Krups Espresso Vivo User Manual

KRU PS  
Model  
Espresso Vivo  
Instructions  
for Use  
Warranty  
Guarantee of  
Performance  
IMPORTANT SAFEGUARDS  
When using electrical appliances, basic safety  
precautions should always be followed to reduce the  
risk of fire, electric shock, and/or injury to persons,  
including the following:  
Read all instructions and information in this  
instruction book and any other literature included in  
this carton referring to this product before operating  
or using this appliance.  
Do not touch hot surfaces. Use handles or knobs.  
To protect against fire, electric shock and personal  
injury do not immerse cord, plugs, or appliance in  
water or other liquid.  
Close supervision is necessary when any appliance is  
used by or near children.  
Unplug from outlet when not in use and before  
cleaning. Allow to cool before putting on or taking off  
parts, and before cleaning the appliance.  
Do not operate any appliance with a damaged cord or  
plug or after the appliance malfunctions, or has been  
damaged in any manner. Return appliance to your  
nearest authorized KRUPS Service Center for  
examination, repair or adjustment, or call KRUPS  
Consumer Service Department (see GUARANTEE OF  
PERFORMANCE) for repair procedure.  
The use of accessory attachments not recommended  
or sold by KRUPS may result in fire, electric shock or  
personal injury.  
Do not use outdoors.  
Do not let cord hang over edge of table or counter, or  
touch hot surfaces.  
Do not place on or near a hot gas or electric burner, or  
in a heated oven.  
Always attach plug to appliance first, then plug cord  
into the wall outlet. To disconnect, turn any control to  
“off“, then remove plug from wall outlet.  
This appliance is for household use only.  
Any servicing other than cleaning should be  
performed by your local authorized KRUPS Service  
Center.  
Appliances with Glass Containers.  
A. The container is designed for use with this appliance.  
It must never be used on a range top.  
B. Do not set a hot container on a wet or cold surface.  
C. Do not use a cracked container or a container having  
a loose or weakened handle.  
D. Do not clean container with cleansers, steel wool  
pads, or other abrasive material.  
SAVE THESE INSTRUCTIONS  
CAUTION  
This appliance is for household use. Any servicing other  
than cleaning and user maintenance should be  
performed by the nearest authorized KRUPS Service  
Center (see Guarantee of Performance).  
Do not immerse base in water.  
To reduce the risk of fire or electric shock, do not  
remove the base. No user  
parts inside. Repair  
should be done by an authorized KRUPS Service Center  
only.  
SPECIAL CORD SET INSTRUCTIONS  
Regarding your cord set:  
A. A short power-supply cord is provided to reduce risks  
resulting from becoming entangled in or tripping  
over a longer cord.  
B. Longer extension cords are available and may be  
used if care is exercised in their use.  
C. If a long extension cord is used,  
the marked  
electrical rating of the extension cord should be at  
least as great as the electrical rating of the appliance,  
(2) if the appliance is of the grounded type, the  
extension cord should be a grounding-type 3 wire  
cord, and (3) the longer cord should be arranged so  
that it will not drape over the counter top or table  
top where it can be pulled on by children or tripped  
over.  
D. This appliance has a polarized plug (one blade is  
wider than the other). As a safety feature, this plug  
will fit in a polarized outlet only one way. If the plug  
does not fully fit in the outlet, reverse the plug.  
If it still does not fit, contact a qualified electrician.  
Do not attempt to defeat this safety feature.  
Krups Espresso Vivo  
k
m
n
a: Hinged water chamber lid  
b: Removable water reservoir  
c: Steam knob  
d: Water level indicator  
e: Steam nozzle  
Removable drip tray  
Pump switch  
k: Thermostat indicator (yellow)  
ON/OFF indicator (red)  
m: ON/OFF switch  
n: Cord storage  
o: 1 and 2 cup filter baskets  
Perfect Froth attachment  
g: Filter holder  
h: Removable overflow grid  
Measuring spoon  
16  
Your “Espresso  
for the First lime  
Features  
Pump Espresso System  
features a stainless steel pump/boiler that  
that will make cup after cup of authentic,  
crema-laden espresso.  
n
n
We recommend that you get familiar with  
all the parts of your “Espresso Vivo” before  
operating the machine. Insert filter holder  
into the machine and remove and replace  
the water reservoir. Wipe off the steam  
nozzle and “Perfect Froth” attachment with a  
damp cloth to make sure all dust particles  
from transport are removed. Wash all loose  
parts in warm, soapy water, rinse  
Ready Light Thermostat Indicators  
lets you know when the machine is in use  
and when it has reached the proper  
brewing temperature.  
34 oz. Water Reservoir  
large capacity water container is easy to  
fill for continuous cups of espresso,  
cappuccino and lattes.  
thoroughly and dry.  
When using your “Espresso Vivo” for the  
first time we recommend running water  
through the machine to remove any dust  
particles that may have settled during  
shipping.  
n
“Perfect Froth” Attachment  
effortlessly produces froth for luscious  
cappuccino and lattes.  
Steam Nozzle  
Make sure before you start that the  
removable overflow grid is properly in place  
and that the drip tray is properly inserted.  
Before plugging the appliance into an  
electrical outlet, make sure that the pump  
switch is in the 0 position.  
for frothing, steaming and heating of  
other hot beverages.  
n
n
n
Water Level Indicator  
easily lets you monitor how much water  
is in the reservoir.  
One Two Cup Filter Baskets  
allows you to brew either one or two  
cups of rich, authentic espresso.  
Before First Use Cleaning the Internal  
System  
Removable Drip Tray and Grid  
large capacity drip tray and grid are easy  
to remove and clean.  
Before using your “Espresso  
for the  
first time, as well as after a long period of  
non-use, you will need to prime the machine  
for optimal performance. This requires  
running several cups of water through the  
system (without espresso). To prime the unit:  
Introduction  
Your new KRUPS “Espresso Vivo” features  
the latest in espresso technology and the  
most sophisticated features.  
Step 1  
n
Open the water chamber lid and remove  
the water reservoir figure  
Your new “Espresso Vivo” is another one of  
KRUPS finest espresso makers that is now  
available to you for at home use.  
This allows you to conveniently bring the  
water reservoir to the faucet.  
n
Fill the water container with fresh  
cold water just below the hinge of the  
handle (see figure  
n
Insert the water container back into the  
appliance (see figure  
Make sure that it sits in properly so the  
valve on the base of the water reservoir is  
activated. The front view water level  
indicator tells you how much water you  
have added.  
Step 2  
Insert the filter holder (without espresso)  
into the brewing head. Do this by raising  
the filter holder up into the machine at a  
45 degree angle (figure 4).  
Espresso is a far richer and stronger brew  
than regular coffee. It should be deep, dark  
and delicious. Most people find they enjoy it  
in small quantities because of its richness  
and for that reason, espresso is usually  
Place at least a 5 oz. cup directly under  
the filter holder (see figure 5).  
served in small  
oz. demitassse cups.  
n
Make sure the pump switch is in the ‘off”  
position. Using the ON/OFF button, turn  
The mark of real espresso is its wonderful  
inviting fragrance and a light brown  
“Crema”, found on top of the surface of the  
coffee. Your “Espressso Vivo”, properly  
used, will always produce espresso that is  
deep, dark, and delicious. Just follow the  
instructions and use fresh, well roasted  
espresso beans.  
“on” the appliance  
fig. 6  
The two indicator lights, yellow and red, will  
illuminate. Some water may drip out of the  
brewing head during the heating period.  
This is normal.  
n
Set the pump switch to the  
(see figure 6).  
position  
This will activate the pump. Upon first use,  
the boiler will need to intake water  
into the boiler chamber, and You will hear a  
distinct initial thumping noise.  
If you choose to grind your own beans we  
recommend using the KRUPS II Barista  
As soon as water is released from the filter  
holder, turn the pump switch back to the  
“off” position to allow the unit to reach the  
proper temperature.  
Remember, espresso requires a much finer  
grind than regular coffee. We recommend  
grinding your espresso beans for  
approximately 60 seconds; or until it has a  
talcum powder appearance and texture.  
Step 3  
As soon as the yellow (thermostat) light  
goes out, the machine is properly heated  
and ready for use.  
Set the pump switch to the  
position  
Before you make Your first cup of delicious  
espresso, make sure that the boiler chamber  
has water.  
and let water run into cup, stopping and  
starting water flow by using the pump  
switch (see figure 9).  
With the water reservoir full, place a cup  
directly under the filter holder. Turn “on” the  
Repeat this process until half of the water in  
the water reservoir has been used.  
unit and set the pump switch to  
As soon  
This will require you to stay with the  
machine to empty each cup as it becomes  
full. Upon completion of each cup set pump  
switch to the “off” position.  
as water begins to flow from the filter  
holder, the boiler is full. Set the pump  
switch back to the ‘off’ position. When the  
yellow thermostat light goes off, you are  
ready to make espresso.  
Making Espresso  
Step 1  
n
Fill the water reservoir with fresh, cold  
water (figures I-3).  
While making espresso, water can be added  
to the reservoir by opening the hinged  
water chamber lid and adding water to the  
10  
water reservoir, using another receptacle to  
fill the container.  
If you are preparing more than one cup of  
espresso, be sure to position two cups  
under the brewing spouts. When preparing  
cappuccino you will need a cup that has at  
least a 5 oz. capacity.  
CAUTION: the water reservoir is  
empty and the pump is running, you  
will hear a very distinct noise, which is  
louder than the normal operating  
sound. If this happens, turn the  
n
As soon as the yellow thermostat light  
goes out, set the pump switch to the  
figure 15).  
machine off. Check water reservoir and  
refill as needed. Never let the pump  
run when the water reservoir is empty,  
as this can damage the pump.  
When the desired amount of espresso has  
been brewed, turn the pump switch back to  
the off position. Remove the cup from under  
the filter holder.  
To remove the coffee from the filter basket,  
remove the filter holder from the machine  
by grasping the filter holder and turning to  
the left, until it dislodges.  
Step 2  
n
Set the pump switch to the “off” position  
and turn the unit “on” (figures 6 7).  
Dispose of used coffee in a waste  
Both indicator lights will illuminate. When  
the yellow indicator light goes out, the unit  
is ready for use.  
receptacle (see figure  
using the  
thumb guard to hold the filter basket in  
place.  
Reinsert the empty filter holder back into the  
machine to keep it warm.  
Remove the filter holder from the  
appliance. Choose the desired filter  
basket which is required for making one  
or two cups of espresso and insert into  
filter holder (see figure 10).  
If you wish to continue making espresso,  
disregard the yellow thermostat light. It  
simply indicates that the thermostat is  
regulating the temperature.  
Depending on which filter basket you have  
chosen, add one measuring spoon of  
espresso coffee for each cup of espresso  
that you are preparing (figure  
In addition to preparing espresso, you can  
also use your “Espresso Vivo” to froth milk  
-The one cup filter basket only requires  
one KRUPS measuring spoon of espresso  
coffee.  
for cappucino.  
reportedly takes  
its name from the chocolate hues of the  
robes worn by the Capuchin monks who  
favored this delicious desert coffee. While  
cappuccino is traditionally made up of  
espresso and frothed milk, it can be tailored  
to one’s own taste with cinnamon, sugar,  
chocolate flakes, or even liquor. Its  
versatility makes cappucino a world-wide  
gourmet choice.  
-The two cup filter basket only requires  
two KRUPS measuring spoons of  
espresso coffee.  
Gently press (tamp) the coffee into the  
filter holder using the bottom of the  
measuring spoon (see figure  
and  
ensure that any loose coffee remaining  
on the outer edges are removed (see  
figure  
As long as your “Espresso Vivo” is turned  
on and the water reservoir is properly filled,  
you can use the steaming feature. There is  
no need to prepare espresso before using  
this steaming feature.  
Insert the filter holder back into the  
machine by raising it up at a 45 degree  
angle and turning it to the right, until  
the filter holder is locked into place  
(see figure 14).  
For best results, you should use the “Perfect  
Froth” attachment.  
Place a cup which has at least a 2-2.5 oz.  
capacity underneath the filter holder spout.  
11  
NOTE:  
n
If it is not in place, attach it now  
figure 17).  
Do not bring milk to a boil (this will happen  
if large bubbles start forming at the surface  
of the milk).  
KRUPS “Perfect Froth” attachment lets you  
froth milk perfectly for making cappuccino.  
Do not let the “Perfect Froth” attachment  
touch the bottom of the pitcher. This will  
prevent you from frothing.the milk.  
Frothing Milk for  
Cappuccino  
Step 1  
Step 4  
After the milk is frothed, keep the “Perfect  
Froth” in the milk until the steam knob has  
been turned to the position. This will  
prevent any splattering from  
The first step in making  
is to  
make espresso. See section “Preparing  
Espresso”. When preparing cappuccino use  
a cappuccino cup which has a capacity of at  
least 5 oz. You should fill the cup  
with espresso.  
After milk is frothed, set aside. If you like  
very stiff froth, let the pitcher set for a few  
seconds.  
way  
n
Make sure that the pump switch is in the  
0 position (see figure 18).  
Now you are ready to add the frothed milk  
to the already prepared espresso. Pour the  
milk into the cup by holding back the froth  
with your spoon. Fill the remainder of the  
cup with the hot milk and then spoon on the  
froth. In Italy cappuccino is normally one  
part espresso to two parts milk plus froth.  
Step 2  
Take a stainless steel frothing pitcher and fill  
it  
aside. This amount of milk will yield enough  
froth for two cups of cappuccino. If you  
need more froth, repeat these steps.  
to  
full with fresh, cold milk and set  
If  
making more than one or two  
cups of cappuccino, it is recommended that  
you place the finished espresso on top of  
the warming plate with a cloth or saucer  
covering the cups. This will help to keep the  
espresso hot.  
We recommend using skim or 2% milk if  
you prefer a stiff, dense froth. Use regular  
milk if you prefer a creamier type of froth.  
NOTE:  
Attention:  
When you start frothing milk, there will be a  
thumping sound which occurs during the  
steam preparation. This results from the  
interval controlled water pump condensing  
water into steam.  
n
The top closure of the “Perfect Froth”  
attachment figure 22, part has a  
very fine hole which draws air into the  
milk.  
If this tiny hole gets clogged, “Perfect Froth”  
will not work properly. Therefore, never  
immerse the top closure in milk or froth.  
As the thumping sound begins a few drops  
of water will come out of the steam nozzle  
before entirely changing over to steam.  
If you wish to prepare espresso immediately  
after using the steam nozzle, the machine  
must be cooled down to the proper brewing  
temperature. (When frothing milk, the  
temperature of the water is much hotter  
than when you are brewing espresso.)  
Step 3  
n
When the yellow thermostat light goes  
out, insert the steam nozzle half way into  
the milk and turn the steam knob slowly  
to the max position (see figure  
In order that you do not burn your next  
batch of espresso, insert the clean filter  
holder into the machine and set the pump  
Leave the steam nozzle in the milk for  
approximately 45-60 seconds, depending on  
how much froth you want and the type of  
milk you are using.  
switch to  
Allow  
cup of water to run  
through the machine.  
1 2  
All parts should be rinsed in warm, soapy  
water. If the small section of part A is  
clogged, it can be opened using a fine  
sewing needle.  
This process cools the machine sufficiently  
to prepare additional cups of espresso.  
Use caution when removing the “Perfect  
Froth” from the steaming nozzle as it may  
still be hot.  
Heating Liquids  
The steam nozzle can also be used to heat  
liquids, without frothing, such as tea and  
instant soup. To heat liquids:  
Use a damp cloth to clean the steam nozzle.  
Use caution when cleaning or removing the  
steaming nozzle as it may still be hot.  
Set the pump switch to the off position.  
Swing out the steam nozzle and remove the  
“Perfect Froth” attachment  
Make sure there is enough water in the  
water reservoir  
Cleaning the Machine  
n
After preparing espresso five times, the  
drip tray and grid may need to be  
emptied and cleaned (see figure 20).  
Turn the unit “on”. Initially, a small amount  
of water and steam will emerge from the  
steam nozzle.  
The water reservoir, drip tray, baffle grid,  
filter holder, and “Perfect Froth” attachment  
should be washed and rinsed in warm,  
soapy water on a regular basis.  
As soon as the yellow thermostat light goes  
out, place the cup or container under the  
steam nozzle. Turn the steam knob slowly to  
the max position.  
The warming tray can be removed and  
wiped with a damp cloth for easy cleaning.  
Once liquid is heated, slowly return the  
steam knob back to the position and  
remove the cup from under the steam  
nozzle.  
Do not place any loose pieces in the  
dishwasher.  
NOTE:  
IMPORTANT:  
Clean the steam nozzle each time you have  
immersed it in milk, otherwise the inside of  
the nozzle becomes clogged with milk  
particles. Allow the steam to escape into a  
wet cloth for one or two seconds after  
frothing milk. This will flush out any milk  
residue.  
If you wish to prepare espresso immediately  
after using the steam feature, it is essential  
to allow the machine to adjust to the proper  
temperature. Insert the empty filter holder  
and place a cup directly underneath. Turn  
the pump switch to the  
position and  
allow water to run through until the yellow  
thermostat light illuminates. Return the  
pump switch to the off position and prepare  
espresso.  
CAUTION: Do not try to disassemble  
the main body of the machine.  
If necessary, the steam nozzle can be  
removed using the hexagonal key located  
on the measuring spoon (see figure 21).  
Cleaning the Perfect Froth  
Attachment  
When replacing, do not overtighten.  
Do not attempt this while steam nozzle is  
hot.  
It is strongly advised that you wipe off the  
milk residue which may have collected on  
the “Perfect Froth” and steaming nozzle  
after the frothing process is completed.  
n
For a thorough cleaning of the “Perfect  
Froth” attachment, remove the separate  
parts A, B, C (see figure 22).  
1 3  
No elasticity in the brewing head seal.  
(This may happen after a long period of  
use). This part can be ordered through  
KRUPS Consumer Service Department.  
Under normal conditions you do not need to  
decalcify your “Espresso Vivo”. However, in  
areas where there is hard water or if you  
use your machine very frequently we  
recommend decalcifying. You will know  
when such a cleaning is necessary by an  
obvious slow down in the brewing time.  
is widely available and can be  
If the seal has lost its elasticity, it must be  
replaced with a new one. Allow the  
appliance to cool down and then unscrew  
the sieve from the brewing head.  
Remove the seal carefully from the  
brewing head using a screw driver.  
purchased through KRUPS Consumer  
Service Department.  
Place the new seal onto the machine and  
then place the flattened side of the sieve  
back into brewing head.  
How To Decalcify  
n
Before beginning, it is necessary to  
remove the strainer from the brewing  
head (see figure 23).  
Problem:  
Pump makes loud noise.  
Cause:  
This can be done using a flat head screw  
driver.  
No water in the water reservoir.  
n
Old or dry coffee is being used, water  
cannot properly flow through the coffee.  
Remove the water reservoir and fill it with  
luke warm water. Dissolve the decalcifying  
solution into the water reservoir. Replace  
the water reservoir.  
Problem:  
Coffee does not come out of filter holder.  
Place a cup underneath the brewing spout.  
Cause:  
Set the pump switch to the  
position.  
No water in the water reservoir.  
Stop between each cup and empty it as it  
becomes full. Proceed with this until all of  
the water has run through the machine.  
Allow the appliance to cool for  
n
n
Water reservoir not inserted correctly.  
Filter blocked because the coffee mixture  
is too fine or has been tamped too hard.  
minutes when done.  
Machine needs to be decalcified.  
To eliminate traces of the decalcifying  
solution, fill the water reservoir with fresh,  
cold water.  
Problem:  
Espresso has no “Crema”.  
Continue this process until there is no more  
water in the reservoir.  
Cause:  
n
n
Old or dried out coffee being used.  
Coffee not suitable for espresso.  
Coffee ground too coarsely.  
n
Too little coffee in the filter or not  
properly tamped.  
Problem:  
Coffee leaking from filter holder.  
Cause:  
Problem:  
n
Filter holder not properly inserted in the  
machine.  
Not enough froth when frothing milk.  
Cause:  
n
Filter holder not pushed in as far as it  
will go.  
n
n
Steam nozzle is clogged.  
Milk is not fresh.  
14  
The pitcher that you are using is not  
is recommended that you use  
a stainless steel frothing pitcher.)  
Cold conducts better to metal than to  
glass or plastic.  
The type of milk is not suitable.  
We recommend using 2% or skim milk.  
Whole milk is acceptable, but due to the  
fat molecules, it will not have as dense a  
froth, as if you were to use 2% or skim  
milk.  
Your KRUPS  
is covered by the  
following warranty:  
If from date of purchase within one year this  
KRUPS product fails to function because of  
defects in materials or workmanship,  
KRUPS North America will, at its option,  
repair or replace the unit without charge,  
provided the owner has a proof of date of  
purchase.  
This warranty will be void if malfunction  
was caused by damage to the product by  
accident, misuse, use on frequency or  
voltage other than marked on the product  
and/or described in the instructions, abuse  
including tampering, damage in transit, or  
use for commercial purposes. This warranty  
gives you specific legal rights, and you may  
also have other rights which may vary from  
state to state.  
GUARANTEE OF-PERFORMANCE  
This fine KRUPS product is manufactured according to a rigid  
code of quality standards, and, with minimum care, should  
give years of satisfying service. However, should the need  
arise for repairs or for replacement parts within or after the  
please call our CONSUMER SERVICE  
DEPARTMENT:  
(800) 526-5377  
a day, 7 days a week  
You will be provided with specific instruction on how to get  
your product repaired, as well as the name and address of your  
nearest authorized KRUPS Service Center. The department will  
also be able to answer any general product questions you may  
have.  
Before calling the Consumer Service Department, please have  
the type number of your KRUPS appliance available.  
You must have this information before calling our Consumer  
Service Department so that we may better answer your  
questions. The type number can be located by looking at the  
bottom of your appliance.  
This product is Type  
Any general  
can be addressed to:  
KRUPS North America, Inc.  
P.O. Box 3900  
Peoria, IL 61612  

Motorola BACKFLIP 68000202889 User Manual
Lenoxx Electronics CR 500 User Manual
HP Hewlett Packard HP iPAQ rw6800 User Manual
Hitachi Deskstar HDS721016CLA382 User Manual
Harman Kardon HD 990 User Manual
Echo Bear Cat CH8540 User Manual
Capresso 156 User Manual
Black Box Computer Accessories LBLPO1A KIT User Manual
Addonics Technologies PUDDESP User Manual
3Com SP 510UZ User Manual