iHome iH120 User Manual

Model iH120  
Alarm Clock For Your iPod  
Now Playing  
Table of Contents  
1
2
3
3
4
Quick Start  
Controls and Indicators  
iH120 Display  
Install Clock Backup Battery  
Using The Remote Control Unit  
Install/Replace the Remote Control Battery  
To check for iPod compatibility  
5
Setting Up the iH120  
Setting Time and Calendar  
6
6
Using the Alarm  
Charging your iPod  
Listening to iPod  
7
7
Listening to non-docking iPod or other portable audio devices  
Dimmer Operation  
7
8
Sleep Operation  
8
Click Sound Operation  
9
A Consumer Guide to Product Safety  
Trouble Shooting  
10  
11  
12  
Solución De Problemas  
Warranty Information  
A Consumer Guide to Product Safety  
This device complies with Part 15 of the FCC Rules, operation is subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  
This equipment complies with the limits for a Class B digital device as specified in Part 15 of FCC Rules. These limits  
provide reasonable protection against radio and TV interference in a residential area.  
However, your equipment might cause TV or radio interference even when it is operating properly. To eliminate interference  
you can try one or more of the following corrective measures:  
Reorient or relocate the receiving antenna.  
Increase the distance between the equipment and the radio or TV.  
Use outlets on different electrical circuits for the equipment and the radio or TV.  
Consult your dealer or an experienced radio/television technician if the problem still exists.  
Modifying or tampering with your systems internal components can cause a malfunction and might invalidate the systems  
warranty and void your FCC authorization to operate it.  
This Class B digital apparatus complies with Canadian ICES-003.  
Maintenance  
• Place the unit on a level surface away from sources of direct sunlight or excessive heat.  
• Protect your furniture when placing your unit on a natural wood and lacquered finish. A cloth or other protective material  
should be placed between it and the furniture.  
• Clean your unit with a soft cloth moistened only with mild soap and water. Stronger cleaning agents, such as Benzene,  
thinner or similar materials can damage the surface of the unit.  
Quick Start  
3:iPod  
1:power  
2:inserts  
Select the dock insert for your  
iPod model from the table below  
and place insert in dock.  
Never dock an iPod without  
an insert in place.  
Attach AC adaptor cable to DC jack  
on back of the iH120 and plug the  
other end into a wall socket.  
Insert iPod into dock with proper insert  
(iPod must not be in a skin or case).  
iPod will charge while docked. Press the  
Play Button on the iH120 to play iPod.  
thin iPod with video (30 GB)  
iPod touch 2G  
nano 4G  
insert 17  
Use this insert  
For this iPod  
Insert 9  
insert 16  
thin (30 GB) iPod with video  
thin (80/120 GB) iPod classic  
iPod touch 2G  
nano 4G  
NOTE: If you do not have an insert for your iPhone/iPod,  
800-288-2792 to purchase one.  
iH120 Display  
Alarm 1 Indicator  
iPod Indicator  
Wake-to Indicator  
Alarm 2 Indicator  
Daylight Saving Time  
Indicator  
Battery Low Indicator  
PM Indicator  
Wake-to Buzzer Indicator  
Time Display  
(PM) Alarm Time Indicator  
Sleep Indicator  
Alarm Time Indicator  
Install Clock Backup Batteries  
The iH120 uses 2 alkaline “AA” batteries to provide continuous alarm operation  
and clock settings in the event of a power failure. If the backup batteries have  
been installed and a power failure occurs or the AC cord is accidentally discon-  
nected, the display backlight will not remain lit, but current time and alarm time  
settings will be temporarily maintained. Otherwise, you must reset the time and  
alarm settings.  
1. Please make sure the AC adaptor is connected. Otherwise all settings may  
be lost during battery replacement.  
2. Open backup battery compartment door located on the bottom of the unit.  
3. Insert 2 AA batteries, checking that the polarity (+ and – ends of the battery)  
matches the drawing near the battery compartment. Close the compart-  
ment door.  
Installing Backup Batteries  
Note: Make sure you dispose of batteries properly (see your local regulations).  
3
Using the Optional Remote Control  
Power Button turns unit OFF or Reset Alarm.  
Volume Buttons raise and lower volume on the unit.  
Pressing FWD/REW while iPod is inserted will FWD/REV to next/previous track  
Pressing and holding FWD/REW while iPod is docked will scan forward/reverse  
within currently playing track.  
Pressing Play/Pause from power off mode will play iPod.  
Pressing Play/Pause while iPod is docked and playing will pause iPod.  
Press again to resume play.  
Pressing the sleep mode function same as on main unit.  
Pressing the mute button will mute unit.  
Remote not included  
with all iH120  
models.  
To order a remote,  
please visit  
Pressing the snooze/dimmer mode function same as on main unit.  
Install/Replace the Remote Control Battery  
Install/Replace the Remote Control Battery  
The remote control battery is already installed at the factory. When the  
remote control stops operating or its range seems reduced, it is time  
to replace the battery with a new one.  
1. The battery door is located on the back end of the remote control.  
2. Pull the battery door to release the battery door latch and take out  
the battery.  
3. Insert a CR2032 battery, checking that the + and – sides of the  
battery matches the drawing inside the battery compartment.  
4. Replace the battery door.  
Installing Remote Battery  
Note: Make sure you dispose of batteries properly (see your local regulations).  
The Remote Control controls basic functions on the iH120 and certain iPod functions when the iPod is docked in the iH120.  
For best results, aim remote control towards the remote sensor on the upper left corner of the unit.  
To check for iPod compatibility  
iH120 is an advanced system and supports most updated iPod features. To ensure your iPod works properly with the iH120,  
please update your iPod firmware with the latest version, available via iTunes.  
4
Setting Up the iH120  
This unit is a PRESET Clock: the clock is preset for the correct Eastern Standard Time at the factory. Please follow the steps  
below to match settings to your location.  
1. Depending on your location and whether or not Daylight Saving Time (DST) is in effect, set the DST Switch located on  
the back of the unit to +1 to add 1 hour or to -1 to subtract 1 hour. When set to +1 a DST icon will appear on the display,  
indicating DST mode.  
2. Press and hold the Time Zone Button located on the back of the unit until the current time zone at the lower part of the  
display blinks. If needed, press the  
or  
Button to select your time zone.  
3. Press the Time Zone Button again (or no button within 10 seconds) to exit the setting mode.  
4. If the time showing is not correct, please see Setting Time and Calendar to set the clock.  
Setting Time and Calendar  
1. Press and hold the Clock Adj Button located on the back of the unit until the time display blinks. Press the  
or  
Button until the current time is displayed. Holding the button for a few seconds will advance or reverse rapidly. Remem-  
ber to set the correct AM or PM. An icon in the upper right hand corner of the time digits is the PM Indicator; there is  
no AM indicator.  
2. Press the Clock Adj Button again to accept the current time setting and set current year. Press the  
or  
Button  
until the current year is displayed. Press the Clock Adj Button to confirm year setting after adjustment.  
3. The display will change to show the date blinking. Press the  
the button for a few seconds will advance or reverse rapidly.  
or  
Button until the current date is displayed. Holding  
4. Press the Clock Adj Button again (or if no button is pressed within 10 seconds) to exit the time and date setting mode.  
Two beeps will confirm clock setting is completed.  
5
Using the Alarms  
Setting the Alarms  
1. Press and hold the or Button until the alarm icon and alarm time blink. Press the  
or  
Button to set the  
alarm time. Holding the button for a few seconds will advance or reverse rapidly.  
Remember to set the correct AM or PM time.  
2. Press the Wake-to Button to select iPod or Buzzer alarm source. You can set different alarm sources for each alarm.  
The wake to icon will blink for 5 seconds, followed by the alarm icon and time.  
3. Press the Alarm Button again or wait for 5 seconds. Alarm is now armed, indicated by the numbered alarm clock icon.  
Review, Arming and Disarming Alarm (Turn Alarm Function On and Off)  
1. Press the or  
Button once. The unit will show the alarm time on the bottom part of the display for alarm time review.  
2. During alarm review, press the  
alarm icon appears in display.  
or  
button again to arm or disarm the alarm. When the alarm is armed, the related  
Resetting the Alarm to Come on the Next Day  
1. When the alarm is sounding, press the  
same time.  
Button to stop the alarm and reset it to come on the following day at the  
Snooze  
1. Press the Snooze/Dimmer Button after the alarm sounds. The alarm will be silenced and come on again 9 minutes  
later. Snooze can be press several times during the 1 hour alarm cycle.  
Sure Alarm  
The iH120 has a sure alarm feature. If backup batteries are installed (see page 3) the buzzer alarm will still sound in the event  
of a power failure.  
Charging your iPod  
Note: Please make sure you are using the correct insert for your iPod (see Install iPod Insert) and that it is properly docked  
into the iH120. Failure to do so may damage your iPod.  
1. While your iPod is docked in the unit and the unit is connected to AC power, it recharges (until fully charged). Note that  
non-docking iPods will NOT charge.  
6
Listening to iPod  
1. Dock the already playing iPod. The iH120 will automatically turn on and you will hear the music playing from your iPod.  
Note: If the playing song/music loudness is too low on the iPod itself, iH120 may not detect iPod is in play mode. Press  
the Play/Pause Button on main unit or remote control twice to play it.  
2. When the iPod is docked and in standby mode, press the  
The iPod Icon will appear on the display, showing iPod playing mode.  
3. Press the Button again to pause play; press again to resume it.  
and Button on the iH120 or on the remote control to adjust the system volume.  
Button on the iH120 or on the remote control to go to the next or previous track. Press and hold while  
Button on the iH120 or on the remote control to play it.  
4. Press the  
5. Press  
or  
track is playing for high speed forward or reverse music search of the current track.  
6. To turn off the unit, press the Alarm Reset/Power On/Off Button on the iH120 or on the remote control to turn it off.  
Your iPod will continue charging while in the dock.  
Listening to non-docking iPod or other portable audio devices  
If you are using an iPod without a docking port or other MP3 player or portable audio device, you can play it through the iH120  
via the Line-in Jack.  
1. Plug one end of an audio patch cord (available at www.ihomeaudio.com) into the headphone or line-out jack on  
your device and the other end of the patch cord into the iH120 Line-in Jack, located on the back of the unit.  
2. Press the  
Button on the iH120 or on the remote until the iPod Icon appears on the top part of the display, indicating  
Line-in playing mode.  
Note: If iPod and line-in device are both playing at the same time, both sound sources will play.  
3. Turn on and play your device.  
4. Press the  
and Button on the iH120 or on the remote control to adjust the system volume. You may need to adjust  
your device volume, too.  
5. To turn off the unit, press the  
device, too.  
Button on main unit or remote control to turn it off. Please remember to turn off your  
Dimmer Operation  
During normal operation, press the Snooze/Dimmer Button to control the brightness of the LCD display.  
7
Sleep Operation  
Sleep mode lets you sleep to your iPod, gradually lowering the volume until the unit shuts off at the selected time.  
1. Press the Sleep Button to enter sleep mode. The Sleep Icon will appear on the display to indicate the unit is in sleep  
mode. The unit will automatically turn off after the selected time. Sleep mode has a Gentle Sleep feature which gradually  
lowers the volume 15 seconds before auto power off.  
2. You can adjust the sleep timer from 120, 90, 60, 30 or 15 minutes by pressing the Sleep Button again.  
3. When the display changes back to show the real time, press the Sleep Button once to show the sleep time remaining.  
Pressing it again will change the sleep time to the next lowest increment.  
4. The iH120 has independent volume setting for sleep mode so you can adjust the sleeping volume without affecting the  
alarm volume. Press the  
and  
Button on main unit or remote control to adjust the sleep volume. The sleep volume  
will remain at that level the next time you enter sleep mode until controls are changed.  
5. To stop listening at any time, press the Alarm Reset/Power On/Off Button on the iH120 or on the remote control to  
turn it off.  
Click Sound Operation  
During normal operation, press and hold the Wake-to Button to set button click sound on or off. After the display shows  
“CLC”, press  
or  
Button to set click sound on or off, then wait around 5 seconds to exit the setting mode.  
8
A Consumer Guide to Product Safety  
When used in the directed manner, this unit has been designed and manufactured to ensure your personal safety. However,  
improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully  
before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in  
these instructions and on the unit.  
1. Water and Moisture – The unit should not be used near water. For example: near a bathtub, washbowl, kitchen sink,  
laundry tub, swimming pool or in a wet basement.  
2. Ventilation – The unit should be situated so that its location or position does not interfere with its proper ventilation. For  
example, it should not be situated on a bed, sofa, rug or similar surface that may block ventilation openings. Also, it  
should not be placed in a built-in installation, such as a bookcase or cabinet, which may impede the flow of air through  
the ventilation openings.  
3. Heat – The unit should be situated away from heat sources such as radiators, heat registers, stoves or other appliances  
(including amplifiers) that produce heat.  
4. Power Sources – The unit should be connected to a power supply only of the type described in the operating instructions  
or as marked on the appliance.  
5. Power-Cable Protection – Power supply cables should be routed so that they are not likely to be walked on or pinched  
by items placed upon or against them. It is always best to have a clear area from where the cable exits the unit to where  
it is plugged into an AC socket.  
6. Cleaning – The unit should be cleaned only as recommended. See the Maintenance section of this manual for cleaning  
instructions.  
7. Objects and Liquid Entry – Care should be taken so that objects do not fall and liquids are not spilled into any openings  
or vents located on the product.  
8. Attachments – Do not use attachments not recommended by the product manufacturer.  
9. Lightning and Power Surge Protection – Unplug the unit from the wall socket and disconnect the antenna or cable  
system during a lightning storm or when it is left unattended and unused for long periods of time. This will prevent damage  
to the product due to lightning and power-line surges.  
10. Overloading – Do not overload wall sockets, extension cords, or integral convenience receptacles as this can result in  
a risk of fire or electric shock.  
11. Damage Requiring Service – The unit should be serviced by qualified service personnel when:  
A. the power supply cable or plug has been damaged.  
B. objects have fallen into or liquid has been spilled into the enclosure.  
C. the unit has been exposed to rain.  
D. the unit has been dropped or the enclosure damaged.  
E. the unit exhibits a marked change in performance or does not operate normally.  
12. Antenna – Do not connect an external antenna to the unit (other than that provided).  
13. Periods of Nonuse – If the unit is to be left unused for an extended period of time, such as a month or longer, the power  
cable should be unplugged from the unit to prevent damage or corrosion.  
14. Servicing – The user should not attempt to service the unit beyond those methods described in the users operating  
instructions. Service methods not covered in the operating instructions should be referred to qualified service personnel.  
9
Trouble Shooting  
Symptom  
Possible Problem  
Solution  
Unit doesn’t respond AC adaptor isn’t plugged to a wall outlet or  
Plug the AC adaptor into a wall outlet and plug the connector into  
the power supply jack on the unit  
(no power)  
the connector is not plugged into the power  
supply jack on the back of the unit  
Wall outlet is not functioning  
Using no or wrong iPod insert  
iPod is not docked properly  
Plug another device into the same outlet to confirm the outlet is working  
Make sure the dock insert is the proper fit for your iPod  
iPod cannot dock  
properly  
Remove your iPod from the connector and check for any  
obstruction on the connectors in the dock and on your iPod.  
Then reseat it in the dock.  
iPod does not  
respond to the unit  
Remove your iPod from the connector and check for any  
obstruction on the connectors in the dock and on your iPod.  
Then reseat it in the dock.  
iPod is not docked properly  
Upgrade software on your iPod via iTunes  
Your iPod software is too old  
iPod is locked up  
Please make sure your iPod is working properly before docking  
it to the unit. Please refer to your iPod manual for details on  
iPod operation.  
st  
nd  
Using 1 or 2 generation iPod or other device iH120 cannot control those iPods or other devices.  
iPod didn’t charge  
up  
iPod is not docked properly  
Remove your iPod from the connector and check for any  
obstruction on the connectors in the dock and on your iPod.  
Then reseat it in the dock.  
iPod is locked up/frozen  
iPod battery has problem  
Volume level is set too high  
Sound source is distorted  
Please make sure your iPod is working properly before docking  
it to the unit. Please refer to your iPod manual for details.  
Sound is distorted  
Decrease the volume.  
If iPod original sound source is poor quality, distortion and noise  
are easily noticed with high-power speakers.  
Try a different audio source such as a music CD.  
If you are using an iPod Shuffle or external sound source like  
older generation iPod, try reducing the output volume on the  
device itself. Also, try turning bass boost OFF.  
Remote Control  
didn’t work  
Battery weak  
Replace with new battery  
Remote Control is not pointed toward the  
IR sensor  
Point the Remote Control toward the IR sensor, within 10 feet of  
the unit.  
10  
Solución De Problemas  
Síntoma  
Posible Problema  
Solución  
La unidad no  
funciona (no circula  
corriente eléctrica)  
El adaptador de AC no está conectado al  
Conecte el adaptador de AC al tomacorriente y también  
tomacorriente o el conector no está conectado conecte el conector a la ficha en la parte posterior de la unidad  
a la ficha en la parte posterior de la unidad  
El tomacorriente no funciona  
Coloque otro aparato en ese mismo tomacorriente para  
confirmar si el que no funciona es el tomacorriente  
El iPod no encastra  
correctamente  
No ha colocado el encastre del iPod, o está  
utilizando el encastre incorrecto.  
Verifique que el encastre sea el apropiado para su iPod  
El iPod no encastra correctamente  
El iPod no está instalado correctamente  
Su software es obsoleto  
Quite el iPod del encastre y retire la posible obstrucción del  
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.  
El iPod no se  
comunica con la  
unidad  
Quite el iPod del encastre y verifique posibles obstrucciones del  
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.  
Renueve su software. Para mayor información, diríjase a  
El iPod no responde  
Verifique que su iPod funcione correctamente antes de conectarlo  
a la unidad. Refiérase al manual de su iPod para más detalles.  
Usted tiene un iPod de primera o segunda  
generación, un Shuffle u otro tipo de aparato  
El iH120 no puede controlar estos otros aparatos  
El iPod no carga  
El iPod no está instalado correctamente  
Quite el iPod del encastre y retire la posible obstrucción del  
encastre o de su iPod. Vuelva a colocar el iPod dentro del encastre.  
El iPod está trabado/no responde  
Por favor asegúrese de que su iPod funcione correctamente  
antes de colocarlo en el encastre. Refiérase al manual de su  
iPod para mayor información.  
La batería del iPod podría tener algún  
inconveniente  
El sonido sale  
distorsionado  
El volumen se encuentra muy alto  
Baje el volumen y no EQ  
El sonido sale distorsionado de la unidad  
Si el sonido original de su iPod era de pobre calidad, las  
distorsiones y ruidos se harán más notables con los  
parlantes de alta potencia. Pruebe utilizar otra fuente de  
audio como un CD.  
Si está utilizando un iPod de primeras generaciones o un  
Shuffle, intente bajar el volumen de su aparato. También intente  
apagar el amplificador de bajos  
El control remoto no  
funciona  
Las baterías están gastadas  
Reemplace las baterías por nuevas  
No está apuntando el control remoto hacia  
el iH120  
Apunte el control remoto hacia el iH120 y manténgase a una  
distancia máxima de 10 pies de la unidad.  
11  
Limited 90-Day Warranty Information  
iHome Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies), warrants this product to be free from defects  
in workmanship and materials, under normal use and conditions, for a period of 90 days from the date of original purchase.  
Should this product fail to function in a satisfactory manner, it is best to first return it to the store where it was originally purchased. Should  
this fail to resolve the matter and service still be required by reason of any defect or malfunction during the warranty period, SDI Technologies  
will repair or, at its discretion, replace this product without charge (except for a $10.00 charge for handling, packing, return UPS/postage,  
and insurance). This decision is subject to verification of the defect or malfunction upon delivery of this product to the Factory Service Center  
l
isted below. The product must include proof of purchase, including date of purchase. The fee for service without proof of purchase is $25.00.  
Before returning this product for service, please first replace the batteries (if applicable) with fresh ones, as exhausted or defective batteries  
are the most common cause of problems encountered.  
If service is still required:  
1. Remove the batteries (if applicable) and pack the unit in a well padded, heavy corrugated box.  
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date of purchase, if within the warranty period.  
3. Enclose a check or money order payable to the order of SDI Technologies, for the sum of $10.00 ($25.00 without proof of purchase).  
4. Send the unit prepaid and insured, to the Factory Service Center listed below.  
Consumer Repair Department  
SDI Technologies Inc.  
1330 Goodyear Drive  
El Paso, TX 79936-6420  
Disclaimer of Warranty  
NOTE: This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover (i) products which  
have been damaged by negligence or willful actions, misuse or accident, or which have been modified or repaired by unauthorized  
persons; (ii) cracked or broken cabinets, or units damaged by excessive heat; (iii) damage to digital media players, CD’s or tape cassettes  
(if applicable); (iv) the cost of shipping this product to the Factory Service Center and its return to the owner.  
This warranty is valid only in the United States of America and does not extend to owners of the product other than to the original  
purchaser. In no event will SDI Technologies or any of its affiliates, contractors, resellers, their officers, directors, shareholders, members  
or agents be liable to you or any third party for any consequential or incidental damages, any lost profits, actual, exemplary or punitive  
damages. (Some states do not allow limitations on implied warranties or exclusion of consequential damages, so these restrictions may  
not apply to you.) This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.  
Your acknowledgement and agreement to fully and completely abide by the above mentioned disclaimer of warranty is contractually  
binding to you upon your transfer of currency (money order, cashier's check, or credit card) for purchase of your SDI Technologies  
product.  
© 2009 SDI Technologies, Inc. All rights reserved  
or call 1-800-288-2792 Toll Free  
iH120-0210009-1  
Printed in China  
12  

Motorola WT4070 User Manual
LG Electronics AX4270 User Manual
Kenwood KDC MP4029G User Manual
Hitachi CP L540E User Manual
Emerson CKD3630 User Manual
Echo Bear Cat SC3206 User Manual
Clarion DXZ375MP User Manual
Apple iPhone 3G A1303 User Manual
American Audio DIGI PRO User Manual
Addonics Technologies DCHDIEU User Manual