Morphy Richards 47062 User Manual

47060 rev2 25/6/07 12:37 Page 1  
10/12 cup filter coffee maker  
Please read and keep these instructions  
Models Covered  
47060- Manual Interface  
47061- Digital Interface  
47062- Manual Interface & Thermal carafe  
47063- Digital Interface & Thermal carafe  
Getting the best from your new coffee maker...  
Warning: Hot water and steam  
Safety first  
Caution must be used when handling hot water,  
coffee or steam.  
Run water through your machine before first use  
It is important to run water through your coffee maker  
in order to rinse the machine. You can also run water  
through to warm your coffee machine.  
Descale as appropriate for the hardness  
of the water in your area  
It is important to descale as the performance of your  
coffee maker may be impaired by limescale and other  
impurities in the water supply.  
CM47060 Rev2  
For replacement parts, help with using your Morphy Richards product,  
problems and lots more, contact us by phone or through our website.  
UK Helpline: 0870 060 2610  
Replacement parts: 0870 167 6641  
Ireland 1800 409119  
47060 rev2 25/6/07 12:37 Page 3  
Personal safety  
Treating scalds  
Ensure the lid of the glass  
jug is securely in place  
before pouring.  
Run cold water over the  
affected area immediately.  
Do not stop to remove  
clothing, get medical help  
quickly.  
Take care to pour hot  
coffee slowly and carefully  
without tipping the glass  
jug too fast.  
Choice of coffee  
Choose a finely ground  
espresso coffee to use with  
this machine.  
Do not fill above the  
capacity mark of the water  
level gauge marked on the  
jug.  
NOTE: Avoid blends that  
are very powdery. When  
the coffee is too finely  
ground it may block the  
filter.  
Do not use the glass jug in  
a microwave.  
Milk should not be  
reheated, only heat it when  
required.  
ELECTRICAL  
When heating milk, please  
use the stainless steel jug  
provided.  
REQUIREMENTS  
Check that the voltage on  
the rating plate of your  
appliance corresponds  
with your house electricity  
supply which must be A.C.  
(Alternating Current).  
Do not fill the milk jug  
above the MAX mark.  
Do not touch metal parts  
until the unit has cooled.  
If the socket outlets in your  
home are not suitable for  
the plug supplied with this  
appliance the plug should  
be removed and the  
This appliance is not  
intended for use by  
persons (including children)  
with reduced physical,  
sensory or mental  
appropriate one fitted.  
capabilities, or lack of  
experience and knowledge,  
unless they have been  
given supervision or  
instruction concerning use  
of the appliance by a  
person responsible for their  
safety.  
WARNING: The plug  
removed from the  
mains lead, if severed,  
must be destroyed as a  
plug with a bared  
flexible cord is  
hazardous if engaged  
into a live socket  
outlet.  
Children  
Should the fuse in the 13  
amp plug require changing,  
a 13 amp BS1362 fuse  
must be fitted.  
Children do not understand  
the dangers associated  
with operating electrical  
appliances. Never allow  
children to use this  
WARNING: This  
appliance must be  
earthed.  
appliance.  
Children should be  
supervised to ensure that  
they do not play with the  
appliance.  
3
2
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119  
47060 rev2 25/6/07 12:37 Page 4  
Product features  
Á
¤
Ë
Â
È
Í
Í
/„  
/·  
Ê
Î
· 8/10 cups steel thermal  
Ë Plug storage  
È Anti drip  
Features  
coffee jug  
Measuring spoon storage  
area  
Manual interface (see  
overleaf)  
Í Lid release  
Î Hot plates  
¤ Water re-fill point  
Digital interface (see  
Measuring spoon  
overleaf)  
Filter holder and  
Frother control  
permanent mesh filter  
 Milk hot plate switch  
Lid opening push button  
Ê Illuminated water level  
Milk frother steel jug  
indicator  
12/15 cups glass coffee  
Á Coffee strength control  
jug  
3
4
47060 rev2 25/6/07 12:37 Page 5  
Ì
Ó
Ï
Ô
ÚÒ  
Manual interface version  
Auto keep warm indicator  
Ò Milk frother device ON indicator  
Ú Milk hot plate ON indicator  
Ï Function selector  
Ì
1
/2 carafe indicator  
Ó 1 carafe indicator  
Ô Brewing ON indicator  
Û
ı
Ù
˘
35  
36  
˜
Ú
Ò
ˆ
¯
34  
Digital interface version  
Auto keep warm indicator  
Ò Milk frother device ON indicator  
Ú Milk hot plate ON indicator  
ˆ Hour function push button  
˜ Minute function push button  
¯ Cup selector push button  
˘ Quality and brew indicator  
Programming mode indicator  
Û Power ON/OFF selection push  
button  
34  
Automatic timer function  
indicator  
Ù Programme selection push  
button  
Cup selection indicator  
24 hour clock  
35  
36  
ı Auto function push button  
Milk hot plate ON pilot light  
Milk frother device ON pilot light  
Milk frother device off pilot light  
Auto keep warm light  
1
/2 carafe light  
Power ON/OFF  
1 carafe light auto  
4
5
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119  
47060 rev2 25/6/07 12:37 Page 6  
A
OPERATING THE  
APPLIANCE  
MANUAL INTERFACE  
VERSIONS  
BEFORE USE  
Making coffee  
Before using your coffee maker  
for the first time or if you have  
not used it for some time, rinse  
the machine by running water  
through. Follow the procedure  
for making coffee, without coffee  
in the filter holder.  
1
2
Press the push button to  
open the hinged lid. The lid will  
automatically rise.  
Using a jug, fill the water  
reservoir ¤ with the required  
amount of water using the level  
indicator Ê as a guide. Both the  
jug and water level indicator are  
marked in cups A.  
B
The product that you have  
purchased is available in four  
different versions:  
3
Spoon the required amount  
of ground filter coffee into the  
mesh filter spreading evenly.  
We suggest one level measuring  
spoon for every cup. Ensure the  
filter is sitting properly in the  
filter holder B.  
Manual version - Glass carafe  
Manual version -Thermal carafe  
24 hour automatic timer version  
- Glass carafe  
24 hour automatic timer version  
-Thermal carafe  
4
5
Close the lid. Ensure the lid is  
closed and latched properly C,  
otherwise the machine will not  
function correctly.  
C
For the complete understanding  
of how to use your machine  
please refer to the specific  
Slide the jug ‡/· into the  
coffee maker ensuring it sits  
correctly on the hot plate D.  
The jug lid must be in place  
during the brewing process;  
otherwise the non drip valve will  
not open, causing the filter to  
flood.  
section related to your version.  
Please note not all variants are  
available in all countries, please  
contact your retailer for more  
information.  
D
5
6
47060 rev2 25/6/07 12:37 Page 7  
E
Thermal Carafe Variant  
We suggest consuming your  
coffee within two hours, after  
this time we suggest brewing  
another jug of fresh coffee.  
Note:Thermal carafe versions  
have no hot plate. Please ensure  
the jug sits correctly on the base  
recess.  
WARNING: The coffee maker  
and hot plates are hot and  
remain hot for some time  
after switching off.  
Ensure the jug · lid is fully  
closed by turning the lid  
clockwise, this ensures the  
maximum temperature is  
maintained in the jug. To ensure  
the coffee is kept as warm as  
possible we advise you rinse  
your thermal carafe in hot water  
before use.  
NOTE:  
F
Remember to turn off the  
machine when you have  
finished.  
Allow the unit to cool.  
Please note the jug lid must be  
in place during the brewing  
process; otherwise the non-drip  
valve will not open, causing the  
filter to flood.  
Remove the permanent filter and  
empty the used coffee grounds.  
Wash the filter immediately and  
dry thoroughly.  
6
7
Select the required strength of  
coffee using the strength  
selector on the lid E.  
Thermal Carafe Variants  
When the brewing process is  
complete the product remains  
on, we recommend you switch  
off your coffee maker as soon as  
brewing is complete.  
Plug the filter coffee maker in at  
the wall socket and switch on,  
the water gauge Ê will  
illuminate. Rotate the dial Ï to  
select one of the two on  
The thermal carafe · will keep  
the coffee warm in the jug for up  
to four hours.  
positions available: 1/2 carafe or a  
full carafe,F depending on the  
number of cups required. Refer  
to ‘Cup selection function’ page  
11 for further information.  
The anti drip valve È will  
prevent any remaining coffee  
dripping onto the base recess  
during serving.  
8
The cup selection indicator  
Ì/Ó and the brewing on  
indicator Ô will light up. The hot  
water will start to flow through  
the coffee grounds and into the  
jug as coffee for you to enjoy.  
We suggest consuming your  
coffee within two hours, after  
this time we suggest brewing  
another jug of fresh coffee.  
Glass Carafe Variant  
WARNING: The coffee maker  
and hot plates are hot and  
remain hot for some time  
after switching off.  
When the brewing process is  
complete the product will  
automatically switch to keep  
warm; the auto keep warm  
indicator will light up.  
NOTE:  
Remember to turn off the  
machine when you have  
finished.  
The automatic keep warm  
function will keep the coffee  
warm in the carafe until the  
product is switched off.  
Allow the unit to cool.  
The anti-drip valve È will  
prevent any remaining coffee  
dripping onto the hot plate  
during serving. Ensure that the  
jug is replaced on the hot plate  
after serving.  
Remove the permanent filter and  
empty the used coffee grounds.  
Wash the filter immediately and  
dry thoroughly.  
6
7
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119  
UK Helpine 0870 060 2614 Repacement Parts 0870 157 6645 Ireland Helpine 1800 409119  
47060 rev2 25/6/07 12:37 Page 8  
G
H
DIGITAL INTERFACE  
Thermal Carafe Variant  
VERSIONS  
Note:Thermal carafe versions  
have no hot plate. Please  
ensure the jug sits correctly on  
the base recess.  
Set the clock  
When the machine is plugged  
in, the display will flash 12:00  
dimly.  
Ensure the jug · lid is fully  
closed by turning the lid  
clockwise, this ensures the  
maximum temperature is  
maintained in the jug. To ensure  
the coffee is kept as warm as  
possible we advise you rinse  
your thermal carafe in hot water  
before use.  
To set the time press the hour  
button ˆ and minute buttons  
˜ to reach the desired time.  
NOTE:The clock is a 24 hour  
clock.  
The clock will be reset, each  
time the product is unplugged  
at the wall.  
Please note the jug lid must be  
in place during the brewing  
process; otherwise the non-drip  
valve will not open, causing the  
filter to flood.  
I
Making coffee  
1
2
Press the push button to  
open the hinged lid. The lid will  
automatically rise G.  
6
7
Select the required strength of  
coffee using the strength  
selector on the lid L.  
J
Using the jug, fill the water  
reservoir ¤ with the required  
amount of water using the level  
indicator Ê as a guide. Both  
the jug and water level indicator  
are marked in cups H.  
Press the power ON/OFF  
selection button Û. The display  
lights up brightly and the cup  
selection indicator will flash 35  
showing the previous selection.  
NOTE: If the machine has been  
unplugged from the wall socket  
since the last operation the  
previous selection will be  
cleared, the default setting will  
be applied (1 full carafe).  
3
Spoon the required amount  
of ground filter coffee into the  
mesh filter spreading evenly.  
We suggest one level measuring  
spoon for every cup. Ensure the  
filter is sitting properly in the  
filter holder I.  
K
8
Press the cup selection button  
¯ to select one of the available  
options, 1/2 carafe or full carafe  
M depending on the number of  
cups required. Refer to ‘Cup  
selection function’ page 11 for  
further information. The  
selection indicator will stop  
flashing, if no buttons are  
pressed for 2 seconds the  
machine will begin the brewing  
process.  
4
5
Close the lid. Ensure the lid is  
closed and latched properly,J  
otherwise the machine will not  
function correctly.  
L
Slide the jug ‡/· into the  
coffee maker ensuring it sits  
correctly on the hot plate K.  
The jug lid must be in place  
during the brewing process;  
otherwise the non drip valve will  
not open, causing the filter to  
flood.  
9
The brewing indicator ˘ will  
start to illuminate from left to  
right indicating that brewing is in  
progress, hot water will start to  
flow through the coffee grounds  
and into the jug as coffee ·.  
M
7
47060 rev2 25/6/07 12:37 Page 9  
Glass Carafe Variant  
Thermal Carafe Variant  
When the brewing process is  
complete the product will  
When the brewing process is  
complete the product remains  
on, the brewing indicator ˘ will  
stop illuminating from left to  
right, all segments will remain  
solidly illuminated, the indicator  
has now changed from a  
automatically switch to keep  
warm ; the brewing indicator  
˘ will stop illuminating from left  
to right. All segments will remain  
solidly illuminated indicating the  
machine is in keep warm state.  
The indicator has now changed  
from a brewing indicator to a  
quality indicator. Refer to ‘Coffee  
Quality indicator’ page 11 for  
further information.  
brewing indicator to a quality  
indicator. Refer to ‘Coffee  
Quality indicator’ page 11 for  
further information.  
If the coffee is to be consumed  
immediately we recommend  
switching off your coffee maker  
as soon as brewing is complete.  
The automatic keep warm   
function will keep the coffee  
warm in the carafe until the  
product is switched off.  
NOTE: If you switch off your  
coffee maker the coffee quality  
indicator will turn off and reset.  
For safety reasons the coffee  
maker will automatically switch  
off after two hours.  
The thermal carafe will keep the  
coffee warm in the jug for up to  
four hours.  
The anti-drip valve È will  
prevent any remaining coffee  
dripping onto the hot plate  
during serving. Ensure that the  
jug is replaced on the hot plate  
after serving.  
For safety reasons the coffee  
maker will automatically switch  
off after two hours.  
The anti drip valve will prevent  
any remaining coffee dripping  
onto the base recess during  
serving.  
We suggest consuming your  
coffee within two hours, after  
this time we suggest brewing  
another jug of fresh coffee.  
We suggest consuming your  
coffee within two hours, after  
this time we suggest brewing  
another jug of fresh coffee.  
WARNING: The coffee  
maker and hot plates are  
hot and remain hot for some  
time after switching off.  
WARNING: The coffee  
NOTE:  
maker and hot plates are  
hot and remain hot for some  
time after switching off.  
Remember to turn off the  
machine when you have  
finished.  
NOTE:  
Allow the unit to cool.  
Remember to turn off the  
machine when you have  
finished.  
Remove the permanent filter and  
empty the used coffee grounds.  
Wash the filter immediately and  
dry thoroughly.  
Allow the unit to cool.  
Remove the permanent filter and  
empty the used coffee grounds.  
Wash the filter immediately and  
thoroughly.  
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119  
9
8  
47060 rev2 25/6/07 12:37 Page 10  
Set the automatic  
timer function  
If setting the automatic timer  
function during the brewing  
process, wait until the process is  
complete before pressing the  
AUTO button.  
NOTE:The timer function can be  
set when the coffee maker is  
brewing or when it is in standby.  
6
7
Press the AUTO button ı again  
to cancel the automatic function,  
the timer function indicator will  
disappear. The machine will keep  
in the memory the cup selection  
setting and the start time until it  
is unplugged from the mains  
socket.  
1
Press the programme button Ù.  
The display will change to show  
the previous set time and cup  
selection flashing. If no previous  
setting has been made or the  
machine has been unplugged  
from the socket since the last  
setting the default setting will be  
shown; 12:00 and full carafe.  
To change the start time and the  
number of cups repeat steps  
1-5.  
2
3
Select ¯ the desired number of  
cups that want to be brewed, 1/2  
or full carafe (see cup selection  
function on page 11). The cup  
selector indicator will stop  
flashing.  
WARNING: Remember to fill  
the water tank with water  
and the filter with coffee  
before activating the auto  
function.  
Press the hour and minute ˜  
buttons to set the desired time.  
The start time will stop flashing.  
NOTE:The clock is a 24 hour  
clock.  
NOTE:The programming mode  
indicator continues to flash to  
show the display is still in  
programming mode.  
If no buttons are pressed, the  
display will revert to the time  
display within 5 seconds.  
4
If the programme button Ù is  
pressed again or if no buttons  
are pressed within 5 seconds  
the cup selection setting and the  
start time are memorised.  
5
To activate the automatic timer  
function press AUTO button ı.  
The display will change to show  
the programmed time and cup  
selection setting for 5 seconds.  
The display will then change to  
show the time, the automatic  
timer function indicator will  
illuminate to show the automatic  
timer function is set.  
With the automatic function  
activated the coffee maker will  
turn on at the desired time and  
start to brew the coffee.  
NOTE: If the AUTO button ı is  
pressed during the brewing  
process the machine will switch  
off and the automatic timer  
function will be activated.  
9
47060 rev2 25/6/07 12:37 Page 11  
N
Frothing milk  
Pour the coffee into the cups  
and then gently pour or  
preferably spoon the milk onto  
the coffee.  
It is advised to start heating your  
milk ready for frothing when you  
start making the coffee. This  
helps to ensure the milk reaches  
its optimum frothing  
WARNING: The stainless  
steel jug and the hotplate  
will remain hot for  
sometime after switching  
the machine off.  
temperature.  
1
2
Fill the stainless steel jug with  
the required amount of milk. Do  
not exceed the maximum level.  
O
NOTE:The milk frother jug and  
lid can be disassembled for easy  
cleaning.  
Place the jug on the hot plate Î  
N and push the frother hot  
plate  ON/OFF switch to the  
‘ON’ O position, the hot plate  
indicator will light up.  
It is recommended that you  
disassemble and clean the milk  
frother jug and its components  
immediately after use, as dried  
milk can be difficult to remove.  
3
4
Once the coffee is brewed (and  
the auto keep warm indicator  
lights up) the milk is ready to  
froth.  
NOTE: All milk jug and coffee jug  
components are dishwasher  
safe for easy cleaning.  
P
Engage the frother system by  
turning the frother control lever  
P ‰ to the right, the motor will  
start automatically and the milk  
frother device ON indicator will  
illuminate Ò.  
Frothing should take between  
30-60 seconds.  
NOTE: Frothing time can vary  
depending on the type of milk  
used and its starting  
temperature. We recommend to  
use semi skimmed milk from the  
fridge.  
Q
5
Disengage the frother system  
from the jug by turning the  
frother control lever to the left Q  
, the motor will stop  
automatically. Push and release  
the milk hot plate switch to turn  
off the hot plate Â.  
WARNING: Take care the  
milk will be very hot.  
Remove the milk jug from the  
hot plate and press the lid  
release button Í to disengage  
the lid. The lid assembly can be  
removed for easy pouring and  
spooning off the milk.  
NOTE:The lid can be turned  
upside down and rest on the  
work surface. The inner lid is  
shaped to collect any dripping  
milk and froth for minimal mess.  
10  
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119  
47060 rev2 25/6/07 12:37 Page 12  
Cup selection  
function  
Coffee quality  
indicator  
1
This machine has a special  
selector that maintains the  
quality of coffee brewed in  
relation to the number of cups  
selected.  
The coffee quality indicator will  
show the quality of the coffee in  
the carafe in relation to the time  
since brewing was completed.  
Quality of the coffee is a  
personal choice. The quality  
indicator gives an indication of  
the quality and taste of coffee  
after the brewing process is  
complete.  
There are two options available:  
1
/2 carafe (1-6 cups - Glass jug)  
(1-5 cups -Thermal jug)  
It is not absolute and can differ  
due to personal taste, or type of  
coffee used.  
1 carafe (7-12 cups - Glass jug)  
(6-10 cups -Thermal  
jug)  
The graph shown below gives  
an indication of the relation  
between each segment of the  
display in relation to both quality  
and time.  
2
3
The selection needs to be set in  
relation to the amount of water  
in the water tank and the  
amount of coffee powder in the  
filter.  
B
C
D
The incorrect selection of this  
function will not affect the  
functionality of the machine  
however the quality and taste of  
the coffee brewed will be  
affected.  
A
E
4
If you find the strength selector  
does not provide a weak or  
strong enough cup of coffee to  
suit your taste, the cup selection  
function can be used in  
conjunction to achieve a  
stronger or weaker cup of  
coffee.  
The table below shows the  
settings to use in relation to the  
volume of water in the tank to  
help achieve a stronger or  
weaker coffee. Feel free to  
experiment with different  
settings until you achieve the  
desired strength of coffee to suit  
your own personal taste.  
1-6  
1-5  
7-12  
6-10  
1/2  
1
Standard  
Stronger  
Weaker  
Standard  
11  
47060 rev2 25/6/07 12:37 Page 13  
RECIPES  
Cafe Latte  
1/2 espresso  
5
Pour the coffee, hot milk  
and hot chocolate into a tall  
glass and serve.  
Cappuccino  
1/3 espresso  
1/2 hot frothed milk  
Irish Coffee  
Makes 2 servings  
1/3 hot milk  
1
2
Prepare coffee as per  
‘making a coffee’  
1/3 hot frothed milk  
instructions (5, 6 or 7).  
40ml of double cream  
2 tsp sugar  
Chocolate powder for  
sprinkling  
Fill the stainless steel milk  
jug with the required  
1
2
Prepare coffee as per  
‘making a coffee’  
instructions (Page 5, 6 or  
7).  
amount of milk, place on  
the hotplate and switch on.  
The milk will take approx. 7  
minutes to reach the  
4 shot measurements of  
Irish whisky  
350ml hot strong coffee  
appropriate temperature.  
Fill the stainless steel milk  
jug with the required  
1
2
Whip double cream until  
thick then chill.  
3
Froth milk by lifting the milk  
jug up to the milk frothing  
blade ensuring that the  
blade is just under the  
surface of the milk and  
press the milk frothing  
button. The milk will take  
approx. 30-60 seconds to  
froth.  
amount of milk, place on  
the hotplate and switch on.  
The milk will take approx. 7  
minutes to reach the  
Warm 2 Irish coffee glasses  
with hot water and place in  
each a teaspoon of sugar  
and 2 shots of Irish whisky  
in glass.  
appropriate temperature.  
3
Froth milk by lifting the milk  
jug up to the milk frothing  
blade ensuring that the  
blade is just under the  
surface of the milk and  
press the milk frothing  
button. The milk will take  
approx. 30 seconds to  
froth.  
3
4
Divide coffee among the  
glasses.  
4
Pour the coffee into a tall  
glass and top with the  
frothed milk.  
Slowly dribble the chilled  
cream over the back of the  
spoon onto the top of the  
coffee.  
Moccacino  
1/3 espresso  
5
Do not stir.  
4
5
Pour the coffee in first and  
then the hot milk into a  
cappuccino cup, spoon  
over frothed milk.  
1/3 hot frothed milk  
1/3 hot chocolate  
Sprinkle with chocolate  
powder to serve.  
1
2
Prepare coffee as per  
‘making a coffee’  
instructions (5, 6 or 7).  
Amaretto Coffee  
Fill the stainless steel milk  
jug with the required  
250ml hot strong coffee  
amount of milk, place on  
the hotplate and switch on.  
The milk will take approx. 7  
minutes to reach the  
2 tablespoons of double or  
whipped cream  
2 shots of Amaretto  
Sugar to taste  
appropriate temperature.  
3
4
Froth milk by lifting the milk  
jug up to the milk frothing  
blade ensuring that the  
blade is just under the  
surface of the milk and  
press the milk frothing  
button. The milk will take  
approx. 30 seconds to  
froth.  
1
2
Stir the coffee and alcohol  
together either with 2  
tablespoons of double-  
cream, or top with a dollop  
of whipped cream.  
Sprinkle with grated  
chocolate and serve.  
Prepare the hot chocolate  
according to the  
manufacturer’s instructions.  
12  
UK Helpline 0870 060 2610 Replacement Parts 0870 167 6641 Ireland Helpline 1800 409119  
47060 rev2 25/6/07 12:37 Page 14  
CLEANING AND  
Cleaning care  
MAINTENANCE  
1
2
3
Unplug the coffee maker, and  
allow to cool.  
Refilling  
Switch off the coffee maker, and  
allow 5 minutes to cool.  
Do not immerse the coffee  
maker in liquid.  
1
2
Rinse the water tank  
Lift the lid and refill with cold  
water.  
occasionally with cold water. Do  
not use a cloth as any residue or  
lint left behind may clog the  
coffee maker.  
Descaling  
4
5
Remove the permanent filter ›  
and filter holder discard the  
used coffee and wash with  
warm soapy water. Extended  
soaking is recommended at the  
same time as descaling. Rinse  
and dry thoroughly.  
If you live in a harder water area,  
we recommend that your coffee  
maker is descaled at regular  
intervals, eg. every 2 - 3 months.  
In areas of moderately hard  
water you should descale every  
6 months.  
Wash the coffee jug and milk jug  
including all frothing  
components, in warm soapy  
water. Rinse and dry all parts  
thoroughly.  
If the water filters through more  
slowly than usual, it is a sign  
that descaling is necessary.  
We recommend you to use  
proprietary liquid descaler which  
is especially made for coffee  
makers and plastic kettles.  
Follow the instructions on the  
bottle or sachet, and then  
operate the coffee maker with  
just water 3 times before making  
coffee.  
NOTE: Coffee jug, milk jug and  
frother parts are all dishwasher  
safe.  
6
Wipe all external surfaces with a  
damp cloth and dry thoroughly.  
Care must be taken to ensure  
the non drip valve situated on  
the bottom of the filter holder is  
not damaged during cleaning.  
Do not use kettle descaler  
unless the packet specifically  
states it is suitable for coffee  
makers.  
Never use harsh or abrasive  
cleaners.  
NOTE:The permanent mesh  
filter should not be in place  
during descaling.  
13  
47060 rev2 25/6/07 12:37 Page 15  
Helpline  
If you have any difficulty with  
your appliance, do not hesitate  
to call. We are more likely to be  
able to help than the store from  
where you bought it.  
Please have the following  
information ready to enable our  
staff to deal with your enquiry  
quickly:  
Name of the product.  
Model number as shown on the  
underside of the appliance.  
Serial number as shown on  
underside of the appliance.  
For electrical products sold  
within the European  
Community:  
At the electrical products useful  
life it should not be disposed of  
with household waste.  
Please recycle where facilities  
exist.  
Check with your Local Authority  
or retailer for recycling advice in  
your country.  
UK Helpline  
0870 060 2610  
0870 167 6641  
1800 409119  
Replacement Parts  
Ireland Helpline  
UK Helpline 0870 060 2614 Replacement Parts 0870 157 6645 Ireland Helpline 1800 409119  
14  
47060 rev2 25/6/07 12:37 Page 16  
YOUR TWO YEAR  
EXCLUSIONS  
GUARANTEE  
Morphy Richards shall not be liable  
to replace or repair the goods under  
the terms of the guarantee where:  
It is important to retain the retailers  
receipt as proof of purchase. Staple  
your receipt to this back cover for  
future reference.  
1
The fault has been caused or is  
attributable to accidental use,  
misuse, negligent use or used  
contrary to the manufacturers  
recommendations or where the fault  
has been caused by power surges or  
damage caused in transit.  
Please quote the following  
information if the product develops a  
fault. These numbers can be found  
on the base of the product.  
Model no.  
Serial no.  
2
3
4
5
6
The appliance has been used on a  
voltage supply other than that  
stamped on the products.  
All Morphy Richards products are  
individually tested before leaving the  
factory. In the unlikely event of any  
appliance proving to be faulty within  
28 days of purchase it should be  
returned to the place of purchase for  
it to be replaced.  
Repairs have been attempted by  
persons other than our service staff  
(or authorised dealer).  
Where the appliance has been used  
for hire purposes or non domestic  
use.  
If the fault develops after 28 days  
and within 24 months of original  
purchase, you should contact the  
Helpline number quoting Model  
number and Serial number on the  
product, or write to Morphy Richards  
at the address shown.  
Morphy Richards are not liable to  
carry out any type of servicing work,  
under the guarantee.  
Plastic filters for all Morphy Richards  
kettles and coffee makers are not  
covered by the guarantee.  
You may be asked to return a copy  
of proof of purchase  
This guarantee does not confer any  
rights other than those expressly set  
out above and does not cover any  
claims for consequential loss or  
damage. This guarantee is offered as  
an additional benefit and does not  
affect your statutory rights as a  
consumer.  
Subject to the exclusions set out  
below (see Exclusions) the faulty  
appliance will then be repaired or  
replaced and dispatched usually  
within 7 working days of receipt.If for  
any reason this item is replaced  
during the 2 year guarantee period,  
the guarantee on the new item will  
be calculated from original purchase  
date. Therefore it is vital to retain  
your original till receipt or invoice to  
indicate the date of initial purchase.  
This guarantee is valid in the UK and  
Ireland only.  
For electrical products sold  
within the European  
Community. At the end of  
the electrical products  
useful life it should not be  
disposed of with household  
waste.  
Please recycle where  
facilities exist. Check with  
your Local Authority or  
retailer for recycling advice  
in your country.  
To qualify for the 2 year guarantee  
the appliance must have been used  
according to the manufacturers  
instructions. For example coffee  
makers should have been regularly  
descaled.  
The After Sales Division  
Morphy Richards Ltd  
Mexborough, SouthYorkshire,  
England, S64 8AJ  
Morphy Richards products are intended for household use only.  
Registration 644702  
Morphy Richards has a policy of continuous improvement in product quality and  
design. The company, therefore reserves the right to change the specification of its  
models at any time.  
Helpline (office hours)  
UK 0870 060 2610  
Republic of Ireland 1800 409119  
47060 MUK Rev2 06/07  
For details of other products in the Morphy Richards range please see our website . . .  

Motorola MOTO 68000202973 B User Manual
Motorola Karma QA1 User Manual
Marantz Reference Series SA 11S1 User Manual
LG Electronics Optimus S User Manual
Kenwood KRC 666 User Manual
IBM 48X User Manual
Bunn ES1A User Manual
Billy Goat TKD505SPT User Manual
Apple Xserve G5 User Manual
Addonics Technologies ZHDUESA User Manual