Kenwood KDC MP5029 User Manual

CD-RECEIVER  
KDC-MP6029  
KDC-MP5029  
INSTRUCTION MANUAL  
© B64-2950-00/00 (MW)  
Safety precautions  
About CD players/disc changers  
connected to this unit  
KENWOOD disc changers/ CD players released in  
1998 or later can be connected to this unit.  
Refer to the catalog or consult your Kenwood  
dealer for connectable models of disc changers/  
CD players.  
2WARNING  
To prevent injury or fire, take the  
following precautions:  
• To prevent a short circuit, never put or leave any  
metallic objects (such as coins or metal tools)  
inside the unit.  
Note that any KENWOOD disc changers/ CD players  
released in 1997 or earlier and disc changers made  
by other makers cannot be connected to this unit.  
Unsupported connection may result in damage.  
Setting the "O-N" Switch to the "N" position for the  
applicable KENWOOD disc changers/ CD players.  
The functions that can be used and the information  
that can be displayed will differ depending on the  
models being connected.  
Attach the panel while you are on the  
vehicle  
The panel lock arm will be appeared when the  
panel is removed. Therefore, the panel must be  
attached during the driving.  
2CAUTION  
To prevent damage to the machine, take  
the following precautions:  
• Make sure to ground the unit to a negative 12V  
DC power supply.  
You can damage both your unit and the CD changer if  
you connect them incorrectly.  
Lens Fogging  
• Do not install the unit in a spot exposed to direct  
sunlight or excessive heat or humidity. Also avoid  
places with too much dust or the possibility of  
water splashing.  
• Do not set the removed faceplate or the faceplate  
case in areas exposed to direct sunlight, excessive  
heat or humidity. Also avoid places with too much  
dust or the possibility of water splashing.  
Right after you turn on the car heater in cold  
weather, dew or condensation may form on  
the lens in the CD player of the unit. Called lens  
fogging, CDs may be impossible to play. In such  
a situation, remove the disc and wait for the  
condensation to evaporate. If the unit still does  
not operate normally after a while, consult your  
Kenwood dealer.  
• To prevent deterioration, do not touch the  
terminals of the unit or faceplate with your  
fingers.  
• Do not subject the faceplate to excessive shock,  
as it is a piece of precision equipment.  
• When replacing a fuse, only use a new one with  
the prescribed rating. Using a fuse with the wrong  
rating may cause your unit to malfunction.  
• Do not apply excessive force to the open  
faceplate or place objects on it. Doing so will  
cause damage or breakdown.  
• Do not use your own screws. Use only the screws  
provided. If you use the wrong screws, you could  
damage the unit.  
Do Not Load 8 cm (3 in.) CDs in the CD  
slot  
If you try to load a 8 cm (3 in.) CD with its adapter  
into the unit, the adapter might separate from the  
CD and damage the unit.  
The "AAC" logo is trademark of Dolby  
Laboratories.  
English  
|
3
Notes  
• If you experience problems during installation,  
consult your Kenwood dealer.  
• If the unit fails to operate properly, press the Reset  
button. The unit returns to factory settings when  
the Reset button is pressed.  
• Press the reset button if the disc auto changer fails  
to operate correctly. Normal operation should be  
restored.  
About DAB Tuner control  
Refer to A group on the Instruction manual of DAB  
Tuner KTC-9090DAB (optional accessory) for the  
control method of DAB Tuner function.  
However, the following control methods of the  
function for this unit may be differed from the  
Instruction manual; therefore, refer to the following  
supplemental instruction.  
<Auto Ensemble Memory Entry>  
1. Select the preset band for Auto Ensemble  
Memory Entry.  
2. Press the [AME] button for at least 2 seconds.  
Open Auto Ensemble Memory Entry.  
After storing in the memory finishes, the  
number of the pre-set buttons and the  
ensemble label are displayed.  
<Searching by programme type and language>  
and <Languages to be displayed>  
Reset button  
• The characters which can be displayed by this  
unit are A-Z 0-9 @ " ‘ ` % & * + – = , . / \ < > [ ] ( ) : ;  
^ - { } | ~ .  
• The illustrations of the display and the panel  
appearing in this manual are examples used to  
explain more clearly how the controls are used.  
Therefore, what appears on the display in the  
illustrations may differ from what appears on  
the display on the actual equipment, and some  
of the illustrations on the display may represent  
something impossible in actual operation.  
At the operation to press [DISP] button, press  
[AUTO] button.  
<Automatic Switching DAB priority>  
This function cannot be used.  
The marking of products using lasers  
(Except for some areas)  
Cleaning the Unit  
CLASS 1  
LASER PRODUCT  
If the faceplate of this unit is stained, wipe it with a  
dry soft cloth such as a silicon cloth.  
If the faceplate is stained badly, wipe the stain off  
with a cloth moistened with neutral cleaner, then  
wipe neutral detergent off.  
The label is attached to the chassis/case and says  
that the component uses laser beams that have  
been classified as Class 1. It means that the unit  
is utilizing laser beams that are of a weaker class.  
There is no danger of hazardous radiation outside  
the unit.  
Applying spray cleaner directly to the unit may affect its  
mechanical parts. Wiping the faceplate with a hard cloth  
or using a volatile liquid such as thinner or alcohol may  
scratch the surface or erases characters.  
Cleaning the Faceplate Terminals  
If the terminals on the unit or faceplate get dirty,  
wipe them with a dry, soft cloth.  
|
4
English  
About CDs  
Handling CDs  
• Don’t touch the recording surface of the CD.  
Removing CDs  
When removing CDs from this unit pull them out  
horizontally.  
CDs that can’t be used  
• CDs that aren’t round can’t be used.  
• CD-R and CD-RW are easier to damage than a  
normal music CD. Use a CD-R or a CD-RW after  
reading the caution items on the package etc.  
• Don’t stick tape etc. on the CD.  
Also, don’t use a CD with tape stuck on it.  
• CDs with coloring on the recording surface or that  
are dirty can’t be used.  
• This unit can only play the CDs with  
When using a new CD  
If the CD center hole or outside rim has burrs, use it  
after removing them with a ball pen etc.  
.
It may not correctly play discs which do not have  
the mark.  
• A CD-R or CD-RW that hasn’t been finalized can’t  
be played. (For the finalization process refer to  
your CD-R/CD-RW writing software, and your CD-  
R/CD-RW recorder instruction manual.)  
Burrs  
Burrs  
CD storage  
• Don’t place them in direct sunlight (On the seat  
or dashboard etc.) and where the temperature is  
high.  
• Store CDs in their cases.  
CD accessories  
Don’t use disc type accessories.  
CD cleaning  
Clean from the center of the disc and move  
outward.  
English  
|
5
About AAC, MP3 and WMA  
The playable AAC/MP3/WMA file (hereafter called  
Audio file) and the media format has the following  
limitation. The Audio file, which is out of the  
specification, may not able to be played normally,  
or the file and folder names may not be displayed  
correctly.  
MP3 ID3 Tag/ WMA Contents property:  
30 characters  
File/Folder name is the number of the characters  
including the extensions  
MP3 ID3 Tag can only display the tag of Ver1.X.  
Playable Audio file  
Limitation of structure for the file and the  
folder  
• Maximum number of directory levels: 8  
AAC, MP3, WMA: KDC-MP6029  
MP3, WMA: KDC-MP5029  
• Maximum number of folders:  
KDC-MP6029:100/KDC-MP5029:50  
• Maximum number of files per folder: 255  
• Maximum number of files and folders: 512 (KDC-  
MP5029 only)  
Attach the correct extension for the Audio file (AAC:  
".M4A", MP3: ".MP3", WMA: ".WMA")  
Do not attach the extensions to the other files besides  
the Audio file. If it is attached, the file, which is not the  
Audio file, will be played and outputs the loud noise, and  
then the speaker will be damaged.  
Playing order of the Audio file  
The Audio file is played in the order which is written  
by writing soft. You may be able to set the playing  
order by writing the play sequence numbers such  
as "01" to "99" at the beginning of the file name.  
The files with copy protection cannot be played.  
Playable AAC file  
".m4a" file encoded by AAC-LC format.  
for the details.  
Example  
0
¡
: Folder  
: Audio file  
CD  
(1)  
Playable MP3 file  
• MPEG 1/2 Audio Layer 3 file  
• Transfer bit rate: 8-320 kbps  
• Sampling frequency  
¡!  
2
¡"  
3
: 8, 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 kHz  
Playable WMA file  
¡#  
¡$  
• The file in accordance with Windows Media Audio  
(Except for the file for Windows Media Player 9 or  
after which applies the new functions)  
4
¡%  
• Transfer bit rate: 48-192 kbps  
• Sampling frequency: 32, 44.1, 48 kHz  
• Playing order  
Playing order after ¡! play.  
¡", ¡#, ¡$, ¡%...  
• File search  
Forward file search during ¡# play.  
Push the Control knob to [¢] ¡$  
• Folder search  
Forward folder search during ¡" play.  
Push the Control knob to [FM] 3, 4...  
• Folder select  
Playable media  
• CD-ROM, CD-R, CD-RW (CD-RW with quick format  
cannot be used.)  
When recording to the media up to the maximum  
capacity at once, the writing soft is set to "Disc at once".  
Playable disc format  
• ISO 9660 Level 1/2  
When it is set to directory 4, skip to the folder  
before the same level by folder select.  
Push the Control knob to [4] 2  
• Joliet  
• Romeo  
• Long file name.  
When it is set to directory 3, makes the level up  
by folder select.  
The maximum number of characters for  
display  
File/Folder name:  
Push the Control knob to [AM] 2  
KDC-MP6029:64 characters  
KDC-MP5029:64 (Joliet: 32) characters  
|
6
English  
General features  
VOL  
ATT/DIM  
Q
SRC  
Release button  
Control knob  
ATT indicator  
Clock display  
Power  
* Function of the KDC-MP6029  
Turning ON the Power  
Press the [SRC] button.  
When the power is ON, the <Security Code> (page  
20) is displayed as "CODE ON" or "CODE OFF".  
Volume  
Turning OFF the Power  
Press the [SRC] button for at least 1 second.  
Increasing Volume  
Turn the [VOL] knob clockwise.  
Decreasing Volume  
Turn the [VOL] knob counterclockwise.  
Selecting the Source  
Press the [SRC] button.  
Source required  
Tuner  
CD  
Display  
"TUNER"  
"CD"  
TV* (Optional accessory)  
External disc (Optional accessory)  
Auxiliary input (Optional accessory)  
Standby (Illumination only mode)  
"TV"  
"CD CH"  
"AUX EXT"  
"STANDBY"  
English  
|
7
General features  
Attenuator  
2 Enter Audio Control mode  
Press the [VOL] knob.  
Turning the volume down quickly.  
3 Select the Audio item for adjustment  
Press the [VOL] knob.  
Each time the knob is pressed, the items that can  
be adjusted switch as shown below.  
Press the [ATT] button.  
Each time the button is pressed, the Attenuator  
turns ON and OFF.  
When it’s ON, the "ATT" indicator blinks.  
4 Adjust the Audio item  
Turn the [VOL] knob.  
Adjustment Item Display  
Range  
–15 — +15  
–8 — +8  
–8 — +8  
–8 — +8  
System Q  
Subwoofer level *1*2 "SW L"  
You can recall the best sound setting preset for  
different types of music.  
Bass level  
Middle level  
Treble level  
Balance  
"BAS L"  
"MID L"  
"TRE L"  
"BAL"  
1 Select the source to set  
Press the [SRC] button.  
Left 15 — Right 15  
Rear 15 — Front 15  
Fader  
"FAD"  
2 Select the Sound type  
Press the [Q] button.  
When the button is pressed once, the current  
sound setting is displayed.  
Each time the button is pressed, the sound  
setting switches.  
*1 You can control this item when <Subwoofer  
Output> (page 9) is set to "SW ON".  
*2 Function of the KDC-MP6029  
5 Exit Audio Control mode  
Press any button.  
Press the button which is not [VOL] knob and  
[ATT] button.  
Sound setting  
Natural  
User memory*  
Rock  
Pops  
Easy  
Display  
"NATURAL"  
"USER"  
"ROCK"  
"POPS"  
"EASY"  
Top 40  
Jazz  
"TOP40"  
"JAZZ"  
Audio Setup  
Setting the Sound system, such as Cross over  
Network.  
*User memory: The values set on the <Audio Control>  
(page 8).  
1 Select the source for adjustment  
Press the [SRC] button.  
KDC-MP5029 doesn't have the User memory function  
so the values of Bass, Middle, and Treble set in audio  
control are replaced to the System Q values and  
"USER" is not be displayed when the System Q setting  
is changed.  
Each setting value is changed with the <Speaker  
Setting> (page 9).  
First, select the speaker type with the Speaker setting.  
2 Enter Audio Setup mode  
Press the [VOL] knob for at least 1 second.  
3 Select the Audio Setup item for adjustment  
Press the [VOL] knob.  
Each time the knob is pressed, the items that can  
be adjusted switch as shown below.  
4 Setup the Audio item  
Turn the [VOL] knob.  
Audio Control  
1 Select the source for adjustment  
Press the [SRC] button.  
|
8
English  
Function of the KDC-MP6029  
Adjustment Item Display  
Range  
Subwoofer Output  
Front High Pass  
Filter *2  
"HPF"  
"HPR"  
"LPF"  
Through/80/100/120/150  
/180 Hz  
Turning the Subwoofer output ON or OFF.  
Rear High Pass  
Through/80/100/120/150  
/180 Hz  
60/80/120/Through Hz  
Filter *2  
Hold down on [AM] of the Control knob for at  
least 1 second.  
Each time the button is pressed, Subwoofer  
output switches ON and OFF.  
Low Pass Filter*1*2  
Subwoofer Phase*1*2 "PHAS"  
Reverse (180°) / Normal (0°)  
Volume offset  
Loudness  
"V-OFF"  
"LOUD"  
–8 —  
ON/OFF  
0
When it’s ON, "SW ON" is displayed.  
Volume offset: Each source’s volume can be set as a  
difference from the basic volume.  
Loudness: Compensating for low and high tones  
during low volume.  
*1 You can control this item when <Subwoofer  
Output> (page 9) is set to "SW ON".  
*2 Function of the KDC-MP6029  
5 Exit Audio Setup mode  
Press [VOL] knob for at least 1 second.  
Speaker Setting  
Fine-tuning so that the System Q value is optimal  
when setting the speaker type.  
1 Enter Standby  
Press the [SRC] button.  
Select the "STANDBY" display.  
2 Enter Speaker Setting mode  
Press the [VOL] knob.  
3 Select the Speaker type  
Turn the [VOL] knob.  
Each time the knob is turned, the setting  
switches as shown below.  
Speaker type  
OFF  
For 5 & 4 in. speaker  
For 6 & 6x9 in. speaker  
For the OEM speaker  
Display  
"SP OFF"  
"SP 5/4"  
"SP 6*9/6"  
"SP OEM"  
4 Exit Speaker Setting mode  
Press the [VOL] knob.  
English  
|
9
General features  
Function of the KDC-MP5029  
Switching Display  
Dimmer Control  
Switching the information displayed.  
You can change the unit's display to dimmer.  
1 Enter Switching Display mode  
Press the Control knob for at least 1 second.  
"DISP SEL" is displayed.  
Press the [DIM] button for at least 1 second.  
Each time the button is pressed for 1 second, the  
Dimmer contol turns ON and OFF.  
2 Select the Display item  
Push the Control knob to [4] or [¢].  
When it’s ON, "DIM ON" is displayed.  
In Tuner source  
Information  
Frequency  
Clock  
Display  
"FREQ"  
"CLOCK"  
Theft Deterrent Faceplate  
The faceplate of the unit can be detached and  
taken with you, helping to deter theft.  
In CD & External disc source  
Removing the Faceplate  
Information  
Disc title*  
Track title*  
Track number & Play time  
Clock  
Display  
"D-TITLE"  
"T-TITLE"  
"P-TIME"  
"CLOCK"  
1 Press the Release button.  
Drop open the faceplate.  
2 Drawing the faceplate to left side pull it to  
the front and remove it.  
In Audio file source  
Information  
Display  
"TITLE"  
"ALBUM"  
"FOLDER"  
"FILE"  
Song title & Artist name*  
Album name & Artist name*  
Folder name  
File name  
Track number & Play time  
Clock  
"P-TIME"  
"CLOCK"  
The faceplate is a precision piece of equipment and  
can be damaged by shocks or jolts. For that reason,  
keep the faceplate in its special storage case while  
detached.  
Do not expose the faceplate or its storage case to  
direct sunlight or excessive heat or humidity. Also  
avoid places with too much dust or the possibility of  
water splashing.  
In Auxiliary input source  
Information  
Auxiliary input name  
Clock  
Display  
"SRC NAME"  
"CLOCK"  
3 Exit Switching Display mode  
Press the Control knob.  
Reattaching the Faceplate  
When LX-AMP is connected, the item setup by the  
Display mode of LX-AMP is displayed.(KDC-MP6029  
only)  
1 Align the shaft on the unit with the  
depression on the faceplate.  
* If the contents of the information cannot be  
displayed, Playtime is displayed.  
When the clock display is selected, the display setting  
of each source will be switched to the clock display.  
(KDC-MP5029 only)  
Album name cannot be displayed in WMA file.  
Song title, Artist name, and Album name cannot be  
displayed in AAC file.  
|
10  
English  
2 Push the faceplate in until it clicks.  
The faceplate is locked in place, allowing you to  
use the unit.  
TEL Mute  
The audio system automatically mutes when a  
call comes in.  
When a call comes in  
"CALL" is displayed.  
The audio system pauses.  
Listening to the audio during a call  
Press the [SRC] button.  
The "CALL" display disappears and the audio  
system comes back ON.  
When the call ends  
Hang up the phone.  
The "CALL" display disappears and the audio  
system comes back ON.  
English  
|
11  
Tuner/TV control features  
AUTO/  
AME  
SRC  
1 - 6  
Control knob  
ST indicator  
Band display  
Frequency display Preset station number  
Each time the button is pressed, the Tuning  
mode switches as shown below.  
Tuning  
Selecting the station.  
Tuning mode  
Display  
Operation  
Auto seek  
Preset station seek "AUTO 2"  
"AUTO 1"  
Automatic search for a station.  
Search in order of the stations  
in the Preset memory.  
1 Select tuner source  
Press the [SRC] button.  
Select the "TUNER" display.  
Manual  
"MANUAL" Normal manual tuning control.  
2 Select the band  
Push the Control knob to [FM] or [AM].  
Each time the knob is pushed to [FM], it switches  
between the FM1, FM2, and FM3 bands.  
Function of the KDC-MP6029  
Function of remote  
3 Tune up or down band  
Push the Control knob to [4] or [¢].  
Direct Access Tuning  
Entering the frequency and tuning.  
During reception of stereo stations the "ST" indicator  
is ON.  
1 Select the band  
Press the [FM] or [AM] button.  
2 Enter Direct Access Tuning mode  
Press the [DIRECT] button on the remote.  
"– – – –" is displayed.  
Tuning Mode  
Choose the tuning mode.  
3 Enter the frequency  
Press the number buttons on the remote.  
Press the [AUTO] button.  
|
12  
English  
Example:  
Frequency Step Setting  
Desired frequency  
92.1 MHz (FM)  
810 kHz (AM)  
Press button  
[0], [9], [2], [1]  
[0], [8], [1], [0]  
Changing the tuning frequency step.  
The original setting is FM band 50 kHz, and AM  
band 9 kHz.  
Canceling Direct Access Tuning  
Press the [DIRECT] button on the remote.  
1 Turn the power OFF  
Press the [SRC] button for at least 1 second.  
2 Switch the frequency step  
While pressing the [1] and [5] button, press  
the [SRC] button.  
Release your fingers from the button after the  
display is appeared.  
Station Preset Memory  
Putting the station in the memory.  
The frequency step changes to FM band 200 kHz,  
and AM band 10 kHz.  
1 Select the band  
Push the Control knob to [FM] or [AM].  
2 Select the frequency to put in the memory  
When the same operation is repeated, it returns to the  
original setting.  
When the frequency step is switched, the frequencies  
in the memory are deleted.  
Push the Control knob to [4] or [¢].  
3 Put the frequency in the memory  
Press the desired [1] — [6] button for at least  
2 seconds.  
The preset number display blinks 1 time.  
On each band, 1 station can be put in the  
memory on each [1] — [6] button.  
Function of the KDC-MP6029  
Function of LX BUS Television  
TV Tuning  
The TV channel of a connected LX BUS Television  
(optional accessory) can be selected.  
The action depends on the setting of the  
connected LX BUS Television. Refer to the user  
instruction of the LX BUS Television for details.  
Auto Memory Entry  
Putting stations with good reception in the  
memory automatically.  
1 Select the band for Auto Memory Entry  
1 Select TV source  
Press the [SRC] button.  
Select the "TV" display.  
Push the Control knob to [FM] or [AM].  
2 Open Auto Memory Entry  
Press the [AME] button for at least 2 seconds.  
When 6 stations that can be received are put in  
the memory Auto Memory Entry closes.  
2 Select the TV band and Video input  
Press the [FM] button.  
Each time the [FM] button is pressed, TV bands  
and Video input switch.  
3 Select the TV channel  
Push the Control knob to [4] or [¢].  
Preset Tuning  
Calling up the stations in the memory.  
1 Select the band  
Push the Control knob to [FM] or [AM].  
2 Call up the station  
Press the desired [1] — [6] button.  
English  
|
13  
Tuner/TV control features  
Function of the KDC-MP6029  
Function of LX BUS Television  
TV channel Preset Memory  
Putting the TV channels in the memory.  
1 Select the TV band  
Press the [FM] button.  
2 Select the TV channel to put in the memory  
Push the Control knob to [4] or [¢].  
3 Put the TV channel in the memory  
Press the desired [1] — [6] button for at least  
2 seconds.  
The preset number display blinks 1 time.  
On each band, 1 TV channel can be put in the  
memory on each [1] — [6] button.  
Function of the KDC-MP6029  
Function of LX BUS Television  
Preset TV Tuning  
Calling up the TV channels in the memory.  
1 Select the TV band  
Press the [FM] button.  
2 Call up the TV channel  
Press the desired [1] [6] button.  
Function of the KDC-MP6029  
Function of remote  
Direct TV Tuning  
Entering the TV channel and tuning.  
1 Select the TV band  
Press the [FM] button.  
2 Enter Direct TV Tuning mode  
Press the [DIRECT] button on the remote.  
"– –" is displayed.  
3 Enter the TV channel  
Press the number buttons on the remote.  
Example:  
Desired channel  
Press button  
8 ch  
[0], [8]  
Canceling Direct TV Tuning  
Press the [DIRECT] button on the remote.  
|
14  
English  
CD/Audio file/External disc control features  
Release button  
Control knob  
SCAN RDM/ REP F.SEL M.RDM  
3
SRC  
IN indicator  
Track number  
Track time  
Disc number  
When a disc is inserted  
Press the [SRC] button.  
Playing CD & Audio file  
Select the "CD" display.  
When there is no disc inserted  
Pause and play  
1 Drop open the faceplate  
Press the Control knob.  
Each time the knob is pressed, it pauses and  
plays.  
Press the Release button.  
2 Insert a disc.  
3 Push the faceplate on the left side, and return  
it to its former position.  
Eject the disc  
1 Drop open the faceplate  
Press the Release button.  
When the faceplate has been dropped open, it might  
interfere with the shift lever or something else. If this  
happens, pay attention to safety and move the shift  
lever or take an appropriate action, then operate the  
unit.  
Do not use the unit with the faceplate in the open  
condition. If it’s used in the open position dust can  
enter the inside part and cause damage.  
2 Eject the disc  
Press the [0] button.  
Refer to <About AAC, MP3 and WMA> (page6) for the  
Audio file by models which can be played.  
When a disc is inserted, the "IN" indicator is ON.  
3 Press the faceplate on the left side, and  
return it to its former position.  
English  
|
15  
CD/Audio file/External disc control features  
Function of disc changer/ Audio file  
Playing External Disc  
Disc Search/Folder Search  
Playing discs set in the optional accessory disc  
player connected to this unit.  
Selecting the disc set in the Disc changer or the  
folder recorded on the Audio file media.  
Press the [SRC] button.  
Select the display for the disc player you want.  
Display examples:  
Push the Control knob to [FM] or [AM].  
Display  
"CD CH"  
"MD CH"  
Disc player  
CD changer  
MD changer  
Function of remote  
Direct Track/File Search  
Pause and play  
Doing Track/File Search by entering the track/file  
number.  
Press the Control knob.  
Each time the knob is pressed, it pauses and  
plays.  
1 Enter the track/file number  
Press the number buttons on the remote.  
2 Do Track/File Search  
Disc 10 is displayed as "0".  
Press the [4] or [¢] button.  
The functions that can be used and the information  
that can be displayed will differ depending on the  
external disc players being connected.  
Canceling Direct Track/File Search  
Press the [38] button.  
Fast Forwarding and Reversing  
Function of disc changers with remote  
Direct Disc Search  
Fast Forwarding  
Hold down on [¢] of the Control knob.  
Release your finger to play the disc at that point.  
Doing Disc Search by entering the disc number.  
1 Enter the disc number  
Reversing  
Press the number buttons on the remote.  
Hold down on [4] of the Control knob.  
Release your finger to play the disc at that point.  
2 Do Disc Search  
Press the [+] or [] button.  
The sound is not output while the Audio file is being  
searched.  
Fast Forwarding and Reversing cannot be done while  
AAC file is being played.  
Canceling Direct Disc Search  
Press the [38] button.  
Input "0" to select disc 10.  
Track/File Search  
Track/File/Disc/Folder Repeat  
Searching for a song on the disc or in the Audio  
file folder.  
Replaying the song, disc in the Disc changer or  
Audio file folder you’re listening to.  
Push the Control knob to [4] or [¢].  
Press the [REP] button.  
Each time the button is pressed, the Repeat Play  
switches as shown below.  
|
16  
English  
In CD & External disc source  
Press the [M.RDM] button.  
Each time the button is pressed, the Magazine  
Random Play turns ON and OFF.  
When it’s ON, "MGZN RDM" is displayed.  
Repeat play  
Track Repeat  
Disc Repeat (In Disc Changer)  
OFF  
Display  
"TRAC REP"  
"DISC REP"  
"REP OFF"  
When the Control knob is pushed to [¢], the next  
random song starts.  
In Audio file  
Repeat play  
File Repeat  
Folder Repeat  
OFF  
Display  
"FILE REP"  
"FOLD REP"  
"REP OFF"  
Function of Audio file  
Folder Select  
Quickly selecting the folder you want to listen to.  
Scan Play  
1 Enter Folder Select mode  
Press the [F.SEL] button.  
"F-SELECT" is displayed.  
Playing the first part of each song on the disc  
or Audio file folder you are listening to and  
searching for the song you want to listen to.  
During Select mode the folder information is  
displayed as shown below.  
Folder name display  
1 Start Scan Play  
Press the [SCAN] button.  
"TRAC SCN"/"FILE SCN" is displayed.  
Displays the current folder name.  
2 Release it when the song you want to listen  
to is played  
Press the [SCAN] button.  
2 Select the folder level  
Push the Control knob to [FM] or [AM].  
With the [FM] of the Control knob, you move  
1 level down and with the [AM] of the Control  
knob 1 level up.  
Random Play  
Play all the songs on the disc or Audio file folder  
in random order.  
Selecting a folder in the same level  
Push the Control knob to [4] or [¢].  
With the [4] of the Control knob, you move  
to the previous folder, and with the [¢] of the  
Control knob to the next folder.  
Press the [RDM] button.  
Each time the button is pressed, Random Play  
turns ON and OFF.  
When it’s ON, "DISC RDM"/"FOLD RDM" is  
displayed.  
Returning to the top level  
Press the [3] button.  
When the Control knob is pushed to [¢], the next  
random song starts.  
3 Decide the folder to play  
Press the Control knob.  
The Folder Select mode releases, and the Audio  
file in the folder being displayed is played.  
Canceling the Folder Select mode  
Press the [F.SEL] button.  
Function of disc changer  
Magazine Random Play  
Play the songs on all the discs in the disc changer  
in random order.  
English  
|
17  
CD/Audio file/External disc control features  
Text/Title Scroll  
Scrolling the displayed CD text, Audio file text, or  
MD title.  
Hold down on [FM] of the Control knob for at  
least 1 second.  
|
18  
English  
Menu system  
Control knob  
MENU SRC  
Menu display  
Menu System  
4 Exit Menu mode  
Press the [MENU] button.  
Setting during operation beep sound etc.  
functions.  
The Menu system basic operation method is  
explained here. The reference for the Menu items  
and their setting content is after this operation  
explanation.  
When other items that are applicable to the basic  
operation method above are displayed, afterwards  
their setting content chart is entered. (Normally the  
uppermost setting in the chart is the original setting.)  
Also, the explanation for items that aren’t applicable  
(<Manual Clock Adjustment> etc.) are entered step  
by step.  
1 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
2 Select the menu item  
Push the Control knob to [FM] or [AM].  
Example: When you want to set the beep sound  
select the "BEEP" display.  
3 Set the menu item  
Push the Control knob to [4] or [¢].  
Example: When "BEEP" is selected, each time the  
knob is pushed it switches "BEEP ON"  
or "BEEP OFF". Select 1 of them as the  
setting.  
You can continue by returning to step 2 and  
setting other items.  
English  
|
19  
Menu system  
In Standby mode  
The unit can be used.  
Security Code  
If an incorrect code is input, "WAITING" is displayed,  
and the input prohibited time shown below is  
generated.  
After the input prohibited time lapses, "CODE" is  
displayed, and input can be done.  
Because authorization by the Security Code is  
required when it’s removed from the vehicle,  
personalizing this unit is by using the Security  
Code is a help in preventing theft.  
Number of times the  
incorrect code was input  
1
2
3
4
Input prohibited time  
When the Security Code function is activated, it can’t be  
released.  
Note, your Security Code is the 4 digit number entered in  
your "Car Audio Passport" in this package.  
5 minutes  
1 hour  
24 hours  
1 Enter Standby  
Press the [SRC] button.  
Select the "STANDBY" display.  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
When "MENU" is displayed, "SECURITY" is  
displayed.  
In Standby mode  
Touch Sensor Tone  
Setting the operation check sound (beep sound)  
ON/OFF.  
3 Enter Security Code mode  
Press the Control knob for at least 1 second.  
When "ENTER" is displayed, "CODE" is displayed.  
Display  
Setting  
"BEEP ON"  
"BEEP OFF"  
Beep is heard.  
Beep canceled.  
4 Select the digits to enter  
Push the Control knob to [4] or [¢].  
5 Select the Security Code numbers  
Push the Control knob to [FM] or [AM].  
6 Repeat steps 4 and 5, and complete the  
Security Code.  
In Standby mode  
Manual Clock Adjustment  
7 Confirm the Security Code  
Press the Control knob for at least 3 second.  
When "RE-ENTER" is displayed, "CODE" is  
displayed.  
1 Select Clock Adjustment mode  
Push the Control knob to [FM] or [AM].  
Select the "CLK ADJ" display.  
8 Do the step 4 through 7 step operation, and  
reenter the security code.  
"APPROVED" is displayed.  
2 Enter Clock Adjust mode  
Press the Control knob for at least 1 second.  
The clock display blinks.  
The Security Code function activates.  
3 Adjust the hours  
Push the Control knob to [FM] or [AM].  
If you enter a Code different from your Security Code,  
you have to start over from step 4.  
Adjust the minutes  
Push the Control knob to [4] or [¢].  
Press the Reset button and when its removed  
from the battery power source  
4 Exit Clock adjustment mode  
Press the [MENU] button.  
1 Turn the power ON.  
2 Do the step 4 through 7 step operation, and  
reenter the security code.  
"APPROVED" is displayed.  
|
20  
English  
In Standby mode  
Function of the KDC-MP6029  
When LX AMP unit connecting  
DSI (Disabled System Indicator)  
AMP Control  
A red indicator will blink on the unit after the  
faceplate is removed, warning potential thieves.  
You can control the LX AMP connected to the  
unit.  
Display  
"DSI ON"  
"DSI OFF"  
Setting  
LED flashes.  
LED OFF.  
1 Select AMP Control mode  
Push the Control knob to [FM] or [AM].  
Select the "AMP CTRL" display.  
2 Enter AMP Control mode  
Press the Control knob for at least 1 second.  
Function of the KDC-MP6029  
In Standby mode  
3 Select the AMP Control item for adjustment  
Push the Contol knob to [FM] or [AM].  
Selectable Illumination  
Selecting the button illumination color as green  
or red.  
For the details of the AMP Control item, see the  
Instruction manual attached to the LX AMP.  
4 Adjust the AMP Control item  
Display  
"KEY GRN"  
"KEY RED"  
Setting  
The illumination color is green.  
The illumination color is red.  
Push the Control knob to [4] or [¢].  
5 Exit AMP Control mode  
Press the [MENU] button.  
You cannot use the LX AMP operation during standby  
mode.  
Function of the KDC-MP6029  
In Standby mode  
Dimmer  
Dimming this unit’s display automatically when  
the vehicle light switch is turned ON.  
In FM reception  
CRSC (Clean Reception System  
Circuit)  
Display  
"DIM ON"  
"DIM OFF"  
Setting  
The display dims.  
The display doesn’t dim.  
Temporarily have reception switched from  
stereo to mono to reduce multi-path noise when  
listening to the FM station.  
Display  
"CRSC ON"  
"CRSC OFF"  
Setting  
The CRSC is ON.  
The CRSC is OFF.  
Function of the KDC-MP6029  
In Standby mode  
Built-in Amp Setting  
Built-in amplifier is controlled.  
Turning OFF this control enhances the preout  
quality.  
Strong electrical fields (such as from power lines) may  
cause unstable sound quality when CRSC is turned  
ON. In such a situation, turn it OFF.  
Display  
Setting  
"AMP ON"  
"AMP OFF"  
The built-in amplifier activates.  
The built-in amplifier deactivates.  
English  
|
21  
Menu system  
Auxiliary Input Display Setting  
Text Scroll  
For selecting the display when switched to  
Auxiliary input source.  
Setting the displayed text scroll.  
Display  
Setting  
1 Select Auxiliary input source  
Press the [SRC] button.  
"SCL AUTO"  
"SCL MANU"  
Repeats scroll.  
Scrolls when the display changes.  
Select the "AUX EXT" display.  
2 Enter Menu mode  
Press the [MENU] button for at least 1 second.  
"MENU" is displayed.  
The text scrolled is shown below.  
- CD text  
- Folder name/ File name/ Song title/ Artist name/  
Album name  
- MD title  
3 Select Auxiliary input display setting mode  
Push the Control knob to FM] or [AM].  
Select the "NAME SET" display.  
4 Enter Auxiliary input display setting mode  
Press the Control knob for at least 1 second.  
The presently selected Auxiliary input display is  
displayed.  
In Standby mode  
CD Read Setting  
5 Select the Auxiliary input display  
Push the Control knob to [4] or [¢].  
When there is a problem on playing a CD with  
special format, this setting play the CD by force.  
Each time the button is pressed, the display  
switches as shown below.  
• "AUX EXT"  
• "DVD"  
• "PORTABLE"  
• "GAME"  
Display  
"CD READ1"  
"CD READ2"  
Setting  
Play CD and Audio file.  
Play CD by force.  
• "VIDEO"  
• "TV"  
Setting "CD READ2" cannot play Audio file.  
Some music CDs may not be played back even in the  
"CD READ2" mode.  
6 Exit Auxiliary input display setting mode  
Press the [MENU] button.  
When operation stops for 10 seconds, the name at  
that time is registered, and the Auxiliary input display  
setting mode closes.  
The Auxiliary input display can be set only when the  
auxiliary input of optional KCA-S210A is used.  
|
22  
English  
Basic Operations of remote  
SRC  
ATT  
38  
VOL  
SRC  
ATT  
VOL  
38  
AUD  
AUD  
FM+  
AM–  
4
¢
4/¢  
FM/AM/+/–  
Not Used  
DIRECT  
/OK  
DIRECT/OK  
ABC  
JKL  
DEF  
GHI  
MNO  
WXY  
[0] — [9]  
PRS  
TUV  
QZ  
Loading and Replacing the battery  
Basic operations  
Use two "AA"-size batteries.  
Slide the cover while pressing downwards to  
remove it as illustrated.  
Insert the batteries with the + and – poles aligned  
properly, following the illustration inside the case.  
[VOL] buttons  
Adjusting the volume.  
[SRC] button  
Each time the button is pressed, the source  
switches.  
For the source switching order refer to <Selecting  
the Source> (page 7).  
[ATT] button  
Turning the volume down quickly.  
When it is pressed again, it returns to the  
previous level.  
2WARNING  
Store unused batteries out of the reach of children.  
Contact a doctor immediately if the battery is  
accidentally swallowed.  
Do not set the remote on hot places such as above  
the dashboard.  
English  
|
23  
Basic Operations of remote  
Accessory of the KDC-MP6029  
Audio Control  
In TV source  
[AUD] button  
Select the Audio item for adjustment.  
[FM] button  
Select the TV band and Video input.  
Each time the [FM] button is pressed, TV bands  
and Video input switch.  
[VOL] buttons  
Adjust the Audio item.  
[4]/ [¢] buttons  
Refer to <Audio Control> (page 8) for the operation  
method, such as the procedures of Audio control and  
others.  
Select the TV channel.  
[0] — [9] buttons  
Press buttons [1] — [6] to recall preset TV  
channels.  
In Tuner source  
[FM]/ [AM] buttons  
Select the band.  
Each time the [FM] button is pressed, it switches  
between the FM1, FM2, and FM3 bands.  
[4]/ [¢] buttons  
Tune up or down band.  
[0] — [9] buttons  
Press buttons [1] — [6] to recall preset stations.  
[DIRECT]/ [OK] button (KDC-MP6029)  
Enters and cancels the <Direct Access Tuning>  
(page 12) mode.  
In Disc source  
[4]/ [¢] buttons  
Doing track/file forward and backward.  
[+]/ [] buttons  
Doing disc/folder forward and backward.  
[38] button  
Each time the button is pressed, the song pauses  
and plays.  
[0] — [9] buttons  
When in <Direct Track/File Search> (page 16) and  
<Direct Disc Search> (page 16), enter the track/  
file/disc number.  
|
24  
English  
Accessories/ Installation Procedure  
2. Make the proper input and output wire  
connections for each unit.  
3. Connect the speaker wires of the wiring harness.  
4. Connect the wiring harness wires in the  
following order: ground, battery, ignition.  
Accessories  
1
5. Connect the wiring harness connector to the  
unit.  
..........1  
6. Install the unit in your car.  
7. Reconnect the - battery.  
8. Press the reset button.  
2
2WARNING  
..........2  
If you connect the ignition wire (red) and the battery wire  
(yellow) to the car chassis (ground), you may cause a short  
circuit, that in turn may start a fire. Always connect those  
wires to the power source running through the fuse box.  
3
..........4  
If the power is not turned ON (or it is ON, but will be OFF  
immediately), the speaker wire may have a short-circuit  
or touched the chasis of the vehicle and the protection  
function may have been activated. Therefore, the speaker  
wire should be checked.  
4
If your car’s ignition does not have an ACC position,  
connect the ignition wires to a power source that can be  
turned on and off with the ignition key. If you connect  
the ignition wire to a power source with a constant  
voltage supply, as with battery wires, the battery may die.  
If the console has a lid, make sure to install the unit so  
that the faceplate will not hit the lid when closing and  
opening.  
..........4  
5
..........1  
If the fuse blows, first make sure the wires aren’t touching  
to cause a short circuit, then replace the old fuse with  
one with the same rating.  
6
Insulate unconnected wires with vinyl tape or other  
similar material. To prevent a short circuit, do not remove  
the caps on the ends of the unconnected wires or the  
terminals.  
..........2  
Connect the speaker wires correctly to the terminals to  
which they correspond. The unit may be damaged or fail  
to work if you share the - wires or ground them to any  
metal part in the car.  
When only two speakers are being connected to the  
system, connect the connectors either to both the front  
output terminals or to both the rear output terminals  
(do not mix front and rear). For example, if you connect  
the + connector of the left speaker to a front output  
terminal, do not connect the - connector to a rear  
output terminal.  
7
..........1  
8
..........1  
After the unit is installed, check whether the brake lamps,  
blinkers, wipers, etc. on the car are working properly.  
Mount the unit so that the mounting angle is 30° or less.  
Installation Procedure  
1. To prevent a short circuit, remove the key from  
the ignition and disconnect the - battery.  
English  
|
25  
Connecting Wires to Terminals (KDC-MP6029)  
Front left output (White)  
Front right output (Red)  
Sub Woofer left output (White)  
Sub Woofer right output (Red)  
Rear left output (White)  
Rear right output (Red)  
FM/AM antenna input  
To connect these leads, refer to  
the relevant instruction manuals.  
To KENWOOD disc changer/External optional accessory  
Fuse (10A)  
Wiring harness  
(Accessory1)  
If no connections are made, do not let the wire come out from the tab.  
When using the optional power amplifier,  
connect to its power control terminal.  
Power control wire (Blue/White)  
P.CONT  
Depending on what antenna you are using,  
connect either to the control terminal of the  
motor antenna, or to the power terminal for the  
booster amplifier of the film-type antenna.  
Motor antenna control wire (Blue)  
TEL mute wire (Brown)  
ANT.  
CONT  
Connect to the terminal that is grounded  
when either the telephone rings or during  
conversation.  
MUTE  
To connect the KENWOOD navigation  
system, consult your navigation manual.  
Dimmer control wire (Orange / White)  
To car light control switch  
ILLUM  
White/Black  
White  
To front left speaker  
FRONT  
FRONT  
L
Gray/Black  
Gray  
To front right speaker  
To rear left speaker  
R
Green/Black  
Green  
REAR  
REAR  
L
Purple/Black  
Purple  
To rear right speaker  
R
Ignition key switch  
Car fuse box  
Ignition wire (Red)  
ACC  
Car fuse box  
(Main fuse)  
Battery wire (Yellow)  
Ground wire (Black) - (To car chassis)  
Battery  
+
|
26  
English  
Connecting Wires to Terminals (KDC-MP5029)  
Rear left output (White)  
Rear right output (Red)  
Front left output (White)  
Front right output (Red)  
FM/AM antenna input  
To connect these leads, refer to  
the relevant instruction manuals.  
To KENWOOD disc changer/External optional accessory  
Fuse (10A)  
Wiring harness  
(Accessory1)  
If no connections are made, do not let the wire come out from the tab.  
When using the optional power amplifier,  
connect to its power control terminal.  
Power control wire (Blue/White)  
P.CONT  
Depending on what antenna you are using,  
connect either to the control terminal of the  
motor antenna, or to the power terminal for the  
booster amplifier of the film-type antenna.  
Motor antenna control wire (Blue)  
TEL mute wire (Brown)  
ANT.  
CONT  
Connect to the terminal that is grounded  
when either the telephone rings or during  
conversation.  
MUTE  
To connect the KENWOOD navigation  
system, consult your navigation manual.  
White/Black  
White  
To front left speaker  
To front right speaker  
To rear left speaker  
FRONT  
L
Gray/Black  
Gray  
FRONT  
R
Green/Black  
Green  
REAR  
REAR  
L
Purple/Black  
Purple  
To rear right speaker  
R
Ignition key switch  
Car fuse box  
Ignition wire (Red)  
ACC  
Car fuse box  
(Main fuse)  
Battery wire (Yellow)  
Ground wire (Black) - (To car chassis)  
Battery  
+
English  
|
27  
Installation  
non-Japanese cars  
Japanese cars  
1 Refer to the section <Removing the hard rubber  
frame> (page 30) and then remove the hard  
rubber frame.  
2 Align the holes in the unit (two locations on each  
side) with the vehicle mounting bracket and  
secure the unit with the accessory screws.  
Metal mounting strap  
(commercially available)  
Firewall or metal support  
T
N
T/N  
T
N
Bend the tabs of the  
T: Toyota cars  
N: Nissan cars  
mounting sleeve with a  
screwdriver or similar utensil  
and attach it in place.  
8 mm  
MAX.  
Self-tapping screw  
(commercially available)  
8mm  
MAX.  
3
4
ø5mm  
ø5mm  
Screw (M4X8)  
(commercially available)  
Accessory3...for Nissan car  
Accessory4 ...for Toyota car  
Make sure that the unit is installed securely in place. If  
the unit is unstable, it may malfunction (for example, the  
sound may skip).  
During installation, do not use any screws except for  
those provided. The use of different screws might result  
in damage to the main unit.  
Damage may occur if a screwdriver or similar tool is used  
with excessive force during the installations.  
|
28  
English  
Screwing the Faceplate on the Unit  
5 Tighten the screw (ø2 × 5 mm) (Accessory 6)  
and bracket (Accessory8) in the hole shown on  
the diagram.  
If you want to fasten the faceplate to the main  
unit so that it does not fall off.  
1 Refer to the section <Removing the hard rubber  
frame> (page 30) and then remove the hard  
rubber frame.  
2 Drop open the faceplate by pressing the Release  
button.  
3 Tighten the stepped screw (Accessory 5) in the  
Accessory8  
hole shown on the diagram.  
Accessory6  
Accessory5  
4 Tighten the screw (ø2 × 5 mm) (Accessory 6)  
and bracket (Accessory7 ) in the hole shown on  
the diagram.  
Never insert the screws in any other screw hole than the  
one specified. If you screw them in another hole, it will  
contact and may cause damage to the mechanical parts  
inside the unit.  
Accessory5  
Accessory7  
..........1  
Accessory6  
Accessory6  
..........2  
English  
|
29  
Removing the Unit  
Removing the hard rubber frame  
Removing the Unit  
1 Engage the catch pins on the removal tool and  
remove the two locks on the upper level.  
Upper the frame and pull it forward as shown in  
the figure.  
1 Refer to the section <Removing the hard rubber  
frame> (page 30) and then remove the hard  
rubber frame.  
2 Remove the screw (M4 × 8) on the back panel.  
3 Insert the two removal tools deeply into the slots  
on each side, as shown.  
Screw (M4X8)  
(commercially available)  
Lock  
Catch  
Accessory2  
Removal tool  
2 When the upper level is removed, remove the  
lower two locations.  
Accessory2  
Removal tool  
4 Lower the removal tool toward the bottom, and  
pull out the unit halfway while pressing towards  
the inside.  
The frame can be removed from the bottom side in the  
same manner.  
Be careful to avoid injury from the catch pins on the  
removal tool.  
5 Pull the unit all the way out with your hands,  
being careful not to drop it.  
|
30  
English  
Troubleshooting Guide  
What might seem to be a malfunction in your unit  
may just be the result of slight misoperation or  
miswiring. Before calling service, first check the  
following table for possible problems.  
? No sound can be heard, or the volume is low.  
The fader or balance settings are set all the way to  
one side.  
Center the fader and balance settings.  
The input/output wires or wiring harness are  
connected incorrectly.  
Reconnect the input/output wires or the  
wiring harness correctly. See the section on  
<Connecting Wires to Terminals>.  
General  
? The power does not turn ON.  
The fuse has blown.  
The values of Volume offset are low.  
After checking for short circuits in the wires,  
replace the fuse with one with the same  
rating.  
Turn up the Volume offset, referring to the  
section on <Audio Setuo> (page 8).  
The <Built-in Amp Setting> (page 21) is OFF.  
Turn it ON.  
The speaker wire has a short-circuit or touches  
the chassis of the vehicle, and then the protection  
function is activated.  
? The sound quality is poor or distorted.  
One of the speaker wires is being pinched by a  
screw in the car.  
Wire or insulate the speaker cable properly  
and press the reset button.  
Check the speaker wiring.  
? There’s a source you can’t switch.  
The speakers are not wired correctly.  
There’s no media inserted.  
Reconnect the speaker wires so that each  
output terminal is connected to a different  
speaker.  
Set the media you want to listen to. If there’s  
no media in this unit, you can’t switch to each  
source.  
? The Touch Sensor Tone doesn’t sound.  
The Disc changer isn’t connected.  
The preout jack is being used.  
Connect the Disc changer. If the Disc changer  
isn’t connected to it’s input terminal, You can’t  
switch to an external disc source.  
The Touch Sensor Tone can’t be output from  
the preout jack.  
The <Touch Sensor Tone> (page 20) is OFF.  
Turn it ON.  
? The memory is erased when the ignition is  
turned OFF.  
? The Dimmer function doesn’t work.  
The Dimmer wire isn’t connected correctly.  
Check the Dimmer wire connection.  
The ignition and battery wire are incorrectly  
connected.  
Connect the wire correctly, referring to the  
section on <Connecting Wires to Terminals>.  
Tuner source  
? The TEL mute function does not work.  
The TEL mute wire is not connected properly.  
? Radio reception is poor.  
Connect the wire correctly, referring to the  
section on <Connecting Wires to Terminals>.  
The car antenna is not extended.  
Pull the antenna out all the way.  
The antenna control wire is not connected.  
? The TEL mute function turns ON even though the  
TEL mute wire is not connected.  
Connect the wire correctly, referring to the  
section on <Connecting Wires to Terminals>.  
The TEL mute wire is touching a metal part of the  
car.  
? The desired frequency can’t be entered with the  
Direct Access Tuning.  
Pull the TEL mute wire away from the metal  
part of the car.  
A station that can’t be received is being entered.  
Enter a station that can be received.  
? Even if Loudness is turned ON, high-pitched tone  
isn’t compensated for.  
You’re trying to enter a frequency with a 0.01 MHz  
unit.  
Tuner source is selected.  
What can be designated in the FM band is to  
0.1 MHz.  
High-pitched tone isn’t compensated for when  
in Tuner source.  
English  
|
31  
Troubleshooting Guide  
Disc source  
Audio file source  
? "AUX" is displayed without achieving External  
? Cannot play an Audio file.  
disc control mode.  
The media is scratched or dirty.  
Unsupported disc changer is connected.  
Clean the media, referring to the CD cleaning  
of the section on <About CDs> (page 5).  
Use the disc changer mentioned in the  
<About CD players/disc changers connected  
to this unit> (page 3) of the section on <Safety  
precautions>.  
? The sound skips when an Audio file is being  
played.  
The media is scratched or dirty.  
? The specified disc does not play, but another one  
plays instead.  
Clean the media, referring to the CD cleaning  
of the section on <About CDs> (page 5).  
The specified CD is quite dirty.  
The recording condition is bad.  
Record the media again or use another media.  
Clean the CD.  
The disc is loaded in a different slot from that  
specified.  
? The Audio file track time isn’t displayed correctly.  
---  
Eject the disc magazine and check the  
number for the specified disc.  
There are times when it isn’t displayed  
correctly according to the Audio file recording  
conditions.  
The disc is severely scratched.  
Try another disc instead.  
? Can’t remove disc.  
The cause is that more than 10 minutes has  
elapsed since the vehicle ACC switch was turned  
OFF.  
The disc can only be removed within 10  
minutes of the ACC switch being turned OFF.  
If more than 10 minutes has elapsed, turn  
the ACC switch ON again and press the Eject  
button.  
? The disc won’t insert.  
There’s already another disc inserted.  
Press the [0] button and remove the disc.  
? Direct Search can’t be done.  
Another function is ON.  
Turn Random Play or other functions OFF.  
? Track Search can’t be done.  
For the discs/folders first or last song.  
For each disc/folder, Track Search can’t be  
done in the backward direction for the first  
song or in the forward direction for the last  
song.  
|
32  
English  
HOLD:  
The protective circuit in the unit activates  
when the temperature inside the  
automatic disc changer exceeds 60°C  
(140°F), stopping all operation.  
Cool down the unit by opening  
the windows or turning on the air  
conditioner. As the temperature falls  
below 60°C (140°F), the disc will start  
playing again.  
The messages shown below display your  
systems condition.  
EJECT:  
No disc magazine has been loaded in  
the changer. The disc magazine is not  
completely loaded.  
Load the disc magazine properly.  
No CD in the unit.  
Insert the CD.  
LOAD:  
Discs are being exchanged in the Disc  
changer.  
NO DISC:  
TOC ERR:  
No disc has been loaded in the disc  
magazine.  
Load a disc into the disc magazine.  
IN (Blink):  
The CD player section is not operating  
properly.  
No disc has been loaded in the disc  
magazine.  
Load a disc into the disc magazine.  
The CD is quite dirty. The CD is upside-  
down. The CD is scratched a lot.  
Clean the CD and load it correctly.  
Reinsert the CD. If the CD cannot be  
ejected or the display continues to flash  
even when the CD has been properly  
reinserted, please switch off the power  
and consult your nearest service center.  
NA FILE:  
An Audio file is played with a format that  
this unit can’t support.  
----  
E-05:  
The CD is upside-down.  
Load the CD correctly.  
BLANK:  
Nothing has been recorded on the MD.  
COPY PRO:  
A copy-protected file is played.  
----  
NO TRACK:  
No tracks are recorded on the MD,  
although it has a title.  
E-15:  
Media was played that doesn’t have data  
recorded that the unit can play.  
Use media that has data recorded that  
the unit can play.  
NO PANEL:  
E-77:  
The faceplate of the slave unit being  
connected to this unit has been removed.  
Replace it.  
The unit is malfunctioning for some reason.  
Press the reset button on the unit. If the  
"E-77" code does not disappear, consult  
your nearest service center.  
E-99:  
Something is wrong with the disc  
magazine. Or the unit is malfunctioning for  
some reason.  
Check the disc magazine. And then  
press the reset button on the unit. If the  
"E-99" code does not disappear, consult  
your nearest service center.  
English  
|
33  
Specifications  
Specifications subject to change without notice.  
AAC decode (KDC-MP6029)  
: AAC-LC ".m4a" files  
FM tuner section  
Frequency range (50 kHz space)  
: 87.5 MHz – 108 MHz  
Frequency range (200 kHz space)  
: 87.9 MHz – 107.9 MHz  
Usable sensitivity (S/N = 30dB)  
: 9.3dBf (0.8 µV /75 Ω)  
Quieting Sensitivity (S/N = 50dB)  
: 15.2dBf (1.6 µV /75 Ω)  
Frequency response ( 3.0 dB)  
: 30 Hz – 15 kHz  
Signal to Noise ratio (MONO)  
: 70 dB  
Selectivity ( 400 kHz)  
: ≥ 80 dB  
Stereo separation (1 kHz)  
: 40 dB  
Audio section  
Maximum output power  
: 50 W x 4  
Full Bandwidth Power (at less than 1% THD)  
: 22 W x 4  
Tone action  
Bass : 100 Hz 10 dB  
Middle : 1 kHz 10 dB  
Treble : 10 kHz 10 dB  
Preout level / Load (during disc play)  
KDC-MP6029: 4000 mV/10 kΩ  
KDC-MP5029: 2000 mV/10 kΩ  
Preout impedance  
: ≤600 Ω  
AM tuner section  
General  
Frequency range (9 kHz space)  
: 531 kHz – 1611 kHz  
Frequency range (10 kHz space)  
: 530 kHz – 1700 kHz  
Usable sensitivity (S/N = 20dB)  
: 28 dBµ (25 µV)  
Operating voltage (11 – 16V allowable)  
: 14.4 V  
Current consumption  
: 10 A  
Installation Size (W x H x D)  
: 182 x 53 x 155 mm  
Weight  
: 1.20 kg (2.64 lbs)  
CD player section  
Laser diode  
: GaAlAs  
Digital filter (D/A)  
: 8 Times Over Sampling  
D/A Converter  
: 1 Bit  
Spindle speed  
KDC-MP6029: 1000 – 400 rpm (CLV 2times)  
KDC-MP5029: 500 – 200 rpm (CLV)  
Wow & Flutter  
: Below Measurable Limit  
Frequency response ( 1 dB)  
: 10 Hz – 20 kHz  
Total harmonic distortion (1 kHz)  
: 0.01 %  
Signal to Noise ratio (1 kHz)  
: 105 dB  
Dynamic range  
: 93 dB  
Channel separation  
: 96 dB  
MP3 decode  
: Compliant with MPEG-1/2 Audio Layer-3  
WMA decode  
: Compliant with Windows Media Audio  
|
34  
English  

Motorola i885 User Manual
Melissa Exido 245 076 User Manual
KitchenAid KGSS907S User Manual
IBM iSeries 270 and 820 SENG 3002 01 User Manual
Hamilton Beach 42491 User Manual
Blaupunkt Sydney RCM 126 User Manual
Black &amp; Decker SDC740B User Manual
AT&amp;T VU CU920 User Manual
APC SRT3000 User Manual
AMCC 3WARE 9500S User Manual