MTT3200 O/M.QXD 2/28/03 9:22 AM Page 11
NOSTALGIC STEREO SYSTEM WITH
CD PLAYER AND AM/FM STEREO
RADIO
MODEL: MTT3200
BEFORE OPERATING THIS PRODUCT, PLEASE READ THESE
INSTRUCTIONS COMPLETELY.
OPERATING INSTRUCTIONS
MTT3200 O/M.QXD 2/28/03 9:22 AM Page 2
SAFETY INSTRUCTIONS
Before using the unit, be sure to read all operating instructions
carefully. Please note that these are general precautions and may not
pertain to your unit. For example, this unit may not have the capability
to be connected to an outdoor antenna.
15. OVERLOADING
Do not overload wall outlets and extension cords as this can result in a
risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
1. READ INSTRUCTIONS
Never push objects of any kind into this product through openings as they
may touch dangerous voltage points or short out parts that could result in
fire or electric shock. Never spill or spray any type of liquid on the product.
17. OUTDOOR ANTENNA GROUNDING
All the safety and operating instructions should be read before the
product is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the product and in the operating instructions should be
adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this product from the wall outlet before cleaning. Do not use
liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. ATTACHMENTS
If an outside antenna is connected to the product, be sure the antenna
system is grounded so as to provide some protection against voltage
surges and built-up static charges. Section 810 of the National Electric
Code, ANSI/NFPA 70, provides information with respect to proper
grounding of the mast and supporting structure, grounding of the lead-
in wire to an antenna discharge product, size of grounding conductors,
location of antenna discharge product, connection to grounding
electrodes, and requirements for grounding electrode.
Do not use attachments not recommended by the product's
manufacturer as they may cause hazards.
7. WATER AND MOISTURE
Do not use this product near water- for example, near a bathtub,
washbowl, kitchen sink, or laundry tub, in a wet basement, or near a
swimming pool.
8. ACCESSORIES
Do not place this product on an unstable cart, stand, tripod, bracket, or
table. The product may fall, causing serious injury and serious damage to
the product. Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the
product. Any mounting of the product should follow the
PORTABLE CART WARNING
(symbol provided by RETAC)
manufacturer’s instructions, and should use a mounting
accessory recommended by the manufacturer.
8A. An appliance and cart combination should be moved
with care. Quick stops, excessive force, and uneven
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
surfaces may cause the appliance and cart
18. SERVICING
combination to overturn.
9. VENTILATION
Do not attempt to service this product yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer
all servicing to qualified service personnel.
Slots and openings in the cabinet and in the back or bottom are
provided for ventilation and to ensure reliable operation of the product
and to protect it from overheating. These openings must not be blocked
or covered. The openings should never be blocked by placing the
product on a bed, sofa, rug, or other similar surface. This product
should never be placed near or over a radiator or heat source. This
product should not be placed in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the
manufacturer's instructions have been adhered to.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician
uses replacement parts specified by the manufacturer or those that
have the same characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks to determine that the
product is in proper operating condition.
10. POWER SOURCES
This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your appliance dealer or local power
company. For products intended to operate from battery power, or
other sources, refer to the operating instructions.
21. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
22. DAMAGE REQUIRING SERVICE
Unplug the product from the wall outlet and refer servicing to qualified
service personnel under the following conditions:
11. GROUNDING OR POLARIZATION
This product is equipped with a polarized alternating-current line plug
(a plug having one blade wider than the other). This plug will fit into the
power outlet only one way. This is a safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the
operating instructions, as an adjustment of other controls may result
in damage and will often require extensive work by a qualified
technician to restore the product to its normal operation.
e. If the product has been dropped or the cabinet has been damaged.
Power-supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience receptacles, and the
point where they exit from the appliance.
f.
When the product exhibits a distinct change in performance - this
indicates a need for service.
13. LIGHTNING
23. HEAT
The product should be situated away from heat sources such as
radiators, heat registers, stoves, or other products (including amplifiers)
that produce heat.
24. NOTE TO CATV SYSTEM INSTALLER
To protect your product from a lightning storm, or when it is left
unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable system. This will prevent
damage to the product due to lightning and power-line surges.
14. POWER LINES
This reminder is provided to call the CATV system installer's attention
to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be
connected to the grounding system of the building, as close to the point
of cable entry as practical.
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or where it
can fall into such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be fatal.
2
MTT3200 O/M.QXD 2/28/03 9:22 AM Page 3
LOCATION OF CONTROLS
1
2
3
4
5 6 7 8 9 1011 12 13
14
15
16 17 18 19 20
21 22
1. VOLUME Control
13. POWER Indicator
14. CD Compartment
15. FM ST Indicator
2. AC Cord (Rear of Unit)
3. AM/FM Dial Scale and Pointer
4. TUNING Control
5. Speaker
16. CD Open/Close Button
17. Speaker
6. SKIP/Search
Button
18. STOP (■) Button
19. Play/Pause Indicator
20. PLAY/PAUSE (Š/ ) Button
21. FUNCTION Switch
22. BAND Switch
7. Program Indicator
8. PROG (Program) Button
9. Display
10. RPT (Repeat) Button
11. Repeat Indicator
12. SKIP/Search
Button
3
MTT3200 O/M.QXD 2/28/03 9:22 AM Page 4
PREPARATION FOR USE
AC Operation
Unwind the AC cord and extend it to its full length. Insert the end of the AC cord into any convenient 110-
120V 60Hz household outlet.
Please note that this unit is equipped with a polarized AC plug which has
one blade wider than the other. This is a safety feature to reduce the
likelihood of electric shock. This polarized AC plug will only fit in a
polarized AC outlet. If you find that you cannot insert this plug into your
outlet, you may have an obsolete non-polarized outlet. Please do not try
to defeat this safety feature by using a non-polarized adapter or by filing
the wider blade to make it fit into your outlet. If this plug does not fit into
your outlet, you should contact a qualified licensed electrician to replace your obsolete outlet.
RADIO OPERATION
TO PLAY THE RADIO
1
2
3
Slide the FUNCTION switch to Slide the BAND switch to select Rotate the TUNING control to
the RADIO position.
AM, FM or FM STEREO. Noise select a station.
present in FM broadcasts can be
reduced by sliding the BAND
switch to FM STEREO position;
the broadcast will then be in
mono.
4
FM STEREO
When the BAND switch is set to the FM STEREO position and a
strong FM stereo station is broadcasting, the FM ST indicator will light.
1
2
ANTENNAS
AM – This unit has a built-in ferrite rod antenna, which provides
adequate reception in most areas. If reception is weak, turn the unit to
improve reception.
Adjust the VOLUME control ■ as
desired. Slide the FUNCTION
switch ■ to the OFF position to
turn the unit off.
FM – If reception is weak, extend the AC cord to its full length. You
may have to vary the direction of the AC cord to find the strongest
signal for each FM station.
4
MTT3200 O/M.QXD 2/28/03 9:22 AM Page 5
COMPACT DISC (CD) OPERATION
TO INSERT AND PLAY A CD (STANDARD CD, CD-R AND CD-RW CAN BE USED)
1
2
3
1
1
2
2
Slide the FUNCTION switch ■ to
the CD position and press the CD
Open/Close button ■. Place a CD
on the center spindle, with the
printed label side facing up. Press
the CD Open/Close button ■ again
to close the CD compartment door.
To play a disc from the beginning, To start from a specific track,
press the PLAY/PAUSE (Š/ )
button. Press the PLAY/PAUSE
(Š/ ) button again to pause
playback; the Play/Pause
indicator will blink.
locate the track using the
SKIP/Search ■ or
button; the unit will automatically
play the track.
■
4
5
6
1
1
2
2
Adjust the VOLUME control as To skip forward or backward To search forward or backward
desired.
through the tracks on the disc, through the tracks, press and hold
press the SKIP/Search
■ or the SKIP/Search
■ or
■
■ button.
button, a chattering noise will be
heard.
7
8
FAQS:
Do I need an adapter to play 3”
singles?
No, simply insert the 3” single into the
groove.
What type of CDs can I play?
CD, CD-Rs and CD-RWs can be used.
When the disc is through playing, When you have finished listening,
it will stop rotating. Press the slide the FUNCTION switch to the
STOP (■) button to stop the disc OFF position.
before it is finished.
NOTES:
• If a disc is inserted incorrectly, dirty, damaged or not present at all, it will not play.
• As each track is played, the track number is shown in the display.
5
MTT3200 O/M.QXD 2/28/03 9:22 AM Page 6
COMPACT DISC (CD) OPERATION (CONTINUED)
TO REPEATEDLY PLAY BACK ONE TRACK
1
2
3
1
1
1
2
2
2
Slide the FUNCTION switch ■ to Select
SKIP/Search
Open/Close button ■. Place a CD button; the unit will automatically unit will play the selected track
a
track using the Press the RPT button ■ once, the
■ or
■
the CD position and press the CD
Repeat indicator will blink and the
play the track.
over and over until the STOP (■)
button ■ is pressed.
on the center spindle, with the
printed label side facing up. Press
the CD Open/Close button ■ again
to close the CD compartment door.
TO REPEATEDLY PLAY BACK ALL TRACKS
1
2
3
1
2
2
1
Slide the FUNCTION switch ■ to Press the RPT button twice, the
Press the PLAY/PAUSE (Š/ )
button ■ to begin playback and
the unit will play the entire disc
over and over until the STOP (■)
button ■ is pressed.
Repeat indicator will light.
the CD position and press the CD
Open/Close button ■. Place a CD
on the center spindle, with the
printed label side facing up. Press
the CD Open/Close button ■ again
to close the CD compartment door.
NOTE:
To stop and cancel Repeat playback, press the STOP (■) button.
6
MTT3200 O/M.QXD 2/28/03 9:22 AM Page 7
COMPACT DISC (CD) OPERATION (CONTINUED)
TO PROGRAM THE MEMORY (UP TO 30 TRACKS)
1
2
3
1
1
2
2
Slide the FUNCTION switch ■ to Press the PROG button; “01” will Use the SKIP/Search
■ or
■ button to select the first
track to be programmed.
appear in the display and the
Program indicator will blink.
the CD position and press the CD
Open/Close button ■. Place a CD
on the center spindle, with the
printed label side facing up. Press
the CD Open/Close button ■ again
to close the CD compartment door.
4
5
6
1
2
Press the PROG button again; the Repeat steps 3 and 4 to program
Press the PLAY/PAUSE (Š/ )
selected track has now been the other desired tracks in button to begin playback; the
programmed and counted as sequence (up to 30 tracks).
program 1.
Program indicator will light and
the tracks will play in the order
programmed.
NOTES:
•
•
•
•
Programming is the ability to preselect the order in which a series of tracks will be played.
Each track may be stored in the program memory as many times as desired (up to 30 tracks).
If you attempt to program in more than 30 tracks, the display will show “Fu” (Full).
As each track is played, its track number will be displayed. You can move forward or backward through
the programmed tracks with the SKIP/Search
or
button.
•
The CD player will stop after all programmed tracks have been played or the STOP (■) button is
pressed.
•
•
To playback the program again, press the PROG button, then press the PLAY/PAUSE (Š/ ) button.
To clear the program memory, press the STOP (■) button while in the Stop mode.
7
MTT3200 O/M.QXD 2/28/03 9:22 AM Page 8
CARE AND MAINTENANCE
Caring for Compact Discs
• Treat the compact disc carefully. Handle the compact disc
only by its edges. Never allow your fingers to come in contact
with the shiny, unprinted side of the compact disc.
• Do not attach adhesive tape, stickers, etc. to the compact
disc label.
• Clean the compact disc periodically with a soft, lint-free, dry
cloth. Never use detergents or abrasive cleaners to clean
the compact disc. If necessary, use a CD cleaning kit.
• If a compact disc skips or gets stuck on a section of the compact disc, it is probably dirty or damaged
(scratched).
• When cleaning the compact disc, wipe in straight lines from the center of the compact disc to the outer
edge of the compact disc. Never wipe in circular motions.
Z
• This unit is designed to play only compact discs bearing the identification logo as shown here.
Other discs may not conform to the CD standard and may not play properly.
• Compact Discs should be stored in their cases after each use to avoid damage.
• Do not expose compact discs to direct sunlight, high humidity, high temperatures, or dust, etc. Prolonged
exposure or extreme temperatures can warp the compact disc.
• Do not stick or write anything on either side of the compact disc. Sharp writing instruments, or the ink may
damage the surface.
Cleaning the unit
• To prevent fire or shock hazard, disconnect your unit from the AC power source when cleaning.
• The finish on your unit may be cleaned with a dust cloth and cared for as other furniture. Use caution
when cleaning and wiping the plastic parts.
• Mild soap and a damp cloth may be used on the front panel.
8
MTT3200 O/M.QXD 2/28/03 9:22 AM Page 9
TROUBLESHOOTING GUIDE
Should this unit exhibit a problem, check the following before seeking service.
Symptom
Radio
Possible Cause
Solution
Noise or sound distorted
on radio broadcasts.
Station not tuned properly for
AM or FM.
Retune the AM or FM broadcast
station.
FM: Wire Antenna is not
properly adjusted.
Fully extend FM Wire Antenna..
AM: Unit is not positioned
correctly.
Rotate unit until best reception is
obtained.
AM or FM, no sound.
FUNCTION switch not set to RADIO.
Volume at minimum.
Set FUNCTION switch to RADIO.
Increase volume.
Compact Disc Player
CD Player will not play.
FUNCTION switch not set to CD.
Set FUNCTION switch to CD.
Insert CD with label side up.
CD is not installed or installed
upside-down.
CD skips while playing.
Disc is dirty or scratched.
Wipe disc with cloth or use
another disc.
General
No sound.
Power cord disconnected.
Connect power cord.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT OUR WEBSITE
AT WWW.MEMOREXELECTRONICS.COM OR CONTACT CUSTOMER SERVICE AT
1-800-919-3647
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED
TO RETURN THIS PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT 1-800-321-6993.
9
MTT3200 O/M.QXD 2/28/03 9:22 AM Page 10
Memcorp, Inc.
Weston, FL
Printed in Hong Kong
|