Kenwood KDC 7080RV User Manual

CD-RECEIVER

KDC-7080R

KDC-7080RV

INSTRUCTION MANUAL

COMPACT

DIGITAL AUDIO

Safety precautions

IMPORTANT INFORMATION

2WARNING

2CAUTION

You cannot connect the unit directly to the

following CD automatic changers. For users

who want to use older changers with the

unit, follow the directions below according to

the type of changer you own:

To prevent injury and/or fire, take the

following precautions:

• Insert the unit all the way until it is fully

locked in place. Otherwise it may fly out of

place during collisions and other jolts.

To prevent damage to the machine,

take the following precautions:

• Make sure to ground the unit to a negative

12V DC power supply.

• KDC-C200 / KDC-C300 / KDC-C400

• Do not open the top or bottom covers of the

unit.

• Do not install the unit in a spot exposed to

direct sunlight or excessive heat or humidity.

Also avoid places with too much dust or the

possibility of water splashing.

• Do not subject the faceplate to excessive

shock, as it is a piece of precision

equipment.

• When replacing a fuse, only use a new one

with the prescribed rating. Using a fuse with

the wrong rating may cause your unit to

malfunction.

• To prevent short circuits when replacing a

fuse, first disconnect the wiring harness.

• Do not place any object between the

faceplate and the unit.

• During installation, do not use any screws

except for the ones provided. The use of

improper screws might result in damage to

the main unit.

• Do not apply excessive force to the moving

faceplate. Doing so will cause damage or

malfunction.

Use the extension cable and the control box

attached to the CD changer, and the optional

CA-DS100 converter cable.

• KDC-C301 / KDC-C600 / KDC-C800 / KDC-

C601 / KDC-C401

Use the extension cable attached to the CD

changer, and the optional CA-DS100

converter cable.

• KDC-C100 / KDC-C302 / C205 / C705 /

non-Kenwood CD changers

• When extending the ignition, battery or

ground cables, make sure to use automotive-

grade cables or other cables with an area of

0.75mm (AWG18) or more to prevent cable

deterioration and damage to the cable

coating.

• To prevent short circuits, never put or leave

any metallic objects (e.g., coins or metal

tools) inside the unit.

• If the unit starts to emit smoke or strange

smells, turn off the power immediately and

consult your Kenwood dealer.

• Make sure not to get your fingers caught

between the faceplate and the unit.

• Be careful not to drop the unit or subject it to

strong shock.

The unit may break or crack because it

contains glass parts.

• Do not touch the liquid crystal fluid if the

LCD is damaged or broken due to shock. The

liquid crystal fluid may be dangerous to your

health or even fatal.

If the liquid crystal fluid from the LCD

contacts your body or clothing, wash it off

with soap immediately.

Cannot be used with this model.

2CAUTION

You can damage both your unit and

the CD changer if you connect them

incorrectly.

2CAUTION

Do Not Load 8-cm (3-in.) CDs in the

CD slot

If you try to load an 8-cm CD with its adapter

into the unit, the adapter might separate

from the CD and damage the unit.

• Do not apply excessive force to the open

faceplate or place objects on it. Doing so will

cause damage or breakdown.

— 3 —

Safety precautions

• The illustrations of the display and the panel

appearing in this manual are examples used

to explain more clearly how the controls are

used. Therefore, what appears on the display

in the illustrations may differ from what

appears on the display on the actual

equipment, and some of the illustrations on

the display may represent something

impossible in actual operation.

• The functions that can be used and the

information that can be displayed will differ

depending on the external disc players being

connected.

Mask key

NOTE

If you have transmitted the Mask Key's

signal once to the unit in advance, you will

have to transmit it once again if the unit has

been removed from the battery. This

function helps prevent theft.

When using the unit for the first time:

In order to deactivate the demonstration

mode, be sure to press the transmit button

to transmit the Mask Key's signal.

If this procedure is not carried out, the

control panel of the unit will re-open in two

seconds even with your vehicle's ignition

turned off.

• If you experience problems during

installation, consult your Kenwood dealer.

Egnlish

• If the unit fails to operate properly, press the

RESET button. When the faceplate controls

are not visible, press the left part at the

upper side of the faceplate (as illustrated on

p.13) for as many times as you have preset

to make the faceplate controls appear. The

unit returns to factory settings when the

RESET button is pressed. After you press

the reset button, the Mask Key will be

needed to restart the unit. If the unit still fails

to operate properly after the RESET button

has been pressed, contact your local

2CAUTION

Do not loose the "Mask Key".

If power is disconnected from the unit,

correct operation can only be restored by the

"Mask Key's" signal.

The "Mask Key" will also be required for

service repair.

KENWOOD dealer for assistance.

• Press the reset button if the CD auto

changer is first controlled and operates

incorrectly. The original operating condition

will return.

EJECT

NOTE

If you send products in for repair that include

a mask key, make sure to present the unit

together with the mask key.

DISP

Reset button

• Characters in the LCD may become difficult

to read in temperatures below 41 ˚F (5 ˚C).

— 4 —

Cleaning the Faceplate Terminals

If the terminals on the unit or faceplate get

dirty, wipe them with a dry, soft cloth.

The marking of products using lasers

(Except for some areas)

CLASS 1

LASER PRODUCT

Cleaning the Unit

If the front panel gets dirty, turn off the

power and wipe the panel with a dry silicon

cloth or soft cloth.

The label is attached to the chassis/case and

says that the component uses laser beams

that have been classified as Class 1. It

means that the unit is utilizing laser beams

that are of a weaker class. There is no

danger of hazardous radiation outside the

unit.

2CAUTION

Do not wipe the panel with a stiff cloth or a

cloth dampened by volatile solvents such as

paint thinner and alcohol. They can scratch

the surface of the panel and/or cause the

indicator letters to peel off.

Lens Fogging

Cleaning the CD Slot

Right after you turn on the car heater in cold

weather, dew or condensation may form on

the lens in the CD player of the unit. Called

lens fogging, CDs may be impossible to play.

In such a situation, remove the disc and wait

for the condensation to evaporate. If the unit

still does not operate normally after a whilst,

consult your Kenwood dealer.

As dust can accumulate in the CD slot, clean

it occasionally. Your CDs can get scratched if

you put them in a dusty CD slot.

— 5 —

Handling Compact discs

Playing a CD that is dirty, scratched

or warped can cause the sound to

skip and the unit to operate

incorrectly, resulting in worsened

sound quality. Take the following

precautions to prevent your CDs from

getting scratched or damaged.

Cleaning CDs

Do Not Load CD Accessories in Slot

If a CD has become dirty, wipe it off gently

using a commercially available cleaning cloth

or a soft cotton cloth, starting from the

centre of the disc and moving outward. Do

not clean CDs with conventional record

cleaners, anti- static formulas, or chemicals

such as paint thinner or benzene.

Do not use commercially available CD

accessories that can be loaded into the CD

slot, such as stabilisers, protective sheets,

or CD cleaning discs, since they can cause

the unit to malfunction.

Egnlish

Removing the CD

Only remove the CD from the machine in a

horizontal direction. You may damage the

surface of the CD if you try pulling it down

as it ejects.

Handling CDs

• Do not touch the recorded side of the CD

(i.e., the side opposite the label) when

holding it.

Checking New CDs for Burrs

When playing a new CD for the first time,

check that there are not any burrs stuck to

the perimeter of the disc or in the central

hole. CDs with burrs stuck on them may not

load properly or may skip whilst playing.

Remove burrs using a ballpoint pen or a

similar utensil.

Do Not Use Special Shape CDs

• Be sure to use round shape CDs only for

this unit and do not use any special shape

CDs. Use of special shape CDs may cause

the unit to malfunction.

• Do not stick tape on either side of the CD.

Tape

Burrs

Storing CDs

COMPACT

• Do not store CDs in areas exposed to direct

sunlight – such as a car seat or above the

fascia panel (dashboard) – or other hot

places.

• Remove CDs from the unit when not

listening to them for a whilst, and put them

back in their cases. Do not stack CDs that

have been removed from their cases or prop

them against something.

DIGITAL AUDIO

• Be sure to use CDs with disc mark

Burrs

only for this unit.

Do Not Use CDs with Sticker on the

Labelled Side

Do not use the CD with the label sticker

stuck on it.

Using such a CD may cause the CD to be

deformed and the sticker to peel off,

resulting in malfunction of the unit.

— 6 —

General features

Power

SRC

You can help prevent theft of the unit by reversing the

faceplate so that the control panel cannot be seen, hiding the

unit, and shutting off the audio.

EJECT

Power ON/OFF:

When you turn your vehicle’s ignition on, the unit’s power will

also turn on, with the faceplate reversing to show the control

panel.

DISP

When you turn your vehicle's ignition off, the faceplate will

reverse to hide the control panel after a period of time which

you have set in the "Time setting for removing the faceplate" in

the menu. The unit's power will turn off.

Alternatively, you can remove the faceplate during that period.

For details, refer to the "Removing the faceplate" (page12).

AUD

AM/NF CLK

ATT / LOUD

#1 - 6

NOTE

• After installation of your Mask unit, be sure to transmit the

"Mask Key's" signal to deactivate the demonstration mode.

If this procedure is not carried out, the control panel of the unit

will re-open in two seconds even with your vehicle's ignition

turned off.

£ indicator

ATT indicator

• When the control panel of the faceplate is hidden, the unit will

be locked by the sleeve, making it more difficult to remove the

unit.

• When the moving faceplate is hit by an object, it will stop and

return to its original state. Remove the object and repeat the

action.

2CAUTION

Using the Unit in Vehicles with Covered Consoles

• Make sure the console is uncovered whilst the faceplate is

reversed.

LOUD indicator

• Do not exert any excess force on the movable parts of the unit,

including the faceplate, as it can cause failure in the unit’s

mechanism.

— 7 —

General features

Switching Modes

Volume

Switching Modes:

Increasing Volume:

Each time you press the SRC button, the mode switches as

follows:

Press the u button to turn up the volume.

Egnlish

Decreasing Volume:

▼

Press the d button to turn down the volume.

Tuner mode

▼

CD mode

▼

External disc control mode 1

Attenuator

▼

This function allows you to turn down the volume quickly.

External disc control mode 2/AUX mode

▼

Turning Attenuator On/Off:

Standby mode

Press the ATT button to switch the attenuator on and off.

When the attenuator is on, the ATT indicator blinks.

When the attenuator is off, the volume returns to the original

level.

Selecting the standby mode:

Press the SRC button repeatedly to select to "ALL OFF" .

When "ALL OFF" is displayed, the standby mode is turned on.

The standby mode turns all functions off although leaving the

unit’s power on. Use this mode when you want to have the

display illuminated but do not want to listen to anything.

NOTE

Turning the volume up, or turning it all the way down deactivates

the attenuator function.

NOTE

• The mode switches to the next mode from any mode which

cannot be used.

Loudness

• The external disc control mode will differ depending on the unit

that is connected.

This function amplifies low and high tones when the volume is

• The AUX mode is available only when the changer / AUX

switching adapter (KCA-S210A or CA-C1AX) or CD changer

(KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is

connected to this unit.

During the AUX mode, "AUX" / AUX-name will show in the

display. When the CA-C1AX is being used, the AUX Mode will

replace the External Disc Control Mode.

turned down.

The LOUD indicator lights up, when the loudness function is

on.

Turning Loudness On/Off:

Hold down the LOUD button for one second or more to switch

the loudness on and off.

NOTE

Presetting AUX-name

(Only when the KCA-S210A is connected)

In the AUX mode, press the NAME.S button for two seconds or

more. "NAME SET" is display and AUX-name mode is entered.

Input the characters, referring to the section on "Presetting Disc

Names (DNPS)" (page24).

Audio Control Setting

Adjust various parameters of sound quality.

— 8 —

Press the AUD button to enter the control mode.

"Bass F" : Adjust the centre frequency of the bass.

Setting values: 60 / 70 / 80 / 100 (Only when the bass quality

factor is set to 1.00, 1.25 or 1.50) / 150 (Only when the bass

quality factor is set to 2.00) Hz

Selecting mode

Press either the FM or AM button.

Each time the button is pressed, the adjustment mode will

change.

NOTE

Please refer to the following for the contents of the

adjustment modes.

This mode is available only when the Sound coordinate system is

on. (page31)

NOTE

Source tone memory

Each source (CD, FM, AM, and disc changer) has its own

memory in which to store the bass and treble tone settings.

The settings made for a particular source are then recalled

automatically whenever you use that source (e.g., FM mode uses

the tone settings made for FM, AM for AM, etc.).

"Bass" : Adjust the bass level.

Setting values: - 8 – + 8

Adjust each mode

Press the 4/¢ button.

Please refer to the following for the adjusting values.

Press the AUD button to end the control mode.

"Bass Q" : Adjust the Bass quality factor.

Setting values: 1.00 / 1.25 / 1.50 / 2.00

NOTE

This mode is available only when the Sound coordinate system is

on. (pagee31)

"Kex"/"EC"/"dB" : Recalling the kenwood preset sound setting

Press the preset buttons (#1-6).

Settings: #1;Flat, #2;Rock, #3;Pops/Top40, #4;Jazz, #5;Easy,

#6;Scan of #1-5

NOTE

"Bass EXT" : Switch the Bass Extend mode on/off.

Setting values: ON / OFF

• This mode is available only when the Sound coordinate system

is on. (page31)

• You can call the following settings with this function; bass

centre frequency, bass level, bass quality factor, bass

extension, treble centre frequency, and treble level setting.

Their setting values are different depending on the setting of

the mobile preset plan mode.

(When the bass extend mode is set to on, low

frequency response is extended by 20%.)

NOTE

This mode is available only when the Sound coordinate system is

on. (page31)

— 9 —

General features

quality factor, bass extension, treble center frequency, and

treble level adjust mode.

NOTE

"TreF" : Adjust the centre frequency of the treble.

Setting values: 10.0 / 12.5 / 15.0 / 17.5 kHz

NOTE

• This setting can be made only when the Sound coordinate

system is on. (page31)

• The settings you can preset are, bass centre frequency, bass

level, bass quality factor, bass extension, treble centre

frequency, and treble level.

Egnlish

This mode is available only when the Sound coordinate system is

on. ( page31).

"Treble" : Adjust the treble level.

Setting values: - 8 – + 8

Recalling your sound settings:

Press a preset button (#1-6) except during the bass center

frequency, bass level, bass quality factor, bass extension,

treble center frequency, and treble level adjust mode.

"Balance" : Adjust the balance level.

NOTE

Setting values: Left 15 – Right 15

This mode is available only when Sound coordinate system is on.

Mobile Preset

This function allows you to adjust the setting that is recalled

with the sound coordinate system, according to types of

speakers.

"Fader" : Adjust the fader level.

Setting values: Front 15 – Rear 15

Press the SRC button repeatedly to select the standby mode.

"ALL OFF" is displayed when the standby mode is selected.

"V OFFSET" : Set the sound level of the each source selected by

adjusting the level difference between the basic

sound level and the required level.

Press the AUD button to enter the mobile preset plan mode.

Press either the 4 or ¢ button to select the type of

speaker. The setting switches as follows.

Off / For the OEM speaker / For 6/6x9 in. speaker /

For 5/4 in. speaker

Setting values: - 8 –

Press the AUD button to end the mobile preset plan mode.

Storing your sound settings:

NOTE

Hold down a preset button (#1-6) for two seconds or more

except during the bass center frequency, bass level, bass

• This mode is available only when the Sound coordinate system

is on. (page31)

— 10 —

• When you change the setting of type of speaker, the bass and

treble tone settings are returned to original levels.

"CALL" disappears from the display, and the volume of the

original source is restored gradually.

Turning TEL Mute Function Off After Phone Call:

Hang the phone up.

"CALL" disappears from the display.

The original source (i.e., the one used before the phone call) is

returned to automatically, and the volume restored gradually.

Switching Display

You can change the display in each mode.

Changing the Display:

Each time you press the CLK button, the display switches as

follows:

Faceplate Angle Adjustment

You can adjust the faceplate angle for easy viewing.

Mode display

Clock

Adjusting faceplate angle:

Press the ¡ (EJECT) button to make the faceplate slide open,

and then adjust the faceplate angle using the angle adjustment

switch.

Date

Adjustment may be made from 0 to 2.

NOTE

The £ indicator lights whilst the clock is displayed.

0 1 2

TEL Mute

Shut down the audio system temporarily whenever an

incoming call is received.

NOTE

• Firmly slide the switch until it clicks.

NOTE

• Do not apply excessive force to the faceplate under settings 1

The function will not work if a cable is not connected to the car

phone.

or 2.

• Set the angle adjustment switch to "0" before removing the

faceplate.

When the telephone rings:

When a call is received, "CALL" is displayed and all the unit

functions are temporarily interrupted.

Restoring Original Unit Source During Phone Call:

Press the SRC button.

— 11 —

General features

• When removing the faceplate, pull it out only when it is fully

open. The detachment of the faceplate whilst it is moving might

result in damage to the unit.

• Do not apply excessive force to the faceplate bracket without

attaching the faceplate. Doing so will cause the faceplate

bracket to be deformed.

• Do not touch the connector on the faceplate bracket after

removing the faceplate. Touching the connector may cause

damage to the unit.

• Do not touch two metal parts on both sides of the faceplate

bracket. Touching those parts may injure you.

Removing the Faceplate

The faceplate can be detached from the unit, helping to deter

theft.

Egnlish

Removing the faceplate:

Choose the way from among the following and open the

faceplate.

Turn the ignition off, hold down the SRC button for one second

or more, or press the left part at the upper side of the

faceplate (as illustrated on p.13) for as many times as you have

preset in the "Manual Open Button Setting" (OPEN SW #) in

the menu when the control panel has been hidden.

NOTE

• Sliding the faceplate lock switch cause the unit’s power to turn

off. If you want to operate the unit again, remove the faceplate

from the faceplate bracket completely and then reattach it.

• The faceplate is a precision piece of equipment and can be

damaged by shocks or jolts. For that reason, keep the faceplate

in its special storage case whilst detached.

• Do not expose the faceplate or its storage case to direct

sunlight or excessive heat or humidity. Also avoid places with

too much dust or the possibility of water splashing.

Set the faceplate's angle adjustment switch to "0" to set the

faceplate angle to the vertical.

For details, refer to "Faceplate Angle Adjustment" (page 11).

NOTE

If the faceplate's angle adjustment switch is not set to "0" when

mounting the faceplate on the faceplate bracket, it may be

difficult to mount the faceplate or the faceplate may not be

securely attached and could fall off.

Set the angle adjustment switch to "0" before removing the

faceplate.

Reattaching the Faceplate:

Hold the faceplate so that the control panel faces the front

toward you and set the left side of the faceplate in the

faceplate bracket.

Slide the faceplate lock switch to the left during the period

which you have set in the "Time setting for removing the

faceplate" in the menu.

2CAUTION

Do not set the right side of the faceplate in the faceplate bracket

first, when reattaching the faceplate. Doing so may cause the

connector on the faceplate bracket to malfunction.

Press the right side of the faceplate until it locks.

Faceplate lock switch

Holding the centre part of the faceplate, pull it out.

The faceplate bracket will automatically close.

NOTE

2CAUTION

If the faceplate bracket's angle was not set to the vertical when

— 12 —

the faceplate was mounted, check that the faceplate is securely

attached to the faceplate bracket by holding its right side and

pulling it gently towards you.

NOTE

When you set the Manual Open Button setting to 2 or 3, press

the upper left part of the faceplate without pausing. If you do not

press that part without pausing, the command cannot be verified

correctly.

Forced Closing

This function prevents tampering with the unit your car is

being serviced etc.

Hiding the unit with the ignition turned on (forced closing):

Hold down the SRC button for one second or more.

The faceplate will slide open. When the period of time which

you have set in the "Time setting for removing the faceplate" in

the menu has passed, the faceplate automatically reverses to

hide the control panel. However, you can remove the faceplate

during that period. For details, refer to the "Removing the

faceplate" (page12).

NOTE

• When the closing faceplate is hit by an object, the unit will turn

off without the faceplate closing all the way. Remove the object

and press the SRC button to turn the unit back on, then turn it

off again to make it close properly.

• Whilst the control panel is moving, pressing the buttons will not

have any effect. Do not try to press the buttons on the control

panel as the faceplate is moving, as excessive force may

damage the unit.

• During the forced closing of the unit (i.e., having the unit left

closed whilst ignition is turned on), the faceplate will not open

no matter how often the ignition is turned on or off, unless

"Manual Open button" at the rear of the faceplate is pressed in

order to open it. You can prevent tampering of the unit when

letting someone else drive your car by keeping it closed this

way.

To cancel the forced closing of unit and open control panel:

Press the left part at the upper side of the faceplate for as

many times as you have preset in the "Manual Open Button

Setting" (OPEN SW #) in the menu. The faceplate will open and

show the control panel.

— 13 —

Tuner features

Tuning

SRC

Press the SRC button repeatedly until the tuner mode is

obtained. "TUNER" is displayed only when the tuner mode is

selected.

Egnlish

EJECT

Press either the FM or AM button to select the band.

Each time you press the FM button, the band switches

between the FM1, FM2 and FM3.

DISP

Press the AM button to select the MW and LW bands.

• Auto Seek Tuning

#1 - 6

TI/VOL ADJ DISP/NAME.S

Press the ¢ button to seek increasing frequencies.

Press the 4 button to seek decreasing frequencies.

• Preset station seek tuning

Press the ¢ button to move to the next preset station (i.e.,

the one with the next highest number), and the 4 button to

move to the last preset station (i.e., the one with the next

lowest number).

Frequency

Band display

NOTE

If the frequencies stored at the preset numbers receive

stations which were not originally memorized when traveling

long distances, the preset number is not displayed. In such

cases, pressing the 4/¢ button to use preset station

seek will receive channel 1.

• Manual Tuning

ST indicator

Preset station number

AUTO indicator

Press the ¢ button to increase the frequency by one step.

Press the 4 button to decrease the frequency by one step.

NOTE

• The ST indicator lights up when stereo broadcasts are being

received.

• Please see the menu settings about selecting tuning mode.

(page31)

Station Preset Memory

Store the frequency of the station currently being listened to.

You can then recall that station with a single touch of a button.

— 14 —

Select the band/ station that you want to have stored.

Once the name is displayed for the station you want to

listen to

Hold down the button (#1-6) that you want to use for the

station, for two seconds or more.

The button number blinks once in the display to indicate that

the data has been stored.

Press the OK button.

Reception starts of the displayed station, and the seek mode

ends.

Cancelling mode during input:

Press the DNPP button.

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

The seek mode is cancelled.

NOTE

You can store 6 stations in each of the FM1, FM2, FM3, and AM

(MW and LW) bands.

Preset station seek with Programme service

name

(Function of Remote Control)

You can search for the preset station with Programme Service

name.

Press the DNPP button on the remote control.

"SNPP" will be displayed once the seek mode is entered.

The names of the stations preset in the band currently listened

to are displayed for 5 seconds each.

The display band switches in the following order:

= FM1 Ô FM2 Ô FM3 Ô AM +

Each time you press the ¢ button, the station display

switches in the forward direction.

Each time you press the 4 button, the station display

switches in the reverse direction.

Stations which have no names will be displayed as

frequencies.

NOTE

Changing the Displayed Band

Pressing the FM button switches between the FM1, FM2, FM3

and AM displays, in that order.

Pressing the AM button switches between the displays in the

reverse direction.

— 15 —

Tuner features

RDS features

Switching Display for Tuner

You can change the display used when listening to the radio.

38(PTY)

Switching the Display:

Egnlish

EJECT

Pressing the DISP button switches the display as follows.

Select the Radio Text Display mode.

DISP

Programme Service name (during RDS station reception)/Station frequency

Radio text

#1 - 6

TI/VOL ADJ DISP/NAME.S

Displaying Frequencies:

Hold down the DISP button for one second or more.

The frequency for the RDS station will be displayed for five

seconds instead of the station name.

NOTE

If the RDS station currently tuned to is transmitting no text whilst

the Radio Text Display mode is turned on, "NO TEXT" will appear

in the display. Whilst awaiting reception, "WAITING" will be

displayed.

PTY indicator TI indicator

2WARNING

To prevent accidents, drivers should not look at the display whilst

on the road.

— 16 —

RDS (Radio Data System)

Traffic Information Function

You can listen to traffic information. If you are listening to

tapes or discs, they will continue playing until a traffic bulletin

is broadcast.

RDS is a digital information system that lets you receive

signals besides those of regular radio programmes, such as

network information being transmitted from radio stations.

When listening to an RDS station (ie, a station with RDS

capability), the programme service name of the station is

displayed along with the frequency, advising you quickly which

station is being received.

RDS (Radio Data System) stations also transmit frequency data

for the same station. When you are making long trips, this

function automatically switches to the particular frequency

with the best reception for the particular network of stations

that you want to listen to. The data is automatically stored,

allowing you to switch quickly to another RDS stations,

broadcasting the same programme, that has better reception.

These include stations stored in the station preset memory that

you often listen to.

Turning TI function On/Off:

Press the TI button to turn the function on and off.

When the function is on, the TI indicator is turned on.

When none is being received, the TI indicator will blink on and

off. When a traffic information station is being received, the TI

indicator will turn on.

When a traffic bulletin begins to be broadcast, "TRAFFIC" will

be displayed, and reception will begin at the preset volume.

If you are listening to a tape or disc when a traffic bulletin

begins, they will automatically be turned off. When the bulletin

ends or poor reception is experienced, the tape or disc will

begin playing again.

NOTE

Pressing the TI button whilst in the MW/LW band automatically

switches reception to the FM band. However, the MW/LW band

is not returned to when the TI button is pressed again.

Enhanced Other Network

Stations that offer <Enhanced Other Network> also transmit

information about other RDS stations that have traffic

information. When you are tuned to a station that is not

transmitting traffic information, but another RDS station starts

transmitting a traffic bulletin, the tuner automatically switches

to the other station for the duration of the bulletin.

Switching to a Different Traffic Information Station:

Use the 4 / ¢ buttons to make an auto seek of the TI

stations in a certain band.

NOTE

• When you are listening to a tape or disc, you cannot change to

another TI station.

• When the auto TP seek function is turned on and reception

starts to weaken, the tuner automatically seeks traffic

information stations with better reception.

• If you are tuned to a station that is not a traffic information

station itself but which provides <Enhanced Other Network>

services, you can still have traffic information received.

• Holding the TI button down for one second or more when the

TI function is on in the disc control mode results in a change to

the frequency display of the traffic information station for five

seconds.

Alarm

When an emergency transmission (announcing disasters, etc.)

is sent, all current functions are interrupted to allow the

warning to be received.

— 17 —

RDS features

17. Finance

(Finance)

Programme Type (PTY) Function

Conduct auto seek tuning only on those stations with selected

kinds of programmes.

18. Children’s programmes (Children)

19. Social Affairs

20. Religion

(Social A)

(Religion)

(Phone In)

(Travel)

(Leisure)

(Jazz)

(Country)

(Nation M)

(Oldies)

(Folk M)

(Document)

Egnlish

21. Phone In

Press the 38(PTY) button.

22. Travel

"PTY" is displayed, and the Programme Type Selection (PTY)

Mode entered.

23. Leisure

24. Jazz Music

25. Country Music

26. National Music

27. Oldies Music

28. Folk Music

29. Documentary

If you make no key input in 30 seconds, the mode will

automatically turn off.

NOTE

You cannot use this function whilst the traffic bulletin is received.

NOTE

Changing the Display Language to French, German, or Swedish

(Speech.....1~9,16~23, 29, Music.....10~15, 24~28)

• You can select the type of programme directly by pressing a

preset button. The buttons are factory-set to the following

type of programmes:

In the PTY mode, press the DISP button to display the name of

the language currently used.

If you want to change the language, press the preset button for

the desired language and then the DISP button.

1. Music

4. Other Music

2. Speech

5. Serious Classical

3. News

6. Varied

English is #1, French is #2, German is #3, and Swedish is #4.

Select the type of programme to be received

• Press either the FM or AM buttons repeatedly until the type

of programme you want to listen to.

NOTE

Changing the Preset Button Settings for Programme Type

After selecting the type of programme to be stored in a certain

preset button, hold down that button for two seconds or more.

The previously stored data for that button are erased and the

new programme type is stored.

The selection includes:

Speech

(Speech)

(Music)

Music

Seeking the selected programme type

1. News

(News)

Press the 4 or ¢ button to make a seek of frequencies

2. Current Affairs

3. Information

4. Sports

(Affairs)

(Info)

(Sport)

(Educate)

(Drama)

(Culture)

(Science)

(Varied)

with your selected type of programme.

The display blinks and the seek starts.

"PTY" blinks in the display for about 30 seconds.

If you make no key input in 30 seconds, the PTY selection

mode will turn off automatically.

5. Education

6. Drama

7. Culture

8. Science

NOTE

9. Varied

If no programme can be found, "NO PTY" is displayed.

If you want to select another type of programme, repeat steps 2

and 3 above.

10. Pop Music

11. Rock Music

12. Easy Listening Music

13. Light Classical

14. Serious Classical

15. Other Music

16. Weather

(Pop M)

(Rock M)

(Easy M)

(Light M)

(Classics)

(Other M)

(Weather)

Switching to Other Stations with the Same Type of Programme:

When "PTY" is blinking in the display, perform auto seek tuning.

The tuner scans for another station with the same type of

programme.

— 18 —

Cancelling Programme Type Function During Its Operation:

Holding down the DISP button for one second or more results

in one scrolling display of the text.

Press the 38(PTY) button.

To scroll automatically:

Press the DISP button to display the Radio Text.

The text will be displayed in one scrolling display.

Holding down the DISP button for one second or more results

in one scrolling display of the text.

NOTE

Please see the menu settings (page34) about switching between

manual scrolling and automatic scrolling.

Presetting Volume for Traffic Information/News

Preset the volume level to be used for traffic information and

news broadcasts.

Tune into the station for which you want to set the volume.

Adjust the volume to the desired level.

Hold down the TI VOL ADJ button for two seconds or more.

The volume level blinks once in the display to indicate that the

data has been stored.

Future traffic information/news broadcasts are heard at the

preset level.

NOTE

• The volume cannot be lowered by this function during tuner

reception. The volume is only set when it is louder than the

listening volume of the tuner.

• You can arrange only to listen to traffic information or news

bulletins with at preset volume with the volume set at

minimum.

Radio Text Scroll

This function permits the text to be scrolled and the entire text

to be displayed. The scrolling method differs depending on the

setting of scrolling in the menu.

To scroll manually:

Press the DISP button to display the Radio Text.

— 19 —

CD/External disc control features

■ When a unit equipped with an O-N switch is to be

connected, please also see the instruction manual of this

unit.

DISC+

SRC

Set the O-N switch to "N". "N"-operation will be set.

Egnlish

"N"-operation:

EJECT

• The disc title and track title of the CD text can be displayed.

• The disc name will be displayed when the name has been

registered to any connected unit with the Presetting Disc

Names function, or when the playing unit contains a disc to

which the disc title has been recorded.

DISP

"O"-operation:

DISP/NAME.S DISC–

RDM

D.SCN

• CD text cannot be displayed.

SCAN

REP

M.RDM

• Regardless of the control unit, the characters that can be

registered with the Presetting Disc Names function are "A~Z

0~9 /, +, –, ∗, =, <, >, [ , ]".

• The disc name will be displayed when the name has been

registered to the playing unit with the Presetting Disc Names

function.

NOTE

Track number

IN indicator

Disc number

Track time

The CD text, Presetting Disc Names, and Disc Name Preset Play

functions may not be operational depending on the unit.

Playing CDs

Playing CDs:

Press the ¡(EJECT) button to slide open the faceplate,

showing the CD (insertion) slot. Holding the CD with the

labeled side facing up, insert it in the slot.

The faceplate will close, and the CD will start playing.

The ¢ indicator will light when a CD has been inserted.

Playing CDs Already Inserted:

Press the SRC button repeatedly until the CD mode is

obtained. "CD" is displayed when the CD mode has been

selected.

— 20 —

The CD will start playing.

The disc will start playing.

NOTE

Pausing and Restarting CD Play:

Press the 38 button to make the disc pause.

The external disc control mode will differ, depending on the unit

that is connected.

Mode Display Examples

• "CD2" ...when a CD player is connected

• "DISC" ...when a disc changer is connected

• "DISC-1" , "DISC-2" ...when two disc changers are connected

Press the same button again to start play again.

Eject:

Press the ¡(EJECT) button. The faceplate will slide to eject

the CD.

Press the ¡(EJECT) button to close the faceplate.

Pausing and Restarting Disc Play:

2CAUTION

Press the 38 button to make the disc pause.

• Do not attempt to insert a CD into the slot if another one is

already there.

• The unit can only play 12-cm (5-inch) CDs. If you insert an 8-cm

(3-inch) CD, it will get stuck inside and can cause the unit to

malfunction.

• When the faceplate has been slid open, it might interfere with

the gear lever or something else. If this happens, pay attention

to safety and move the gear lever or take an appropriate action,

then operate the unit.

Press the same button again to start play again.

NOTE

• When one disc has finished playing its last track, the next disc

in the changer starts playing. When the last disc in the changer

has finished, the player returns to the first disc and starts

playing it.

• Disc #10 is displayed as "0".

NOTE

• The sound will be temporarily muted whilst the faceplate is

moving.

• The only buttons that will work during the eject state are the

¡(EJECT), SRC, TI, and ATT buttons, as well as the volume

control button.

• When you load a CD and eject it right away, the next time you

try to insert the CD may not load. In such a situation, take the

CD out for a moment and then reinsert it.

Fast Forwarding and Reversing Disc Play

Fast Forwarding Disc Play:

Hold down on the ¢ button.

Release your finger to play the disc at that point.

Reversing Disc Play:

Hold down on the 4 button.

Release your finger to play the disc at the point.

NOTE

You cannot use reverse play between tracks depending on the

model being connected. Instead, the reverse play function is

cancelled when it reaches the beginning of a track, at which

point normal play automatically resumes.

Playing Other Disc mode

This function permits the connection of optional players and

the playing of discs other than the loaded CD (in the current

unit).

Playing Discs:

Press the SRC button repeatedly to select the external disc

control mode.

— 21 —

CD/External disc control features

Play starts at the beginning of the displayed disc.

NOTE

Track Search

Search forwards or backwards through the tracks on the disc

until you reach the one that you want to listen to.

"LOAD" is displayed when discs are being exchanged on the disc

changer.

Egnlish

Making a Reverse Track Search:

Press the 4 button to display the desired track number.

Press once to search back to the beginning of the current

track, twice to search back to the beginning of the previous

track, and so forth.

Track / Disc Repeat

Repeat playing the current track or disc.

Play starts at the beginning of the displayed track number.

NOTE

(For disc changers)

Turning Repeat Play Function On/Off:

Press the REP button to switch the repeat play function on and

off as follows :

Pressing the 4 button whilst listening to track 1 only searches

back to the beginning of that track. The reverse search is not

"recycled" to the last track on the disc.

▼

Making a Forward Track Search:

Track Repeat ON

Press the ¢ button to display the desired track number.

Press once to fast forward to the next track, twice to fast

forward to the track after that, and so forth.

▼

Disc Repeat ON (Function of disc changers)

▼

Play starts at the beginning of the displayed track number.

Track/Disc Repeat OFF

NOTE

(For disc changers)

"T-Repeat/Repeat ON" is displayed and the track number blinks

in the display when track repeat is on.

"D-Repeat ON" is displayed and the disc number blinks in the

display when disc repeat is on.

You cannot make a forward track search when listening to the

last track on a disc.

NOTE

Repeat play is cancelled when you eject the disc.

Disc Search

(Function of disc changers)

Search forwards or backwards through the discs in a disc

changer until you reach the one that you want to listen to.

Making a Reverse Disc Search:

Track Scan

Press the DISC– button to display the desired disc number.

Each time the button is pressed, the displayed disc number

decreases by one.

Successively play the beginning of each track on a disc until

you find the track that you want to listen to.

Play starts at the beginning of the displayed disc.

Starting the Track Scan:

Making a Forward Disc Search:

Press the SCAN button. "T-Scan/Scan ON" is displayed and the

first 10 seconds of each track are played, and the tracks are

played in order.

Press the DISC+ button to display the desired disc number.

Each time the button is pressed, the displayed disc number

increases by one.

The track number currently being heard blinks in the display.

— 22 —

Stopping to Listen to the Track Being Scanned:

Press the 38 or SCAN button again to stop the scan and keep

on listening to a track normally.

Switching Display for Discs

Switch the display that appears whilst discs are playing.

NOTE

Switching Display for Discs:

Each time you press the DISP button, the display during disc

play switches as follows.

• The track scan function is cancelled when you eject the disc.

• The track scan function only scans each track on a disc once.

Track time

Disc name (DNPS)

Disc Scan

(Function of disc changers)

Disc title (Units featuring CD text/MD only)

Track title (Units featuring CD text/MD only)

Successively play the beginning of each disc on a changer

until you find the one that you want to listen to.

Starting the disc scan:

Press the D.SCN button. "D-Scan ON" is displayed and the first

10 seconds of each disc are played, in the order in which they

are loaded on the changer.

NOTE

• You can give names to discs through the presetting disc name

function (see p24).

Note that depending on the unit, display may not be possible.

• If you try to display the name of a disc that does not have one,

"NO NAME" is displayed instead.

• When there is an attempt to display the title of a disc for which

the disc title/track title has not been recorded, "NO TEXT" is

displayed for CD and "NO TITLE/NO NAME" is displayed for

MD.

• Depending on the type of characters of the CD Text, some

characters may not be displayable.

The disc number currently being heard blinks in the display.

Stopping to Listen to the Disc Being Scanned:

Press the 38 or D.SCN button again to stop the scan and keep

on listening to the disc normally.

NOTE

• The disc scan function is cancelled when you eject the disc.

• The disc scan function only scans each disc on the changer

once.

• "LOAD" is displayed when discs are being exchanged on the

disc changer.

— 23 —

CD/External disc control features

A press of the 38 button exits the disc name preset mode.

Operations can be followed again from Step 2 at a time such

as this, and the characters to be input are selected using the

procedure described below.

Press the DISC+ or DISC– button to display the desired

character. Besides the alphabet (capital letters only) and

numbers, you can choose the following characters: /, +, –, *,

=, <, >, [ and ].

Presetting Disc Names (DNPS)

Store the names of discs to be displayed when played.

Play the disc whose name you want to preset.

Egnlish

NOTE

• This function is not available for disc changers that do not

feature the Disc Name Preset function.

• This procedure is not to be used to store the disc and track

titles for MDs that you record.

Continue steps 3 and 4 until all the characters are chosen for

the name.

• The disc name preset function cannot be used when a disc title

name or track title is displayed.

Press the NAME.S button.

The disc name is stored and the disc name preset mode is

cancelled.

Hold down the NAME.S button for two seconds or more.

"NAME SET" is displayed and the disc name preset mode is

If you make no entry in a 10-second period, the name will be

stored with the characters input so far.

entered.

The cursor blinks in the position where character input can be

made.

NOTE

• The number of characters and discs whose names can be

stored will differ depending on the disc changer that is

connected. Please see your disc changer manual for details.

Up to 8 characters and 30 CDs can be registered with this unit.

• Discs are identified by their total length and number of tracks. If

another disc happens to have the same specifications as one

that you have already stored a name for, the name will be

displayed for it, too.

• If you want to change the name of a disc, repeat steps 1 and 2

to display the name, and then repeat steps 3 and 4 to input the

changes.

• Pressing the reset button erases the disc names stored in this

unit, but does not erase the names stored in a disc changer.

Press either the 4 or ¢ button to move the cursor to the

desired position.

The 4 button moves the cursor to the left, and the ¢

button to the right.

Each time the 38 button is pressed, the characters to be

entered change as listed below.

^{Press the DISC}+ or DISC– button to display the desired

character.

Characters that can be displayed are as follows.

Alphabet (upper case): A ~ Z

Alphabet (lower case): a ~ z

Numerals and symbols: 0~9 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]

Special characters: á

›

Random Play

Play all the tracks on the current disc in random order.

NOTE

Press the RDM button to switch the random play function on

and off.

"Random ON" is displayed when random play is turned on.

The operation and characters that can be entered may change

as listed below, depending on the unit that is connected.

— 24 —

The display of the track number changes continuously as the

next track is being selected.

• The time needed for random selection depends on the number

of discs loaded in the disc magazine.

When the track has been selected, play starts.

The selected track number blinks in the display as it is being

played.

NOTE

(For disc changers)

When all the tracks on a certain disc have been played using the

random play function, the next disc on the changer starts playing

(with the random play function still turned on).

To change the track being heard, press the ¢ button.

Another track is selected and played.

NOTE

Random play is cancelled when you eject the disc.

Magazine Random Play

(Function of disc changers)

Play the tracks on all the discs in the disc changer in random

order.

Press the M.RDM button to switch the magazine random play

function on and off.

"M-Random ON" is displayed when magazine random play is

turned on.

The display of the disc and track numbers change continuously

as the next track is being selected.

When the disc/track has been selected, play starts.

The selected disc/track number blinks in the display as it is

being played.

NOTE

This function is not available with the following models:

KDC-C200/C300/C400/C301/C401

To change the track being heard, press the ¢ button.

Another disc/track is selected and played.

NOTE

• Magazine random play is cancelled when you eject the disc.

— 25 —

CD/External disc control features

Menu settings

Text Scroll

This function permits the text to be scrolled and the entire text

to be displayed. The scrolling method differs depending on the

setting of scrolling in the menu.

Egnlish

EJECT

To scroll manually:

Press the DISP button to display the disc title or the track title.

DISP

Holding down the DISP button for one second or more results

in one scrolling display of the titles.

To scroll automatically:

#1 - 4

Press the DISP button to display the disc title or the track title.

The titles will be displayed in one scrolling display.

NOTE

When the disc or track to be played changes, the title is

displayed in one scrolling display.

Holding down the DISP button for one second or more results

in one scrolling display of the titles.

Menu display

AUTO indicator

NOTE

Please see the menu settings (page 34) about switching between

manual scrolling and automatic scrolling.

NEWS indicator

™ indicator

— 26 —

Menu System

Touch Sensor Tone

This function produces a beep sound that accompanies button

operation. It can be switched on or off.

You can set the defaults for additional functions in the menu

mode.

Make a setting for each function, referring to the following

operations.

Display and setting:

"Beep ON" : Beep setting is on.

"Beep OFF" : Beep setting is off.

Enter the menu mode

Hold down the MENU button for one second or more.

"MENU" is displayed when the menu mode is entered.

The function that you can adjust is indicated with the current

settings displayed.

NOTE

The beep sound is not output from the preout jacks.

Selecting function to set

Press the FM button to search through the functions until you

see the one you want to adjust in the display.

Press the AM button to search through the functions

backward.

Example: If you want to switch the setting of the touch sensor

tone function from on to off, first search through the

functions until you see "Beep ON" in the display.

Manual Time Adjustment

Adjust the time manually.

NOTE

This adjustment is available only when the automatic time

adjustment is set to off. (page29)

Display and setting:

Select the display "Clock Adjust" during the selecting function

in the menu system.

Changing setting for currently displayed function

Press either the 4 or ¢ button.

Hold down either the 4 or ¢ button for two seconds or

more to enter the Manual time adjustment mode.

The time display will blink.

The setting will change for each function.

Example: The setting of the touch sensor tone will switch from

on to off, and "Beep OFF" is displayed.

• Adjusting the hours

Press the FM button to advance the hours, or press the AM

button to make the hours go back.

• Adjusting the minutes

Press the ¢ button to advance the minutes, or press the

Ending the menu mode

Press the MENU button.

4 button to make the minutes go back.

Press the MENU button to end the menu mode.

NOTE

Make sure to end the menu mode when finished.

If you fail to end the menu mode, several functions may not

operate properly, including the Traffic Information function and

the Alarm function.

— 27 —

Menu settings

Calendar Adjustment

Adjust the date for the unit so that you can use the calendar

function.

Select the display "Memo Mode" during the selecting function

in the menu mode.

Hold down either the 4 or ¢ button for two seconds or

more to enter the Memo mode.

The date display will blink.

Egnlish

Display and setting:

Select the display "Date Adjust" during the selecting function in

the menu system.

Selecting the set of the date and text to be displayed

Press the FM and AM button.

If you want to input a new text, select the blank display.

Hold down either the 4 or ¢ button for two seconds or

more to enter the Calendar adjustment mode.

The date display will blink.

Entering the month or day setting mode

Press the 4 and ¢ button to enter the month or day

setting mode.

The month display will blink enter the month setting mode, the

day display will blink enter the day setting mode.

Selecting the item (day, month, or year) to adjust

Press the 4 or ¢ button.

The item blinking in the display can be adjusted.

Adjusting the date

Changing the month or day

Press the FM and AM button.

Press the FM or AM button.

The item of the date blinking in the display will change.

Entering the text input mode

Press the MENU button to end the menu mode.

Press the ¢ button to enter the text input mode.

The cursor blinks in the position where character input can be

made.

Inputting / Changing the text

• Moving the cursor

Calendar Mode

Press the 4 and ¢ button.

• Changing the type of characters

Press the 38 button.

You can set the date formats of the calendar function.

Display and setting:

Each time the button is pressed, the type of characters

switches as follows.

Select the display "Date Mode" during the selecting function in

the menu system.

Press the 4 and ¢ button to select the date format you

want to show in the display.

The sample of the date format for today is displayed.

Alphabet (upper case): A ~ Z

Alphabet (lower case): a ~ z

Numerals and symbols: 0~9 @ ” ‘ ` % & ∗ + - = , . / \ < > [ ]

Special characters: á

Memo Mode

›

You can input the text to be displayed and set the date when

that text will appear in the display with the calendar function.

• Selecting the character

Press the FM and AM button.

Display and setting:

— 28 —

Press the MENU button to end the menu mode.

NOTE

• The text you selected automatically appears on the date you set

when the unit’s power is first turned on. (Calendar function)

Pressing the DISP button for one second or more scrolls the

display once, regardless of the text scroll setting.

Pressing a button other than the DISP button will cause the text

to disappear from the display.

• You can enter up to 32 characters for each text.

• The calendar function can be set up to 30 cases.

• To delete the date and text setting, set both the month and day

of the date to "00" or set all of the text to blanks.

Automatic Time Adjustment

With automatic time adjustment, you can set the clock time

automatically according to time data sent from RDS stations

(after receiving RDS signals for several minutes). You can also

set the time manually if the automatic time adjustment

function is turned off. The factory default is automatic time

adjustment.

Display and setting:

"SYNC ON" : Automatic time adjustment

"SYNC OFF" : Manual time adjustment

Adjusting Time Automatically:

Tune into an RDS station for 3 or 4 minutes.

The time adjusts automatically to the correct local time.

NOTE

The time is not adjusted when the RDS station you are tuned to

is not transmitting a time signal. Choose another RDS station in

such a case.

— 29 —

Menu settings

transmit the Mask Key’s signal.

Mask Key

• If the Mask Key’s signal does not be received correctly, the

display will return to "TRANSMIT 1" . In this case, repeat the

procedure in step 4.

If you have transmitted the Mask Key's signal once to the unit

in advance, you will have to transmit it once again if the unit

has been removed from the battery. This function helps

prevent theft.

Egnlish

Hold down the transmit button on the Mask key again until the

full transmit level indicator lights up in the display.

"APPROVED" will appear in the display, with the Mask key

function turning on.

When using the unit for the first time:

In order to deactivate the demonstration mode, be sure to

press the transmit button to transmit the Mask Key's signal.

If this procedure is not carried out, the control panel of the unit

will re-open in two seconds even with your vehicle's ignition

turned off.

If you press the RESET button or remove the battery:

The first time you turn the unit on again, "TRANSMIT 1" will

appear in the display, indicating the setting mode has been

entered. Repeat steps 5 and 6 above, and transmit the signal.

You can start operating the unit again when "APPROVED"

appears in the display.

Press the SRC button repeatedly to select the standby mode.

"ALL OFF" is displayed when the standby mode is selected.

Hold down the MENU button for one second or more.

"MENU" is displayed and the menu mode is turned on.

Press the FM button repeatedly until the "Mask key" appears in

the display.

Press the AM button to search in the other direction.

Selectable Illumination

You can switch the colour of the button illumination between

green and red.

Hold down either the 4 or ¢ button for two seconds or

more.

Display and setting:

"TRANSMIT 1" will appear in the display, indicating the setting

mode has been entered.

"Color Green" : The colour of the illumination is green.

"Color Red" : The colour of the illumination is red.

Hold down the transmit button on the Mask key until the full

transmit level indicator lights up in the display.

"TRANSMIT 2" will be displayed.

Contrast Adjustment

This adjustment permits easy viewing of the display.

Transmission part

Transmit button

Display and setting:

"Contrast 0" – "Contrast 10"

NOTE

The initial setting value is "5" .

NOTE

• Keep the Mask Key close to the signal sensor when you

— 30 —

the faceplate can be removed from the faceplate bracket.

Dimmer

You can dim the display.

Display and setting:

"OFF WAIT" : 0s / 3s / 5s / 10s / 15s / 20s / 25s (s=sec.)

NOTE

The dimmer function is not available for units if the dimmer cable

is not connected.

If you do not slide the faceplate lock switch during the period

which you have set, the unit’s power turns off after the control

panel is automatically hidden.

Display and setting:

"Dimmer ON" : The dimmer setting is on.

"Dimmer OFF" : The dimmer setting is off.

KEX/ec4/dB (Sound Coordinate system)

When this system is set to on, the sound coordinate factors

(Bass frequency, Bass quality, Bass extension, and Treble

frequency) appear during the audio control mode.

Switching Graphic Display

You can turn the movement of graphic display on and off.

The initial setting is ON.

Display and setting:

"Kex/ec4/dB set ON" : The sound coordinate factors appear and

"Graphic ON" : The graphic display works.

"Graphic OFF" : The graphic display does not work.

can be adjusted.

"Kex/ec4/dB set OFF" : The sound coordinate factors are not

appeared.

Black Mask

This function allows you to turn off the lower part of the

External Amp Control

Adjust the bass boost level of the external amplifier using the

main unit.

display if there is too much information in the display.

Display and setting:

"BLK MASK ON" : The display will turn on by using only the

upper part of the display and the IN

indicator.

"BLK MASK OFF" : The display will turn on by using the whole

part of the display.

Display and setting:

"AMP BASS FLT" : Bass boost level is flat.

"AMP BASS +6" : Bass boost level is low (+6dB).

"AMP BASS +12" : Bass boost level is high (+12dB).

NOTE

As of December 1999, the power amplifiers controllable by the

main unit are as follows:

KAC-X501F/PS501F/X401M/PS401M/X301T/PS301T/X201T/PS201T

Time setting for removing the faceplate

You can set the interval during which the open control panel

cannot reverse to be hidden. During the period you have set,

— 31 —

Menu settings

off the function.

Manual Open Button Setting

By pressing the button hidden behind the upper left part of the

faceplate during forced closing, you can open the faceplate.

Follow the directions below to preset the number of times that

this button needs to be pressed in order to open the faceplate.

Egnlish

Local Seek Function

With the local seek function turned on, auto seek tuning skips

stations with relatively poor reception.

Display and setting:

"OPEN SW 1" – "OPEN SW 3"

NOTE

Display and setting:

"Local.S ON" : The local seek function is on.

"Local.S OFF" : The local seek function is off.

The initial setting value is "1" .

News Bulletin Function

Selecting Tuning Mode

with PTY News Timeout Setting

You can choose from three tuning modes: auto seek, preset

station seek, and manual. The "AUTO 1" indicator lights up

when auto seek tuning is selected, and the "AUTO 2" indicator

lights when preset station seek tuning is selected.

You can arrange to have news bulletins interrupt your current

listening source, including other radio stations. When the

News Bulletin function is on, the PTY News Timeout setting

allows you to set the interval during which further news

interruption cannot take place. You can adjust the PTY news

interruption period from 10 to 90 minutes for each journey.

Display and setting:

"Auto 1" : Auto seek tuning mode

"Auto 2" : Preset station seek tuning mode

"Manual" : Manual tuning mode

Display and setting:

"NEWS OFF/ 00min/ 10min/ 20min/ 30min/ 40min/ 50min/

60min/ 70min/ 80min/ 90min"

(min= minutes)

: When you select the news interruption timeout interval, the

News function turns on and the NEWS indicator lights up.

When a news bulletin is received, "NEWS" will be displayed

and reception will begin at the preset volume.

Auto Memory Entry

You can automatically store all the receivable frequencies in

the band currently being listened to, and then recall them with

the touch of a button later. This function is especially useful

when you are travelling and do not know what stations are

available. Up to 6 frequencies can be stored this way.

NOTE

• If you choose the "20min" setting, further news bulletins will not

be received for 20 minutes once the first news bulletin is

received.

• This function is only available if the desired station sends PTY-

code for news bulletin or belongs to <Enhanced Other

Network>-Network sending PTY-code for news bulletin.

• If you turn on the news bulletin function in the MW/LW band,

the band is switched automatically to the FM band.

However, the MW/LW band is not returned to when you turn

Display and setting:

Select the display "Auto-Memory" during the selecting function

in the menu system.

Hold down either the 4 or ¢ button for two seconds or

more to start auto memory function.

— 32 —

The numbers of the preset station buttons showed in order.

When all the stations in a certain band are stored in the preset

memory, the auto memory entry stops. The tuner then plays

the last station received.

AF (Alternative Frequency) Function

When poor reception is experienced, automatically switch to

another frequency broadcasting the same programme in the

same RDS network with better reception.

The ™ indicator lights up when the AF function is turned

on.

NOTE

• When the AF function is turned on whilst auto memory entry

takes place, only RDS stations (i.e., stations with RDS

capability) are stored. RDS stations that have been preset for

FM1 cannot also be preset in FM2 or FM3.

• When the local seek function is turned whilst auto memory

entry takes place, stations with poor reception are not stored.

• When the Traffic Information function is on , only the local

traffic information station frequency will be stored.

Display and setting:

"AF ON" : The AF function is on.

"AF OFF" : The AF function is off.

NOTE

• When no other stations with stronger reception are available for

the same programme in the RDS network, you may hear the

incoming broadcast in bits and snatches. Turn off the AF

function in such a case.

• The AF function can be turned on or off even when the standby

mode has been turned on. If the power is on, the AF function

tunes in to stations that offer good reception.

Cancelling Auto Memory Entry During Its Operation:

Press the MENU button whilst auto memory entry is taking

place to stop the process.

Recalling a Preset Station:

Press the preset station button (#1-6) for the desired station.

The number of the recalled station is displayed.

Restricting RDS Region (Region Restrict Function)

You can choose whether or not to restrict the RDS channels,

received with the AF function for a particular network, to a

specific region. When the Region Restrict Function is on, the

region is restricted and the REG indicator is turned on.

Display and setting:

"Regional ON" : The Region Restrict Function is on.

"Regional OFF" : The Region Restrict Function is off.

NOTE

Sometimes stations in the same network broadcast different

programmes or use different programme service names.

— 33 —

Menu settings

Auto TP Seek Function

Text Scroll

When the TI function is on and poor reception conditions are

experienced when listening to a traffic information station,

another traffic information station with better reception will be

searched for automatically. This function is on, when unit is

first powered on.

This function permits the CD text, MD title, Radio text, and

Calender function to be scrolled and the entire text to be

displayed. Switching Switching between manual scrolling and

automatic scrolling is permitted. The factory default is manual

scrolling.

Egnlish

Display and setting:

"ATPS ON" : The Auto TP Seek Function is on.

If the traffic information station you are tuned to

experiences poor reception, this function

automatically seeks another TP station.

"ATPS OFF" : The Auto TP Seek Function is off.

"Scroll Auto" : Automatic scrolling

"Scroll Manu" : Manual scrolling

Monaural Reception

When poor stereo reception is experienced, this function will

reduce noise and improve listening conditions.

Display and setting:

"MONO ON" : The monaural reception is on.

"MONO OFF" : The monaural reception is off.

— 34 —

speaker connector in your vehicle.

5. Take Connector A on the wiring harness and connect it to the

external power connector on your vehicle.

6. Connect the wiring harness connector to the unit.

7. Install the unit in your car.

Accessories

External view

......... Number of items

8. Reconnect the - terminal of the battery.

9. Press the left part at the upper side of the faceplate once to

make the faceplate control panel appear.

.........1

2CAUTION

.........1

• If your car is not prepared for this special connection-system,

consult your KENWOOD dealer.

• Only use antenna conversion adapters (ISO-JASO) when the

antenna cord has an ISO plug.

• Make sure that all cable connections are securely made by

inserting jacks until they lock completely.

• If your vehicle's ignition does not have an ACC position, or if

the ignition cable is connected to a power source with constant

voltage such as a battery cable, the power will not be linked

with the ignition (i.e., it will not turn on and off along with the

ignition). If you want to link the unit's power with the ignition,

connect the ignition cable to a power source that can be turned

on and off with the ignition key.

• If the fuse blows, first make sure that the cables have not

caused a short circuit, then replace the old fuse with one with

the same rating.

2CAUTION

• Do not let unconnected cables or terminals touch metal on the

car or anything else conducting electricity. To prevent short

circuits, also do not remove the caps on the ends of the

unconnected cables or the terminals.

The use of any accessories except for those provided might

result in damage to the unit. Make sure only to use the

accessories shipped with the unit, as shown above.

• Connect the speaker cables correctly to the terminals to which

they correspond. The unit may receive damage or fail to work if

you share the - cables and/or ground them to any metal part

in the car.

• After the unit is installed, check whether the brake lamps,

indicators, wipers, etc. on the car are working properly.

• Insulate unconnected cables with vinyl tape or other similar

material.

Installation Procedure

1. To prevent short circuits, remove the key from the ignition and

disconnect the -terminal of the battery.

• Some disc changers need conversion cables for connection.

See the section on "Safety Precautions" for details.

• If the console has a lid, make sure to install the unit so that the

faceplate does not hit the lid when closing and opening.

2. Make the proper input and output cable connections for each

unit.

3. Connect the cable on the wiring harness.

4. Take Connector B on the wiring harness and connect it to the

• Mount the unit so that the mounting angle is 30° or less.

— 35 —

Connecting Cables to Terminals

Connector Function Guide

Pin Numbers for

Antenna Cord (ISO)

FM/AM

antenna input

Cable Colour

Functions

ISO Connectors

Antenna Conversion Adaptor (ISO–JASO) (Accessory3)

Front right output (Red)

External Power

Connector

Egnlish

A–4

Yellow

Battery*

Front left output (White)

Ignition (ACC)*

Power Control

Rear right output (Red)

A–5

A–6

A–7

Blue/White

Orange/White Dimmer

Red

Rear left output (White)

Ignition (ACC)*

Battery*

A–8

Black

Earth (Ground)

Connection

KENWOOD disc changer/DAB control input/

Display Data Output Jack

Outputs data representing the unit's current state,

causing it to appear in the external display.

To connect to this jack, a converting adapter

(optional) is necessary.

Speaker

Connector

B–1

Purple

Purple/Black

Gray

Gray/Black

White

White/Black

Green

Rear Right (+)

Rear Right (–)

Front Right (+)

Front Right (–)

Front Left (+)

Front Left (–)

Rear Left (+)

Rear Left (–)

Fuse(10A)

B–2

B–3

B–4

B–5

B–6

B–7

B–8

NOTE

To connect the Disc changer or DAB unit,

consult each manual.

Wiring harness

(Accessory1)

External amplifier control cable

(Pink / Black)

To "EXT.AMP.CONT." terminal of the

amplifier having the external amp

control function.

EXT.CONT.

Green/Black

* KDC-7080R: Battery cable (Yellow)

* KDC-7080RV: Ignition cable (Red)

TEL mute cable (Brown)

Connect to the terminal that is

grounded when either the telephone

rings or during conversation.

TEL MUTE

(KDC-7080R

only)

* KDC-7080R: Ignition cable (Red)

* KDC-7080RV: Battery cable (Yellow)

(KDC-7080RV

only)

NOTE

To connect the KENWOOD navigation

system, consult your navigation manual.

Power control/ Motor antenna

A–7 Pin (Red)

control cable (Blue/White)

Connect either to the power control

P.CONT

A–4 Pin (Yellow)

terminal when using the optional

ANT.CONT.

power amplifier, or to the antenna

control terminal in the vehicle.

Connector A

Connector B

NOTE

If no connections are

made, do not let the cable

come out from the tab.

— 36 —

Connecting Cables to Terminals

Installtion

■

2WARNING

Installation

Connecting the ISO Connector (see p.36)

The pin arrangement for the ISO connectors depends on the

type of vehicle you drive. Make sure to make the proper

connections to prevent damage to the unit.

Firewall or metal support

The default connection for the wiring harness is described in 1

below. If the ISO connector pins are set as described in 2 or 3,

make the connection as illustrated.

Screw (M4X8)

(commercially

available)

1 The A-7 pin (red) of the vehicle's ISO connector is linked with

the ignition, and the A-4 pin (yellow) is connected to the

constant power supply.

Unit

Vehicle

Ignition cable (Red)

A–7 Pin (Red)

Bend the tabs of the

mounting sleeve

with a screwdriver or

similar utensil and

attach it in place.

Battery cable (Yellow)

A–4 Pin (Yellow)

Self-tapping

screw

(commercially

available)

Metal mounting

strap

(commercially

available)

2 The A-7 pin (red) of the vehicle's ISO connector is connected

to the constant power supply, and the A-4 pin (yellow) is

linked to the ignition.

NOTE

Unit

Vehicle

Make sure that the unit is installed securely in place. If the unit

is unstable, it may malfunction (eg, the sound may skip).

Ignition cable (Red)

A–7 Pin (Red)

Battery cable (Yellow)

A–4 Pin (Yellow)

3 The A-7 pin (red) of the vehicle's ISO connector is not

connected to anything, whilst the A-4 pin (yellow) is connected

to the constant power supply (or both the A-7 (red) and A-4

(yellow) pins are connected to the constant power supply).

Unit

Vehicle

Connect to a power source that can be

turned on and off with the ignition key.

Ignition cable (Red)

2CAUTION

To attach this unit, make sure the front of the control panel faces

you and fit it into the mounting sleeve by pressing the four corners

of the hard rubber frame at the same time.

Battery cable (Yellow)

A–4 Pin (Yellow)

Do not apply strong pressure to other sections than the corners;

otherwise troubles such as the impossibility of opening or closing

the panel may result.

— 37 —

Removing the Unit

■

Removing the Unit

■

Removing the hard rubber frame

Insert the removal tool into the indentations in the hard rubber

frame, and pull it gently until the lock is released.

Make the faceplate control panel appear.

NOTE

When the control panel of the faceplate is hidden, the unit will

be locked by the sleeve, making it more difficult to remove

the unit.

Egnlish

Refer to the section “Removing the hard rubber frame” and

then remove the hard rubber frame.

Remove the screw (M4×8) on the back panel.

Insert the removal tool deeply, as illustrated, with the L on the

left and the R on the right.

Screw (M4X8)

(commercially

available)

Accessory4

Removal tool

Accessory2

Removal tool

Push upward the both

tools, as shown, and pull

the unit toward you until it

is halfway out. The unit

may drop if you pull it out

completely.

Pull the unit all the way out

with your hands, being

careful not to drop it.

— 38 —

Locking the faceplate to the unit

■

Locking the faceplate to the unit

If you want to lock the faceplate to the unit so that it does not

fall off, follow the directions below.

Refer to the function "Removing the faceplate (page 12)" and

remove the faceplate.

Insert the provided screw into the hole at the centre of the

bottom side of the faceplate which you have removed from

the unit.

Accessory5

Refer to the section "Removing the faceplate (page 12)" and

then reattaching the faceplate.

2CAUTION

Never insert the taptite screws (ø2 × 6 mm) in any other screw

holes than the one specified. If you insert it in another hole, it

will contract and may cause damage to the mechanical parts

inside the unit.

— 39 —

Troubleshooting Guide

What might appear to be a malfunction in your unit may just be the result of slight misoperation or miswiring.

Before calling service, first check the following table for possible problems.

PROBLEM

POSSIBLE CAUSE

SOLUTION

The power does not turn on.

The fuse has blown.

After checking for short circuits in the cables, replace

the fuse with one having the same rating.

Egnlish

No ACC position on vehicle ignition.

The Attenuator function is turned on.

Connect the same cable to the ignition as the battery cable.

Turn off the Attenuator function.

No sound can be heard, or the

volume is low.

The fader and/or balance settings are set all the way to

one side.

Reset the fader and/or balance settings.

The input/output cables or wiring harness are connected

incorrectly.

Reconnect the input/output cables and/or the wiring

harness correctly. See the section on "Connecting

Cables to Terminals".

The values of “Volume offset” are low.

Increase the values of “Volume offset”. (see p. 10)

Press the reset button on the unit (see page 4).

Nothing happens when the

buttons are pressed.

The computer chip in the unit is not functioning normally.

A speaker cable may be pinched by a screw in the car.

The speakers are not wired correctly.

Check the speaker wiring.

The sound quality is poor or

distorted.

Reconnect the speaker cables so that each output

terminal is connected to a different speaker.

Radio reception is poor.

The car antenna is not extended.

Pull out the antenna all the way.

The antenna control cable is not connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The memory is erased when

the ignition is turned off.

The battery cable has not been connected to the proper

terminal.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The ignition and battery cable are incorrectly connected.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

A CD ejects as soon as it is

loaded.

The CD is upside-down.

The CD is quite dirty.

Load the CD with the labelled side up.

Clean the CD, referring to the section on "Cleaning CDs"

(see page 6).

The sound skips on a CD.

The CD is scratched or dirty.

Random play has been selected.

— 40 —

Clean the CD, referring to the section on "Cleaning CDs"

(see page 6).

The specified track does not

play.

Turn off the random play function.

Troubleshooting Guide

PROBLEM

POSSIBLE CAUSE

SOLUTION

The faceplate does not open or

close.

The faceplate is incorrectly attached.

Reattach the faceplate correctly, See the section on

"Removing the Faceplate".(page.12)

The TEL mute function does

not work.

The TEL mute cable is not connected properly.

Connect the cable correctly, referring to the section on

"Connecting Cables to Terminals".

The TEL mute function turns

on even though the TEL mute

cable is not connected.

The TEL mute cable is touching a metal part of the car.

Pull the TEL mute cable away from the metal part of

the car.

CD/MD/External disc control mode

PROBLEM

POSSIBLE CAUSE

SOLUTION

The disc control mode cannot

be selected.

No cable has been connected to the disc changer input

terminal on the unit.

Connect the cable to the disc changer input terminal on

the unit.

The specified disc does not

play, but another one plays

instead.

The specified CD is very dirty.

Clean the CD.

The CD is upside-down.

Load the CD with the labelled side up.

The disc is loaded in a different slot from that specified.

Eject the disc magazine and check the number for the

specified disc.

The disc is severely scratched.

Try another disc instead.

The sound skips.

Something is touching the disc changer.

The CD is scratched or dirty.

Remove whatever is touching it.

If skipping happens at the same place when the car is

stopped, something is wrong with the CD. Clean the CD.

The display shows that the

changer is being played, but no

sound can be heard.

The computer chip in the unit is not functioning normally.

Press the reset button on the unit (see page 4).

Turn off the random play or magazine random play

function.

The specified track does not

play.

Random play or magazine random play has been

selected.

Track repeat, disc repeat, track

scan, disc scan, random play,

and magazine random play

start by themselves.

The setting is not cancelled.

The settings for these functions remain on until the

setting to off or the disc ejected, even if the power is

turned off or the source changed.

If the following situations, consult your nearest service centre:

• Even though the disc changer is connected, the Disc Changer Mode is not on, with "AUX" showing in the display during the Changer Mode.

• Even though no device (KCA-S210A, CA-C1AX, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) is connected, the AUX Mode is entered when switching modes.

— 41 —

Troubleshooting Guide

The following messages are displayed when certain problems are occurring in your system. Take the

recommended actions.

No disc magazine has been loaded in the changer. The disc magazine is not completely loaded.

EJECT

] Load the disc magazine properly.

No CD in the unit.

] Insert the CD.

Egnlish

No disc has been loaded in the disc magazine.

NO DISC

E-04

] Load a disc into the disc magazine.

No disc has been loaded in the disc magazine.

] Load a disc into the disc magazine.

The CD is very dirty. The CD is upside-down. The CD is scratched a lot.

] Clean the CD and load it correctly.

Nothing has been recorded on the MD.

BLANK

No tracks are recorded on the MD, although it has a title.

NO TRACK

NO PANEL

The faceplate of the slave unit being connected to this unit has been removed.

] Replace it.

The unit is malfunctioning for some reason.

E-77

E-99

] Press the reset button on the unit. If the "E- 77", code does not disappear, consult your nearest service centre.

Something is wrong with the disc magazine. Or the unit is malfunctioning for some reason.

] Check the disc magazine. And then, press the reset button on the unit.

If the "E- 99" code does not disappear, consult your nearest service center.

The protective circuit in the unit activates when the temperature inside the automatic disc changer exceeds 60°C (140°F),

HOLD

stopping all operation.

] Cool down the unit by opening the windows or turning on the air conditioner. As the temperature falls below 60°C (140°F),

the disc starts playing again.

If this indicator blinks, the CD player is malfunctioning.

] Eject the CD and try inseting it again.

If the CD cannot be ejected, press the eject button and hold it in until the CD is ejected.

— 42 —

Specifications

Specifications subject to change without notice.

FM tuner section

Audio section

Frequency range (50 kHz Space)..............87.5 MHz – 108.0 MHz

Usable sensitivity (S/N=26dB) ..................................0.7 µV/75 Ω

Quieting Sensitivity (S/N=46dB).................................1.6 µV/75 Ω

Frequency response ( 3.0 dB)..............................30 Hz – 15 kHz

Signal to Noise ratio (MONO)..............................................65 dB

Selectivity (DIN) (400kHz).................................................≥ 80 dB

Stereo separation (1 kHz) ....................................................35 dB

Maximum output power.................................................45 W × 4

Output power (DIN 45324, +B=14.4V)...........................28 W × 4

Tone action

Bass: ...........................................................100 Hz 10 dB

Treble: .........................................................10 kHz 10 dB

Preout level / Load (during CD play).....................1800 mV/10 kΩ

Preout impedance............................................................≤ 600 Ω

MW tuner section

General

Frequency range (9kHz Space)......................531 kHz – 1611 kHz

Usable sensitivity (S/N=20dB) .............................................25 µV

Operating voltage .............................14.4 V (11 – 16 V allowable)

Current consumption.............................................................10 A

Installation size (W × H × D) ..........................182 × 53 × 162 mm

Weight ................................................................................1.9 kg

LW tuner section

Frequency range .............................................153 kHz – 281 kHz

Usable sensitivity (S/N=20dB) .............................................45 µV

CD player section

Laser diode....................................................GaAlAs (λ=780 nm)

Digital filter (D/A) .....................................8 Times Over Sampling

D/A Converter .......................................................................1 Bit

Spindle speed ..............................................500 – 200 rpm (CLV)

Wow & Flutter........................................Below Measurable Limit

Frequency response ( 1 dB).................................10 Hz – 20 kHz

Total harmonic distortion (1 kHz).......................................0.01 %

Signal to Noise ratio ................................................93 dB (1 kHz)

Dynamic range ....................................................................93 dB

Channel separation..............................................................85 dB

— 43 —

Microsoft Software Office Home And Student 2013 79G03550 User Manual
Kenwood KDC 205CR User Manual
Hitachi Travelstar HTS725032A7E635 User Manual
Fujitsu MAS3735 User Manual
Emerson GP815 User Manual
DeLonghi DC51TT Series User Manual
Cuisinart DCC 2900 User Manual
Barracuda Networks ST320430A User Manual
Audiovox CDM 8500 User Manual
APC Net Shelter SC 260W User Manual