IEEE 1394A and 1394B FireWire/Hi-Speed USB2.0
2.5” Hard Drive Enclosure
PHR-S250UAB
User’s Manual
Introducing IEEE 1394A and 1394B FireWire/Hi-Speed USB2.0
2.5" Hard Drive Enclosure-PHR-S250UAB
Thank you for choosing the PHR-S250UAB portable IEEE 1394A and 1394B
FireWire/Hi-Speed USB2.0 2.5" Hard Drive Enclosure. This portable size
enclosure support 2.5” SATA Hard drive. It is simple to install and comes with
all the parts you need to create a external IEEE 1394A and 1394B FireWire/
Hi-Speed USB2.0 device.
About This Guide
Before you begin using the PHR-S250UAB, be sure to read this manual in its
entirety.
This guide contains:
•
Introducing IEEE 1394A and 1394B FireWire/Hi-Speed USB2.0
2.5" Hard Drive Enclosure
•
•
Hardware Installation
Software Installation
System Requirements
For Mac
• Any Macintosh desktop or NoteBook computer with USB or
FireWire port ready
• MasOS X 10.1.x to 10.7.x and above
For PC
• Pentium II or compatible Desktop or Notebook with USB or
IEEE 1394A and 1394B FireWire port ready.
• WindowsXP, Windows Vista and Windows7
• USB2.0 port is required for Hi-Speed USB2.0 transfer speed
Using AC/DC Adapter (optional)
Basically, if you connect the PHR-S250UAB directly into built-in FireWire
or USB port, AC/DC adapter is not required. However
(1) if USB connection dose not response, or USB port is disable due
to power surge error message
(2) the PHR-S250UAB Enclosure is connected to a CardBus to
FireWire host adapter, or 4-pin iLink port AC/DC adapter is required.
3
Package Contents
The PHR-S250UAB portable IEEE 1394A and 1394B FireWire/Hi-Speed
USB2.0 2.5" Hard Drive Enclosure package includes the following software and
documentation:
•
•
•
•
6 pin to 6 pin FireWire Cable
9 pin to 9 pin FireWire Cable
USB2.0 cable
IEEE 1394A and 1394B FireWire/Hi-Speed USB2.0 2.5" Hard Drive Enclosure
Safety Precautions
ON INSTALLATION
1. To reduce the risk of fire or electric shock, do not expose this
product to rain, water or moisture.
2. Do not place any containers with liquids (drinking glass, flower
vase, etc.) or containers with small metal parts (paper clips, etc.)
on top of the unit.
3. According to standard industry practice, surge protection is
recommended for all telecommunications devices. Surge suppressors
and/or line conditioning should be used on the input power supply.
ON OPERATION
•
Do not move the chassis during operation. Doing so may cause
a malfunction.
•
•
Protect the unit from shocks and vibrations.
Do not use the subsystem in areas exposed to oily smoke or steam,
such as a kitchen or close to a humidifier.
•
•
•
Do not use the subsystem in locations exposed to rain or splashes of
water, such as outdoors, in a bathroom, or close to a window.
Do not use the subsystem on an unstable or slanted surface without
proper support.
Do not expose the unit to direct sunlight or hot air where the
temperature could exceed 45ºC, or very cold locations where the
temperature is below 0ºC.
•
•
Keep the power cord away from hot appliances.
Do not touch the power cord with wet hands.
4
ON TRANSPORTATION
Save the packing materials as you may need to repack and transport the
unit at a later date.
Always remove the disc before moving the unit.
ON POWER SOURCES
When you are not using the unit for a long time, disconnect the power cord
from the unit.
To unplug the AC power adapter from the wall outlet, grasp the adapter
itself. Do not pull the cord.
Warning
If any of the following conditions occur, immediately disconnect the power
cord from the wall outlet and contact your dealer or an authorized service
station. Continuing to use the computer involves the risk of fire and electric
shock.
•
•
•
•
•
Smoke or unusual smell is coming from the subsystem.
Water has entered the unit, or the unit has become wet.
A foreign object has entered the unit.
The unit has been dropped or the front panel or frame has been damaged.
The power cable is damaged, causing wire breakage or exposed leads.
5
Hardware Basic
Precaution:
1) Please connect the enclosure directly to your computer.
2) Please make sure your hand is dry and remove static from
your body by touching metal parts of your computer chassis.
Enclosure Sleeve
Circuit Board
Bottom Tray
Back Panel
LED
Power
Connector
USB Data
1394B FireWire Data
Cable connector
Cable connector
1394A FireWire Data
Cable connector
Package Content:
Enclosure Sleeve
Circuit Board
1 USB Data Cable
1 FireWire Data Cable (1394A)
1 FireWire Data Cable (1394B)
4 - 5mm Diameter Screws
2 - 3mm Diameter Screws
Back Panel
Bottom Tray
6
Hardware Installation
1. Unscrew to loosen the Enclosure Back Panel.
2. Remove the Back Panel from the Enclosure.
3. Use both thumbs to push the Bottom Tray out.
7
4. Align the pins on the hard drive to the 22PIN SATA connector,
and push the drive in completely.
(b)
(a)
5.(a) Seat the Circuit Board and hard drive on the Bottom Tray. (b) Secure
the hard drive with Screws (5mm in diameter) on the bottom of the tray.
(a)
(b)
hard drive & circuit board
Bottom Tray
6.Align the Bottom Tray to the Sleeve Slot. Slide and push the hard drive/
Bottom Tray into the Enclosure Sleeve.
8
7. Put the Back Panel back to the Enclosure.
8. Secure the Back Panel with 2 screws (3mm in diameter) from each side.
9. Connect the Enclosure directly to the computer by using the USB or
FireWire cable and it is now ready to use.
9
Software Installation
Software Installation for MasOS X 10.1.x to 10.7.x and above
FireWire Connection for MasOS X 10.1.x to 10.7.x and above
When the enclosure is connected to the computer, MasOS X 10.1.x to 10.7.x
and above will recognize it automatically, initialize (if the drive is not
initialized) and mount the drive to desktop.
USB Connection for MasOS X 10.1.x to 10.7.x and above
When the enclosure is connected to the computer, MasOS X 10.1.x to 10.7.x
and above will recognize it automatically, initialize (if the drive is not
initialized) and mount the drive to desktop.
* Plug in the USB2.0 enclosure and it is ready to use. For USB2.0
performance, you must plug the enclosure into a USB2.0 port and
MasOS X 10.1.x to 10.7.x and above, or you will get USB1.1
performance only.
Note: Whether it is FireWire or USB Connection, MasOS X 10.1.x to 10.7.x and above
provides a Disk Utility to create multiple volumes, which is located in Utilities folder
inside Applications folder.
10
Software Installation for PC
IEEE1394 FireWire Connection for WindowsXP/Vista/Windows7
Plug the IEEE 1394 cable into any available port, WindowsXP/Vista/
Windows7 will start installing for the proper driver. Please follow the on
screen instruction to complete the driver installation. (You may need the
Windows CD during the installation.)
USB Connection for WindowsXP/Vista/Windows7
Plug the USB cable into any available port, WindowsXP/Vista/
Windows7 will start installing for the proper driver. Please follow the on
screen instruction to complete the driver installation.
After the installation, you will get USB2.0 Hi-Speed performance, if
PHR-S250UAB is connected to USB2.0 host adapter; if connected to USB1.1
port in your computer, you will get USB1.1 speed only.
Note: If you don’t see the new drive letter added in My Computer after
driver is loaded properly, the reason could be the hard disk has no
partition and format yet, please partition and format the drive in the
enclosure before using it.
11
SATA HARD DRIVE PARTITION and
FORMAT PROCEDURES in PC
For WindowsXP/Vista/Windows 7
If you can see a new entry under Disk drives of Device Manager, you are
ready to partition and format the drive.
1. Open Control panel, “Administrative Tools” and “Computer management”.
Step 2
2. Click on “Disk Management”.
Step 3
12
3. “Write Signature and Upgrade Disk Wizard” windows will show up and
click “Next”.
Step 4
4. Write a signature to the new drive, click “Next”.
Step 5
5. Click “Finish” to close the wizard.
13
6. Select the new “Unallocated” disk, and then right click to choose
“Create partition”.
Step 7
7. Follow the onscreen instruction to partition and fully format the drive.
*note: If it assigns a new hard drive letter but format dose not run automatically,
please exit “Computer Management”, and find the new drive letter in My computer to
format it completely.
14
|