®
COMPACT DISC PLAYER
AM/FM DUAL CASSETTE RECORDER
WITH REMOTE CONTROL
MODEL CD-162
OPERATING INSTRUCTIONS
INCLUDES FULL FEATURE REMOTE CONTROL
•
MULTI-COLORED FLUORESCENT DISPLAY
•
PLAYS ALL MUSIC COMPACT DISCS
•
KARAOKE FUNCTION WITH DUAL MIC. JACKS
•
FULLY PROGRAMMABLE CD PLAYER WITH REPEAT PLAY
•
RECEIVES AM/FM STEREO BROADCASTS
•
ROTARY BASS & TREBLE CONTROLS
•
RECORDS FROM CD, TAPE OR RADIO
•
2 WAY POWER - AC/DC
•
REQUIRES 8 SIZE “D” BATTERIES (NOT INCLUDED)
•
PLEASE READ CAREFULLY BEFORE USE
IB-CD162(SLIM)-TA-V1
SAFETY INSTRUCTIONS
14. Object and Liquid Entry - Care should be taken so that objects do not fall and liquids
are not spilled into the enclosure through openings.
15. Damage Requiring Service - The appliance should be serviced by qualified service
personnel when:
A. The power supply cord or the plug has been damaged; or
B. Objects have fallen, or liquid has been spilled into the appliance; or
C. The appliance has been exposed to rain; or
D. The appliance does not appear to operate normally or exhibits a marked change in
performance; or
E. The appliance has been dropped, or the enclosure damaged.
16. Servicing - The user should not attempt to service the appliance beyond that described in the
operating instructions. All other servicing should be referred to qualified service personnel.
17. Power lines - An outdoor antenna should be located away from power lines.
18. Outdoor Antenna Grounding - If an outside antenna is connected to the receiver, be sure the
antenna system is grounded so as to provide some protection against voltage surges and
built up static charges. Section 810 of the National Electrical Code, ANSI/NFPA 70 provides
information with respect to proper grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of
antenna-discharge unit, connection to grounding electrodes, and requirements for the
grounding electrode. See Figure.
EXAMPLE OF ANTENNA GROUNDING AS PER
NEC - NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
It is the intent of Lenoxx that this product be used in full compliance with the
copyright laws of the United States and that prior permission be obtained from
copyright owners whenever copying tapes or CD’s.
Do not apply oil or petroleum products or solvents to any part of this set.
CAUTION
Use of controls or adjustments or performance of procedures other than those
specified herein may result in hazardous radiation exposure.
This compact disc player is classified as CLASS 1 LASER PRODUCT as stated
on the back of the set.
2
IB-CD162(SLIM)-TA-V1
BATTERY SAFETY INSTRUCTIONS
TO REDUCE THE RISK OF FIRE OR PERSONAL INJURY OR DAMAGE TO YOUR
CAUTION:
SET, READ AND FOLLOW THESE INSTRUCTIONS.
1. Use only the type and size of batteries mentioned in the operating instructions
booklet (batteries are not included with this set, please buy the proper batteries).
2. Do not dispose the batteries into a fire. The cells may explode. Check with local
codes for possible special disposal instructions.
3. Do not open or mutilate the batteries. Released electrolyte is corrosive and may
cause damage to the eyes or skin. It may be toxic if swallowed.
4. Be careful when handling batteries in order not to short the battery with conducting
materials such as rings, bracelets and keys. The battery or conductor may over
heat and cause burns.
5. Do not attempt to recharge non-rechargeable batteries. The batteries may leak
corrosive electrolyte or explode.
6. Do not attempt to rejuvenate the batteries identified for use with this product by
heating them. Sudden release of the battery electrolyte may cause burns or
irritation to eyes or skin.
7. All batteries should be replaced at the same time. Mixing fresh and discharged
batteries could increase internal cell pressure and rupture the batteries.
8. When inserting batteries into this product, the proper polarity (
and
) or
direction must be observed. Reverse insertion of some or all of the batteries may
result in battery electrolyte leakage or explosion.
9. Remove the batteries from this product if the product will not be used for a long
period of time (several months or more) since during the period the batteries could
leak, damaging the product.
10. Discard weak or dead batteries as soon as possible since they are more likely to
leak in the product. Batteries should be replaced (depending on the product) when
the display gets dim or if the Low Battery Indicator shows or if the sound gets
distorted.
11. Do not store this product in high temperature areas. Batteries that are stored in a
freezer or refrigerator for the purpose of extending shelf life should be protected
from condensation during storage and defrosting. Batteries should be stabilized at
room temperature prior to use after cold storage.
12. If this product does not operate normally, see TROUBLE SHOOTING in this
instruction manual. If you can’t resolve the problem, or if the product is damaged, refer to the
LENOXX WARRANTY INFORMATION. Opening or removing covers may expose you to
dangerous voltages or other risks. Incorrect reassembly can cause electric shock when
the appliance is subsequently used.
13. If liquid leaks from the batteries, carefully wipe this liquid. Do not allow it to touch your skin,
and discard the leaking batteries.
14. Do not mix batteries (OLD and NEW or CARBON and ALKALINE, etc.).
15. The use of rechargeable batteries is not recommended for this set because their
voltage and life is lower than standard batteries.
16. Installation of batteries should be done by an adult only.
SAVE THESE INSTRUCTIONS
IB-CD162(SLIM)-TA-V1
3
CHOOSING THE POWER SOURCES
You can use AC power or batteries as a power source.
To a wall outlet
NOTE: One blade of plug
and outlet is wider.
AC SOCKET
1. Connecting the AC power
cord
Insert one end of the supplied AC power cord (located
in the battery compartment) into the socket located
at the back of the set, and the other end to the wall
outlet.
TIP
If the plug of the AC power
cord does not match your
outlet, do not force it.
Reverse it and try again.
The plugs are polarized
and only fit one way into the
wall outlet and back of the
set.
2. Using battery power
Insert 8 size “D” batteries (not supplied) into the battery
compartment.
To use the player on batteries, disconnect the AC power
cord from the player.
TIP
Replace the batteries
when the POWER/BATT.
INDICATOR gets dim or
when the set stops
operating. Replace all the
batteries with new ones.
Before you replace the
batteries, be sure to take
out the CD from the player
and remember to check the
Battery Safety Instructions
on Page 3.
UPPER
LOW ER
VFD DISPLAY
The VFD display only light up when using AC
power.
IB-CD162(SLIM)-TA-V1
4
ATTACHING THE SPEAKERS
1.Bring one of the speaker to the right side of
the set.
2. Align the rails of the speaker box with the
main set as shown in FIG.1.
FIG.1
3. When speaker align with the rails, push the
speaker into the rails as shown in FIG. 2.
4. Repeat above steps 1 to 3 for the left
side.
FIG.2
5.Carefully unwind the speaker wire from behind each speaker box and plug the
right plug into Speaker Jack R, also plug the left plug into Speaker Jack L (as
shown in FIG. 3). Wrap the remaining wire behind each speaker box.
LOCK TAB
FIG.3
NOTE: This set can be used with speaker boxes attached to the cabinet or
separated, just make sure both speaker plugs are plugged into the jacks.
To remove the speakers, press the lock tab and push the speakers out
of the rails.
IB-CD162(SLIM)-TA-V1
5
REMOTE CONTROL
You can control the CD PLAYER with the provided REMOTE CONTROL (including the
functions of POWER ON/OFF, MUTE, VOLUME control, CD REPEAT and PLAY features).
NOTE: When you use the ROMOTE CONTROL to operate the CD PLAYER,
make sure the POWER switch on the main set is turned on, otherwise,
the ROMOTE CONTROL will have no functions to the set.
1. POWER ON/OFF
2. MUTE
9
1
3. REPEAT - ONE & ALL SONGS
4. PROGRAM
5. VOLUME UP/DOWN
6. SKIP/SEARCH BACKWARD
7. SKIP/SEARCH FORWARD
8. STOP
8
2
3
7
9. PLAY/PAUSE
4
6
NOTE: When you press the POWER
ON/OFF switch to shut the set
off, the STANDBY indicator on
the main set will turn on.
5
Slide the battery cover to remove. Insert two size “AAA” batteries correctly so that the +
and - polarities match the polarity diagrams inside the battery compartment.
NOTE:
About half a year of normal operation can be expected when using the
•
alkaline batteries.
when the batteries are exhausted, the remote control will no longer
•
operate the system. Replace both batteries with new ones.
When the remote control is not to be used for a long time (2 months or
•
more), remove the batteries to avoid possible damage that may be caused
by battery leakage.
Avoid keeping the remote control in extremely hot or humid locations.
•
•
The remote control’s operating distance is about 0.2m (8 inches) to 6m
(20 feet) away from the remote sensor.
IB-CD162(SLIM)-TA-V1
6
PLAYING A CD
1
3
2
5
6
Connect the supplied AC power cord or batteries (see page 4).
STANDBY
Press the POWER switch, the
POWER/BATT. lamp and the VFD
display will turn on.
1
2
POWER
RADIO
Rotate the FUNCTION switch to CD
position, two dashes “--” will show
on the VFD display.
TAPE
CD
Open the CD DOOR by pressing the
right corner marked OPEN/CLOSE
and place the CD in the CD
compartment.
The label side of the CD should face
upward.
3
4
Close the CD DOOR by pushing it
down. The display will show the total
number of tracks (songs) on that
CD.
Press the CD PLAY button. The
player will play all the songs (tracks)
once in order.
5
6
PLAY/PAUSE
To change the sound effect, adjust
the BASS and TREBLE knobs to
your taste.
TREBLE
BASS
TIP: “ ” WILL SHOW IN THE DISPLAY IF THERE IS NO DISC IN THE CD
COMPARTMENT OR IF THE DISC IS UPSIDE DOWN.
IB-CD162(SLIM)-TA-V1
7
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
VOLUME CONTROL
TIP
When CD play is
paused,
“
”
will
flash and no music
will play.
FUNCTION SWITCH
To
Press or Adjust
Adjust the volume
Stop playback
VOLUME control
To resume play,
press the PAUSE
STOP
button again, “
”
PLAY/PAUSE
will stop flashing
and music will play.
“
” will flash during pause.
Press again to resume play
after pause.
Pause playback
TIP
If you bump the set
or the table it is
sitting on, during
CD play, the music
will stop or skip for
Go to the next track
FORWARDS
BACKWARDS
Go back to the previous
track
a
few seconds.
This is normal for
this type of player.
or
Press and hold down while
playing until you find the
point.
Locate a point in a song
TIP
This set has an
electronic volume
control, you may
raise or lower the
volume by pressing
the VOLUME
(UP) and - (DOWM)
buttons.
Press the right corner of the
CD DOOR marked OPEN/
CLOSE (press STOP first).
Remove the CD
Turn off the power
+
Press the POWER switch, the
display and the POWER/BATT.
lamp will go off.
IB-CD162(SLIM)-TA-V1
8
REPEAT PLAY
PLAYING CD SONGS (TRACKS) OVER AND OVER
You can play CD tracks over and over in normal or program play modes (see page
10). (NOTE: To use this feature, you need to operate the set with the REMOTE
CONTROL, because there is no REPEAT button on the main set.)
POWER FUNCTION
SWITCH
SWITCH
REPEAT
1. Press the POWER switch, the POWER/BATT. lamp will turn on and the display will
light up.
2. Set the FUNCTION switch to CD position.
3. Select the track by pressing
or
, and then press
.
4. Press the CD REPEAT button on the REMOTE CONTROL.
To repeat
Display shows
“REP” will flash.
Press
a single track (song)
Press the REPEAT
button once
REP
Press the REPEAT
button twice
“REP” will be
steady on
all the tracks (all songs)
programmed tracks
REP
During programmed play,
“REP” is steady
on
press
the
REPEAT
button twice
To cancel Repeat Play
Press the REPEAT button until the “REP” goes off.
IB-CD162(SLIM)-TA-V1
9
PROGRAMMED CD PLAY
SELECTING YOUR OWN MUSIC PLAYING ORDER
You can make a program of up to 19 tracks to
play in the order you want them to be played.
PROGRAM
NOTE: Programming is only done during
stop mode.
During STOP mode, press the
PROGRAM button. ” and
1
2
3
“
“PROGRAM” will flash in the
display.
PROG.
SKIP/SEARCH
PROG.
Press the SKIP/SEARCH buttons
either
or
until the desired
track shows in the display.
Press the PROGRAM button. “
”
and “PROGRAM” will flash in the
display.
Repeat steps 2&3 until all the
desired tracks are programmed.
4
5
Press the PLAY button to start
programmed play.
“
”
,
“PROGRAM” and the track
number being played will show in
the display.
PLAY/PAUSE
To change the current program
Just create a new program following the programing procedure.
To cancel Program Play
Press the STOP button twice, “PROGRAM” will disappear from the display.
IB-CD162(SLIM)-TA-V1
10
LISTENING TO THE RADIO
2
3
4
1
6
Connect the supplied AC power cord or batteries (see page 4).
Press the POWER switch, the
POWER/BATT. lamp and the VFD
display will turn on.
1
Set the FUNCTION switch to
RADIO position.
2
3
STEREO
MONO
HIGH SPEED
NORMAL
Set the BAND switch to the proper
band position (AM or FM), and set
the FM MODE switch to STEREO
or MONO.
DUBBING SPEED
FM MODE
Tune into the station you prefer
using the TUNING control. Adjust
for the clearest sound.
4
This indicator will light up when
receiving FM Stereo broadcasts.
5
6
You may adjust the BASS and
TREBLE controls to change the tone
of the set to your taste.
BASS
TREBLE
IB-CD162(SLIM)-TA-V1
11
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
FM MODE
VOLUME
FUNCTION
TIP
To
Press or Set
If the FM broadcast is
•
noisy, set the FM MODE
switch from STEREO
to MONO.
Adjust the volume
VOLUME control (“+” or
“-” ).
Set the FUNCTION switch
to TAPE position or press
the POWER switch.
Turn off the Radio
This set has an
•
electronic
volume
control, you may raise
or lower the volume by
pressing the VOLUME
+ (UP) and - (DOWN)
buttons.
To improve broadcast reception
Change position of the antenna for FM or FM Stereo.
Move the set itself for AM.
IB-CD162(SLIM)-TA-V1
12
PLAYING A TAPE
1
2
3
4
Connect the supplied AC power cord or batteries (see page 4).
Press the POWER switch, the
POWER/BATT. lamp and the VFD
display will turn on.
1
2
3
FULL
REEL
EMPTY
REEL
RADIO
Set the FUNCTION
switch to TAPE position.
CD
TAPE
A
Press the STOP/EJECT
IN S ER T TH IS W AY
button (DECK
A
or
DECK B) to open the
tape compartment and
insert a recorded tape.
Close the door.
STOP/EJECT
Press the PLAY button.
The player turns on and
starts playing.
4
5
PLAY
When the set finishes
playing one side of the
tape, the set will stop. To
hear the other side of the
tape, flip the tape over,
then insert and press
PLAY.
AUTO STOP
IB-CD162(SLIM)-TA-V1
13
RELAY PLAY
1
2
5
4 3
Connect the supplied AC power cord or batteries (see page 4).
To play tapes in DECK A and then DECK B, follow the steps below:
Press the POWER switch, the POWER/
BATT. lamp and the VFD display will turn
on.
1
RADIO
Set the FUNCTION switch to TAPE
position.
CD
TAPE
2
3
Press the cassette PLAY button on
DECK A, DECK A will play.
PLAY
Press the cassette PAUSE button on
DECK B.
4
PAUSE
PLAY
Press the cassette PLAY button on
DECK B. When DECK A finishes playing,
DECK B will start playing automatically.
5
6
When the tape finishes playing on DECK
B, the set will stop.
IB-CD162(SLIM)-TA-V1
14
USE THESE BUTTONS FOR ADDITIONAL
CASSETTE TAPE OPERATIONS
VOLUME
CONTROL
PAUSE
PAUSE PLAY
STOP/EJECT
PLAY
STOP/EJECT
RECORD
REWIND & FAST F.
REWIND & FAST F.
To
Press or Adjust
Press the VOLUME button ( “+”
or “-”)
Adjust the volume
Stop playback
STOP/EJECT button
Fast forward or rewind
the tape
FAST FORWARD button or
REWIND button
Pause playback
PAUSE button
Press again to resume play after
pause.
Eject the cassette
STOP/EJECT button
Insert your headphone plug into
the HEADPHONE jack (at the back
of the set).
To enjoy the music
without disturbing others
(headphones are not
included)
To shut power off
Make sure cassette buttons are all
up (stop) and POWER switch is off.
IB-CD162(SLIM)-TA-V1
15
RECORDING ON A TAPE
1
3
MICROPHONE JACKS
4
2
Connect the supplied AC power cord or batteries (see page 4).
STANDBY
Press the POWER switch, the POWER/
1
2
BATT. lamp and the VFD display will turn
on.
POWER
OK
NO
Press the STOP/EJECT button (DECK
B) to open the tape compartment and
insert a blank tape. Select the program
source (AM, FM, CD, or microphone)
you want to record.
STOP/EJECT
RADIO
TAPE
CD
To record from the CD player, set the FUNCTION switch to
CD position, insert a CD and follow the steps to play a CD
(see page 7).
3
RADIO
TAPE
To record from a radio, set the FUNCTION switch to RADIO
position, and tune into the station you want (see page 11).
OR
OR
CD
To record from the microphone, set the FUNCTION switch to
the TAPE position, and plug the microphone(s) (not included)
into either of the MIC JACKS. Speak into the microphone.
RADIO
CD
TAPE
To record from the DECK A, set the FUNCTION switch to the
TAPE position, and follow the steps to play a TAPE (see
page 13).
THEN
Press the RECORD button to start recording. (The PLAY
button is depressed automatically.)
4
RECORD
To hear what you recorded, set the FUNCTION switch to
TAPE position, then press REWIND and PLAY.
5
REWIND PLAY
IB-CD162(SLIM)-TA-V1
16
USE THESE BUTTONS FOR
ADDITIONAL OPERATIONS
DUBBING SPEED
SWITCH
TIP
STOP/EJECT PAUSE
• For best recording
effect, use the AC
power instead of
batteries.
Press or Set
To
• To
erase
a
recording, just start
a new recording,
and the old one is
a u t o m a t i c a l l y
replaced.
Stop recording
STOP/EJECT button
Pause recording
PAUSE button
Press the button again
to resume recording.
• see page 21 for
notes on cassettes.
Adjust recording speed
when copying tapes
DUBBING SPEED
switch from NORMAL
to HIGH speed.
Turn off the power
Press the STOP/EJECT
button and press the
POWER
switch,
the
POWER/BATT. lamp will go
off.
IB-CD162(SLIM)-TA-V1
17
SINGING ALONG WITH KARAOKE FUNCTION
MIC
VOLUME
VOLUME
MICROPHONE JACKS
2
Connect the supplied AC power cord or batteries (see page 4).
Insert microphone plugs into the microphone jacks.
To avoid mic howling, lower the volume level setting
first.
1
2
MIC 1
MIC 2
NOTE: Microphones are not included, you may
purchase microphones where you bought
this set.
RADIO
CD
TAPE
To sing along with the CD player, set the FUNCTION
switch to CD position, insert a KARAOKE CD disc
and follow the steps to play a CD (see page 7).
RADIO
To sing along with the tape, set the FUNCTION
switch to the TAPE position, insert a KARAOKE
TAPE into deck A or B, and follow the steps to
play a TAPE (see page 13).
CD
TAPE
Press the CD PLAY/PAUSE button on the CD player
or press the PLAY button on deck A or B.
3
4
PLAY/PAUSE
PLAY
Adjust the volume controls (both the set’s VOLUME
control and the MICROPHONE VOLUME control)
to achieve the best effect.
MIN
MAX
MIC
VOLUME
IB-CD162(SLIM)-TA-V1
18
USE THESE BUTTONS FOR ADDITIONAL
OPERATIONS
VOLUME
CONTROL
MIC VOLUME
BASS
BALANCE
TREBLE
To
Press or Adjust
Adjust the MIC volume
MIC VOLUME
MIN
MAX
MIC
VOLUME
VOLUME
Adjust the CD or TAPE
music volume
VOLUME control
BALANCE control
Adjust the RIGHT & LEFT
channel output.
BALANCE
BASS or TREBLE
controls.
Adjust the sound effects
for low thigh tones.
BASS
TREBLE
TIP: If there is squealing or howling (feedback) noise during KARAOKE
use, move the microphone away from the speakers or turn down
the volume. Set the KARAOKE switch to OFF position for better
music play.
IB-CD162(SLIM)-TA-V1
19
PRECAUTIONS
On Safety
On Power Sources
For battery operation, use 8 size D
batteries. We recommend alkaline
batteries for longer life.
As the laser beam used in the CD
•
•
player section may be harmful to the
eyes, do not attempt to disassemble
the cabinet.
Refer servicing to
If the batteries will not be used
•
qualified personnel only.
for a few weeks or more, remove them
to avoid damage that can be caused
by battery leakage.
Should any solid object or liquid fall
into the set, unplug the player, and
have it checked by qualified personnel
before operating it any further.
•
On Operation
If the set is brought directly from a
On Placement
Do not leave the set in a location
near a heat source, or in a place
subject to direct sunlight, excessive
dust or mechanical shock.
•
•
cold to a warm location, or is placed
in a very damp room, moisture may
condense on the lens inside the CD
player section. Should this occur, the
set will not operate properly. In
this case, remove the CD and wait
about an hour for the moisture to
evaporate. If the set has not been
used for a long time, set it in the
playback mode to warm it up for a few
minutes before inserting a cassette.
Do not place the set on an inclined
•
or unstable place.
Do not place anything within 1 inch of
•
the back of the cabinet. The
ventilation holes must not be covered
for the set to operate properly and
prolong the life of its components.
This set is designed to be played on
•
If the set is left in a car parked in the
•
a stable no vibration position. If you
bump the set during CD play, the music
will stop or skip for a few seconds.
This is normal for this type of player.
sun, be sure to choose a location in
the car where the set will not be
subjected to the direct rays of the
sun.
If you have any questions or problems
•
Since a strong magnet is used for the
•
concerning your player, please contact
our customer service department at
1-800-315-5885.
(Monday - Thursday 09:00 AM - 05:00 PM,
Friday 09:00 AM - 01:00 PM EST)
speakers, keep personal credit cards
using magnetic coding or springwound
watches away from the speakers to
prevent possible damage from the
magnets.
IB-CD162(SLIM)-TA-V1
20
PRECAUTIONS (continued)
Notes on CDs
Notes on Cassettes
Break off the cassette recording tabs
Before playing, clean the CD with a
•
•
cleaning cloth. Wipe the CD from the
center out.
from side A or B to prevent accidental
recording.
Side A
Do not use solvents such as benzene,
•
Tab for side A
Tab for side B
thinner, commercially available
cleaners or anti-static spray intended
for vinyl LPs.
Do not expose the CD to direct
•
sunlight or heat sources such as hot
air ducts, nor leave it in a car parked
in direct sunlight as there can be a
considerable rise in temperature inside
the car and result in a damaged CD.
To record on a tape with its tab broken
off, cover the respective tab hole for
side A or B with adhesive tape.
•
The use of a cassette with more than
•
90 minutes of play time is not
recommended except for long
continuous recording or playback.
Do not stick paper or stickers on the
•
CD, nor scratch the CD.
To reduce the chances of tape
After playing, store the CD in its case.
•
•
jamming or tangling, you should check
that there are no loose layers of tape
visible through the cassette center
window. If any, tighten these loose
layers of tape using a pencil before
inserting the cassette into the set.
If there is a scratch, dirt or fingerprints
on the CD, it may cause a tracking
error or skipping.
IB-CD162(SLIM)-TA-V1
21
MAINTENANCE
Cleaning the Lens
Notes for Storing
Cassette Tapes
1. Do not put a tape near a magnetic
field, such as a TV, or speaker.
Magnetic fields may reduce the tape
sensitivity or even erase the
recording.
If the lens becomes dirty, it may cause a
skipping of sound during CD operation.
Clean with a commercially available lens
cleaner and blower.
2. Do not store tape for any length of
time in a hot, moist or dusty place.
Cleaning the Tape Heads
Wipe the heads, the pinch roller and
the capstan with a cleaning swab slightly
moistened with cleaning fluid or alcohol
after every 10 hours of operation for
optimum playback and recording quality.
After cleaning, insert a tape when the
areas cleaned are completely dry.
Cleaning the Cabinet
Clean the cabinet, panel and controls
with a soft cloth slightly moistened with
water or a mild detergent solution. Do
not use any type of abrasive pad,
scouring powder, or solvent, such as
alcohol or benzene.
COTTON SWAB
CAPSTAN
PINCH ROLLER
ERASE HEAD
RECORD/PLAY BACK HEAD
NOTE: In order to see and clean the
head, you may have to press
PLAY first.
IB-CD162(SLIM)-TA-V1
22
TROUBLE SHOOTING
Problem
Remedy
Connect the AC power cord to a wall
•
outlet securely.
The power is not on.
Make sure the batteries are inserted
correctly and they are fresh.
Make sure the FUNCTION switch is at the
right position as you want.
•
•
There is no sound.
Adjust the volume.
•
•
Unplug the headphones when listening
through speakers.
You may use battery power, the VFD
display only light up when using AC power.
VFD display does not light
up.
•
“
” appears in the display
Insert the CD with the label side up.
•
•
even when a CD is in place.
Make sure that the CD compartment is
closed.
Place the CD with the label side up.
Clean the CD.
•
•
•
CD does not play.
Take out the CD and leave the CD DOOR
open for about an hour to dry moisture
condensation.
Make sure the FUNCTION switch is at CD
position.
•
•
•
Clean the CD, or replace it if the CD is
badly damaged.
The sound drops out.
Place the player in a location free from
vibration.
Check if your batteries are fresh.
•
•
Replace all the batteries with new ones if
they are weak, or bring the set near a
window, or rotate the set.
The sound is weak, or has
poor quality.
Make sure the safety tab on the cassette
is in place (see page 21).
•
•
The RECORD button does not
function/The tape does not
play.
Make sure the FUNCTION switch is at TAPE
position.
Clean the erasing head (see page 22).
Replace all the batteries with new ones if
they are weak.
•
•
The tape does not erase
completely.
Make sure the tape is inserted properly.
Make sure the safety tab of the cassette
is in place.
•
•
The tape does not record.
Clean the heads, pinch roller and capstan
(see page 22).
The sound is weak/The
sound quality is poor.
•
•
The tape has reached its end. Remove
it, flip to the other side and re-insert.
IB-CD162(SLIM)-TA-V1
Cassette PLAY button pops
up.
23
SPECIFICATION
General Description
Power source:
AC 120V, 60Hz 22Watts
DC 8 size “D” batteries for set
DC 2 size “AAA” batteries for Remote Control
(Alkaline batteries are recommended)
Speakers (2 ways):
and
2 - 5” 4 ohm woofers
2 - 3” 4 ohm tweeters with crossover
Output power:
Dimensions:
5.0W/channel
1
Width: 24 / ”
4
1
Depth: 8 / ”
2
7
Height: 12 / ”
8
Weight: 15.4LBs
CD Section
Plays disc type:
Any normal CD used in portable players
760 - 800 NM
Laser wavelength:
Tracking method:
3 - spot error detection
50Hz - 15kHz +1/-2 dB
3.86 mm lens
Frequency response:
Tape Recorder Section
Frequency response: Standard normal bias cassette tape,
70Hz - 10kHz
Radio Section
Frequency range:
FM: 88 - 108 MHz
AM: 530 - 1700 kHz
LENOXX reserves the right to make design and specification changes for product
improvement.
PROTECT YOUR FINE FURNITURE!
WE RECOMMEND ACLOTH OR OTHER PROTECTIVE MATERIAL BE PLACED UNDER
THE SET WHEN PLACING IT ON SURFACE WITH A NATURAL OR LACQUER FINISH.
IB-CD162(SLIM)-TA-V1
24
LIMITED WARRANTY
We warrant this product to be free from defects in material and workmanship
under normal use for a period of 90 days after purchase and we will repair it free of
charge or replace it at no charge, should it become defective under this warranty,
providing you submit proof of purchase (sales slip) with the set.
During the initial 90 day period after original purchase, we will service or
exchange, at no charge, the set that is returned to LENOXX ELECTRONICS
CORP. After the initial 90 day period expires, and for a period of 12 months from
original purchase, we will repair the unit covering any part(s) that need to be
replaced at no charge, but will charge for the cost of labor, return postage paid by
Lenoxx.
This warranty does not apply to any products which have been subject to misuse,
neglect or accident. This warranty does not cover broken cabinet. UNDER NO
CIRCUMSTANCES WILL LENOXX ELECTRONICS CORP. BE LIABLE FOR ANY
INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above
limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state. The following charges apply to repairs beyond the
warranty period: $45.00. Be sure to pack carefully and return postage paid insured
together with your money order (personal checks will not be accepted) and sales
receipt to :
LENOXX ELECTRONICS CORP. 2 GERMAK DRIVE, CARTERET N.J. 07008
For customer service
Dial 1-800-315-5885
(MONDAY - THURSDAY 9:00 AM - 5:00 PM, FRIDAY 9:00 AM - 1:00 PM EST)
or Visit Our Website: http://www.lenoxx.com
© 2001 LENOXX ELECTRONICS CORP.
2 GERMAK DRIVE
CARTERET, N.J. 07008
MADE & PRINTED IN CHINA
IB-CD162(SLIM)-TA-V1
25
|