P03 / P06 / P09
®
INTRODUCTION
Dear Customer,
Thank you for choosing our product.
This machine, thanks to its reliability, will be able to win your preference also
for other products in our range.
Each dealer will be able to refer you to the nearest Service Centre.
Notwithstanding the ease of use of the machine, in order to get the best
results it is important to thoroughly read this booklet and follow all
instructions before starting the machine.
GENERAL INFORMATION
The machine is suitable for preparing hot drinks, obtained by mixing hot
water and granulated soluble products. The body of the machine is designed
for indoor use only.
Any service or repair work, with the exception of cleaning and normal
maintenance, shall be carried out by an authorised Service Centre.
To make reading of the manual easier, important information, which must be
observed for the safeguard of the user and for the prevention of accidents,
will be shown in bold and in some cases indicated by the following symbols:
GENERIC HAZARD: it indicates important rules to be observed
in order to avoid hazards to the user.
ELECTROCUTION HAZARD: it indicates important information
to be followed in order to avoid risks resulting from electric
power
The machine was conceived for use by adult persons only, who have their
psycho-physical faculties unaltered. It is not suitable for use by children.
IMPORTANT PRECAUTIONS
When using electric material it is important to ensure the appropriate
precautions are adopted in order to avoid electric shock, accidents
and damage to persons and things.
SAFETY REGULATIONS
Make sure to implement all necessary precautions to avoid contact of the
machine with liquids. Liquids can seep inside the machine and cause short-
circuits or energise external parts of the machine.
•
Thoroughly read all information contained in this manual and in any
other attachment included in the packing.
INTENDED USE OF THE MACHINE
The machine is intended for adult persons informed on its operation, to be
used in a sensible, conscious and careful manner (should the machine be used
by other persons, we recommend to make this booklet available to them).
It is intended for indoor use only.
• Ensure that the power supply voltage indicated on the data plate of the
machine is compatible with the one from your power supply outlet.
• Take special care while using the machine in the presence of children.
• Verify that the main switch of the machine is not pressed before
plugging or unplugging the power supply plug.
• Unplug the power supply plug from the power outlet and wait for the
machine to cool down before starting any maintenance or cleaning
operations.
The machine is intended exclusively for dispensing hot drinks through the use
of suitable granulated soluble products.
Do not make any changes, and do not use the machine improperly or for a
purpose different from the one for which it was designed.
• Do not use the machine when one or more components are damaged or
missing (power supply cable, plug, switches, etc.). Get the machine to be
checked or repaired at the nearest service centre.
• The use of accessories that are not recommended by the manufacturer
can cause damage to persons or things.
• Do not immerse the machine in any kind of liquid; do not clean it with
any strong detergents. It is sufficient to use a soft cloth soaked in
warm water.
• To avoid short-circuits and/or electric shocks keep away from the
machine liquids that may accidentally be spilled over the machine.
INSTALLATION
After opening the packing ensure that the machine is intact and check that all
of the main parts are included (refer to the figures in the following pages).
Plastic bags, polystyrene, nails etc. are potential sources of danger, therefore
they must not be left unattended or within the reach of children.
The machine must be positioned on a level, solid and stable surface, away from
heat sources. Ensure a free space at the sides and at the back of the machine
of at least 20 cm.
There must be sufficient free space to allow the operator to have access
to the machine in the event of malfunctions.
In case of doubt or should the instructions in this manual not be clear enough, do
not hesitate to ask for clarification from the supplier, an authorised service centre
or directly from the manufacturer.
Choose a hygienic and well lit room with an easy to access power outlet.
• Check that the power supply voltage of the machine
is the same as the one of the power supply outlet.
•The power supply outlet must be conforming to the plug of
the machine, sized to meet the characteristics indicated
on the data plate of the machine and connected to an
efficient earth circuit.
4
- 3 -
•Check that the power supply cable is not damaged or defective. If
there is a problem, do not use the machine under any
circumstances. The power supply cable must be replaced by the
manufacturer or by one of its service centres.
CLEANING
Before starting any cleaning on the machine, ensure that it is switched off
and that the plug is unplugged.
Wait several minutes to allow the components to cool down.
Do not insert any objects in the holes of the machine.
Pay attention to the position of the cable during installation, it must
not be:
REPAIRS AND MAINTENANCE
-
-
-
-
-
-
-
a hindrance to persons or things
crushed, pressed or placed on sharp surfaces
bent forcefully
In the event of failures, defects, suspected defects or if the
machine is dropped, immediately unplug the plug from the power
outlet. Never start a defective machine.
Only the Authorised Service Centre or the Manufacturer can
make repairs.
placed near hot surfaces
immersed, or placed near water or other liquids
wound around itself when the machine is in operation
tampered with.
DANGER ASPECTS
It is important to ensure that no children can touch the machine!
• The machine can be dangerous for children and must be made
inaccessible to them. If not used or if left unattended, it must
be deactivated.
• Do not leave any materials used for packing the machine within
the reach of children.
• Do not insert any objects through the machine openings (Danger!
Electric current!).
• Do not touch the plug and the cable while the machine is in
operation; do not unplug by pulling the cable.
••The parts near the dispensing zone can be very hot. Caution!
Risk of burns from contact.
In the event of repairs that are not well made, we decline all
responsibility for any damage.
DISPOSAL
The directive WEEE (Waste Electrical and Electronic
Equipment) indicates that electrical and electronic
products must be disposed of separately from normal
urban waste and similar. The aim is to send the waste to
authorised waste disposal centres, for the purpose of
promoting ways of recovering or recycling.
The directive includes also the accessories, the power
supply cables, etc
To correctly dispose of these products, follow the regulations provided by
the municipal authority and/or request further information from your
dealer when purchasing a new product.
5
6
OPERATING INSTRUCTIONS
CONTROL PANEL
F03
F06
F09
1 Drip tray
The figure shows the F09,
which has 3 canisters. The
F06 and F03 versions differ
from this in number of
canisters, respectively 2 and
1
2 Cup support grille
3 Canister of product A
3 Canister of product B
3 Canister of product C
4 Door
5 Water level sensor
6 Water tank
7 Main switch
8 Control panel
7
8
PRELIMINARY OPERATIONS
Before inserting the plug and switching the machine on, remove the water
tank, thoroughly rinse it and fill it with fresh water.
• As indicated in the figures of the previous page, the machines have 2
dispensing buttons for each granulated product:
-
-
Large cup: long dose
Small cup: short dose
Replace the tank, ensuring that the level sensor is immersed in the water.
Pour in the tank only fresh drinking still water. Hot water or other liquids
can damage the machine.
Do not start the machine without water; for correct dispensing, the softener
filter located at the end of the intake tube must be immersed completely.
In addition, they have a rinse button for each mixer unit installed.
The name assigned to the buttons in the figure (e.g. A1-A2), indicates the
name of the controlled mixer unit, A is the first one from the left.
YES
LOADING THE GRANULATED PRODUCT
IMPORTANT NOTICE:
The products dispensed by the machine with the appropriate mixing and
associations to the control panel are preset at the factory.
It is not possible to dispense different products from the ones for which the
machine is manufactured.
For machines equipped with more than one canister, make sure that each
product is located in the correct position.
Remove the canister, rinse it and dry it thoroughly. Pour the granulated
powder product, then fit the lid and replace the canister in its place. Verify
that the pin protruding from the base is inserted into the corresponding hole
of the machine.
9
STARTING THE MACHINE
N.B.: the machine requires little time for heating, if not
used in the immediate future, it is advisable to switch it off.
For correct dispensing, it
is important that the
product
inside
the
canister never falls below
this level.
After completing the preliminary operations, place a large enough container in
the drink dispensing point.
NOTE: the different configurations of the machine allow one or more
dispensing points.
Make sure the main switch is set to the position “0”
Insert the plug in the power outlet.
It is possible to understand if your model dispenses drinks in a single
point by the pattern on the grille, which has a sector with concentric
circles. On the contrary, the product will be dispensed under its own
mixer body.
It is important for the power outlet to
be compatible with the plug of the
machine and provided with the earth
connection pin.
Start the machine by pressing the main switch. After approximately 10
seconds, press the rinse button “L” to fill the machine internal circuit (if the
dispensing points are not grouped, make sure to press the rinse button
corresponding to the mixer body where the contained was placed).
Water coming out of the mixer spout means that the circuit is full.
Dispense at least two cups of water (it may be necessary to press the button
several times).
Never operate the machine without first filling the water circuit, not to
damage the heating element. If the water level in the tank is too low and
the water level sensor is not immersed, this will disable the electronic
card
.
11
12
Pay attention now, the display will indicate the message “READY -
SEL.PRODUCT“ and at this point it will be possible to dispense the desired
drink by pressing the corresponding button.
Periodically wash the water tank and replace the water.
Using a soft cloth damp with warm water, clean the outside of the softener
filter and the intake tube to which it is fitted.
INSTRUCTIONS FOR ROUTINE CLEANING
In order to keep the machine efficient and ensure a long lasting
duration, it is sufficient to take some simple precautions.
N.B.: The softener filter operates correctly up to 35 litres of water,
after which it must be replaced.
The machine will indicate on the display the end of the recommended filter
autonomy; after replacing the filter to reset the message, press and keep
pressed the rinse button of mixer A.
When switching the machine on, every now and then during the
course of the day and before switching it off, clean the mixer
by pressing the rinse button.
Clean the inside of the canister compartments.
Under no circumstances proceed by disassembling the machine.
Every day, at the end of the day,
disassemble the parts that compose
the mixer unit (‘X’, ‘Y’, ‘Z’, ‘K’, ‘J’ and
the internal plastic impeller ‘W’) and
therefore wash them with hot water.
DESCALING
Periodically it may be useful to descale the circuit using a specific product for
coffee machines, of the NON TOXIC type. Normally available in major
stores.
Warning! Under no circumstances use vinegar for descaling.
After using the product, thoroughly wash the water tank and rinse the circuit
by dispensing water only continuously, using a few times the maximum capacity
of the water tank.
The figure is only an example;
the shape of the elements may
vary according to the product
to be mixed.
13
14
TROUBLE-SHOOTING
• The machine dispenses too little water:
replace the resin filter fitted on the water intake tube and located
inside the water tank.
• The machine dispenses one drink and then stops:
check the water level in the tank and if necessary refill it or verify
that the shut-off valve is open.
• The powder is not dispensed:
check that the product canister is correctly inserted in its seat
and/or there is sufficient product.
• There is a water leak between component Z and its connection P in the
machine:
check that the component Z is inserted correctly.
• When pressing buttons A or B the product is not dispensed:
the operating temperature has not been reached yet, wait a few
minutes.
15
|