Nokia 6080 User Guide
9253006
Issue 1
Nokia operates a policy of continuous development. Nokia reserves the right to make
changes and improvements to any of the products described in this document without prior
notice.
This Nokia device complies with Directive 2002/95/EC on the restriction of the use of certain
hazardous substances in electrical and electronic equipment.
Under no circumstances shall Nokia be responsible for any loss of data or income or any
special, incidental, consequential or indirect damages howsoever caused.
The contents of this document are provided "as is". Except as required by applicable law, no
warranties of any kind, either express or implied, including, but not limited to, the implied
warranties of merchantability and fitness for a particular purpose, are made in relation to the
accuracy, reliability or contents of this document. Nokia reserves the right to revise this
document or withdraw it at any time without prior notice.
The availability of particular products may vary by region. Please check with the Nokia dealer
nearest to you.
This device may contain commodities, technology or software subject to export laws and
regulations from the US and other countries. Diversion contrary to law is prohibited.
9253006/Issue 1
Contents
Info messages ...................................... 39
For your safety.......................... 6
General information................. 9
Overview of functions........................... 9
Access codes............................................ 9
Configuration settings service ........ 10
Download content and applications 11
Nokia support and
contact information........................... 11
1. Get started......................... 12
Install the SIM card and battery .... 12
Charge the battery.............................. 13
Switch the phone on and off........... 14
Antenna ................................................. 14
Wrist strap ............................................ 15
Search for a contact .......................... 43
My presence ......................................... 45
Subscribed names............................... 46
Settings.................................................. 47
Groups.................................................... 47
Voice dialing......................................... 48
Speed dials............................................ 49
Info, service, and my numbers ........ 49
2. Your phone......................... 16
Keys and parts...................................... 16
Standby mode...................................... 17
Keypad lock (keyguard) ..................... 19
3. Call functions..................... 20
Make a call ........................................... 20
Answer or reject a call....................... 20
Options during a call.......................... 21
4. Write text........................... 22
Settings.................................................. 22
Predictive text input .......................... 22
Traditional text input......................... 23
8. Log ...................................... 50
Recent calls lists.................................. 50
Counters and timers........................... 50
9. Settings ............................. 51
Profiles ................................................... 51
Themes................................................... 51
Tones....................................................... 51
Lights...................................................... 52
My shortcuts ........................................ 52
Display.................................................... 52
Time and date ...................................... 53
5. Navigate the menus .......... 24
6. Messages............................ 25
Text messages (SMS).......................... 25
Multimedia messages (MMS).......... 27
Memory full.......................................... 29
Folders.................................................... 30
Postcards............................................... 30
4
Call........................................................... 54 Add a one-to-one contact................ 78
Phone...................................................... 54 Create and set up channels.............. 78
Connectivity.......................................... 55 PTT settings........................................... 80
Enhancements...................................... 57
Configuration........................................ 58
Security .................................................. 59
Restore factory settings..................... 59
Cookies ................................................... 84
Browser security .................................. 86
Positioning information..................... 88
10. Operator menu ................ 60
11. Gallery.............................. 61
12. Media............................... 62
Camera ................................................... 62
Radio....................................................... 62
Recorder................................................. 64
13. Organizer.......................... 65
Alarm clock............................................ 65
Calendar................................................. 65
To-do list................................................ 66
Notes....................................................... 67
Synchronization................................... 67
Calculator .............................................. 68
Stopwatch ............................................. 69
Countdown timer ................................ 70
17. SIM services ..................... 90
18. PC connectivity................ 91
Nokia PC Suite...................................... 91
Packet data, HSCSD, and CSD.......... 91
Data communication applications . 91
19. Battery information......... 92
Charging and discharging................. 92
Nokia battery authentication
14. Applications..................... 71
Games..................................................... 71
Collection............................................... 71
guidelines............................................... 92
Care and maintenance ........... 95
Additional safety information 96
Index..................................... 100
15. Push to talk ..................... 73
Push to talk menu............................... 73
Connect to and disconnect PTT....... 74
Make and receive a PTT call............. 74
Callback requests................................. 76
5
F o r y o u r s a f e t y
For your safety
Read these simple guidelines. Not following them may be dangerous or illegal.
Read the complete user guide for further information.
SWITCH ON SAFELY
Do not switch the phone on when wireless phone use is prohibited or
when it may cause interference or danger.
ROAD SAFETY COMES FIRST
Obey all local laws. Always keep your hands free to operate the
vehicle while driving. Your first consideration while driving should be
road safety.
INTERFERENCE
All wireless phones may be susceptible to interference, which could
affect performance.
SWITCH OFF IN HOSPITALS
Follow any restrictions. Switch the phone off near medical
equipment.
SWITCH OFF IN AIRCRAFT
Follow any restrictions. Wireless devices can cause interference in
aircraft.
SWITCH OFF WHEN REFUELING
Do not use the phone at a refueling point. Do not use near fuel or
chemicals.
SWITCH OFF NEAR BLASTING
Follow any restrictions. Do not use the phone where blasting is in
progress.
USE SENSIBLY
Use only in the normal position as explained in the product
documentation. Do not touch the antenna unnecessarily.
QUALIFIED SERVICE
Only qualified personnel may install or repair this product.
ENHANCEMENTS AND BATTERIES
Use only approved enhancements and batteries. Do not connect
incompatible products.
6
F o r y o u r s a f e t y
WATER-RESISTANCE
Your phone is not water-resistant. Keep it dry.
BACK-UP COPIES
Remember to make back-up copies or keep a written record of all
important information stored in your phone.
CONNECTING TO OTHER DEVICES
When connecting to any other device, read its user guide for detailed
safety instructions. Do not connect incompatible products.
EMERGENCY CALLS
Ensure the phone is switched on and in service. Press the end key as
many times as needed to clear the display and return to the start
screen. Enter the emergency number, then press the call key. Give
your location. Do not end the call until given permission to do so.
■ About your device
The wireless device described in this guide is approved for use on the EGSM 900
and GSM 1800 and 1900 networks. Contact your service provider for more
information about networks.
When using the features in this device, obey all laws and respect the privacy and
legitimate rights of others, including copyrights.
Warning: To use any features in this device, other than the alarm clock,
the device must be switched on. Do not switch the device on when
wireless device use may cause interference or danger.
■ Network services
To use the phone you must have service from a wireless service provider. Many of
the features in this device depend on features in the wireless network to
function. These network services may not be available on all networks or you may
have to make specific arrangements with your service provider before you can
utilize network services. Your service provider may need to give you additional
instructions for their use and explain what charges will apply. Some networks
may have limitations that affect how you can use network services. For instance,
some networks may not support all language-dependent characters and services.
Your service provider may have requested that certain features be disabled or not
activated in your device. If so, they will not appear on your device menu. Your
device may also have been specially configured for your network provider. This
7
F o r y o u r s a f e t y
configuration may include changes in menu names, menu order, and icons.
Contact your service provider for more information.
This device supports WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP
protocols. Some features of this device, such as text messages, multimedia
messages, audio messages, instant messaging service, e-mail, presence enhanced
contacts, mobile Internet services, content and application download, and
synchronization with a remote Internet server, require network support for these
technologies.
■ Shared memory
The phone has two memories. The following features may share the first memory:
contacts, text messages, multimedia messages (but no attachments), audio
messages, instant messaging, groups, voice commands, calendar, and to-do
notes. The second shared memory is used by files stored in Gallery, attachments
of multimedia messages, e-mail, and JavaTM applications. Use of one or more of
these features may reduce the memory available for the remaining features
sharing memory. For example, saving many Java applications may use all of the
available memory. Your device may display a message that the memory is full
when you try to use a shared memory feature. In this case, delete some of the
information or entries stored in the shared memory features before continuing.
Some of the features, such as text messages, may have a certain amount of
memory specially allotted to them in addition to the memory shared with other
features.
■ Enhancements
A few practical rules about accessories and enhancements:
•
•
Keep all accessories and enhancements out of the reach of small children.
When you disconnect the power cord of any accessory or enhancement, grasp
and pull the plug, not the cord.
•
•
Check regularly that enhancements installed in a vehicle are mounted and
are operating properly.
Installation of any complex car enhancements must be made by qualified
personnel only.
8
G e n e r a l i n f o r m a t i o n
General information
■ Overview of functions
Your phone provides many functions that are practical for daily use,
such as a calendar, a clock, an alarm clock, a radio, and a built-in
camera. Your phone also supports the following functions:
• Enhanced data rates for GSM evolution (EDGE). See “Packet data
(EGPRS),” p. 56.
• Extensible hypertext markup language (XHTML). See “Web,” p. 81.
• Audio messaging. See “Nokia Xpress audio messaging,” p. 31.
• Instant messaging. See “Instant messaging (IM),” p. 32.
• E-mail application. See “E-mail application,” p. 37.
• Push to talk. See “Push to talk,” p. 73.
• Presence-enhanced contacts. See “My presence,” p. 45.
• Java 2 Platform, Micro Edition (J2METM). See “Applications,” p. 71.
• Synchronization and file transfer with PC Suite. See “Nokia PC Suite,”
p. 91.
■ Access codes
Security code
The security code (5 to 10 digits) helps to protect your phone against
unauthorized use. The preset code is 12345. To change the code, and to
set the phone to request the code, see “Security,” p. 59.
PIN codes
The personal identification number (PIN) code and the universal
personal identification number (UPIN) code (4 to 8 digits) help to
protect your SIM card against unauthorized use. See “Security,” p. 59.
The PIN2 code (4 to 8 digits) may be supplied with the SIM card and is
required for some functions.
9
G e n e r a l i n f o r m a t i o n
The module PIN is required to access the information in the security
module. See “Security module,” p. 86.
The signing PIN is required for the digital signature. See “Digital
signature,” p. 88.
PUK codes
The personal unblocking key (PUK) code and the universal personal
unblocking key (UPUK) code (8 digits) are required to change a blocked
PIN code and UPIN code, respectively. The PUK2 code (8 digits) is
required to change a blocked PIN2 code. If the codes are not supplied
with the SIM card, contact your local service provider for the codes.
Barring password
The barring password (4 digits) is required when using the Call barring
service. See “Security,” p. 59.
■ Configuration settings service
To use some of the network services, such as mobile Internet services,
MMS, Nokia Xpress audio messaging, or remote Internet server
synchronization, your phone needs the correct configuration settings.
You may be able to receive the settings directly as a configuration
message. After receiving the settings, you need to save them on your
phone. The service provider may provide a PIN that is needed to save the
settings. For more information on availability, contact your network
operator, service provider, nearest authorized Nokia dealer, or visit the
support area on the Nokia Web site at www.nokia.com/support.
When you have received a configuration message Configuration sett.
received is displayed.
To save the settings, select Show > Save. If the phone requests Enter
settings' PIN:, enter the PIN code for the settings, and select OK. To
receive the PIN code, contact the service provider that supplies the
settings. If no settings are saved yet, these settings are saved and set as
default configuration settings. Otherwise, the phone asks Activate saved
configuration settings?.
10
G e n e r a l i n f o r m a t i o n
To discard the received settings, select Exit or Show > Discard.
To edit the settings, see “Configuration,” p. 58.
■ Download content and applications
You may be able to download new content (for example, themes) to the
phone (network service). Select the download function (for example, in
the Gallery menu). To access the download function, see the respective
menu descriptions. For the availability of different services, pricing, and
tariffs, contact your service provider.
Important: Use only services that you trust and that offer adequate
security and protection against harmful software.
■ Nokia support and contact information
Check www.nokia.com/support or your local Nokia Web site for the
latest version of this guide, additional information, downloads, and
services related to your Nokia product.
On the Web site, you can get information on the use of Nokia products
and services. If you need to contact customer service, check the list of
local Nokia contact centers at www.nokia.com/customerservice.
For maintenance services, check your nearest Nokia service center at
www.nokia.com/repair.
11
G e t s t a r t e d
1. Get started
■ Install the SIM card and battery
Always switch the device off and disconnect the charger before removing the
battery.
Keep all SIM cards out of the reach of small children.
For availability and information on using SIM card services, contact your SIM
card vendor. This may be the service provider, network operator, or other vendor.
This device is intended for use with the BL-5B battery.
The SIM card and its contacts can easily be damaged by scratches or
bending, so be careful when handling, inserting, or removing the card.
To remove the back cover of the phone,
press the release button (1), and lift the
back cover (2).
Ensure that the gold-colored contact area
on the SIM card is facing downwards, and
insert the SIM card into the SIM card
holder until it snaps into position (3).
Insert the battery (4). Observe the battery
contacts. Always use original Nokia
batteries. See “Nokia battery
authentication guidelines,” p. 92.
Align the top of the back cover with the
top of the phone (5), and press the bottom
of the back cover to lock it (6).
12
G e t s t a r t e d
To remove the battery, lift the lower end of
the battery out of the compartment (7).
To remove the SIM card, press the SIM
card release (8), and slide the SIM card
towards the top of the phone (9).
■ Charge the battery
Warning: Use only batteries, chargers, and enhancements approved by
Nokia for use with this particular model. The use of any other types may
invalidate any approval or warranty, and may be dangerous.
Check the model number of any charger before use with this device. This device is
intended for use when supplied with power from an AC-3, AC-4, and DC-4
charger, and from an LCH-9 charger when used with the CA-44 charger adapter.
For availability of approved enhancements, please check with your dealer.
When you disconnect the power cord of any enhancement, grasp and pull the
plug, not the cord.
1. Connect the charger to a wall socket.
2. Connect the lead from the charger to the
socket on the bottom of your phone.
If the battery is completely discharged, it
may take a few minutes before the charging
indicator appears on the display or before any calls can be made.
The charging time depends on the charger and the battery used. For
example, charging a BL-5B battery with the AC-3 charger takes about
1 hour and 10 minutes while the phone is in the standby mode.
13
G e t s t a r t e d
■ Switch the phone on and off
Warning: Do not switch the phone on when wireless
phone use is prohibited or when it may cause
interference or danger.
To switch the phone on, press and hold the power key.
If the phone asks for a PIN or a UPIN code, enter the code
(displayed as ****), and select OK.
To switch the phone off, press and hold the power key.
Set the time, time zone, and date
Enter the local time, select the time zone of your location in terms of the
time difference with respect to Greenwich Mean Time (GMT), and enter
the date. See “Time and date,” p. 53.
Plug and play service
When you switch on your phone for the first time, and the phone is in
the standby mode, you are asked to get the configuration settings from
your service provider (network service). Confirm or decline the query.
See "Connect to service provider support ," p. 58 and “Configuration
settings service,” p. 10.
■ Antenna
Your device has an internal antenna.
Note: As with any other radio
transmitting device, do not touch the
antenna unnecessarily when the device
is switched on. Contact with the antenna
affects call quality and may cause the
device to operate at a higher power level
than otherwise needed. Avoiding contact
with the antenna area when operating
the device optimizes the antenna
performance and the battery life.
14
Y o u r p h o n e
2. Your phone
■ Keys and parts
• Power key (1)
• Earpiece (2)
• Loudspeaker (3)
• Display (4)
• Volume up and
push to talk (PTT) key (5)
• Volume down and
voice command key (6)
• Infrared (IR) port (7)
• Middle selection key (8)
• 4-way navigation key (9)
• Left selection key (10)
• Right selection key (11)
• Call key (12)
• End key (13)
• Keypad, may vary by region (14)
• Charger connector (15)
• Microphone (16)
• Pop-PortTM connector (17)
• Camera lens (18)
16
Y o u r p h o n e
■ Standby mode
When the phone is ready for use, and you have not entered any
characters, the phone is in the standby mode.
1 Name of the network or operator logo
2 Signal strength of the cellular network
3 Battery charge level
4 Left selection key (Go to)
5 Middle selection key (Menu)
6 Right selection key (Names)
The right selection key may be another
shortcut to a function that you selected. See
“My shortcuts,” p. 52. Operator variants may have an operator-specific
name to access an operator-specific Web site.
Personal shortcut list
The left selection key is Go to. To view the functions in the personal
shortcut list, select Go to. To activate a function, select it.
To view a list with available functions, select Go to > Options > Select
options. To add a function to the shortcut list, select Mark. To remove a
function from the list, select Unmark.
To rearrange the functions on your personal shortcut list, select Go to >
Options > Organise. Select the desired function, Move, and the place
where you want to move the function.
Shortcuts in standby mode
• To access the list of dialed numbers, press the call key once. Scroll to
a number or name; to call the number, press the call key.
• To open the Web browser, press and hold 0.
• To call your voice mailbox, press and hold 1.
• Use the navigation key as a shortcut. See “My shortcuts,” p. 52.
17
Y o u r p h o n e
Power saving
A digital clock view overwrites the display when no
function of the phone has been used for a certain
period of time. To activate the power saver, see
Power saver in “Display,” p. 52. To deactivate the
screen saver, press any key.
Indicators
You have unread messages.
The phone registered a missed call. See “Log,” p. 50.
The keypad is locked. See “Keypad lock (keyguard),” p. 19.
The phone does not ring for an incoming call or text message
See “Tones,” p. 51.
The alarm clock is set to On. See “Alarm clock,” p. 65.
If the packet data connection mode Always online is selected,
the packet data service is available. See “Packet data (EGPRS),”
p. 56.
A packet data connection is established. See “Packet data
(EGPRS),” p. 56 and “Browse pages,” p. 82.
The packet data connection is suspended (on hold), for example,
if there is an incoming or outgoing call during a packet data
dial-up connection.
When the infrared connection is activated, the indicator is
shown continuously.
Push to talk connection is active or suspended. See “Push to
talk,” p. 73.
18
Y o u r p h o n e
■ Keypad lock (keyguard)
To prevent the keys from being accidentally pressed, select Menu, and
press * within 3.5 seconds to lock the keypad.
To unlock the keypad, select Unlock, and press * within 1.5 seconds. If
the Security keyguard is set On, enter the security code if requested.
To answer a call when the keyguard is on, press the call key. When you
end or reject the call, the keypad automatically locks.
For Automatic keyguard and Security keyguard, see “Phone,” p. 54.
When the keyguard is on, calls still may be possible to the official emergency
number programmed into your device.
19
C a l l f u n c t i o n s
3. Call functions
■ Make a call
1. Enter the phone number, including the area code.
+ character replaces the international access code), then enter the
country code, the area code without the leading 0, if necessary, and
the phone number.
2. To call the number, press the call key.
3. To end the call or to cancel the call attempt, press the end key.
To make a call using names, search for a name or phone number in
Contacts. See “Search for a contact,” p. 43.
Press the call key to call the number.
To access the list of up to 20 dialed numbers, press the call key once in
the standby mode. To call the number, select a number or name, and
press the call key.
Speed dialing
Assign a phone number to one of the speed-dialing keys, 2 to 9. See
“Speed dials,” p. 49. Call the number in either of the following ways:
• Press a speed-dialing key, then press the call key.
• If Speed dialling is set to On, press and hold a speed-dialing key until
the call begins. See Speed dialling in “Call,” p. 54.
■ Answer or reject a call
To answer an incoming call, press the call key. To end the call, press the
end key.
To reject an incoming call, press the end key.
To mute the ringing tone, select Silence.
20
C a l l f u n c t i o n s
Tip: If the Divert if busy function is activated to divert the calls
(for example, to your voice mailbox), rejecting an incoming call
also diverts the call. See “Call,” p. 54.
If a compatible headset with a headset key is connected to the phone, to
answer and end a call, press the headset key.
Call waiting
To answer the waiting call during an active call, press the call key. The
first call is put on hold. To end the active call, press the end key.
To activate the Call waiting function, see “Call,” p. 54.
■ Options during a call
Warning: Do not hold the device near your ear when the loudspeaker
is in use, because the volume may be extremely loud.
Many of the options that you can use during a call are network services.
For availability, contact your network operator or service provider.
During a call, select Options and from the following options:
Call options are Mute or Unmute, Contacts, Menu, Auto volume on or
Auto volume off, Record, Lock keypad, Loudspeaker, or Handset.
Network services options are Answer and Reject, Hold or Unhold, New
call, Add to conference, End call, End all calls, and the following:
Send DTMF — to send tone strings
Swap — to switch between the active call and the call on hold
Transfer — to connect a call on hold to an active call and disconnect
yourself
Conference — to make a conference call that allows up to five persons to
take part in a conference call
Private call — to discuss privately in a conference call
21
W r i t e t e x t
4. Write text
You can enter text (for example, when writing messages) using
traditional or predictive text input. When using traditional text input,
press a number key, 1 to 9, repeatedly until the desired character
appears. In predictive text input you can enter a letter with a single
keypress.
When you are writing text, predictive text input is indicated by
and traditional text input by
at the top left of the display.
,
, or
appear next to the text input indicator, indicating the
character case.
To change the character case and the text input mode, press #.
indicates number mode. To change from the letter to number
mode, press and hold #, and select Number mode. To insert a special
character, press and hold *.
■ Settings
To set the writing language, select Options > Writing language.
Predictive text input is only available for the languages listed.
Select Options > Prediction on to set the predictive text input or
Prediction off to set traditional text input.
■ Predictive text input
Predictive text input is based on a built-in dictionary to which you can
add new words.
1. Start writing a word using the 2 to 9 keys. Press each key only once
for a single letter. The word changes after each keypress.
2. When you have finished writing the word and it is correct, to confirm
it, press 0 to add a space, or scroll in any direction. Press a navigation
key to move the cursor.
If the word is not correct, press * repeatedly, or select Options >
Matches. Select the correct word and Use.
22
W r i t e t e x t
If ? is displayed after the word, the word you intended to write is not
in the dictionary. To add the word to the dictionary, select Spell.
Enter the word (traditional text input is used), and select Save.
To enter a full stop, press 1.
3. Start writing the next word.
Write compound words
Enter the first part of the word, and scroll right to confirm it. Write the
last part of the word, and confirm the word.
■ Traditional text input
Press a number key, 1 to 9, repeatedly until the desired character
appears. Not all characters available under a number key are printed on
the key. The characters available depend on the writing language. See
“Settings,” p. 22.
If the next letter you want is located on the same key as the present one,
wait until the cursor appears, or press any of the navigation keys and
enter the letter.
The most common punctuation marks and special characters are
available under the 1 key.
23
N a v i g a t e t h e m e n u s
5. Navigate the menus
The phone offers you an extensive range of functions, which are
grouped into menus.
1. To access the menu, select Menu. To change the menu view, select
Options > Main menu view > List or Grid.
2. Scroll through the menu, and select a submenu (for example,
Settings).
3. If the menu contains submenus, select the one that you want (for
example, Call).
4. If the selected menu contains further submenus, select the one that
you want (for example, Anykey answer).
5. Select the setting of your choice.
6. To return to the previous menu level, select Back. To exit the menu,
select Exit.
24
M e s s a g e s
6. Messages
The message services can only be used if they are supported
by your network or your service provider.
Note: When sending messages, your phone may display Message sent.
This is an indication that the message has been sent by your device to
the message center number programmed into your device. This is not an
indication that the message has been received at the intended
destination. For more details about messaging services, check with your
service provider.
Important: Exercise caution when opening messages. Messages may
contain malicious software or otherwise be harmful to your device or
PC.
Only devices that have compatible features can receive and display
messages. The appearance of a message may vary depending on the
receiving device.
■ Text messages (SMS)
Using the short message service (SMS) you can send and receive
multipart messages made of several ordinary text messages (network
service) that can contain pictures.
Before you can send any text, picture, or e-mail message, you must save
your message center number. See “Message settings,” p. 40.
To check SMS e-mail service availability and to subscribe to the service,
contact your service provider.
Your device supports the sending of text messages beyond the character limit for
a single message. Longer messages will be sent as a series of two or more
messages. Your service provider may charge accordingly. Characters that use
accents or other marks, and characters from some language options like Chinese,
take up more space limiting the number of characters that can be sent in a single
message.
25
M e s s a g e s
Write and send an SMS message
1. Select Menu > Messaging > Create message > Text message.
2. Enter a message. See “Write text,” p. 22.
At the top of the display, the message length indicator tracks the
number of available characters. For example, 10/2 means that you
can still add 10 characters for the text to be sent as two messages.
To insert text templates or a picture into the message, see
“Templates,” p. 27. Each picture message comprises several text
messages. Sending one picture or multipart message may cost more
than sending one text message.
3. To send the message, select Send > Recently used, To phone number,
To many, or To e-mail address. To send a message using a predefined
message profile, select Via sending profile. For the message profile,
see “Text and SMS e-mail,” p. 40. Select or enter a phone number or
e-mail address, or select a profile.
Read and reply to an SMS message
is shown when you received an SMS message or an SMS e-mail. The
blinking
indicates that the message memory is full. Before you can
receive new messages, delete some of your old messages in the Inbox
folder.
1. To view a new message, select Show. To view it later, select Exit.
To read the message later, select Menu > Messaging > Inbox. If more
than one message is received, select the message that you want to
read.
indicates an unread message.
2. While reading a message, select Options and delete or forward the
message; edit the message as a text message or an SMS e-mail;
rename the message you are reading or move it to another folder; or
view or extract message details. You can also copy text from the
beginning of the message to your phone calendar as a reminder note.
To save the picture in the Templates folder when reading a picture
message, select Save picture.
3. To reply as a message, select Reply > Text message, Multimedia msg.,
Flash message, or Audio message. Enter the reply message. When
26
M e s s a g e s
replying to an e-mail, first confirm or edit the e-mail address and
subject.
4. To send the message to the displayed number, select Send > OK.
Templates
Your phone has text templates
and picture templates
that you
can use in text, picture, or SMS e-mail messages.
To access the template list, select Menu > Messaging > Saved items >
Text messages > Templates.
■ Multimedia messages (MMS)
A multimedia message can contain text, sound, a picture, a calendar
note, a business card, or a video clip. If the message is too large, the
phone may not be able to receive it. Some networks allow text messages
that include an Internet address where you can view the multimedia
message.
You cannot receive multimedia messages during a call, a game, another
Java application, or an active browsing session over GSM data. Because
delivery of multimedia messages can fail for various reasons, do not rely
solely upon them for essential communications.
Write and send an MMS message
To set the settings for multimedia messaging, see “Multimedia,” p. 40.
To check availability and to subscribe to the multimedia messaging
service, contact your service provider.
Copyright protections may prevent some images, music (including ringing tones),
and other content from being copied, modified, transferred or forwarded.
1. Select Menu > Messaging > Create message > Multimedia msg..
2. Enter a message. See “Write text,” p. 22.
To insert a file, select Options > Insert and from the following
options:
Image, Sound clip, or Video clip — to insert a file from Gallery
New image — to take a new image to be added to the message
27
M e s s a g e s
New sound clip — to make a new recording to be added to the
message
Business card or Calendar note — to insert a business card or a
calendar note in the message
Slide — to insert a slide to the message. Your phone supports
multimedia messages that contain several pages (slides). Each slide
can contain text, one image, a calendar note, a business card, and
one sound clip. To open a desired slide if the message contains
several slides, select Options > Previous slide, Next slide, or Slide list.
To set the interval between the slides, select Options > Slide timing.
To move the text component to the top or bottom of the message,
select Options > Place text first or Place text last.
image, slide, or sound clip from the message, Clear text, Preview, or
Save message. In More options the following options may be
available: Insert contact, Insert number, Message details, and Edit
subject.
3. To send the message, select Send > Recently used, To phone number,
To e-mail address, or To many.
4. Select the contact from the list, or enter the recipient’s phone
number or e-mail address, or search for it in Contacts. Select OK. The
message is moved to the Outbox folder for sending.
While the multimedia message is being sent, the animated indicator
is displayed and you can use other functions on the phone. If the
sending fails, the phone tries to resend it a few times. If this fails, the
message remains in the Outbox folder, and you can try to resend it
later.
If you select Save sent messages > Yes, the sent message is saved in
the Sent items folder. See “Multimedia,” p. 40. When the message is
sent, it is not an indication that the message has been received at the
intended destination.
28
M e s s a g e s
Read and reply to an MMS message
Important: Exercise caution when opening messages. Multimedia
message objects may contain malicious software or otherwise be
harmful to your device or PC.
When your phone receives a multimedia message, the animated
is
displayed. When the message has been received,
and the text
Multimedia message received are shown.
1. To read the message, select Show. To view it later, select Exit.
To read the message later, select Menu > Messaging > Inbox. In the
list of messages, indicates an unread message. Select the
message that you want to view.
2. The function of the middle selection key changes according to the
currently displayed attachment in the message.
To view the whole message if the received message contains a
presentation, a sound clip, or a video clip, select Play.
Select Options to access Attachments (for example, a business card)
and Objects (for example, images).
3. To reply to the message, select Options > Reply > Text message,
Multimedia msg., Flash message, or Audio message. Enter the reply
message, and select Send.
Select Options to access available options.
■ Memory full
When you have received a new text message and the message memory
is full,
blinks and Text msgs. memory full. Delete msgs. is shown.
Select No, and delete some messages from a folder. To discard the
waiting message, select Exit > Yes.
When you have a new multimedia message waiting and the memory for
the messages is full,
blinks and Multimedia memory full. View
waiting msg. is shown. To view the waiting message, select Show.
Before you can save the waiting message, delete old messages to free
memory space. To save the message, select Save. To discard the waiting
message, select Exit > Yes. If you select No, you can view the message.
29
M e s s a g e s
■ Folders
The phone saves received text and multimedia messages in the Inbox
folder.
Multimedia messages that have not yet been sent are moved to the
Outbox folder.
If you have selected Message settings > Text messages > Save sent
messages > Yes, and Message settings > Multimedia msgs. > Save sent
messages > Yes, the sent messages are saved in the Sent items folder.
To save the text message that you are writing and wish to send later in
the Saved items folder, select Options > Save message > Saved text
msgs.. For multimedia messages, select the option Save message.
indicates unsent messages.
To organize your text messages, you can move some of them to My
folders or add new folders for your messages. Select Messaging > Saved
items > Text messages > My folders.
To add a folder, select Options > Add folder. If you have not saved any
folders, select Add.
To delete or rename a folder, scroll to the desired folder, and select
Options > Delete folder or Rename folder.
■ Postcards
With the postcard messaging service you can create and send postcards
that may contain an image and a greeting text. The postcard is sent to
the service provider using multimedia messaging. The service provider
prints the post card, and sends it to the postal address given with the
message. The Multimedia messaging service must be activated before
this service can be used. This feature may not be available, depending on
your phone.
Before you can use the postcard service, you must subscribe to the service. To
check the availability and costs, and to subscribe to the service, contact your
network operator or service provider.
30
M e s s a g e s
Send a postcard
Select Menu > Messaging > Create message > Postcard. Scroll to the
editor fields, and select Write to enter the name and the postal address
of the recipient; then write your greeting text. Select Insert > Open
Gallery to insert an image from Gallery or New image to insert a recent
photo. Select Optionsto see the available options. To send the postcard,
select the graphical key, or select Options > Send.
■ Flash messages
Flash messages are text messages that are instantly displayed upon
reception.
Write a flash message
Select Menu > Messaging > Create message > Flash message. Write
your message. The maximum length of a flash message is 70 characters.
To insert a blinking text into the message, select Options > Insert blink
char. to set a marker. The text after the marker blinks until a second
marker is inserted.
Receive a flash message
A received flash message is not automatically saved. To read the
message, select Read. To extract phone numbers, e-mail addresses, and
Web site addresses from the current message, select Options > Use
detail. To save the message, select Save and the folder in which you
want to save the message.
■ Nokia Xpress audio messaging
With this menu, use the multimedia message service to create and send
a voice message in a convenient way. Multimedia messaging service
must be activated before this service can be used.
31
M e s s a g e s
Create and send an audio message
1. Select Menu > Messaging > Create message > Audio message. The
recorder opens. To use the recorder, see “Recorder,” p. 64.
2. When the message is ready to send, select Options > Play to check
the message before sending, Replace sound clip to repeat the
recording, Save message (to Saved items), Save sound clip to save the
recording in Gallery, Edit subject to insert a subject to the message,
Message details to view the message details, or Loudspeaker or
Handset.
3. To send the message, select Send > Recently used, To phone number,
To e-mail address, or To many. Depending on your operator, more
options may be available.
4. Select the contact from the list, enter the recipient’s phone number
or e-mail address, or search for it in Contacts. Select OK, and the
message is moved to the Outbox folder for sending.
Receive an audio message
When your phone is receiving an audio message, 1 audio message
received is shown. Select Show to open the message, or select Show >
Play if there is more than one message received. Select Options to see
the available options. To listen to the message later, select Exit.
To save the message, select Options > Save sound clip and the folder in
which you want to save the message.
■ Instant messaging (IM)
Instant messaging (network service) is a way to send short, simple text
messages to online users.
Before you can use instant messaging, you must subscribe to the
service. To check the availability and costs, and to subscribe to the
service, contact your network operator or service provider, from whom
you also receive your unique ID, password, and settings.
To set the required settings for the instant messaging service, see
Connect. settings in “Access the IM menu,” p. 33. The icons and texts on
the display may vary, depending on the instant messaging service.
32
M e s s a g e s
Depending on the network, the active instant messaging conversation
may consume the phone battery faster, and you may need to connect
the phone to a charger.
Access the IM menu
To access the menu while still offline, select Menu > Messaging >
Instant messages. If more than one set of connection settings for the
instant messaging service is available, select the desired one. If there is
only one set defined, it is selected automatically.
The following options are shown:
Login — to connect to the instant messaging service
Saved convers. — to view, erase, or rename the instant messaging
conversations that you have saved during the instant messaging session
Connect. settings — to edit the settings needed for messaging and
presence connection
Connect to the IM service
To connect to the instant messaging service, open the Instant messages
menu, activate an instant messaging service, and select Login. When the
phone has successfully connected, Logged in is displayed.
To disconnect from the instant messaging service, select Logout.
Start an IM session
Open the Instant messages menu, and connect to the service. Start the
service in different ways.
• Select Conversations to view the list of new and read instant
messages or invitations for instant messaging during the active
instant messaging session. Scroll to the message or invitation that
you want, and select Open to read the message.
indicates the new and
the new and the read instant messages.
indicates the invitations.
read group messages.
indicates
33
M e s s a g e s
The icons and texts on the display may vary, depending on the
instant messaging service.
• Select IM contacts to view the contacts that you have added. Scroll
to the contact with whom you would like to chat, and select Chat or
Open if a new contact is shown in the list. To add contacts, see
“Contacts for IM,” p. 36.
indicates the online and
contacts memory.
the offline contacts in the phone
indicates a
indicates a blocked contact.
contact that has been sent a new message.
• Select Groups > Public groups to display the list of bookmarks to
public groups provided by the network operator or service provider.
To start an instant messaging session with a group, scroll to a group,
and select Join. Enter your screen name that you want to use in the
conversation. When you have successfully joined the group
conversation, you can start a group conversation. To create a private
group, see “Groups,” p. 36.
• Select Search > Users or Groups to search for other instant
messaging users or public groups on the network by phone number,
screen name, e-mail address, or name. If you select Groups, you can
search for a group by a member in the group or by group name, topic,
or ID. To start the conversation when you have found the user or the
group that you want, select Options > Chat or Join group.
To start a conversation from Contacts, see “View the subscribed
names,” p. 46.
Accept or reject an invitation
In the standby mode, when you are connected to the instant messaging
service and you receive a new invitation, New invitation received is
displayed. To read it, select Read. If more than one invitation is received,
scroll to the invitation you want, and select Open. To join the private
group conversation, select Accept, and enter the screen name; or to
reject or delete the invitation, select Options > Reject or Delete.
34
M e s s a g e s
Read a received instant message
In the standby mode, when you are connected to the instant messaging
service, and you receive a new message that is not a message associated
with an active conversation, New instant message is displayed. To read
it, select Read. If you receive more than one message, scroll to the
message, and select Open.
New messages received during an active conversation are held in
Instant messages > Conversations. If you receive a message from
someone who is not in IM contacts, the sender ID is displayed. To save a
new contact that is not in the phone memory, select Options > Save
contact.
Participate in a conversation
To join or start an instant messaging session, select Write. Write your
message, and select Send or press the call key to send it.
Select Options to access available options: View conversation, Save
contact, Group members, Block contact, and End conversation.
Edit your availability status
1. Open the Instant messages menu, and connect to the instant
messaging service.
2. To view and edit your own availability information or screen name,
select Settings.
3. To allow all the other instant messaging users to see you when you
are online, select Availability > Available for all.
To allow only the contacts on your instant messaging contact list to
see you when you are online, select Availability > Avail. for contacts.
To appear as being offline, select Availability > Appear offline.
When you are connected to the instant messaging service,
indicates
that you are online, and indicates that you are not visible to others.
35
M e s s a g e s
Contacts for IM
To add contacts to the instant messaging contacts list, connect to the
instant messaging service, and select IM contacts. To add a contact to
the list, select Options > Add contact, or if you have no contacts added,
select Add. Select Enter ID manually, Search from serv., Copy from server,
or By mobile number.
Scroll to a contact, and to start a conversation, select Chat or Options >
Contact info, Block contact or Unblock contact, Add contact, Remove
contact, Change list, Copy to server, or Availability alerts.
Block and unblock messages
To block messages, connect to the instant messaging service, and select
Conversations > IM contacts; or join or start a conversation. Scroll to
the contact from whom you want to block incoming messages, and
select Options > Block contact > OK.
To unblock the messages, connect to the instant messaging service, and
select Blocked list. Scroll to the contact from whom you want to unblock
the messages, and select Unblock.
Groups
You can create your own private groups for an instant messaging
conversation, or use the public groups provided by the service provider.
The private groups exist only during an instant messaging conversation.
The groups are saved on the server of the service provider. If the server
you are logged on to does not support group services, all group-related
menus are dimmed.
Public groups
You can bookmark public groups that your service provider may
maintain. Connect to the instant messaging service, and select Public
groups. Scroll to a group with which you want to chat, and select Join. If
you are not in the group, enter your screen name as your nickname for
the group. To delete a group from your group list, select Options >
Delete group.
36
M e s s a g e s
To search for a group, select Groups > Public groups > Search groups.
You can search for a group by a member in the group, group name, topic,
or ID.
Private groups
group. Enter the name for the group and the screen name that you want
to use. Mark the private group members in the contacts list, and write
an invitation.
■ E-mail application
The e-mail application allows you to access your compatible e-mail
account from your phone when you are not in the office or at home. This
e-mail application is different from the SMS and MMS e-mail function.
Your phone supports POP3 and IMAP4 e-mail servers. Before you can
send and retrieve any e-mail, you may need to do the following:
• Obtain a new e-mail account or use the current one. For availability
of your e-mail account, contact your e-mail service provider.
• For the settings required for e-mail, contact your e-mail service
provider. You may receive the e-mail configuration settings as a
configuration message. See “Configuration settings service,” p. 10.
You can also enter the settings manually. See “Configuration,” p. 58.
To activate the e-mail settings, select Menu > Messaging > Message
settings > E-mail messages. See “E-mail,” p. 41.
This application does not support keypad tones.
Write and send an e-mail
1. Select Menu > Messaging > E-mail > Create e-mail.
2. Enter the recipient’s e-mail address, a subject, and the e-mail
message.
To attach a file to the e-mail, select Options > Attach and the file in
Gallery.
3. Select Send > Send now.
37
M e s s a g e s
Download e-mail
1. To access the e-mail application, select Menu > Messaging > E-mail.
2. To download e-mail messages that have been sent to your e-mail
account, select Retrieve.
To download new e-mail messages and to send e-mail that has been
saved in the Outbox folder, select Options > Retrieve and send.
To download first the headings of the new e-mail messages that
have been sent to your e-mail account, select Options > Check new
e-mail. Then, to download the selected e-mail, mark the desired
ones, and select Options > Retrieve.
3. Select the new message in Inbox. To view it later, select Back.
indicates an unread message.
Read and reply to e-mail
Important: Exercise caution when opening messages. E-mail
messages may contain malicious software or otherwise be harmful to
your device or PC.
Select Menu > Messaging > E-mail > Inbox and the desired message.
While reading the message, select Options to view the available options.
To reply to an e-mail, select Reply > Empty screen or Original text. To
reply to many, select Options > Reply to all. Confirm or edit the e-mail
address and subject; then write your reply. To send the message, select
Send > Send now.
Inbox and other folders
Your phone saves e-mail that you have downloaded from your e-mail
account in the Inbox folder. Other folders contains the following folders:
Drafts for saving unfinished e-mail, Archive for organizing and saving
your e-mail, Outbox for saving e-mail that has not been sent, and Sent
items for saving e-mail that has been sent.
To manage the folders and their e-mail content, select Options >
Manage folder.
38
M e s s a g e s
Delete e-mail messages
Select Menu > Messaging > E-mail > Options > Manage folder and the
desired folder. Mark the messages that you want to delete. To delete
them, select Options > Delete. Deleting an e-mail from your phone does
not delete it from the e-mail server. To set the phone to delete the
e-mail also from the e-mail server, select Menu > Messaging > E-
mail > Options > Extra settings > Leave copy: > Delete retr. msgs.
■ Voice messages
The voice mailbox is a network service and you may need to subscribe to
it. For details, contact your service provider.
To call your voice mailbox, select Menu > Messaging > Voice
messages > Listen to voice messages. To enter, search for, or edit your
voice mailbox number, select Voice mailbox number. If supported by the
network,
indicates that there are new voice messages. Select
Listen to call your voice mailbox number.
■ Info messages
Select Menu > Messaging > Info messages. With the Info messages
network service, you can receive messages on various topics from your
service provider. To check availability, topics, and the relevant topic
numbers, contact your service provider.
■ Service commands
Select Menu > Messaging > Service commands. Write and send service
requests (also known as USSD commands) to your service provider, such
as activation commands for network services.
■ Delete messages
To delete all messages from a folder, select Menu > Messaging > Delete
messages and the folder from which you want to delete the messages.
Select Yes, and if the folder contains unread messages, the phone asks
whether you want to delete them also. Select Yes again.
39
M e s s a g e s
■ Message settings
Text and SMS e-mail
The message settings affect the sending, receiving, and viewing of
messages.
Select Menu > Messaging > Message settings > Text messages and
from the following options:
Sending profile — If more than one message profile set is supported by
your SIM card, select the set you want to change.
The following options may be available: Message centre number
(delivered from your service provider), Messages sent via, Message
validity, Default recipient number (text messages) or E-mail server
(e-mail), Delivery reports, Use packet data, Reply via same centre
(network service), and Rename sending profile.
Save sent messages > Yes — Set the phone to save the sent text
messages in the Sent items folder.
Automatic resending > On — The phone automatically attempts to
resend a text message, if the sending has failed.
Multimedia
The message settings affect the sending, receiving, and viewing of
multimedia messages.
Select Menu > Messaging > Message settings > Multimedia msgs. and
from the following options:
Save sent messages > Yes — to set the phone to save sent multimedia
messages in the Sent items folder
Delivery reports — to ask the network to send delivery reports about your
messages (network service)
Default slide timing — to define the default time between slides in
multimedia messages
Allow multimedia reception > Yes or No — to receive or to block the
multimedia message. If you select In home network, you cannot receive
multimedia messages when outside your home network.
40
M e s s a g e s
Incoming multimedia messages > Retrieve, Retrieve manually, or Reject
— to allow the reception of multimedia messages automatically,
manually after being prompted, or to reject the reception
Configuration settings > Configuration — Only the configurations that
support multimedia messaging are shown. Select a service provider,
Default, or Personal config. for multimedia messaging. Select Account
and a multimedia messaging service account contained in the active
configuration settings.
Allow adverts — to receive or reject advertisements. This setting is not
shown if Allow multimedia reception is set to No.
E-mail
The settings affect the sending, receiving, and viewing of e-mail.
You may receive the configuration settings for the e-mail application as
a configuration message. See “Configuration settings service,” p. 10.
You can also enter the settings manually. See “Configuration,” p. 58.
To activate the settings for the e-mail application, select Menu >
Messaging > Message settings > E-mail messages and from the
following options:
Configuration — Select the set that you want to activate.
Account — Select an account provided by the service provider.
My name — Enter your name or nickname.
E-mail address — Enter your e-mail address.
Include signature — You can define a signature that is automatically
added to the end of your e-mail when you write your message.
Reply-to address — Enter the e-mail address to which you want the
replies to be sent.
SMTP user name — Enter the name that you want to use for outgoing
mail.
SMTP password — Enter the password that you want to use for outgoing
mail.
41
M e s s a g e s
Display terminal window — Select Yes to perform manual user
authentication for intranet connections.
Incoming server type — Select POP3 or IMAP4, depending on the type of
e-mail system that you use. If both types are supported, select IMAP4.
Incoming mail settings — Select available options for POP3 or IMAP4.
Font size and smileys
Select Menu > Messaging > Message settings > Other settings. To
change the font size for reading and writing messages, select Font size.
To replace character-based smileys with graphical ones, select
Graphical smileys > Yes.
■ Message counter
Select Menu > Messaging > Message counter for approximate
information on your recent communications.
42
C o n t a c t s
7. Contacts
You can save names and phone numbers (Contacts) in the
phone memory and in the SIM card memory.
The phone memory may save contacts with numbers and text items. You
can also save an image for a certain number of names.
Names and numbers saved in the SIM card memory are indicated by
.
■ Search for a contact
Select Menu > Contacts > Names. Scroll through the list of contacts, or
■ Save names and phone numbers
Names and numbers are saved in the used memory. Select Menu >
Contacts > Names > Options > Add new contact. Enter the name and
the phone number.
■ Save numbers, items, or an image
In the phone memory for contacts, you can save different types of phone
numbers and short text items per name.
The first number you save is automatically set as the default number. It
is indicated with a frame around the number type indicator (for
example,
). When you select a name (for example, to make a call),
the default number is used unless you select another number.
1. Ensure that the memory in use is Phone or Phone and SIM. See
“Settings,” p. 47.
2. Scroll to the name to which you want to add a new number or text
item, and select Details > Options > Add detail.
3. To add a number, select Number and a number type.
To add another detail, select a text type or an image from Gallery.
43
C o n t a c t s
To search for an ID from the server of your service provider if you
have connected to the presence service, select User ID > Search. See
“My presence,” p. 45. If only one ID is found, it is automatically
saved. Otherwise, to save the ID, select Options > Save. To enter the
ID, select Enter ID manually.
4. Enter the number or text item; to save it, select OK.
5. To return to the standby mode, select Back > Exit.
■ Copy contacts
Search for the contact you want to copy, and select Options > Copy.
You can copy names and phone numbers from the phone contact
memory to the SIM card memory, or vice versa. The SIM card memory
can save names with one phone number attached to them.
■ Edit contact details
1. Search for the contact you want to edit, select Details, and scroll to
the desired name, number, text item, or image.
2. To edit a name, number, or text item, or to change an image, select
Options > Edit name, Edit number, Edit detail, or Change image.
To change the number type, scroll to the desired number, and select
Options > Change type. To set the selected number as the default
number, select Set as default.
You cannot edit an ID when it is on the IM contacts or Subscribed
names list.
■ Delete contacts or contact details
To delete all the contacts and the details attached to them from the
phone or SIM card memory, select Menu > Contacts > Delete all
contacts > From phone mem. or From SIM card. Confirm with the
security code.
To delete a contact, search for the desired contact, and select Options >
Delete contact.
44
C o n t a c t s
To delete a number, text item, or an image attached to the contact,
search for the contact, and select Details. Scroll to the desired detail,
and select Options > Delete > Delete number, Delete detail, or Delete
image. Deleting an image from contacts does not delete it from Gallery.
■ Business cards
You can send and receive a person’s contact information from a
compatible device that supports the vCard standard as a business card.
To send a business card, search for the contact whose information you
want to send, and select Details > Options > Send bus. card > Via
multimedia, Via text message, or Via infrared.
When you have received a business card, select Show > Save to save the
Exit > Yes.
■ My presence
With the presence service (network service) you can share your presence
status with other users with compatible devices and access to the
service. Presence status includes your availability, status message, and
personal logo. Other users who have access to the service and who
request your information are able to see your status. The requested
information is shown in Subscribed names in the viewers’ Contacts
menu. You can personalize the information that you want to share with
others and control who can see your status.
Before you can use presence, you must subscribe to the service. To check
the availability and costs, and to subscribe to the service, contact your
network operator or service provider, from whom you also receive your
unique ID, password, and the settings for the service. See
“Configuration,” p. 58.
While you are connected to the presence service, you can use the other
functions of the phone; the presence service is active in the background.
If you disconnect from the service, your presence status is shown for a
certain amount of time to viewers, depending on the service provider.
45
C o n t a c t s
Select Menu > Contacts > My presence and from the following options:
Connect to 'My presence' service or Disconnect from service — to
connect to or disconnect from the service
View my presence — to view the status in Private pres. and Public
presence
Edit my presence — to change your presence status. Select My
availability, My presence message, My presence logo, or Show to.
My viewers > Current viewers, Private list, or Blocked list
Settings > Show current pres. in standby, Synchronise with profiles,
Connection type, or Presence settings
■ Subscribed names
You can create a list of contacts whose presence status information you
want to be aware of. You can view the information if it is allowed by the
contacts and the network. To view these subscribed names, scroll
through the contacts or use the Subscribed names menu.
Ensure that the memory in use is Phone or Phone and SIM. See
“Settings,” page 47.
To connect to the presence service, select Menu > Contacts > My
presence > Connect to 'My presence' service.
Add contacts to the subscribed names
1. Select Menu > Contacts > Subscribed names.
2. If you have no contacts on your list, select Add. Otherwise, select
Options > Subscribe new. The list of your contacts is shown.
3. Select a contact from the list, and if the contact has an user ID saved,
the contact is added to the subscribed names list.
View the subscribed names
To view the presence information, see “Search for a contact,” p. 43.
1. Select Menu > Contacts > Subscribed names.
46
C o n t a c t s
The status information of the first contact on the subscribed names
list is displayed. The information that the person wants to give to the
others may include text and some of the following icons:
,
, or indicates that the person is available, not visible to
others, or not available.
indicates that the person’s presence information is not available.
2. Select Details to view the details of the selected contact; or select
Options > Subscribe new, Chat, Send message, Send bus. card, or
Unsubscribe.
Unsubscribe a contact
To unsubscribe a contact from the Contacts list, select the contact and
Details > the user ID > Options > Unsubscribe > OK.
To unsubscribe, use the Subscribed names menu. See “View the
subscribed names,” p. 46.
■ Settings
Select Menu > Contacts > Settings and from the following options:
Memory in use — to select SIM card or phone memory for your contacts.
Select Phone and SIM to recall names and number from both memories.
In that case, when you save names and numbers, they are saved in the
phone memory.
Contacts view — to select how the names and numbers in contacts are
displayed
Memory status — to view the free and used memory capacity
■ Groups
Select Menu > Contacts > Groups to arrange the names and phone
numbers saved in the memory into caller groups with different ringing
tones and group images.
47
C o n t a c t s
■ Voice dialing
You can make a phone call by saying a voice tag that has been added to
a phone number. Any spoken words, such as a name, can be a voice tag.
The number of voice tags you can create is limited.
Before using voice tags, note the following:
•
Voice tags are not language-dependent. They are dependent on the speaker's
voice.
•
•
You must say the name exactly as you said it when you recorded it.
Voice tags are sensitive to background noise. Record voice tags and use them
in a quiet environment.
•
Very short names are not accepted. Use long names and avoid similar names
for different numbers.
Note:Using voice tags may be difficult in a noisy environment or during
an emergency, so you should not rely solely upon voice dialling in all
circumstances.
Add and manage voice tags
Save or copy the contacts to the phone memory for which you want to
add a voice tag. You can also add voice tags to the names in the SIM
card, but if you replace your SIM card with a new one, you must first
delete the old voice tags before you can add new ones.
1. Search for the contact to which you want to add a voice tag.
2. Select Details, scroll to the desired phone number, and select
Options > Add voice tag.
3. Select Start, and say clearly the words you want to record as a voice
tag. After recording, the phone plays the recorded tag.
appears behind the phone number with a voice tag in Contacts.
To check the voice tags, select Menu > Contacts > Voice tags. Scroll to
the contact with the voice tag that you want, and select an option to
listen to, delete, or change the recorded voice tag.
48
C o n t a c t s
Make a call with a voice tag
If the phone has an application running that is sending or receiving data
using a packet data connection, you must end the application before
voice dialing.
1. In the standby mode, press and hold the volume down key. A short
tone is heard, and Speak now is displayed.
2. Say the voice tag clearly. The phone plays the recognized voice tag,
and dials the phone number of the voice tag after 1.5 seconds.
If you are using a compatible headset with the headset key, press and
hold the headset key to start the voice dialing.
■ Speed dials
To assign a number to a speed-dialing key, select Menu > Contacts >
Speed dials, and scroll to the speed-dialing number that you want.
Select Assign, or if a number has already been assigned to the key,
select Options > Change. Select Search, the name, then the number you
want to assign. If the Speed dialling function is off, the phone asks
whether you want to activate it. See also Speed dialling in “Call,” p. 54.
To make a call using the speed-dialing keys, see “Speed dialing,” p. 20.
■ Info, service, and my numbers
Select Menu > Contacts and from the following functions:
Info numbers — to call the information numbers of your service provider
if the numbers are included on your SIM card (network service)
Service numbers — to call the service numbers of your service provider if
the numbers are included on your SIM card (network service)
My numbers — to view the phone numbers assigned to your SIM card, if
the numbers are included on your SIM card
49
L o g
8. Log
The phone registers the phone numbers of identified
missed, received, and dialed calls; and the approximate length of your
calls. Select Menu > Log.
The phone registers if it is switched on and within the network service
area, and the network supports these functions.
■ Recent calls lists
When you select Options in the Missed calls, Received calls, Dialled
numbers, or Message recipients menu, you can view the time of the call;
edit, view, or call the registered phone number; add it to the memory; or
delete it from the list. You can also send a text message. To delete the
recent calls lists, select Menu > Log > Clear log lists.
■ Counters and timers
Note: The actual invoice for calls and services from your service
provider may vary, depending upon network features, rounding off for
billing, taxes, and so forth.
Some timers, including the life timer, may be reset during service or
software upgrades.
Select Menu > Log > Call duration, Packet data counter, or Packet data
conn. timer for approximate information on your recent
communications.
50
S e t t i n g s
9. Settings
■ Profiles
Your phone has various setting groups, called profiles, for which you can
customize the phone tones for different events and environments.
Select Menu > Settings > Profiles. Scroll to a profile, and select it.
To activate the selected profile, select Activate.
To set the profile to be active until a certain time up to 24 hours, select
Timed, and set the time the profile setting shall end. When the time set
active.
To personalize the profile, select Personalise. Select the setting you want
to change, and make the changes. To change your presence status
information, select My presence > My availability or My presence
message. The My presence menu is available if you set Synchronise with
profiles to On. See “My presence,” p. 45.
■ Themes
A theme contains many elements for personalizing your phone, such as
wallpaper, screen saver, color scheme, and a ringing tone.
Select Menu > Settings > Themes and from the following options:
Select theme — to set a theme in your phone. A list of folders in Gallery
opens. Open the Themes folder, and select a theme.
Theme downloads — to open a list of links to download more themes.
See “Download files,” p. 85.
■ Tones
You can change the settings of the selected active profile.
Select Menu > Settings > Tones. Select and change Incoming call alert,
Ringing tone, Ringing volume, Vibrating alert, Push to talk settings,
Message alert tone, Instant message alert tone, Keypad tones, and
51
S e t t i n g s
Warning tones. You can find the same settings in the Profiles menu. See
“Profiles,” p. 51.
If you select the highest ringing tone level, the ringing tone reaches its highest
level after a few seconds.
To set the phone to ring only for calls from phone numbers that belong
to a selected caller group, select Alert for. Scroll to the caller group you
want or All calls, and select Mark.
■ Lights
Select Menu > Settings > Lights > Light effects > On to activate the
light effects of the phone, for example, as a reminder for missed calls.
■ My shortcuts
With personal shortcuts, you get quick access to often used functions of
the phone. To manage the shortcuts, select Menu > Settings > My
shortcuts and from the following options:
Right selection key — to select a function from the list for the right
selection key. See also “Standby mode,” p. 17. This menu may not be
shown, depending on your service provider.
Navigation key — to select shortcut functions for the navigation key.
Scroll to the desired navigation key, select Change and a function from
the list. To remove a shortcut function from the key, select (empty). To
reassign a function for the key, select Assign. This menu may not be
shown, depending on your service provider.
Voice commands — to activate phone functions by saying a voice tag.
Select a folder, scroll to a function to which you want to add a voice tag,
and select Add.
indicates a voice tag. To activate a voice command,
see “Make a call with a voice tag,” p. 49.
■ Display
Select Menu > Settings > Display and from the following options:
Wallpaper — to add the background image to the display in the standby
mode. To activate or deactivate the wallpaper, select On or Off. Select
52
S e t t i n g s
Select wallpaper to select an image from the Gallery or Select slide set
and a folder in the Gallery to use the images in the folder as a slide set.
To download more images for wallpaper, select Graphic downloads.
Screen saver > On — to activate the screen saver for the main display. To
set the time after which the screen saver is activated, select Time-out.
To select a graphic for the screen saver, select Image and an image or a
graphic from the Gallery. Select Slide set and a folder in the Gallery to
use the images in the folder as a slide set. To download more images for
the screen saver, select Graphic downloads.
Power saver > On — to save some battery power. A digital clock is
displayed when no function of the phone is used for a certain time.
Colour schemes — to change the color of the menu background and the
signal and battery bars
Standby mode font colour — to select the color for the texts on the
display in the standby mode
Operator logo — to set your phone to display or hide the operator logo.
The menu is dimmed if you have not saved the operator logo. For more
information on availability of an operator logo, contact your network
operator or service provider.
■ Time and date
To change the time, time zone, and date settings, select Menu >
Settings > Time and date > Clock, Date, or Auto-update of date & time
(network service).
When traveling to a different time zone, select Menu > Settings > Time
and date > Clock > Time zone and the time zone of your location in
terms of the time difference with respect to Greenwich Mean Time
(GMT) or Universal Time Coordinated (UTC). The time and date are set
according to the time zone and enable your phone to display the correct
sending time of received text or multimedia messages. For example,
GMT -5 denotes the time zone for New York (USA), 5 hours west of
Greenwich/London (UK).
53
S e t t i n g s
■ Call
Automatic volume control — to set the phone to automatically adjust
the output volume according to the background noise
Call divert (network service) — to divert your incoming calls. You may
not be able to divert your call, if some call barring functions are active.
See Call barring service in “Security,” p. 59.
Anykey answer > On — to answer an incoming call, briefly press any key,
except the end key and the left and right selection keys.
Automatic redial > On — to set your phone to make a maximum of 10
attempts to connect the call after an unsuccessful call attempt
Speed dialling > On — to activate speed dialling. To set up speed dialling,
see “Speed dials,” p. 49. To dial, press and hold the corresponding
number key.
Call waiting > Activate — to set the network to notify you of an
incoming call while you have a call in progress (network service). See
“Call waiting,” p. 21.
Summary after call > On — to briefly display the approximate duration
and cost (network service) of the call after each call
Send my caller ID (network service) > Set by network, Yes, or No
Line for outgoing calls (network service) — to select the phone line 1 or 2
to make calls, if supported by your SIM card
■ Phone
Select Menu > Settings > Phone and from the following options:
Phone language — to set the display and writing language
Memory status — to view the free memory and the used memory in
Gallery, Messaging, and Applications
Automatic keyguard — to set the keypad of your phone to lock
automatically after a preset time delay when the phone is in the standby
mode and no function of the phone has been used. Select On, and set
the time from 5 seconds to 60 minutes.
54
S e t t i n g s
Security keyguard — to set the phone to ask for the security code when
you unlock the keyguard. Enter the security code, and select On.
When the keyguard is on, calls still may be possible to the official emergency
number programmed into your device.
Cell info display > On — to receive information from the network
operator depending on the network cell used (network service)
Welcome note — to enter a welcome note to be shown briefly when the
phone is switched on
Operator selection > Automatic — to set the phone automatically to
select one of the cellular networks available in your area. With Manual,
you can select a network that has a roaming agreement with your home
network operator.
Confirm SIM service actions — See “SIM services,” p. 90.
Help text activation — to select whether the phone shows help texts
Start-up tone — to select whether the phone plays a start-up tone when
the phone is switched on
■ Connectivity
You can connect your phone to compatible devices using an infrared
connection. You can also define the settings for packet data dial-up
connections.
Infrared
You can send or receive data to or from a compatible phone or data
device (for example, a computer) through the infrared (IR) port of your
phone. To use an IR connection, the device with which you want to
establish a connection must be IrDA compliant.
Do not point the IR (infrared) beam at anyone's eyes or allow it to interfere with
other IR devices. Infrared devices are Class 1 laser products.
When sending or receiving data, ensure that the IR ports of the sending
and receiving devices are pointing at each other and that there are no
obstructions between the devices.
55
S e t t i n g s
To activate the IR port of your phone to receive data using IR, select
Menu > Settings > Connectivity > Infrared.
To deactivate the IR connection, select Menu > Settings >
Connectivity > Infrared. When the phone displays Deactivate infrared?,
select Yes.
If data transfer is not started within 2 minutes after the activation of
the IR port, the connection is canceled and must be started again.
IR connection indicator
When
is shown continuously, the IR connection is activated, and
your phone is ready to send or receive data through its IR port.
When blinks, your phone is trying to connect to the other device, or
a connection has been lost.
Packet data (EGPRS)
Enhanced general packet radio service (EGPRS), packet data, is a
network service that allows mobile phones to send and receive data over
an Internet protocol (IP)-based network. It enables wireless access to
data networks such as the Internet.
The applications that may use packet data are MMS, browsing sessions,
e-mail, remote SyncML, Java application downloading, push to talk,
instant messaging, and the PC dial-up.
To define how to use the service, select Menu > Settings >
Connectivity > Packet data > Packet data connection.
Select When needed to set the packet data connection to be established
when an application needs it. The connection will be closed when the
application is ended.
Select Always online to set the phone to automatically connect to an
packet data network when it is switched on.
indicates a packet data connection.
56
S e t t i n g s
Modem settings
You can connect the phone using an IR or a data cable (CA-42)
connection to a compatible PC, and use the phone as a modem to enable
packet data connectivity from the PC.
To define the settings for connections from the PC, select Menu >
Settings > Connectivity > Packet data > Packet data settings > Active
access point, activate the access point you want to use, and select Edit
active access point. Select Alias for access point, and enter a nickname
for the currently selected access point. Select Packet data access point,
and enter the access point name (APN) to establish a connection to an
EGPRS network.
You can also set the dial-up service settings (access point name) on your
PC using the Nokia Modem Options software. See “Nokia PC Suite,”
p. 91. If you have set the settings both on the PC and on your phone, the
PC settings are used.
■ Enhancements
This menu is shown only if the phone is or has been connected to a
compatible mobile enhancement.
Select Menu > Settings > Enhancements. You can select an
enhancement menu if the corresponding enhancement is, or has been,
connected to the phone. Depending on the enhancement, select from
the following options:
Default profile — to select the profile that you want to be automatically
activated when you connect to the selected enhancement
Automatic answer — to set the phone to answer an incoming call
automatically after 5 seconds. If Incoming call alert is set to Beep once
or Off, automatic answer is off.
Lights — to set the lights permanently On. Select Automatic to set the
lights on for 15 seconds after a keypress.
Text phone > Use text phone > Yes — to use the text phone settings
instead of headset or loopset settings
57
S e t t i n g s
■ Configuration
You can configure your phone with settings that are required for certain
services to function correctly. The services are browser, multimedia
messaging, remote Internet server synchronization, presence, and
e-mail application. Get the settings from your SIM card, from a service
provider as a configuration message, or enter your personal settings
manually. You can store configuration settings from up to 20 service
providers in the phone and manage them within this menu.
To save the configuration settings received by a configuration message
from a service provider, see “Configuration settings service,” p. 10.
Select Menu > Settings > Configuration and from the following
options:
Default configuration settings — to view the service providers saved in
the phone. Scroll to a service provider, and select Detailsto view the
applications that the configuration settings of this service provider
support. To set the configuration settings of the service provider as
default settings, select Options > Set as default. To delete configuration
settings, select Delete.
Activate default in all applications — to activate the default
configuration settings for supported applications
Preferred access point — to view the saved access points. Scroll to an
access point, and select Options > Details to view the name of the
service provider, data bearer, and packet data access point or GSM
dial-up number.
Connect to service provider support — to download the configuration
settings from your service provider
Personal configuration settings — to add new personal accounts for
various services manually, and to activate or delete them. To add a new
personal account if you have not added any, select Add new; otherwise,
select Options > Add new. Select the service type, and select and enter
each of the required parameters. The parameters differ according to the
selected service type. To delete or activate a personal account, scroll to
it, and select Options > Delete or Activate.
58
S e t t i n g s
■ Security
When security features that restrict calls are in use (such as call barring, closed
user group and fixed dialing) calls still may be possible to the official emergency
number programmed into your device.
Select Menu > Settings > Security and from the following options:
PIN code request — to set the phone to ask for your PIN or UPIN code
every time the phone is switched on. Some SIM cards do not allow the
code request to be turned off.
Call barring service (network service) — to restrict incoming calls to and
outgoing calls from your phone. A barring password is required.
Fixed dialling — to restrict your outgoing calls to selected phone
numbers if this function is supported by your SIM card
Closed user group (network service) — to specify a group of people
whom you can call and who can call you
Security level > Phone — the phone asks for the security code whenever
a new SIM card is inserted into the phone. Select Memory, and the
phone asks for the security code when SIM card memory is selected and
you want to change the memory in use.
Access codes — to change the security code, PIN code, UPIN code, PIN2
code, and barring password
Code in use — to select whether the PIN code or UPIN code is active
Pin2 code request — to select whether the PIN2 code is required when
using a phone feature that is covered by the PIN2 code
■ Restore factory settings
To reset some of the menu settings to their original values, select
Menu > Settings > Restore factory sett.. Enter the security code. The
data you have entered or downloaded are not deleted, for example, the
names and phone numbers saved in Contacts.
59
O p e r a t o r m e n u
10. Operator menu
This menu lets you access a portal to services provided by your network
operator. The name and the icon depend on the operator. For more
information, contact your network operator. If this menu is not shown,
the following menu numbers change accordingly.
The operator can update this menu with a service message. For more
information, see “Service inbox,” p. 85.
60
G a l l e r y
11. Gallery
In this menu you can manage graphics, images, recordings,
video clips, themes, and tones. These files are arranged in folders.
Your phone supports an activation key system to protect acquired
content. Always check the delivery terms of any content and activation
key before acquiring them, as they may be subject to a fee.
Copyright protections may prevent some images, music (including ringing tones),
and other content from being copied, modified, transferred or forwarded.
The files stored in Gallery use a memory that may have a capacity of
about 3 MB.
To see the list of folders, select Menu > Gallery.
To see the available options of a folder, select a folder and Options.
To view the list of files in a folder, select a folder and Open.
To see the available options of a file, select a file and Options.
61
M e d i a
12. Media
Copyright protections may prevent some images, music (including ringing tones),
and other content from being copied, modified, transferred or forwarded.
■ Camera
You can take photos or record video clips with the built-in camera. The
camera produces pictures in JPEG format and video clips in 3GP format.
When taking and using images or video clips, obey all laws and respect local
customs as well as privacy and legitimate rights of others, including copyrights.
This device supports an image capture resolution of 640 x 480 pixels. The image
resolution in these materials may appear different.
Take a photo
To take a photo, select Menu > Media > Camera > Capture. The phone
saves the photo in Gallery > Images. To take another photo, select Back;
to send the photo as a multimedia message, select Send. To view the
options, select Options.
Record a video clip
Select Menu > Media > Camera. To select the video mode, scroll left or
right, or select Options > Video; to start the recording, select Record. To
pause the recording, select Pause; to resume the recording, select
Continue. To stop the recording, select Stop. The phone saves the
recording in Gallery > Video clips. To view the options, select Options.
■ Radio
The FM radio depends on an antenna other than the wireless device antenna. A
compatible headset or enhancement needs to be attached to the device for the
FM radio to function properly.
Warning: Listen to music at a moderate level. Continuous exposure to
high volume may damage your hearing. Do not hold the device near
your ear when the loudspeaker is in use, because the volume may be
extremely loud.
62
M e d i a
Select Menu > Media > Radio. To use the graphical keys
,
,
,
or on the display, scroll left or right to the desired key, and select it.
To change the volume, press the volume keys.
Save radio stations
1. To start the station search, select and hold
or
. To change
or
the radio frequency in 0.05 MHz steps, briefly press
.
2. To save the station to a memory location, 1 to 9, press and hold the
corresponding number key. To save the station in the memory
location from 10 to 20, press briefly 1 or 2, and press and hold the
desired number key, 0 to 9.
3. Enter the name of the station, and select OK.
Listen to the radio
Select Menu > Media > Radio. To scroll to the desired station, select
or
or press the headset key. To select a radio station location, briefly
press the corresponding number keys.
Select Options and from the following options:
Switch off — to turn off the radio
Save station — to save a new station, and enter the station name
Stations — to select the list of saved stations. To delete or rename a
station, scroll to the desired station, and select Options > Delete station
or Rename.
Mono output or Stereo output — to listen to the radio in monophonic
sound or in stereo
Loudspeaker or Headset — to listen to the radio using the loudspeaker or
headset. Keep the headset connected to the phone. The lead of the
headset functions as the radio antenna.
Set frequency — to enter the frequency of the desired radio station
You can normally make a call or answer an incoming call while listening
to the radio. During the call, the volume of the radio is muted.
63
M e d i a
When an application using a packet data or HSCSD connection is
sending or receiving data, it may interfere with the radio.
■ Recorder
You can record pieces of speech, sound, or an active call for up to
5 minutes. The actual recording time depends on the available memory
space.
The recorder cannot be used when a data call or packet data connection is active.
Record sound
1. Select Menu > Media > Recorder.
To use the graphical keys,
,
, or
, on the display, scroll left or
right to the desired key, and select it.
2. To start the recording, select . To start the recording during a call,
select Options > Record. While recording a call, all parties to the call
hear a faint beeping sound about every 5 seconds. When recording a
call, hold the phone in the normal position near to your ear.
3. To end the recording, select
. The recording is saved in Gallery >
Recordings.
4. To listen to the latest recording, select Options > Play last recorded.
5. To send the last recording using a multimedia or audio message or IR,
select Options > Send last recorded.
List of recordings
Select Menu > Media > Recorder > Options > Recordings list. The list of
folders in the Gallery is shown. Open Recordings to see the list with
recordings. Select Options to select options for files in the Gallery. See
“Gallery,” p. 61.
64
O r g a n i z e r
13. Organizer
■ Alarm clock
You can set the phone to alarm at a desired time. Select Menu >
Organiser > Alarm clock.
To set the alarm, select Alarm time, and enter the alarm time. To change
the alarm time when the alarm time is set, select On. To set the phone to
alert you on selected days of the week, select Repeat alarm.
To select the alarm tone or set a radio station as the alarm tone, select
Alarm tone. If you select the radio as an alarm tone, connect the headset
to the phone. The phone uses the last station you listened to as the
alarm, and the alarm plays through the loudspeaker. If you remove the
headset or switch off the phone, the default alarm tone replaces the
radio.
To set a snooze time-out, select Snooze time-out.
Stop the alarm
The phone sounds an alert tone, and flashes Alarm! and the current time
on the display, even if the phone was switched off. To stop the alarm,
select Stop. If you let the phone continue to sound the alarm for a
minute or select Snooze, the alarm stops for the selected snooze
time-out and then resumes.
If the alarm time is reached while the device is switched off, the device switches
itself on and starts sounding the alarm tone. If you select Stop, the device asks
whether you want to activate the device for calls. Select No to switch off the
device or Yes to make and receive calls. Do not select Yes when wireless phone
use may cause interference or danger.
■ Calendar
Select Menu > Organiser > Calendar.
The current day is indicated by a frame. If there are any notes set for the
day, the day is in bold type. To view the day notes, select View. To view a
65
O r g a n i z e r
week, select Options > Week view. To delete all notes in the calendar,
select the month or week view, and select Options > Delete all notes.
Other options for the day view may be Make a note, Delete, Edit, Move,
or Repeat a note; Copy a note to another day; and Send note as a text
message or multimedia message, with IR, or to the calendar of another
compatible phone. In Settings you can set the date and time settings. In
Auto-delete notes you can set the phone to delete old notes
automatically after a specified time.
Make a calendar note
Select Menu > Organiser > Calendar. Scroll to the date you want, and
select Options > Make a note and one of the following note types:
Meeting,
Call,
Birthday,
Memo, or
Reminder.
Note alarm
The phone displays the note, and if set, sounds a tone. With a call note
on the display, to call the displayed number, press the call key. To
stop the alarm and to view the note, select View. To stop the alarm for
about 10 minutes, select Snooze. To stop the alarm without viewing the
note, select Exit.
■ To-do list
To save notes for tasks that you must do, select Menu > Organiser > To-
do list.
To create a note if no note is added, select Add note; otherwise, select
Options > Add. Write the note, and select Save. Select the priority, the
deadline, and the alarm type for the note.
To view a note, scroll to it, and select View.
You can also select an option to delete the selected note and delete all
the notes that you have marked as done. You can sort the notes by
priority or deadline; send a note to another phone using a text message,
multimedia message, or infrared; save a note as a calendar note; or
access the calendar. While viewing a note, you can also select an option
to edit the deadline or priority for the note or mark the note as done.
66
O r g a n i z e r
■ Notes
To use this application for writing and sending notes, select Menu >
Organiser > Notes. To create a note if no note is added, select Add note;
otherwise, select Options > Make a note. Write a note, and select Save.
Other options for notes include deleting and editing a note. While
editing a note, you can also exit the text editor without saving the
changes. You can send the note to compatible devices using a text
message, a multimedia message, or IR.
■ Synchronization
a remote Internet server (network service) or on a compatible PC. If you
have saved data on the remote Internet server, to synchronize your
phone, start the synchronization from your phone. To synchronize the
data in the phone contacts, calendar, and notes to correspond with the
data of your compatible PC, start the synchronization from the PC. The
contact data in your SIM card is not synchronized.
Answering an incoming call during synchronization ends the
synchronization, and you must restart it.
Server synchronization
Before synchronizing from your phone, you must do the following:
• Subscribe to a synchronization service. For details, contact your
service provider.
• Retrieve the synchronization settings from your service provider. See
“Synchronization settings,” p. 68.
To start the synchronization from your phone, do the following:
1. Select the configuration settings you need for the synchronization.
See “Synchronization settings,” p. 68.
2. Select Menu > Organiser > Sync > Server sync > Data to be
synchronised. Mark the data to be synchronized.
3. Select Menu > Organiser > Sync > Server sync > Synchronise. The
marked data of the active set is synchronized after confirmation.
67
O r g a n i z e r
Synchronizing for the first time or after an interrupted synchronization
may take up to 30 minutes to complete, if the contacts or calendar are
full.
Synchronization settings
You may receive the configuration settings required for synchronization
as a configuration message from the service provider. To manage the
configuration settings, see “Configuration,” p. 58.
1. Select Menu > Organiser > Sync > Server sync > Sync settings and
from the following options:
Configuration — Only the configurations that support the
synchronization are shown. Select a service provider, Default, or
Personal config. for synchronization.
Account — Select a synchronization service account contained in the
active configuration settings.
2. Select PC sync settings to enter the settings for server alerted
synchronization. Set the User name and Password.
The user name and password must be the same in the phone and in
the PC.
Synchronize from a compatible PC
To synchronize Contacts, Calendar, and Notes from a compatible PC, use
an IR or data cable connection. You also need Nokia PC Suite software
of your phone installed on the PC. Start the synchronization from the PC
using Nokia PC Suite.
■ Calculator
The calculator in your phone adds, subtracts, multiplies, divides,
calculates the square and the square root, and converts currency values.
Note: This calculator has limited accuracy and is designed for simple
calculations.
Select Menu > Organiser > Calculator. When 0 is displayed on the
screen, enter the first number in the calculation. Press # for a decimal
68
O r g a n i z e r
point. Select Options > Add, Subtract, Multiply, Divide, Square, Square
root, or Change sign. Enter the second number, if needed. For a total,
select Equals. Repeat this sequence as many times as it is necessary. To
start a new calculation, select and hold Clear.
To perform a currency conversion, select Menu > Organiser >
Calculator. To save the exchange rate, select Options > Exchange rate.
Select either of the displayed options. Enter the exchange rate, press the
# key for a decimal point, and select OK. The exchange rate remains in
the memory until you replace it with another one. To perform the
currency conversion, enter the amount to be converted, and select
Options > In domestic or In foreign.
■ Stopwatch
To measure time, take intermediate times, or take lap times, use the
stopwatch. During timing, the other functions of the phone can be used.
To set the stopwatch timing in the background, press the end key.
Using the stopwatch or allowing it to run in the background when using other
features increases the demand on battery power and reduces the battery life.
Select Menu > Organiser > Stopwatch and from the following options:
Split timing — to take intermediate times. To start the time observation,
select Start. Select Split every time that you want to take an
intermediate time. To stop the time observation, select Stop. To save the
measured time, select Save. To start the time observation again, select
Options > Start. The new time is added to the previous time. To reset the
time without saving it, select Reset. To set the stopwatch timing in the
background, press the end key.
Lap timing — to take lap times. To set the stopwatch timing in the
background, press the end key.
Continue — to view the timing that you have set in the background
Show last — to view the most recently measured time if the stopwatch is
not reset
View times or Delete times — to view or delete the saved times
69
O r g a n i z e r
■ Countdown timer
Select Menu > Organiser > Timer. Enter the alarm time in hours,
minutes, and seconds, and select OK. If you wish, write your own note
text that is displayed when the time expires. To start the countdown
timer, select Start. To change the countdown time, select Change time.
To stop the timer, select Stop timer.
If the alarm time is reached when the phone is in the standby mode, the
phone sounds a tone and flashes the note text if it is set or Countdown
time up. To stop the alarm, press any key. If no key is pressed, the alarm
automatically stops within 60 seconds. To stop the alarm and to delete
the note text, select Exit. To restart the countdown timer, select Restart.
70
A p p l i c a t i o n s
14. Applications
■ Games
Your phone software includes some games.
To launch a game, select Menu > Applications > Games. Scroll to the
desired game, and select Open.
For options related to a game, see “Other application options,” p. 71.
Game downloads
Important: Only install and use applications and other software from
sources that offer adequate security and protection against harmful
software.
Select Menu > Applications > Options > Downloads > Game
downloads. The list of available bookmarks is shown. Select More
bookmarks to access the list of bookmarks in the Web menu. See
“Bookmarks,” p. 84.
Game settings
To set sounds, lights, and shakes for games and applications, select
Menu > Applications > Options > App. settings.
■ Collection
Your phone software includes some Java applications specially designed
for this Nokia phone.
To launch an application, select Menu > Applications > Collection.
Scroll to an application, and select Open.
Other application options
Delete — to delete the application or application set from the phone
Details — to view additional information about the application
71
A p p l i c a t i o n s
Update version — to check if a new version of the application is available
for download from Web (network service)
App. access — to restrict the application from accessing the network.
Different categories are shown. Select in each category, if available, one
of the following permissions: Ask every time to set the phone to always
ask for network access, Ask first time only to set the phone to ask for
network access only on the first attempt, Always allowed to allow the
network access, or Not allowed to not allow the network access.
Web page — to provide further information or additional data for the
application from an Internet page. This feature must be supported by
the network. It is only shown if an Internet address has been provided
with the application.
Download an application
Your phone supports J2METM Java applications. Ensure that the
application is compatible with your phone before downloading it.
Important: Only install and use applications and other software from
sources that offer adequate security and protection against harmful
software.
You can download new Java applications in different ways.
Select Menu > Applications > Options > Downloads > App. downloads.
The list of available bookmarks is shown. Select More bookmarks to
access the list of bookmarks in the Web menu. Select the appropriate
bookmark to connect to the desired page. For the availability of
different services, pricing, and tariffs, contact your service provider.
Select Menu > Web > Downloads. Download an appropriate application
or game. See “Download files,” p. 85.
Use the game download function. See “Game downloads,” p. 71.
Use the Nokia Application Installer in PC Suite to download the
applications to your phone.
Your device may have some bookmarks loaded for sites not affiliated with Nokia.
Nokia does not warrant or endorse these sites. If you choose to access them, you
should take the same precautions, for security or content, as you would with any
Internet site.
72
P u s h t o t a l k
15. Push to talk
Push to talk (PTT) over cellular is a two-way radio service
available over a GSM/GPRS cellular network (network service). PTT
provides direct voice communication. To connect, press and hold the
volume up (PTT) key.
You can use PTT to have a conversation with one person or with a group
of people having compatible devices. When your call is connected, the
person or group you are calling does not have to answer the phone. The
participants should confirm the reception of any communications where
appropriate, as there is no other confirmation whether the recipients
have heard the call.
To check availability and costs, and to subscribe to the service, contact
your service provider. Roaming services may be more limited than for
normal calls.
Before you can use the PTT service, you must define the required PTT
service settings. See “PTT settings,” p. 80.
While you are connected to the PTT service, you can use the other
functions of the phone. The PTT over cellular service is not connected to
traditional voice communication, and therefore many of the services
available for traditional voice calls (for example, voice mailbox) are not
available for PTT over cellular communications.
■ Push to talk menu
Select Menu > Push to talk.
To connect to or disconnect from the PTT service, select Switch PTT on or
Switch PTT off.
To view the received callback requests, select Callback inbox.
To view the list of PTT channels, select Channel list.
To view the list of contacts to which you have added the PTT address
received from the service provider, select Contacts list.
To add a new PTT channel to the phone, select Add channel.
73
P u s h t o t a l k
To set the PTT settings for use, select PTT settings.
To set the required settings for the PTT connection, select Config.
settings.
To open the browser and to connect to the PTT network portal provided
by the service provider, select Web.
■ Connect to and disconnect PTT
To connect to the PTT service, select Menu > Push to talk > Switch PTT
on. indicates the PTT connection.
indicates that the service is
temporarily unavailable. The phone automatically tries to reconnect to
the service until you disconnect from the PTT service. If you have added
channels to the phone, you are automatically joined to the active
(Default or Listened) channels, and the name of the default channel is
displayed in the standby mode.
To disconnect from the PTT service, select Switch PTT off.
■ Make and receive a PTT call
Select Menu > Settings > Tones > Push to talk settings to set the phone
to use the loudspeaker or headset for PTT communication.
Warning: Do not hold the device near your ear when the loudspeaker is
in use, because the volume may be extremely loud.
When connected to the PTT service, you can make or receive dial-out
calls, channel calls, or one-to-one calls. One-to-one calls are calls you
make to only one person.
Make a dial-out PTT call
For a dial-out PTT call you can select multiple PTT contacts from the
contact list. The recipients get an incoming call and need to accept the
call in order to participate. A dial-out call creates a temporary channel,
and the participants join this channel only for the duration of the call.
After the call, the temporary dial-out channel is deleted.
Select Menu > Push to talk > Contacts list, and mark the desired
contacts for the dial-out call.
74
P u s h t o t a l k
The icon behind the contact in the list denotes current login status:
,
, or
unknown;
indicate that the person is available, unavailable, or
indicates that the login status is not available. The login
status is only available for subscribed contacts. To change the
subscribed contacts, select Options and from the available contact list
options Subscribe contact or Unsubscr. contact; or if one or more
contacts are already marked, Subscribe marked or Unsubscr. marked.
Press and hold the volume up (PTT) key briefly to start the dial-out call.
The marked contacts are called by the PTT service, and the joining
contacts are shown on the display. Press and hold the volume up (PTT)
key again to talk to the joined contacts. Release the volume up (PTT) key
to hear the response.
Press the end key to end the dial-out call.
Make a channel call
To make a call to the default channel, press and hold the volume up (PTT)
key. A tone sounds, indicating that the access is granted, and the phone
displays your nickname and channel name.
To make a call to a non-default channel, select Channel list in the PTT
menu, scroll to the desired channel, and press and hold the volume up
(PTT) key.
Press and hold the volume up (PTT) key the entire time you are talking,
and hold the phone in front of you so that you can see the display. When
you have finished, release the volume up (PTT) key. Talking is allowed on
a first-come, first-served basis. When someone stops talking, the first
person to press the volume up (PTT) key can talk next.
Make a one-to-one call
To start a one-to-one call from the list of contacts to which you have
added the PTT address, select Contacts list. Scroll to a contact, and press
and hold the volume up (PTT) key.
You can also select the contact from Contacts.
75
P u s h t o t a l k
To start a one-to-one call from the list of PTT channels, select Channel
list, and scroll to the desired channel. Select Options > Active members,
scroll to the desired contact, and press and hold the volume up (PTT) key.
To start a one-to-one call from the list of callback requests you have
received, select Callback inbox. Scroll to the desired nickname, and press
and hold the volume up (PTT) key.
Receive a PTT call
A short tone notifies you of an incoming channel and one-to-one call.
When receiving a channel call, the channel name and the nickname of
the caller are displayed. When receiving a one-to-one call from a person
whose information you have saved in Contacts, the saved name is
displayed if identified; otherwise, only the nickname of the caller is
displayed.
You can either accept or reject an incoming one-to-one call if you have
set the phone to first notify you of the one-to-one calls.
If you press and hold the volume up (PTT) key to try to respond to a
channel while another member is talking, you hear a queuing tone, and
Queuing is displayed as long as you press the volume up (PTT) key. Press
and hold the volume up (PTT) key, and wait for the other person to
finish; then you can talk.
■ Callback requests
If you make a one-to-one call and do not get a response, you can send a
request for the person to call you back.
When someone sends you a callback request, Callback request received
is displayed in the standby mode. When you receive a callback request
from someone who is not in your contacts list, you can save the name to
your Contacts.
76
P u s h t o t a l k
Send a callback request
You can send a callback request in the following ways:
• To send a callback request from the contacts list in the Push to talk
menu, select Contacts list. Scroll to a contact, and select Options >
Send callback.
• To send a callback request from Contacts, search for the desired
contact, select Details, scroll to the PTT address, and select
Options > Send callback.
• To send a callback request from the channel list in the PTT menu,
select Channel list, and scroll to the desired channel. Select
Options > Active members, scroll to the desired contact, and select
Options > Send callback.
• To send a callback request from the callback request list in the Push
to talk menu, select Callback inbox. Scroll to a contact, and select
Options > Send callback.
Respond to a callback request
1. To open the Callback inbox, select View. The list of nicknames of the
persons who have sent you callback requests is shown.
2. To make a one-to-one call, press and hold the volume up (PTT) key.
3. To send a call request back to the sender, select Options > Send
callback.
To delete the request, select Delete.
Save the callback request sender
1. To open the Callback inbox, select View. The list of nicknames of the
persons who have sent you callback requests is shown.
2. To view the sender's PTT address, select Options > View PTT address.
To save a new contact or to add the PTT address to a contact, select
Options > Save as or Add to contact.
77
P u s h t o t a l k
■ Add a one-to-one contact
You can save the names of persons to whom you often make one-to-one
calls in the following ways:
• To add a PTT address to a name in Contacts, search for the desired
contact, and select Options > Add detail > PTT address.
• To add a contact to the PTT contacts list, select Menu > Push to
talk > Contacts list > Options > Add contact.
• To add a contact from the channel list, connect to the PTT service,
select Channel list, and scroll to the desired channel. Select
Options > Active members. Scroll to the member whose contact
information you want to save, and select Options. To add a new
contact, select Save as. To add a PTT address to a name in Contacts,
select Add to contact.
■ Create and set up channels
When you call a channel, all members joined to the channel hear the call
simultaneously.
Each member in the channel is identified by a nickname, which is shown
as a caller identification. Channel members can choose a nickname for
themselves in each channel.
Channels are registered with a URL address. One user registers the
channel URL in the network by joining the channel session the first time.
There are three types of PTT channels:
• Provisioned channels are closed channels that allow only selected
participants provisioned by the service provider to join.
• Ad hoc channels are channels that the users can create. You can
create your own channel, and invite members to the channel.
• Ad hoc pro channels are channels you can create from members in a
provisioned channel. For example, a business can have a closed
channel and separate channels created for certain business
functions.
78
P u s h t o t a l k
Add a channel
Select Menu > Push to talk > Add channel. Select from the following
options:
Guided — to add a new channel. To set the security level for the channel,
select Public channel or Private channel. If you select Private channel,
the phone automatically creates a scrambled part to the channel
address that the members cannot view when they receive the invitation
to the channel. Only the person who creates the private channel can
invite more members to the channel. Enter the name for the channel.
Select Default, Listened, or Inactive. The phone indicates that the
channel is saved and its status. Default and Listened are active channels.
When you press and hold the volume up (PTT) key to make a channel
call, the default channel is called if you have not scrolled to any other
channel or contact. To send an invitation to the channel, select Yes
when the phone requests it. You can send the invitation using a text
message or IR.
The members you invite to the public channels can also invite more
members to the channel.
Manual — to join an existing channel. Enter the channel address. Select
Default, Listened, or Inactive. The phone indicates that the channel is
saved and its status. Default and Listened are active channels. When you
press and hold the volume up (PTT) key to make a channel call, the
default channel is called if you have not scrolled to any other channel or
contact.
Receive an invitation
1. When you receive a text message invitation to a channel, Channel
invitation received: is displayed.
2. To view the nickname of the person who sent the invitation and the
channel address if the channel is not a private channel, select View.
3. To add the channel to your phone, select Save. To set the status for
the channel, select Default, Listened, or Inactive.
To reject the invitation, select Exit > Yes, or select View > Discard > Yes.
79
P u s h t o t a l k
■ PTT settings
There are two kinds of PTT settings: settings for connecting to the
service and settings for use.
You may receive the settings for connecting to the service from your
service provider. See “Configuration settings service,” p. 10. You can
enter the settings manually. See “Configuration,” p. 58.
To select the settings for connecting to the service, select Menu > Push
to talk > Config. settings and from the following options:
Configuration — to select a service provider, Default, or Personal config.
for PTT service. Only the configurations that support the PTT service are
shown.
Account — to select a PTT service account contained in the active
configuration settings
You can also select from the following options: PTT user name, Default
nickname, PTT password, Domain, and Server address
To edit the PTT settings for use, select Menu > Push to talk > PTT
settings and from the following:
1 to 1 calls > On — to select the phone to allow the reception of
incoming one-to-one calls
1 to 1 calls > Off — to make but not receive one-to-one calls. The service
provider may offer some services that override these settings. To set the
phone to first notify you of incoming one-to-one calls with a ringing
tone, select Notify.
Listened channels > On — to activate the listened channels
PTT status in startup > Yes — to set the phone to automatically connect
to the PTT service when you switch the phone on
Send my PTT address > No — to hide your PTT address from channel and
one-to-one calls
80
W e b
16. Web
You can access various mobile Internet services with your
phone browser (network service).
Important: Use only services that you trust and that offer adequate
security and protection against harmful software.
Check the availability of these services, pricing, tariffs, and instructions
with your service provider.
With the phone browser you can view the services that use wireless
markup language (WML) or extensible hypertext markup language
(XHTML) on their pages. Appearance may vary due to screen size. You
may not be able to view all details of the Internet pages.
■ Set up browsing
You may receive the configuration settings required for browsing as a
configuration message from the service provider that offers the service
that you want to use. See “Configuration settings service,” p. 10. You
can also enter all the configuration settings manually. See
“Configuration,” p. 58.
■ Connect to a service
First, verify that the correct configuration settings of the service that
you want to use are activated.
1. To select the settings for connecting to the service, select Menu >
Web > Settings > Configuration settings.
2. Select Configuration. Only the configurations that support browsing
service are shown. Select a service provider, Default, or Personal
config. for browsing. See “Set up browsing,” p. 81.
Select Account and a browsing service account contained in the
active configuration settings.
Select Display terminal window > Yes to perform manual user
authentication for intranet connections.
81
W e b
Secondly, make a connection to the service in one of the following ways:
• Select Menu > Web > Home; or in the standby mode, press and
hold 0.
• To select a bookmark of the service, select Menu > Web >
Bookmarks.
• To select the last URL, select Menu > Web > Last web address.
• To enter the address of the service, select Menu > Web > Go to
address, enter the address of the service, and select OK.
■ Browse pages
After you make a connection to the service, you can start browsing its
pages. The function of the phone keys may vary in different services.
Follow the text guides on the phone display. For more information,
contact your service provider.
If packet data is selected as the data bearer,
is shown on the top left
of the display during browsing. If you receive a call or a text message, or
make a call during a packet data connection, is shown on the top of
the display to indicate that the packet data connection is suspended (on
hold). After a call the phone tries to reconnect the packet data
connection.
Browse with phone keys
Use the navigation keys to browse through the page.
To select a highlighted item, press the call key, or select Select.
To enter letters and numbers, press the keys, 0 to 9. To enter special
characters, press *.
Options while browsing
Nokia.com, Home, Add bookmark, Bookmarks, Page options, History,
Downloads, Other options, Reload, and Quit may be available. The
service provider may also offer other options.
A cache is a memory location that is used to store data temporarily. If you have
tried to access or have accessed confidential information requiring passwords,
82
W e b
empty the cache after each use. The information or services you have accessed is
stored in the cache.
To empty the cache, see “Cache memory,” p. 86.
Direct calling
The browser supports functions that you can access while browsing. You
can make a phone call, and save a name and a phone number from a
page.
■ Appearance settings
While browsing, select Options > Other options > Appear. settings; or in
the standby mode, select Menu > Web > Settings > Appearance
settings and from the following options:
Text wrapping > On — to set the text to continue on the next line on the
display. If you select Off, the text is abbreviated.
Font size > Extra small, Small, or Medium — to set the font size
Show images > No — to hide pictures on the page. This can speed up the
browsing of pages that contain a lot of pictures.
Alerts > Alert for unsecure connection > Yes — to set the phone to alert
when an encrypted connection changes to unencrypted during browsing
Alerts > Alert for unsecure items > Yes — to set the phone to alert when
an encrypted page contains an unsecure item. These alerts do not
guarantee a secure connection. For more information, see “Browser
security,” p. 86.
Character encoding > Content encoding — to select the encoding for the
browser page content
Character encoding > Unicode (UTF-8) web addresses > On — to set the
phone to send a URL as a UTF-8 encoding. You may need this setting
when you access a Web page created in foreign language.
Screen size > Full or Small — to set the screen size
83
W e b
■ Cookies
A cookie is data that a site saves in the cache memory of your phone.
Cookies are saved until you clear the cache memory. See “Cache
memory,” p. 86.
While browsing, select Options > Other options > Security > Cookie
settings; or in the standby mode, select Menu > Web > Settings >
Security settings > Cookies. To allow or prevent the phone from
receiving cookies, select Allow or Reject.
■ Scripts over secure connection
You can select whether to allow the running of scripts from a secure
page. The phone supports WML scripts.
1. While browsing, select Options > Other options > Security >
WMLScript sett.; or in the standby mode, select Menu > Web >
Settings > Security settings > WMLScripts over secure connection.
2. To allow the scripts, select Allow.
■ Bookmarks
You can save page addresses as bookmarks in the phone memory.
1. While browsing, select Options > Bookmarks; or in the standby
mode, select Menu > Web > Bookmarks.
2. Scroll to a bookmark, and select it; or press the call key to make a
connection to the page associated with the bookmark.
3. Select Options to view, edit, delete, or send the bookmark; create a
new bookmark; or save the bookmark to a folder.
Your device may have some bookmarks loaded for sites not affiliated with Nokia.
Nokia does not warrant or endorse these sites. If you choose to access them, you
should take the same precautions, for security or content, as you would with any
Internet site.
Receive a bookmark
When you have received a bookmark that is sent as a bookmark,
1 bookmark received is displayed. To save the bookmark, select Show >
84
W e b
Save. To view or delete the bookmark, select Options > View or Delete.
To discard the bookmark directly after you have received the bookmark,
select Exit > OK.
■ Download files
To download more tones, images, games, or applications to your phone
(network service), select Menu > Web > Downloads > Tone downloads,
Graphic downloads, Game downloads, Video downloads, Theme
downloads, or App. downloads.
Important: Only install and use applications and other software from
sources that offer adequate security and protection against harmful
software.
To save all downloaded files automatically in the appropriate folder in
Gallery or in Applications, select Menu > Web > Settings >
Downloading settings > Automatic saving > On.
■ Service inbox
The phone is able to receive service messages (pushed messages) sent by
your service provider (network service). Service messages are
notifications of, for example, news headlines, and they may contain a
text message or an address of a service.
To access the Service inbox in the standby mode, when you have
received a service message, select Show. If you select Exit, the message
is moved to the Service inbox. To access the Service inbox later, select
Menu > Web > Service inbox.
To access the Service inbox while browsing, select Options > Other
options > Service inbox. Scroll to the message you want, and to activate
the browser and download the marked content, select Retrieve. To
display detailed information on the service notification or to delete the
message, select Options > Details or Delete.
85
W e b
Service inbox settings
Select Menu > Web > Settings > Service inbox settings.
To set whether you want to receive service messages, select Service
messages > On or Off.
To set the phone to receive service messages only from content authors
approved by the service provider, select Message filter > On. To view the
list of the approved content authors, select Trusted channels.
To set the phone to automatically activate the browser from the standby
mode when the phone has received a service message, select Automatic
connection > On. If you select Off, the phone activates the browser only
after you select Retrieve when the phone has received a service
message.
■ Cache memory
A cache is a memory location that is used to store data temporarily. If you have
tried to access or have accessed confidential information requiring passwords,
empty the cache after each use. The information or services you have accessed is
stored in the cache.
To empty the cache, while browsing, select Options > Other options >
Clear the cache; in the standby mode, select Menu > Web > Clear the
cache.
■ Browser security
Security features may be required for some services, such as online
banking or shopping. For such connections you need security
certificates and possibly a security module, which may be available on
your SIM card. For more information, contact your service provider.
Security module
The security module improves security services for applications
requiring a browser connection, and allows you to use a digital
signature. The security module may contain certificates as well as
private and public keys. The certificates are saved in the security module
by the service provider.
86
W e b
Select Menu > Web > Settings > Security settings > Security module
settings and from the following options:
Security module details — to show the security module title, status,
manufacturer, and serial number
Module PIN request — to set the phone to ask for the module PIN when
using services provided by the security module. Enter the code, and
select On. To disable the module PIN request, select Off.
Change module PIN — to change the module PIN, if allowed by the
security module. Enter the current module PIN code, then enter the new
code twice.
Change signing PIN — to change the signing PIN code for the digital
signature. Select the signing PIN you want to change. Enter the current
PIN code, then enter the new code twice.
See also “Access codes,” p. 9.
Certificates
Important: Even if the use of certificates makes the risks involved in
remote connections and software installation considerably smaller,
they must be used correctly in order to benefit from increased security.
The existence of a certificate does not offer any protection by itself; the
certificate manager must contain correct, authentic, or trusted
certificates for increased security to be available. Certificates have a
restricted lifetime. If Expired certificate or Certificate not valid yet is
shown even if the certificate should be valid, check that the current
date and time in your device are correct.
Before changing any certificate settings, you must make sure that you
really trust the owner of the certificate and that the certificate really
belongs to the listed owner.
There are three kinds of certificates: server certificates, authority
certificates, and user certificates. You may receive these certificates
from your service provider. Authority certificates and user certificates
may also be saved in the security module by the service provider.
To view the list of the authority or user certificates downloaded into
your phone, select Menu > Web > Settings > Security settings > User
certificates or Authority certificates.
87
W e b
The security indicator
is displayed during a connection, if the data
transmission between the phone and the content server is encrypted.
The security icon does not indicate that the data transmission between the
gateway and the content server (or place where the requested resource is stored)
is secure. The service provider secures the data transmission between the
gateway and the content server.
Digital signature
You can make digital signatures with your phone if your SIM card has a
security module. Using the digital signature can be the same as signing
your name to a paper bill, contract, or other document.
To make a digital signature, select a link on a page, for example, the title
of the book you want to buy and its price. The text to sign, which may
include the amount and date, is shown.
Check that the header text is Read and that the digital signature icon
is shown.
If the digital signature icon does not appear, there is a security breach,
and you should not enter any personal data such as your signing PIN.
To sign the text, read all of the text first, and select Sign.
The text may not fit within a single screen. Therefore, make sure to scroll
through and read all of the text before signing.
Select the user certificate you want to use. Enter the signing PIN (see
“Access codes,” p. 9), and select OK. The digital signature icon
disappears, and the service may display a confirmation of your purchase.
■ Positioning information
The network may send you a location request. You can ensure that the
network delivers location information of your phone only if you approve
it (network service). Contact your network operator or service provider
to subscribe and to agree upon the delivery of location information.
To accept or reject the location request, select Accept or Reject. If you
miss the request, the phone automatically accepts or rejects it
according to what you have agreed with your network operator or
88
W e b
service provider. The phone displays 1 missed position request. To view
the missed location request, select Show.
To view the information on the 10 most recent privacy notifications and
requests or to delete them, select Menu > Web > Positioning > Position
log > Open folder or Delete all.
89
S I M s e r v i c e s
17. SIM services
Your SIM card may provide additional services that you can access. This
menu is shown only if it is supported by your SIM card. The name and
contents of the menu depend on the SIM card.
For availability and information on using SIM card services, contact your SIM
card vendor. This may be the service provider, network operator, or other vendor.
To set the phone to show you the confirmation messages sent between
your phone and the network when you are using the SIM services, select
Menu > Settings > Phone > Confirm SIM service actions > Yes.
Accessing these services may involve sending messages or making a
phone call for which you may be charged.
90
P C c o n n e c t i v i t y
18. PC connectivity
You can send and receive e-mail, and access the Internet when your
phone is connected to a compatible PC through an infrared or a data
cable (CA-42) connection. You can use your phone with a variety of PC
connectivity and data communications applications.
■ Nokia PC Suite
With Nokia PC Suite you can synchronize Contacts, Calendar, To-do list,
and Notes between your phone and the compatible PC.
You may find more information about Nokia PC Suite, for example
downloadable files, in the support area on the Nokia Web site at
www.nokia.com/support.
■ Packet data, HSCSD, and CSD
With your phone you can use packet data, high-speed circuit switched
data (HSCSD), and circuit switched data (CSD, GSM data).
For availability and subscription to data services, contact your network
operator or service provider.
The use of HSCSD services consumes the phone battery faster than
normal voice or data calls. You may need to connect the phone to a
charger for the duration of data transfer.
See “Packet data (EGPRS),” p. 56.
■ Data communication applications
For information on using a data communication application, refer to the
documentation provided with it. Making or answering phone calls
during a computer connection is not recommended, as it might disrupt
the operation. For better performance during data calls, place the phone
on a stationary surface with the keypad facing down. Do not move the
phone by holding it in your hand during a data call.
91
B a t t e r y i n f o r m a t i o n
19. Battery information
■ Charging and discharging
Your device is powered by a rechargeable battery. The full performance of a new
battery is achieved only after two or three complete charge and discharge cycles.
The battery can be charged and discharged hundreds of times but it will
eventually wear out. When the talk and standby times are noticeably shorter
than normal, replace the battery. Use only Nokia approved batteries, and
recharge your battery only with Nokia approved chargers designated for this
device.
Unplug the charger from the electrical plug and the device when not in use. Do
not leave a fully charged battery connected to a charger, since overcharging may
shorten its lifetime. If left unused, a fully charged battery will lose its charge over
time.
Use the battery only for its intended purpose. Never use any charger or battery
that is damaged.
Do not short-circuit the battery. Accidental short-circuiting can occur when a
metallic object such as a coin, clip, or pen causes direct connection of the
positive (+) and negative (-) terminals of the battery. (These look like metal strips
on the battery.) This might happen, for example, when you carry a spare battery
in your pocket or purse. Short-circuiting the terminals may damage the battery
or the connecting object.
Leaving the battery in hot or cold places, such as in a closed car in summer or
winter conditions, will reduce the capacity and lifetime of the battery and its
ability to charge. Always try to keep the battery between 15°C and 25°C (59°F
and 77°F). A device with a hot or cold battery may not work temporarily, even
when the battery is fully charged. Battery performance is particularly limited in
temperatures well below freezing.
Do not dispose of batteries in a fire as they may explode. Batteries may also
explode if damaged. Dispose of batteries according to local regulations. Please
recycle when possible. Do not dispose as household waste.
■ Nokia battery authentication guidelines
Always use original Nokia batteries for your safety. To check that you are getting
an original Nokia battery, purchase it from an authorized Nokia dealer, look for
92
B a t t e r y i n f o r m a t i o n
the Nokia Original Enhancements logo on the packaging, and inspect the
hologram label using the following steps:
Successful completion of the four steps is not a total assurance of the
authenticity of the battery. If you have any reason to believe that your battery is
not an authentic original Nokia battery, you should refrain from using it and take
it to the nearest authorized Nokia service point or dealer for assistance. Your
authorized Nokia service point or dealer will inspect the battery for authenticity.
If authenticity cannot be verified, return the battery to the place of purchase.
Authenticate hologram
1. When looking at the hologram label, you should see
the Nokia connecting hands symbol from one angle
and the Nokia Original Enhancements logo when
looking from another angle.
2. When you angle the hologram left, right, down, and
up, you should see 1, 2, 3, and 4 dots on each side
respectively.
3. Scratch the side of the label to reveal a 20-digit code,
for example, 12345678919876543210. Turn the
battery so that the numbers are facing upwards. The
20-digit code reads starting from the number at the
top row followed by the bottom row.
4. Confirm that the 20-digit code is valid by following
the instructions at www.nokia.com/batterycheck.
To create a text message, enter the 20-digit code, for
example, 12345678919876543210, and send to +44
7786 200276.
National and international operator charges will
apply.
You should receive a message indicating whether the code can be
authenticated.
93
B a t t e r y i n f o r m a t i o n
What if your battery is not authentic?
If you cannot confirm that your Nokia battery with the hologram on the label is
an authentic Nokia battery, please do not use the battery. Take it to the nearest
authorized Nokia service point or dealer for assistance. The use of a battery that
is not approved by the manufacturer may be dangerous and may result in poor
performance and damage to your device and its enhancements. It may also
invalidate any approval or warranty applying to the device.
To find out more about original Nokia batteries, visit www.nokia.com/battery.
94
C a r e a n d m a i n t e n a n c e
Care and maintenance
Your device is a product of superior design and craftsmanship and should be
treated with care. The suggestions below will help you protect your warranty
coverage.
•
Keep the device dry. Precipitation, humidity, and all types of liquids or
moisture can contain minerals that will corrode electronic circuits. If your
device does get wet, remove the battery, and allow the device to dry
completely before replacing it.
•
•
•
Do not use or store the device in dusty, dirty areas. Its moving parts and
electronic components can be damaged.
Do not store the device in hot areas. High temperatures can shorten the life of
electronic devices, damage batteries, and warp or melt certain plastics.
Do not store the device in cold areas. When the device returns to its normal
temperature, moisture can form inside the device and damage electronic
circuit boards.
•
•
Do not attempt to open the device other than as instructed in this guide.
Do not drop, knock, or shake the device. Rough handling can break internal
circuit boards and fine mechanics.
•
•
•
•
Do not use harsh chemicals, cleaning solvents, or strong detergents to clean
the device.
Do not paint the device. Paint can clog the moving parts and prevent proper
operation.
Use a soft, clean, dry cloth to clean any lenses (such as camera, proximity
sensor, and light sensor lenses).
Use only the supplied or an approved replacement antenna. Unauthorized
antennas, modifications, or attachments could damage the device and may
violate regulations governing radio devices.
•
•
Use chargers indoors.
Always create a backup of data you want to keep (such as contacts and
calendar notes) before sending your device to a service facility.
All of the above suggestions apply equally to your device, battery, charger, or any
enhancement. If any device is not working properly, take it to the nearest
authorized service facility for service.
95
A d d i t i o n a l s a f e t y i n f o r m a t i o n
Additional safety information
Your device and its enhancements may contain small parts. Keep them out of the
reach of small children.
■ Operating environment
Remember to follow any special regulations in force in any area and always
switch off your device when its use is prohibited or when it may cause
interference or danger. Use the device only in its normal operating positions. This
device meets RF exposure guidelines when used either in the normal use position
against the ear or when positioned at least 2.2 centimeters (0.84 inches) away
from the body. When a carry case, belt clip, or holder is used for body-worn
operation, it should not contain metal and should position the device the above-
stated distance from your body.
To transmit data files or messages, this device requires a quality connection to
the network. In some cases, transmission of data files or messages may be
delayed until such a connection is available. Ensure the above separation
distance instructions are followed until the transmission is completed.
Parts of the device are magnetic. Metallic materials may be attracted to the
device. Do not place credit cards or other magnetic storage media near the
device, because information stored on them may be erased.
■ Medical devices
Operation of any radio transmitting equipment, including wireless phones, may
interfere with the functionality of inadequately protected medical devices.
Consult a physician or the manufacturer of the medical device to determine if
they are adequately shielded from external RF energy or if you have any
questions. Switch off your device in health care facilities when any regulations
posted in these areas instruct you to do so. Hospitals or health care facilities may
be using equipment that could be sensitive to external RF energy.
Pacemakers
Pacemaker manufacturers recommend that a minimum separation of
15.3 centimeters (6 inches) be maintained between a wireless phone and a
pacemaker to avoid potential interference with the pacemaker. These
recommendations are consistent with the independent research by and
recommendations of Wireless Technology Research. Persons with pacemakers
should do the following:
96
A d d i t i o n a l s a f e t y i n f o r m a t i o n
•
Always keep the device more than 15.3 centimeters (6 inches) from the
pacemaker
•
•
Not carry the device in a breast pocket
Hold the device to the ear opposite the pacemaker to minimize the potential
for interference.
If you suspect interference, switch off your device, and move the device away.
Hearing aids
Some digital wireless devices may interfere with some hearing aids. If
interference occurs, consult your service provider.
■ Vehicles
RF signals may affect improperly installed or inadequately shielded electronic
systems in motor vehicles such as electronic fuel injection systems, electronic
antiskid (antilock) braking systems, electronic speed control systems, and air bag
systems. For more information, check with the manufacturer, or its
representative, of your vehicle or any equipment that has been added.
Only qualified personnel should service the device, or install the device in a
vehicle. Faulty installation or service may be dangerous and may invalidate any
warranty that may apply to the device. Check regularly that all wireless device
equipment in your vehicle is mounted and operating properly. Do not store or
carry flammable liquids, gases, or explosive materials in the same compartment
as the device, its parts, or enhancements. For vehicles equipped with an air bag,
remember that air bags inflate with great force. Do not place objects, including
installed or portable wireless equipment in the area over the air bag or in the air
bag deployment area. If in-vehicle wireless equipment is improperly installed,
and the air bag inflates, serious injury could result.
Using your device while flying in aircraft is prohibited. Switch off your device
before boarding an aircraft. The use of wireless teledevices in an aircraft may be
dangerous to the operation of the aircraft, disrupt the wireless telephone
network, and may be illegal.
■ Potentially explosive environments
Switch off your device when in any area with a potentially explosive atmosphere,
and obey all signs and instructions. Potentially explosive atmospheres include
areas where you would normally be advised to turn off your vehicle engine.
Sparks in such areas could cause an explosion or fire resulting in bodily injury or
even death. Switch off the device at refueling points such as near gas pumps at
service stations. Observe restrictions on the use of radio equipment in fuel
97
A d d i t i o n a l s a f e t y i n f o r m a t i o n
depots, storage, and distribution areas; chemical plants; or where blasting
operations are in progress. Areas with a potentially explosive atmosphere are
often, but not always, clearly marked. They include below deck on boats,
chemical transfer or storage facilities, vehicles using liquefied petroleum gas
(such as propane or butane), and areas where the air contains chemicals or
particles such as grain, dust, or metal powders.
■ Emergency calls
Important: Wireless phones, including this device, operate using radio
signals, wireless networks, landline networks, and user-programmed
functions. Because of this, connections in all conditions cannot be
guaranteed. You should never rely solely on any wireless device for
essential communications like medical emergencies.
To make an emergency call:
1. If the device is not on, switch it on. Check for adequate signal strength.
Some networks may require that a valid SIM card is properly inserted in the
device.
2. Press the end key as many times as needed to clear the display and ready the
device for calls.
3. Enter the official emergency number for your present location. Emergency
numbers vary by location.
4. Press the call key.
If certain features are in use, you may first need to turn those features off before
you can make an emergency call. Consult this guide or your service provider for
more information.
When making an emergency call, give all the necessary information as accurately
as possible. Your wireless device may be the only means of communication at the
scene of an accident. Do not end the call until given permission to do so.
■ Certification information (SAR)
This mobile device meets guidelines for exposure to radio waves
Your mobile device is a radio transmitter and receiver. It is designed not to
exceed the limits for exposure to radio waves recommended by international
guidelines. These guidelines were developed by the independent scientific
organization ICNIRP and include safety margins designed to assure the
protection of all persons, regardless of age and health.
98
A d d i t i o n a l s a f e t y i n f o r m a t i o n
The exposure guidelines for mobile devices employ a unit of measurement known
as the Specific Absorption Rate or SAR. The SAR limit stated in the ICNIRP
guidelines is 2.0 watts/kilogram (W/kg) averaged over 10 grams of tissue. Tests
for SAR are conducted using standard operating positions with the device
transmitting at its highest certified power level in all tested frequency bands. The
actual SAR level of an operating device can be below the maximum value
because the device is designed to use only the power required to reach the
network. That amount changes depending on a number of factors such as how
close you are to a network base station. The highest SAR value under the ICNIRP
guidelines for use of the device at the ear is 0.84 W/kg.
Use of device accessories and enhancements may result in different SAR values.
SAR values may vary depending on national reporting and testing requirements
and the network band. Additional SAR information may be provided under
product information at www.nokia.com.
99
I n d e x
Index
reject . . . . . . . . . . . . . . . . . . . . 20
A
access codes . . . . . . . . . . . . . . . . . . 9
accessories. See enhancements. . . 8
alarm clock . . . . . . . . . . . . . . . . . . 65
antenna . . . . . . . . . . . . . . . . . . . . 14
application download . . . . . . . . . 11
audio messaging . . . . . . . . . . . . . 31
camera
record a video clip . . . . . . . . .62
clock settings . . . . . . . . . . . . . . . .53
codes
PUK . . . . . . . . . . . . . . . . . . . . .10
configuration . . . . . . . . . . . . . . . . 58
configuration setting service . . . 10
contact information . . . . . . . . . . . 11
contacts
business cards . . . . . . . . . . . . 45
caller groups . . . . . . . . . . . . . .47
copy . . . . . . . . . . . . . . . . . . . . .44
delete . . . . . . . . . . . . . . . . . . . 44
edit details . . . . . . . . . . . . . . .44
my numbers . . . . . . . . . . . . . . 49
my presence . . . . . . . . . . . . . .45
save . . . . . . . . . . . . . . . . . . . . .43
search . . . . . . . . . . . . . . . . . . . 43
service numbers . . . . . . . . . . . 49
settings . . . . . . . . . . . . . . . . . . 47
speed dialing . . . . . . . . . .47, 49
subscribed names . . . . . . . . . . 46
cookies . . . . . . . . . . . . . . . . . . . . . 84
countdown timer . . . . . . . . . . . . . 70
counters . . . . . . . . . . . . . . . . . . . .50
CSD . . . . . . . . . . . . . . . . . . . . . . . .91
customer service . . . . . . . . . . . . .11
B
barring password . . . . . . . . . . . . . 10
battery
authentication . . . . . . . . . . . . 92
charge level . . . . . . . . . . . . . . 17
charging . . . . . . . . . . . . . .13, 92
installation . . . . . . . . . . . . . . . 12
bookmarks . . . . . . . . . . . . . . . . . . 84
browser
appearance settings . . . . . . . 83
bookmarks . . . . . . . . . . . . . . . 84
browsing pages . . . . . . . . . . . 82
cache memory . . . . . . . . . . . . 86
certificates . . . . . . . . . . . . . . . 87
cookies . . . . . . . . . . . . . . . . . . 84
digital signature . . . . . . . . . . . 88
script settings . . . . . . . . . . . . 84
security module . . . . . . . . . . . 86
set up . . . . . . . . . . . . . . . . . . . 81
business cards . . . . . . . . . . . . . . . 45
C
cache memory . . . . . . . . . . . . . . . 86
calculator . . . . . . . . . . . . . . . . . . . 68
calendar . . . . . . . . . . . . . . . . . . . . 65
calendar note . . . . . . . . . . . . . . . . 66
call functions . . . . . . . . . . . . . . . . 20
call key . . . . . . . . . . . . . . . . . . . . . 16
call register . . . . . . . . . . . . . . . . . . 50
call settings . . . . . . . . . . . . . . . . . 54
call waiting . . . . . . . . . . . . . . . . . . 21
caller groups . . . . . . . . . . . . . . . . . 47
calls
answer . . . . . . . . . . . . . . . . . . 20
international . . . . . . . . . . . . . 20
100
D
I
data communication . . . . . . . . . .91
date settings . . . . . . . . . . . . . . . . .53
delete
indicators . . . . . . . . . . . . . . . . . . . 18
info messages . . . . . . . . . . . . . . . 39
infrared
e-mail . . . . . . . . . . . . . . . . . . .39
messages . . . . . . . . . . . . . . . . .39
dialed numbers . . . . . . . . . . . . . . .50
dictionary . . . . . . . . . . . . . . . . . . .22
digital signature . . . . . . . . . . . . . .88
display settings . . . . . . . . . . . . . . .52
downloads
installation
instant messaging
accept invitation . . . . . . . . . . 34
contacts . . . . . . . . . . . . . . . . . 36
conversation . . . . . . . . . . . . . 35
read . . . . . . . . . . . . . . . . . . . . 35
reject invitation . . . . . . . . . . . 34
service . . . . . . . . . . . . . . . . . . 33
IR. See infrared.
applications . . . . . . . . . . . 11, 85
content . . . . . . . . . . . . . . . . . .11
files . . . . . . . . . . . . . . . . . . . . .85
E
earpiece . . . . . . . . . . . . . . . . . . . . .16
EGPRS . . . . . . . . . . . . . . . . . . . . . .56
e-mail . . . . . . . . . . . . . . . . . . . . . .37
e-mail settings . . . . . . . . . . . . . . .41
emergency calls . . . . . . . . . . . . . .98
end call . . . . . . . . . . . . . . . . . . . . .20
end key . . . . . . . . . . . . . . . . . . . . .16
enhancement settings . . . . . . . . .57
enhancements . . . . . . . . . . . . . . . . .8
K
F
keyguard . . . . . . . . . . . . . . . . . . . 19
keypad lock . . . . . . . . . . . . . . . . . 19
keys . . . . . . . . . . . . . . . . . . . . . . . 16
factory settings . . . . . . . . . . . . . . .59
flash messages . . . . . . . . . . . . . . .31
folders
inbox . . . . . . . . . . . . . . . . 30, 38
other . . . . . . . . . . . . . . . . . . . .38
outbox . . . . . . . . . . . . . . . . . . .30
saved items . . . . . . . . . . . . . . .30
sent items . . . . . . . . . . . . . . . .30
font size . . . . . . . . . . . . . . . . . . . . .42
L
language . . . . . . . . . . . . . . . . 22, 23
lights . . . . . . . . . . . . . . . . . . . 52, 57
location information . . . . . . . . . . 88
lock the keypad . . . . . . . . . . . . . . 19
log . . . . . . . . . . . . . . . . . . . . . . . . 50
loudspeaker . . . . . . . . . . . . . . 16, 21
G
gallery . . . . . . . . . . . . . . . . . . . . . .61
M
maintenance . . . . . . . . . . . . . 11, 95
media
H
handsfree. See loudspeaker.
camera . . . . . . . . . . . . . . . . . . 62
radio . . . . . . . . . . . . . . . . . . . . 62
recorder . . . . . . . . . . . . . . . . . 64
memory
help text . . . . . . . . . . . . . . . . . . . .55
high-speed circuit switched data 91
HSCSD . . . . . . . . . . . . . . . . . . . . . .91
cache . . . . . . . . . . . . . . . . 83, 86
101
I n d e x
capacity . . . . . . . . . . . . . . . . . 61
phone lock. See keypad lock.
copy . . . . . . . . . . . . . . . . . . . . 44
full . . . . . . . . . . . . . . . . . . .26, 29
select . . . . . . . . . . . . . . . . . . . 47
shared . . . . . . . . . . . . . . . . . . . . 8
SIM . . . . . . . . . . . . . . . . . . . . . 43
status . . . . . . . . . . . . . . . .47, 54
menu . . . . . . . . . . . . . . . . . . . . . . . 24
message center number . . . . . . . 25
message counter . . . . . . . . . . . . . 42
message length indicator . . . . . . 26
message settings . . . . . . . . . . . . . 40
missed calls . . . . . . . . . . . . . . . . . 50
MMS. See multimedia messages.
modem settings . . . . . . . . . . . . . . 57
multimedia messages . . . . . . . . . 27
settings . . . . . . . . . . . . . . . . . . 40
my numbers . . . . . . . . . . . . . . . . . 49
my presence . . . . . . . . . . . . . . . . . 45
my shortcuts . . . . . . . . . . . . . . . . 52
phone strap . . . . . . . . . . . . . . . . . . 15
positioning . . . . . . . . . . . . . . . . . . 88
power saving . . . . . . . . . . . . . . . . 18
predictive text input . . . . . . . . . . 22
call . . . . . . . . . . . . . . . . . . . . . . 74
channel call . . . . . . . . . . . . . . 75
connect . . . . . . . . . . . . . . . . . . 74
disconnect . . . . . . . . . . . . . . .74
key . . . . . . . . . . . . . . . . . . . . . . 16
one-to-one call . . . . . . . . . . . 75
receive a call . . . . . . . . . . . . .76
settings . . . . . . . . . . . . . . . . . . 80
setup a channel . . . . . . . . . . . 78
PUK codes . . . . . . . . . . . . . . . . . . . 10
punctuation marks . . . . . . . . . . . .23
push to talk key . . . . . . . . . . . . . . 16
push to talk. See PTT.
N
names. See contacts.
navigation . . . . . . . . . . . . . . . . . . 24
navigation key . . . . . . . . . . . . . . . 16
network
EGSM . . . . . . . . . . . . . . . . . . . . 7
GSM . . . . . . . . . . . . . . . . . . . . . 7
name on display . . . . . . . . . . . 17
services . . . . . . . . . . . . . . . . . . . 7
Nokia contact and support . . . . . 11
note alarm . . . . . . . . . . . . . . . . . . 66
notes . . . . . . . . . . . . . . . . . . . . . . . 67
O
R
operator menu . . . . . . . . . . . . . . . 60
organizer . . . . . . . . . . . . . . . . . . . . 65
overview
radio . . . . . . . . . . . . . . . . . . . . . . . 62
received calls . . . . . . . . . . . . . . . . 50
recent calls list . . . . . . . . . . . . . . . 50
recorder . . . . . . . . . . . . . . . . . . . . .64
repair service . . . . . . . . . . . . . . . . 11
ringing tones . . . . . . 47, 51, 61, 62
functions . . . . . . . . . . . . . . . . . 9
keys and parts . . . . . . . . . . . . 16
P
packet data . . . . . . . . . . . . . . .56, 91
parts . . . . . . . . . . . . . . . . . . . . . . . 16
PC
S
safety
connectivity . . . . . . . . . . . . . . 91
synchronization . . . . . . . . . . . 68
PC Suite . . . . . . . . . . . . . . . . . . . . 91
additional information . . . . . 96
certification information (SAR) 98
102
emergency calls . . . . . . . . . . .98
enhancements . . . . . . . . . . . . . .8
guidelines . . . . . . . . . . . . . . . . .6
operating environment . . . . . .96
SAR . . . . . . . . . . . . . . . . . . . . .98
SAR . . . . . . . . . . . . . . . . . . . . . . . .98
screen saver . . . . . . . . . . . . . . . . . .18
script settings . . . . . . . . . . . . . . . .84
scroll key. See navigation key.
security
codes . . . . . . . . . . . . . . . . . . . . .9
module . . . . . . . . . . . . . . . . . . .86
settings . . . . . . . . . . . . . . . . . .59
selection keys . . . . . . . . . . . . 16, 17
server synchronization . . . . . . . . .67
service
speaker phone. See loudspeaker.
subscribed names
commands . . . . . . . . . . . . . . . .39
numbers . . . . . . . . . . . . . . . . . .49
services . . . . . . . . . . . . . . . . . . . . .81
settings . . . . . . . . . . . . . . . . . . . . .51
call . . . . . . . . . . . . . . . . . . . . . .54
clock . . . . . . . . . . . . . . . . . . . .53
configuration . . . . . . . . . . . . .58
connectivity . . . . . . . . . . . . . .55
date . . . . . . . . . . . . . . . . . . . . .53
display . . . . . . . . . . . . . . . . . . .52
EGPRS . . . . . . . . . . . . . . . . . . .56
enhancements . . . . . . . . . . . . .57
IR . . . . . . . . . . . . . . . . . . . . . . .55
messages . . . . . . . . . . . . . . . . .40
modem . . . . . . . . . . . . . . . . . . .57
my shortcuts . . . . . . . . . . . . . .52
packet data . . . . . . . . . . . . . . .56
phone . . . . . . . . . . . . . . . . . . . .54
profiles . . . . . . . . . . . . . . . . . . .51
restore factory settings . . . . .59
service inbox . . . . . . . . . . . . . .85
shortcuts . . . . . . . . . . . . . . . . .52
themes . . . . . . . . . . . . . . . . . . .51
time . . . . . . . . . . . . . . . . . . . . .53
tones . . . . . . . . . . . . . . . . . . . .51
shared memory . . . . . . . . . . . . . . . .8
shortcuts . . . . . . . . . . . . . . . . 17, 52
in standby mode . . . . . . . . . . .17
navigation key . . . . . . . . . . . . .17
personal list . . . . . . . . . . . . . . .17
signal strength . . . . . . . . . . . . . . .17
SIM card installation . . . . . . . . . .12
SIM services . . . . . . . . . . . . . . . . .90
SMS . . . . . . . . . . . . . . . . . . . . . . . .25
T
to-do list . . . . . . . . . . . . . . . . . . . 66
tones . . . . . . . . . . . . . . . . . . . . . . 51
traditional text input . . . . . . 22, 23
U
unlock keypad . . . . . . . . . . . . . . . 19
UPIN . . . . . . . . . . . . . . . . . . 9, 10, 59
UPIN code . . . . . . . . . . . . . . . . . . 14
V
vibrating alert . . . . . . . . . . . . . . . 51
video clip . . . . . . . . . . . . . . . . . . . 62
voice command key . . . . . . . . . . 16
voice commands . . . . . . . . . . . . . 48
voice dialing
add voice tags . . . . . . . . . . . . 48
make a call . . . . . . . . . . . . . . 49
manage voice tags . . . . . . . . 48
voice messages . . . . . . . . . . . . . . 39
voice tags . . . . . . . . . . . . . . . . . . . 48
volume keys . . . . . . . . . . . . . . . . . 16
103
I n d e x
W
X
wallpaper . . . . . . . . . . . . . . . .51, 52
Web
XHTML . . . . . . . . . . . . . . . . . . . . . . 81
bookmarks . . . . . . . . . . . . . . . 84
connect . . . . . . . . . . . . . . . . . . 81
wireless markup language . . . . . . 81
WML . . . . . . . . . . . . . . . . . . . . . . . 81
write text message . . . . . . . . . . . 26
writing language . . . . . . . . . . . . . 22
writing text . . . . . . . . . . . . . . . . . 22
104
|