Go to.  
To edit a Web link, select the cell with the Web link. Select Options > Link > Edit. You can edit the Wed address and the name of  
the link.  
Create and modify charts  
When you change the information on a worksheet, the chart is updated simultaneously.  
To open a chart, open the outline view, select the worksheet and chart, and press the joystick. If charts are not visible, select  
Options > Expand.  
To create a new chart, select the worksheet cells that contain the information you want to include in the chart and Options >  
Insert > Chart. To change the general appearance of an existing chart, open a chart view. Select Options > View > Chart. You can  
change the name of the chart and define the cell area. You can change the type of the chart, and make the chart two or three-  
dimensional or change the color of the background and axis. Scroll right to add a title to the chart and axis.  
To format a chart in more detail, open a chart view. Select Options > View and the object you want to edit. You can change the  
series, X-axis, and Y-axis settings (such as the tick marks of either axis).  
Find text  
To find text, open the worksheet view, and select Options > Find. Enter the text in the Find: field, and press the joystick. When  
the cell is found, press the joystick again to find the next match.  
To change the search content and direction, select Options > Search options.  
To find and replace a cell that includes text, open the worksheet view, and select Options > Find. Enter the text to be replaced  
in the Find: field, enter the new text in the Replace with: field, and press the joystick. When the cell is found, select Replace to  
replace the text and move to the next match. Select Ignore to skip the current match and Next to move to the next match.  
Tip: To skip the current match and to move to the previous and next match, scroll up and down.  
Presentation  
You can open, view, edit, and save presentations created with Microsoft PowerPoint 97 or later. You can also create new  
presentations. Note that not all features and formatting of the original files are supported.  
Select Menu > Office > Presentat..  
To open an existing presentation, browse for the folder and file, and press the joystick.  
Tip: To open a recently viewed presentation, select Options > Most recent files.  
To create a new presentation, select Options > New file. Select Blank to create a new presentation without using a template or  
Use template to create a presentation based on an existing template.  
To use an existing template, scroll to the template folder and file, and press the joystick. Select Open template to modify the  
template or Use template to create a new document based on the current template.  
View slide shows  
To start a slide show, select Options > Presentation.  
Select from the following options:  
Manual Move from one slide to another manually.  
Slide show Move from one slide to another manually, or use the automatic slide switching. You must specify the duration  
for a slide.  
Manual looped The slide show continues from the beginning when the last slide of a presentation has been shown.  
Looped slide show The slide show continues automatically from the beginning when the last slide of a presentation has  
been shown.  
To move between slides in a slide show, scroll up to display a previous slide and down to display the next slide.  
To end the slide show, press the right selection key.  
Show slide shows with a data projector  
You can show slide shows with a compatible data projector, or other compatible projection system.  
Copyright © 2006 Nokia. All Rights Reserved.  
67  
                 
O f f i c e a p p l i c a t i o n s  
To be able to show slide shows with a compatible data projector, you must install the drivers of the data projector. If the drivers  
are not installed and the devices are not connected, the menu options are not visible. For more information, check with the  
data projector manufacturer or its representative.  
To show slide shows with a data projector, select the presentation and Options > View > Data projector. From the list of devices,  
select the device you want to use. Select Options > Enable to show screen content. To start the slide show, select Options >  
Presentation > Slide show.  
To stop showing a slide show with a data projector, select Options > View > Disable data projector.  
Work with different views  
The presentation application consists of different views that help you when reading and creating presentations.  
To switch between the different views, scroll right and left with the joystick.  
Layout view  
To open the layout view, select the view in the middle. To enable or disable the visibility of charts, comments, tables, images,  
and shapes, select Options > Settings, scroll to the settings item, and press the joystick.  
To work in the layout view, select Options. You can edit and insert new slides, switch between different screen views, delete or  
hide certain slides, undo or redo latest modifications, and see a slide show. You can also save the presentation, and send it to  
another device. The available options may vary.  
Outline view  
The outline view is used to navigate through long presentation documents. The view enables fast vertical scrolling, rearranging  
of slides, and editing of objects.  
To open the outline view, scroll to the view on the left. In the outline view, each slide has its own main level entry. Under the  
main level there is a sublevel for each text field and object.  
To view the slide content, select Options > Expand. To hide the content, select Options > Collapse. To collapse or expand all  
entries, select Options > View > Collapse all or Expand all.  
To change the order of slides, scroll to the slide you want to move, and select Options > Slide > Move. Scroll up and down to  
select a new location, and select OK.  
To insert new slides into a presentation, select Options > Insert new slide. Select a template for the new slide. The new slide is  
inserted after the currently selected slide.  
To copy, paste, or remove slides, select a slide and Options > Slide > Copy, Paste, or Delete.  
To show or hide slides in the outline view, select a slide and Options > Slide > Show or Hide.  
Notes view  
In the notes view, you can read notes that are attached to slides in the presentation. You can also add your own notes.  
To open the notes view, scroll to the view on the right. Each slide has its own main level entry. Under the main level there is a  
sublevel for notes. If notes are not visible, select Options > View > Expand all. To edit a note, scroll to the note, and press the  
joystick.  
To add a note, scroll to a slide without notes, and select Options > Create note.  
To delete a note, select the note and Options > Delete note.  
Master slide view  
The master slide view lets you view layout details. If you edit the master slide, the changes are updated to all slides in a  
presentation.  
To open the master slide view, open the layout view, and select Options > View > Master slide. To edit the master slide, press  
the joystick.  
Edit presentations  
To edit a presentation, open the layout view, and select Options > Edit slide. Scroll right or down with the joystick to move  
forward and left or up to move backward. Select Options.  
Define the following options:  
Add title, Add subtitle, Add text, Insert table, Insert image Add a new text or object inside the selected area.  
Edit text, Edit table, Edit document, Edit workbook Edit the selected object.  
Edit object — Select Move to move the object, scroll to the item, and press the joystick. Select Resize to change the size of the  
object. Scroll right and left to change the horizontal size of the object and up and down to change the vertical size. To accept  
Copyright © 2006 Nokia. All Rights Reserved.  
68  
           
O f f i c e a p p l i c a t i o n s  
the changes, press the joystick. Select Rotate to rotate the object. Scroll right to rotate the object clockwise and left to rotate  
counterclockwise. To accept the changes, press the joystick. Select Properties to edit text, line, border, or background  
properties of the object.  
Object Delete, copy, paste, or add a link to the selected object.  
Object position Change the layered position of the selected object in the presentation: up, down, front, or back.  
Insert Add a new text box, image, shape, table, or comment to the presentation.  
Undo, Redo — Withdraw the latest modifications.  
To move one or several objects inside a slide, scroll to the objects, and press the joystick in each object you want to edit. Select  
Options > Marked objects > Move. To move the position of the marked objects, scroll right, left, up, and down. To accept the  
changes, press the joystick. You can also delete or align the marked objects, and create a group of the marked objects. The group  
forms a new modifiable object. To unmark previously marked objects, select Options > Unmark all.  
To define font settings, open the layout view, and select Options > Edit slide. Scroll to the text field, and select Options > Edit  
text > Options > Format > Font. You can change the font type, size, and color.  
To format the font style, open the layout view, and select Options > Edit slide. Scroll to the text field, and select Options > Edit  
text > Options > Format > Font formatting. Select the appropriate formatting option. You can add bold, italic, underline, and  
strikethrough formatting, or position the text in superscript or subscript format.  
To format a paragraph, open the layout view, and select Options > Edit slide. Scroll to the text field, and select Options > Edit  
text > Options > Format > Paragraph. You can change the text alignment, line spacing, and width of the left margin.  
To change the bullet style, open the layout view, and select Options > Edit slide. Scroll to the text field, and select Options > Edit  
text > Options > Format > Bullets. You can set the bullets to be visible, change the type of the bullet, and define the size and  
color.  
To edit the text box settings, select the layout view and Options > Edit slide. Scroll to the text box, and select Options > Edit  
object > Properties. You can change the position of the text inside the text box, and turn text wrapping on or off.  
To modify borders, select the layout view and Options > Edit slide. Scroll to the object that has borders, and select Options >  
Edit object > Properties. You can modify all or only vertical, horizontal, upper, lower, left, or right borders.  
To format line settings, select the layout view and Options > Edit slide. Scroll to the object that has lines, and select Options >  
Edit object > Properties. You can change the line color and style of elements such as dots, dashes, or thick lines.  
To format background settings, select the layout view and Options > Edit slide. Scroll to an object, and select Options > Edit  
object > Properties. You can change the color of the background, and enable or disable the visibility of a styled background.  
Edit tables  
To edit a table, select the layout view and Options > Edit slide. Scroll to the table, and select Options > Edit table. A highlight  
indicates the active cell. To change the selected cell, scroll up, down, left, and right. Select Options.  
Select from the following options:  
Edit text Modify the text of the current cell.  
Insert Add rows or columns to the table. A new column is inserted to the left of the selected cell, and a new row is inserted  
above the selected cell.  
Delete Remove full rows or columns from the table.  
View Zoom in or out in the table, adjust the zoom level to fit the page to the screen width, or change the zoom level.  
Undo and Redo — Withdraw the latest modifications.  
Find text in a presentation  
To find a piece of text from in the presentation, select any of the views. Select Options > Find, enter the text in the Find: field,  
and press the joystick.  
To change the search option for case and whole words, select Options > Search options.  
To find and replace a piece of text in the presentation, select any of the views. Select Options > Find. Enter the text to be replaced  
in the Find: field, enter the new text in the Replace field, and press the joystick. When the text is found, select Replace to replace  
the text and move to the next match, or select Ignore to skip the current match and Next to move to the next match.  
Tip: To skip the current match and move to the previous and next ones, scroll up and down.  
Screen export  
You can show the screen of the device to an audience with a compatible data projector, or other compatible projection system.  
The screen content is transferred to the data projector using, for example, a Bluetooth connection.  
Select Menu > Office > Screen export.  
Copyright © 2006 Nokia. All Rights Reserved.  
69  
       
O f f i c e a p p l i c a t i o n s  
To be able to show screen content with a compatible data projector, you must install the drivers of the data projector. For more  
information, check with the data projector manufacturer or its representative.  
Not all applications support this feature. You can start the external viewer in two ways: from the Office folder or inside an  
application that supports it.  
Show screen content  
To show screen content with a data projector, open the screen export application, and select Options > Select device. In the list  
of available devices, scroll to the device you want to use, and select OK. Select Options > Enable to show screen content.  
To hide the screen content, select Options > Hide. The screen exporter application is moved to the background.  
To stop showing screen content, select Options > Disable.  
Print  
Print a message or file from the device. Preview a print job, define page layout options, select a printer, or print to a file.  
Before you print, make sure that your device is properly connected to the printer.  
To print a message or file, open the message or file, and select Options > Printing options.  
Define the following options:  
Printer — Select an available printer from the list.  
Print — Select All pages, Even pages, or Odd pages as the print range.  
Print range — Select All pages in range, Current page, or Defined pages as the page range.  
Number of copies — Select the number of copies to print.  
Print to file — Select to print to a file and determine the location for the file.  
You may not be able to print all messages, such as multimedia messages or other special message types.  
To preview a file or message before you print, select Options > Printing options > Preview.  
Change the page layout before printing  
To change the page layout before printing, select Options > Printing options > Page setup and from the following tabs:  
Paper size Change the paper size or orientation and customize the height and width.  
Margins Change the size of the left, right, top, or bottom margins.  
Header The maximum length of the header is 128 characters. You can set the distance from the header to the text and  
choose to include the header on the first page of the document.  
Footer The maximum length of the footer is 128 characters. You can set the distance from the footer to the text.  
To add or delete a printer, select Menu > Office > Printers > Options > Add or Delete.  
Copyright © 2006 Nokia. All Rights Reserved.  
70  
     
11.  
Settings  
Select Menu > Tools > Settings.  
You can define and modify various settings of your device. Modifying these settings affects the operation of your device across  
several applications.  
Some settings may be preset for the device or sent to you in a configuration message by your network operator or service  
provider. You may not be able to change such settings.  
Scroll to the setting that you want to edit, and press the joystick to do the following:  
Switch between two values, such as on or off.  
Select a value from a list.  
Open a text editor to enter a value.  
Open a slider to decrease or increase the value by scrolling left or right.  
Phone settings  
Select Phone to change the language settings, standby mode settings, and display settings of your device.  
General settings  
Select General and from the following:  
Phone language — Select a language from the list. Changing the device language affects every application in your device.  
When you change the language, the device restarts.  
Writing language — Select a language from the list. Changing the writing language also affects the characters that are  
available when writing text and the predictive text dictionary that is used.  
Predictive text — Select On to use predictive text input. The predictive text dictionary is not available for all languages.  
Welcome note / logo — Select Default to use the default image, Text to enter a welcome note of your own, or Image to select  
an image from the Gallery. The welcome note or image is displayed briefly each time you switch on the device.  
Orig. phone settings Restore the original device settings. To do this, you need your device lock code. After resetting, the  
device may take a longer time to power on. Documents, contact information, calendar entries, and files are unaffected.  
Standby mode settings  
Select Standby mode and from the following:  
Active standby — Select On to have shortcuts to different applications available in the active standby mode.  
Left selection key, Right selection key Change the shortcuts that open from the left and right selection keys in the standby  
screen.  
Navigation key right, Navigation key left, Navigat. key down, Navigation key up, Selection key Change the shortcuts that  
open when you scroll to different directions. These settings are not available if you select Active standby > On.  
Standby apps — Select the applications that you want to access from the active standby.  
Active standby mailbox — Select the inbox or the mailbox that is shown in the active standby.  
Active standby plug-ins — Select the plug-ins that are shown in the active standby. You can, for example, see how many voice  
mails you have. Even if you switch off the active standby notifications for missed calls and messages, the default notification  
will still show them. The available plug-ins may vary.  
Display settings  
Select Display and from the following:  
Light sensor Adjust the amount of light required to illuminate the device display.  
Power saver time-out — Select the amount of time before the screen saver is activated. Activating the screen saver lengthens  
the device operating time.  
Light time-out — Set how quickly after last keypress the display dims.  
Call settings  
Select Call and from the following:  
Send my caller ID — Select Yes to display your phone number to the person you are calling or Set by network to let the network  
to determine whether your caller ID is sent.  
Send my net call ID — Set this feature on if you want to display your net caller ID to the person you are calling.  
Call waiting — Select Activate to be notified of a new incoming call while you have a call in progress or Check status to check  
if the function is active on the network.  
Internet call waiting Activate this feature to be notified of a new incoming call while you have a net call in progress.  
Copyright © 2006 Nokia. All Rights Reserved.  
71  
                     
S e t t i n g s  
Internet call alert — Set this on if you want the device to respond to the caller that it is busy. If you set this off, the device  
emits a busy tone to the caller and you receive a notification about the missed call.  
Default call type — Select Cellular to make normal calls to the phone number or Internet to use VoIP to call the number or  
address.  
Reject call with SMS — Select Yes to send a text message automatically to the person who is calling you informing why you  
cannot answer their incoming call.  
Message text Enter the text that is sent when you cannot answer an incoming call and want to automatically send a text  
message as a reply.  
Image in video call — Select Use selected to select a still image to be displayed instead of a video during a video call or  
None to not send any image during a video call.  
Automatic redial — Select On to redial a number if it was busy at the first call attempt. Your device makes a maximum of 10  
attempts to connect the call.  
Summary after call — Select On to briefly display the approximate duration of the last call.  
Speed dialling — Select On to activate speed dialing on your device. To dial a phone number assigned to the speed dialing  
keys (2-9), press and hold the key.  
Anykey answer — Select On to answer an incoming call by briefly pressing any key, except the end key.  
Line in use — Select Line 1 or Line 2 to change the phone line for outgoing calls and text messages (network service). This  
setting is displayed only if the SIM card supports the alternate line service and a subscription to two phone lines.  
Line change — Select Disable to prevent line selection (network service). To change this setting, you need the PIN2 code.  
Internet call alert — Select Off to notify incoming net calls that your device is busy or On to accept incoming net calls.  
Connection settings  
Select Menu > Tools > Settings > Connection and from the following:  
Access points — Set up new or edit existing access points. Some or all access points may be preset for your device by your  
service provider, and you may not be able to create, edit, or remove them.  
Access point groups — Set up new or edit existing access point groups that are used in automatic connection establishment  
and e-mail roaming.  
Packet data Determine when packet data connections are used, and enter the access point if you use your device as a  
modem for a computer.  
Internet tel. settings Define settings for net calls.  
SIP settings View or create session initiation protocol (SIP) profiles.  
Data call — Set the time-out period after which data call connections automatically end.  
VPN — Install and manage VPN policies, manage VPN policy servers, see the VPN log, and create and manage VPN access  
points.  
Wireless LAN Determine if the device displays an indicator when a wireless LAN is available, and how often the device  
searches for networks.  
Configurations View and delete trusted servers from which your device may receive configuration settings.  
To obtain information about wireless LAN or subscribing to a packet data service and the appropriate connection and  
configuration settings, contact your network operator or service provider.  
The settings available for editing may vary.  
Access points  
Select Menu > Tools > Settings > Connection > Access points.  
An access point is where your device connects to the network by way of a data connection. To use e-mail and multimedia services  
or to browse web pages, you must first define access points for these services.  
An access point group is used for grouping and prioritizing access points. An application can use a group as a connection method  
instead of a single access point. In that case, the best available access point inside a group is used for making the connection,  
and in case of e-mail, also for roaming.  
Some or all access points may be preset for your device by your service provider, and you may not be able to create, edit, or  
remove them.  
Access point groups  
Select Menu > Tools > Settings > Connection > Access point groups.  
An access point group is used for grouping and prioritizing access points. An application can use a group as a connection method  
instead of a single access point. In that case the best available access point inside a group is used for making connection and  
in case of e-mail, also for roaming. See "Access point groups," p. 51.  
Copyright © 2006 Nokia. All Rights Reserved.  
72  
       
S e t t i n g s  
Packet data  
Select Menu > Tools > Settings > Connection > Packet data.  
Your device supports packet data connections, such as GPRS in the GSM network. When you are using your device in GSM and  
UMTS networks, it is possible to have multiple data connections active at the same time; access points can share a data  
connection, and data connections remain active (for example, during voice calls). See "Connection manager," p. 49.  
Packet data settings  
The packet data settings affect all access points using a packet data connection.  
Select from the following:  
Packet data conn. — Select When available to register the device to the packet data network when you switch the device on  
in a supported network. Select When needed to establish a packet data connection onlywhen an application or action requires  
it.  
Access point Enter the access point name provided by your service provider to use the device as a packet data modem to  
your computer.  
These settings affect all access points for packet data connections.  
Net call settings  
Select Menu > Tools > Settings > Connection > Internet tel. settings. Select Options > New profile or Options > Edit.  
Scroll to Name, press the joystick, enter a name for the profile, and select OK.  
Scroll to SIP profiles, press the joystick, select a profile and OK. SIP protocols are used for creating, modifying, and terminating  
communications sessions such as net calls with one or more participants. SIP profiles include settings for these sessions.  
To save your settings, press Back.  
Session initiation protocol (SIP) settings  
Select Menu > Tools > Settings > Connection > SIP settings.  
Session initiation protocols (SIP) are used for creating, modifying, and terminating certain types of communication sessions  
with one or more participants (network service). SIP profiles include settings for these sessions. The SIP profile used by default  
for a communication session is underlined.  
To create a SIP profile, select Options > Add new > Use default profile or Use an existing profile.  
To edit a SIP profile, scroll to it, and press the joystick.  
To select the SIP profile you want to use by default for communication sessions, scroll to the profile, and select Options > Default  
profile.  
To delete a SIP profile, scroll to it, and press the clear key.  
Edit SIP profiles  
Select Menu > Tools > Settings > Connection > SIP settings > Options > Add new or Edit.  
Select from the following:  
Profile name Enter a name for the SIP profile.  
Service profile — Select IETF or Nokia 3GPP.  
Default access point — Select the access point to use for the Internet connection.  
Public user name Enter your user name received from your service provider.  
Use compression — Select if compression is used.  
Registration — Select the registration mode.  
Use security — Select if security negotiation is used.  
Proxy server Enter the proxy server settings for this SIP profile.  
Registrar server Enter the registration server settings for this SIP profile.  
The settings available for editing may vary.  
Edit SIP proxy servers  
Select Menu > Tools > Settings > Connection > SIP settings > Options > Add new or Edit > Proxy server.  
Proxy servers are intermediate servers between a browsing service and its users used by some service providers. These servers  
may provide additional security and speed up access to the service.  
Select from the following:  
Proxy server address Enter the host name or IP address of the proxy server in use.  
Realm Enter the proxy server realm.  
User name and Password Enter your user name and password for the proxy server.  
Allow loose routing — Select if loose routing is allowed.  
Copyright © 2006 Nokia. All Rights Reserved.  
73  
             
S e t t i n g s  
Transport type — Select UDP or TCP.  
Port Enter the port number of the proxy server.  
Edit registration servers  
Select Menu > Tools > Settings > Connection > SIP settings > Options > Add new or Edit > Registrar server.  
Select from the following:  
Registrar serv. addr. Enter the host name or IP address of the registrar server in use.  
Realm Enter the registrar server realm.  
User name and Password Enter your user name and password for the registrar server.  
Transport type — Select UDP or TCP.  
Port Enter the port number of the registrar server.  
Data call settings  
Select Menu > Tools > Settings > Connection > Data call.  
To set the time-out period after which data calls automatically end if no data has been transferred, select Online time, and press  
the joystick. Select User defined to enter the time yourself or Unlimited to keep the connection active until you select Options >  
Disconnect.  
VPN  
VPN access points  
To manage VPN access points, select VPN > VPN access points > Options, and from the following:  
Edit Edit the selected access point. If the access point is in use or its settings are protected, you cannot edit it.  
New access point Create a new VPN access point.  
Delete Delete the selected access point.  
VPN access point settings  
Contact your service provider for the correct access point settings.  
To edit VPN access point settings, select the access point and Options.  
Select from the following:  
Connection name Enter a name for the VPN connection. The maximum length of the name is 30 characters.  
VPN policy — Select a VPN policy to be used with this access point.  
Internet access pt. — Select the Internet access point to be used with this VPN access point.  
Proxy serv. address Enter the proxy server address of this VPN access point.  
Proxy port number Enter the number of the proxy port.  
Wireless LAN  
Select Menu > Tools > Settings > Connection > Wireless LAN.  
To have an indicator displayed when there is a wireless LAN available in your current location, select Show availability > Yes.  
To select the time interval for your device to scan for available wireless LANs and update the indicator, select Scan for  
networks.  
Advanced WLAN settings  
Select Menu > Tools > Settings > Connection > Wireless LAN > Options > Advanced settings. The wireless LAN advanced settings  
are normally defined automatically, and changing them is not recommended.  
To edit the settings manually, select Automatic config. > Disabled, and define the following:  
Long retry limit Enter the maximum number of transmission attempts if the device does not receive a receiving  
acknowledgement signal from the network.  
Short retry limit Enter the maximum number of transmission attempts if the device does not receive a clear-to-send signal  
from the network.  
RTS threshold — Select the data packet size at which the wireless LAN access point device issues a request to send before  
sending the packet.  
TX power level — Select the power level of your device when sending data.  
Radio measurements Enable or disable the radio measurements.  
Power saving — Select whether to save the power in the device battery.  
To restore all settings to their original values, select Options > Restore defaults.  
Copyright © 2006 Nokia. All Rights Reserved.  
74  
               
S e t t i n g s  
Security settings for wireless LAN access points  
WEP security settings  
Select Menu > Tools > Settings > Connection > Access points. Select Options > New access point, or select an access point and  
Options > Edit.  
In the access point settings, select WLAN security mode > WEP.  
Wired equivalent privacy (WEP) encryption method encrypts data before it is transmitted. Access to the network is denied to  
users who do not have the required WEP keys. When WEP security mode is in use, if your device receives a data packet not  
encrypted with the WEP keys, the data is discarded.  
In an Ad-hoc network, all devices must use the same WEP key.  
Select from the following:  
WEP key in use — Select the desired WEP key.  
Authentication type — Select Open or Shared.  
WEP key settings Edit the settings for the WEP key.  
WEP key settings  
Select Menu > Tools > Settings > Connection > Access points. Select Options > New access point, or select an access point and  
Options > Edit.  
In the access point settings, select WLAN security mode > WEP.  
In an Ad-hoc network, all devices must use the same WEP key.  
Select WLAN security sett. > WEP key settings and from the following:  
WEP encryption — Select the desired WEP encryption key length.  
WEP key format — Select whether you want to enter the WEP key data in ASCII or Hexadecimal format.  
WEP key Enter the WEP key data.  
802.1x security settings  
Select Menu > Tools > Settings > Connection > Access points. Select Options > New access point, or select an access point and  
Options > Edit.  
In the access point settings, select WLAN security mode > 802.1x.  
802.1x authenticates and authorizes devices to access a wireless network, and prevents access if the authorization process fails.  
Select WLAN security sett.. and from the following:  
WPA mode — Select EAP (Extensible Authentication Protocol) or Pre-shared key (a secret key used for device identification).  
EAP plug-in settings — If you selected WPA mode > EAP, select which EAP plug-ins defined in your device to use with the  
access point.  
Pre-shared key — If you selected WPA mode > Pre-shared key, enter the shared private key that identifies your device to the  
wireless LAN to which you connect.  
The settings available for editing may vary.  
WPA security settings  
Select Menu > Tools > Settings > Connection > Access points. Select Options > New access point, or select an access point and  
Options > Edit.  
In the access point settings, select WLAN security mode > WPA/WPA2.  
Select WLAN security sett.. and from the following:  
WPA mode — Select EAP (Extensible Authentication Protocol) or Pre-shared key (a secret key used for device identification).  
EAP plug-in settings — If you select WPA mode > EAP, select which EAP plug-ins defined in your device to use with the access  
point.  
Pre-shared key — If you select WPA mode > Pre-shared key, enter the shared private key that identifies your device to the  
wireless LAN to which you connect.  
The settings available for editing may vary.  
EAP  
To view the EAP (extensible authentication protocol) plug-ins currently installed in your device (network service), select Menu >  
Tools > Settings > Connection > Access points. Select Options > New access point and define an access point that uses wireless  
LAN as a data bearer and 802.1x or WPA/WPA2 as their security mode. Select WLAN security sett. > WPA mode > EAP, scroll to  
EAP plug-in settings, and press the joystick.  
EAP settings  
Select Menu > Tools > Settings > Connection > Access points. Select Options > New access point, or select an access point and  
Options > Edit.  
Select WLAN security mode > 802.1x or WPA/WPA2.  
Select WLAN security sett. > WPA mode > EAP, scroll to EAP plug-in settings, and press the joystick.  
Copyright © 2006 Nokia. All Rights Reserved.  
75  
   
S e t t i n g s  
The extensible authentication protocol (EAP) plug-ins are used in wireless networks to authenticate wireless devices and  
authentication servers, and the different EAP plug-ins make possible the use of various EAP methods (network service).  
To use an EAP plug-in when you connect to a WLAN using the access point, select the desired plug-in and Options > Enable. The  
EAP plug-ins enabled for use with this access point have a check mark next to them. To not use a plug-in, select Options >  
Disable.  
To edit the EAP plug-in settings, select Options > Configure.  
To change the priority of the EAP plug-in settings, select Options > Raise priority to attempt to use the plug-in before other plug-  
ins when connecting to the network with the access point, or Options > Lower priority to use this plug-in for network  
authentication after attempting to use other plug-ins.  
The available options may vary.  
Configurations  
To view and delete configurations for trusted servers, select Menu > Tools > Settings > Connection > Configurations.  
You can receive messages from your network operator, service provider, or company information management that contain  
configuration settings for trusted servers. These settings are automatically saved in Configurations. You may receive  
configuration settings for access points, multimedia or e-mail services, and IM or synchronization settings from trusted servers.  
To delete configurations for a trusted server, scroll to the server, and press the clear key. The configuration settings for other  
applications provided by this server are also deleted.  
Date and time settings  
Security settings  
Network settings  
Select Menu > Tools > Settings > Network.  
Define the following:  
Network mode — Select the network type. You can select GSM or UMTS to use the respective network or Dual mode to have  
your device automatically switch between the two. This setting may be preset for your device and not available for editing.  
If you set the device to use only the GSM network or only the UMTS network, you will not be able to make any calls, including  
emergency calls, or use other features requiring a network connection, if the selected network is unavailable.  
Operator selection — Select Manual to choose from available networks, or Automatic to have the device select the network  
automatically.  
Cell info display — Select On to set the device to indicate when it is used in Micro Cellular Network (MCN).  
Enhancement settings  
Select Menu > Tools > Settings > Enhancement.  
Warning: When you use the headset, your ability to hear outside sounds may be affected. Do not use the headset  
where it can endanger your safety.  
With most enhancements, you can select from the following settings:  
Default profile — Select the profile that is activated when you attach an enhancement to your device.  
Automatic answer Let the device answer phone calls automatically when an enhancement is attached. Select On to have  
the device answer an incoming call automatically after 5 seconds. If the ringing type is set to Beep once or Silent in the Profiles  
menu, automatic answer is disabled.  
Lights — Select On to illuminate the device while it is attached to an enhancement.  
Text phone settings  
If you use a text phone (TTY), you must connect it to your device before you can change the settings and use the text phone.  
Select from the following settings:  
Default profile — Select the profile that is activated when you attach a text phone (TTY, teletypewriter) to your device.  
Use text phone — Select Yes if you want to start using the text phone.  
Copyright © 2006 Nokia. All Rights Reserved.  
76  
                 
12.  
Organiser  
Select Menu > Organiser.  
Organiser includes tools that help you organize and manage the details of different events in your personal and business life.  
Calendar  
Select Menu > Organiser > Calendar.  
In Calendar, you can create and view scheduled events and appointments. You can also set alarms for calendar entries.  
You can synchronize your calendar data with a compatible computer using Nokia PC Suite. For information on synchronization,  
see the PC Suite guide.  
Create calendar entries  
You can create four types of calendar entries:  
Meeting entries have a specific date and time.  
Memo entries are related to the whole day but not to a specific time of the day. Memo entries do not appear in the weekly  
time schedule view.  
Anniversary entries remind you of birthdays and special dates. They refer to a certain day but not a specific time of the day.  
Anniversary entries are repeated every year.  
To-do note entries remind you of a task that has a due date but not a specific time of the day.  
To create a calendar entry, scroll to a date, and select Options > New entry. Select an entry type. Available settings for meeting,  
memo, anniversary, and to-do entries vary.  
Select from the following:  
Subject or Occasion Enter a description for the entry.  
Location Enter any necessary location information.  
Start time Enter the start time.  
End time Enter the end time.  
Start date or Date Enter the start date or date the event occurs.  
End date Enter the end date.  
Alarm — Set an alarm for meeting and anniversary entries. The alarm is displayed in the Day view.  
Repeat — Specify whether you want the entry to be repeated and when. Define the repeat type, frequency, and possible  
ending date.  
Synchronisation — If you select Private, the calendar entry can be seen only by you and is not shown to others with online  
access to view the calendar. If you select Public, the calendar entry is shown to others who have access to view your calendar  
online. If you select None, the calendar entry is not copied to your PC when you synchronize.  
Tip: Make sure you have selected the correct city in the Clock application, because scheduled calendar entries may  
change when the current city is changed and is on another time zone.  
To open and edit an existing entry, scroll to the entry, and select Options > Open. Edit the details in the various fields.  
Tip: When you edit or delete a repeated entry, choose how you want the change to take effect. If you select All calendar  
entries deleted, all repeated entries are deleted. If you select Delete entry, only the current entry is deleted.  
To-do  
You can create and maintain a task or list of tasks that must be done by a certain day. Each task can be assigned a due date, and  
an alarm.  
To open the list of to-do notes, select Options > To-do list.  
To add a to-do note, select Options > New entry > To-do. Start to write the task in the Subject field. You can set a due date for  
the task, create an alarm for it, and specify a priority. The priority icons are ( ! ) High and ( - ) Low. There is no icon for Normal.  
To mark a task as completed, scroll to the task in the to-do list, and select Options > Mark as done.  
To restore a task, scroll to it in the todo list, and select Options > Mark as not done.  
Calendar settings  
Select Options > Settings to modify the Calendar alarm tone, Default view, Week starts on, and Week view title.  
Copyright © 2006 Nokia. All Rights Reserved.  
77  
               
O r g a n i s e r  
Calendar views  
To switch between the different calendar views, select Options in any calendar view. Select a type of view from the list.  
Tip: When viewing Calendar in any view, press * to quickly switch to another view.  
To view the current day in the month view, press #.  
To set the default calendar view, select Options > Settings > Default view > Month view , Week view, Day view, or To-do view.  
To view a specific date in the calendar view, select Options > Go to date. Enter the date, and select OK.  
Tip: To quickly move to the nearest date with a scheduled event, press #.  
In the Month view, you can view the entire month at one time. Each row shows one week of dates. The active month is displayed,  
and the active day is either today or the last day that was viewed. The active day is marked with a colored square. Days that  
have scheduled events are marked with a small triangle in the bottom right corner. Scroll to switch between the days of the  
month and day entries.  
Tip: When viewing Calendar in any view, press * to quickly switch to another view.  
The Week view shows the events for the selected week in seven day boxes. Today's date is marked with a colored square. Memos  
and anniversaries are placed before 8:00 a.m.  
To change the starting day of the week, select Options > Settings > Week starts on.  
The Day view view shows the events for the selected day. Entries are grouped into time slots according to their starting time.  
To view the previous or next day, scroll left or right.  
The To-do view view shows the to-do items for the selected day.  
Send calendar entries  
To send a calendar entry to a compatible device, scroll the entry, and select Options > Send > Via text message, Via  
multimedia, Via e-mail, Via Bluetooth, or Via infrared.  
Add a received calendar entry to your calendar  
You can receive a calendar entry as an attachment to a multimedia or e-mail message.  
To add a received calendar entry to your calendar, open the calendar entry attachment in the message, and select Options >  
Save to Calendar. The entry is added to your default calendar.  
Notes  
Select Menu > Organiser > Notes.  
You can create and send notes to other compatible devices, and save plain text files (.txt format) that you receive to Notes.  
To write a new note, select Options > New note, write the text and press Done.  
In the Notes main view, the following options are available:  
Open Open the selected note.  
Send To send the selected note, select one of the sending methods.  
New note Create a new note.  
Delete Delete the selected note.  
Mark/Unmark — Select a note or multiple notes, and apply the same rule to each.  
Synchronisation — Select Start to initialize synchronization or Settings to define the synchronization settings for the note.  
When viewing a note, select Options > Find to search the note for a phone number, Internet telephone address, e-mail or Web  
address.  
Calculator  
Note: This calculator has limited accuracy and is designed for simple calculations.  
Select Menu > Organiser > Calculator.  
To make a calculation, enter the first number of the calculation. Scroll to and select a function such as add or subtract from the  
function map. Enter the second number of the calculation, and select =. To add a decimal point, press #.  
The calculator performs operations in the order they are entered. The result of the calculation remains in the editor field and  
can be used as the first number of a new calculation.  
To save the results of a calculation, select Options > Memory > Save. The saved result replaces the previously stored number in  
memory.  
Copyright © 2006 Nokia. All Rights Reserved.  
78  
                       
O r g a n i s e r  
To retrieve the results of a calculation from memory and use them in a calculation, select Options > Memory > Recall.  
To view the last saved result, select Options > Last result.  
Exiting the calculator application or turning off the device does not clear the memory. You can recall the last saved result the  
next time you open the calculator application.  
Converter  
Select Menu > Organiser > Converter.  
The converter has limited accuracy, and rounding errors may occur.  
Convert measurements  
1. Scroll to the Type field, and select Options > Conversion type to open a list of measures. Scroll to the measure you want to  
use, and select OK.  
2. Scroll to the first Unit field, and select Options > Select unit. Select the unit from which you want to convert, and select OK.  
Scroll to the next Unit field, and select the unit to which you want to convert.  
3. Scroll to the first Amount field, and enter the value you want to convert. The other Amount field changes automatically to  
show the converted value.  
Press # to add a decimal and * for + and - (for temperature), and E (exponent) symbols.  
Set base currency and exchange rate  
Note: When you change base currency, you must enter new exchange rates because all previously set exchange rates  
are cleared.  
Before you can make currency conversions, you must choose a base currency and add exchange rates. The rate of the base  
currency is always 1. The base currency determines the conversion rates of the other currencies.  
1. To set the rate of exchange for the unit of currency, scroll to the Type field, and select Options > Currency rates.  
2. A list of currencies opens, and you can see the current base currency at the top. Scroll to the currency type and enter the  
exchange rate you would like to set per single unit of currency.  
3. To change the base currency, scroll to the currency, and select Options > Set as base curr..  
4. Select Done > Yes to save the changes.  
After you have inserted all the necessary exchange rates, you can make currency conversions.  
Voice mailbox  
Select Menu > Organiser > Voice mail.  
When you open the voice mailbox application for the first time, you are asked to enter the number of your voice mailbox. To  
change the number, select Options > Change number. To call the number, select Options > Call voice mailbox.  
Tip: To call your voice mailbox (network service) in standby mode, press and hold 1, or press 1 then the call key.  
Clock  
Select Menu > Clock.  
Clock settings  
If the alarm time is reached while the device is switched off, the device switches itself on and starts sounding the alarm tone.  
If you select Stop, the device asks whether you want to activate the device for calls. Select No to switch off the device or Yes to  
make and receive calls. Do not select Yes when wireless phone use may cause interference or danger.  
Tip: To update date and time automatically (network service), select Tools > Settings > Network operator time > On.  
To change the clock type, select Options > Settings > Clock type > Analogue or Digital.  
To set an alarm, select Options > Set alarm. Enter the alarm time, and select OK.  
To view and change alarms, select Reset alarm.  
To remove an alarm, select Remove alarm.  
Date and time settings  
To change the date and time, their display formats, alarm tone, and to define whether you want to use automatic time update,  
select Options > Settings and from the following:  
Time Enter the time, and select OK.  
Copyright © 2006 Nokia. All Rights Reserved.  
79  
             
O r g a n i s e r  
Time zone Enter the time zone, and select OK.  
Date Enter the date, and select OK.  
Date format Change how the date is displayed. Scroll to the desired format, and select OK.  
Date separator Change the symbol that separates days, months, and years. Scroll to the symbol you want, and select OK.  
Time format — Select 24-hour or 12-hour.  
Time separator — Select the symbol that separates hours and minutes.  
Clock type — Select Analogue or Digital.  
Clock alarm tone — Select the tone that you want to use for the alarm clock.  
Network operator time Update time, date, and time zone information automatically (network service). Select Auto-  
update to activate. This service may not be available in all networks.  
Add and delete cities  
To add a city, scroll right, and select Options > Add city. Scroll to a city, and select Options > Select.  
Tip: To search for a city in the Cities list, select Options > Add city > Options > Find. Enter the city name in the search  
field.  
To delete a city, scroll right, scroll to the city, and select Options > Remove.  
Changing the home city may change the general system time of your device.  
Copyright © 2006 Nokia. All Rights Reserved.  
80  
 
13.  
Tools  
Select Menu > Tools.  
The Tools folder contains applications used to configure your device and to configure other applications.  
Positioning  
With the positioning service you can receive information from service providers about local issues such as weather or traffic  
conditions, based on the location of your device (network service).  
Select Menu > Tools > Positioning.  
To select a positioning method, scroll to the positioning method, and select Options > Enable. To stop using it, select Options >  
Disable. The Bluetooth positioning method enables you to use Bluetooth GPS enhancements for positioning. The Network  
based positioning method is provided by your network operator or service provider. Both positioning methods can be used  
simultaneously.  
Navigator  
This feature is not designed to support positioning requests for related calls. Contact your service provider for more information  
about how your phone complies with government regulations on location based emergency calling services.  
GPSshould not be used for precise location measurement, and you should never relysolelyon location data from the GPSreceiver.  
Select Menu > Tools > Navigator.  
Navigator is a GPS application that enables you to view your current location, find your way to a desired location, and track  
distance. The application requires a Bluetooth GPS accessory to operate. You must also have Bluetooth GPS positioning method  
enabled in Menu > Tools > Positioning.  
The application must receive positioning info from at least three satellites to use it as a traveling aid.  
The application requires a Bluetooth GPS accessory to operate.  
Select from the following:Navigator View navigating information to your trip destination. Position View positioning information  
about your current location. Trip dist. View your traveling information such as the distance and duration you have traveled and  
your average and maximum speeds.  
Navigation view  
The navigation view guides you to your trip destination. The cardinal points are indicated by letters on the circle, and the general  
direction to your destination by a deeper color.  
Select from the following: Set destination Select a landmark or location as the destination of your trip, or enter the destination  
latitude and longitude coordinates. Stop navigation Delete the destination set for your trip. Save position Save your current  
position as a location or landmark. Satellite status View the signal strength of the satellites that provide the positioning info  
necessary for navigation. Saved locations View the locations you have temporarily saved in your device to help in navigation.  
Position view  
View positioning info such as the latitude and longitude coordinates and altitude of your current location. You can also see the  
accuracy of this info.  
Select from the following: Save position Save your current position as a location or landmark. Satellite status View the signal  
strength of the satellites that provide the positioning info necessary for navigation. Saved locations View the locations you have  
temporarily saved in your device to help in navigation.  
Trip distance view  
The trip meter calculates the travelled distance and time and your average and maximum traveling speeds.  
Select from the following: Start Activate the trip meter. Stop End using the trip meter. The values calculated by it remain on the  
display. Resume Continue using the trip meter. Reset Set the values calculated by the trip meter to zero and start recalculating  
them from the start. Clear Empty the trip meter values after stopping its use. Save position Save your current position as a  
location or landmark. Satellite status View the signal strength of the satellites that provide the positioning info necessary for  
navigation. Saved locations View the locations you have temporarily saved in your device to help in navigation.  
Copyright © 2006 Nokia. All Rights Reserved.  
81  
               
T o o l s  
Manage locations  
Select Position > Options > Saved locations.  
You can temporarily save locations in your device to help in navigation.  
To save a location in Navigator, Position, or Trip dist. view, select Options > Save position.  
To save a temporary location as a more permanent landmark, select Options > Save as landmark.  
To delete a location, scroll to it, and press Options > Clear.  
Navigator settings  
Select Options > Settings.  
To change the measuring system in use, select Measurement system > Metric or Imperial.  
To enter the altitude calibration to correct the altitude received from the positioning satellites, select Altitude calibration.  
Landmarks  
Select Menu > Tools > Landmarks.  
Landmarks are coordinates to geographic locations that you can save to your device for later use in different location-based  
services. You can create landmarks using a Bluetooth GPS enhancement or network (network service). See "Navigator," p. 81.  
To create a landmark, select Options > New landmark. Select Current position to make a network request for the latitude and  
longitude coordinates of your current location or Enter manually to fill in the necessary location information such as a name,  
category, address, latitude, longitude and altitude.  
To view or edit a landmark, scroll to it, and press the joystick.  
To delete a landmark, scroll to it, and press the clear key.  
With each landmark, select Options and select from the following options:  
Add to category Organize the landmark to a group of similar landmarks. Scroll to the category, and press the joystick. To  
view your landmark categories, scroll right or left.  
Send — Send the landmark to compatible devices.  
Edit categories Add, edit, or delete the your landmark categories.  
Landmark icon Change the icon of the landmark. Scroll to the desired icon, and press the joystick.  
Landmark categories  
You can view landmark categories in two views: one lists categories that already contain landmarks, and the other lists all  
categories that your device has.  
To view categories that already contain landmarks, select Menu > Tools > Landmarks, and scroll right.  
To view the landmarks that a category contains, select the category, and press the joystick.  
To move a landmark from one category to another, scroll left. Scroll to a landmark, and press Options > Add to category. Scroll  
to the old category, and press the joystick to remove the mark next to it. Scroll to the category or categories to which you want  
to add the landmark, and press the joystick. Select Accept.  
With each landmark, select Options and select from the following options:  
Edit Modify landmark information such as a name, category, address, latitude, longitude and altitude.  
New landmark Create a landmark directly into the category. Select Current position to make a network request for the  
latitude and longitude coordinates of your current location or Enter manually to fill in the necessary location information  
such as a name, category, address, latitude, longitude and altitude.  
Add to category Organize the landmark to a group of similar landmarks. Scroll to the category, and press the joystick.  
Send — Send the landmark to compatible devices.  
Edit categories Add, edit, or delete the your landmark categories.  
Landmark icon Change the icon of the landmark. Scroll to the desired icon, and press the joystick.  
The available options may vary.  
Edit landmark categories  
Select Options > Edit categories.  
Select Options and select from the following options:  
New landmark Create a landmark directly into the category. Select Current position to make a network request for the  
latitude and longitude coordinates of your current location or Enter manually to fill in the necessary location information  
such as a name, category, address, latitude, longitude and altitude.  
Landmark icon Change the icon of the landmark. Scroll to the desired icon, and press the joystick.  
Copyright © 2006 Nokia. All Rights Reserved.  
82  
           
T o o l s  
To delete a landmark category that you have created, scroll to it and press the clear key. You cannot delete preset categories.  
Edit landmarks  
Select Options > Edit or New landmark > Enter manually. Enter location and other information such as a name, category, address,  
latitude, longitude and altitude.  
With each landmark, select Options and select from the following options:  
Select categories Organize the landmark to a group of similar landmarks. Scroll to the category and press the joystick to  
modify landmark information such as a name, category, address, latitude, longitude and altitude.  
Current position Request and automatically fill in the geographical latitude and longitude coordinates to make a landmark  
of your current location.  
Landmark icon Change the icon of the landmark. Scroll to the desired icon, and press the joystick.  
Send — Send the landmark to compatible devices.  
Available options may vary.  
Receive landmarks  
Select Menu > Messag.. Open a message that contains a landmark you have received from another device. Scroll to the landmark,  
and press the joystick.  
To save the landmark in your device, select Options > Save.  
To forward the landmark to compatible devices, select Options > Send.  
Voice commands  
Select Menu > Tools > Voice commands.  
Use voice commands to make phone calls and to launch applications, profiles, or other functions on the device.  
The device creates a voice tag for the entries in the contacts list and for the functions designated in the Voice commands  
application. When a voice command is spoken, the device compares the spoken words to the voice tag in the device.  
Voice commands are not dependent on a speakers voice; however, the voice recognition in the device adapts to the main users  
voice to better recognize voice commands.  
Use a voice command to make a call  
The voice tag for a contact is the name or nickname that is saved on the contact card in Contacts. To listen to the voice tag, open  
a contact card, and select Options > Playback.  
1. To make a call using a voice command, press and hold the voice key.  
2. When you hear the tone or see the visual display, clearly speak the name saved on the contact card.  
3. The device plays a synthesized voice tag for the recognized contact in the selected device language, and displays the name  
and number. After a timeout of 1.5 seconds, the device dials the number. If the recognized contact was not correct, select  
Next to view a list of other matches or Quit to cancel dialing.  
If several numbers are saved under the contact, the device selects the default number, if it has been set. Otherwise, the device  
selects the first available number of the following fields: Mobile, Mobile (home), Mobile (business), Telephone, Tel. (home), and  
Tel. (business).  
Use a voice command to launch an application  
The device creates voice tags for the applications listed in the Voice commands application.  
To launch an application using a voice command, press and hold the voice key, and clearly speak the voice command. If the  
recognized application was not correct, select Next to view a list of other matches or Quit to cancel.  
To add more applications to the list, select Options > New application.  
To change the voice command of an application, scroll to the application, and select Options > Change command. Type the new  
voice command, and select OK.  
Use voice commands for profiles  
The device creates a voice tag for each profile. To set on a profile using a voice command, press and hold the voice key, and say  
the name of the profile.  
To change the voice command, scroll to the desired profile, and select Profiles > Options > Change command.  
Copyright © 2006 Nokia. All Rights Reserved.  
83  
             
T o o l s  
Voice command settings  
To switch off the synthesizer that plays recognized voice commands in the selected device language, select Settings >  
Synthesiser > Off.  
To reset voice recognition learning when the main user of the device has changed, select Reset voice adapts..  
Voice aid  
Select Menu > Tools > Voice aid.  
The voice aid application reads text on the screen, allowing you to use basic functions of your device without looking at the  
display.  
Select from the following:  
Contacts Hear the entries in your contacts list. Do not use this option if you have more than 500 contacts.  
Recent calls Hear information on your missed and received calls, dialed numbers, and frequent calls.  
Voice mailbox Retrieve and listen to your voice messages.  
Dialler Dial a telephone number.  
Clock Hear the current time and date.  
To hear more options, select Options.  
Sett. wizard  
Sett. wizard configures your device for operator (MMS, GPRS, and Internet), e-mail, push-to-talk (network service), and video  
sharing (network service) settings based on your network operator information.  
To use these services, you may have to contact your network operator or service provider to activate a data connection or other  
services.  
To edit settings, select Menu > Tools > Sett. wizard and the item you want to configure.  
E-mail  
1. To edit e-mail settings, select Menu > Tools > Sett. wizard > E-mail. Sett. wizard detects your available network operators. If  
the device detects more than one network operators, select one and OK.  
If the network operator is not recognized, you must select Country/Region and Operator.  
2. Select your e-mail service provider from the list.  
3. Select the outgoing mail server. Use the default server if you are not sure.  
If Sett. wizard prompts you to enter the details of your E-mail address (including the domain name), User name, and  
Password, select each in turn and Options > Change. Enter the details, and select OK.  
1. Select Options > OK when you are finished.  
2. Select OK to confirm that you want to set up the mailbox for the specified operator.  
3. Select OK.  
To send or receive e-mail messages, you must have an active packet data account. Contact your network operator or service  
provider for details.  
Push to talk  
Push to talk (PTT) (network service) provides direct voice communication with the push of a key. With push to talk, you can use  
your device as a walkie-talkie.  
1. To edit Push to talk (PTT) (network service) settings, select Menu > Tools > Sett. wizard > Push to talk. Sett. wizard detects  
your available network operators. If the device detects more than one network operators, select one and OK.  
If the network operator is not recognized, you must select Country/Region and Operator.  
2. Some operators require a User name, Password, and Nickname. Select each in turn and Options > Change. Enter the details,  
and select OK.  
3. Select Options > OK when you are finished.  
4. Select OK to confirm that you want to set up PTT for the specified operator.  
To use push to talk, you must have an active packet data account. Contact your network operator or service provider for details.  
If an access point has not been set up for the selected operator, you are prompted to create a new one.  
Video sharing  
1. To edit Video sharing (network service) settings, select Menu > Tools > Sett. wizard > Video sharing. Sett. wizard detects your  
available network operators. If the device detects more than one network operators, select one and OK.  
Copyright © 2006 Nokia. All Rights Reserved.  
84  
             
T o o l s  
If the network operator is not recognized, you must select Country/Region and Operator.  
2. Some operators require a Video sharing address, a user name, and a password. Select each in turn and Options > Change.  
Enter the details, and select OK.  
3. Select Options > OK when you are finished.  
4. Select OK to confirm that you want to set up video sharing for the specified operator.  
5. After creating video sharing settings, Sett. wizard asks if you want to create or update your own contact. Select Yes or No.  
To use video sharing, you must have an active packet data account. Contact your network operator or service provider for details.  
Operator  
1. To edit operator settings (access points, Web browser, MMS, and streaming), select Menu > Tools > Sett. wizard > Operator.  
Sett. wizard detects your available network operators.  
2. If the device detects more than one network operators, select one and OK.  
3. If the network operator is not recognized, you must select Country/Region and Operator.  
If you are not able to use Sett. wizard, visit the Nokia phone settings Web site at www.nokia.com.  
Application manager  
Select Menu > Tools > Application manager.  
When you open the application manager, you see all the software packages that have been installed, with their name, version  
number, type, and size. You can view the details of installed applications, remove them from your device, and specify installation  
settings.  
Install applications and software  
Important: Only install applications from sources that offer adequate protection against harmful software.  
You can install two types of applications and software on your device:  
Applications and software specifically intended for your device or compatible with the Symbian operating system. These  
software installation files have the extension .sis.  
J2ME™ applications compatible with the Symbian operating system. The Java application installation file extensions are .jad  
or .jar.  
Installation files may be transferred to your device from a compatible computer, downloaded during browsing, or sent to you  
in a multimedia message, as an e-mail attachment, or with Bluetooth. If you use Nokia PC Suite to transfer a file to your device,  
save the file in the C:\nokia\installs folder in your device.  
During installation, the device checks the integrity of the package to be installed. The device shows information about the checks  
being carried out, and you are given options to continue or cancel the installation.  
If you install applications that require a network connection, note that the power consumption of your device may increase  
when you use these applications.  
View and remove software  
You can view the details of installed applications or remove them from your device.  
To view the details of an installed software package, select the application and Options > View details.  
To remove software, open the application manager main view and select Options > Remove.  
If you remove software, you can only reinstall it by using the original software package file, or by restoring a full backup that  
contains the removed software package. If you remove a software package, you may no longer be able to open files created  
with that software. Ifanother software package depends on the software package that you removed, the other software package  
may stop working. Refer to the documentation of the installed software package for details.  
View the installation log  
To view the installation log, select Options > View log. A list shows what software has been installed and removed, and the date  
of installation or removal. If you encounter problems with the device after installing a software package, you can use this list  
to find out which software package may be the cause of the problem. The information in this list may also help to pinpoint  
problems that are caused by software packages that are incompatible with each other.  
Settings  
To modify installation settings, select Options > Settings and from the following:  
Copyright © 2006 Nokia. All Rights Reserved.  
85  
                     
T o o l s  
Delete The software package installation file is deleted from the device after installation. If you download software  
packages using the Web browser, this may help to reduce the amount of storage space required. If you want to store the  
software package file for possible reinstallation, do not select this option, or make sure that you have a copy of the software  
package file stored on a compatible PC or on a CD-ROM.  
Select language: — If the software package contains several language versions of the software, select the language version  
that you want to install.  
Type — Specify what kind of applications you want installed. You may choose to install only applications with validated  
certificates. This setting applies only to Symbian operating system applications (.sis files).  
Specify Java application security settings  
To specify security settings for a Java application, select Options > Suite settings.  
You can define which functions the Java application can access. The value that you can set for each functionality depends on  
the protection domain of the software package.  
Network access Create a data connection to the network.  
Messaging — Send messages.  
App. auto-start Open the application automatically.  
Connectivity Activate a local data connection, such as a Bluetooth connectivity.  
Multimedia Take pictures or record videos or sound.  
Read user data Read your calendar entries, contacts, or any other personal data  
Edit user data Add personal data, such as entries to your address book.  
You can define how you will be prompted to confirm Java application access to device functions. Select one of the following  
values:  
Ask every time Require the Java application to ask for your confirmation each time it uses the functionality.  
Ask first time Require the Java application to ask for initial confirmation to use the functionality.  
Always allowed Allow the Java application to use the functionality without your confirmation.  
Not allowed — Prevent the Java application from using the functionality.  
The securitysettings help protect your device against harmfulJava applications that mayuse the functions ofyour device without  
your permission. Only select Always allowed if you know the supplier and trustworthiness of the application.  
Certificate manager  
Important: Note that even if the use of certificates makes the risks involved in remote connections and software  
installation considerably smaller, they must be used correctly in order to benefit from increased security. The existence  
of a certificate does not offer any protection by itself; the certificate manager must contain correct, authentic, or trusted  
certificates for increased securityto be available. Certificates have a restricted lifetime. IfExpired certificate or Certificate  
not valid yet is shown even if the certificate should be valid, check that the current date and time in your device are  
correct.  
Before changing any certificate settings, you must make sure that you really trust the owner of the certificate and that  
the certificate really belongs to the listed owner.  
Digital certificates are used to verify the origins of software but do not guarantee safety. There are three different types of  
certificates: authority certificates, personal certificates, and server certificates. During a secure connection, a server may send a  
server certificate to your device. Upon receipt, it is checked through an authority certificate stored on your device. You receive  
notification if the identity of the server is not authentic or if you do not have the correct certificate in your device.  
Download a certificate from a web site, or receive a certificate as an e-mail attachment, or as a message sent through a Bluetooth  
or infrared connection. Certificates should be used when you connect to an online bankor a remote server to transfer confidential  
information. They should also be used if you want to reduce the risk of viruses or other malicious software, and to check the  
authenticity of software when you download and install software to your device.  
Tip: When you add a new certificate, check its authenticity.  
Manage personal certificates  
Personal certificates are certificates that are issued to you.  
To add certificates to your device, select a certificate file and Save. To remove a selected certificate, select Options > Delete.  
To check the authenticity of a certificate, select a certificate and View details. Fingerprints uniquely identify a certificate. Contact  
the help desk or customer service of the owner of the certificate, and ask to compare fingerprints. Six-digit private key store  
passwords contain the secret keys that come with personal certificates.  
Manage authority certificates  
Authority certificates are used by some services to check the validity of other certificates.  
To add certificates to your device, select a certificate file and Save. To remove a selected certificate, select Options > Delete.  
Copyright © 2006 Nokia. All Rights Reserved.  
86  
           
T o o l s  
To check the authenticity of a certificate, select a certificate and View details. Fingerprints uniquely identify a certificate. Contact  
the help desk or customer service of the owner of the certificate, and ask to compare fingerprints. Six-digit private key store  
passwords contain the secret keys that come with personal certificates.  
Trusting a certificate means that you authorize it to verify web pages, e-mail servers, software packages, and other data. Only  
trusted certificates can be used to verify services and software.  
To change trust settings, select a certificate and Options > Trust settings. Select an application field and Yes or No. You cannot  
change the trust settings of a personal certificate.  
Depending on the certificate, a list of applications is displayed that can use the certificate:  
Symbian installation — New Symbian operating system application.  
Internet E-mail and graphics.  
App. installation — New Java application.  
Online certif. check Online certificate status protocol.  
View certificate details  
You can only be sure of the correct identity of a server when the signature and the period of validity of a server certificate have  
been checked.  
To view certificate details, select a certificate and View details.  
One of the following notes may appear:  
Certificate not trusted You have not set any application to use the certificate. You may want to change the trust settings.  
Expired certificate The period of validity has ended for the selected certificate.  
Certificate not valid yet The period of validity has not yet begun for the selected certificate.  
Certificate corrupted The certificate cannot be used. Contact the certificate issuer.  
Certificate security settings  
Select from the following:  
Software installation — Select to install signed applications only or all applications.  
Online certif. check To check the validity of certificates when an application is installed, select On.  
Default web address The validity of a certificate is checked from the default address if the certificate does not include its  
own Web address.  
Nokia Catalogs  
Select Menu > Catalogs. Select OK if you accept the disclaimer.  
Nokia Catalogs (network service) is a mobile content shop available on your device. With Nokia Catalogs you can discover,  
preview, buy, download, and upgrade content, such as games, ringing tones, wallpapers, services, and applications, for your  
device. The available content depends on your network operator and service provider.  
Nokia Catalogs uses your network services to access the most updated catalog content. For information on additional items  
available through Nokia Catalogs, contact your network operator or service provider.  
Nokia Catalogs receives ongoing updates, bringing you the latest content your network operator or service provider offers for  
your device. To update the catalogs manually, select Options > Refresh list.  
Open a catalog  
Select Menu > Catalogs.  
When you scroll to a catalog folder, a description of the contents is shown on the display.  
Select Options and select from the following:  
Open Open the selected catalog.  
View details View the catalog details.  
Hide Hide the selected catalog from the catalog list.  
Show all Bring the hidden catalogs back to the catalog list.  
Refresh list Download an updated catalog list.  
Application — Select About to see information about the application or Disclaimer to see the catalog provider's disclaimer.  
Homepage Open the Catalogs main view.  
Open a folder  
Select Menu > Catalogs.  
A catalog folder may contain several subfolders.  
Select Options and select from the following:  
Open Open the folder contents if you have purchased and downloaded the selected item.  
Copyright © 2006 Nokia. All Rights Reserved.  
87  
             
T o o l s  
Open Open the selected subfolder.  
View details View the catalog details.  
Preview — Show a preview of the selected item.  
Get Download the selected item if you have purchased it, but not yet downloaded it.  
Buy — Purchase the selected item.  
Set as wallpaper — If the selected item is a wallpaper, select this option to set is as the wallpaper for the device.  
Set as ringing tone — If the selected item is a ringing tone, select this option to set is as the ringing tone for the device.  
Set as theme — If the selected item is a theme, select this option to set is as the theme for the device.  
Online information Open a Web site with information on the selected item, if available.  
Purchase details Check the details of the purchased item.  
Refresh list Download an updated folder.  
Application — Select About to see information about the application or Disclaimer to see the catalog provider's disclaimer.  
Homepage Open the Catalogs main view.  
Catalogs settings  
Select Menu > Catalogs.  
From the catalogs main view, select Options and select from the following:  
Access point — Select a default access point to be used with the catalogs application.  
Automatic open — Select whether to open the downloaded application automatically .  
Preview confirmation — Select whether to have a confirmation note to pop up before downloading the preview of the item.  
Buy confirmation — Select whether to have a confirmation note to pop up before buying the item.  
Copyright © 2006 Nokia. All Rights Reserved.  
88  
 
14.  
Device manager  
Select Menu > Connectivity > Dev. mgr..  
Manage data and software on your device.  
Server profile settings  
To create a server profile, select Options > New server profile and select from the following options:  
Server name Enter a name for the configuration server.  
Server ID Enter the unique ID to identify the configuration server. Contact your service provider for correct settings.  
Server password Enter a password that identifies the server to your phone when the server starts a configuration session.  
Session mode — Select the connection type to use for connecting to the server.  
Access point — Select the access point to use for connecting to the server.  
Host address Enter the URL address of the server.  
Port Enter the port number of the server.  
User name and Password Enter your user name and password to identify your phone to the server when you start a  
configuration session.  
Allow configuration To be able to receive configuration settings from this server, select Yes.  
Auto-accept all reqs. To have your phone ask for confirmation before accepting configuration from this server, select No.  
To edit an existing server profile, select Options > Edit profile.  
Remote configuration network service  
Select Menu > Connectivity > Dev. mgr..  
You can connect to a server and receive configuration settings for your device. You may receive server profiles and different  
configuration settings from your network operator, service providers, and company information management department.  
Configuration settings may include connection and other settings used by different applications in your device. Available options  
may vary.  
The remote configuration connection is usually started by the server when the device settings need to be updated.  
Remote configuration settings  
In the Dev. mgr. main view, select Options and select from the following:  
Start configuration Connect to the server and receive configuration settings for your device.  
New server profile Create a new server profile.  
Edit profile Change the profile settings.  
Delete Remove the selected profile.  
Enable config. — Select to receive configuration settings from those servers for which you have a server profile and have  
allowed configuration.  
Disable config. — Select to stop receiving configuration settings from all servers for which you have a server profile.  
View log View the configuration log of the selected profile.  
Create a configuration profile  
To create a new configuration server profile, select Options > New server profile and select from the following settings. Ask your  
service provider for the correct values.  
Server name Enter a name for the configuration server.  
Server ID Enter the unique ID to identify the configuration server.  
Server password Enter a password to identify your device to the server.  
Session mode — Select the preferred connection type.  
Access point — Select the access point to use for the connection, or create a new access point. You can also choose to be  
asked for the access point every time you start a connection.  
Host address Enter the Web address of the configuration server.  
Port Enter the port number of the server.  
User name Enter your user ID for the configuration server.  
Password Enter your password for the configuration server.  
Allow configuration — Select Yes to allow the server to initiate a configuration session.  
Auto-accept all reqs. — Select Yes if you do not want the server to ask for your confirmation when it initiates a configuration  
session.  
Copyright © 2006 Nokia. All Rights Reserved.  
89  
                 
D e v i c e m a n a g e r  
Data synchronization  
Menu > Connectivity > Sync.  
Use Sync to synchronize your contacts, calendar, or notes with corresponding applications on a compatible computer or remote  
Internet server. Your synchronization settings are saved in a synchronization profile. The application uses SyncML technology  
for remote synchronization. For information on SyncML compatibility, contact the supplier of the applications with which you  
want to synchronize your device.  
The available applications you can synchronize may vary. Contact your service provider for more information.  
Tip: You may receive the synchronization settings as a message from your service provider.  
Create a synchronization profile  
To create a profile, select Options > New sync profile and select from the following options:  
Sync profile name Enter a name for the profile.  
Applications — Select the applications to synchronize with the profile.  
Connection settings — Specify the needed connection settings. Contact your service provider for information.  
To edit an existing profile, select Options > Edit sync profile.  
Synchronization profiles  
In the Sync main view, select Options and select from the following options:  
Synchronise — Synchronize the data included in the selected profile with a remote database.  
New sync profile Create a synchronization profile. You may want to create multiple synchronization profiles for an  
application to vary the data bearer in use or remote database with which you synchronize your device.  
View log View the added, updated, and deleted entries in the latest synchronization with the profile.  
Delete Remove the selected profile.  
Synchronization connection settings  
To create the connection settings of a new profile, select New sync profile > Connection settings and select from the following  
options:  
Server version — Select the SyncML version you can use with your server.  
Server ID Enter the server ID of your server. This setting is only available if you select 1.2 as the SyncML version.  
Data bearer — Select the data bearer to connect to the remote database during synchronization.  
Access point — Select the access point to use for the synchronization connection, or create a new access point. You can also  
choose to be asked for the access point every time you start synchronizing.  
Host address Enter the Web address of the server that contains the database with which you want to synchronize your  
device.  
Port Enter the port number of the remote database server.  
User name Enter your user name to identify your device to the server.  
Password Enter your password to identify your device to the server.  
Allow sync requests To allow synchronization to start from the remote database server, select Yes.  
Accept all sync reqs. To have your device ask for your confirmation before accepting synchronization from the server, select  
No.  
Network authentic. To authenticate your device to the network before synchronization, select Yes. Enter your network  
user name and network password.  
Define synchronization settings for Contacts  
To define the synchronization settings for the Contacts application, scroll to the desired profile, and select Options > Edit sync  
profile > Applications > Contacts > Edit and select from the following options:  
Include in sync — Select whether to synchronize your contacts directory with this synchronization profile.  
Remote database Enter the path to the database with which you synchronize your contacts directory.  
Local database — If you have more than one contacts directory in your device, select the one you want to synchronize with  
this synchronization profile.  
Synchronisation type — Select the direction of synchronization. Scroll to Normal to synchronize data from the device to  
remote database and back, To phone only to synchronize data from the remote database to your device, or To server only to  
synchronize data from your device to the remote database.  
Copyright © 2006 Nokia. All Rights Reserved.  
90  
           
D e v i c e m a n a g e r  
Define synchronization settings for Calendar  
To define the synchronization settings for the Calendar application, scroll to the desired profile, and select Options > Edit sync  
profile > Applications > Calendar > Edit and select from the following options:  
Include in sync — Select whether to synchronize your calendar with this synchronization profile.  
Remote database Enter the path to the database with which you synchronize your calendar.  
Local database — If you have more than one calendar in your device, select the one you want to synchronize with this  
synchronization profile.  
Synchronisation type — Select the direction of synchronization. Scroll to Normal to synchronize data from the device to  
remote database and back, To phone only to synchronize data from the remote database to your device, or To server only to  
synchronize data from your device to the remote database.  
Define synchronization settings for Notes  
To define the synchronization settings for the Notes application, scroll to the desired profile, and select Options > Edit sync  
profile > Applications > Notes > Edit and select from the following options:  
Include in sync — Select whether to synchronize your notes with this synchronization profile.  
Remote database Enter the path to the database with which you synchronize your notes.  
Local database — If you have more than one Notes application in your device, select the one you want to synchronize with  
this synchronization profile.  
Synchronisation type — Select the direction of synchronization. Scroll to Normal to synchronize data from the device to  
remote database and back, To phone only to synchronize data from the remote database to your device, or To server only to  
synchronize data from your device to the remote database.  
Copyright © 2006 Nokia. All Rights Reserved.  
91  
   
15.  
Personalization  
Profiles  
Warning: In the offline profile you cannot make or receive any calls, or use other features that require network  
coverage. Calls may still be possible to the official emergency number programmed into your device. To make calls,  
you must first activate the phone function by changing profiles. If the device has been locked, enter the lock code.  
Select Menu > Tools > Profiles.  
You can adjust and customize the ringing tones, alert tones, and other device tones for different events, environments, or caller  
groups.  
To customize a profile, scroll to the desired profile in the list, and select Options > Personalise.  
Define the following settings:  
Ringing tone — Select a ringing tone from the list, or select Tone downloads to open a bookmark folder containing a list of  
bookmarks for downloading tones using the browser. To listen to the selected tone, select Play. If you have two alternate  
phone lines in use, you can specify a ringing tone for each line.  
Video call tone — Select a ringing tone for video calls.  
Say caller's name Activate the text-to-speech ringing tone feature. When someone from your contacts list calls you, the  
device sounds a ringing tone that is a combination of the spoken name of the contact and the selected ringing tone.  
Ringing type — Select how you want the ringing tone to alert.  
Ringing volume — Select the volume level of the ringing tone.  
Message alert tone — Select a tone for received text messages.  
E-mail alert tone — Select a tone for received e-mail messages.  
IM alert tone — Select a tone for received instant messages.  
Vibrating alert — Select whether you want the device to vibrate when you receive a call.  
Keypad tones — Set the volume level of the device keypad tones.  
Warning tones — Set the warning tones on or off.  
Alert for You can set the device to ring only upon calls from phone numbers that belong to a selected contact group. Phone  
calls coming from outside that group have a silent alert.  
Profile name You can give a name to a new profile or rename an existing profile. The General and Offline profiles cannot  
be renamed.  
The Offline profile prevents your device from accidentally switching on or sending or receiving messages; it also closes any  
Internet connection that may be in operation when the profile is selected. The Offline profile does not prevent you from  
establishing a wireless LAN or Bluetooth connection at a later time, so comply with any applicable safety requirements when  
establishing and using wireless LAN and Bluetooth connections.  
To change a profile, scroll to the desired profile in the list, and select Options > Activate.If you select the Offline profile, you  
cannot send or receive messages. However, you can establish a WLAN connection to read your e-mails or use Bluetooth at a  
later time, so comply with any applicable safety requirements when establishing and using wireless LAN and Bluetooth  
connections.  
To create a new profile, select Options > Create new, and define the settings.  
Select ringing tones  
To set a ringing tone, scroll to a profile, and select Options > Personalise > Ringing tone. Select a ringing tone from the list or  
select Tone downloads to open a bookmark folder containing a list of bookmarks for downloading tones using the browser.  
Any downloaded tones are saved to Gallery.  
To play the ringing tone for a selected contact group only, scroll to a profile, and select Options > Personalise > Alert for, and  
select the desired group. Phone calls coming from outside that group have a silent alert.  
To browse for a message tone, scroll to a profile and select Options > Personalise > Message alert tone.  
To listen to the selected tone, select the tone from the list and wait for the tone to play.  
Change enhancement settings  
Scroll to an enhancement, and select Options > Open.  
Change the default profile for the enhancement.  
To change enhancement settings, select an enhancement and Options > Open.  
Themes  
Select Menu > Tools > Themes.  
Copyright © 2006 Nokia. All Rights Reserved.  
92  
             
P e r s o n a l i z a t i o n  
You can change the look of the display of your device.  
To change the look of the display, highlight the theme you want to use, and select Options > Apply.  
To edit a theme, highlight the theme you want to edit, and select Options > Edit. Select Wallpaper to change the background  
image in the standby modes, or Power saver to use a text or the date and time as a power saver that appears on the display  
when no key presses have been made for a some time.  
To download themes, you need to establish a network connection that allows you to download themes from Internet sources  
that are compatible with your device.  
To download a theme, select Theme downloads. Enter the link from which you want to download your theme. Once the theme  
is downloaded you can preview, activate, or edit it.  
To preview a theme, highlight the theme you want to preview, and select Options > Preview. Select Apply to start using the  
new theme.  
Copyright © 2006 Nokia. All Rights Reserved.  
93  
16.  
Shortcuts  
Here are some of the available keyboard shortcuts in your device. Shortcuts can make the use of the applications more efficient.  
Some shortcuts are application-specific and they are not available for all applications.  
Active standby mode  
Left selection key + *  
Lock and unlock the keypad.  
Call key  
Open the call log.  
0
Press and hold to open your home page in the Web browser.  
Press and hold to switch between the Silent and General profiles.  
Press and hold to call your voice mailbox.  
#
1
Number key (2–9)  
Call a phone number using speed dialling. You must first activate speed dialling  
(Menu > Tools > Settings > Call > Speed dialling > On).  
Fold open  
Shift + joystick  
Ctrl+X  
Press and hold the Shift key and scroll left or right with the joystick to select text.  
Cut text.  
Ctrl+C  
Copy text.  
Ctrl+V  
Paste text.  
Chr + Shift  
Change the writing language.  
Fold closed  
Edit key + joystick  
#
Press and hold the Edit key and scroll left, right, up or down with the joystick.  
Press to switch between the different text cases. Press twice quickly to set the  
predictive text input on and off.  
#
Press and hold to switch between letter and number mode.  
Number keys (0–9)  
When writing text, press and hold a number key to insert a number.  
Image viewer  
Call key  
Send the image.  
0
5
7
4
6
2
8
3
1
*
Zoom out.  
Zoom in.  
Zoom in. Press twice for the full screen size.  
Scroll left in the zoomed image.  
Scroll right in the zoomed image.  
Scroll up in the zoomed image.  
Scroll down in the zoomed image.  
Rotate clockwise.  
Rotate counterclockwise.  
Switch between the full screen size and normal view.  
Copyright © 2006 Nokia. All Rights Reserved.  
94  
   
Battery information  
Your device is powered by a rechargeable battery. The full performance of a new battery is achieved only after two or three  
complete charge and discharge cycles. The battery can be charged and discharged hundreds of times, but it will eventually wear  
out. When the talk and standby times are noticeably shorter than normal, buy a new battery. Use only Nokia approved batteries,  
and recharge your battery only with Nokia approved chargers designated for this device.  
Unplug the charger from the electrical plug and the device when not in use. Do not leave fully charged battery connected to a  
charger, since overcharging may shorten its lifetime. If left unused, a fully charged battery will lose its charge over time.  
If the battery is completely discharged, it may take a few minutes before the charging indicator appears on the display or before  
any calls can be made.  
Use the battery only for its intended purpose. Never use any charger or battery that is damaged.  
Do not short-circuit the battery. Accidental short-circuiting can occur when a metallic object such as a coin, clip, or pen causes  
direct connection of the positive (+) and negative (-) terminals of the battery. (These look like metal strips on the battery.) This  
might happen, for example, when you carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage  
the battery or the connecting object.  
Leaving the battery in hot or cold places, such as in a closed car in summer or winter conditions, will reduce the capacity and  
lifetime of the battery. Always try to keep the battery between 15°C and 25°C (59°F and 77°F). A device with a hot or cold battery  
may not work temporarily, even when the battery is fully charged. Battery performance is particularly limited in temperatures  
well below freezing.  
Do not dispose of batteries in a fire as they may explode. Batteries may also explode if damaged. Dispose of batteries according  
to local regulations. Please recycle when possible. Do not dispose as household waste.  
Nokia battery authentication guidelines  
Always use original Nokia batteries for your safety. To check that you are getting an original Nokia battery, purchase it from an  
authorized Nokia dealer, look for the Nokia Original Enhancements logo on the packaging, and inspect the hologram label using  
the following steps:  
Successful completion of the four steps is not a total assurance of the authenticity of the battery. If you have any reason to  
believe that your battery is not an authentic original Nokia battery, you should refrain from using it, and take it to the nearest  
authorized Nokia service point or dealer for assistance. Your authorized Nokia service point or dealer will inspect the battery  
for authenticity. If authenticity cannot be verified, return the battery to the place of purchase.  
Authenticate hologram  
1. When looking at the hologram on the label, you should see the Nokia connecting hands symbol from one  
angle and the Nokia Original Enhancements logo when looking from another angle.  
2. When you angle the hologram left, right, down, and up, you should see 1, 2, 3, and 4 dots on each side  
respectively.  
3. Scratch the side of the label to reveal a 20-digit code, for example, 12345678919876543210. Turn the  
battery so that the numbers are facing upwards. The 20-digit code reads starting from the number at the  
top row followed by the bottom row.  
4. Confirm that the 20-digit code is valid by following the instructions at www.nokia.com/batterycheck.  
To create a text message enter the 20-digit code, for example, 12345678919876543210, and send to +44 7786  
200276.  
National and international operator charges will apply.  
You should receive a message indicating whether the code can be authenticated.  
Copyright © 2006 Nokia. All Rights Reserved.  
95  
     
B a t t e r y i n f o r m a t i o n  
What if your battery is not authentic?  
If you cannot confirm that your Nokia battery with the hologram on the label is an authentic Nokia battery, please do not use  
the battery. Take it to the nearest authorized Nokia service point or dealer for assistance. The use of a battery that is not approved  
by the manufacturer may be dangerous and may result in poor performance and damage to your device and its enhancements.  
It may also invalidate any approval or warranty applying to the device.  
To find out more about original Nokia batteries, visit www.nokia.com/battery.  
Copyright © 2006 Nokia. All Rights Reserved.  
96  
 
Care and maintenance  
Your device is a product of superior design and craftsmanship and should be treated with care. The suggestions below will help  
you protect your warranty coverage.  
Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode  
electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing  
it.  
Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged.  
Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp  
or melt certain plastics.  
Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device  
and damage electronic circuit boards.  
Do not attempt to open the device other than as instructed in this guide.  
Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.  
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.  
Do not paint the device. Paint can clog the moving parts and prevent proper operation.  
Use a soft, clean, dry cloth to clean any lenses, such as camera, proximity sensor, and light sensor lenses.  
Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or attachments could  
damage the device and may violate regulations governing radio devices.  
Use chargers indoors.  
Always create a backup of data you want to keep, such as contacts and calendar notes, before sending your device to a service  
facility.  
All of the above suggestions apply equally to your device, battery, charger, or any enhancement. If any device is not working  
properly, take it to the nearest authorized service facility for service.  
Copyright © 2006 Nokia. All Rights Reserved.  
97  
 
Additional safety information  
Operating environment  
Remember to follow any special regulations in force in any area, and always switch off your device when its use is prohibited  
or when it may cause interference or danger. Use the device only in its normal operating positions. This device meets RF exposure  
guidelines when used either in the normal use position against the ear or when positioned at least 1.5 centimeters (5/8 inches)  
away from the body. When a carry case, belt clip or holder is used for body-worn operation, it should not contain metal and  
should position the device the above-stated distance from your body.  
To transmit data files or messages, this device requires a quality connection to the network. In some cases, transmission of data  
files or messages may be delayed until such a connection is available. Ensure that the above separation distance instructions  
are followed until the transmission is completed.  
Parts of the device are magnetic. Metallic materials may be attracted to the device. Do not place credit cards or other magnetic  
storage media near the device, because information stored on them may be erased.  
Medical devices  
Operation of any radio transmitting equipment, including wireless phones, may interfere with the functionality of inadequately  
protected medical devices. Consult a physician or the manufacturer of the medical device to determine if they are adequately  
shielded from externalRFenergyor ifyou have anyquestions. Switch offyour device in health care facilities when anyregulations  
posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive  
to external RF energy.  
Pacemakers  
Pacemaker manufacturers recommend that a minimum separation of 15.3 centimeters (6 inches) be maintained between a  
wireless phone and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent  
with the independent research by and recommendations of Wireless Technology Research. Persons with pacemakers should  
do the following:  
Always keep the device more than 15.3 centimeters (6 inches) from the pacemaker  
Not carry the device in a breast pocket  
Hold the device to the ear opposite the pacemaker to minimize the potential for interference.  
If you suspect interference, switch off your device, and move the device away.  
Hearing aids  
Some digital wireless devices may interfere with some hearing aids. If interference occurs, consult your service provider.  
Vehicles  
RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel  
injection systems, electronic antiskid (antilock) braking systems, electronic speed control systems, and air bag systems. For more  
information, check with the manufacturer, or its representative, of your vehicle or any equipment that has been added.  
Only qualified personnel should service the device, or install the device in a vehicle. Faulty installation or service may be  
dangerous and may invalidate any warranty that may apply to the device. Check regularly that all wireless device equipment  
in your vehicle is mounted and operating properly. Do not store or carry flammable liquids, gases, or explosive materials in the  
same compartment as the device, its parts, or enhancements. For vehicles equipped with an air bag, remember that air bags  
inflate with great force. Do not place objects, including installed or portable wireless equipment in the area over the air bag or  
in the air bag deployment area. If in-vehicle wireless equipment is improperly installed, and the air bag inflates, serious injury  
could result.  
Using your device while flying in aircraft is prohibited. Switch off your device before boarding an aircraft. The use of wireless  
teledevices in an aircraft may be dangerous to the operation of the aircraft, disrupt the wireless telephone network, and may  
be illegal.  
Potentially explosive environments  
Switch off your device when in any area with a potentially explosive atmosphere, and obey all signs and instructions. Potentially  
explosive atmospheres include areas where you would normally be advised to turn off your vehicle engine. Sparks in such areas  
could cause an explosion or fire resulting in bodily injury or even death. Switch off the device at refueling points such as near  
gas pumps at service stations. Observe restrictions on the use of radio equipment in fuel depots, storage, and distribution areas;  
chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not  
always, clearly marked. They include below deck on boats, chemical transfer or storage facilities, vehicles using liquefied  
Copyright © 2006 Nokia. All Rights Reserved.  
98  
             
A d d i t i o n a l s a f e t y i n f o r m a t i o n  
petroleum gas (such as propane or butane), and areas where the air contains chemicals or particles such as grain, dust, or metal  
powders.  
Emergency calls  
Important: Wireless phones, including this device, operate using radio signals, wireless networks, landline networks,  
and user-programmed functions. Because of this, connections in all conditions cannot be guaranteed. You should never  
rely solely on any wireless device for essential communications like medical emergencies.  
To make an emergency call:  
1. If the device is not on, switch it on. Check for adequate signal strength.  
Some networks may require that a valid SIM card is properly inserted in the device.  
2. Press the end key as many times as needed to clear the display and ready the device for calls.  
3. Enter the official emergency number for your present location. Emergency numbers vary by location.  
4. Press the call key.  
If certain features are in use, you may first need to turn those features off before you can make an emergency call. Consult this  
guide or your service provider for more information.  
When making an emergency call, give all the necessary information as accurately as possible. Your wireless device may be the  
only means of communication at the scene of an accident. Do not end the call until given permission to do so.  
CERTIFICATION INFORMATION (SAR)  
THIS MOBILE DEVICE MEETS GUIDELINES FOR EXPOSURE TO RADIO WAVES.  
Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves  
recommended by international guidelines. These guidelines were developed by the independent scientific organization ICNIRP  
and include safety margins designed to assure the protection of all persons, regardless of age and health.  
The exposure guidelines for mobile devices employ a unit of measurement known as the Specific Absorption Rate or SAR. The  
SAR limit stated in the ICNIRP guidelines is 2.0 watts/kilogram (W/kg) averaged over 10 grams of tissue. Tests for SAR are  
conducted using standard operating positions with the device transmitting at its highest certified power level in all tested  
frequency bands. The actual SAR level of an operating device can be below the maximum value because the device is designed  
to use only the power required to reach the network. That amount changes depending on a number of factors such as how  
close you are to a network base station. The highest SAR value under the ICNIRP guidelines for use of the device at the ear is  
1.01 W/kg.  
Use of device accessories and enhancements may result in different SAR values. SAR values may vary depending on national  
reporting and testing requirements and the network band. Additional SAR information may be provided under product  
Copyright © 2006 Nokia. All Rights Reserved.  
99  
   
Index  
connections  
A
data call settings 43  
GPRS settings 44  
WLAN settings 44, 74  
contact groups 28  
contact information 28  
contacts  
access points 43, 72  
ad hoc network 49  
answering calls 21  
application manager 85  
applications  
common actions 20  
installing 85  
modifying installations 85  
removing 85  
adding 28  
copying information 28  
default information 28  
groups 28  
viewing the installation log 85  
attachments 35, 37  
audio files 57  
ringing tones 29  
copying text 15  
authority certificates 86  
automatic answer 76  
D
data  
connections 48  
synchronizing 90  
data and software management 89  
day view in calendar 78  
declining calls 21  
device manager 89  
display  
indicators 14  
settings 71  
diverting calls 22  
documents 63  
DTMF tones 22  
B
barring calls 22  
barring password 26  
battery  
charge level 14  
charging  
installing  
blogs 54  
Bluetooth  
connections 46  
pairing 47  
settings 46  
bookmarks 53  
browsing Web pages 53, 55  
business cards 29  
E
e-mail  
accounts 38  
messages 36  
replying 37  
writing 38  
C
cable 45  
calculator 78  
calendar 77  
calling 21  
email data roaming 51  
ending network connections 49  
enhancement settings 76  
equalizer 59  
calls  
barring 22  
diverting 22  
settings 71  
camera 61  
recording a video clip 61  
taking a picture 61  
CD-ROM 17  
F
feeds 54  
file manager 63  
flash player 60  
fold 10  
cells 66  
certificate details 87  
certificates 86  
charging the battery  
chart sheets 67  
chat 39  
G
gallery 56  
general packet radio service  
See GPRS  
GPRS  
access point settings 44  
counters 23  
general 48  
clock 79  
connecting to the Internet 43  
connection manager 49  
connection methods  
Bluetooth 46  
settings 73  
H
cable 45  
infrared 48  
modem 50  
help 19  
I
WLAN 49  
Copyright © 2006 Nokia. All Rights Reserved.  
100  
 
I n d e x  
images  
replying to 34  
sending 33  
add to contacts 56  
set as wallpaper 56  
zooming in or out 56  
settings 35  
music player 58  
inbox 30  
indicators 14  
infrared 48  
infrared port 12  
installing  
N
navigation 81  
net calls 25  
network settings 76  
notes 78  
applications 85  
battery  
SIM card  
instant messaging 39  
Internet 53  
O
outbox 31  
outline view 64, 65  
access points 43  
net call settings 72  
settings 43  
P
packet data  
access point settings 44  
counters 23  
IP passthrough 45  
general 48  
settings 73  
pairing 47  
personal certificates 86  
personalization 92  
phone  
J
Java applications 85, 86  
joystick 11, 71  
K
keyboard 10  
keyguard 12  
keypad lock 12  
calls 21  
language 71  
settings 71  
L
video calls 23  
photos 61  
picture messages 33  
playing  
landmarks 82  
language 71  
listening to music 58  
locking  
music 58  
device 12  
keypad 12  
logs 23, 85  
video and audio 57  
voice recordings 60  
Pop-Port connector 12  
predictive text input 15, 71  
presentations 67  
printing 70  
M
mail  
See e-mail  
profiles 92  
media applications 56  
memory 16  
R
on-device 16  
memory card 16  
passwords 17  
menu 19  
RealPlayer  
playing media clips 57  
settings 58  
recording  
messages  
calls 59  
deleting 37  
e-mail 36  
video clips 61  
voice 59  
folders 30  
rejecting calls 21  
remote configuration  
creating a profile 89  
settings 89  
multimedia messages 33  
picture messages 33  
sending 31  
special messages 42  
text messages 32  
miniSD card 16  
mobile VPN  
remote synchronization 90  
ringing tones 29  
roaming settings 51  
S
See VPN  
screen export 69  
security  
modem 50  
month view in calendar 78  
multimedia messages  
attachments 35  
creating 33  
device 26  
Java application 86  
memory card 17  
selecting text and objects 19  
receiving 34  
Copyright © 2006 Nokia. All Rights Reserved.  
101  
I n d e x  
selection key settings 71  
service commands 42  
settings  
text phone 76  
themes 92  
to-do list 77  
Bluetooth 46  
calendar 77, 78  
calls 71  
to-do view in calendar 78  
tools folder 81  
track lists 59  
connection 72  
display 71  
traditional text input 15  
TTY 76  
email data roaming 51  
general 71  
Internet 43  
IP passthrough 45  
Java application security 86  
message centers 31  
multimedia messages 35  
network 76  
profiles 92  
remote configuration 89  
security 26  
server profile 89  
standby 71  
text messages 33  
text phone 76  
trust 87  
tutorial 19  
U
USB data cable 45  
V
video calls 23  
video clips 57, 61  
virtual private network 50  
voice commands 83  
voice dialing 83  
voice mailbox 21  
voice memos 59  
voice over IP 25  
voice recorder 59  
volume 15, 59  
VPN 50  
TTY 76  
Web 54  
WLAN 74  
W
Web 53  
week view in calendar 78  
welcome note 71  
WLAN  
SettingWizard 84  
shortcuts 13, 94  
signal strength 14  
SIM access profile 48  
SIM card  
access point settings 44  
advanced access point settings 45  
general 49  
security settings 75  
settings 74  
installing  
text messages 32  
slide shows 67  
SMS messages 32  
SMTP settings 51  
software  
worksheets 65  
writing language 71  
installing 85  
removing 85  
special messages 42  
speed dialing 21  
standby  
mode 13  
settings 71  
storage 16  
switching device on and off  
Symbian applications 85  
synchronizing 90  
T
text  
copying 15  
predictive input 15  
selecting 19  
traditional input 15  
writing 15  
text messages  
editing message centers 31  
managing messages in the SIM card 32  
replying 32  
sending 32  
writing 32  
Copyright © 2006 Nokia. All Rights Reserved.  
102  

Verizon Communications Cell Phone DROID RAZR User Manual
Sony SCD C2000ES User Manual
Sony CD R Drive Unit CDU948S User Manual (1)
Sony CDP XE220 User Manual
Samsung Galaxy Tab 3 GTP5210ZWYXAR User Manual
Samsung Cell Phone SCHR355C User Manual
Samsung 840 Pro 256 Gb 25" Internal Solid State Drive MZ7PD256Z User Manual
Roberts Radio Swallow CD9959 User Manual
Philips MT3120 User Manual
Omega USB 4750 User Manual