Miele CVA4075 User Manual

Operating and Installation  
Instructions  
Coffee System  
with convertible water connection  
CVA 4075  
en - US, CA  
To prevent accidents  
and machine damage  
read these instructions  
before  
installation or use.  
M.-Nr. 07 194 220  
Contents  
Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35  
Descaling the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45  
Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47  
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54  
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55  
Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56  
Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57  
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58  
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59  
Adjusting the door hinges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61  
3
IMPORTANT SAFETY INSTRUCTIONS  
When using electrical appliances basic safety precautions should always be  
followed, including the following:  
Read all instructions before installation or use of the coffee system.  
Be certain your appliance is  
~
Please read these instructions  
carefully to prevent accidents and  
machine damage.  
properly installed and grounded by a  
qualified technician. To guarantee the  
electrical safety of this appliance,  
continuity must exist between the  
appliance and an effective grounding  
system. It is imperative that this basic  
safety requirement be met. If there is  
any doubt, have the electrical system of  
the house checked by a qualified  
electrician. The manufacturer cannot be  
held responsible for damages caused  
by the lack, or inadequacy, of an  
effective grounding system.  
This appliance complies with current  
safety requirements. Improper use  
of the appliance can cause personal  
injury and material damage.  
This appliance is for household use  
only, to prepare espresso,  
cappuccino and coffee.  
Do not use appliance other than for  
its intended use. Any other use  
could be dangerous.  
Do not use an extension cord to  
~
connect the appliance to electricity.  
Extension cords do not guarantee the  
required safety of the appliance  
(danger of overheating).  
The manufacturer cannot be held  
responsible for damage caused by  
improper use of the appliance.  
Before service or maintenance  
~
disconnect the power supply by either  
removing the fuse, “tripping” the circuit  
breaker or unplugging the unit.  
Electrical safety  
Before connecting the appliance to  
~
the electrical supply make sure that the  
voltage and frequency listed on the  
data plate correspond with the  
Install or locate this appliance only  
~
in accordance with the provided  
installation instructions.  
household electrical supply. If in doubt,  
consult a qualified technician.  
The appliance must be properly  
~
installed before operation to ensure that  
no electrical components are  
accessible. Ensure that power is not  
supplied to the appliance while  
installation work, repairs or  
maintenance is performed.  
4
IMPORTANT SAFETY INSTRUCTIONS  
Installation work and repairs must  
Do not operate any appliance with a  
~
~
only be performed by a trained  
technician in accordance with national  
and local safety regulations. Repairs  
and other work by unauthorized  
persons could be dangerous and may  
void the warranty.  
damaged cord or plug, or after the  
appliance malfunctions or has been  
damaged in any manner. Contact  
Miele.  
Always attach the cord to the  
~
appliance first, then plug it into the wall  
outlet. To disconnect, turn the machine  
off, then remove the plug from the wall  
outlet.  
Only use Miele original spare parts.  
~
Only then can the manufacturer  
guarantee the safety of this machine.  
Never open the outer casing of the  
The unit is designed for a cold water  
~
~
appliance. Tampering with electrical  
connections or components and  
mechanical parts is dangerous and  
may cause machine damage.  
connection. Do not connect it to hot  
water, it will get damaged.  
The water supply must be  
~
accessible after installation.  
If the machine is installed in  
~
Do not damage or kink the cover of  
~
combination with other appliances, a  
protective base should be installed  
between the appliance and the unit.  
the water intake hose.  
The waterproof system will only work if:  
~
– it is installed correctly.  
Do not install or use outdoors even if  
~
– it is damaged, the machine repaired  
or faulty parts replaced.  
installed in the display cabinet.  
To protect against fire, electric  
– the water supply is shut off when not  
using the coffee system for an  
extended period of time,  
~
shock and injury to persons do not  
submerge the cord or plugs in water or  
other liquids.  
e.g. vacationing.  
Do not let the cord hang over the  
~
edge of a table or counter, or touch hot  
surfaces.  
5
IMPORTANT SAFETY INSTRUCTIONS  
Use  
To avoid injuries allow the coffee  
~
system to cool before cleaning or  
putting on and taking off parts. Turn the  
machine off at the main switch when  
not in use and before cleaning.  
The coffee system must be  
maintained daily to prevent the  
growth of harmful bacteria and  
mold. Please read the “Cleaning and  
care” section of this booklet. All  
parts are dishwasher safe except  
the brew unit and bean container.  
When using the coffee system with  
~
the water tank, only fill the water tank  
with cold, fresh tap water. Warm or hot  
water, or any other liquids may damage  
the machine.  
Caution! Do not look directly or with  
an optical instrument into the  
lighting - laser radiation.  
The water should be changed daily  
~
to prevent bacteria or mold growth.  
Do not use mineral water. Mineral  
~
water leads to heavy calcium buildup in  
the machine that can damage the unit.  
Caution! Risk of burns when  
dispensing hot beverages, they are  
extremely hot.  
Do not fill anything but coffee beans  
~
into the beans container. Do not fill  
ground coffee in the beans container, it  
will damage the grinding unit.  
Persons which lack physical,  
~
sensory or mental abilities or  
Do not fill anything but ground  
~
experience with the machine should not  
use it without supervision or instruction  
by a responsible person.  
coffee or a cleaning tablet (for the brew  
unit) in the funnel for ground coffee,  
otherwise it will get damaged.  
Close supervision is necessary  
~
Sugar can damage the appliance!  
~
when any appliance is used by or near  
children.  
Caramelized or otherwise pre-treated  
coffee beans or other sugar containing  
beverages must not be put in the  
machine.  
Do not touch hot surfaces. Use  
~
handles or knobs.  
Rinse the lines and the froth  
~
dispenser, and clean the unit before the  
first use.  
6
IMPORTANT SAFETY INSTRUCTIONS  
Never place a cup with an  
Depending on the fat content of the  
~
~
alcohol-coffee mixture underneath the  
coffee dispenser. Plastic parts of the  
unit could catch fire!  
coffee, the brew unit may clog. Clean  
the brew unit every 200 cups with a  
cleaning tablet. The display shows a  
respective request.  
The hot water and steam dispensed  
~
could cause scalding. These functions  
Dispose of the coffee waste in a  
~
must be used carefully. Never hold any trash can, not in the sink. The sink  
parts of the body under the steam  
nozzle or the hot water dispenser. The  
machine must never be used to clean  
objects.  
could get clogged.  
Do not hang, lean, sit or place heavy  
~
items on the door. The machine could  
be damaged.  
Do not use the machine when the  
~
The use of accessory attachments  
~
froth dispenser is removed. Danger of  
scalding with hot steam!  
not recommended by the appliance  
manufacturer may result in fire, electric  
shock or injury to persons.  
Never use a steam cleaner to clean  
~
the appliance. Pressurized steam could  
damage electrical components and  
cause a short circuit.  
SAVE THESE  
INSTRUCTIONS  
The appliance must be descaled  
~
regularly with the supplied descaling  
tablets. In areas with very hard water  
the machine may need to be descaled  
more often. The manufacturer cannot  
be held responsible for damages  
resulting from insufficient descaling.  
Only use the descaling tablets  
~
provided by Miele. Take care to use the  
correct mixture of water and descaler,  
otherwise it may cause damage.  
7
Guide to the machine  
Front view  
a Touch controls  
(lowest control "On/Off" button)  
g Bottom lighting  
h Plastic drip tray  
i Metal drip tray  
b Display  
c Touch controls  
(lowest control "Clear" button)  
j Coffee dispenser  
(height adjustable)  
d Top lighting  
e Door grip  
k Froth dispenser  
(removable for better cleaning)  
f Hot water spout  
l Intake hose  
(removable together with dispenser)  
8
Guide to the machine  
Interior view  
a Main switch  
b Cover for ground coffee funnel  
c Funnel for ground coffee  
d Grind control lever  
e Coffee bean container  
f Drip tray with no-spill grid for transport  
g Water tank (with water inlet valve)  
h Brew unit  
i Waste unit  
9
First steps to use  
Touch controls  
Turning on  
Select a touch control with your  
fingertip to use the machine.  
^ Select "On/Off" to turn the coffee  
system on.  
The display shows the clock. See  
"Settings - Clock - Setting the time of  
day" to set the time.  
Display  
To select a menu, select the touch  
control next to the respective menu  
point.  
During the very first use, you will be  
prompted to select a language.  
If more features can be selected under  
one menu point, the menu has three  
dots (e.g. "Settings...").  
^ Select the desired language touch  
control and then "OK".  
The J symbol indicates the "Language"  
setting. If you accidentally select an  
unfamiliar language, simply look for the  
J symbol. Touch the control next to the  
flag symbol and select your language  
of choice.  
"more" / "back": If there are more  
menus which are not immediately  
shown, select "more" or "back" to see  
further options.  
"Clear": to go back to the previous  
screen.  
^ Customize the coffee system to your  
desired settings.  
"Stop": to cancel coffee preparation.  
"OK": to save a setting.  
Prepare two cups of coffee and  
dispose of them, this will clean any  
coffee residues from the brew unit  
left from the quality control tests at  
the factory.  
Before the first use  
The appliance must be correctly  
installed and connected before the  
first use. See "Electrical connection",  
"Plumbing" and "Installation  
instructions".  
Turning off  
^ Select "On/Off".  
The display shows the time of day. After  
60 seconds the display turns off  
(depending on the setting). See  
"Settings - Clock".  
Clean the appliance and remove  
protective foils before the first use.  
See "Cleaning and Care".  
If the rinse automatic feature is  
turned on the machine will begin  
rinsing if a coffee was prepared that  
day.  
10  
Filling water, beans or ground coffee  
Before using the coffee system for  
the first time, clean the appliance.  
See "Cleaning and Care".  
Filling the water tank  
The beans and the water quality is  
important for a good espresso or  
coffee. If the machine is plumbed to a  
water line and turned on, the water tank  
is automatically filled. Empty the water  
tank daily. The unit displays a reminder  
when turned on.  
^ Open the appliance door by  
grasping the recess next to the hot  
water spout and pulling the door  
towards you.  
When using the coffee system with the  
water tank, only fill the water tank with  
cold, fresh tap water.  
Never add hot water or any other  
liquids except cold water to the  
water tank.  
^ Pull the water tank out.  
^ When using the coffee system with  
the water tank, fill the tank with fresh,  
cold tap water to the "Max." mark.  
Do not use mineral water. Mineral  
water leads to heavy calcium  
built-up in the machine that can  
damage the unit.  
A valve at the front of the tank prevents  
leaks.  
^ Close the lid and push the water tank  
into the unit until it clicks into place.  
The water tank must be positioned  
correctly or the valve will leak. If the  
water tank has not clicked into  
place, pull the tank out, check and  
clean the niche.  
11  
Filling water, beans or ground coffee  
Filling the beans container  
Filling ground coffee  
A funnel for ground coffee is provided  
in case you would like to prepare a  
different coffee type, e.g. decaffeinated  
coffee.  
Only fill espresso or coffee beans in  
the beans container. Anything else -  
including ground coffee - will  
damage the grinding unit.  
Caramelized or otherwise  
pre-treated beans or sugar  
containing beverages must not be  
filled into the appliance. It will  
damage the coffee system.  
^ Pull the bean container out.  
^ Pull the cover for the ground coffee  
funnel out of the appliance and lift the  
funnel lid, a.  
^ Place one spoonful of ground coffee  
into the funnel, b, (using the  
supplied spoon) and close the lid.  
^ Push the cover into the appliance  
and close the door.  
^ Push the lid back and fill the  
container with roasted coffee beans.  
See "Making Coffee - Espresso and  
coffee made from ground coffee".  
^ Push the lid back into place and put  
the beans container back into the  
appliance.  
^ Close the door.  
12  
Making coffee  
Turning on  
The lines must be rinsed daily  
^ Select the "On/Off" touch control.  
before the first use. This will happen  
automatically if "Rinse automatic" is  
set to "On" (see "Settings - Rinse  
Automatic") and the machine is cold.  
After heating, hot water runs out of  
the two spouts into the drip tray. If  
"Rinse automatic" was set to "Off",  
use "Care" to rinse the lines. See  
"Cleaning and Care - Rinse".  
Please empty the water tank  
i
^ Empty the water tank when turning  
the machine on, to ensure that only  
fresh tap water is used to prepare  
coffee.  
Then the upper line in the display  
shows:  
Preheating  
+ DESCALING  
+ USER PROFILE: STANDARD  
+ SETTINGS F ...  
If "Rinse automatic" is set to "On"  
(default), the machine rinses after the  
heating phase and the main menu is  
displayed.  
13  
Making coffee  
Pre-warming cups  
Adjust the dispenser height  
All beverages should be made in a  
warm cup, to develop the aroma. The  
smaller the amount of coffee or  
espresso and the thicker the cups, the  
more important it is to pre-warm the  
cups.  
Depending on the cup height, the  
coffee dispensers can be adjusted so  
that the coffee and espresso have a  
shorter distance to the cup, do not cool  
and have a better crema.  
^ Set the cup under the hot water  
spout.  
+ ESPRESSO  
+ COFFEE  
HOT WATER ~  
MILK FROTH ~  
more ~  
+ CAPPUCCINO  
^ Select "Hot water" from the main  
menu.  
^ Pull the coffee dispenser slowly up or  
down.  
^ Hot water is dispensed. Select "Stop"  
to stop the flow.  
^ Let the hot water sit for a moment to  
pre-warm the cup, then empty the  
cup.  
14  
Making coffee  
Espresso and coffee made  
from coffee beans  
Preparing two cups at the same time  
^ Set a cup under each coffee  
dispenser.  
^ Set a cup under the coffee  
dispenser.  
^ Select "Espresso" or "Coffee".  
The drink is dispensed through both  
dispensers at the same time.  
^ Select "2 portions" when displayed.  
The coffee system makes two portions  
of espresso or coffee with a few  
seconds in between.  
^ Select "Espresso" or "Coffee".  
The machine grinds the beans and  
pre-brews the coffee (if "On" is selected  
under "Pre-brewing"). The selected  
beverage is dispensed.  
Keep the cups under the dispenser  
until the main menu shows in the  
display.  
Do not open the door during  
brewing. The machine will be  
damaged.  
Canceling  
^ Select "Stop" to cancel the process.  
The portion sizes for espresso, coffee  
and cappuccino can be set  
individually. See "Setting the serving  
sizes".  
15  
Making coffee  
Espresso and coffee made  
from ground coffee  
Preparing two cups at the same time  
When using ground coffee, only one  
portion at a time can be prepared. The  
unit uses the whole portion of ground  
coffee which was filled in the funnel to  
prepare one drink.  
After filling the funnel with ground  
coffee (see "Filling water, beans or  
ground coffee - Filling ground coffee"),  
the display shows:  
Did you fill ground coffee and  
i
No  
do you want to prepare it?  
+
Yes ~  
^ Select "Yes".  
Select "No" if no ground coffee is filled  
in the funnel. Otherwise the coffee  
system assumes that ground coffee is  
in the machine and dispenses only  
water next time coffee is made.  
^ Set a cup under the coffee  
dispenser.  
The drink is dispensed through both  
dispensers at the same time.  
^ Select "Espresso" or "Coffee".  
The coffee system brews the espresso  
or coffee and the drink is dispensed.  
Do not open the door during the  
brewing process. It will damage the  
machine. The unit will switch  
automatically back to brewing with  
beans after preparation.  
Canceling  
^ Select "Stop" to cancel the process.  
16  
Making coffee  
Cappuccino and milk froth  
When using for the first time or using  
after descaling  
The lines were completely drained  
before the unit left the factory. They will  
also be drained when the machine is  
descaled. Before preparing  
cappuccino or froth, the lines must be  
filled with water.  
^ Set a cup under the cappuccino  
dispenser.  
^ Select "Milk froth".  
The intake hose takes in water from the  
tank and fills the lines with water. A  
small amount of water runs from the  
froth dispenser.  
Prompts to clean the froth dispenser  
appear in the display.  
^ Confirm by selecting "OK".  
^ Once the machine stops, select "Milk  
froth" again.  
The froth dispenser dispenses steam  
and the lines are filled with water.  
^ Select "Clear" to get back to the main  
menu.  
The coffee system is ready to use.  
17  
Making coffee  
Cappuccino  
Milk froth  
To prepare a cappuccino you need a  
large ceramic or porcelain cup and a  
small mug (supplied) of milk.  
If you need additional milk froth,  
prepare cold skim milk in a stainless  
steel mug which narrows towards the  
top.  
The best milk froth is achieved with  
cold milk.  
^ Set the supplied glass mug with milk  
under the intake hose and the  
stainless steel mug under the froth  
dispenser.  
Only one cup of cappuccino can be  
prepared at a time because of the  
milk frothing process.  
^ Select "Milk froth".  
The milk is frothed into the stainless  
steel mug.  
^ Select "Stop" to cancel the milk  
frothing.  
After preparing milk froth and  
cappuccino  
Clean the froth dispenser and intake  
hose immediately after use. If the milk is  
allowed to dry, the parts may get  
clogged and difficult to clean. See  
"Cleaning and Care".  
^ Set the mug of milk under the intake  
hose and the cup under the froth  
dispenser.  
^ Select "Cappuccino".  
The milk is frothed into the cup. At the  
same time the beans are ground.  
Select "Stop" to cancel the milk frothing.  
^ Once the milk is frothed, set the  
cappuccino cup under both  
dispensers and select "OK".  
The cappuccino will be prepared.  
^ Select "Stop" when enough espresso  
has been prepared.  
18  
Adjusting the coffee grinder  
The amount of ground coffee  
determines the strength of the coffee  
and the quality of the crema.  
To adjust the grinder setting  
The amount of ground coffee can be  
adjusted in the main menu. See  
"Settings - Grind amount".  
To prevent machine damage adjust  
the coffee grinder one notch at a  
time and let the beans grind before  
adjusting another notch. Otherwise  
the machine will be damaged.  
^ Push the slide control to the left for a  
finer grind or to the right for a coarser  
grind.  
You should be able to feel the notches  
when moving the slide control.  
The grinder should be adjusted:  
If the slide control will not move:  
– If the espresso flows too quickly into  
the cup, the pressure cannot be built  
up because the beans have been  
ground too coarsely. The grinder  
should be adjusted to a finer setting.  
^ Close the machine and dispense a  
cup of coffee.  
Then try to move the slide control  
again.  
– If the espresso only trickles into the  
cup, the beans have been ground  
too fine and the coffee will be bitter.  
The grinder should be adjusted to a  
coarser setting.  
– If the crema is evenly colored but  
pale, the ground coffee is too  
coarse.  
– If the crema is very dark brown on  
one side, graduating almost to white  
on the other, the ground coffee is too  
fine.  
19  
Settings  
The coffee system can be customized  
to suit individual preferences.  
Language  
To show the displays in the desired  
language, select the language before  
the first use.  
Preheating  
+ DESCALING  
+ USER PROFILES: STANDARD  
+ SETTINGS F ...  
^ Select "Settings" from the main menu  
during the pre-heating phase or,  
+ back  
SETTINGS F ... ~  
+ CARE ...  
+ USER PROFILES  
^ in the main menu.  
SETTINGS  
+ LANGUAGE F ...  
+ CLOCK  
GRIND AMOUNT ... ~  
PRE-BREWING ~  
more ~  
+ TIMER ...  
^ Select "Language".  
LANGUAGE english  
+ english  
+ deutsch  
+ español  
français ~  
more ~  
OK ~  
^ Select the desired language.  
To see more language options, select  
"more".  
The language options are:  
English, German, Español, Français,  
Italiano, Polski and Portugués.  
^ Select "OK" to save the selection.  
All displays are shown in the selected  
language.  
^ To go back to the main menu, select  
"Clear".  
20  
Settings  
Clock  
Clock display size  
The size of the clock display can be  
adjusted. The options are "normal" or  
"large".  
+ back  
SETTINGS F ... ~  
+ CARE ...  
+ USER PROFILES  
^ Select "Size".  
^ Select "Settings".  
The selected size is highlighted in the  
display.  
SETTINGS  
+ LANGUAGE F ...  
+ CLOCK  
GRIND AMOUNT ... ~  
PRE-BREWING ~  
more ~  
^ Select "Size" until the desired size is  
highlighted.  
+ TIMER ...  
^ Select "OK" to save the selection.  
^ Select "Clock".  
12 or 24 hour clock  
Setting the time of day  
The clock display can be set to the 12  
or 24 hour clock.  
^ Select "Enter Time".  
^ Select the respective touch control.  
The selected display is highlighted.  
^ Select "OK" to save the selection.  
^ Select "+" or "-" with the right touch  
controls to select the hours.  
^ Set the minutes by selecting  
"Minutes".  
^ Select "+" or "-" with the right touch  
controls to select the minutes.  
Clock display on/off  
The clock can be displayed or turned  
off.  
^ Select "OK".  
The time of day is saved.  
If the display is turned on, the time of  
day is displayed when the machine is  
turned off.  
If the option is set to off, the display  
turns off after 60 seconds.  
^ Select "Clock display".  
The selected display is highlighted.  
^ Select "OK" to save the selection.  
21  
Settings  
Timer  
Turn on at  
A specific time of day can be set to turn  
the machine on, e.g. for breakfast.  
Setting a timer  
^ Select "Turning on at".  
+ back  
SETTINGS F ... ~  
^ Set the hours to when the appliance  
should turn on by selecting "+" or "–".  
+ CARE ...  
+ USER PROFILES  
^ Select "Settings".  
^ Switch to "Minutes" and repeat.  
^ Select "OK".  
SETTINGS  
+ LANGUAGE F ...  
+ CLOCK  
GRIND AMOUNT ... ~  
PRE-BREWING ~  
more ~  
The machine will turn on every day at  
the selected time.  
+ TIMER ...  
If the "Rinse" function was set to  
"On", the lines will be rinsed when  
the machine is turned on.  
^ Select "Timer".  
^ Select "Setting".  
If the machine is turned on  
automatically three times and no  
beverages were dispensed, the  
machine will no longer turn on  
automatically. The programmed  
times stay saved and will be  
activated again when the machine is  
manually turned on the next time.  
This safety measure is designed so  
that the machine does not turn on  
every day if the setting was not  
canceled before a longer time of  
absence, e.g. vacationing.  
22  
Settings  
Turn off after  
Turn off at  
The machine will turn off automatically  
to save energy after a programmed  
period of time. Time periods between  
15 minutes and 6 hours can be  
A specific time of day can be set to turn  
the coffee system off.  
^ Select "Turning off at".  
selected. If the machine is not used  
after dispensing beverages, it will turn  
off after the selected time.  
^ Set the hour when the appliance  
should turn on by selecting "+" or "–".  
^ Switch to "Minutes" and repeat.  
^ Select "Turning off after".  
^ Select "OK" to save the selection.  
For example a 0:15 display means that  
the unit will turn off after 15 minutes of  
no use.  
The machine will turn off at the selected  
time.  
^ Select "Clear" until the display shows  
the desired menu.  
^ Set the hour when the appliance  
should turn off by selecting "+" or "–".  
If rinsing is set to "On" and a  
beverage was already dispensed, the  
lines will be automatically rinsed  
before turning off.  
^ Switch to "Minutes" and repeat.  
^ Select "OK" to save the selection.  
The machine will turn off after the  
desired time.  
If rinsing is set to "On" and a  
beverage was already dispensed, the  
lines will be automatically rinsed  
before turning off.  
23  
Settings  
Activating a timer  
The timer function "Turning on at" or  
"Turning off at" can be activated or  
deactivated.  
+ back  
SETTINGS ~  
^ Select "Activate".  
+ CARE ...  
+ USER PROFILES  
^ Select "On" to activate the desired  
function.  
^ Select "Settings".  
SETTINGS  
Select "Off" to deactivate the desired  
function. The selected times in the  
function will stay stored in the  
memory.  
+ LANGUAGE F ...  
+ CLOCK  
GRIND AMOUNT ... ~  
PRE-BREWING ~  
more ~  
+ TIMER ...  
^ Select "Timer".  
^ Select "OK" to confirm the setting.  
24  
Settings  
Grind amount  
Pre-brewing  
The grind amount can be set,  
During pre-brewing a small amount of  
depending on the coffee type, between water is released onto the ground  
0.2 ounces and 0.5 ounces  
coffee. After a short time the remaining  
water is pushed through the ground  
coffee at a high pressure.  
(6 - 14 grams). The more the coffee is  
ground the stronger the espresso,  
coffee or cappuccino will be.  
If the function is turned off, the hot  
water will be immediately pushed at a  
high pressure through the ground  
coffee.  
The crema is also influenced by the  
grind amount.  
– If the crema has an even but  
white/yellow coloring, the ground  
amount might be too little.  
Pre-brewing is set to off by default.  
^ Select the User profile, for which you  
would like to set the pre-brewing.  
– If the crema is dark brown to black in  
color on the one side and almost  
white on the other side, the grind  
amount might be too much.  
+ back  
SETTINGS J... ~  
+ CARE ...  
^ Select the User profile, for which you  
would like to set the grind amount.  
+ USER PROFILES  
^ Select "Settings".  
^ Select "Settings".  
SETTINGS  
SETTINGS  
+ LANGUAGE F ...  
+ CLOCK  
GRIND AMOUNT ... ~  
PRE-BREWING ~  
more ~  
+ LANGUAGE F ...  
+ CLOCK  
GRIND AMOUNT ... ~  
PRE-BREWING ~  
more ~  
+ TIMER ...  
+ TIMER ...  
^ Select "Pre-brewing".  
^ Select "Grind amount".  
PRE-BREWING  
The grind amount can be set to  
individual preferences for espresso,  
coffee and cappuccino.  
+ Long  
Normal  
+ Normal  
+ Without  
OK ~  
^ Select the desired beverage.  
The second line shows the currently  
selected pre-brewing option.  
^ Select the center left or right touch  
control to set the grind amount to  
more or less.  
^ Set the desired option and select  
"OK" to save the setting.  
^ Select "OK" to save the setting in the  
User profile.  
^ Select "Clear" until the display shows  
the desired menu.  
25  
Settings  
Temperature  
Rinse automatic  
Five temperatures are available for  
each beverage, three for hot water.  
Maximum is the highest temperature,  
minimum the lowest.  
It is important to flush out any residual  
coffee from the lines when starting to  
use the machine for the day. If "Rinse  
Automatic" is set to "on", the rinsing  
starts automatically once the machine  
is turned on and still cold. The lines are  
rinsed with hot water and in return  
pre-warmed. A message shows in the  
display.  
Not every coffee type allows high  
temperatures. Some types react so  
sensitively that the crema cannot be  
properly built.  
^ Select the User profile, for which you  
would like to set the temperature.  
The machine will also run an automatic  
rinse, before it switches off, if it has  
been used to prepare a drink.  
^ Select "Settings" and then "more".  
The rinse automatic is set to on by  
default.  
SETTINGS  
+ back  
STEAM SYSTEM ~  
LIGHTING ... ~  
more ~  
+ TEMPERATURE  
+ RINSE AUTOMATIC  
To turn rinse automatic off/on  
^ Select "Settings" and then "more".  
^ Select "Temperature".  
SETTINGS  
The temperature can be set individually  
for espresso, coffee, cappuccino and  
hot water.  
+ back  
STEAM SYSTEM ~  
LIGHTING ... ~  
more ~  
+ TEMPERATURE  
+ RINSE AUTOMATIC  
^ Select the desired beverage.  
^ Select "Rinse automatic".  
^ Each beverage shows the currently  
selected temperature.  
RINSE AUTOMATIC  
On  
^ Select the respective touch control  
until the desired temperature is  
highlighted.  
+ Off  
+ On  
OK ~  
^ Select "OK".  
The second line shows if the rinse  
automatic is turned on or off.  
^ Select "On" or "Off" and then "OK" to  
save the setting.  
It is recommended to set this option to  
"On" so that the rinse process cannot  
be forgotten.  
26  
Settings  
Steam system  
Lighting  
The appliance has two heating  
Lighting sets the type of light used  
when the appliance is turned on. The  
lighting can be turned on/off  
systems. They allow for independent  
preparation of froth/cappuccino or  
espresso/coffee. The second heating  
system can be turned off to save  
energy during the heating phase e.g. if  
froth is not prepared very often.  
automatically or dimmed to the desired  
brightness. The dimming functions can  
be set independently for the upper or  
lower lighting.  
When the steam system is turned off  
and froth or cappuccino is selected,  
the unit must heat up first to produce  
steam.  
,Caution! Do not look directly or  
with an optical instrument into the  
lighting. Laser!  
As long as the coffee system was  
not completely turned off, the steam  
system is on.  
To change the lighting  
^ Select "Settings" and then "more".  
^ Select "Lighting".  
The steam system is turned on by  
default.  
^ Select "On during use" or "Dimming".  
On during use  
To turn the steam system off  
^ Select "Settings".  
On: The lighting turns on and off when  
the unit is turned on and off.  
^ Select "Steam system".  
Off: The lighting stays turned off.  
The second line shows if the steam  
system is turned on or off.  
Dimming  
^ Select "On" or "Off" and then "OK" to  
save the setting.  
The brightness of the upper and lower  
lighting can be set independently of  
each other.  
^ Select "Top" or "Bottom".  
^ Set the brightness by selecting the  
center touch control to the left or  
right.  
^ Select "OK" to save the selection.  
^ Select "Clear" to get back to  
"Settings".  
27  
Settings  
Total no. coffees  
System Lock  
^ Select "Total no. coffees" to check the The coffee system can be locked so  
number of previously dispensed  
that it cannot be used by children or  
those not familiar with the operating  
instructions.  
espresso, coffee and cappuccino.  
After a few seconds the display  
switches back to the "Settings" menu or To activate the System Lock, it must be  
touch "OK".  
set in the settings.  
^ Select "Settings" and then select  
"more" twice.  
^ Select "System Lock".  
The second line shows if the System  
Lock is currently activated or not.  
^ Select "On" and confirm with "OK".  
If "Off" is selected, the unit cannot be  
locked (safety measure).  
^ Turn the appliance off with the  
"On/Off" touch control.  
^ Select the touch control next to W.  
SYSTEM LOCK  
Off  
+ Off  
+ On  
OK ~  
^ Select "On" and then "OK".  
The appliance is now locked and will  
not operate. The display shows a  
locked padlock X.  
Unlocking the coffee system  
^ Select the X symbol.  
^ Select "Off" and then "OK".  
The appliance is now unlocked and  
ready for use.  
28  
Settings  
Water hardness  
To set the correct water hardness:  
The hardness of the water used in the  
coffee system must be determined and  
programmed into the appliance. The  
water hardness will determine how  
frequently the unit must be descaled to  
maintain the coffee system properly.  
The machine monitors the volume of  
water passing through it in conjunction  
with the hardness of the water and will  
indicate when descaling is necessary.  
Your local water authority can tell you  
the hardness of your tap water or you  
can measure it yourself using the  
enclosed test strip.  
+ back  
SETTINGS J... ~  
+ CARE ...  
+ USER PROFILES  
^ Select "Settings" and then "more"  
twice.  
^ Select "Water hardness".  
^ Select the center touch control to set  
the water hardness harder (right) or  
softer (left).  
^ Select "OK" to save the selection.  
^ Dip the test strip in the water for  
1 second and shake off any  
remaining water. The result is visible  
in about 1 minute.  
If the water hardness is greater than  
40 gr/gal, the water must be  
descaled more often than displayed.  
Calcium will build up faster than at a  
lower water hardness and may  
damage the machine.  
29  
Settings  
User profiles  
Creating a user profile  
Up to 10 different user profiles can be  
entered to accommodate different  
tastes i.e. different grind amounts,  
temperature, pre-brewing, portion  
sizes.  
^ Select "Settings" and then "more"  
twice.  
^ Select "User profiles".  
The upper display line shows which  
user profile is currently set, if different  
profiles were already created.  
The "Standard" profile has standard  
settings.  
^ Select "Creating".  
^ Select the center left or right touch  
control to select a letter.  
^ Touch "Select".  
^ Repeat the step until the desired  
name is spelled out.  
To delete a letter:  
^ Select "Backspace". The last letter  
will be deleted.  
To save a name:  
^ Select "OK". The display shows the  
typed name.  
The display shows more selections:  
"Change name", "Delete", "Change"  
Not saving a name:  
^ Select the "Clear" touch control.  
30  
Settings  
Change name  
Change  
^ If you would like to change a name,  
touch "Change name" and then the  
touch control next to the name to be  
changed.  
The appliance can be set so that it  
changes back automatically to the  
standard profile or that the once set  
user profile is maintained.  
^ Type in the name as described in  
"Creating a user profile" and select  
"OK".  
^ Select "Change".  
^ Select from:  
Never: The unit keeps the once  
selected user profile until another user  
profile is selected.  
^ Select "Clear" to go back to the  
previous screen.  
At turning on: Every time the coffee  
maker is turned on, it selects  
automatically the standard user profile,  
regardless which user profile was last  
selected.  
Delete  
To delete the user profile completely  
^ Select "Delete".  
^ Select the touch control next to the  
name to be deleted.  
After servings: After each dispensing  
of a drink the unit switches  
automatically back to the standard  
profile.  
^ Select "Yes" if you are sure you would  
like to delete the selected name.  
The selected name will be deleted from  
the list.  
Selecting a user profile  
^ Select "User profile - Standard" and  
then the desired profile.  
^ Select "OK".  
The "Standard" profile has standard  
settings.  
31  
Settings  
Display  
Tone options  
The display contrast and brightness  
can be adjusted.  
A tone can be selected to confirm the  
selection of a touch control.  
^ Select "Settings" and then select  
"more" three times.  
^ Select "Settings" and then "more"  
three times.  
SETTINGS  
SETTINGS  
+ back  
PLUMBED ... ~  
RESET ~  
+ back  
PLUMBED ... ~  
+ DISPLAY  
+ TONE OPTIONS  
+ DISPLAY  
+ TONE OPTIONS  
RESET ~  
^ Select "Display".  
^ Select "Tone options".  
^ Select "Brightness" or "Contrast" and  
then the setting. The higher the  
number the higher the contrast or  
brightness.  
To turn the tone on or off  
^ Select "Keypad tone" until the desired  
option is highlighted.  
^ Select "OK" to save the selection.  
If the keypad tones are turned on, the  
volume can be adjusted. The higher the  
number the louder the tone.  
^ Confirm the selection with "OK".  
Volume  
^ Select "Volume" until the desired  
volume of the keypad tone is  
highlighted.  
32  
Settings  
Plumbed  
Reset  
This unit is designed for operation with  
a permanent tap water connection but  
can be converted from water line to  
To select the factory defaults select in  
the submenu to "Reset all" (all settings  
back to default: timer, rinse automatic,  
water tank use. To do that the plumbed steam system, lighting, System Lock,  
water line connection can be turned on water hardness, display, last selected  
or off. When the unit is set to on, it uses coffee type and all standard profile  
the water line. The water tank is  
automatically filled.  
settings), or the "User profiles".  
If you select one of these options  
When the unit is set to off, the water  
tank is used and must be filled  
manually with fresh tap water.  
^ Select "Yes" to reset to the default  
settings or "No" to keep the selected  
settings.  
^ Select "Settings" then "More" three  
times.  
SETTINGS  
+ back  
PLUMBED ... ~  
+ DISPLAY  
+ TONE OPTIONS  
RESET ~  
^ Select "Plumbed".  
^ Select "On" or "Off". The second line  
shows the current setting.  
^ Confirm with "OK".  
33  
Setting the serving sizes  
The flavor of the coffee depends on the Cappuccino is a combination of milk  
coffee and quantity of water used. To  
ensure the machine uses exactly the  
amount of water to suit your taste and  
your cups, there is a choice of two  
serving sizes for espresso/coffee. The  
fill height can be programmed.  
froth and espresso. When preparing  
milk froth the froth-time can be  
individually set. The amount of  
espresso can be set to approx.  
30 - 125 ml.  
^ Set the desired cup size under the  
froth dispenser first.  
Espresso serving size  
approx. 30 - 125 ml.  
^ To set the amount of froth, press and  
hold "Cappuccino" until the display  
shows "Serving setting".  
Coffee serving size  
approx. 30 - 250 ml.  
Hot water serving size  
^ Select "OK" once steam and froth are  
dispensed to your desire. The froth  
time has been set.  
approx. 30 - 250 ml.  
^ Set the desired cup size under the  
coffee dispenser.  
^ You will then be prompted to move  
the coffee cup from under the froth  
dispenser to the coffee dispenser.  
^ Select the drink you would like to  
program. Press and hold the touch  
control until "Serving setting" is  
displayed under the drink type.  
^ Press and hold "OK" until the display  
shows "Serving setting".  
^ Release the touch control.  
^ Release the touch control.  
^ Select "OK" once the cup is filled to  
your desire.  
^ Select "OK" once the cup is filled to  
your desire.  
The programmed amount will be dispensed every time the drink is made.  
The water flow stops automatically when it reaches the maximum amount  
possible. The maximum filling quantity will then be saved for the drink.  
34  
Cleaning and Care  
Allow the coffee system to cool  
before cleaning. Danger of burns!  
+ back  
SETTINGS J... ~  
+ CARE ...  
Do not clean the unit with a steam  
cleaner. Never use cleaners  
containing chlorides, sand, soda or  
scouring agents. These will damage  
the surface.  
+ USER PROFILES  
^ In the main menu touch "more" until  
"Care" shows. Select "Care".  
^ Select "System rinse".  
^ Select "OK".  
To avoid mold of coffee waste, clean  
the unit regularly.  
Hot water will flow through and clean  
the brew unit, hot water and coffee  
dispensers.  
All parts can be cleaned in the  
dishwasher, except the brew unit and  
the bean container. When the parts are  
cleaned in the dishwasher they might  
get discolored by food residues such  
as tomatoes.  
^ When finished select "OK", then  
"Clear" to go back to the main menu.  
See the "Maintenance log" at the end of  
this manual.  
Rinse  
If you do not wish to rinse the lines  
automatically, they have to be flushed  
manually. Rinse them twice daily, once  
before using the machine and before  
turning it off for the day.  
35  
Cleaning and Care  
Water tank  
Waste unit  
If the unit is not plumbed, empty the  
water tank daily and refill before  
The display shows a message to empty  
the waste unit. Clean the waste unit  
preparing the first drink with fresh, cold daily. Coffee waste can mold if there is  
tap water.  
water in the waste unit from the rinse  
process.  
Check if the valve is clean. If the  
valve has residues on it, the water  
tank will not connect properly and  
might leak.  
Line the waste unit with a paper towel  
to make for easier cleaning.  
^ Pull the waste unit out.  
^ Wash the waste container in the  
dishwasher or by hand with hot water  
and liquid dish soap and dry with a  
soft cloth.  
^ Clean the niche of the waste unit in  
the machine.  
^ Push the waste unit completely into  
the machine.  
^ Clean the niche of the water tank.  
^ Remove the water inlet connection  
from the lid of the water tank, clean  
thoroughly.  
36  
Cleaning and Care  
Drip tray  
^ Wash the drip tray in the dishwasher  
or by hand with hot water and liquid  
dish soap, then dry with a soft cloth.  
The trip tray contains a sensor which  
causes the display to show when the  
tray is full and needs to be emptied.  
Clean the drip tray daily.  
Take care that the metal contacts at  
the back of the drip tray are clean  
and dry. If the contacts are soiled or  
wet the unit cannot detect when the  
drip tray is full and needs to be  
emptied.  
Remove the drip tray after the final  
rinse when no more water runs from  
the lines.  
^ Open the door and pull the drip tray  
out.  
The drip tray contains a grid to avoid  
spilling during transport.  
^ Push the drip tray with grid along the  
right edge all way in the machine.  
^ Close the door.  
37  
Cleaning and Care  
Drip catch with metal insert  
Bean container  
The bean container must be cleaned  
by hand with hot water and liquid  
dish soap.  
^ Pull the bean container out and push  
the lid back.  
^ Wash the bean container by hand  
with hot water and liquid dish soap,  
then dry with a soft cloth.  
^ Take out and clean the drip catch  
and metal plate.  
^ Push the lid back and reinsert the  
bean container into the machine.  
38  
Cleaning and Care  
Coffee dispenser connector  
Interior and door  
^ Once all movable parts are removed  
clean the interior with a solution of hot  
water and liquid dish soap.  
Dry ground coffee can be vacuumed.  
A connector between the brew unit and  
coffee dispenser is located on the inner  
door.  
^ Gently clean the connector regularly  
with a damp cloth without removing  
the lubricant for the gasket.  
^ The lower part of the inner door has a  
drip tray. Clean the drip tray.  
^ Lubricate the gasket once a month  
with the supplied silicone grease.  
39  
Cleaning and Care  
Brew unit  
Manually clean the brew unit  
monthly. The movable parts are  
lubricated and the gaskets will get  
damaged in the dishwasher.  
^ Take out the water tank, waste unit  
and the cover for the ground coffee  
funnel.  
^ Rub off any coffee residue from the  
filters with a sponge. One filter is in  
the funnel, a, the second is to the  
left of the funnel, b.  
^ Dry the funnel, a, to prevent ground  
coffee from sticking.  
^ Clean the interior and remove coffee  
residues. Dry coffee grounds can be  
vacuumed.  
^ Press the light colored button on the  
brew unit handle, a, and turn the  
handle to the left, b.  
^ Push the brew unit in the track  
straight into the appliance.  
^ Press the brew unit catch, c,  
downwards and pull the brew unit  
out.  
The brew unit is not in the correct  
position if it is hard to pull out. See  
"Frequently asked questions".  
^ Clean the brew unit under running  
warm water. Do not use soap.  
^ Press the light colored button on the  
brew unit handle, a, and turn the  
handle to the right, b.  
Leave the handle in position or the  
brew unit cannot be inserted  
properly.  
40  
Cleaning and Care  
Cleaning/Degreasing the brew unit  
^ Set a 1 quart container under the  
coffee dispenser.  
Depending on the fat content of the  
coffee, the brew unit can clog. Clean  
the brew unit approx. every 200 cups  
with the enclosed detergent tablets.  
They are specially developed for the  
coffee maker to optimize the  
The interior is also rinsed, therefore the  
drip tray must be emptied.  
When the display shows:  
Please drop the cleaning tablet in the  
funnel for ground coffee  
degreasing. The cleaning tablets can  
be purchased from Miele.  
^ Take out the funnel cover and open  
the funnel lid.  
As a reminder the display shows  
"Cleaning must be started" after  
200 cups and then until the machine  
is cleaned. The cleaning process  
takes about 6 minutes.  
^ Select "Care".  
^ Select "Cleaning" and then "OK".  
The display guides you through the  
cleaning process. Please follow the  
single steps.  
^ Insert the cleaning tablet in the  
funnel.  
^ Close the lid, reinsert the cover and  
close the door.  
^ Select "OK".  
Follow the display messages.  
When the display shows:  
Process finished. Please confirm.  
The brew unit is cleaned and rinsed.  
^ Select "OK" and then "Clear" to go  
back to the main menu.  
41  
Cleaning and Care  
Froth dispenser/Intake hose  
Clean the froth dispenser after each  
use, otherwise they may become  
blocked with dried milk and hard to  
clean.  
Rinsing does not replace cleaning in  
the dishwasher.  
^ Select "Care".  
^ Pull all pieces apart. Remove the  
piece with the gaskets by turning and  
pulling it apart.  
^ Select "System rinse".  
^ Set a glass with water under the  
intake hose and select "OK".  
^ Insert the pieces in the dishwasher  
and then lubricate the gaskets with  
the supplied silicone grease.  
The intake hose takes in the water and  
rinses it.  
Take care that the small holes of the  
single pieces are not clogged (see  
arrow).  
Cleaning in the dishwasher  
To clean the froth dispenser in the  
dishwasher, take the parts from the  
machine. Regular cleaning in the  
dishwasher is important, so that the  
froth dispenser does not clog over time,  
when milk is not removed during  
rinsing.  
Pinch the soft parts to loosen the  
soiling, then blow them out.  
Do not use a needle to remove  
residues, the parts may get  
damaged.  
^ Turn the cover above the spout to the  
left, a.  
^ Pull the froth dispenser out of the  
machine, b, holding it by the spout  
and the intake hose.  
42  
Cleaning and Care  
^ Reassemble the parts as shown.  
Take care that the raised parts (see  
arrow) point downwards and,  
^ Push the froth dispenser into the  
machine from underneath, a, and  
turn the cover above the spout to the  
right, b.  
Do not use the machine without the  
froth dispenser installed.  
Steam will spit uncontrollably.  
Danger of scalding and machine  
damage.  
^ that the marks are lined up.  
43  
Cleaning and Care  
Exterior  
Stainless steel surfaces  
The front of the appliance can be  
Stainless steel surfaces can be cleaned  
cleaned with a sponge and a solution of using a non-abrasive stainless steel  
warm water and non abrasive liquid  
dish soap. Dry with a soft cloth.  
cleaner (available from Miele).  
To help prevent soiling, a conditioner  
for stainless steel can also be used.  
Apply sparingly and with even  
pressure.  
Only use a slightly damp sponge  
when cleaning the controls. Water  
could penetrate into the electronics  
and cause damage.  
Stainless steel colored controls  
Clean the buttons and knobs with a  
sponge and a solution of warm  
water and liquid dish soap. These  
controls may become discolored or  
damaged if not cleaned regularly.  
Do not use a stainless steel cleaner  
on the knobs or buttons. Clean  
immediately after use.  
Abrasive cleaning agents, glass  
cleaning agents, all-purpose  
cleaners, thinner or ammonium  
cleaners should not be used on the  
machine. They will damage the  
surface.  
Wipe any spills from descaling  
immediately!  
44  
Descaling the appliance  
The coffee system must be descaled  
regularly. The appliance will display a  
reminder message to descale and will  
eventually lock if not descaled.  
Descaling  
For descaling purposes the machine  
automatically switches from the  
plumbed function to the water  
container.  
The display will show "Please descale  
the coffee system. Remaining numbers  
of servings: 50". This message will now  
appear after each preparation. If the  
counter has elapsed to 0, the appliance  
will be locked.  
^ To descale the unit before it is heated  
up, select "Descaling" in the main  
menu.  
^ To start the descaling process before  
prompted by the machine (e.g.  
because of very hard water), select  
"Care".  
Select "Descaling" to start the descaling  
immediately. The descaling takes about  
20 minutes. If you want to continue at a  
later point in time, turn the unit off. The  
appliance can only be used again once  
descaling is performed.  
^ Select "Descaling" and then "OK".  
The display prompts the user through  
the single steps of the descaling  
process. Follow the prompts.  
Only use the enclosed descaling  
tablets for descaling. They are  
specially developed for the coffee  
system to optimize the descaling.  
The descaling tablets can be  
purchased from Miele.  
If the descaling is started while the  
machine is still hot, the appliance  
will cool down for 10 minutes before  
the descaling begins.  
Other agents may damage the  
machine and affect the taste of  
coffee and hot water.  
The descaling process cannot be  
canceled once "OK" is selected. The  
process now needs to be  
The machine could also be  
damaged.  
completed. This is a safety feature to  
ensure the process will be  
completed. It is important for best  
results and the longevity of the  
machine.  
Use the supplied descaling funnel to  
protect the appliance front from the  
descaling agent. Clean up any  
descaling spills immediately to  
avoid damage to the appliance  
front. Thoroughly clean the water  
tank and the drip tray of descaling  
residues.  
45  
Descaling the appliance  
^ The display will prompt you through  
the next steps:  
^ Please fill the water tank with tap  
water to the descaling mark and  
reinsert it: Take the water tank out,  
rinse out any descaling residues  
thoroughly with water. Fill with fresh  
water to the k mark.  
– to fill the descaling agent into the  
water tank  
– take the water tank out  
– fill the water tank with fresh lukewarm During rinsing water runs from the  
tap water to the mark k. If not filled  
to the mark, the descaling will be  
canceled prematurely and  
incomplete  
dispensers. When the display shows  
Please empty the drip tray: Empty the  
drip tray. Since the machine is also  
rinsed inside, the drip tray needs to be  
emptied to continue rinsing.  
Dissolve two of the enclosed  
descaling tablets in the water. Close  
the water tank and insert into  
position.  
When the display shows: Process  
finished: Descaling is complete. Follow  
the prompts in the display. The  
appliance is rinsed a final time.  
^ Set the descaling funnels under the  
coffee dispensers. Set the funnel in  
the holes of the drip tray so the  
dispensed liquids are guided in the  
drip tray.  
During the descaling process the  
descaling solution will flow from the hot  
water and coffee dispensers. The  
machine rests briefly to allow the  
solution to take affect before  
dispensing again.  
46  
Frequently asked questions  
Repairs to electrical appliances should only be carried out by a suitably  
qualified person in accordance with local and national safety regulations.  
Repairs and other work by unqualified persons could be dangerous. The  
manufacturer cannot be held responsible for unauthorized work.  
Machine Problems  
The light does not illuminate when the appliance is turned on.  
– Is the unit locked?  
– Is the lighting turned off?  
– See "Settings - Lighting".  
If not, the light bulb has burnt out.  
Contact Miele's Technical Service  
Department.  
The heating phase takes a long time.  
When the door is opened during the Keep the door closed during the heating  
heating up phase, e.g. to fill the  
water tank, the heating element turns  
off. The unit heats only with the door  
closed.  
phase.  
The light turns off suddenly.  
The light turns off automatically when the machine has not been used for  
10 minutes.  
The display messages are difficult to read.  
The contrast or brightness of the  
displays are too low / high.  
Adjust the display contrast / brightness.  
See "Settings - Display".  
The display remains dark.  
The unit has no power.  
– The main switch is turned off.  
– The machine is not plugged in.  
– Check that the fuse had not blown or is  
defective. If the fuse has blown contact  
Miele's Technical Service Department.  
47  
Frequently asked questions  
The unit suddenly turns off.  
– Is the machine programmed to  
switch off after a programmed  
time?  
– The machine goes into standby mode  
when not used for a programmed time.  
See "Settings - Timer - Turning off after".  
– The water temperature could be to – The unit is locked until the water has  
high. cooled.  
– There could be pebbles within the – Call Miele's Technical Service  
coffee beans. The unit shuts off  
after 20 secs. to avoid damages.  
Department.  
– Is the machine plugged in?  
– Plug in the machine.  
The door cannot be closed.  
Check if all containers are properly inserted.  
The door is hard to open and close, and the gasket of the connector is  
pulled off.  
Adjust the door with the door hinges. See "Installation - Adjusting the door  
hinges".  
The gasket of the coffee dispenser connector is damaged and leaking.  
– The gasket is worn.  
– Change the gasket with a new one  
(supplied).  
– Check the door. Is the alignment  
off from damage to the gasket?  
– Adjust the door with the door hinges.  
See "Installation - Adjusting the door  
hinges".  
The grind control lever will not move.  
Close the unit and prepare a coffee/espresso. The grind grade can now be reset.  
The brew unit cannot be taken out.  
The brew unit is not in the correct  
position.  
Close the door and turn the appliance on.  
The brew unit will position itself into the  
correct position.  
The cover of the ground coffee funnel cannot be pushed in properly.  
Close the lid of the ground coffee funnel.  
48  
Frequently asked questions  
Preparing / dispensing problems  
No water, steam or milk is dispensed from the froth dispenser.  
– The water tank is not correctly  
inserted.  
– Take out the water tank and reinsert it.  
– Clean the froth dispenser as described  
in "Cleaning and Care - Froth  
dispenser/Intake hose".  
– The dispenser is clogged.  
The grinding sounds louder than usual.  
There could be pebbles within the  
coffee beans.  
Turn off the unit immediately.  
Contact the Miele's Tech. Service.  
The grinding is quieter than usual.  
The coffee bean container is empty. Wait until no sound is heard and refill the  
The respective message appears in coffee bean container.  
the display.  
The coffee/espresso flows too fast into the cup.  
The grind control is set too coarse.  
Set the grind control to a finer grind.  
The coffee/espresso flows too slow into the cup.  
The grind control is set too fine.  
Set the grind control to a coarser grind.  
The coffee/espresso is not hot enough.  
– Were the supply lines pre-heated? – The smaller the cup, the more  
important it is to pre-heat.  
– The temperature is set too low.  
– Check on what temperature range the  
coffee type is set.  
– Check if the brew unit is clogged. – Clean the brew unit.  
No drink is prepared although the beans were grinded and enough water is  
in the container.  
– The grind control is set to the  
finest or the grind amount is set to  
the maximum.  
– Set the grind control or the grind  
amount to a different position.  
– The process is timed, the process  
might need so long, there is no  
time for brewing any more.  
49  
Frequently asked questions  
The steam heating system is turned off but steam can still dispensed.  
Steam can be dispensed as long as the steam heating system is heated. Once it  
has cooled, steam can only be dispensed once the steam system has heated.  
The coffee dispensing is interrupted.  
The water tank is empty.  
If the unit is plumbed, check the water line  
and plumbing.  
If the unit is used with the water tank, refill  
the water tank with fresh cold tap water.  
You will be asked whether you would like  
the coffee dispensing to continue after the  
water tank has been filled. If you do not  
confirm with "OK" within 5 minutes the  
coffee preparation will be cancelled.  
Instead of coffee only water is dispensed.  
– The beans may have gotten stuck. – Pull the bean container out and push it  
back in.  
– The ground coffee funnel cover  
was opened and closed and a  
preparation with ground coffee  
was selected but no ground coffee  
was inserted.  
The coffee system switches  
automatically back to beans use  
after the preparation.  
The drip tray is empty but a message to empty it is displayed.  
– The metal contacts are soiled or  
wet.  
– Clean and dry the contacts.  
– Check if the drip tray is inserted  
correctly.  
– Insert the drip tray as described in  
"Cleaning and Care - Drip tray".  
– Turn the machine off and on again with  
the main switch.  
– If the message still appears contact  
Technical Service.  
50  
Frequently asked questions  
The machine does not rinse when turned on although the automatic rinse  
feature is set to "On".  
When the machine is still at a temperature of about 140°F (60°C). The machine  
will not rinse when it's too hot.  
The water dispensing stops when programming the serving size.  
– There was not enough water in the – Fill the water tank before programming  
tank (if the unit is not plumbed).  
The dispensed water amount will  
not be saved.  
the serving size.  
– If the maximum water amount is  
dispensed, the water flow stops  
automatically. The maximum water  
amount is saved.  
Water is in the waste unit.  
This is not a fault.  
This is residual water from the cleaning  
process.  
"Coffee water" is in the waste unit.  
If the grind control is set to very fine, If the grind control is not set to very fine,  
there might be coffee water in the contact Technical Service.  
waste unit.  
The descaling process was started accidently.  
The descaling process cannot be canceled once it is started. The process  
needs now to be completed. This is a safety feature to ensure the process will be  
completed. It is important for best results and the longevity of the machine.  
The preheating time is increased, the water flow amount is not correct and  
the unit performs less?  
The machine needs to be descaled. See "Descaling the appliance".  
No water flows from the spouts.  
The filters in the brew unit are  
clogged.  
Rub any residue off the filters with a  
sponge.  
51  
Frequently asked questions  
The brew unit or waste unit could not be pulled from the machine.  
– The brew unit is not in the basic  
position.  
– Close the door. The brew unit  
automatically gets into the basic  
position.  
– The door was opened during  
grinding or brewing.  
No crema has formed or it is "different".  
– Check if the grind control is set too – The coffee is not fresh enough.  
coarse or too fine.  
– The coffee is unsuitable for use in this  
– Check what temperature range the  
coffee type is set. If the  
machine. See "Filling the beans  
container".  
temperature is too high, there are  
black areas in the crema.  
– The coffee dispensers are set too high.  
Too much crema has formed and is above the coffee dispensers.  
Some coffee types produce too  
much crema when the coffee /  
espresso temperature is set to the  
maximum and the amount of ground  
coffee is too much.  
Lower the temperature and amount of  
ground coffee.  
The milk froth does not flow but "spits".  
Before using for the first time the water lines need to be filled. See "Making  
coffee - Cappuccino and milk froth".  
When preparing milk froth for the first time, the milk is spit from the mug.  
The door was opened during the  
Keep the door closed during the heating  
heating phase. High steam pressure phase.  
has built making the steam  
dispensed too strong when the valve  
is opened.  
When preparing milk froth the preparation starts, stops then starts again.  
This is not a fault. The start and stop action aids the machine in preparing the  
best froth possible.  
You hear water gurgle or rushing.  
The water tank has automatically filled.  
52  
Frequently asked questions  
"F" messages  
F 10 or F 17  
No water is dispensed.  
– The water tank is not inserted properly.  
Take it out and reinsert correctly.  
– The water tank was not filled correctly  
during the descaling process. Fill the  
water tank up to the correct mark.  
– After fixing the fault, the machine turns  
off then on again. Start the desired  
preparation again.  
– If the message still appears contact  
Technical Service.  
F 73 or "Check brew unit"  
The brew unit is clogged and cannot – Select "Clear".  
reset to the correct position.  
– Take out and clean the brew unit. See  
"Cleaning and Care - Brew unit".  
– Reinsert the brew unit and close the  
door.  
– If the message still shows contact  
Technical Service.  
F 94  
The plumbed water intake is faulty.  
– Check for kinks in the water intake hose  
and open the water supply all the way.  
– If the fault is still displayed, call  
Technical Service.  
The message "Too much ground coffee" appears in the display.  
If too much ground coffee passes  
through the coffee chute the machine  
is unable to process it so it can be  
emptied into the waste container.  
– Select "OK".  
The machine is now ready for use.  
53  
After sales service  
In the event of a fault which you cannot MieleCare  
easily fix yourself, please contact the  
MieleCare, our Extended Service  
Miele Technical Service Department at  
the contact information on the back of  
this booklet.  
Contract program, gives you the  
assurance of knowing that your  
appliance investment is covered by  
5 years of worry free ownership.  
When contacting the Technical Service  
Department, please quote the model  
and serial number of your appliance  
given on the data plate inside the  
appliance.  
MieleCare is the only Extended Service  
Contract in the industry that guarantees  
repairs by a Miele Authorized Service  
Provider using genuine Miele parts.  
Only genuine Miele parts installed by  
factory trained professionals can  
guarantee the safety, reliability, and  
longevity of your Miele appliance.  
Please note that unless expressly  
approved in writing by Miele’s Service  
department, Extended Service  
Contracts offered by other providers for  
Miele products will not be recognized  
by Miele. Our goal is to prevent  
unauthorized (and untrained) service  
personnel from working on your Miele  
products, possibly doing further  
damage to them, you and/or your  
home.  
To learn more about MieleCare  
Extended Service Contracts, please  
contact your appliance dealer or visit  
us online at:  
54  
Installation instructions  
Caring for the environment  
Disposal of packing material  
Disposal of an old appliance  
The cardboard box and packing  
materials protect the appliance during  
shipping. They have been designed to  
be biodegradable and recyclable.  
Please recycle.  
Old appliances may contain materials  
that can be recycled. Please contact  
your local recycling authority about the  
possibility of recycling these materials.  
Ensure that the appliance presents no  
danger to children while being stored  
for disposal. Before discarding an old  
appliance, unplug it from the outlet, cut  
off its power cord and remove any  
doors to prevent hazards.  
Ensure that any plastic wrappings,  
bags, etc. are disposed of safely and  
kept out of the reach of children.  
Danger of suffocation!  
56  
Plumbing  
Connection to the water  
The machine must be connected to  
the water supply in accordance with  
local and national regulations.  
The water being used should have  
the drinking water standards of the  
respective country where the  
machine is used.  
supply  
^ Disconnect the machine from the  
electrical supply.  
^ Remove the water connection cover  
at the lower rear side of the coffee  
machine.  
^ Screw the supplied brass  
– All units and systems used to deliver  
the water to the coffee system must  
conform with the requirements of the  
respective country.  
compression fitting, with the ¾" end,  
tightly onto the water connector of the  
coffee machine. (Tighten the  
compression fitting by hand, do not  
use a tool.) The fitting includes an  
opening for standard ¼" piping.  
– The machine is designed to be  
plumbed to a cold water connection.  
– The machine can be connected  
without a non-return valve.  
– The on-site water line must have a  
water valve to turn the water off if  
needed. If not present, have a water  
valve installed by a licensed  
plumber.  
^ Connect the compression fitting to  
the water supply.  
– The water faucet must be accessible  
after installation.  
^ Check for leaks.  
– Water pressure on-site:  
Minimum: 14.5 psi  
Maximum: 145 psi, if higher, install a  
pressure reduction valve.  
– Suitable 1/4" tubing or copper piping  
must be supplied for plumbing.  
– To ensure the best coffee quality, the  
maximum length of the tubing or  
copper pipe should not exceed  
4 ft. 11" (1.5 m). If too much water  
remains in the tubing the coffee  
quality could be affected.  
57  
Electrical connection  
Important  
Ensure that power is not supplied to  
the machine while installation or  
maintenance work is performed.  
The coffee system comes equipped  
with a 6 ft (1.8 m) power cord with a  
NEMA 5-15P molded plug for  
connection to a 120 V, 15 A, 60 Hz  
power supply.  
All electrical work should be  
performed by a qualified electrician  
in strict accordance with national  
and local safety regulations.  
Installation, repairs and other work  
by unqualified persons could be  
dangerous.  
The manufacturer cannot be held  
responsible for unauthorized work.  
Verify that the voltage, load and circuit  
rating information found on the data  
plate match the household electrical  
supply before installing the coffee  
system.  
If there is any question concerning the  
electrical connection of this appliance  
to your power supply, please consult a  
licensed electrician or contact Miele’s  
Technical Service Department. See  
back page for contact information.  
WARNING:  
THIS APPLIANCE MUST BE  
GROUNDED  
58  
Installation  
Installation options  
The coffee system is designed to be built into cabinetry.  
A combination with other Miele built in appliances is possible. If the machine is  
installed in combination with other appliances, it should be installed with a  
protective base between the appliance and the unit (exception: installation with a  
built-in plate warmer).  
A special display cabinet is also available from your dealer or Miele, as an  
installation option.  
59  
Installation  
Installation  
^ If your cabinet has 3/4" (19 mm) side  
walls, drill four holes for the  
mounting.  
Make sure power is not supplied to  
the appliance while installation or  
maintenance work is performed.  
Disconnect the power supply to the  
work area by unplugging the unit,  
tripping the circuit breaker or  
removing the fuse. The coffee  
system must be installed into  
cabinetry before being used.  
^ Center the unit and turn the screws a  
little bit in and then out again.  
^ Take the unit out of the niche and drill  
four holes at the screw markings  
(1/16" [2 mm], diameter 3/16"  
[4.5 mm]).  
^ Connect the appliance to a cold  
water supply.  
^ Plug the appliance into the electrical  
outlet.  
^ Push the appliance into the niche.  
^ Open the door and partially tighten  
the screws.  
^ Unscrew the height adjustable feet  
on the underside of the machine  
about 1/16" (2 mm).  
^ Push the appliance all the way back  
into the cabinet and center it. If  
necessary level the unit with the four  
height adjustable feet.  
The feet can be turned out up to 3/8"  
(10 mm).  
^ Carefully turn the lower screws, a, to  
center the machine.  
^ To secure the appliance in the  
cabinet, tighten the upper screws, b,  
by hand. Do not use an electric  
screwdriver.  
60  
Installation  
Adjusting the door hinges  
The door hinges can be adjusted if the  
door cannot be opened easily.  
^ To adjust the door sideways, a, turn  
screw a.  
^ To adjust the door to the front or  
back, b, turn screw b.  
61  
62  
63  
Alteration rights reserved / 4507  
with convertible water connection  
CVA 4075  
M.-Nr. 07 194 220 / 01  
For the most updated manual see the Miele web site.  

LG Electronics LG Lifes Good Cell Phone LG 8550 User Manual
Jura Capresso 601 User Manual
Insignia NS PRCL01 User Manual
HoMedics Clock Radio HMDX C20 User Manual
Hamilton Beach BrewStation Deluxe 47494 User Manual
Fujitsu MHS2020AT User Manual
Fujitsu Computer Drive MHV2080AS User Manual
Ericsson R310s User Manual
Creek Audio CD43 mk 2 User Manual
Black & Decker DCM1350B User Manual