CD-RECEIVER
KDC-X791
KDC-MP735U
KDC-MP635
INSTRUCTION MANUAL
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best
performance from your new CD-receiver.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the
warranty card, and in the space provided below. Refer to the model and serial numbers
whenever you call upon your Kenwood dealer for information or service on the product.
Model KDC-X791/MP735U/MP635 Serial number
US Residence Only
Register Online
Register your Kenwood product at
© B64-3625-00/00 (KW)
Safety precautions
• Use only the screws provided or specified for
installation. If you use wrong screws, you could
damage the unit.
2 WARNING
To prevent injury while using this
product, take the following safety
precautions:
Attach the panel while you are on the
vehicle
• To prevent a short circuit and possible fire, never
put any metallic objects (such as coins or metal
tools) inside the product.
The panel lock arm appears when the panel is
removed. Therefore, the panel must be attached while
the electrical system of the car is operating.
• If you are the driver and your vehicle is moving,
do not watch the product’s display or use its
controls for an extended period.
• Do not use this product in any way that prevents
you from driving safely.
Do Not Load 3-in. CDs in the CD slot
If you try to load a 3 in. CD with its adapter into the
unit, the adapter might separate from the CD and
damage the unit.
• Follow all driving laws and use common sense
when using this product.
About CD players/disc changers connected
to this unit
NOTE:
• Like your vehicle’s speedometer, G-Analyzer is
no more than a measuring function. The HP
or G value measured by this unit may not be
completely accurate due to its simplified method of
measurement. The G-Analyzer is only for reference
and should not be used to confirm the horsepower
specifications of your vehicle.
Kenwood disc changers/ CD players released in 1998
or later can be connected to this unit.
Refer to the catalog or consult your Kenwood dealer
for connectable models of disc changers/ CD players.
Note that any Kenwood disc changers/ CD players
released in 1997 or earlier and disc changers made by
other makers cannot be connected to this unit.
Connecting unsupported disc changers/CD players to
this unit may result in damage.
Set the "O-N" Switch to the "N" position for the
applicable Kenwood disc changers/ CD players.
The functions you can use and the information that
can be displayed may differ depending on the models
being connected.
• Mounting and wiring this product requires skills and
experience. For safety’s sake, leave the mounting
and wiring work to professionals.
2CAUTION
To prevent damage to the machine, take
the following precautions:
¤
• Make sure to ground the unit to a negative 12V DC
power supply.
•
You can damage both your unit and the CD changer if you
connect them incorrectly.
• Do not install the unit in a spot exposed to direct
sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of
water splashing.
• Do not place the faceplate (and the faceplate case)
in areas exposed to direct sunlight, excessive heat or
humidity. Also avoid places with too much dust or
the possibility of water splashing.
Lens Fogging
When you turn on the car heater in cold weather,
dew or condensation may form on the lens in the
CD player of the unit. Called lens fogging, this
condensation on the lens may not allow CDs to play.
In such a situation, remove the disc and wait for the
condensation to evaporate. If the unit still does not
operate normally after a while, consult your Kenwood
dealer.
• To prevent deterioration, do not touch the terminals
of the unit or faceplate with your fingers.
• Do not subject the faceplate to excessive shock, as it
is a piece of precision equipment.
• When replacing a fuse, only use a new fuse with
the prescribed rating. Using a fuse with the wrong
rating may cause your unit to malfunction.
• Do not apply excessive force to the open faceplate
or place objects on it. Doing so will cause damage
or breakdown.
iPod is a trademark of Apple Computer, Inc.,
registered in the U.S. and other countries.
The "AAC" logo is trademark of Dolby
Laboratories.
English
|
3
Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check with
your Kenwood dealer to make sure that they work
with your model and in your area.
• We recommend the use of <Activating Security
Code> (page 33) to prevent theft.
• The characters conforming to ISO 8859-1 character
set can be displayed.
Cleaning the Unit
If the faceplate of this unit is stained, wipe it with a
dry soft cloth such as a silicon cloth.
If the faceplate is stained badly, wipe the stain off with
a cloth moistened with neutral cleaner, then wipe it
again with a clean soft dry cloth.
¤
•
Applying spray cleaner directly to the unit may affect its
mechanical parts. Wiping the faceplate with a hard cloth or
using a volatile liquid such as thinner or alcohol may scratch
the surface or erases characters.
• There are places in this manual where lit indicators
are described; however, the only time an indicator
will light is in the following settings.
When Status Display is set to On as mentioned in
<Status Setting> (page 11).
Cleaning the Faceplate Terminals
If the terminals on the unit or faceplate get dirty, wipe
them with a clean soft dry cloth.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
Before using this unit for the first time
This unit is initially set on the Demonstration mode.
When using this unit for the first time, cancel the
<Demonstration mode setting> (page 40).
About KENWOOD "Music Editor" of PC
application attached to KDC-X791/MP735U
• "Music Editor" is recorded in the CD-ROM attached
to this unit.
How to reset your unit
• If the unit fails to operate properly, press the Reset
button. The unit returns to factory settings when the
Reset button is pressed.
• Remove the USB device before pressing the Reset
button. Pressing the Reset button with the USB
device installed can damage the data contained in
the USB device. For how to remove the USB device,
refer to <Playing USB (iPod) device> (page 24).
• Refer to the attached installation manual for the
installation method of "Music Editor".
• Refer to the user’s manual recorded in the
installation CD-ROM and Help of "Music Editor" for
the operation method of "Music Editor".
• Press the reset button if the disc auto changer fails
to operate correctly. Normal operation should be
restored.
• The unit can play CD/ USB device created by "Music
Editor".
• Information about "Music Editor" upgrade is put on
Reset button
|
4
English
About Audio file
About USB device
•
Playable Audio file
• Install the USB device in the place where it will not
prevent you from driving your vehicle properly.
AAC-LC (.m4a), MP3 (.mp3), WMA (.wma),
WAV (.wav) (KDC-X791/MP735U only)
• You cannot connect a USB device via a USB hub.
•
•
•
•
Playable disc media
CD-R/RW/ROM
Playable disc file format
ISO 9660 Level 1/2, Joliet, Romeo, Long file name.
Playable USB device (KDC-X791/MP735U only)
USB mass storage class, iPod with KCA-iP200
Playable USB device file system (KDC-X791/
MP735U only)
• Take backups of the audio files used with this unit.
The files can be erased depending on the operating
conditions of the USB device.
We shall have no compensation for any damage
arising out of erasure of the stored data.
• No USB device comes with this unit. You need to
purchase a commercially available USB device.
• For how to play the audio files recorded in a USB
device, see <CD/USB device/Audio file/External disc
control features> (page 23).
FAT16, FAT32
Although the audio files are complied with the
standards listed above, the play maybe impossible
depending on the types or conditions of media or
device.
• When connecting the USB device, usage of the CA-
U1EX (option) is recommended.
Normal playback is not guaranteed when a cable
other than the USB compatible cable is used.
Connecting a cable whose total length is longer
than 5 m can result in abnormal playback.
•
Playing order of the Audio file
In the example of folder/file tree shown below, the
files are played in the order from ① to ⑩.
<
v
:
:
Follder
Audiofile
CD
(ꢂ)
About Satellite Radio tuner
This unit supports Satellite Radio tuners which are
released by SIRIUS and XM.
vꢀ
ꢁ
Refer to the instruction manual of Satellite radio tuner.
ꢃ
vꢆ
vꢇ
ꢅ
About Bluetooth Hands free control
Refer to the instruction manual of the Bluetooth
Hands Free Box KCA-BT100 (optional accessory).
vꢄ
ꢈ
vꢉ
v.
About Menu operation
For how to operate Menu, refer to <Menu System>
in this instruction manual. For the items to be set
up, refer to the instruction of Hands Free Box.
About display of Cell-Phone Status
Cell-Phone Status is displayed in the status display
of this unit. For the information about the displayed
An online manual about audio files is put on the
manual, detailed information and notes which are not
written in this manual are provided. Make sure to read
through the online manual as well.
⁄
•
In this manual, the word "USB device" is used for flash
memories and digital audio players which have USB
terminals.
•
The word "iPod" appearing in this manual indicates the iPod
connected with the KCA-iP200 (optional accessory). The
iPod connected with the KCA-iP200 can be controlled from
this unit. iPods that can be connected with the KCA-iP200
are the iPod nano and the iPod with video. When an iPod
is connected using a commercially available USB cable, it is
handled as a mass-storage-class device.
•
For the supported formats and types of USB device, refer to
English
|
5
Notes
Handling CDs
2CAUTION
• Do not touch the recording surface of the CD.
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
In compliance with Federal Regulations, following
are reproductions of labels on, or inside the product
relating to laser product safety.
• Do not stick tape etc. on the CD, or use a CD with
tape stuck on it.
• Do not use disc type accessories.
• Clean from the center of the disc and move
outward.
• When removing CDs from this unit, pull them out
horizontally.
• If the CD center hole or outside rim has burrs,
use the CD only after removing the burrs with a
ballpoint pen etc.
Kenwood Corporation
2967-3, ISHIKAWA-MACHI,
HACHIOJI-SHI
TOKYO, JAPAN
KENWOOD CORP. CERTIFIES THIS EQUIPMENT
CONFORMS TO DHHS REGULATIONS N0.21 CFR
1040. 10, CHAPTER 1, SUBCHAPTER J.
CDs that cannot be used
• CDs that are not round cannot be used.
Location : Bottom Panel
FCC WARNING
This equipment may generate or use radio
frequency energy. Changes or modifications to this
equipment may cause harmful interference unless
the modifications are expressly approved in the
instruction manual. The user could lose the authority
to operate this equipment if an unauthorized change
or modification is made.
• CDs with coloring on the recording surface or CDs
that are dirty cannot be used.
• This unit can only play the CDs with
.
This unit may not correctly play discs which do not
have the mark.
• You cannot play a CD-R or CD-RW that has not been
finalized. (For the finalization process refer to your
CD-R/CD-RW writing software, and your CD-R/CD-
RW recorder instruction manual.)
NOTE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment may cause harmful interference to radio
communications, if it is not installed and used in
accordance with the instructions. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
|
6
English
General features
ATT
VOL
Release button
FNC
SRC Control knob
ATT indicator
Function icon
Power
Source required
Display
"SAT"
Satellite radio (Optional accessory)
Tuner or HD Radio (Optional accessory)
USB device (iPod)*
Turning ON the Power
Press the [SRC] button.
"TUNER" or "HD Radio"
"USB" ("iPod")
"Compact Disc"
"CD Changer"
"AUX"
CD
Turning OFF the Power
Press the [SRC] button for at least 1 second.
External disc (Optional accessory)
Auxiliary input*
Auxiliary input (Optional accessory)
Standby (Illumination only mode)
"AUX EXT"
"STANDBY"
⁄
Selecting the Source
There are two types of source selection methods
depending on the setting.
•
•
* Function of KDC-X791/MP735U.
When connection of the iPod is recognized, the source
display changes from "USB" to "iPod".
Switch between SRC Select mode 1 and 2 in <Source
Select Mode> (page 34).
•
•
SRC Select mode 1:
1 Press the [SRC] button.
USB (iPod) source is recognized as CD source on the
connected unit.
2 Turn the Control knob or push it towards left or
right.
3 Press the Control knob.
SRC Select mode 2:
Press the [SRC] button.
English
|
7
General features
* You can adjust these items in detail. Refer to <Adjusting
the detail of Audio Control>(Page8). (Function of KDC-
X791)
* Source tone memory: Puts the set up value in the
memory per source. (Detail Audio item is included)
Volume
Increasing Volume
Turn the [VOL] knob clockwise.
Decreasing Volume
Turn the [VOL] knob counterclockwise.
⁄ About System Q
•
You can recall the best sound setting preset for different
types of music.
•
Change each setting value with the <Speaker Setting>
(page 10). First, select the speaker type with the Speaker
setting.
Attenuator
Turning the volume down quickly.
•
"USER": The ranges selected lastly for Bass level, Middle
level, and Treble level are recalled automatically.
Press the [ATT] button.
Each time you press the button, the Attenuator
turns ON and OFF.
When the Attenuator is ON, the "ATT" indicator
blinks.
5 Exit Audio Control mode
Press any button.
Press a button other than the [VOL] knob and [ATT]
button.
Function of KDC-X791
Audio Control
Adjusting the detail of Audio Control
Among the Basic Audio items, you can adjust the Bass
level, Middle level, and Treble level in detail.
1 Select the source to adjust
Press the [SRC] button.
Refer to <Selecting the Source> (page 7).
1 Select the Basic Audio item
Select the desired item to be set in detail from
followings;
2 Enter Audio Control mode
Press the [VOL] knob.
• Bass level
• Middle level
• Treble level
For how to select Basic Audio items, see <Audio
Control> (page 8).
3 Select the Basic Audio item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
2 Enter Detail adjustment mode of Audio
Control
Press the [VOL] knob for at least 1 second.
4 Adjust the Basic Audio item
Turn the [VOL] knob.
Adjustment Item Display
Range
0 — 35
–15 — +15
User/Rock/
Pops/Easy/
Top 40/Jazz/
Natural
–8 — +8
–8 — +8
–8 — +8
Left 15 — Right 15
Rear 15 — Front 15
3 Select the Detail Audio item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
Rear Volume
Subwoofer level
System Q
"REAR VOLUME"
"SUB-W LEVEL"
"USER"/"ROCK"/
"POPS"/"EASY"/
"TOP40"/"JAZZ"/
"NATURAL"
4 Adjust the Detail Audio item
Bass level*
Middle level*
Treble level*
Balance
"BASS LEVEL"
Turn the [VOL] knob.
"MIDDLE LEVEL"
"TREBLE LEVEL"
"BALANCE"
Bass level
Adjustment Item
Display
Range
Fader
"FADER"
Bass Center Frequency "BASS FRQ"
40/50/60/70/80/100/
120/150 Hz
Exit Audio Control mode (Volume control mode)
|
8
English
Bass Q Factor
Bass Extend
"BASS Q FACTOR" 1.00/1.25/1.50/2.00
Volume offset
Loudness
Dual Zone System
"VOL-OFFSET" –8 — 0 (AUX: -8— +8)
"BASS EXT"
OFF/ON
"LOUD"
OFF/ON
OFF/ON
"2 ZONE"
Middle level
⁄
Adjustment Item
Middle Center Frequency "MIDDLE FRQ"
Middle Q Factor
Display
Range
0.5/1.0/1.5/2.0 kHz
•
•
* Function of KDC-X791/MP735U.
Volume offset: Sets each source’s volume as a difference
from the basic volume.
"MIDDLE Q FACTOR" 1.00/2.00
•
•
Loudness: Compensates for low and high tones
during low volume. (Only the low tone is
compensated for when the tuner is selected
as a source.)
Treble level
Adjustment Item
Treble Center Frequency "TREBLE FRQ"
Display
Range
10.0/12.5/15.0/17.5 kHz
Dual Zone System
5 Exit the Detail Audio Control mode
Main source and sub source (Auxiliary input) output
Front channel and Rear channel separately.
- Set up the channel of sub source by <Dual Zone
System Setting> (page 36).
- Select Main source by [SRC] button.
- Adjust the volume of Front channel by [VOL] knob.
- Adjust the volume of Rear channel by <Audio Control>
(page 8).
Press the [VOL] knob for at least 1 second.
⁄
•
When you set the Bass Extend to ON, low frequency
response is extended by 20%.
•
You can exit the Audio Control mode at anytime by
pressing any button except for [VOL] knob and [ATT]
button.
- The Audio Control has no effect on sub source.
You can use the Dual Zone System with the Auxiliary
input sources listed below.
•
- Internal auxiliary input. (KDC-X791/MP735U only)
- CA-C1AX/ CA-C2AX (optional accessory) connected to
this unit directly. (KDC-MP635 only)
Audio Setup
Setting the Sound system, such as Cross over
Network.
5 Exit Audio Setup mode
Press the [VOL] knob for at least 1 second.
1 Select the source to adjust
Press the [SRC] button.
Refer to <Selecting the Source> (page 7).
2 Enter Audio Setup mode
Press the [VOL] knob for at least 1 second.
3 Select the Audio Setup item to adjust
Press the [VOL] knob.
Each time you press the knob, the item to be
adjusted alternates between the items shown in
the table below.
4 Setup the Audio item
Turn the [VOL] knob.
Adjustment Item
Display
Range
Front High Pass Filter "HPF-F Fc" Through/40*/60*/80/100/120/
150/180/220* Hz
Rear High Pass Filter "HPF-R Fc" Through/40*/60*/80/100/120/
150/180/220* Hz
Low Pass Filter
"LPF-SW Fc" 50*/60/80/100*/120/
Through Hz
Subwoofer Phase
"SW PHASE" Reverse (180°)/ Normal (0°)
English
|
9
General features
When the call ends
Hang up the phone.
The "CALL" display disappears and the audio system
comes back ON.
Speaker Setting
Fine-tuning so that the System Q value is optimal
when setting the speaker type.
1 Enter Standby
⁄
Press the [SRC] button.
•
To use the TEL Mute feature, you need to hook up
the MUTE wire to your telephone using a commercial
telephone accessory. Refer to <Connecting Wires to
Terminals> (page 44).
Refer to <Selecting the Source> (page 7).
Select the "STANDBY" display.
2 Enter Speaker Setting mode
Press the [VOL] knob.
"SP SEL" is displayed.
3 Select the Speaker type
Function Control mode
To set up various functions of this unit, select tree-
structured function items.
Turn the [VOL] knob.
Each time you turn the knob, the setting alternates
between the settings shown in the table below.
1 Enter Function Control mode
Speaker type
OFF
Display
"OFF"
Press the [FNC] button.
For 5 & 4 in. speaker
For 6 & 6x9 in. speaker
For the OEM speaker
"5/4inch"
"6x9/6inch"
"O.E.M."
2 Select your desired setup item
Select a setup item using the Control knob.
Operation type
Operation
4 Exit Speaker Setting mode
Movement between items Turn the Control knob.
Press the [VOL] knob.
Selection of item
Press the Control knob.
Press the [FNC] button.
Return to previous item
Functions of items are as follows:
Subwoofer Output
Turning the Subwoofer output ON or OFF.
Display
"Menu"
Icon
Function of setup item
"MENU" Allows you to set up the environment. Refer
to <Menu system> (page 32).
Push the Control knob toward down for at least
2 seconds.
Each time you push the knob, Subwoofer output
switches ON and OFF.
When it is ON, "SUB WOOFER ON" is displayed.
"Display Select" "DISP" Allows you to set up the display. Refer to
page 11 to page 18.
"Preset Memory" "P.MEM" Allows you to put stations in the memory.
Refer to <Station Preset Memory> (page
22).
"File Scan" etc. "SCAN" Allows you to set how to play the CD and
etc.
audio file. Refer to <Play function of CD
and Audio file> (page 26).
TEL Mute
"Return"
Returns to the previous item.
"
"
The audio system automatically mutes when a call
comes in.
3 Select an option for the selected item
Refer to the related pages for the operation of
each option.
When a call comes in
"CALL" is displayed.
The audio system pauses.
4 Exit Function Control mode
Press the [FNC] button for at least 1 second.
Listening to the audio during a call
Press the [SRC] button.
The "CALL" display disappears and the audio system
comes back ON.
|
10
English
Display Type Selection
Changing the display mode.
⁄
•
To change the information by the Display Type, refer
to the page on the following table for the methods to
alternate by the Display Type.
1 Enter Display Type Selection mode
Using the Control knob, select "DISP" > "TYPE".
For the operation method, refer to <Function
Control mode> (page 10).
Display Type
Graphic 1
Status 2
Text 3
Upper 4
Middle 5
Lower 6
Text 7
A
B
C
D
E
F
12
11
12
11
12
—
—
—
—
—
—
—
—
13
13
13
—
—
—
13
13
13
—
—
—
—
—
—
12
—
—
—
—
—
—
—
15
—
—
—
—
—
—
2 Select the display Type
Turn the Control knob.
Select from the following display types:
Display Mode
"TYPE SELECT [A]"
Display
—
—
—
—
G-Analyzer 9
—
2
1
"TYPE SELECT [B]"
"TYPE SELECT [C]"
"TYPE SELECT [D]"
"TYPE SELECT [E]"
"TYPE SELECT [F]"
2
Display Type A/ Display Type B
1
Status Setting
Determine whether the On and Off statuses of
various functions are to be displayed on the Display
Type A/B.
3
2
0
4
5
6
0
0
1 Enter Status Setting mode
Using the Control knob, select "DISP" >
"STATUS".
For the operation method, refer to <Function
Control mode> (page 10).
2
4
5
6
!
2
7
2 Select the Status display
8
9
Turn the Control knob.
3 Exit Status Setting mode
Press the Control knob.
1 Graphic display part
2 Status display
3 Text display part
4 Upper text display part
5 Middle text display part
6 Lower text display part
7 Text display part
8 Graphic display part
9 G-Analyzer display part
0 Text icon display part
! Source icon display part
3 Exit Display Type Selection mode
Press the Control knob.
English
|
11
General features
Display Type A/ Display Type B
Text Display Selection
—Display Type B&E—
Graphic Display Selection
Changing the graphic Display.
Selecting the text display.
1 Enter Graphic Display Selection mode
Using the Control knob, select "DISP" >
"GRAPH".
For the operation method, refer to <Function
Control mode> (page 10).
1 Enter Text Dispaly Selection mode
Using the Control knob, select "DISP" > "TEXT".
For the operation method, refer to <Function
Control mode> (page 10).
2 Select the text
2 Select the graphic display
Turn the Control knob or push it towards left
or right.
Turn the Control knob or push it towards left
or right.
See <The text display> (page 14).
Display Type B: Information of condition column
"3" is displayed.
Display Type E: Information of condition column
"7" is displayed.
Select from the following displays:
Graphic display
Movie 1 – 2
Display
Wallpaper 1 – 6
Wallpaper scan
"SCAN"
3 Exit Text Dispaly Selection mode
Press the Control knob.
3 Exit Graphic Display Selection mode
⁄
Press the Control knob.
•
•
•
•
•
When LX-AMP is connected, the item setup by the
Display mode of LX-AMP is displayed. (KDC-X791)
When the music number exceeds 1000, only the last 3
digits of its number are displayed. (KDC-X791/MP735U)
Album name cannot be displayed in WMA file. (KDC-
MP635)
⁄
•
The setting of this function is available while "TYPE
SELECT [A]"/ "TYPE SELECT [B]" is selected for the Display
mode.
Music title, Artist name, and Album name cannot be
displayed in WAV file. (KDC-X791/MP735U)
When playing music from iPod or music edited by "Music
Editor", the folder name display may show something
different such as playlist or artist name depending on
the music selection procedure. (KDC-X791/MP735U)
In the Display Type B part, alternate information is
displayed when display without information is selected.
In the Display Type E part, no information is displayed
when display without information is selected.
•
•
|
12
English
Text Display Selection
— Display Type C&D—
Changing the text display.
1 Enter Text Display Selection mode
Using the Control knob, select "DISP" > "TEXT".
For the operation method, refer to <Function
Control mode> (page 10).
2 Select the text display part
Push the Control knob towards up or down.
The cursor (‰) moves to the selected text display
part.
Select the text
Turn the Control knob or push it towards left
or right.
See <The text display> (page 14).
Upper text display part: Information of condition
column "4" is displayed.
Middle text display part: Information of condition
column "5" is displayed.
Lower text display part: Information of condition
column "6" is displayed.
3 Exit Text Display Selection mode
Press the Control knob.
⁄
•
•
•
•
•
When LX-AMP is connected, the item setup by the
Display mode of LX-AMP is displayed. (KDC-X791)
When the music number exceeds 1000, only the last 3
digits of its number are displayed. (KDC-X791/MP735U)
Album name cannot be displayed in WMA file. (KDC-
MP635)
Music title, Artist name, and Album name cannot be
displayed in WAV file. (KDC-X791/MP735U)
When playing music from iPod or music edited by "Music
Editor", the folder name display may show something
different such as playlist or artist name depending on
the music selection procedure. (KDC-X791/MP735U)
Same information cannot be displayed in Upper text
display part, Middle text display part and Lower text
display part. However, the blank display is able to have
multiple selections.
•
•
•
In the upper text display part, alternate information is
displayed when display without information is selected.
In the middle text display part, the Kenwood logo is
displayed if the contents of the information cannot be
displayed. However, in the HD Radio source part, the
display becomes blank.
•
In the lower text display part, no information is displayed
when display without information is selected.
English
|
13
General features
In HD Radio source
The text display
Information
Station name
Title
Frequency
Clock
Date
Blank
Display
"Station Name"
"Title"
"Frequency"
"Clock"
"Date"
"Blank"
Condition
34
In Tuner source
34567
34
Information
Station name
Frequency
Clock
Date
Blank
Display
"SNPS"
"Frequency"
"Clock"
"Date"
"Blank"
Condition
34
34567
34567
567
34
34567
34567
567
In Satellite radio source
In CD & External disc source
Information
Channel Name
Music Title
Artist Name
Composer name
Category Name
Label Name
Comment
Display
Condition
34567
34567
34567
34567
34567
34567
34567
34
"Channel Name"
"Song Title"
"Artist Name"
"Composer Name"
"Category Name"
"Label Name"
"Comment"
"Channel Number"
"Clock"
Information
Disc title
Track title
Track number & Play time
Disc name
Clock
Display
Condition
34567
34567
34
"Disc Title"
"Track Title"
"P-Time"
"DNPS"
34567
34567
34567
567
"Clock"
Date
"Date"
Band & Channel Number
Clock
Date
Blank
"Blank"
34567
34567
567
"Date"
"Blank"
In Audio file source
Blank
Information
Music title & Artist name
Album name & Artist name
Folder name
File name
Play time & Music number
Clock
Display
Condition
34567
34567
34567
34567
34
"Title/Artist"
"Album/Artist"
"Folder Name"
"File Name"
"P-Time"
Display Type B/ Display Type C/ Display Type D
Font Color Selection
Selecting the display font color.
34567
34567
567
"Clock"
Date
"Date"
Blank
"Blank"
1 Enter Font Color Selection mode
Using the Control knob, select "DISP" >
"COLOR".
For the operation method, refer to <Function
Control mode> (page 10).
In Standby
Information
Standby
Clock
Display
"Source Name"
"Clock"
Condition
34
34567
34567
567
Date
"Date"
2 Select the text display part (Display Type C/
Display Type D only)
Blank
"Blank"
Push the Control knob towards up or down.
The cursor (‰) moves to the selected text display
part.
In Auxiliary input source
Information
Auxiliary input name
Clock
Display
"Source Name"
"Clock"
Condition
34
3 Select the Font Color
Turn the Control knob or push it towards left
or right.
34567
34567
567
Date
"Date"
Blank
"Blank"
4 Exit Font Color Selection mode
Press the Control knob.
⁄
•
When you selected the Display Type B display, select an
easy viewable font color.
|
14
English
•
•
G-Counter display
Display Type F
Adds the point of the acceleration level. The point is
determined after a lapse of 1 hr drive or at power off
(ACC Off), and then it will be displayed by the graph.
Furthermore, the G-Counter displays the average of the
past data by the line. (The scale of graph is determined
along with the largest point among the past 10 data.)
The value of G-Meter display and G-Counter display can
be reset by <G-Analyzer Reset> (page 17).
G-Analyzer display Selection
Changing the G-Analyzer display.
⁄
•
Before alternating G-Analyzer display, you are required to
setup <G-Counter Level seting> (page 17), <G-Analyzer
Calibration setup> (page 18), <G-Analyzer vehicle weight
setup> (page 18) and <G-Analyzer vehicle class setup>
(page 18).
3 Exit G-Analyzer display selection mode
Press the Control knob.
1 Enter G-Analyzer display selection mode
Using the Control knob, select "DISP" >
"GMENU".
For the operation method, refer to <Function
Control mode> (page 10).
2 Select the G-Analyzer display
Turn the Control knob.
Select from the following displays.
G-Force Sensor display
G- Graphic display
1 – 2
G-Meter display
(Graphic)
G-Meter display
(Text)
G-Counter display
⁄
•
•
•
G-Graphic display
Displays the condition of G in horizontal direction
(e.g; when turning the curve) by the graphic.
G-Meter display (Graphic)
Displays the maximum value of acceleration G, right
direction G, and left direction G by the numerical value.
G-Meter display (Text)
The maximum value of acceleration G, right direction G,
and left direction G is displayed by the numerical value.
The value of G is only the reference, so is different from
the actual value.
English
|
15
General features
Display Type F
Display Type F
G-Analyzer Stop Watch
G-Analyzer Horsepower Analysis
The control of stop watch can be started by G-
Analyzer function.
This measures the horsepower and displays graph
and max power. It automatically saves the highest
record.
¤
¤
•
Do not use G-Analyzer stop watch on the Public roads.
•
•
•
Do not use G-Analyzer Horsepower Analysis on the
Public roads.
Do not use this product in any way that prevents you
from driving safely.
Follow all driving laws and use common sense when
using this product.
1 Enter G-Analyzer Stop Watch mode
Using the Control knob, select "DISP" > "GMA"
> "STOP.W".
For the operation method, refer to <Function
Control mode> (page 10).
"STOP WATCH" is displayed.
⁄
•
2 Make the counter ready
Press the Control knob.
"Ready" is displayed.
Before alternating G-Analyzer Horsepower Analysis, you
are required to setup <G-Analyzer vehicle weight setup>
(page 18) and <G-Analyzer vehicle class setup> (page
18).
3 Start Count
1 Enter G-Analyzer Horsepower Analysis mode
Using the Control knob, select "DISP" > "GMA"
> "HP".
For the operation method, refer to <Function
Control mode> (page 10).
When G in the vertical direction is detected during
the travel, the count automatically starts.
"Running" is displayed.
⁄
•
You can also start the counter by pressing the Control
knob.
"HORSEPOWER" is displayed.
Previous max power and record are displayed.
4 Stop Count
2 Begin measurement
Press the Control knob.
"Ready" is displayed.
Press the Control knob.
"Stop" is displayed.
⁄
3 Start the car
•
The control will start again when you accelerate or press
the Control knob.
"Measure" is displayed.
After 15 seconds of measurement, the result is
displayed.
Do the operation after step2.
Display the result
When you Reset the Count
(While "Stop" is displayed)
Press the Control knob for at least 1 second.
The graph shows the variation in horsepower
between 0.1 to 15.0 seconds. The maximum power
is displayed in red and the markings provided at
intervals of 5 seconds are displayed in blue.
⁄
•
You can reset of count when the count is stopped.
¤
•
Pressing the Control knob also begins the measurement.
To prevent danger, push the control knob before starting
the car.
5 Exit G-Analyzer Stop Watch mode
Press the [FNC] button.
⁄
4 To display the maximum power in the section
Push the Control knob towards right or left.
Each time you push the Control knob, the
•
When Power off (ex; ACC OFF) while counting, the value
of 1 second or less will be "00".
maximum power in the section is displayed.
5 Exit G-Analyzer Horsepower Analysis mode
Press the [FNC] button.
|
16
English
Display Type F
⁄
G-Counter Level seting
•
Like your vehicle’s speedometer, G-Analyzer is no more
than a measuring function. The HP or G value measured
by this unit may not be completely accurate due to its
simplified method of measurement. The G-Analyzer is
only for reference and should not be used to confirm the
horsepower specifications of your vehicle.
Measuring after starting the car lowers the accuracy.
The record will not be renewed if the measurement is
discontinued.
The graph’s scale adjusts automatically to the
horsepower value.
The value of max power and record can be reset by <G-
Analyzer Reset> (page 17).
Calibrating G-Point. Setting the level according to
the kinds of vehicles.
1 Enter G-Counter Level setting mode
Using the Control knob, select "DISP" > "GMA"
> "LEVEL".
For the operation method, refer to <Function
Control mode> (page 10).
•
•
•
•
"G-COUNTER LEVEL" is displayed.
2 Select the G-Counter Level
Turn the Control knob.
Display
"Level1"
"Level2"
"Level3"
Setting
Counter is easy to go up.
Display Type F
Counter is hard to go up.
G-Analyzer Reset
Resets the value of G-Meter, G-Counter and G-
Analyzer Horsepower Analysis.
3 Exit G-Counter Level setting mode
Press the Control knob.
⁄
1 Enter G-Analyzer Reset mode
Using the Control knob, select "DISP" > "GMA"
> "RESET".
•
In the case of driving situations calling for few
accelerations, set the G-Point up to "Level1". In the case
of frequent accelerations, set it up to "Level3".
For the operation method, refer to <Function
Control mode> (page 10).
"G-RESET" is displayed.
2 Select the Reset item
Turn the Control knob.
Display
Setting
"Meter Reset"
Reset the value of G-Meter.
"Power Reset"
Reset the value of G-Analyzer Horsepower
Analysis.
"Counter Reset"
Reset the value of G-Counter.
3 Determine the item you want to reset
Press the Control knob.
4 Reset the value
Select "YES" using the Control knob.
"Reset OK" is displayed.
5 Exit G-Analyzer Reset mode
Press the [FNC] button.
English
|
17
General features
Display Type F
2 Select the weight numbers
In Standby mode
Turn the Control knob.
G-Analyzer Calibration setup
G-Analyzer requires calibration for horizontal
acceleration and braking.
⁄
•
The weight input range is between 1000-9999 lbs.
3 Select the digits to enter
Push the Control knob towards right or left.
⁄
•
To ensure accurate calibration, go through the following
steps at a level place where you can move the vehicle
straight ahead.
4 Repeat steps 2 and 3, and complete the weight
input.
5 Exit G-Analyzer vehicle wight setup mode
1 Park the vehicle in a horizontal location
Press the Control knob.
2 Enter G-Analyzer Calibration setup mode
Using the Control knob, select "DISP" > "GMA"
> "CAL".
For the operation method, refer to <Function
Control mode> (page 10).
Display Type F
In Standby mode
"G-CALIBRATION" is displayed.
G-Analyzer vehicle class setup
3 Start Calibration of horizontal direction
Press the Control knob.
Once "Move Forward" appears on the display, the
Enter vehicle class to calculate horsepower.
1 Enter G-Analyzer vehicle class setup mode
Using the Control knob, select "DISP" > "GMA" >
"HP SET" > "CLASS".
For the operation method, refer to <Function
Control mode> (page 10).
vehicle must be advanced.
4 Start Calibration of straight direction
Start moving the vehicle ahead.
Calibration of straight direction automatically starts.
When the Calibration is finished, "Calibration OK" is
displayed.
"CLASS SELECT" is displayed.
2 Select vehicle class
Turn the Control knob.
⁄
Each time you push the knob, the vehicle class
alternates between the modes shown in the table
below.
•
If you fail to complete the calibration, "No Calibration" is
displayed. In such a case, repeat steps 1 through 4.
5 Exit G-Analyzer Calibration setup mode
Display
Press the [FNC] button.
"Mid Size"
"Full Size"
"SUV"
"Van/ Mini-Van"
"Pickup Truck"
"Sporty"
Display Type F
In Standby mode
G-Analyzer vehicle weight setup
"Compact"
Enter vehicle weight to calculate horsepower.
3 Exit G-Analyzer vehicle class setup mode
1 Enter G-Analyzer vehicle weight setup mode
Using the Control knob, select "DISP" > "GMA" >
"HP SET" > "WEIGHT".
Press the Control knob.
For the operation method, refer to <Function
Control mode> (page 10).
"WEIGHT INPUT" is displayed.
|
18
English
Station/Disc Naming (SNPS/DNPS)
Attaching a title to a Station or CD.
9 Exit Menu mode
Press the [FNC] button.
⁄
1 Receive/play the station/disc you want to
attach a title to
•
When operation stops for 10 seconds the name at that
time is registered, and Name Set mode closes.
Memory numbers
•
⁄
- FM/AM: 30 stations
- Internal CD player: 10 discs
•
A title cannot be attached to MD or Audio file media.
- External CD changer/ player: Varies according to the
CD changer/ player. Refer to the CD changer/ player
manual.
Change the title of station/CD by the same operation
used to name it.
2 Enter Menu mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 10).
•
3 Select Name set mode
Turn the Control knob.
Select the "Name Set" display.
4 Enter Name set mode
Press the Control knob for at least 1 second.
5 Move the cursor to the enter character
position
Push the Control knob towards right or left.
6 Select the character type
Press the Control knob.
Each time you press the knob, the character type
alternates between the types shown in the table
below.
Character type
Alphabet upper case
Alphabet lower case
Numbers and symbols
Special characters (Accent characters)
7 Select the characters
Turn the Control knob or push it towards up or
down.
⁄
•
Enter characters by using a remote control with numbers
buttons.
Example: If you are entering "DANCE".
Character
"D"
"A"
"N"
"C"
Button
[3]
[2]
[6]
[2]
Times pressed
1
1
2
3
2
"E"
[3]
8 Repeat steps 5 through 7 and enter the name.
English
|
19
General features
Theft Deterrent Faceplate
The faceplate of the unit can be detached and taken
with you, helping to deter theft.
Removing the Faceplate
1 Press the Release button.
Drop open the faceplate.
2 Drawing the faceplate to left side pull it to
forward and remove it.
¤
•
The faceplate is a precision piece of equipment and can
be damaged by shocks or jolts.
•
•
Keep the faceplate in its faceplate case while detached.
Do not expose the faceplate (and the faceplate case) to
direct sunlight or excessive heat or humidity. Also avoid
places with too much dust or the possibility of water
splashing.
Reattaching the Faceplate
1 Align the shaft on the unit with the depression
on the faceplate.
2 Push the faceplate in until it clicks.
The faceplate is locked in place, allowing you to use
the unit.
|
20
English
Tuner features
AUTO/AME
FM
AM
ꢀ
E
1 - 6
Control knob
SRC
FNC
ST indicator
Frequency display
Band display Preset station number
Function icon
Tuning
Tuning Mode
Selecting the station.
Choose the tuning mode.
Press the [AUTO] button.
1 Select tuner source
Press the [SRC] button.
Select the "TUNER" display.
Each time you press the button, the Tuning mode
alternates between the modes shown in the table
below.
Refer to <Selecting the Source> (page 7).
Tuning mode
Display
Operation
2 Select the band
Auto seek
"Seek Mode: Automatic search for a station.
Auto1"
Push the Control knob towards [FM] or [AM].
Each time you push the knob toward [FM], it
switches between the FM1, FM2, and FM3 bands.
Preset station seek "Seek Mode: Search in order of the stations in
Auto2" the Preset memory.
Manual
"Seek Mode: Normal manual tuning control.
Manual"
3 Tune up or down band
Push the Control knob towards [4] or [¢].
⁄
•
During reception of stereo stations the "ST" indicator is
ON.
English
|
21
Tuner features
Function of remote control
⁄
•
Direct Access Tuning
This function can be operated with [1] — [6] button.
- Press the desired [1] — [6] button for at least 2 seconds.
Entering the frequency and tuning.
1 Select the band
Press the [FM] or [AM] button.
2 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
Auto Memory Entry
Putting stations with good reception in the memory
automatically.
"– – – –" is displayed.
1 Select the band for Auto Memory Entry
3 Enter the frequency
Push the Control knob towards [FM] or [AM].
Press the number buttons on the remote
control.
Example:
Desired frequency
92.1 MHz (FM)
810 kHz (AM)
2 Open Auto Memory Entry
Press the [AME] button for at least 2 seconds.
When 6 stations that can be received are put in the
memory Auto Memory Entry closes.
Press button
[0], [9], [2], [1]
[0], [8], [1], [0]
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
Preset Tuning
Recalling the stations in the memory.
1 Select the band
Push the Control knob towards [FM] or [AM].
Station Preset Memory
Putting a station in the memory.
2 Enter Preset Tuning Select mode
Turn the Control knob.
1 Select the band
3 Select a desired station in the memory
Push the Control knob towards [FM] or [AM].
Turn the Control knob.
2 Select the frequency to put in the memory
4 Recall the station
Push the Control knob towards [4] or [¢].
Press the Control knob.
3 Enter Preset Memory mode
Cancelling Preset Tuning
Press the [FNC] button.
Using the Control knob, select "P.MEM".
For the operation method, refer to <Function
Control mode> (page 10).
⁄
•
This function can be operated with [1] — [6] button.
- Press the desired [1] — [6] button.
4 Select the number to put in the memory
Turn the Control knob.
5 Determine the number to put in the memory
Press the Control knob.
6 Allow the determined number to take effect
Press the Control knob.
Cancelling the Preset Memory mode
Press the [FNC] button.
|
22
English
CD/USB device/Audio file/External disc control features
ꢀ
E
FNC
S.MODE
SCAN RDM/ REP
A.RDM
M.RDM SRC
Control knob
Release button
IN indicator
Folder number
File number
Function icon
Play time
When a disc is inserted
Press the [SRC] button.
Playing CD & Audio file
Select the "Compact Disc" display.
When there is no disc inserted
Refer to <Selecting the Source> (page 7).
1 Drop open the faceplate
Pause and play
Press the Release button.
Press the Control knob.
Each time you press the knob, the audio pauses or
plays.
2 Insert a disc.
3 Push the faceplate on the left side, and return it
to its former position.
Eject the disc
¤
1 Drop open the faceplate
•
When the faceplate has been dropped open, it might
interfere with the shift lever or other vehicle function.
If this happens, pay attention to safety and move the
shift lever or take an appropriate action to remove the
obstacle, then operate the unit.
Press the Release button.
2 Eject the disc
Press the [0] button.
•
Do not use the unit with the faceplate in the open
condition. If it’s used in the open position dust can enter
the inside part and cause damage.
⁄
•
For the audio files and discs you can play with this unit,
refer to <About Audio file> (page 5).
•
When a disc is inserted, the "IN" indicator is ON.
Next page 3
English
|
23
CD/USB device/Audio file/External disc control features
Pause and play
Press the [38] button.
3 Press the faceplate on the left side, and return it
to its former position.
Each time you press the knob, the audio pauses or
plays.
⁄
•
You can eject the disc for 10 minutes after switching off
the engine.
Removing the USB device
1 Drop open the faceplate
Press the Release button.
2 Set the remove mode as the USB source
Press the [0] button for at least 2 seconds.
The 0 indicator blinks.
Function of KDC-X791/KDC-MP735U
Playing USB (iPod) device
When the USB device is not connected
3 Remove the USB device.
Connect the USB device
Playback of the file contained in the USB device
starts.
Function of KDC-X791/KDC-MP735U
When the USB device is connected
Drive Search
Selecting the device inserted in the Multi Card
Reader.
Select USB source
Press the [SRC] button.
Select the "USB" (or "iPod") display.
Refer to <Selecting the Source> (page 7).
1 Put the playback to pause
⁄
Press the [S.MODE] button.
•
•
•
For the audio files that can be played with this unit and
the devices that can be connected to this unit, refer to
<About Audio file> (page 5).
2 Select a device
Push the Control knob towards up or down.
The word "iPod" appearing in this manual indicates the
iPod connected with the KCA-iP200 (optional accessory).
Refer to <About Audio file> (page 5).
If you start playback after connecting the iPod, the music
that has been played by the iPod is played first.
In this case, "RESUMING" is displayed without displaying
a folder name, etc. Changing the browse item will
display a correct title, etc.
3 Restart playback
Press the Control knob.
⁄
•
This unit is compliant with Multi Card Readers with a
maximum of 4 slots.
•
If a device is inserted during connection of the Multi
Card Reader, it is not recognized. Select the Remove
mode with reference to <Playing USB (iPod) device>
(page 24), remove the Card Reader, and then insert the
memory.
•
When the iPod is connected to this unit, "KENWOOD" or
"✓" is displayed on the iPod to indicate that you cannot
operate the iPod.
•
•
•
When the USB device is connected to this unit, it can be
charged up provided that this unit is powered.
When the Multi Card Reader is used, refer to <Drive
Search> (page 24).
After you stopped playing a file contained in the USB
device, you can restart playing the file from the point
where you stopped its playback.
Even after removing the USB device, you can restart
playing the file from the point where you stopped its
playback as long as the files contained in the USB device
are all the same.
•
Be sure to insert the USB device connector as far as it will
go.
|
24
English
Function of disc changer/ Audio file
Playing External Disc
Playing discs set in the optional accessory disc
player connected to this unit.
Disc Search/Folder/Album Search
Switching between folders/albums contained in
the disc in the disc changer, media, or device being
played now.
Press the [SRC] button.
Refer to <Selecting the Source> (page 7).
Select the display for the disc player you want.
Display examples:
Push the Control knob towards up or down.
⁄
Display
"CD Changer"
"MD Changer"
Disc player
CD changer
MD changer
•
This function is not available on iPod and the music
edited by "Music Editor".
Pause and play
Press the Control knob.
Each time you press the knob, the audio pauses or
plays.
Function of remote control
Direct Music Search
Doing Music Search by entering the music number.
⁄
•
The functions that can be used and the information that
can be displayed will differ depending on the external
disc players being connected.
1 Enter the music number
Press the number buttons on the remote
control.
⁄
•
You can select Direct music Search up to 999.
2 Do music Search
Fast Forwarding and Reversing
Press the [4] or [¢] button.
Fast Forwarding
Hold down toward [¢] with the Control knob.
Release to resume the playback.
Cancelling Direct Music Search
Press the [38] button.
⁄
Reversing
•
This function is not available on iPod and the music
edited by "Music Editor".
Hold down toward [4] with the Control knob.
Release to resume the playback.
⁄
•
•
There is no sound while the Audio file is being searched.
You cannot fast Forwarding and Reversing while AAC file
is being played. (KDC-MP635)
Function of disc changers with remote control
Direct Disc Search
Doing Disc Search by entering the disc number.
1 Enter the disc number
Press the number buttons on the remote
control.
Music Search
Switching between music contained in the disc or
folder being played now.
2 Do Disc Search
Press the [FM+] or [AM–] button.
Push the Control knob towards [4] or [¢].
Cancelling Direct Disc Search
Press the [38] button.
English
|
25
CD/USB device/Audio file/External disc control features
Function of Audio file
Play function of CD and Audio file
Setting up the Repeat Play and Scan Play
File Select
Selecting the music you want to listen to from the
device or media being played now.
1 Set up the play function
Using the Control knob, set your desired setup
item to On/Off.
1 Enter File Select mode
For the operation method, refer to <Function
Turn the Control knob.
Control mode>.
When the play function is turned on, “ON” is
displayed.
2 Search for music
Select the category item using the Control
knob.
Display/Icon
"File Scan"/
"SCAN"
Press button* Function
[SCAN] Plays the beginnings of the audio
Operation system for iPod
files in the current folder or genre
one after another for 10 seconds
each.
Plays the audio files in the current
folder or genre at random.
Plays the audio files in the current
disc or USB device at random.
Plays the current audio file
repeatedly.
Operation type
Operation
Movement between Turn the Control knob.
items
"Folder RDM"/ [RDM]
"RDM"
Selection of item
Press the Control knob.
Return to previous item Push the Control knob towards up.
"All Random"/ [A.RDM]*2
Return to first item
Push the Control knob towards up for at least
1 second.
"A.RDM"*1
"File Repeat"/
"FiREP"
[REP]
Operation system for other than iPod
Operation type Operation
"Folder Repeat"/ [REP]*3
"FoREP"
Plays the audio files in the current
folder or genre repeatedly.
Movement between items Turn the Control knob.
"(Track) Scan"/ [SCAN]
"SCAN"
Plays the beginnings of the music
on the current CD/MD one after
another for 10 seconds each.
Plays the music on the current
CD/MD at random.
Plays the music in the disc changer
at random.
Plays the current music on the
current CD/MD repeatedly.
Selection of item*1
Selection of item*2
Push the Control knob towards right.
Press the Control knob.
Push the Control knob towards right.
"Disc Random"/ [RDM]
"RDM"
"Magazine RDM"/ [M.RDM]
"M.RDM"
"(Track) Repeat"/ [REP]
"T.REP"
"Disc Repeat"/ [REP]*3
"D.REP"
Return to previous item Push the Control knob towards left.
Return to first item
Push the Control knob towards left for at least
1 second.
•
•
*1 Function of KDC-X791/MP735U.
*2 Function of KDC-MP635.
Plays the music on the current
CD/MD repeatedly.
The "2" or "3" symbol shown beside the displayed
item indicates that the item is preceded or followed
by another item.
⁄
Selecting a music will play it from the beginning.
•
* The functions listed in the table above can be
operated with buttons on the unit.
Cancelling File Select
Press the [FNC] button.
•
•
•
*1 Function of KDC-X791/MP735U.
*2 Press the [A.RDM] button for at least 1 second.
*3 Press the [REP] button twice.
⁄
•
Even when the iPod is connected, you can change the
operation method from <Operation method for iPod> to
<Operation method for other than iPod>. Refer to <iPod
Mode Setting> (page 34).
2 Select an option for the selected item
Press the Control knob.
Pressing the Control knob switches between
options.
3 Exit Play Function Set mode
Press the [FNC] button.
⁄
•
Only the icons available to the current source are
displayed.
|
26
English
Text/Title Scroll
Scrolling the displayed CD text, Audio file text, or
MD title.
Push the Control knob toward up for at least 2
seconds.
⁄
•
When the <Display Illumination Control> (page 35) is set
to OFF, the display may black out while scrolling.
English
|
27
Satellite Radio tuner control features
AUTO
FM
AM
ꢀ
E
1 - 6
FNC
SRC Control knob
Band display
Channel number
Function icon
Select Satellite Radio Mode
Switching Seek Mode
Selecting the Satellite Radio Tuner (optional
accessory) connected to this unit.
Sets the seeking mode.
Press the [AUTO] button.
Each time you press the button, the Seek mode
alternates between the operations shown in the
table below.
Selecting Satellite Radio Mode
Press the [SRC] button.
Select the "SAT" display.
Refer to <Selecting the Source> (page 7).
Display
Operation
"Seek : Channel"
"Seek : Preset"
Normal manual seeking control.
Search in order of the channels in the Preset
memory.
⁄
•
You need to register to the service provider to receive
the service by Satellite Radio. Consult the service
provider if "CALL TO SUBSCRIBE" appears.
•
•
The radio may take a little time to start receiving after
you select the Satellite Radio source.
If the signal reception fails, "Acquiring Signal" appears.
Select the channel
Selecting the channel.
Push the Control knob towards [4] or [¢].
|
28
English
Category and Channel Search
Selecting the Preset Band
Selecting the channel and category you want to
receive.
Push the Control knob toward [FM].
Each time you push the knob, the preset band
alternates between the SR1, SR2, SR3 and SR4.
1 Enter Category and Channel Search mode
Press the Control knob.
2 Select the Category
Push the Control knob towards up or down.
Channel Preset Memory
Putting the channel in the memory.
⁄
•
It is the item when the category of Middle text display
part is selected.
1 Select the preset band
3 Select the Channel
Push the Control knob toward [FM].
Push the Control knob towards [4] or [¢].
2 Select the channel to put in the memory
⁄
Push the Control knob towards [4] or [¢].
•
You cannot Channel search until the category
information is acquired.
3 Enter Preset Memory mode
Using the Control knob, select "P.MEM".
For the operation method, refer to <Function
Control mode> (page 10).
Cancelling Category and Channel Search mode
Press the Control knob.
4 Select the number to put in the memory
Turn the Control knob.
5 Determine the number to put in the memory
Function of remote control
Press the Control knob.
Direct Access Tuning
Entering the channel and tuning.
6 Allow the determined number to take effect
Press the Control knob.
1 Enter Direct Access Tuning mode
Press the [DIRECT] button on the remote
control.
Cancelling the Preset Memory mode
Press the [FNC] button.
⁄
2 Enter the channel
•
Only the channel number is stored. Category information
is not stored.
Press the number buttons.
•
This function can be operated with [1] — [6] button.
- Press the desired [1] — [6] button for at least 2 seconds.
3 Do Channel Search
Push the Control knob towards [4] or [¢].
Cancelling Direct Access Tuning
Press the [DIRECT] button on the remote
control.
⁄
•
If you make no button operation for 10 seconds, the
Direct Access Tuning mode is automatically canceled.
If you cannot receive any signal in the input Channel due
to bad conditions on radio wave or other such problems,
"Acquiring Signal" appears.
•
English
|
29
Satellite Radio tuner control features
Preset Tuning
Recalling the channels in the memory.
1 Select the preset band
Push the Control knob toward [FM].
2 Enter Preset Tuning Select mode
Turn the Control knob.
3 Select a desired station in the memory
Turn the Control knob.
4 Recall the station
Press the Control knob.
Cancelling Preset Tuning
Press the [FNC] button.
⁄
•
This function can be operated with [1] — [6] button.
- Press the desired [1] — [6] button.
Channel Scan
Checks every receivable Channel for 10 seconds.
1 Start Channel Scan
Press the [AUTO] button for at least 2 seconds.
The channel number display blinks.
2 Release the button when the music you want
to hear is received
Press the [AUTO] button for at least 2 seconds.
Text Scroll for Satellite Radio source
Scrolls the displayed channel name and other items.
Push the Control knob toward up for at least 2
seconds.
⁄
•
When the <Display Illumination Control> (page 35) is set
to OFF, the display may black out while scrolling.
|
30
English
HD Radio control features
AUTO/AME
FM
AM
ꢀ
E
1 - 6
FNC
SRC Control knob
ST indicator
Band display Preset station number
Function icon
Frequency display
About HD Radio
Tuning
Selecting the station.
•
When you connect an HD Radio, Tuner features
of the unit are disabled and changed to HD Radio
tuner features. A portion of the setting methods
including the Tuning Mode will change.
1 Select HD Radio source
Press the [SRC] button.
Select the "HD Radio" display.
Refer to <Selecting the Source> (page 7).
•
With the HD Radio tuner, you can use the similar
functions to <Station Preset Memory>, <Auto
Memory Entry>, and <Preset Tuning> of Tuner
features. Refer to Tuner features for how to use
the functions.
2 Select the HD FM band
Push the Control knob toward [FM].
Each time you push the knob to [FM], the band
alternates between the HF1, HF2, and HF3 bands.
Select the HD AM band
Push the Control knob toward [AM].
3 Tune up or down band
Push the Control knob towards [4] or [¢].
English
|
31
Menu system
FNC
SRC Control knob
Function icon
You can continue by returning to step 2 and
setting other items.
Menu System
Setting beep sound during operation, etc.
functions.
The Menu system basic operation method is
explained here. The reference for the Menu items
and their setting content is after this operation
explanation.
4 Exit Menu mode
Press the [FNC] button.
⁄
•
When other items those applicable to the basic
operation method above are displayed, their setting
content chart is entered. (Normally the setting listed at
the top of the chart is the original setting.)
Also, the explanation for items that are not applicable
(<Manual Clock Adjustment> etc.) are entered step by
step.
1 Enter Menu mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 10).
•
Three menu items appear on the display. The menu item
displayed at the center is the one you can adjust.
2 Select the menu item
Turn the Control knob or push it towards up or
down.
Example: When you want to set the beep sound
select the "Beep" display.
3 Set the menu item
Push the Control knob towards right or left.
Example: When you select "Beep", each time you
push the knob it alternates between
"Beep : ON" or "Beep : OFF". Select 1 of
them as the setting.
|
32
English
In Standby mode
9 Exit Security Code mode
Press the [FNC] button.
Activating Security Code
Resetting the Security Code function when the
audio unit is first used after removed from the
battery power source or the Reset button is
pressed
Activating the Security Code disables the usage
of audio unit by someone else. Once the Security
Code is activated, the entry of authorized Security
Code is required to turn on the audio unit when it is
removed from the vehicle. Indication of this Security
Code activation prevents your precious audio unit
from stealing.
1 Turn the power ON.
2 Do the step 4 through 7 operation, and enter
the Security Code.
"Approved" is displayed.
Now, you can use the unit.
⁄
•
You can set the Security Code with a 4 digit number of your
choice.
⁄
•
The Security Code cannot be displayed or referenced. Make
a note of the Security Code and treasure it up.
•
When the Security Code function is activated, "Security
Set" changes to "Security Clear".
•
To deactivate the Security Code function, see the next
section <Deactivating Security Code>.
1 Enter Standby
Press the [SRC] button.
Select the "STANDBY" display.
Refer to <Selecting the Source> (page 7).
2 Enter Menu mode
In Standby mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 10).
Deactivating Security Code
To deactivate the Security Code function.
"Security Set" is displayed.
1 Select Security Code mode
Turn the Control knob.
Select the "Security Clear" display.
3 Enter Security Code mode
Press the Control knob for at least 1 second.
When "Enter" is displayed, "SECURITY SET" is also
displayed.
2 Enter Security Code mode
Press the Control knob for at least 1 second.
When "Enter" is displayed, "SECURITY CLEAR" is also
displayed.
4 Select the digits to enter
Push the Control knob towards right or left.
5 Select the Security Code numbers
Turn the Control knob or push it towards up or
down.
3 Select the digits to enter
Push the Control knob towards right or left.
4 Select the Security Code numbers
Turn the Control knob or push it towards up or
down.
6 Repeat step 4 and 5, and complete the Security
Code.
7 Confirm the Security Code
5 Repeat steps 3 and 4, and complete the
Press the Control knob for at least 3 seconds.
When "Re-Enter" is displayed, "SECURITY SET" is also
displayed.
Security Code.
6 Press the Control knob for at least 3 seconds.
"Clear" is displayed.
The Security Code function deactivates.
8 Do the step 4 through 7 operation, and reenter
the Security Code.
"Approved" is displayed.
7 Exit Security Code mode
Press the [FNC] button.
The Security Code function activates.
⁄
⁄
•
If a wrong security code is entered, "Error" is displayed.
Enter a correct security code.
•
If you enter the wrong code in step 4 through 6, repeat
from step 4.
English
|
33
Menu system
In Standby mode
In Standby mode
Source Select Mode
Manual Clock Adjustment
Setting up the Source Select mode.
1 Select Clock Adjustment mode
Turn the Control knob.
Select the "Clock Adjust" display.
Display
Setting
"SRC Select : 1"
Displays source icons for your choice.
"SRC Select : 2"
Allows you to select sources one after another.
2 Enter Clock Adjust mode
Press the Control knob for at least 1 second.
The clock display blinks.
3 Selecting the item (hours or minutes) to adjust
Push the Control knob towards right or left.
The items that are blinking are items that you can
adjust.
Function of KDC-X791/KDC-MP735U
In USB mode with iPod connected
iPod Mode Setting
4 Adjust each item
Setting up the iPod operation method in File Select.
Turn the Control knob or push it towards up or
down.
Display
"iPod Mode : ON"
Setting
Uses the operation method similar to that of
iPod.
Uses the operation method different from that
of iPod.
5 Exit Clock adjustment mode
Press the [FNC] button.
"iPod Mode : OFF"
In Standby mode
In Standby mode
Date Adjustment
Touch Sensor Tone
Setting the operation check sound (beep sound)
ON/OFF.
1 Select Date Adjust mode
Turn the Control knob.
Select the "Date Adjust" display.
Display
"Beep : ON"
"Beep : OFF"
Setting
Beep is heard.
Beep canceled.
2 Enter Date Adjust mode
Press the Control knob for at least 1 second.
The date display blinks.
3 Selecting the item (day, month, or year) to
adjust
Push the Control knob towards right or left.
The items that are blinking are items that you can
adjust.
4 Adjust each item
Turn the Control knob or push it towards up or
down.
5 Repeat step 3 and 4 operation and adjust the
date.
6 Exit Date adjustment mode
Press the [FNC] button.
|
34
English
In Standby mode
Display Illumination Control
This function turns off the display when you
perform no operation for 5 seconds. This function is
effective when you are driving at night.
Date Mode
Setting the date format.
1 Select Date Mode
Display
Setting
Turn the Control knob.
Select the "Date Mode" display.
"Display : ON"
Keeps the display on.
Turns off the display when you perform no
operation for 5 seconds.
"Display : OFF"
2 Enter Date mode
Press the Control knob for at least 1 second.
3 Select the date format
Turn the Control knob or push it towards up or
down.
⁄
•
•
•
Set the Display Illumination Control when the
<Demonstration mode Setting> (page 40) is set to OFF.
When the display is off, pressing any key will turn on the
display.
When the display is off, you cannot perform any
operation except for the following:
4 Exit Date mode
Press the [FNC] button.
•
•
•
•
Volume
Attenuator
Selecting the source
Turning off the power
In Standby mode
DSI (Disabled System Indicator)
A red indicator will blink on the unit after the
faceplate is removed, warning potential thieves.
•
During function control, such as the Menu System, the
display stays on.
Display
Setting
"DSI : ON"
"DSI : OFF"
LED flashes.
LED OFF.
In Standby mode
Dimmer
Dimming this unit’s display automatically when the
vehicle light switch is turned ON.
Display
Setting
"Dimmer : ON"
"Dimmer : OFF"
The display dims.
The display doesn’t dim.
In Standby mode
Built-in Amp Setting
Controlling the built-in amplifier.
Turning OFF this control enhances the preout
quality.
Display
Setting
"AMP : ON"
"AMP : OFF"
The built-in amplifier activates.
The built-in amplifier deactivates.
English
|
35
Menu system
Other than Standby mode/
When the Dual Zone System is ON
Function of KDC-X791
Other than Standby mode
Dual Zone System Setting
B.M.S. (Bass Management System)
Setting the Front channel and Rear channel sound
in the Dual Zone System.
Adjust the bass boost level of the external amplifier
using the main unit.
Display
Setting
Display
Setting
"AMP Bass : Flat"
"AMP Bass : +6"
"AMP Bass : +12"
"AMP Bass : +18"
Bass boost level is flat.
"Zone 2 : Rear" Sub source (Auxiliary input source) is to be rear
channel.
"Zone 2 : Front" Sub source (Auxiliary input source) is to be front
channel.
Bass boost level is low (+6dB).
Bass boost level is mid (+12dB).
Bass boost level is high (+18dB).
⁄
•
Refer to the catalog or instruction manual for power
amplifiers that can be controlled from this unit.
For amplifiers, there are the models you can set from Flat
to +18 dB, and the models you can set from Flat to +12
dB.
When an amplifier that can only be set to +12 is
connected to the unit, "AMP Bass : +18" will not work
correctly even if it is selected.
In Audio file source
•
Supreme Setting
When AAC, MP3 or WMA files encoded at a low bit
rate (less than 96kbps (fs= 44.1k, 48kHz)) are played,
this function restores their high frequency region
to approach the sound quality of equivalents of
these files encoded at a high bit rate. Processing is
optimized for the compression format used (AAC,
MP3, or WMA), and adjustment is made for the bit
rate used.
Function of KDC-X791
Other than Standby mode
B.M.S. Frequency Offset
Display
Setting
"Supreme : ON"
Plays sound using the Supreme function.
Setting the central frequency, boosted by B.M.S.
"Supreme : OFF" Plays the original sound stored in the audio file.
Display
Setting
"AMP FREQ : Normal"
"AMP FREQ : Low"
Boost with the normal central frequency.
Drop the normal central frequency 20%.
⁄
•
•
The sound effect may be imperceptible depending
on the relationship between the audio file format and
setting.
This function is not available on iPod.
|
36
English
Function of KDC-X791
In HD Radio mode
When LX AMP unit connecting
Receive mode Setting
Sets the receive mode.
AMP Control
You can control the LX AMP connected to the unit.
1 Select the Receive mode
Turn the Control knob.
Select the "Receive Mode" display.
1 Select AMP Control mode
Turn the Control knob.
Select the "AMS Control" display.
2 Enter Receive mode
2 Enter AMP Control mode
Press the Control knob for at least 1 second.
Press the Control knob for at least 1 second.
3 Set the Receive mode
3 Select the AMP Control item for adjustment
Push the Control knob towards up or down.
Each time you push the knob, the Receive mode
alternates between the modes shown in the table
below.
Push the Control knob towards up or down.
⁄
•
For the details on the AMP Control item, see the
Instruction manual attached to the LX AMP.
Receive mode Display
Operation
Auto mode
"Auto"
Analog broadcasts and digital
broadcasts will be switched
automatically.
4 Adjust the AMP Control item
Push the Control knob towards right or left.
5 Exit AMP Control mode
When both are being transmitted,
the digital broadcast will have
priority.
Press the [FNC] button.
⁄
Digital
Analog
"Digital"
"Analog"
Digital broadcasts only.
Analog broadcasts only.
•
You cannot use the LX AMP operation during standby
mode.
4 Exit Receive mode
Press the [FNC] button.
⁄
In FM reception
•
Even if the Receive mode is set to "Auto", when the Ball
game mode program (non-delayed broadcast program)
is received, the Receive mode will automatically switch
to Analog broadcast only.
CRSC (Clean Reception System Circuit)
Temporarily have reception alternate from stereo to
mono to reduce multi-path noise when listening to
the FM station.
Display
Setting
"CRSC : ON"
"CRSC : OFF"
The CRSC is ON.
The CRSC is OFF.
In Satellite radio source
Electronic Serial Number (ESN)
display
⁄
•
Strong electrical fields (such as from power lines) may
Displaying the Electronic Serial Number.
cause unstable sound quality when CRSC is turned ON.
In such a situation, turn it OFF.
Display
"ESN=************"
⁄
•
Electronic Serial Number (ESN)
It is important to retain the unit serial number and the
electronic Satellite radio Identification number for service
activation and potential service changes.
English
|
37
Menu system
Auxiliary Input Display Setting &
Station/Disc Naming
Text Scroll
Setting the displayed text scroll.
Selecting the display when changing to Auxiliary
input source. For the Station/Disc Naming refer to
the <Station/Disc Naming (SNPS/DNPS)> (page 19).
Display
"Scroll : Auto"
"Scroll : Manual"
Setting
Repeats scroll.
Scrolls when the display changes.
1 Select Auxiliary input source
Press the [SRC] button.
Select the "AUX"/"AUX EXT" display.
⁄
•
The text scrolled is listed below.
- CD text
Refer to <Selecting the Source> (page 7).
- Folder name/ File name/ Music title/ Artist name/
Album name
- MD title
- Radio text
- Text for the Satellite radio source, HD Radio source,
including Channel name, etc.
2 Enter Menu mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 10).
"MENU" is displayed.
3 Select Auxiliary input display setting mode
Turn the Control knob.
Select the "Name Set" display.
Function of KDC-X791/KDC-MP735U
In Standby mode
4 Enter Auxiliary input display setting mode
Press the Control knob for at least 1 second.
The presently selected Auxiliary input display is
displayed.
Built-in Auxiliary input Setting
Set the Built-in Auxiliary Input function.
Display
Setting
5 Select the Auxiliary input display
"Built in AUX : OFF" When selecting the source there’s no Auxiliary Input.
"Built in AUX : ON" When selecting the source there’s Auxiliary Input.
Turn the Control knob or push it towards up or
down.
Each time you push the knob, the display alternates
as listed below.
• "AUX"/"AUX EXT"
• "DVD"
• "PORTABLE"
• "GAME"
In Standby mode
CD Read Setting
When there is a problem with playing a CD with
special format, this setting plays the CD by force.
• "VIDEO"
• "TV"
6 Exit Auxiliary input display setting mode
Display
"CD Read : 1"
"CD Read : 2"
Setting
Play CD and Audio file.
Play CD by force.
Press the [FNC] button.
⁄
•
When operation stops for 10 seconds, the name at that
time is registered, and the Auxiliary input display setting
mode closes.
⁄
•
Some music CDs may not play even in the "CD Read : 2"
mode.
•
The Auxiliary input display can be set only when the
built-in auxiliary input or the auxiliary input of optional
KCA-S220A is used.
|
38
English
Other than Standby mode
Other than Standby mode
Audio Preset Memory
Audio Preset Recall
Registering the value setup by Sound Control. The
memory cannot be erased by the Reset button.
Recalling the sound setup registered by <Audio
Preset Memory> (page 39).
1 Setup Sound Control
Refer to the following operations to setup the
Sound Control.
1 Select the source
Press the [SRC] button.
Refer to <Selecting the Source> (page 7).
- <Audio Control> (page 8)
- <Audio Setup> (page 9)
2 Enter Menu mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 10).
2 Enter Menu mode
Using the Control knob, select "MENU".
For the operation method, refer to <Function
Control mode> (page 10).
"MENU" is displayed.
3 Select Audio Preset mode
Turn the Control knob.
"MENU" is displayed.
3 Select Audio Preset mode
Turn the Control knob.
Select the "Audio Preset" display.
Select the "Audio Preset" display.
4 Enter Audio Preset mode
Press the Control knob for at least 1 second.
4 Enter Audio Preset mode
5 Select the Audio Preset Recall
Turn the Control knob.
Press the Control knob for at least 1 second.
5 Select the Audio Preset Memory
Turn the Control knob.
Select the "Memory" display.
Select the "Recall" display.
6 Determine whether to recall the Audio Preset
Press the Control knob.
6 Determine whether to put the Audio Preset in
the memory
Press the Control knob.
"Recall?" is displayed.
7 Recall the Audio Preset
Select "YES" using the Control knob.
"Recall Completed" is displayed.
"Memory?" is displayed.
7 Put the Audio Preset in the memory
Select "YES" using the Control knob.
"Memory Completed" is displayed.
8 Exit Audio Preset mode
Press the [FNC] button.
⁄
8 Exit Audio Preset mode
•
The User memory of "SYSTEM Q" in <Audio Control>
(page 8) is changed to the value which was recalled.
The source tone memory item of <Audio Control> (page
8) is changed to the value which was recalled by the
selected source.
Press the [FNC] button.
•
⁄
•
•
•
Register 1 pair of Audio Preset Memory. You cannot
register by the source.
When you press the Reset, all the sources will be the
setting value which is registered.
The following items cannot be registered.
Volume, Balance, Fader, Loudness, Volume offset, Dual
Zone System, Rear Volume
English
|
39
Menu system
Function of KDC-X791/KDC-MP735U
In Standby mode
Firmware version display
Displaying the firmware version with the unit.
Turn the Control knob.
Select the "F/W Version : " display.
In Standby mode
Demonstration mode Setting
Sets the demonstration mode.
1 Select the Demonstration mode
Turn the Control knob.
Select the "DEMO Mode" display.
2 Set the Demonstration mode
Press the Control knob for at least 2 seconds.
Each time you press the knob at least 2 seconds,
the Demonstration mode alternates between the
settings shown in the table below.
Display
Setting
"DEMO Mode : ON"
The Demonstration mode function is ON.
"DEMO Mode : OFF" Exit Demonstration mode (Normal mode).
|
40
English
Basic Operations of remote control
SRC
ATT
VOL
SRC
AT T
VOL
AUD
AUD
FM/AM/+/–
2-ZONE
DIRECT
[0] — [9]
: This button is used when Kenwood Bluetooth
HANDS FREE BOX is connected. For more
information, refer to the instruction manual of
Bluetooth HANDS FREE BOX.
Loading and Replacing the battery
Basic operations
Use two "AA"/ "R6"-size batteries.
Slide the cover while pressing downwards to
remove it as illustrated.
Insert the batteries with the + and – poles aligned
properly, following the illustration inside the case.
[VOL] buttons
Adjusts the volume.
[SRC] button
Each time you press the button, the source
alternates.
For the source alternating order refer to <Selecting
the Source> (page 7).
[ATT] button
Turns the volume down quickly.
When the button is pressed again, the volume
returns to the previous level.
2WARNING
•
Store unused batteries out of the reach of children.
Contact a doctor immediately if the battery is
accidentally swallowed.
¤
•
Do not set the remote control in hot places such as on
the dashboard.
English
|
41
Basic Operations of remote control
Audio Control
In Disc/USB source
[AUD] button
Selects the Audio item to be adjusted.
[4]/ [¢] buttons
Going forwards and backwards between music.
[VOL] buttons
Adjusts the Audio item.
[+]/ [–] buttons
Going forwards and backwards between disc/
folders.
⁄
•
Refer to <Audio Control> (page 8) for the operation
method, such as the procedures for Audio control and
others operations.
[38] button
Each time you press the button, the music is played
or paused.
•
The remote control can only select and adjust the Basic
Audio item. Selecting and adjusting of the Detail Audio
item cannot be done.
[0] — [9] buttons
When in <Direct Music Search> (page 25) and
<Direct Disc Search> (page 25), enters the music/
disc number.
Dual Zone System
[2-ZONE] button
Each time you press the button, "2 ZONE" of
In Satellite radio source
<Audio Setup> (page 9) is turned ON or OFF.
[FM] button
Selects the preset band.
[5]/ [∞] buttons
Adjusts the volume of the rear channel.
The rear channel activates while the Dual Zone
System is ON.
[4]/ [¢] buttons
Searches up or down channels.
[0] — [9] buttons
Press buttons [1] — [6] to recall preset channels.
[DIRECT] button
Enters and cancels the <Direct Access Tuning>
(page 22) mode.
In Tuner source
[FM]/ [AM] buttons
Selects the band.
Each time you press the [FM] button, the band
alternates between the FM1, FM2, and FM3 bands.
In HD Radio source
[4]/ [¢] buttons
[FM] button
Selects the HD FM band.
Each time you press the [FM] button, the band
alternates between the HF1, HF2, and HF3 bands.
Tune up or down band.
[0] — [9] buttons
Press buttons [1] — [6] to recall preset stations.
[DIRECT] button
Enters and cancels the <Direct Access Tuning>
(page 22) mode.
[AM] button
Selects the HD AM band.
[4]/ [¢] buttons
Tunes up or down bands.
[0] — [9] buttons
Press buttons [1] — [6] to recall preset stations.
|
42
English
Accessories/ Installation Procedure
Accessories
¤
•
If the power is not turned ON ("Protect" is displayed), the
speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
1
..........1
•
If your car’s ignition does not have an ACC position, connect
the ignition wires to a power source that can be turned on
and off with the ignition key. If you connect the ignition
wire to a power source with a constant voltage supply, as
with battery wires, the battery may die.
2
..........2
•
•
If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when closing and opening.
If the fuse blows, first make sure the wires aren’t touching
to cause a short circuit, then replace the old fuse with one
with the same rating.
Insulate unconnected wires with vinyl tape or other similar
material. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires or the terminals.
Connect the speaker wires correctly to the terminals to
which they correspond. The unit may be damaged or fail to
work if you share the - wires or ground them to any metal
part in the car.
3
..........4
4
•
•
..........4
5
..........2
•
When only two speakers are being connected to the
system, connect the connectors either to both the front
output terminals or to both the rear output terminals (do
not mix front and rear). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
After the unit is installed, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
Mount the unit so that the mounting angle is 30° or less.
6
..........1
7
•
•
..........1
If You Want to Connect iPod
Installation Procedure
1. To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2. Make the proper input and output wire
connections for each unit.
AUX input
3. Connect the speaker wires of the wiring harness.
4. Connect the wiring harness wires in the following
order: ground, battery, ignition.
iPod
AUDIO OUT
KCA-iP200 (Optional accessory)
5. Connect the wiring harness connector to the unit.
6. Install the unit in your car.
7. Reconnect the - battery.
•
•
No other optional accessory can be connected because
the USB connector and the AUX input are used for iPod
connection.
Dual Zone System in <Audio Setup> (page 9) will become
unavailable.
8. Press the reset button.
2WARNING
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
|
English
43
Connecting Wires to Terminals
Tape
Front left output (White)
Front right output (Red)
Rear left output (White)
Steering remote control
FRONT
REAR
(Light Blue/Yellow)
To USB device
(KDC-X791 only)
USB connector (1m)
REMO.CONT
Rear right output (Red)
(KDC-X791/MP735U only)
To use the steering wheel
remote control feature,
you need to an exclusive
Sub Woofer left output (White)
Sub Woofer right output (Red)
SUB
WOOFER
Do not remove the cap
when you do not use the
USB cable. The connector
will cause the unit to
malfunction if it gets in
touch with any metallic
part of the vehicle.
• Fasten the connector
with the tape so that the
cable will not come off.
remote adapter (not
supplied) matches your
car is required.
FM/AM antenna input
AUX input (Stereo)
Use the mini-plug which is stereo type and does
not have any resistance.
(KDC-X791/MP735U only)
Fuse (10A)
To Kenwood disc changer/ External optional accessory
To connect these leads, refer to the relevant instruction
manuals.
Wiring harness
(Accessory1)
White
To front left speaker
To front right speaker
To rear left speaker
To rear right speaker
White/Black
Gray
FRONT L
FRONT R
REAR L
Gray/Black
Green
Green/Black
Purple
Purple/Black
REAR R
If no connections are made, do not let the wire come out from the tab.
Power control wire (Blue/White)
When using the optional power amplifier, connect to its power
control terminal.
P.CONT
Depending on what antenna you are using, connect either to the
control terminal of the motor antenna, or to the power terminal
for the booster amplifier of the film-type antenna.
Motor antenna control wire (Blue)
ANT.
CONT
TEL mute wire (Brown)
Connect to the terminal that is grounded when either the
telephone rings or during conversation.
MUTE
To connect the Kenwood navigation system, consult your
navigation manual.
Dimmer control wire (Orange / White)
To car light control switch
ILLUMI
External amplifier control wire (Pink/Black)
To "EXT.AMP.CONT." terminal of the amplifier
having the external amp control function.
(KDC-X791 only)
EXT.
CONT
Car fuse
box
Ignition key
switch
Ignition wire (Red)
ACC
Battery wire (Yellow)
Car fuse box
(Main fuse)
Ground wire (Black) · (To car chassis)
+ Battery
–
|
44
English
Installation
non-Japanese cars
Japanese cars
1 Refer to the section <Removing the hard rubber
Metal mounting strap
(commercially available)
frame> and then remove the hard rubber frame.
2 Align the holes in the unit (two locations on each
side) with the vehicle mounting bracket and secure
the unit with the accessory screws.
Firewall or metal support
T
N
T/N
T
N
T: Toyota cars
N: Nissan cars
Bend the tabs of the
mounting sleeve with a
screwdriver or similar utensil
and attach it in place.
8 mm
MAX.
8mm
MAX.
Self-tapping screw
(commercially available)
3
4
ø5mm
ø5mm
Accessory3...for Nissan car
Accessory4 ...for Toyota car
Screw (M4X8)
(commercially available)
¤
⁄
•
During installation, do not use any screws except for
those provided. The use of different screws might result in
damage to the main unit.
•
Make sure that the unit is installed securely in place. If the
unit is unstable, it may malfunction (for example, the sound
may skip).
•
Damage may occur if a screwdriver or similar tool is used
with excessive force during the installations.
|
English
45
Installation
Removing the hard rubber frame
Screwing the Faceplate on the Unit
If you want to fasten the faceplate to the main unit
so that it does not fall off.
1 Engage the catch pins on the removal tool and
remove the two locks on the upper level.
Upper the frame and pull it forward as shown in
the figure.
1 Refer to the section <Removing the hard rubber
frame> and then remove the hard rubber frame.
2 Drop open the faceplate by pressing the Release
button.
3 Tighten the screw (ø2 × 5 mm) (Accessory 5) and
bracket (Accessory6 ) in the hole shown on the
diagram.
Lock
Catch
Accessory2
Removal tool
Accessory6
2 When the upper level is removed, remove the
Accessory5
lower two locations.
⁄
•
The frame can be removed from the bottom side in the
same manner.
Removing the Unit
1 Refer to the section <Removing the hard rubber
4 Tighten the screw (ø2 × 5 mm) (Accessory 5) and
bracket (Accessory7) in the hole shown on the
diagram.
frame> and then remove the hard rubber frame.
2 Remove the screw (M4 × 8) on the back panel.
3 Insert the two removal tools deeply into the slots
on each side, as shown.
4 Lower the removal tool toward the bottom, and
pull out the unit halfway while pressing towards
the inside.
Accessory7
Accessory5
Screw (M4X8)
(commercially available)
Accessory2
¤
•
Never insert the screws in any other screw hole than the
one specified. If you screw them in another hole, it will
contact and may cause damage to the mechanical parts
inside the unit.
¤
•
Be careful to avoid injury from the catch pins on the
removal tool.
5 Pull the unit all the way out with your hands, being
careful not to drop it.
|
46
English
Troubleshooting Guide
Some functions of this unit may be disabled by
some settings made on this unit.
What might seem to be a malfunction in your unit
may just be the result of slight misoperation or
miswiring. Before calling service, first check the
following table for possible problems.
!
!
Cannot switch to Aux source.
• AUX is not turned on. ☞ <Built-in Auxiliary input
Setting> (page 38)
• AUX cannot be used when the KCA-iP200 is
connected.
General
? The Touch Sensor Tone doesn’t sound.
✔
The preout jack is being used.
☞
The Touch Sensor Tone can’t be output from the
preout jack.
• Cannot set up the subwoofer.
• Cannot set up subwoofer phase.
• No output from the subwoofer.
• Cannot set up the low pass filter.
• <Subwoofer Output> (page 10) is not set to On.
Tuner source
? Radio reception is poor.
• The Dual zone function is enabled. ☞ <Audio
Setup> (page 9)
✔
✔
The car antenna is not extended.
☞
Pull the antenna out all the way.
The antenna control wire is not connected.
!
• Cannot set up the high pass filter.
• Cannot set up the Fader.
☞
Connect the wire correctly, referring to the
section on <Connecting Wires to Terminals>
(page 44).
The Dual zone function is enabled. ☞ <Audio
Setup> (page 9)
Disc source
!
!
Cannot set up the subwoofer phase.
Low pass filter is set to Through. ☞ <Audio Setup>
(page 9)
? The specified disc does not play, but another one
plays instead.
✔
✔
The specified CD is quite dirty.
Clean the CD.
The disc is loaded in a different slot from that
specified.
☞
• Cannot select the output destination of the
subsource in the Dual zone.
• Cannot adjust the volume of the rear speakers.
The Dual zone function is disabled. ☞ <Audio
Setup> (page 9)
☞
Eject the disc magazine and check the number
for the specified disc.
✔
The disc is severely scratched.
Try another disc instead.
☞
!
!
No Audio control effect on AUX.
The Dual zone function is enabled. ☞ <Audio
Setup> (page 9)
Audio file source
? The sound skips when an Audio file is being
• Cannot register a security code.
• Cannot set up Display Illumination Control.
<Demonstration mode Setting> (page 40) is not
turned off.
played.
✔
The media is scratched or dirty.
☞
Clean the media, referring to the CD cleaning of
the section on <Handling CDs> (page 6).
✔
✔
The audio file is broken or not supported.
Damaged and unsupported files are skipped.
The recording condition is bad.
!
!
Cannot play audio files.
☞
<CD Read Setting> (page 38) is set to "2".
☞
Record the media again or use another media.
• Cannot File select.
• Cannot direct music serch.
The Random play function is enabled.
|
English
47
Troubleshooting Guide
HD Radio source
The messages shown below display your
systems condition.
? No sound can be heard, or the volume is low.
✔
The preset broadcast station is not transmitting in
the mode that was set with <Receive mode Setting>
(page 37).
Eject:
• No disc magazine has been loaded in
the changer. The disc magazine is not
completely loaded.
☞
Please set <Receive mode Setting> to "Auto".
• No CD in the unit.
✔
In digital AM broadcasting, receive mode switches
between stereo and monaural too often.
No Disc:
No disc has been loaded in the disc
magazine.
☞
Receiving condition is bad or unstable. Stereo is
chosen when receiving condition is good, and
it switches to monaural when the condition
becomes bad.
TOC Error:
• No disc has been loaded in the disc
magazine.
• The CD is quite dirty. The CD is upside-
down. The CD is scratched a lot.
✔
HD Radio tuner is connected to KCA-S220A or other
units.
☞
Connect the HD Radio tuner directly to this unit.
Read Error:
• The number of files or folders which are
stored in the connected USB device is above
the limitation.
• The file system of the connected USB device
is broken.
➪ Copy the files and folders for the USB
kenwood.com/usb/. If the error message is
still displayed, initialize the USB device or
use other USB devices.
USB device source
? The USB device is not detected.
✔
The USB connector is disconnected.
☞
Connect the connector of the USB device
properly.
? The USB device does not play its audio files.
The USB connector is disconnected.
✔
☞
Connect the connector of the USB device
properly.
Error 05:
The disc is unreadable.
Blank Disc:
No Track:
Nothing has been recorded on the MD.
No tracks are recorded on the MD, although it
has a title.
Error 15:
No Panel:
Error 77:
Media was played that doesn’t have data
recorded that the unit can play.
The faceplate of the slave unit being
connected to this unit has been removed.
The unit is malfunctioning for some reason.
➪ Press the reset button on the unit. If the
"Error 77" code does not disappear, consult
your nearest service center.
Mecha Error: Something is wrong with the disc magazine.
Or the unit is malfunctioning for some reason.
➪ Check the disc magazine. And then press
the reset button on the unit. If the "Mecha
Error" code does not disappear, consult
your nearest service center.
|
48
English
Hold Error:
The protective circuit in the unit activates
when the temperature inside the automatic
disc changer exceeds 60°C (140°F), stopping
all operation.
➪ Cool down the unit by opening the
windows or turning on the air conditioner.
As the temperature falls below 60°C
(140°F), the disc will start playing again.
No Device:
N/A Device:
The USB device is selected as a source
although no USB device is connected.
➪ Change the source to any source other
than USB. Connect an USB device, and
change the source to USB again.
An unsupported USB device is connected.
➪ For the supported USB devices, refer to
<http://www.kenwood.com/usb/>.
No Name:
Waiting:
Load:
Attempted to display DNPS during the CD
play having no disc names preset.
No Music Data/ Error 15:
• The connected USB device contains no
Text for the Satellite Radio tuner source is
being received.
playable audio file.
• Media was played that doesn’t have data
recorded that the unit can play.
Discs are being exchanged in the Disc
changer.
USB Error:
The connected USB device is rated a current
capacity higher than the allowable limit.
➪ Check the USB device with reference to
<http://www.kenwood.com/usb/>.
Some trouble may have occurred to the
connected USB device.
Reading:
IN (Blink):
The unit is reading the data on the disc.
The CD player section is not operating
properly.
➪ Reinsert the CD. If the CD cannot be
ejected or the display continues to flash
even when the CD has been properly
reinserted, please switch off the power
and consult your nearest service center.
➪ Change the source to any source other
than USB. Remove the USB device.
iPod Error:
Connection to the iPod has failed.
➪ Remove the USB device and then
reconnect it.
Protect (Blink): The speaker wire has a short-circuit or
touches the chassis of the vehicle, and then
the protection function is activated.
➪ Confirm that the software for the iPod is
the latest version.
➪ Wire or insulate the speaker cable properly
and press the reset button. If the "Protect"
code does not disappear, consult your
nearest service center.
USB REMOVE: The Remove mode has been selected for the
USB device. You can remove the USB device
safely.
Unsupported File:
An Audio file is played with a format that this
unit can’t support.
➪ ----
Copy Protection:
A copy-protected file is played.
➪ ----
DEMO MODE (Blink):
The Demonstration mode has been selected.
➪ The <Demonstration mode Setting> (page
40) is ON. Turn it OFF.
|
English
49
Specifications
Specifications subject to change without notice.
FM tuner section
USB Interface (KDC-X791/MP735U)
Frequency range (200 kHz space)
: 87.9 MHz – 107.9 MHz
USB Standard
: USB1.1/ 2.0
Usable sensitivity (S/N = 30dB)
: 9.3dBf (0.8 μV/75 Ω)
Quieting Sensitivity (S/N = 50dB)
: 15.2dBf (1.6 μV/75 Ω)
Maximum Supply current
: 500 mA
File System
: FAT16/ 32
Frequency response ( 3 dB)
: 30 Hz – 15 kHz
Signal to Noise ratio (MONO)
: 70 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
Selectivity ( 400 kHz)
: ≥ 80 dB
Stereo separation (1 kHz)
: 40 dB
AAC decode
: AAC-LC ".m4a" files
WAV signal
: Linear-PCM
AM tuner section
Audio section
Frequency range (10 kHz space)
: 530 kHz – 1700 kHz
Maximum output power
: 50 W x 4
Usable sensitivity (S/N = 20dB)
: 28 dBμ (25 μV)
Full Bandwidth Power (at less than 1% THD)
: 22 W x 4
Speaker Impedance
: 4 – 8 Ω
CD player section
Laser diode
: GaAlAs
Digital filter (D/A)
: 8 Times Over Sampling
D/A Converter
: 1 Bit
Spindle speed
: 1000 – 400 rpm (CLV 2times)
Wow & Flutter
: Below Measurable Limit
Tone action
Bass : 100 Hz 8 dB
Middle : 1 kHz 8 dB
Treble : 10 kHz 8 dB
Preout level / Load (during disc play)
: 4000 mV/10 kΩ (KDC-X791)
: 2500 mV/10 kΩ (KDC-MP735U/MP635)
Preout impedance
: ≤ 80 Ω (KDC-X791)
: ≤ 600 Ω (KDC-MP735U/MP635)
Frequency response ( 1 dB)
: 10 Hz – 20 kHz
Auxiliary input
Total harmonic distortion (1 kHz)
: 0.008 % (KDC-X791)
: 0.010 % (KDC-MP735U/MP635)
Signal to Noise ratio (1 kHz)
: 110 dB (KDC-X791/MP735U)
Frequency response ( 1 dB)
: 20 Hz – 20 kHz
Input Maximum Voltage
: 1200 mV
Input Impedance
: 100 kΩ
: 105 dB (KDC-MP635)
Dynamic range
: 93 dB
MP3 decode
: Compliant with MPEG-1/2 Audio Layer-3
WMA decode
: Compliant with Windows Media Audio
AAC decode
: AAC-LC ".m4a" files
General
Operating voltage (11 – 16V allowable)
: 14.4 V
Current consumption
: 10 A
Installation Size (W x H x D)
: 182 x 53 x 155 mm
WAV signal
: Linear-PCM (KDC-X791/MP735U)
7-3/16 x 2-1/16 x 6-1/8 inch
Weight
: 3.1 lbs (1.4 kg)
|
50
English
|