Keurig Inc Coffeemaker B150 User Manual

B150 Series Commercial Brewer  
Direct Plumb Kit  
Welcome Keurig Authorized Dealer!  
This manual provides:  
Installation of the Direct Plumb Kit (DPK) that allows you to connect your  
customer’s B150 brewer to municipal or independently pumped water supply.  
Maintenance Mode diagnostics that will provide you with system information and  
tools so that you can fully diagnose any problems at the customer’s site.  
Instructions on how to descale the brewer in the event of problems associated  
with hard water.  
P/N 60-201142-000 Rev A 10/09  
5. On the side of the brewer locate the Connector Cover. Remove and reserve the  
screw. Remove the Connector Cover and expose DPK Interface Connector.  
FIGURES 5 & 6  
FIGURE 5  
FIGURE 6  
6. Make the electrical connection between the DPK CWT and the brewer body. The  
Connector Cover has an alternate position that allows for cable exit and  
reattachment to the Brewer Body. FIGURES 7 & 8  
FIGURE 7  
FIGURE 8  
7. Install DPK and secure to Brewer Base using the 2 screws that were previously  
used for the Connection Access Plate. FIGURE 9  
FIGURE 9  
8. The B150 Direct Plumbed Unit is now ready to be connected to AC Power and  
filtered water supply in accordance with local Building Code rules and  
regulations.  
3
Filter Requirements  
The Keurig B150 brewer system, when used with Direct Plumb accessory,  
requires the use of a water filtration system to optimize the coffee flavor and  
brewer reliability. Two mounting holes with screws have been provided on the  
back of the brewer for this purpose.  
Keurig requires the use of an external water filter such as the Omnipure  
KQ8A to maintain warranty.  
A filter kit (part number 5025) is available from Keurig. This kit contains a  
Omnipure KQ8A filter, filter head, and mounting bracket.  
NOTE: The KQ8A Filter assembly comes with 1/4 FPT ports for both inlet and  
outlet and the plumbed water inlet to the brewer is 3/4 Male Garden Hose Thread  
1/4 OD LLDPE (Linear Low Density Polyethylene) tubing is recommended (NSF  
compliant) between the filter assembly and the brewer. NSF compliant fittings are  
recommended such as High Density Polypropylene Type.  
NOTE: NO PLUMBING CONNECTORS ARE PROVIDED WITH THIS  
KIT.  
All KQ8A filter cartridges must have a minimum of four gallons of water  
run through it after mounting to the brewer and before they are connected to  
the brewer’s Inlet Valve at the install location. This procedure will prevent  
fine particles of carbon from entering and clogging the water inlet valve.  
Filter Installation  
1. Attach a ¾” female garden hose connection to ¼” FPT fitting to the Inlet  
Valve  
2. Mount the filter assembly to the brewer using the screws provided on the back  
of the brewer and connect the filter’s Inlet Port to the water supply.  
3. Flush the filter BEFORE connecting to the Inlet Valve.  
4. Plug brewer into a dedicated GFCI outlet. If the electric circuit is overloaded  
with other appliances, the circuit breaker may trip. If possible, the brewer  
should be operating on its own circuit, separate from other appliances. Never  
use an extension cord.  
CAUTION: This brewer is designed to handle local water pressures from 40 psig up  
to 125 psig. Consult a licensed plumber for water pressures in your area. Use  
plumbing fittings and tubing specified to withstand 125 psig.  
IMPORTANT NOTICE  
NOTE: FAILURE TO USE A WATER FILTER OR FAILURE TO  
USE A WATER FILTER IN THE PRESCRIBED MANNER WILL  
INVALIDATE THE BREWER WARRANTY.  
4
Descaling Instructions for B150 Brewer with DPK  
Minerals in drinking water build up on hot surfaces and can build to a point where fluid  
flow is reduced and other normal brewer functions are hindered. When this occurs, the  
brewer must be cleared of these deposits to allow normal brewer function.  
Keurig recommends that the brewer be descaled every 6 months or as needed depending  
on use and/or local water supply mineral content. Symptoms of scale build up are slow  
brewing and/or short cups.  
The following procedure outlines the steps required to prepare the brewer for the addition  
of the descaling solution.  
1. Unplug the brewer from AC Power Supply.  
2. Disconnect or interrupt external water supply feeding the brewer.  
3. Drain the Hot Water and Cold Water Tanks using the drain tubes, marked H and  
C, located at rear of brewer per the draining procedure as shown below.  
4. At the rear, left, top of the brewer locate and remove two screws which will allow  
removal of the Top Cover and gain access to the internal Water Reservoir.  
Remove  
Screws  
5
5. After removal of Top Plate, the Descaling Solution Access Port in the Water  
Reservoir will be clearly evident as shown below.  
Pour  
Descaling  
Solution  
here  
6. Reconnect the brewer to AC Power Supply.  
7. Proceed with descaling procedure as defined below:  
De-Scaling Procedure  
Preparation:  
Prepare at least 40 ounces of a commercial citric acid descale solution. You will  
also need a large ceramic mug (a paper cup is not suitable for this procedure) and access  
to a sink for discarding hot liquid.  
FILL AND CLEAN  
1. Pour 40 ounces of descale solution into the Cold Water Tank through the Access  
Port shown above and turn on the brewer – the brewer will automatically fill and  
begin heating.  
2. When the brewer display shows “Ready To Brew” place the ceramic mug on the  
drip tray, select the largest brew volume, and press the Brew button  
NOTE: Do not use a K-Cup portion pack  
3. Once the solution begins to exit the brewer, lift the Brew Head Handle just  
enough to halt the brew process and let the brewer sit for 40 minutes in this state.  
6
4. At the end of the 40 minutes, lower the handle and the brewer should complete  
the brew (do not be concerned if the brewer does not complete the brew). Pour  
the dispensed liquid into the sink.  
5. Shut down the brewer, disconnect it from AC power, and drain both (Hot and  
Cold) water tanks using the drain tubes located in the back panel of the brewer.  
CAUTION: Hot water will be exiting from the Hot Water Tank  
6. Manually fill the Cold Water and allow to drain tank three times, using 40 ounces  
fresh water per fill. Replace Drain Tube Plugs and Access panel.  
7. Reconnect or resume city water supply and power up the brewer.  
8. Once the brewer is filled and hot, conduct large volume “Water Only” brews,  
with no K-cup potion pack in place, until all remnants of the descale solution are  
not longer evident discarding all liquids into the sink. We suggest using the  
largest brew size to speed the process. Remember to open and close the brew  
handle between each cycle so the blue Brew lights will flash.  
9. Place the brewer back into service.  
You may need to perform additional rinse cycles if you notice any residual taste.  
7
Draining Procedure for Hot Water Tank and DPK CWT  
This procedure is to be performed prior to transportation of unit and when converting  
brewer between Pour Over usage and Direct Plumb usage.  
NOTICE  
THIS PROCEDURE MAY RESULT IN THE RELEASE OF  
WATER AT TEMPERATURES HOT ENOUGH TO RESULT IN  
BURNS. DRAINING PROCEDURE SHOULD ONLY BE  
PERFORMED BY TRAINED SERVICE PERSONNEL.  
1. Disconnect the brewer from AC power and, if applicable, disconnect the Direct  
Plumb Unit from water supply.  
2. On rear of brewer locate Access Panel and remove securing screw.  
3. Lower the appropriate tube, remove Plug and drain into appropriate sized  
container. NOTE: Hot Water Tank contains ~ 31 oz of water, Cold Water Tank  
contains ~ 35 oz of water.  
4. Replace Plugs and Access Panel.  
Drain Tubes with Access Panel removed  
8
Maintenance  
Purpose  
This section describes the Maintenance Mode and key sequences for entry into this mode  
for the B150 Brewer.  
Maintenance Mode Layout  
Entry: From STANDBY, press all 4 corners of the touchscreen (Upper Left/Right and  
Lower Left/Right in any order) within 3 seconds, – releasing after each touch  
1. Screen 1 – “Software Version”  
2. Screen 2 – “Total Brew Count”  
Life])  
(e.g. “ v8.25”)  
(Max = 999,999 [25 x  
– “Postfill Timeouts”  
– “Add2 Timeouts”  
3. Screen 3 – “Add4 Timeouts”  
– “Add6 Timeouts”  
(Max = 65535)  
(Max = 65535)  
(Max = 65535)  
(Max = 65535)  
(Max = 65535)  
(Max = 65535)  
(Max = 65535)  
(Max = 65535)  
(Max = 999,999 [114  
– “Add8 Timeouts”  
4. Screen 4 – “Dispense Timeouts”  
– “Over-Pressure Events”  
– “Top of Tank Events”  
5. Screen 5 – “Run Hours”  
years])  
– “4 oz Brew Count”  
– “6 oz Brew Count”  
6. Screen 6 – “8 oz Brew Count”  
– “10 oz Brew Count”  
(Max = 65535)  
(Max = 65535)  
(Max = 65535)  
(Max = 65535)  
(Max = 65535)  
– “12 oz Brew Count”  
7. Screen 7 – (Buttons control Opening/Closing the Valve)  
Brew Button = Cont.  
8. Screen 8 – (Buttons control Turning Pump On/Off)  
Brew Button = Cont.  
9. Screen 9 – “Brew Pump”  
“Vent Valves”  
(Buttons control Brew Pump On/Off & Opening/Closing the  
Valve)  
10. Screen 10 – Touchscreen Calibration  
– Press Brew button to exit OR touch display to start calibration.  
– IF Cal Passes, exit. If it fails, give another opportunity to try  
– Exit back to the Standby State  
11.  
NOTE:  
Progress from screen to screen using the flashing Brew Button  
9

NETGEAR ReadyNAS 600B User Manual
NetComm Wireless Network Adaptor NP545 User Manual
Motorola H76XAH6JR7BN User Manual
Microsoft Word 5908400 User Manual
Memorex MSP CR1100 User Manual
JVC KD S50 User Manual
iHome IH B939NN User Manual
HP Hewlett Packard 40 SCSI User Manual
Addonics Technologies AE6CFHI User Manual
ABB CL3020 User Manual