Mini Compo CD Player
with Radio
Model: MX9790
Memcorp, Inc.
Weston, FL
Printed in Hong Kong
Note: Please read and follow these instructions before using your unit.
LOCATION OF CONTROLS
CONNECTING THE LOUDSPEAKERS
Connect the cables of the two loudspeakers to the corresponding input (R) for the
right speaker and input (L) for the left speaker, located at the back of the unit.
Warning:
z
z
Connect the loudspeakers before powering the unit:
The unit may not work properly or get damaged if you use speakers
different than the ones supplied with the unit
AC OPERATION
Connect the plug to the AC socket of the unit and the other end to a standard AC
outlet.
ATTENTION
1. Do not plug or unplug the power cable while you have wet hands;
2. When planning not to use this unit for a long time, disconnect the power
cable from the wall outlet;
3. When disconnecting the power cord from the wall outlet, do not pull on the
cord in order to avoid shock risks caused by damaged cable.
1. Speakers
2. Function Switch
3. Power Switch
4. Stereo Headphones Jack
5. Volume Control Knob
6. Skip / Backward Search Button
7. Remote Sensor
16. Minute Set Button
17. Repeat Button
18. Play/Pause Button
19. FM Stereo Indicator
20. Stop Button
SET THE CORRECT TIME
Before starting to set the time, make sure that the Function Switch is not on Radio
position.
Press and hold the time button as well as the Hour and Minute buttons simultaneously,
in order to set the time. Release all buttons when reaching the correct time.
21.
CD Door
22. Tuning Knob
8. Skip / Forward Search Button
9. Power Indicator
10. Program Button
11. ON / OFF Alarm Switch
12. Display
23. CD Door Open Button
24. CD Door Close
25. Band Switch
26. AC Socket
27. Left Speaker Jack
RADIO OPERATION
1. Set the Function Selector to Radio position;
2. Set the band selector to AM/FM position;
3. Adjust the TUNING control to tune in a radio station.
(CD, Time, AM/FM Station, Alarm)
13. Alarm Set Button
14. Time Set Button
28. Right Speaker Jack
29. FM Wire Antenna
SET THE ALARM TIME
Before starting to set the alarm time, make sure that the Function Switch is not on
Radio position.
15. Hour Set Button
Press and hold simultaneously the Alarm button as well as the Hour and Minute
buttons, to adjust the alarm time. Release all buttons when reaching the desired alarm
time and the display will go back to regular time.
- 4 -
- 3 -
PROGRAMMING THE CD PLAYER
RADIO WAKE UP FUNCTION
The programming of the CD player should be done during STOP mode.
1. Press the PROGRAM button to begin programming the CD player;
2. Press ꢀSKIP or SKIPꢁ buttons, to select desired track;
3. Press PROGRAM button again to store this track in memory;
4. Repeat steps from 2 to 3 to store more tracks in memory. You can store a
maximum of 19 tracks in the memory.
Select the desired radio station and set the volume to the desired level and
make the following steps:
1. Slide the Function Switch to auto position;
2. Press the ALARM ON/OFF button once to activate the alarm
function and the display will show "((((( • "indicating that the alarm is
ON and press the ALARM ON/OFF button again to cancel;
3. Set the alarm time as indicated at the SET ALARM TIME section
and the unit’s radio will turn on at the pre-selected time.
5. Press PLAY/PAUSE button to play the disc in the programmed order;
6. To stop playing, press STOP;
7. To cancel the programming, press STOP button and open the CD player
door or select a different function (OFF/RADIO etc.)
BUZZER WAKE UP FUNCTION
Follow the same instructions as for Radio Wake up Function, but slide the
Function Switch to Alarm position. The buzzer will sound for 3 minutes.
REPEAT FUNCTION
To repeat the same track:
-
Press REPEAT button before or while playing the song. The REPEAT
symbol " " will light up on the display.
To repeat the whole disc:
CD PLAYER OPERATION
To play a CD, please follow the steps underneath:
1. Set the Function Selector to the CD position;
2. Press the OPEN button in order to open the CD door;
3. Insert the CD with the printed side facing up and close the CD door;
4. Disc information (total number of tracks) will appear on the LED
display;
-
Press REPEAT button twice. The REPEAT symbol "
the display.
To cancel the repeat function:
" will light up on
-
Press REPEAT button three times. The REPEAT indicator will be cleared
from the display.
5. Press PLAY/PAUSE button to start playing the CD;
6. Adjust the volume control to the desired volume level;
7. Press STOP, to stop playing the CD
PAUSE FUNCTION
1. While playing a CD, press PLAY/PAUSE button once to temporarily pause
the play.
2. Press PLAY/PAUSE button again to resume play.
SKIP DURING PLAY MODE
1. Press SKIP ꢀ button once to skip to the beginning of the next track;
2. Press SKIP ꢁ button once to skip to the beginning of the correct
track;
REMOTE CONTROL OPERATION
3. Press SKIP ꢁ twice quickly in succession to go back to previous
Open the Battery Compartment Door and insert two pieces "AAA" size batteries into
the battery compartment with battery polarity as shown inside the battery
compartment.
Point the remote control at the remote sensor. The functions of the buttons on the
remote control are same as the corresponding controls on the main unit.
tracks.
SEARCH DURING PLAY MODE
1. Press and hold the search buttons to quickly advance or reverse
through the music at high speed;
2. Release the ꢀSEARCHꢁ button to return to normal play mode.
- 5 -
- 6 -
1.
2.
3.
4.
5.
6.
Stop Button
USEFULADVICE BEFORE REQUIRING SERVICE SUPPORT
Many of the problems are probably caused by improper adjustments of the product or by
simple problems. Before contacting your Service Centre for help, check the following table.
Skip/SearchꢁButton
Skip/SearchꢀButton
Repeat Button
Play/Pause Button
Battery Compartment
PROBLEM
CAUSE AND REMEDY
GENERAL
No Power Supply
- Check that the power cord is properly
connected to wall out.
No Audio
- Adjust the volume.
Warning:
- You have not connected the speaker boxes;
plug the main unit speaker terminals.
- Your Hi-Fi system is too close to a TV set
or a VCR; move away from the TV set or
the VCR.
When the remote will not be used for a long time, remove the batteries in order
to prevent damage due to electrolyte leakage.
Evident Audio Disturbances
HANDLING A DISC
RADIO RECEPTION
Always protect a disc against scratches, soil and dust etc. We recommend that
the discs should be stored in the original case during non-use periods.
Bear in mind the following points, since any dirt, scratches or
warping of the disc can cause broken or intermittent sound
and also noise.
The FM Stereo Indicator Blinks.
- Rotate the set and extend the FM Antenna.
Evident Audio Disturbance.
- Rotate the set and extend the FM Antenna.
CD OPERATION
z When holding the discs, take care not to touch the playing
surface.
The CD Compartment does not
close
- The disc is not placed correctly in its
compartment.
z Store the discs in their cases. Return them to their cases
with the label surface facing up and push down lightly on
the label surface.
z Do not place discs near a heating device or a place where
the temperature is high or in dusty areas.
z Do not write on the label surface using a ballpoint pen and
do not stick labels on the CD.
z Wipe away any fingerprints or dust on the playing surface
of a disc using a soft cloth.
The Playback does not start
- The CD is dirty.
- The CD was placed wrongly.
- The pause mode was activated.
- Inside the CD player some moisture
condensation occurred; leave the unit in a
warm room for one or two hours.
- The CD surface is dirty or scratched.
No Audio During Playback
If after checking this table the unit fails to operate normally. Consult the nearest Authorized
Service centre.
Bear in mind the following points:
- Always wipe from the inside toward the outside of the disc.
- Never in a circular motion.
- Do not use conventional record cleaners, anti-static agents,
benzene, thinner or other solvents.
- 8 -
- 7 -
CARE AND MAINTENANCE
Precautions
1. Always turn OFF the unit after use;
2. Keep the unit away from magnetic objects, water or any heat sources;
3. Use a clean soft moist cloth to clean the unit’s cabinet. Do not use
chemical cleaners that could damage the finishing of the unit;
4. Never touch the CD pickup lens. If fingerprints get on the pickup lens,
use a commercial lens cleaner.
5. Disconnect the unit from any power sources before starting the
cleaning operation.
SPECIFICATION
CD SECTION
Channels:
2 channels
Pick up light source:
semiconductor laser
RADIO SECTION
Frequency range:
AM 520 - 1710 KHz
FM 87.5 - 108 MHz
FM antenna wire
Antenna:
GENERAL
Power output
Power consumption
Power source
2W + 2W
15W
AC 120V ~ 60Hz
Specifications are subject to change without further notice.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT
OUR WEBSITE AT WWW.MEMOREXELECTRONICS.COM OR CONTACT
CUSTOMER SERVICE AT (954) 660-7100
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN
CASE YOU NEED TO RETURN THIS PRODUCT TO YOUR PLACE OF
PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INTERNATIONAL AT
1-800-321-6993
- 9 -
|