JVC UX MD9000R User Manual

ULTRA MICRO COMPONENT SYSTEM  
ULTRA-MIKRO-KOMPONENTEN-SYSTEM  
SYSTEME DE COMPOSANTS ULTRA MICRO  
ULTRA MIKRO KOMPONENTENSYSTEEM  
SISTEMAS DE COMPONENTES ULTRA MICRO  
SISTEMA AD ULTRA MICROCOMPONENTI  
UX-MD9000R  
REMOTE CONTROL RM-RXUMD9000R  
DIMMER  
SLEEP  
CLOCK FM MODE TAPE/AUX  
TAPE/AUX  
AHB.  
AUTO  
SUPER PRO PRESET  
PROGRAM RANDOM REPEAT  
BASS  
TREBLE  
CANCEL  
EDIT  
DISPLAY  
/CHARA  
/TITLE  
<
UP  
SET  
>
DOWN  
PTY/EON  
MD  
DISPLAY MODE  
CD  
STANDBY  
TUNER  
BAND  
VOLUME  
PHONES  
ULTRA MICRO COMPONENT SYSTEM  
UX-MD9000R  
INSTRUCTIONS  
BEDIENUNGSANLEITUNG  
MANUEL D’INSTRUCTIONS  
GEBRUIKSAANWIJZING  
MANUAL DE INSTRUCCIONES  
ISTRUZIONI  
For Customer Use:  
Enter below the Model No. and Serial No.  
which are located either on the rear, bot-  
tom or side of the cabinet. Retain this  
information for future reference.  
Model No.  
Serial No.  
LVT0053-001B  
[E]  
Caution: Proper Ventilation  
To avoid risk of electric shock and fire, and to prevent damage, locate  
the apparatus as follows:  
Voorzichtig: Goede ventilatie vereist  
Om brand, elektrische schokken en beschadiging te voorkomen, moet  
u het toestel als volgt opstellen:  
1 Front:  
1 Voorkant:  
No obstructions and open spacing.  
2 Sides/ Top/ Back:  
Geen belemmeringen en voldoende ruimte.  
2 Zijkanten/boven-/onderkant:  
No obstructions should be placed in the areas shown by the  
dimensions below.  
Geen belemmeringen plaatsen in de hieronder aangegeven  
zones.  
3 Bottom:  
3 Onderkant:  
Place on the level surface. Maintain an adequate air path for venti-  
lation by placing on a stand with a height of 10 cm or more.  
Op vlakke ondergrond plaatsen. Voldoende ventilatieruimte voorz-  
ien door het toestel op een onderstel met een hoogte van 10 cm of  
meer te plaatsen.  
Vorsicht: Ausreichende Belüftung  
Precaucion: ventilación correcta  
Zur Vermeidung von elektrischen Schlägen, Feuer und sonstigen  
Schäden sollte das Gerät unter folgenden Bedingungen aufgestellt  
werden:  
Para evitar el riesgo de descargas eléctricas e incendio y prevenir  
posibles daños, instale el equipo en un lugar que cumpla los sigu-  
ientes requisitos:  
1 Vorderseite:  
1 Parte frontal:  
Hindernisfrei und gut zugänglich.  
Sin obstrucciones, espacio abierto.  
2 Seiten- und Rückwände:  
2 Lados/parte superior/parte posterior:  
Hindernisfrei in allen gegebenen Abständen (s. Abbildung).  
3 Unterseite:  
No debe haber ninguna obstrucción en las áreas mostradas por  
las dimensiones de la siguiente figura.  
Die Stellfläche muß absolut eben sein. Sorgen Sie für ausre-  
ichende Luftzufuhr durch Aufstellung auf einem Stand mit mindes-  
tens 10 cm Höhe.  
3 Parte inferior:  
Sitúe el equipo sobre una superficie nivelada. Mantenga un espa-  
cio adecuado para permitir el paso del aire y una correcta venti-  
lación, situando el equipo sobre un soporte de 10 o más cm de  
allura.  
Attention: Aération correcte  
Attenzione: Per una corretta ventilazione  
Per prevenire il rischio di scosse elettriche e di incendio ed evitare pos-  
sibili danni, collocare le apparecchiature nel modo seguente:  
1 Parte anteriore:  
Pour prévenir tout risque de décharge électrique ou d’incendie et  
éviter toute détérioration, installez l’appareil de la manière suivante:  
1 Avant:  
Bien dégagé de tout objet.  
Nessun ostacolo e spazio libero.  
2 Côtés/dessus/dessous:  
2 Lati/Parte superiore/Retro:  
Assurez-vous que rien ne bloque les espaces indiqués sur le  
schéma ci-dessous.  
Lasciare libere le zone indicate dalle dimensioni di seguito.  
3 Base:  
3 Dessous:  
Collocare su una superficie piana. Consentire un’adeguata venti-  
lazione dell’impianto appoggiandolo su un tavolinetto alto almeno  
10 cm.  
Posez l’appareil sur une surface plane et horizontale. Veillez à ce  
que sa ventilation correcte puisse se faire en le plaçant sur un sup-  
port d’au moins dix centimètres de hauteur.  
Front view  
Vorderansicht  
Face  
Vooraanzicht  
Vista frontal  
Vista frontale  
Side view  
Seitenansicht  
Côt  
Zijaanzicht  
Vista lateral  
15 cm  
15 cm  
Vista laterale  
15 cm  
15 cm  
STANDBY  
1 cm  
1 cm  
15 cm  
UX-MD9000R  
PHONES  
ULTRA MICRO COMPONENT SYSTEM  
UX-MD9000R  
UX-MD9000R  
10 cm  
G-2  
IMPORTANT FOR LASER PRODUCTS/ WICHTIGER HINWEIS FÜR LASER-PRODUKTE / IMPORTANT POUR LES PRODUITS LASER /  
BELANGRIJKE INFORMATIE VOOR LASERPRODUKTEN / IMPORTANTE PARA LOS PRODUCTOS LÁSER / IMPORTANTE PER I PRO-  
DOTTI LASER  
REPRODUCTION OF LABELS/ANBRINGUNGSORTE FÜR LASER-PRODUKTE/REPRODUCTION DES ETIQUETTES/VERKLARING VAN  
DE LABELS/REPRODUCCIÓN DE ETIQUETAS/RIPRODUZIONE DELLE ETICHETTE  
1 CLASSIFICATION LABEL, PLACED ON EXTERIOR SURFACE  
2 WARNING LABEL, PLACED INSIDE THE UNIT  
1 KLASSIFIZIERUNGSHINWEIS BEFINDET SICH AUF DER AUS-  
2 WARNETIKETTE IM GERÄTEINNEREN  
SENSIETE  
2 ETIQUETTE D’AVERTISSEMENT PLACÉE À LINTERIEUR DE  
1 ÉTIQUETTE DE CLASSIFICATION, PLACÉE SUR LA SURFACE  
LAPPAREIL  
EXTÉRIEURE  
2 WAARSCHUWINGSLABEL, IN HET APPARAAT  
1 CLASSIFICATIE-ETIKET AAN DE BUITENKANT VAN HET APPA-  
RAAT  
2 ETIQUETA DE ADVERTENCIA, PEGADA EN EL INTERIOR DE  
LA UNIDAD  
1 ETIQUETA DE CLASIFICACION, PROVISTA SOBRE LA SUPER-  
FICIE EXTERIOR  
2 ETICHETTA DI AVVERTENZA, SITUATA ALLINTERNO  
DELLAPPARECCHIO  
1 ETICHETTA DI CLASSIFICAZIONE POSTA ALLESTERNO  
1. CLASS 1 LASER PRODUCT  
1. KLAS 1 LASERPRODUKT  
2. DANGER: Invisible laser radiation when open and interlock failed  
or defeated. Avoid direct exposure to beam.  
3. CAUTION: Do not open the top cover. There are no user service-  
able parts inside the Unit; leave all servicing to qualified service  
personnel.  
2. GEVAARLIJK: Onzichtbare laserstraling wanneer open en de  
beveiliging faalt of uitgeschakeld is. Voorkom het direkt blootstaan  
aan de straal.  
3. VOORZICHTIG: De bovenkap niet openen. Binnenin het toestel  
bevinden zich geen door de gebruiker te repareren onderdelen:  
laat onderhoud over aan bekwaam vakpersoneel.  
1. LASER-PRODUKT DER KLASSE 1  
2. GEFAHR: Unsichtbare Laserstrahlung bei Öffnung und fehler-  
hafter oder beschädigter Spre. Direkten Kontakt mit dem Strahl  
vermeiden!  
1. PRODUCTO LASER CLASE 1  
2. PELIGRO: En el interior hay radiación láser invisible. Evite el con-  
tacto directo con el haz.  
3. ACHTUNG: Das Gehäuse nicht öffnen. Das Gerät enthält keiner-  
lei Teile, die vom Benutzer gewartet werden können. Überlassen  
Sie Wartungsarbeiten bitte qualifizierten Kundendienst-Fachleu-  
ten.  
3. PRECAUCIÓN: No abra la tapa superior. En el interior de la  
unidad no existen piezas reparables por el usuario; deje todo ser-  
vicio técnico en manos de personal calificado.  
1. PRODUIT LASER CLASSE 1  
1. PRODOTTO LASER CLASSE 1  
2. ATTENTION: Radiation laser invisible quand l’appareil est ouvert  
ou que le verrouillage est en panne ou désactivé. Eviter une expo-  
sition directe au rayon.  
2. PERICOLO: Radiazione laser invisibile quando l’apparecchio è  
aperto ed il dispositivo di sicurezza è guasto o disattivato. Evitare  
l’esposizione diretta ai raggi.  
3. ATTENTION: Ne pas ouvrir le couvercle du dessus. Il n’y a  
aucune pièce utilisable à l’intérieur. Laisser à un personnel qualifié  
le soin de réparer votre appareil.  
3. ATTENZIONE: Non aprire il coperchio superiore. Non vi sono parti  
adoperabili dall’utente all’interno di questo apparecchio; lasciare  
tutti i controlli a personale qualificato.  
G-3  
Thank you for purchasing the JVC Ultra Micro Component System.  
We hope it will be a valued addition to your home, giving you years of enjoyment.  
Be sure to read this instruction manual carefully before operating your new stereo system.  
In it you will find all the information you need to set up and use the system.  
If you have a query that is not answered by the manual, please contact your dealer.  
Features  
Here are some of the things that make your System both powerful and simple to use.  
The controls and operations have been redesigned to make them very easy to use, freeing you to just enjoy the music.  
With JVC’s COMPU PLAY you can turn on the System and automatically start the Radio, CD Player, MD  
Player with a single touch.  
The System incorporates Active Hyper Bass Super PRO circuitry to faithfully reproduce low frequency sounds.  
A 45-station preset capability (30 FM and 15 AM (MW/LW)) in addition to auto-seek and manual tuning.  
Versatile CD options include repeat, random and program play.  
Versatile MD Player provides playback function, recording function, editing function of the tracks in the MD, title function to give title to  
the MD and tracks.  
Sampling rate converter which supports 3 digital sources Incorporated.  
32 kHz, 44.1 kHz and 48 kHz.  
Timer functions; set the system to automatically come on, switch off.  
The System is compatible with RDS (Radio Data System) broadcasting.  
The EON data enables you to standby for desired information.  
The PTY Search function searches for programmes in the category you wish.  
IYnoaudcdaitniocno,nRnaedctiovaTreioxut scaenxtbeerndailspulnaiytse,dsuucsihnagsdaatCaDsepnltabyyers,ttaatpioend.eck, etc.  
How This Manual Is Organized  
Basic information that is the same for many different functions - e.g. setting the volume - is given in the section ‘Common Operations’,  
and not repeated under each function.  
The names of buttons/controls and display messages are written in all capital letters: e.g. TUNER BAND, “NO DISC”.  
System functions are written with an initial capital letter only: e.g. Normal Play.  
Use the table of contents to look up specific information you require.  
We’ve enjoyed making this manual for you, and hope it serves you in enjoying the many features built into your System.  
IMPORTANT CAUTIONS  
1.Installation of the System  
Select a place which is level, dry and neither too hot nor too cold. (Between 5°C and 35°C or 41°F and 95°F.)  
Leave sufficient distance between the System and a TV.  
Do not use the System in a place subject to vibrations.  
2.Power cord  
Do not handle the power cord with wet hands!  
Some power is always consumed as long as the power cord is connected to the wall outlet.  
When unplugging the System from the wall outlet, always pull the plug, not the power cord.  
3.Malfunctions, etc.  
There are no user serviceable parts inside. In case of system failure, unplug the power cord and consult your dealer.  
Do not insert any metallic object into the System.  
Table of Contents  
■  
Features ...............................................................................1  
How This Manual Is Organized ..........................................1  
IMPORTANT CAUTIONS ................................................1  
Using the Timers ................................................... 22  
Information on MDs (Minidiscs)............................ 23  
MD (Minidisc) Error Messages.............................. 24  
Minidisc limitations................................................ 25  
Rules of Digital Dubbing........................................ 25  
Care And Maintenance ......................................... 26  
Troubleshooting .................................................... 27  
Specifications ........................................................ 28  
Getting Started .........................................................2  
Common Operations ................................................6  
Using the Tuner ........................................................8  
Using the CD Player ...............................................11  
Using the MD Player (Listening to an MD)............13  
Recording onto an MD............................................15  
Using the MD Player (Editing) ...............................16  
Using External Equipments ...................................21  
1
Getting Started  
■  
Accessories  
Check that you have all of the following items, which are supplied with the System.  
Power Cord (1)  
AM Loop Antenna (1)  
Remote Control (1)  
Batteries (2)  
FM Wire Antenna (1)  
Speaker Cords (2)  
Polishing Cloth (1)  
If any of these items are missing, contact your dealer immediately.  
How To Put Batteries In the Remote Control  
Match the polarity (+ and –) on the batteries with the + and – markings in the battery compartment.  
R6P(SUM-3)/AA(15F)  
CAUTION: Handle batteries properly.  
To avoid battery leakage or explosion:  
Remove batteries when the Remote Control will not be used for a long time.  
When you need to replace the batteries, replace both batteries at the same time with new ones.  
Don’t use an old battery with a new one.  
Don’t use different types of batteries together.  
Using the Remote Control  
The Remote Control makes it easy to use many of the functions of the System from a distance of up to 7m (23 feet) away.  
You need to point the Remote Control at the remote sensor on the System’s front panel.  
STANDBY  
Remote sensor  
PHONES  
ULTRA MICRO COMPONENT SYSTEM  
UX-MD9000R  
2
CAUTION: Make all connections before plugging the System into an AC power outlet.  
Connecting the FM Antenna  
Using the Supplied Wire Antenna  
FM wire antenna (supplied)  
OPTICAL  
DIGITAL IN(AUX2)  
SUB WOOFER  
OUT  
R
L
Using the Coaxial Type Connector (Not Supplied)  
$ýæèðRKPýDQWHQQDýZLWKýFRD[LDOýW\SHýFRQQHFWRUýõ,(&ýRUý',1éèýêëèô  
VKRXOGýEHýFRQQHFWHGýWRýWKHý)0ýæèðRKPý&2$;,$/ýWHUPLQDOï  
AC IN  
,IýUHFHSWLRQýLVýSRRUñýFRQQHFWýWKHýRXWVLGHýDQWHQQDïý  
FM outdoor antenna  
(Not Supplied)  
Coaxial cable  
Note: Before attaching a 75 ohm coaxial lead (the kind with a  
round wire going to an outside antenna), disconnect the sup-  
plied FM Wire Antenna.  
CAUTION: To avoid noise, keep antennas away  
from the System, the connecting cord and the AC  
power cord.  
Connecting the AM (MW/LW) Antenna  
AM loop antenna (Supplied)  
OPTICAL  
SUB WOOFER  
DIGITAL IN(AUX2)  
OUT  
R
L
Attach the AM loop to its base by snapping the tabs on the  
loop into the slot in the base.  
AC IN  
75  
FM  
ANT  
AM EXT  
AM  
LOOP  
ANT  
Turn the loop until you have the best reception.  
3
CAUTION: Make all connections before plugging the System into an AC power outlet.  
Connecting the Speakers  
1. Open each of the terminals to connect the speaker wire leads.  
2. Connect the speaker cords between the Speaker terminals of the Unit and the terminals of the Speakers.  
Connect the cords with a black line to the (–) terminals and cords without a black line to the (+) terminals.  
3. Close each of the terminals to securely connect the cords.  
Right speaker (rear side)  
Left speaker (rear side)  
Marked with a black line  
SPEAKERS  
IMPEDANCE  
MIN 4  
L
R
Speakecord  
SPEAKER CORD  
CAUTION: A TV may display irregular colors if located near the speakers. If this happens, set the speak-  
ers away from the TV.  
Removing the speaker grilles  
The speaker grilles can be removed.  
When removing,  
Attaching the speaker grille  
1. Insert your fingers at the top and pull towards you.  
2. Also pull the bottom towards you.  
Speaker grille  
Connecting External Equipment  
Connecting a Tape Deck, etc.  
Connect (not supplied) signal cords between the System's LINE IN (AUX1)/OUT terminals and the output/input terminals of the external tape  
deck, etc.  
You can listen to one of these sources. Also, you can record the System's CD Player, MD Player, or tuner output signal to the external tape deck,  
etc..  
Signal cord (not supplied)  
Tape deck, etc. (not supplied)  
Pin-plug x 2  
Pin-plug x 2  
LINE IN  
(AUX1)  
LINE OUT  
Signal cord (Not supplied)  
R
L
Pin-plug x 2  
Pin-plug x 2  
4
CAUTION: Make all connections before plugging the System into an AC power outlet.  
Connecting Auxiliary Equipment  
Connect an (not supplied) signal cord between the LINE IN (AUX1) terminals on the System and the output terminals of your auxiliary equip-  
ment (e.g. turntable). You can listen to this source.  
Turntable (with built-in equalizer)  
Signal cord (not supplied)  
(not supplied)  
Pin-plug x 2  
Pin-plug x 2  
LINE IN  
(AUX1)  
LINE OUT  
R
L
Connecting a CD Player, etc (Digital Input (AUX2))  
Unplug the cap and connect an (not supplied) optical digital cord between the System's OPTICAL DIGITAL IN (AUX2) terminal and the output  
terminal of the CD player, etc.  
You can listen to the digital input signal from the CD player, etc.  
Cap  
CD player, etc. (not supplied)  
OPTICAL  
DIGITAL IN(AUX2)  
Optical digital cord (not supplied)  
Connecting a Subwoofer System  
Connect an (not supplied) signal cord between the SUB WOOFER OUT terminal and an external JVC subwoofer system, etc.  
Signal cord (not supplied)  
Subwoofer system (not supplied)  
SUB WOOFER  
OUT  
Connecting the AC Power Cord  
Firmly insert the supplied AC power cord into the AC inlet on the back of the Unit.  
AC IN  
Power cord  
CAUTIONS:  
ONLY USE THE JVC POWER CORD PROVIDED WITH THIS SYSTEM TO AVOID MALFUNCTION OR DAM-  
AGE TO THE SYSTEM.  
BE SURE TO UNPLUG THE POWER CORD FROM THE OUTLET WHEN GOING OUT OR WHEN THE SYS-  
TEM IS NOT IN USE FOR AN EXTENDED PERIOD OF TIME.  
Now you can plug the AC power cord into the wall outlet, and your System is at your command!!  
5
COMPU PLAY  
JVC's COMPU PLAY feature lets you control the most frequently used System functions with a single touch.  
With One Touch Operation you can play a CD, an MD, or turn on the radio with a single press of the play button for that function. One Touch  
Operation turns the power on for you, then starts the function you have specified. If the System is not ready (no CD in place, for example), the  
System still powers on so you can insert a CD.  
How One Touch Operation works in each case is explained in the section dealing with that function.  
The COMPU PLAY buttons are:  
On the Unit  
On the Remote Control  
CD 38button  
38  
CD  
button  
TUNER BAND button  
TUNER BAND button  
38  
38  
MD  
button  
MD  
button  
TAPE/AUX button  
TAPE/AUX button  
AUTOMATIC POWER ON  
The System automatically turns on with the following operation.  
When you press the CD 0button, the System automatically turns on and the CD holder opens to allow CD insertion. However, this opera-  
tion does not change the function to CD.  
When you press the  
button to turn off the System, the CD holder will automatically closed if it is opened.  
When you insert an MD, the System automatically turns on. However, this operation does not change the function to MD.  
Common Operations  
■  
REMOTE CONTROL RM-RXUMD9000R  
DIMMER SLEEP  
DIMMER  
CLOCK  
AHB SUPER  
CLOCK FM MODE TAPE/AUX  
AHB.  
AUTO  
SUPER PRO PRESET  
PROGRAM RANDOM REPEAT  
PRO  
BASS  
TREBLE  
CANCEL  
BASS  
TREBLE  
EDIT  
/TITLE  
DISPLAY  
/CHARA  
STANDBY  
STANDBY  
indicator  
UP  
TIMER/  
DISPLAY  
MODE  
SET  
SNOOZE  
<
>
PTY/EON  
DOWN  
MULTI CONTROL  
UP  
CLOCK  
CLOCK  
DOWN  
OPEN/CLOSE  
CD  
PTY/EON  
MD  
DISPLAY MODE  
CD  
TAPE  
/AUX  
MD  
TUNER  
BAND  
CD  
TUNER  
BAND  
EJECT  
MD  
CD SYNCHRO  
REC  
REC  
PAUSE  
VOLUME  
PHONES  
DOWN  
UP  
PHONES  
ULTRA MICRO COMPONENT SYSTEM  
UX-MD9000R  
VOLUME+,–  
VOLUME  
VOLUME UP, DOWN  
“Minidisc” indicator  
Some power (5W) is always consumed even though power is  
Turning the Power On and Off  
tTuornsewditocfhf (ocfafltlheed SSytasntedmbycMomopdlee)t.ely, unplug the AC power cord  
from the AC outlet. When you unplug the AC power cord, the  
clock will be reset to 0:00 after about 20 minutes, and preset Tuner  
stations will be erased after about 24 hours.  
Turning the System On ——————  
Press the  
button.  
The display comes on and the STANDBY indicator goes out.  
The System comes on ready to continue in the mode it was in when  
the power was last turned off.  
Adjusting the Brightness  
(DIMMER)  
STANDBY  
You can adjust the brightness of the display in three levels.  
To change the brightness, press the DIMMER button on the Re-  
mote Control.  
Each time you press the DIMMER button, the brightness changes as  
follows.  
Bright (Level 1)=Dark (Level 2)=Darker (Level 3)=(back to the be-  
For example, if the last thing you were doing was listening to a  
CD, you are now ready to listen to a CD again. If you wish, you  
cIfaynocuhwanegree ltiostaennointhgetrostohuerTceu.ner last, the Tuner comes on playing  
the station it was last set to.  
ginning)  
Turning the System Off ——————  
When the System is turned on, the display brightens with the  
Level 1.  
Press the  
button again.  
The "STANDBY" indicator lights up and the display is blank, except  
for the clock display.  
The “Minidisc” indicator will go out in Level 3.  
STANDBY  
6
The bass or treble level display goes out when the BASS or  
TREBLE button is pressed again or when nothing is done for  
about 6 seconds.  
Adjusting the Volume  
You can adjust the volume level between 0 and 50.  
The VOLUME indicator on the display indicates the volume level.  
Showing the Time (CLOCK)  
VOLUME  
Press the VOLUME UP button of the Unit to increase the volume or  
press the VOLUME DOWN button to decrease it.  
OR  
Press the VOLUME + button on the Remote Control to increase the  
volume or press the VOLUME - button to decrease it.  
In Standby mode, the clock appears on the display.  
When the System is turned on, you can display the clock at any time.  
To display the clock, press the CLOCK button.  
To light off the clock, press the CLOCK button again.  
CAUTION: DO NOT start playing any source with-  
out first setting the VOLUME control to minimum  
position, as a sudden blast of sound can damage  
your hearing, speakers and/or headphones.  
Note: To let work the clock, you need to set the clock beforehand.  
(See "Setting the Clock" on page 22.)  
For private listening  
Connect a pair of headphones to the PHONES jack. No sound  
comes out of the speakers.  
Be sure to turn down the volume before connecting or putting on  
headphones.  
Reinforcing the Bass Sound  
(AHB SUPER PRO)  
You can reinforce the bass sound to maintain rich, full bass at low  
volume (you can use this effect only for playback):  
To get the effect, press the AHB (Active Hyper Bass) SUPER  
PRO button on the Remote Control.  
The “BASS” indicator lights up on the display.  
To cancel the effect, press the button again.  
The “BASS” indicator goes out.  
Tone Control (BASS/TREBLE)  
You can control the tone by changing the bass and treble.  
BASS Control ———————————  
You can adjust the bass level (low frequency range level) between  
–6 and +6. (0: Flat)  
1.Press the BASS button on the Remote Con-  
trol.  
2.Press the UP or DOWN button on the  
Remote Control to adjust the bass level.  
BASS  
DOWN  
UP  
TREBLE Control ——————————  
You can adjust the treble level (high frequency range level) between  
–6 and +6. (0: Flat)  
1.Press the TREBLE button on the Remote  
Control.  
2.Press the UP or DOWN button on the  
Remote Control to adjust the treble level.  
TREBLE  
DOWN  
UP  
7
Using the Tuner  
■  
REMOTE CONTROL RM-RXUMD9000R  
DIMMER SLEEP  
PTY/EON  
DISPLAY MODE  
4
CLOCK FM MODE TAPE/AUX  
FM MODE  
AHB.  
AUTO  
SUPER PRO PRESET  
AUTO PRESET  
TIMER/  
SNOOZE  
DISPLAY  
MODE  
PROGRAM RANDOM REPEAT  
PTY/EON  
DOWN  
MULTI CONTROL  
UP  
CLOCK  
BASS  
TREBLE  
CANCEL  
¢
OPEN/CLOSE  
CD  
MD  
CD  
TAPE  
/AUX  
TUNER  
EDIT  
/TITLE  
DISPLAY  
/CHARA  
BAND  
SET  
EJECT  
MD  
CD SYNCHRO  
REC  
REC  
PAUSE  
VOLUME  
TUNER  
BAND  
UP  
UP  
DOWN  
UP  
SET  
<
>
<
>
DOWN  
PTY/EON  
DISPLAY MODE  
DOWN  
PTY/EON  
MD  
DISPLAY MODE  
CD  
Band display, Frequency display,  
Preset channel  
RDS  
indicators  
TUNER  
BAND  
TUNER BAND  
¢
4
VOLUME  
When the System is in use, the display  
shows other items as well.  
FM mode  
indicators  
For simplicity, we show here only the  
items described in this section.  
You can listen to FM and AM (MW/LW) stations. Stations can be  
tuned in manually, automatically, or from preset memory storage.  
Before listening to the radio:  
Example: For program number 12, press the > button, then  
press the UP button twice (or simply press the UP  
button 12 times.).  
Check that both the FM and AM (MW/LW) antennas are  
correctly connected. (See page 3).  
UP  
DOWN  
or  
(After 1 second)  
One Touch Radio —————————  
-XVWýSUHVVýWKHý781(5ý%$1'ýEXWWRQýWRýWXUQýRQýWKHý6\VWHPýDQGýVWDUW  
Presetting Stations  
You can preset up to 30 FM stations and up to 15 AM (MW/LW)  
stations using the Remote Control.  
SOD\LQJý<WKRHXýVýFWDDWQLRýVQZý\LWRFXKýýZIUHRUPHýýODDQV\WýýWRXWQKHHGUýýVWRRXï QGýVRXUFHýWRýWKHýUDGLRýE\ý  
SUHVVLQJýWKHý781(5ý%$1'ýEXWWRQï  
Note: Preset numbers may have been set to factory test frequen-  
cies prior to shipment. This is not a malfunction. You can  
preset the stations you want into memory by following one  
of the presetting methods below.  
Tuning In a Station  
1.Press the TUNER BAND button.  
The Band and Frequency you were last tuned to appear on the  
Manual Presetting—————————  
display.  
STORED  
Each time you press the button, the band alternates between FM  
P 1  
TUNER  
BAND  
and AM (MW/LW).  
SET  
SET  
UP  
DOWN  
or  
TUNER  
BAND  
AM  
FM  
FM=30,AM=15  
When changing the Band  
1.Select a band by pressing the TUNER  
2.Select a station using one of the following  
BAND button.  
methods.  
2.Press the 4 or ¢ button to tune in a sta-  
Manual Tuning  
tion.  
Press the 4or ¢button repeatedly to move from frequency  
to frequency until you find the station you want.  
OR  
3.Press the SET button.  
"P 1" will blink.  
Auto Tuning  
4.Press the UP, DOWN, > , or < button to  
If you press and hold the 4or ¢button for one second or  
more, the frequency changes down, or up, automatically until a  
station is found.  
select the preset number.  
UP button:  
Increases the preset number by 1.  
OR  
DOWN button: Decreases the preset number by 1.  
Preset Tuning using the Remote Control (Pos-  
sible only after presetting stations)  
Select the desired preset number using the UP, DOWN, >, and  
< buttons on the Remote Control. After 1 second the display  
will show the preset number's band and frequency.  
> button:  
< button:  
Increases the tenth digit for preset number.  
Decreases the tenth digit for preset number.  
5.Press the SET button.  
"STORED" appears and, after 1 second, the display returns to  
the broadcast frequency display.  
UP button:  
Increases the preset number by 1.  
DOWN button: Decreases the preset number by 1.  
6.Repeat above steps 1 to 5 for each station  
> button:  
< button:  
Increases the tenth digit for preset number.  
Decreases the tenth digit for preset number.  
you want to store in memory with a preset  
number.  
8
To cancel the presetting, press the CANCEL button in step  
3 or 4.  
To change the preset stations, repeat the same steps as  
above.  
To show the RDS signals on the  
display———————————————  
Press the DISPLAY MODE button while listening to an FM  
station.  
(DFKýWLPHý\RXýSUHVVýWKHýEXWWRQñýWKHýGLVSOD\ýFKDQJHVýWRýVKRZýLQIRUð  
PDWLRQýLQýWKHýIROORZLQJýRUGHUã  
Auto Presetting ——————————  
In each band, you can automatically preset FM-30, AM (MW/LW)-  
15 stations. Preset numbers will be allocated as stations are found,  
starting from the lowest station and moving up the frequency.  
DISPLAY  
MODE  
AUTO  
PRESET  
(for 2 seconds)  
TUNER  
BAND  
PS (Programme Service):  
:KLOHýVHDUFKLQJñý¦36§ýDSSHDUVñýWKHQýVWDWLRQýQDPHýLVýGLVSOD\HGïý¦12  
36§ýDSSHDUVýLIýQRýVLJQDOýLVýVHQWï  
PTY (Programme Type):  
1.Select a band by pressing the TUNER  
:KLOHýVHDUFKLQJñý¦37<§ýDSSHDUVñýWKHQýEURDGFDVWýSURJUDPPHýW\SHýLV  
GLVSOD\HGïý¦12ýý37<§ýDSSHDUVýLIýQRýVLJQDOýLVýVHQWï  
RT (Radio Text):  
:KLOHýVHDUFKLQJñý¦57§ýDSSHDUVñýWKHQýDýWH[WýPHVVDJHýVHQWýE\ýWKHýVWDð  
WLRQýLVýGLVSOD\HGïý¦12ý57§ýDSSHDUVýLIýQRýVLJQDOýLVýVHQWï  
Station Frequency:  
BAND button.  
2.Press the AUTO PRESET button on the  
Remote Control for more than two sec-  
onds.  
3.Repeat steps 1-2 for the other band.  
6WDWLRQýIUHTXHQF\ýõQRQð5'6ýVHUYLFHô  
If you want to change the preset stations, carry out the Manual  
Notes:  
Presetting for the desired preset numbers.  
,IýVHDUFKLQJýILQLVKHVýDWýRQFHñý¦36§ñý¦37<§ýDQGý¦57§ýZLOOýQRW  
DSSHDUýRQýWKHýGLVSOD\ï  
,Iý\RXýSUHVVýWKHý',63/$<ý02'(ýEXWWRQýZKLOHýOLVWHQLQJýWRýDQ  
$0ýõ0:î/:ôýVWDWLRQñýWKHýGLVSOD\ýRQO\ýVKRZVýVWDWLRQýIUHTXHQF\ï  
5'6ýLVýQRWýDYDLODEOHýIRUý$0ýõ0:î/:ôýEURDGFDVWVï  
CAUTION: If the System is unplugged or if a pow-  
er failure occurs, the preset stations will be  
erased after about 24 hours. If this happens, you  
will need to preset the stations again.  
On characters displayed  
:KHQýWKHýGLVSOD\ýVKRZVý36ñý37<ýRUý57ýVLJQDOVã  
7KHýGLVSOD\ýFDQQRWýVKRZýDFFHQWHGýOHWWHUVâý)RUýH[DPSOHñý¦  
PD\ýUHSUHVHQWýDFFHQWHGý¦$©V§ýOLNHý¦·ñýµñý ñýŸñýbýDQGýc§ï  
To Change the FM  
Reception Mode  
[Example]  
When you are tuned in an FM broadcast, the "STEREO" indicator  
lights up and you can hear stereo effects.  
If an FM stereo broadcast is hard to receive or noisy, you can select  
Monaural mode. Reception improves, but you lose any stereo effect.  
Press the FM MODE button on the Remote Control so that  
the "MONO" indicator lights up on the display.  
FM MODE  
STEREO  
MONO  
To restore the stereo effect, press the FM MODE button on the  
Remote Control so that the "MONO" indicator goes off.  
To search for a programme by PTY  
Receiving FM Stations with  
RDS  
<RXýFDQýXVHýWKHý5'6ýõ5DGLRý'DWDý6\VWHPôýE\ýXVLQJýWKHýEXWWRQVýRQ  
WKHý8QLWýRUýWKHý5HPRWHý&RQWUROï  
codes ————————————————  
2QHýRIýWKHýDGYDQWDJHVýRIýWKHý5'6ýVHUYLFHýLVýWKDWý\RXýFDQýORFDWHýD  
SDUWLFXODUýNLQGýRIýSURJUDPPHýE\ýVSHFLI\LQJýWKHý37<ýFRGHVï  
To search for a programme using PTY or TA codes:  
PTY/EON  
PTY/EON  
DOWN  
MULTI CONTROL  
UP  
5'6ýDOORZVý)0ýVWDWLRQVýWRýVHQGýDGGLWLRQDOýVLJQDOVýZLWKýWKHLUýUHJXODU  
SURJUDPPHý VLJQDOVïý )RUý H[DPSOHñý WKHý VWDWLRQVý VHQGý WKHLUý VWDWLRQ  
QDPHVñýDQGýLQIRUPDWLRQýDERXWýZKDWýW\SHýRIýSURJUDPPHVýWKH\ýEURDGð  
FDVWñýVXFKýDVýVSRUWVýRUýPXVLFñýHWFïý7KLVýXQLWýFDQýUHFHLYHýWKHýIROORZLQJ  
W\SHVýRIý5'6ýVLJQDOVã  
PS (Programme Service):  
VKRZVýFRPPRQO\ýNQRZQýVWDWLRQýQDPHVï  
PTY (Programme Type):  
1.Press the PTY/EON button once while lis-  
tening to an FM station.  
“SELECT PTY” appears on the display.  
VKRZVýW\SHVýRIýEURDGFDVWýSURJUDPPHVï  
RT (Radio Text):  
VKRZVýWH[WýPHVVDJHVýWKHýVWDWLRQýVHQGVï  
TA (Traffic Announcement):  
2.Select the PTY code using the 4 or ¢  
button (or UP or DOWN button on the  
Remote Control) within 10 seconds.  
(DFKýWLPHý\RXýSUHVVýWKHýEXWWRQñýWKHýGLVSOD\ýVKRZVýDýFDWHJRU\ýLQ  
WKHýIROORZLQJýRUGHUã  
VKRZVýWUDIILFýDQQRXQFHPHQWVýEHLQJýEURDGFDVWï  
What information can RDS signals provide?  
7KHýGLVSOD\ýVKRZVý5'6ýVLJQDOýLQIRUPDWLRQýWKDWýWKHýVWDWLRQýVHQGVï  
NEWSýAFFAIRSýINFO SPORTýEDUCATEý↔  
DRAMAýCULTUREýSCIENCEýVARIEDýPOP M  
9
ROCK MýM.O.R.MýLIGHT MýCLASSICSýOTH-  
ER MýWEATHERýFINANCEýCHILDRENýSO-  
CIAL Aý RELIGIONý PHONE INý TRAVELý ↔  
LEISUREýJAZZýCOUNTRYýNATIONALýOLD-  
IESýFOLK MýDOCUMENTýTRAFFICýNEWS  
To select a programme type ————  
PTY/EON  
PTY/EON  
DOWN  
MULTI CONTROL  
UP  
3.Press the PTY/EON button within 10 sec-  
1.Press the PTY/EON button twice while lis-  
onds again.  
tening to an FM station.  
:KLOHý VHDUFKLQJñý WKHý GLVSOD\ý DOWHUQDWHVý EHWZHHQý ¦6($5&+§  
DQGýWKHýVHOHFWHGý37<ýFRGHï  
ý¦6(/(&7ý(21§ýDSSHDUVýRQýWKHýGLVSOD\ï  
7KHýXQLWýVHDUFKHGýSUHVHWýVWDWLRQVýDQGýVWRSVýZKHQýLWýILQGVýDýVWDWLRQ  
RIýWKHýFDWHJRU\ý\RXýKDYHýVHOHFWHGñýWKHQýWXQHVýLQWRýWKDWýVWDWLRQï  
,IýQRýSURJUDPPHýLVýIRXQGñý¦127ý)281'§ýDSSHDUVýRQýWKHýGLVSOD\ï  
2.Select the programme type with the 4 or  
¢ button (or UP or DOWN button on the  
Remote Control) within 10 seconds.  
7KHýGLVSOD\ýVKRZVýDýSURJUDPPHýW\SHýLQýWKHýIROORZLQJýRUGHUã  
.
To continue searching after the first stop,  
SUHVVýWKHý37<ýEXWWRQýDJDLQýZKLOHýWKHýGLVSOD\ýLQGLFDWLRQVýEOLQNï  
To stop searching at any time during the process  
3UHVVýWKHý37<ýEXWWRQýWRýVWRSýVHDUFKýRSHUDWLRQï  
Note: Station will change from the current one.  
TA:  
NEWS: 1HZV  
INFO:ý 3URJUDPPHVýRQýPHGLFDOýVHUYLFHñýZHDWKHUýIRUHFDVWñýHWFï  
OFF:  
7UDIILFý$QQRXQFHPHQW  
Descriptions of the PTY Codes  
NEWS:ý  
1HZV  
(21ýRII  
AFFAIRS: 7RSLFDOýSURJUDPPHýH[SDQGLQJýRQýWKHýFXUUHQWýQHZVýRU  
DIIDLUV  
3.Press the PTY/EON button within 10 sec-  
INFO:  
3URJUDPPHVýRQýPHGLFDOýVHUYLFHñýZHDWKHUýIRUHFDVWVñ  
HWFï  
6SRUWVýHYHQWVý  
onds again to set the selected programme  
type.  
SPORT:ý  
7KHýVHOHFWHGýSURJUDPPHýW\SHýLQGLFDWRUýOLJKWVýXSýRQýWKHýGLVSOD\ñ  
DQGýWKHýXQLWýHQWHUVý(21ý6WDQGE\ýPRGHï  
EDUCATE: (GXFDWLRQDOýSURJUDPPHV  
DRAMA:ý 5DGLRýSOD\V  
CULTURE:ý 3URJUDPPHVýRQýQDWLRQDOýRUýUHJLRQDOýFXOWXUH  
SCIENCE: 3URJUDPPHVýRQýQDWXUDOýVFLHQFHVýDQGýWHFKQRORJ\  
7KHý(21ýLQGLFDWRUýOLJKWVýXSýZKHQýWXQHGýWRýDýVWDWLRQýZKLFKýSURð  
YLGHVý(21ýLQIRUPDWLRQï  
VARIED:  
POP M:  
2WKHUýSURJUDPPHVýOLNHýFRPHGLHVýRUýFHUHPRQLHV  
3RSýPXVLF  
If there is no station broadcasting the type of programme  
you have selected  
7KHý EURDGFDVWý VWDWLRQý EHLQJý FXUUHQWO\ý KHDUGý ZLOOý FRQWLQXHý WRý EH  
ROCK M:  
5RFNýPXVLF  
M.O.R.M:ý 0LGGOHðRIðWKHðURDGýPXVLFýõXVXDOO\ýFDOOHGý¦HDV\ýOLVð  
WHQLQJ§ô  
KHDUGï  
«
LIGHT M:ý /LJKWýPXVLF  
CLASSICS: &ODVVLFDOýPXVLF  
OTHER M: 2WKHUýPXVLF  
WEATHER:ý :HDWKHUýLQIRUPDWLRQ  
:KHQýDýVWDWLRQýVWDUWVýEURDGFDVWLQJýWKHýSURJUDPPHý\RXýKDYHýVHOHFWð  
HGñýWKLVýXQLWýDXWRPDWLFDOO\ýVZLWFKHVýWRýWKHýVWDWLRQïý7KHýSURJUDPPH  
W\SHýõ7$ñý1(:6ýRUý,1)2ôýLQGLFDWRUýVWDUWVýEOLQNLQJï  
«
FINANCE: 5HSRUWVýRQýFRPPHUFHñýWUDGLQJñýWKHý6WRFNý0DUNHWñýHWFï  
CHILDREN: (QWHUWDLQPHQWýSURJUDPPHVýIRUýFKLOGUHQ  
SOCIAL A: 3URJUDPPHVýRQýVRFLDOýDFWLYLWLHV  
RELIGION: 3URJUDPPHVý GHDOLQJý ZLWKý DQ\ý DVSHFWý RIý EHOLHIý RU  
IDLWKñýRUýWKHýQDWXUHýRIýH[LVWHQFHýRUýHWKLFV  
:KHQýWKHýSURJUDPPHýLVýRYHUñýWKLVýXQLWýJRHVýEDFNýWRýWKHýFXUUHQWO\ýVHð  
OHFWHGýVWDWLRQñýEXWýVWLOOýUHPDLQVýLQý(21ý6WDQGE\ýPRGHï  
Notes:  
,Iý WKHý (21ý LVý LQý VWDQGE\ý PRGHý DQGý WKHý IXQFWLRQý õ&'ñý 0'ñ  
7$3(î$8;ôýVZLWFKýLVýFKDQJHGýRUýWKHýSRZHUýLVýVZLWFKHGýRIIñ  
WKHQýWKHý(21ýPRGHýZLOOýEHýUHOHDVHGïý:KHQýWKHýEDQGýLVýVHWýWR  
$0ýõ0:î/:ôñýWKHý(21ýLVýQRWýDFWLYDWHGïý:KHQýWKHýEDQGýLVýVHW  
WRý)0ýDJDLQñýWKHý(21ýZLOOýEHýVHWýWRýVWDQGE\ýPRGHï  
PHONE IN: 3URJUDPPHVýZKHUHýSHRSOHýFDQýH[SUHVVýWKHLUýYLHZVýHLð  
WKHUýE\ýSKRQHýRUýLQýDýSXEOLFýIRUXP  
TRAVEL:  
3URJUDPPHVýDERXWýWUDYHOýGHVWLQDWLRQVñýSDFNDJHýWRXUVñ  
DQGýWUDYHOýLGHDVýDQGýRSSRUWXQLWLHV  
LEISURE: 3URJUDPPHVý FRQFHUQHGý ZLWKý UHFUHDWLRQDOý DFWLYLWLHV  
:KHQýWKHý(21ýLVýEHLQJýRSHUDWHGýõLïHïýWKHýVHOHFWHGýSURJUDPPH  
W\SHýLVýEHLQJýUHFHLYHGýIURPýWKHýEURDGFDVWýVWDWLRQôýDQGýLIýWKHý4ñ  
¢ýEXWWRQýLVýRSHUDWHGñýWKHýVWDWLRQýZLOOýQRWýVZLWFKýEDFNýWRýWKH  
FXUUHQWý VHOHFWHGý VWDWLRQý HYHQý DIWHUý WKHý SURJUDPPHý HQGVïý 7KH  
SURJUDPPHýW\SHýLQGLFDWRUýUHPDLQVýLQýWKHýGLVSOD\ñýLQGLFDWLQJýWKDW  
WKHý(21ýLVýLQýVWDQGE\ýPRGHï  
VXFKýDVýJDUGHQLQJñýFRRNLQJñýILVKLQJñýHWFï  
JAZZ:  
-D]]ýPXVLF  
COUNTRY: &RXQWU\ýPXVLF  
NATIONAL: &XUUHQWýSRSXODUýPXVLFýIURPýDQRWKHUýQDWLRQýUHJLRQñýLQ  
WKDWýFRXQWU\©VýODQJXDJH  
OLDIES:  
FOLK M:  
&ODVVLFýSRSýPXVLF  
)RONýPXVLF  
:KHQýWKHý(21ýLVýLQýVWDQGE\ýPRGHýDQGýDýUDGLRýEURDGFDVWýLVýEHð  
LQJýUHFRUGHGñýEHýFDUHIXOýEHFDXVHýWKHý(21ýPD\ýEHýDFWLYDWHGýDQG  
DýGLIIHUHQWýSURJUDPPHýWKDQýWKHýLQWHQGHGýRQHýPD\ýEHýUHFRUGHGï  
:KHQýWKHý(21ýPRGHýLVýQRWýUHTXLUHGñýUHOHDVHýWKHý(21ýPRGHï  
:KHQýWKHýDODUPýVLJQDOýLVýGHWHFWHGýE\ý(21ñýWKHýVWDWLRQýEURDGð  
FDVWLQJýWKHýDODUPýLVýUHFHLYHGýZLWKýSULRULW\ïý¦$/$50§ýLVýQRW  
GLVSOD\HGï  
DOCUMENT: 3URJUDPPHVýGHDOLQJýZLWKýIDFWXDOýPDWWHUVñýSUHVHQWHG  
LQýDQýLQYHVWLJDWLYHýVW\OH  
TRAFFIC: %URDGFDVWVýZKLFKýFDUU\ýWUDIILFýDQQRXQFHPHQWV  
To temporarily switch to a broadcast  
programme of your choice————  
(21ýõ(QKDQFHGý2WKHUý1HWZRUNVôýLVýDQRWKHUýFRQYHQLHQWý5'6ýVHUð  
YLFHýWKDWýDOORZVýWKLVýXQLWýWRýVZLWFKýWHPSRUDULO\ýWRýDýEURDGFDVWýSURð  
JUDPPHýRIý\RXUýFKRLFHýõ1(:6ñý7$ýRUý,1)2ôýIURPýWKHýFXUUHQWO\  
VHOHFWHGýVWDWLRQñýH[FHSWýLIý\RXýDUHýOLVWHQLQJýWRýDýQRQð5'6ýVWDWLRQýõDOO  
$0ýõ0:î/:ôýVWDWLRQVýRUýVRPHý)0ýVWDWLRQVôï  
Caution:  
When the sound alternated intermittently between  
the station tuned in by the EON function and the  
current selected station, cancel the EON mode.  
This does not constitute malfunction of the unit.  
,IýDQý)0ýVWDWLRQýGRHVýEURDGFDVWý(21ýLQIRUPDWLRQñý(21ýFDQQRWý  
EHýDFWLYDWHGï  
10  
Using the CD Player  
■  
L
REMOTE CONTROL RM-RXUMD9000R  
CD Holder  
DIMMER SLEEP  
CLOCK FM MODE TAPE/AUX  
4
AHB.  
AUTO  
SUPER PRO PRESET  
7
PROGRAM RANDOM REPEAT  
¢
PROGRAM  
REPEAT  
RANDOM  
TIMER/  
SNOOZE  
DISPLAY  
MODE  
BASS  
TREBLE  
CANCEL  
PTY/EON  
DOWN  
MULTI CONTROL  
UP  
CLOCK  
EDIT  
/TITLE  
DISPLAY  
/CHARA  
SET  
<
OPEN/CLOSE  
CD  
UP  
UP  
TAPE  
/AUX  
MD  
CD  
TUNER  
CD 0  
BAND  
EJECT  
MD  
CD SYNCHRO  
REC  
REC  
PAUSE  
SET  
VOLUME  
<
>
Track number, Playing time, Preset number  
>
DOWN  
UP  
DOWN  
DOWN  
CD 38  
PTY/EON  
MD  
DISPLAY MODE  
CD  
TUNER  
BAND  
CD 38  
4
¢
7
Repeat indicator  
VOLUME  
Play mode indicator  
Music calender  
When the System is in use, the display shows other items as well.  
For simplicity, we show here only the items described in this section.  
OVER indicator which lights up if the  
number of tracks of the CD exceeds 20.  
You can use Normal, Random, Program or Repeat Play. Repeat  
Play can repeat all the tracks or just one of the tracks on the CD.  
Here are the basic things you need to know to play a CD and locate  
the different tracks on it.  
Basics of Using the  
CD Player-Normal Play  
To Play a CD—————————————  
The Quickest Way To Start a CD Is With the One Touch  
Operation  
1. Insert a CD.  
Press the CD38button.  
2. Press the CD 38 button.  
The power is automatically turned on. If a CD is already  
inserted, it will start playing from the first track.  
If no CD is inserted, "NO DISC" appears on the display and the  
CD Player remains in Stop mode.  
The first track of the CD begins playing.  
Track number  
Playback time  
The track number that has been played disappears from the  
music calender.  
The CD Player automatically stops when the last track of the  
CD has finished playing.  
To Insert a CD  
1.Press the CD 0 button on the Unit.  
To stop playing the CD, press the 7button.  
The following information for the CD is displayed.  
The CD holder opens.  
2.Place a CD, with its label side up as shown  
below.  
Total track number  
Total playback time  
To stop playing and remove the CD, press the CD0button to  
open the CD holder.  
To pause, press the CD38 button. The playback time blinks on  
the display.  
To cancel pause, press the same button again. Play continues  
from the point where it was paused.  
STANDBY  
To Select a Track or Passage within  
a Track ———————————————  
During playback, press the 4or ¢button to select the track you  
want.  
3.Press the CD 0 button again to close the  
CD holder.  
The selected track starts playing.  
To close the CD holder and play the CD, you can press the CD 38  
3UHVVýWKHý¢ýEXWWRQýRQFHýWRýVNLSýWRýWKHýEHJLQQLQJýRIýWKHý  
QH[WýWUDFNï  
3UHVVýWKHý4ýEXWWRQýWRýVNLSýWRýWKHýEHJLQQLQJýRIýWKHýWUDFNýEHð  
LQJýSOD\HGïý3UHVVýWZLFHýTXLFNO\ýWRýVNLSýWRýWKHýEHJLQQLQJýRIý  
WKHýSUHYLRXVýWUDFNï  
bYuottuonc.an place an 8 cm (3'') CD without an adaptor.  
If the CD cannot be read correctly (because it is scratched, for  
eYxoaumcpalne)i,n"se0rt0a:0C0"Dawppheilaersliostnenthinegditsoptlhaey.other source.  
Search Play —————————————  
Holding down the 4or ¢button, during playback, will fast for-  
ward/backwards the CD so you can quickly find a particular pas-  
sage in the track you are listening to.  
11  
To Modify the Program ———————  
Modify the contents of the program while the CD Player is stopped.  
Each time you press the 7button, the last track in the program is de-  
leted. To add new tracks to the end of the program, repeat above  
steps 5 to 7.  
Programming the  
Playing Order of the Tracks  
You can program the playing order of the tracks using the Remote  
Control.  
You can program up to 20 tracks in any desired order including  
Ythoeusacmaneotrnalcykms.ake a program when the CD Player is stopped.  
Random Play  
The tracks will play in no special order when you use this mode.  
1. Insert a CD.  
1. Press the RANDOM button on the Remote  
2. Press the CD 38 button.  
Control.  
3. Press the 7 button to stop the CD.  
The "CD RANDOM" indicator lights up on the display.  
4.Press the PROGRAM button.  
38  
2.Press the CD  
button.  
The System enters the programming mode and the “CD PRO-  
The tracks are played in random order.  
GRAM” indicator lights up.  
To skip a track during playback, press the ¢button to jump  
to the next track in the random sequence. Press the 4 button to  
jump back to the start of a track being played.  
PROGRAM  
To exit Random Play mode, press the RANDOM button to light  
off the "CD RANDOM" indicator and carry out Normal Play or  
Program Play, or press the CD0button to open the CD holder.  
5.Press the UP, DOWN, >, or < button to  
select the track to program.  
UP button:  
Increases the track number by 1.  
DOWN button: Decreases the track number by 1.  
Repeating Tracks  
You can set the program or individual track playing to repeat as  
many times as you like.  
> button:  
< button:  
Increases the tenth digit of the track number.  
Decreases the tenth digit of the track number.  
Example: for track 2, press the UP button twice. For track 12,  
press the > button, then press the UP button twice (or simply  
press the UP button 12 times).  
Press the REPEAT button on the Remote Control.  
The Repeat indicator changes with each press of the button, as  
shown below.  
6.Press the SET button.  
Program order number  
=
ALL =blank display =(back to the beginning)  
UP  
: Repeats one track.  
(After 2 seconds)  
ALL : In Normal Play mode, repeats all the tracks.  
In Program Play mode, repeats all the tracks in the  
program.  
SET  
DOWN  
In Random Play mode, repeats all the tracks in ran-  
dom order.  
Total playback time of the programmed tracks  
To exit Repeat mode, press the REPEAT button until the Repeat  
indicator on the display goes out.  
7.Repeat steps 5 and 6 to select the other  
tracks for the program.  
In Random Play, as a matter of course,  
cannot be selected.  
Repeat mode remains on the display even when you change the  
You can see the total playback time of programmed tracks on  
the display. Also, you can see the programmed tracks on the  
music calender.  
play mode.  
38  
8.Press the CD  
button.  
The System plays the tracks in the order you have programmed  
tYhoemu c. an skip to a particular program track by pressing the 4  
or ¢button during Program Play.  
To stop playing, press the 7button once.  
To confirm the programmed tracks while the CD player is  
stopped, press the 4 or ¢ button; the tracks making up the  
program will successively be displayed in the programmed order.  
To delete all the tracks in the program, press the 7button re-  
peatedly until all the tracks are cleared. Turning off the power or  
pressing the CD 0button to open the CD holder will also clear the  
programmed tracks.  
To exit the program mode once, while the CD Player is  
stopped, press the PROGRAM button to light off the "CD PRO-  
GRAM" indicator.  
Note: If the total playback time of the programmed tracks exceeds  
99 minutes 59 seconds, the total playback time will go out  
on the display.  
12  
(Listening to an MD)  
Using the MD Player  
■  
REMOTE CONTROL RM-RXUMD9000R  
DIMMER SLEEP  
4
CLOCK FM MODE TAPE/AUX  
7
¢
AHB.  
AUTO  
SUPER PRO PRESET  
TIMER/  
PROGRAM RANDOM REPEAT  
DISPLAY  
MODE  
SNOOZE  
PTY/EON  
DOWN  
MULTI CONTROL  
UP  
CLOCK  
REPEAT  
PROGRAM  
RANDOM  
BASS  
TREBLE  
CANCEL  
MD 38  
OPEN/CLOSE  
CD  
Track number, Playing time, Preset number  
CANCEL  
UP  
MD  
CD  
TAPE  
/AUX  
TUNER  
BAND  
EDIT  
/TITLE  
DISPLAY  
/CHARA  
SET  
<
EJECT  
MD  
CD SYNCHRO  
REC  
REC  
PAUSE  
DISPLAY  
VOLUME  
UP  
MD 0  
DOWN  
UP  
/CHARA  
SET  
<
>
>
DOWN  
DOWN  
PTY/EON  
MD  
DISPLAY MODE  
CD  
TUNER  
BAND  
MD 38  
Repeat indicator  
¢
7
4
Play mode indicator  
Music calender  
VOLUME  
When the System is in use, the display shows other items as well.  
For simplicity, we show here only the items described in this sec-  
tion.  
OVER indicator which lights up if the number  
of tracks of the MD exceeds 20.  
You can use Normal, Random, Program or Repeat Play in the same  
way as for CD Player. Repeat Play can repeat all the tracks or just  
one of the tracks on the MD.  
The tracks in the MD appear on the music calender.  
The track number that has been played disappears from the  
music calender.  
Here are the basic things you need to know to play an MD and locate  
the different tracks on it.  
The MD Player automatically stops when the last track of the  
MD has finished playing.  
If the MD has the disc title, the disc title is displayed before  
The Quickest Way To Start an MD Is With the One Touch  
Operation  
pIflathyeintgratchke hfiarsstthtreactiktl.e, the track title will be displayed before  
Press the MD38button.  
playing the track.  
You can give the disc title and the track title as required. (See  
page 19.)  
The power is automatically turned on. If an MD is already  
inserted, it will start playing from the first track.  
If no MD is inserted, "NO DISC" appears on the display and  
the MD Player remains in Stop mode.  
To stop playing the MD, press the 7 button. The following in-  
formation for the MD is displayed.  
To Insert an MD  
Total track number Total playback time  
To stop playing and remove the MD, press the MD0 button  
to eject the MD.  
To pause, press the MD 38button. The playback time blinks on  
the display.  
Insert an MD into the MD slot.  
Insert it with its label side up and the #or ] mark of the MD  
directs as shown in the figure.  
The MD is automatically drawn inside the MD Player and the  
red MD indicator on the front of the Unit lights up.  
To cancel pause, press the same button again. Play continues  
from the point where it was paused.  
MD indicator  
MD slot  
MD  
Displaying the Disc Title ——————  
You can display the disc title of the MD during Stop mode. If the  
disc title is not given yet, “NO TITLE” appears.  
During Stop mode, press the DISPLAY/CHARA button on  
the Remote Control.  
Each time you press the button, the display changes as follow.  
You can insert an MD while listening to the other source.  
Basics of Using the  
MD Player - Normal Play  
Total track number and total playback time=Disc title=Remaining  
time (recordable capacity) of MD (e.g. REM. 23:00)=(back to the  
beginning)  
To Play an MD ———————————  
To Select a Track or Passage within  
a Track ———————————————  
During playback, press the 4or ¢button to select the track you  
want.  
1. Insert an MD.  
The MD indicator lights up.  
The selected track starts playing.  
2. Press the MD 38 button.  
3UHVVýWKHý¢ýEXWWRQýRQFHýWRýVNLSýWRýWKHýEHJLQQLQJýRIýWKHý  
QH[WýWUDFNï  
3UHVVýWKHý4ýEXWWRQýWRýVNLSýWRýWKHýEHJLQQLQJýRIýWKHýWUDFNýEHð  
LQJýSOD\HGïý3UHVVýWZLFHýTXLFNO\ýWRýVNLSýWRýWKHýEHJLQQLQJýRIý  
WKHýSUHYLRXVýWUDFNï  
The first track of the MD begins playing. (The MD indicator  
stays lit.)  
Track number  
Playback time  
13  
Note: If the total playback time of the programmed tracks exceeds  
150 minutes, the total playback time will go out on the dis-  
play.  
Search Play ————————————  
Holding down the 4or ¢button, during playback, will fast for-  
ward/backwards the MD so you can quickly find a particular pas-  
sage in the track you are listening to.  
To Modify the Program ———————  
Modify the contents of the program while the MD Player is stopped.  
Each time you press the 7button, the last track in the program is de-  
leted. To add new tracks to the end of the program, repeat above  
steps 5 to 7.  
Programming the  
Playing Order of the Tracks  
You can program the playing order of the tracks using the Remote  
Control.  
Random Play  
The tracks will play in no special order when you use this mode.  
You can program up to 32 tracks in any desired order including  
Ythoeusacmaneotrnalcykms.ake a program when the MD Player is stopped.  
1. Press the RANDOM button on the Remote  
1. Insert an MD.  
Control.  
2. Press the MD 38 button.  
The "MD RANDOM" indicator lights up on the display.  
3. Press the 7 button to stop the MD.  
2.Press the MD 38 button.  
The tracks are played in random order.  
4. Press the PROGRAM button.  
To skip a track during playback, press the ¢button to jump  
to the next track in the random sequence. Press the 4 button to  
jump back to the start of a track being played.  
The System enters the programming mode and the "MD PRO-  
GRAM" indicator lights up.  
PROGRAM  
To exit Random Play mode, press the RANDOM button to light  
off the “MD RANDOM” indicator and carry out Normal Play or  
Program Play, or press the MD 0button to eject the MD.  
5.Press the UP, DOWN, >, or < button to  
Repeating Tracks  
You can set the program or individual track playing to repeat as  
many times as you like.  
select the track to program.  
UP button:  
Increases the track number by 1.  
DOWN button: Decreases the track number by 1.  
> button:  
< button:  
Increases the tenth digit of the track number.  
Decreases the tenth digit of the track number.  
Press the REPEAT button on the Remote Control.  
The Repeat indicator changes with each press of the button, as  
shown below.  
Example: for track 2, press the UP button twice. For track 12,  
press the > button, then press the UP button twice (or simply  
press the UP button 12 times).  
=
ALL=blank display =(back to the beginning)  
: Repeats one track.  
6.Press the SET button.  
ALL : In Normal Play mode, repeats all the tracks.  
In Program Play mode, repeats all the tracks in the  
program.  
Program order number  
(After 2 seconds)  
UP  
In Random Play mode, repeats all the tracks in ran-  
dom order.  
SET  
DOWN  
To exit Repeat mode, press the REPEAT button until the Repeat  
indicator on the display goes out.  
Total playback time of the  
programmed tracks  
In Random Play, as a matter of course,  
cannot be selected.  
Repeat mode remains on the display even when you change the  
7.Repeat steps 5 and 6 to select the other  
play mode.  
tracks for the program.  
You can see the total playback time of programmed tracks on  
the display. Also, you can see the programmed tracks on the  
music calender.  
8.Press the MD 38 button.  
The System plays the tracks in the order you have programmed  
tYhoemu c. an skip to a particular program track by pressing the 4  
oTro¢stopbpultatoynindgu, rpirnegssPtrhoegr7ambuPttloany..  
To confirm the programmed tracks while the MD Player is  
stopped, press the 4 or ¢ button; the tracks making up the  
program will successively be displayed in the programmed order.  
To delete all the tracks in the program, press the 7button re-  
peatedly until all the tracks are cleared. Turning off the power or  
pressing the MD 0 button to eject the MD will also clear the pro-  
grammed tracks.  
To exit the program mode once, while the MD Player is  
stopped, press the PROGRAM button to light off the "MD PRO-  
GRAM" indicator.  
14  
Recording onto an MD  
■  
REMOTE CONTROL RM-RXUMD9000R  
DIMMER SLEEP  
CLOCK FM MODE TAPE/AUX  
AHB.  
AUTO  
SUPER PRO PRESET  
/8  
7
TIMER/  
SNOOZE  
DISPLAY  
MODE  
PROGRAM RANDOM REPEAT  
PTY/EON  
DOWN  
MULTI CONTROL  
UP  
CLOCK  
Track number, Playing time, Preset number  
MD 38  
BASS  
TREBLE  
CANCEL  
OPEN/CLOSE  
CD  
TAPE  
/AUX  
MD  
TUNER  
BAND  
CD  
EDIT  
/TITLE  
DISPLAY  
/CHARA  
EJECT  
MD  
CD SYNCHRO  
REC  
REC  
PAUSE  
VOLUME  
DISPLAY  
/ CHARA  
UP  
MD 0  
DOWN  
UP  
SET  
<
>
DOWN  
PTY/EON  
MD  
DISPLAY MODE  
CD  
TUNER  
BAND  
REC PAUSE  
CD SYNCHRO REC  
MD 38  
7
Music calender  
VOLUME  
When the System is in use, the display shows other items as well.  
For simplicity, we show here only the items described in this section.  
OVER indicator which lights up if the  
number of tracks of the MD exceeds 20.  
Recording onto an MD from any of the sound sources is simple. Just  
insert an MD to the Unit, have the source ready, make one or two  
settings, and you are ready to record. For each source, the procedure  
is a little bit different so we explain each separately. But first, here  
are a few things to make your recordings better.  
(See "Checking the Remaining Time of the MD" mentioned on  
page 16.)  
Indication of the MD Indicator for  
Recording ——————————————  
The MD indicator on the front panel of the Unit blinks as follow.  
Things To Know Before You Start  
Record-pause mode:  
During recording:  
MD inserted or played: Stays lit.  
Blinks rapidly.  
Blinks slowly.  
Recording —————————————  
It may be unlawful to record or play back copyrighted  
mCaarteefruialllywrietahdouthtetheRcuolenssoenf Dt oigfitthaleDcuobpbyirnigghtoonwpnaegre.  
Standard Recording  
You can record any sound source to an MD as follows.  
2T5h.e MD Recorder supports the following sampling frequencies  
for digital sources.  
For the OPTICAL DIGITAL IN (AUX2): 32 kHz, 44.1 kHz and  
48 kHz.  
1. Insert a MD with its label side up.  
The MD indicator lights up.  
FTohretrheecoCrDdinPglalyeevrelo,fwthheicUhnisitt:h4e4v.1olkuHmze.at which the new MD  
is being made, is automatically set correctly, so it is not affected  
by the VOLUME level of the System. Nor it is affected by ad-  
justing the sound effects. Thus, during recording you can adjust  
the sound you are actually listening to without affecting the re-  
cTohredaincgcildeevnetla.l erasure prevention knob is provided on the back  
of an MD cartridge to prevent accidental erasure or recording.  
It must be set to the close position beforehand.  
2. Prepare one of the sources.  
CD: Use the "CD Synchro Recording" mentioned below.  
Tuner: Tune in to a station.  
AUX1 (LINE IN (AUX1)): Press the TAPE/AUX button on the  
Unit or the Remote Control until “AUX 1 ANALOG IN” ap-  
pears on the display.  
AUX2 (OPTICAL DIGITAL IN (AUX2)): Press the TAPE/  
AUX button on the Unit or the Remote Control until “AUX 2  
DIGITAL IN” appears on the display.  
Accidental erasure prevention knob  
3. Press the REC PAUSE button on the Unit or  
the /8 button on the Remote Control.  
The MD indicator starts blinking and the track number in the  
music calender is increased by 1.  
Open  
Close  
4.Play the record source selected in step 2.  
When you stick an adhesive label onto the MD cartridge, adhere  
5.Press the MD 38 button to start recording.  
it securely. If it peels off, ejection trouble, etc. will occur.  
The MD indicator blinks slowly and the selected source is re-  
corded on the MD.  
Preparation Before Recording ———  
Be sure that the MD is not the Play-only type one.  
REC  
PAUSE  
MD  
or  
(Source playback)  
Be sure that the accidental erasure prevention knob of the MD  
cartridge is set to the close position. Otherwise, "DISC PRO-  
TECTED" will appear when you try to record a signal to the  
(Track is increased by 1.)  
MBeDs.ure that the MD has enough space for recording. If not, car-  
ry out ALL ERASE or ERASE function to erase all the tracks  
or desired tracks in the MD. (See page 18-19.) You can check  
the recordable remaining time of the MD in Stop mode or dur-  
ing recording by pressing the DISPLAY/CHARA button.  
6.Press the 7 button to stop recording.  
The MD indicator stays lit and "UTOCwriting" appears on the  
display, indicating that the recording is successfully completed.  
Then, the MD stops.  
15  
If the MD becomes full before pressing the 7button, the  
recording will be terminated after indicating “UTOCwriting”.  
2.Insert a CD. (See page 11.)  
3.Press the CD 38 button and then press the  
7 button to stop the CD.  
Checking the Remaining Time of  
the MD ———————————————  
You can see the recordable remaining time of the MD in Stop or Re-  
cording mode.  
4. Press the CD SYNCHRO REC button on the  
Unit.  
Digital recording from the CD to the MD starts.  
The track number for the MD increases synchronous with the  
track on the CD.  
After the CD Player has played the entire CD or all the pro-  
grammed tracks, "UTOCwriting" appears on the display, indi-  
cating that the recording is successfully completed. Then, the  
MD and the CD stops.  
Press the DISPLAY/CHARA button on the Remote Control,  
the remaining time appears on the display.  
Track marking ———————————  
Whenever playback advances from one track to another during  
digital recording, the track number at the MD side is automati-  
cally incremented by 1.  
Whenever no sound at the playback side continues for 3 or  
more seconds during analog recording, the track number at the  
MD side is automatically incremented by 1.  
The track number at the MD side is automatically incremented  
by 1 by pressing the SET button on the remote control at the  
desirable location during analog recording. (tuner or the equip-  
ment connected to the AUX-1.).  
When the MD becomes full before the CD Player finishes play-  
back, the MD stops after indicating "UTOCwriting".  
One Track Recording ————————  
1. Insert an MD with its label side up.  
2. Play the track on the CD you wish to  
record.  
CD Synchro Recording  
Everything on the CD goes onto the MD in the order it is on the CD,  
or according to the order you have set in the program. (See page 12  
for programming the CD tracks.)  
3. Press the CD SYNCHRO REC button on the  
Unit.  
The CD Player returns to the beginning of that track and the  
track is recorded on the MD. After recording, the CD Player and  
MD Player automatically stop.  
1. Insert an MD with its label side up.  
Using the MD Player (Editing)  
■  
In addition to its recording and play functions, the MD Player comes with editing functions. You can divide, join, move, or erase the recorded  
tracks in the MD as required. Also, you can give a disc title to the MD and track titles to the tracks in the MD.  
Dividing tracks (DIVIDE function)  
This involves adding a track mark (see Note) at some point during  
the track which is to be made into the start of an additional track so  
that the original track is divided into two tracks.  
Track No.  
Moving tracks (MOVE function)  
Tracks can be moved around so that they are in the desired se-  
quence.  
Track No.  
Track A Track B Track C Track D  
Track A Track B Track C Track D  
MOVE  
DIVIDE  
Track A Track C Track D Track B  
Track A Track B Track C Track D  
Erasing tracks (ERASE function)  
This enables unnecessary tracks. Narration, etc. to be erased speed-  
ily. The erased parts do not remain as silences but are closed up by  
the subsequent tracks.  
Joining tracks (JOIN function)  
This involves erasing a track mark and turning two adjoining tracks  
into one track.  
Track No.  
Track No.  
Track A Track B Track C Track D  
Track A Track B. Track C Track D  
Erasing  
JOIN  
Track B  
Track A + Track B. Track C Track D  
Newtrackscan  
be recorded.  
Track A Track C Track D  
16  
Erasing all the tracks (ALL ERASE  
Giving titles to discs and tracks  
function)  
(TITLE function)  
All the tracks can be erased at once without recording fresh material  
over them.  
A title consisting of up to 32 characters can be given to a disc and a  
track. The title given appears in the display window.  
Track No.  
Track A Track B Track C Track D  
ALL  
ERASE  
New tracks can be recorded.  
Note: Track marks  
These marks are provided to locate the start of each track. Whatever  
lies between one track mark and the next is considered to a track.  
and the numbers of the tracks (called “track numbers”) are dis-  
played in the sequence in which they are to be played.  
Track number, Playing time, Preset number  
REMOTE CONTROL RM-RXUMD9000R  
DIMMER  
SLEEP  
CLOCK FM MODE TAPE/AUX  
AHB.  
AUTO  
SUPER PRO PRESET  
/8  
PROGRAM RANDOM REPEAT  
UP  
SET  
BASS  
TREBLE  
CANCEL  
CANCEL  
EDIT  
/TITLE  
DISPLAY  
/CHARA  
UP  
DISPLAY/CHARA  
EDIT/TITLE  
<
SET  
<
>
>
DOWN  
DOWN  
PTY/EON  
MD  
DISPLAY MODE  
CD  
Music calender  
TUNER  
BAND  
MD 38  
¢
7
4
OVER indicator which lights up if the  
number of tracks of the MD exceeds 20.  
VOLUME  
Example: for track 2, press the UP button twice. For track  
12, use the > button to rapidly increase the track number (or  
simply press the UP button 12 times.)  
Dividing Tracks  
(DIVIDE Function)  
Use the Remote Control to carry out this function.  
6. Press the SET button at the point where  
the track is to be divided.  
1.Insert an MD to be edited with its label side  
SET  
up.  
2.Press the MD 38 button and then 7 button  
The selected track is divided into two tracks and the track  
number in the music calender will increase by 1.  
The recording lasting for 4 seconds starting where the track  
was divided is repeatedly played for your reference.  
Movement is possible within the POSITION-128 to 128 range  
(about 8 seconds before or after the position). The recording  
lasting for 4 seconds starting from the position to which the di-  
viding point has been moved is repeatedly played.  
to set the function to MD.  
The track numbers and total playback time are displayed.  
3.Press the EDIT/TITLE button until "DIVIDE  
?" is displayed.  
The "EDIT" indicator appears on the display.  
DIVIDE=JOIN=MOVE=ERASE=ALL ERASE=DISC  
TITLE=TITLE =(Back to the beginning)  
7. Press the SET button.  
4.Press the SET button.  
Alternates  
Playback time of the track  
SET  
EDIT  
/TITLE  
SET  
8. Press the EDIT/TITLE button.  
Track to be divided  
The “EDIT” indicator disappears on the display.  
5.Select the track number to be divided.  
9. Press the MD 0 button to complete editing.  
The selected track is automatically played.  
To select the track number, press the UP, DOWN, >, or < but-  
ton.  
The MD is ejected after "UTOCwriting" is displayed.  
You can also complete editing operation by pressing the  
button to turn off the power.  
UP button:  
Increases the track number by 1.  
To cancel the operation, press the CANCEL button in step 4, 5,  
or 7 until the display returns to the original display before editing  
the track.  
DOWN button: Decreases the track number by 1.  
> button:  
< button:  
Rapidly increases the track number.  
Rapidly decreases the track number.  
17  
Note: While “UTOCwriting” is displayed, do not disconnect the  
power cord or subject the Unit to the vibration to avoid in-  
correct recording.  
3.Press the EDIT/TITLE button until "MOVE ?"  
is displayed.  
The "EDIT" indicator appears on the display.  
DIVIDE=JOIN=MOVE=ERASE=ALL ERASE=DISC  
TITLE=TITLE=(Back to the beginning)  
Joining Tracks  
(JOIN Function)  
Use the Remote Control to carry out this function.  
4.Press the SET button.  
Track to be moved  
EDIT  
/TITLE  
1. Insert an MD to be edited with its label side up.  
SET  
2.Press the MD 38 button and then 7 button  
to set the function to MD.  
The track numbers and total playback time are displayed.  
5.Select the track number to be moved.  
3.Press the EDIT/TITLE button until "JOIN ?"  
To select the track number, press the UP, DOWN, >, or < but-  
ton. (For details, see step 5 in “Dividing Tracks (DIVIDE Func-  
tion)”.)  
is displayed.  
The "EDIT" indicator appears on the display.  
Example: Track number 12.  
DIVIDE=JOIN=MOVE=ERASE=ALL ERASE=DISC  
TITLE=TITLE=(Back to the beginning)  
4.Press the SET button.  
EDIT  
/TITLE  
6.Press the SET button.  
SET  
5.Select the track number to be joined.  
7.Select the destination to which the track is  
To select the track number, press the UP, DOWN, >, or < button.  
(For details, see step 5 in “Dividing Tracks (DIVIDE Function)”.)  
Example: Track number 2.  
to be moved.  
To select the track number, press the UP, DOWN, >, or < but-  
ton.  
In this example, the 12th track will move to the 14th track.  
(Since, the 12th track is lost, the upper tracks than the 12th one  
will be shifted toward the younger tracks.)  
Track to be joined  
Selected track  
Destination track  
Track to be moved  
6.Press the SET button.  
Alternates  
SET  
8.Press the SET button.  
Alternates  
SET  
7.Press the EDIT/TITLE button.  
The selected track and the previous track are joined and the  
track numbers in the music calender will decrease by 1.  
Then the “EDIT” indicator disappears on the display.  
9.Press the EDIT/TITLE button.  
The “EDIT” indicator disappears on the display.  
8.Press the MD0 button to complete editing.  
The MD is ejected after “UTOCwriting” is displayed.  
10.  
Press the MD0 button to complete editing.  
The MD is ejected after "UTOCwriting" is displayed.  
You can also complete editing operation by pressing the  
button to turn off the power.  
You can also complete editing operation by pressing the  
button to turn off the power.  
To cancel the operation, press the CANCEL button in step 4, 5,  
or 6 until the display returns to the original display before editing  
the track.  
Note: While "UTOCwriting" is displayed, do not disconnect the  
power cord or subject the Unit to the vibration to avoid in-  
correct recording.  
To cancel the operation, press the CANCEL button in step 4  
through 8 until the display returns to the original display before ed-  
iting the track.  
Note: While "UTOCwriting" is displayed, do not disconnect the  
power cord or subject the Unit to the vibration to avoid in-  
correct recording.  
Moving Tracks  
(MOVE Function)  
Use the Remote Control to carry out this function.  
Erasing Tracks  
(ERASE Function)  
1.Insert an MD to be edited with its label side  
Use the Remote Control to carry out this function.  
up.  
1.Insert an MD to be edited with its label side  
2.Press the MD 38 button and then 7 button  
up.  
to set the function to MD.  
The track numbers and total playback time are displayed.  
18  
2.Press the MD 38 button and then 7 button  
5.Press the EDIT/TITLE button.  
to set the function to MD.  
All the tracks in the MD are erased and “BLANK DISC” is kept  
The track numbers and total playback time are displayed.  
displayed.  
The "EDIT" indicator disappears on the display.  
To cancel the all erasing, press the CANCEL button in step 4.  
To remove the MD, press the MD0button.  
Note: While “UTOCwriting” is displayed, do not disconnect the  
power cord or subject the Unit to the vibration to avoid in-  
correct recording.  
3.Press the EDIT/TITLE button until "ERASE  
?" is displayed.  
The "EDIT" indicator appears on the display.  
DIVIDE=JOIN=MOVE=ERASE =ALL ERASE=DISC  
TITLE=TITLE=(Back to the beginning)  
4.Press the SET button.  
Track to be erased  
Giving Titles to MD (DISC TI-  
TLE/TITLE Function)  
You can give a disc title to the MD and a track title to the tracks in  
the MD. Any title name can be given up to 32 characters using the  
provided character sets.  
5.Select the track number to be erased.  
To select the track number, press the UP, DOWN, >, or < but-  
ton. (For details, see step 5 in "Dividing Tracks (DIVIDE Func-  
tion)".)  
The disc title you have given will be displayed in the following cases.  
When you insert the MD while the function is set to MD.  
When you press the MD38button and then 7button to set the  
function to MD.  
6.Press the SET button.  
Alternates  
Once you have given the title to the tracks, the track title will be dis-  
played before playing the track.  
SET  
Since the procedure to give title is the same as for the disc title  
and track title except for step 4, both functions are explained to-  
7.Press the EDIT/TITLE button.  
gUestehethreheRreem. ote Control to carry out these functions.  
The selected track is erased and the track numbers in the music  
calender decreases by 1.  
Then the “EDIT” indicator disappears on the display.  
1.Insert an MD to be edited with its label side  
up.  
8.Press the MD 0 button to complete editing.  
The MD is ejected after “UTOCwriting” is displayed.  
2.Press the MD 38 button and then 7 button  
You can also complete editing operation by pressing  
the button to turn off the power.  
to set the function to MD.  
The total track numbers and total playback time are displayed.  
To cancel the operation, press the CANCEL button in step 4, 5,  
or 6 until the display returns to the original display before editing  
the track.  
Note: While “UTOCwriting” is displayed, do not disconnect the  
power cord or subject the Unit to the vibration to avoid in-  
correct recording.  
3.Press the EDIT/TITLE button until "DISC  
TITLE ?/TITLE ? (for track title)" is dis-  
played.  
The "EDIT" indicator appears on the display.  
DIVIDE=JOIN=MOVE=ERASE=ALL ERASE=DISC  
TITLE=TITLE=(Back to the beginning)  
Erasing all the Tracks  
(ALL ERASE Function)  
Use the Remote Control to carry out this function.  
4.Press the SET button.  
For DISC TITLE:  
Cursor  
Alternates  
Cursor  
EDIT  
/TITLE  
SET  
1.Insert an MD to be edited with its label side  
up.  
Title name area  
Characters to be input  
2.Press the MD 38 button and then 7 button  
For TITLE (Track Title):  
to set the function to MD.  
Track to be given the title  
EDIT  
/TITLE  
The track numbers and total playback time are displayed.  
SET  
3.Press the EDIT/TITLE button until “ALL  
ERASE ?” is displayed.  
1 Select the track number to be given the title using the UP,  
DOWN, >, or < button. (For details, see step 5 in "Divid-  
ing Tracks (DIVIDE Function)".)  
The "EDIT" indicator appears on the display.  
DIVIDE=JOIN=MOVE=ERASE=ALL ERASE=DISC  
TITLE=TITLE=(Back to the beginning)  
2 Press the SET button.  
4.Press the SET button.  
Cursor  
Alternates  
EDIT  
/TITLE  
Cursor  
Alternates  
SET  
SET  
Title name area  
Characters to be input  
19  
The letter N is now displayed in the title area.  
5.Input a preferred title (up to 32 charac-  
ters).  
Use the following buttons to input a title.  
[Title editing buttons and their functions] (see below)  
4. Select “(space)” and press the SET button.  
5. Press the DISPLAY/CHARA button until the numbers are  
displayed.  
6. Select “1” and press the SET button.  
The title name "N(space)1" will be displayed.  
Editing the Title Name:  
Button  
Function  
DISPLAY  
/CHARA  
Changes the type of characters to be input as fol-  
lows.  
Upper-case letters and symbols +  
If the wrong character has been input, clear it using the  
CANCEL button.  
Lower-case letters and symbols  
Numbers  
To clear a particular character which has been input, use the  
¢or 4button to align the cursor with the character, and  
press the CANCEL button. Then, select the correct charac-  
ter and press the SET button.  
>
<
Moves the cursor for the character to be input to  
the right.  
Moves the cursor for the character to be input to  
the left.  
6.Press the EDIT/TITLE button.  
Selects the characters in the upper row in the  
character set.  
EDIT  
Alternates  
/TITLE  
UP  
e.g. FGHIJ= ABCDE  
Selects the characters in the lower row in the  
character set.  
DOWN  
e.g. ABCDE = FGHIJ  
7.Press the EDIT/TITLE button again.  
¢
4
The "EDIT" indicator disappears on the display.  
Moves the cursor for the title name to the right.  
Moves the cursor for the title name to the left.  
8.Press the MD0 button to complete editing.  
The MD is ejected after "UTOCwriting" is displayed.  
Example: When input the title “N(space)1”  
1. Display the letter N to be input.  
You can also complete editing operation by pressing the  
button to turn off the power.  
Press the > button until the letter N is displayed.  
OR  
Press the DOWN button until "KLMNO" is displayed.  
To cancel the operation, press the CANCEL button in step 6.  
Note: While "UTOCwriting" is displayed, do not disconnect the  
power cord or subject the Unit to the vibration to avoid in-  
correct recording.  
2. Select “N” (put the cursor to the letter N using the > or < but-  
ton).  
3. Press the SET button.  
[Character Layout Table]  
You can write album or song names to a disc, using the following characters:  
Uppercase letters  
Lowercase letters  
Numbers  
A
F
B
G
L
C
H
D
I
E
J
a
f
b
g
l
c
h
d
i
e
j
0
5
1
6
2
7
3
8
4
9
K
P
U
M N  
O
T
Y
k
p
u
m
r
n
s
x
o
t
Q
V
R
S
q
v
W X  
w
y
Z
z
(space)  
(space)  
!
#
$
!
#
$
% &  
(
-
)
.
% &  
,
;
(
-
)
.
*
/
+
:
,
;
*
/
+
:
<
=
`
<
=
>
?
@ _  
>
?
@ _  
`
20  
Using External Equipments  
■  
REMOTE CONTROL RM-RXUMD9000R  
DIMMER SLEEP  
CLOCK FM MODE TAPE/AUX  
TAPE/AUX  
AHB.  
AUTO  
SUPER PRO PRESET  
PROGRAM RANDOM REPEAT  
TIMER/  
SNOOZE  
DISPLAY  
MODE  
BASS  
TREBLE  
CANCEL  
PTY/EON  
DOWN  
MULTI CONTROL  
UP  
CLOCK  
EDIT  
/TITLE  
DISPLAY  
/CHARA  
OPEN/CLOSE  
CD  
UP  
TAPE  
/AUX  
MD  
CD  
TUNER  
BAND  
TAPE/AUX  
EJECT  
MD  
CD SYNCHRO  
REC  
REC  
PAUSE  
SET  
VOLUME  
<
>
DOWN  
UP  
DOWN  
PTY/EON  
MD  
DISPLAY MODE  
CD  
TUNER  
BAND  
VOLUME  
Listening to External  
Equipment  
Recording to External  
Equipment  
You can listen to external equipment.  
You can record the System's source to external equipment which is  
connected to the LINE OUT terminals of the System, such as cas-  
sette deck, etc.  
First make sure that the external equipment is properly connect-  
ed to the System. (See page 4).  
First make sure that the external equipment is properly connect-  
1.Set the VOLUME control to the minimum  
ed to the System. (See page 4).  
position.  
1.Play the System's CD Player, MD Player, or  
2.Press the TAPE/AUX button.  
tune into a station.  
The display changes with each press of the button, as shown be-  
The recording level is not affected by the VOLUME level set by  
the System. Also it is not affected by the sound effects.  
Note: For operation of the external equipment, refer to its Instruc-  
tions.  
low.  
When the “AUX 1 ANALOG IN” is selected:  
You can use the external equipment connected to the LINE IN  
(AUX1) terminals of the System, such as cassette deck, turnta-  
ble, etc.  
To listen to the external equipment, start playing the exter-  
nal equipment.  
When the "AUX 2 DIGITAL IN" is selected:  
You can use the external equipment connected to the OPTICAL  
DIGITAL IN (AUX2) terminal of the System, such as CD play-  
er, etc.  
To listen to the external equipment, start playing the exter-  
nal equipment.  
3.Adjust the VOLUME control to the desired  
listening level.  
4.Apply sound effects, if you wish.  
Press the AHB Super PRO button to reinforce the bass sound.  
Press the BASS/TREBLE button to control the tone. (See  
"Tone Control" on page 7.)  
Note: For operation of the external equipment, refer to its Instruc-  
tions.  
21  
Using the Timers  
■  
REMOTE CONTROL RM-RXUMD9000R  
DIMMER SLEEP  
SLEEP  
4
CLOCK FM MODE TAPE/AUX  
¢
AHB.  
AUTO  
SUPER PRO PRESET  
CLOCK  
ON time, OFF time, Source, Volume  
TIMER/  
SNOOZE  
DISPLAY  
MODE  
PROGRAM RANDOM REPEAT  
PTY/EON  
DOWN  
MULTI CONTROL  
UP  
CLOCK  
TIMER/  
SNOOZE  
BASS  
TREBLE  
CANCEL  
OPEN/CLOSE  
CD  
MD  
CD  
TAPE  
/AUX  
TUNER  
BAND  
EDIT  
/TITLE  
DISPLAY  
/CHARA  
EJECT  
MD  
CD SYNCHRO  
REC  
REC  
PAUSE  
VOLUME  
UP  
DOWN  
UP  
SET  
<
>
Timer  
indicator  
DOWN  
PTY/EON  
MD  
DISPLAY MODE  
CD  
TUNER  
BAND  
SLEEP  
indicator  
When the System is in use, the display shows other items as well.  
For simplicity, we show here only the items described in this section.  
SNOOZE indicator  
VOLUME  
The timers let you control listening and recording functions auto-  
matically.  
1. Press the TIMER/SNOOZE button on the Unit.  
The Timer indicator lights up and the current ON time  
blinks on the display.  
Setting the Clock  
When you plug the AC power cord into the wall outlet, the time  
indication blinks on the display.  
2. Press the ¢or 4button on the Unit to set the time you  
want the Unit to come on.  
You can set the clock whether the System is on or off.  
Pressing the ¢button moves the time forwards and press-  
ing the 4button moves it backwards. Hold down the but-  
ton to move the time in 10-minute intervals.  
Note:  
The clock must be correctly set for the timers to work.  
The procedure must be completed within two minutes. Other-  
wise, the setting is cleared and must be repeated from the  
beginning.  
DOWN  
MULTI CONTROL  
UP  
CLOCK  
CLOCK  
3.Setting the OFF time (Example: 13:15).  
1. Press the TIMER/SNOOZE button on the Unit.  
The current OFF time blinks on the display.  
(for 2 seconds)  
1.Press the CLOCK button on the Unit for  
more than two seconds.  
2. Press the ¢or 4button on the Unit to set the time you  
want the Unit to be turned off.  
The time indication rapidly blinks on the display.  
Pressing the ¢button moves the time forwards and press-  
ing the 4button moves it backwards. Hold down the but-  
ton to move the time in 10-minute intervals.  
4
2.Press the  
or  
button on the Unit to set  
¢
the time.  
Pressing the ¢button moves the time forwards and pressing  
the 4button moves it backwards. Hold down the button to  
move the time in 10-minute intervals.  
3.Press the CLOCK button.  
4.Selecting the music source.  
The selected time is set and the seconds start counting from 0.  
1. Press the TIMER/SNOOZE button on the Unit.  
The "TUNER" blinks on the display.  
2. Press the ¢or 4button to select the music source you  
want to listen to.  
CAUTION: If there is a power failure, the clock  
loses its setting after about 20 minutes. “0:00”  
blinks on the display and the clock must be reset.  
The display changes as shown below.  
TUNERÔTUNER RECÔCDÔMDÔ(back to the be-  
ginning)  
Setting the Daily Timer  
When you select the “TUNER REC”, the “REC” indicator  
appears on the display.  
Once you have set the Daily Timer, the timer will be activated at the  
same time every day. It can be cancelled and re-activate whenever  
you wish.  
The Timer indicator on the display shows when the Daily Timer you  
have set is in effect.  
Note: Perform each setting within 30 seconds. Otherwise, setting  
is cleared and the procedure must be repeated from the be-  
ginning.  
5.Setting the volume level.  
1. Press the TIMER/SNOOZE button on the Unit.  
The current volume setting blinks on the display.  
2. Press the ¢or 4button to select the volume level.  
--  
: The current volume level will be used.  
0 to 50: When the timer is turned on, the Volume will be  
automatically set to the selected level.  
1.Press the  
button to turn on the System.  
2.Setting the ON time (Example: 12:15).  
22  
6.Press the TIMER/SNOOZE button on the  
Setting the SLEEP Timer  
Unit.  
Use the Sleep Timer to turn the System off after a certain number of  
minutes when it is playing. By setting the Sleep Timer, you can fall  
asleep to music and know that your System will turn off by itself  
rather than play all night.  
The timer setting is completed and the display returns to the dis-  
play before you set the timer. The timer indicator remains lit.  
7.Before turning off the System, prepare the  
music source selected in step 4.  
TUNER: Tune in to the desired station.  
TUNER REC: Tune in to the desired station and insert an MD  
for recording the station.  
You can only set the Sleep Timer when the System is on and a  
source is playing.  
1. Play a CD, MD, or tune in to the desired sta-  
tion.  
CD: Insert a CD.  
MD: Insert an MD.  
2. Press the SLEEP button on the Remote  
Control.  
8.Press the  
button to turn off the System.  
The "SLEEP" indicator lights up.  
To cancel the timer, press the TIMER/SNOOZE button. The  
Timer indicator goes out on the display.  
3. Set the length of time you want the source  
To re-activate the cancelled timer, press the TIMER/  
SNOOZE button to light the Timer indicator. Then, press the TIM-  
ER/SNOOZE button until the display returns to the original display.  
To confirm the timer settings, cancel the timer once by press-  
ing the TIMER/SNOOZE button. Then, press the TIMER/  
SNOOZE button repeatedly, to see the current timer settings (ON  
time, OFF time, source, and volume).  
to play before shutting off.  
Each time you press the SLEEP button, it changes the number  
of minutes shown on the display in this sequence:  
=30 =60 =90 =120 =Cancelled =(back to the begin-  
ning)  
After setting the number of minutes for the Sleep Timer, the display  
will stop blinking and return to the display as before setting the  
Sleep Timer. (The display is dimmed.)  
The System is now set to turn off after the number of minutes you  
set.  
To change the timer setting, repeat the setting procedure from  
the beginning.  
When the timer turns on, the Timer indicator starts blinking  
and the volume level gradually increases from 0 (zero) to the  
preset level, except when you set the volume level to “– –” in  
step 5.  
To Confirm the Sleep Time  
When the SLEEP button is pressed, the remaining sleep time is dis-  
played. Wait until the display returns to the original display.  
To Cancel the SLEEP Timer Setting  
Press the SLEEP button until the “SLEEP” indicator goes out on the  
display.  
Turning off the System also cancels the SLEEP Timer.  
If you are setting the Daily Timer, the System will be turned on  
at the set time to wake you up.  
CAUTION: If the System is unplugged, or a power  
failure occurs, the timer setting will be lost. You  
will need to reset the clock first, then the timer.  
5-Minute Snoozing —————————  
When the timer turns on the music source you can, if you wish, ac-  
tivate the 5-minute snoozing function to temporarily stop playback.  
Press the TIMER/SNOOZE button on the Unit.  
The “SNOOZE” indicator lights up on the display and the power is  
turned off for five minutes for snoozing.  
Information on MDs (Minidiscs)  
■  
This is a new digital audio disc format: it has a diameter of 64 mm and enables up to 74 minutes of playback and recording.  
Playback-only MD  
The cartridge  
This is the type used for commercially-available pre-recorded MDs,  
The diameter of the disc itself is 64 mm, smaller than a CD single.  
The disc sits inside a 68 x 72 mm cartridge, which also being pocket  
size, makes minidiscs extremely handy for carrying and storage.  
Since the disc is protected by the cartridge, dust and dirt cannot eas-  
ily get into it. And thanks to a shutter which is closed at all times  
except during use, there is no need to worry about scratches or fin-  
ger marks, making the handling of minidiscs very simple.  
on which recording cannot be done. Like a CD, data is recorded  
based on the presence or absence of small indentations called pits.  
A disc recorded with this format is called an “optical disc.”  
SOUND  
Cartridge  
Recordable MDs  
Disc  
These are the so-called “blank” MDs you can use to make your own  
recordings. Data is recorded by magnetism, which is easily proc-  
essed, so that recording can be done again and again. By using a la-  
ser to heat the disc, the magnetism is erased and the magnetic head  
records the new data. Discs with this type of recording method are  
called magneto-optical (MO) discs.  
Shutterc  
Two types of minidisc  
There are two types of minidisc, “recordable MDs” and “playback-  
only MDs.” The playback method for each is the same: a laser irra-  
diates the disc and the signal is read from the beam which comes  
back. However, the recording method for each type is different.  
23  
ATRAC (Adaptive Transform Acous-  
tic Coding)  
Optical pickup  
Within recordings, there are sounds which cannot be readily heard.  
For example, as the volume decreases, high-pitched sounds and  
low-pitched sounds become difficult to hear. also, if a quiet sound  
comes at the same time as or just after a loud sound, it will not be  
heard. With minidiscs, data is compressed using a technology called  
ATRAC (Adaptive Transform Acoustic Coding) which selectively  
chooses sounds based on human sense of hearing characteristics.  
With this technology, the recorded data is about one-fifth the vol-  
ume of the original data, allowing it to fit on a compact minidisc.  
STOP  
Sound jump  
guard menory  
During normal play  
When vibration has occurred  
(dB)  
+20  
UTOC (User Table Of Contents)  
0
Sharp  
In a minidisc, apart from the recorded tracks, there is the “UTOC”.  
In this area, information such as the position where each track is re-  
corded, the track divisions, and track order are listed. When music  
search is done, the UTOC is consulted, and the tracks are quickly  
found and played back. When editing is done, only the UTOC is  
changed, so there is no need to re-record the tracks.  
»
-20  
Sensitivity  
of our ears  
-40  
«
-60  
Dull  
5k 10k 15k  
(Hz)  
20 50 100  
500 1k  
Low | Sound range \High  
UTOC  
Sound range and sensitivity of our ears  
Contents  
1. Track A: Page 9  
Track details  
2. Track B: Page 6  
3. Track C: Page 10  
Sound skip guard memory  
÷
÷
÷
With the minidisc, the data of the track being played can be tempo-  
rarily stored up using a function called “sound skip guard memory”.  
Even when data cannot be collected properly from the disc due to  
shaking or vibrations, information is stored in the “sound skip guard  
memory”, so that there is no break in the sound which is actually de-  
livered.  
MD (Minidisc) Error Messages  
■  
Error messsage  
Meaning  
Action  
A disc has been inserted with nothing  
recorded on it.  
Except when making a new recording,  
replace the disc with one which has been  
recorded on.  
BLANK DISC  
You have tried to join tracks which cannot  
be joined.  
This is a limitation of the minidisc system.  
See “Minidics limitations” on page 25.  
CANNOT JOIN  
DISC ERROR  
There is a problem (damage) with the disc.  
5HSODFHýWKHýGLVFïï  
7KHUHýLVýQRWýHQRXJKýVSDFHýOHIWýRQýWKHýGLVFï  
7KHUHýDUHýRYHUýëèéýWUDFNVï  
5HSODFHýWKHýGLVFýZLWKýDQRWKHUýUHFRUGDEOHý  
0'ï  
DISC FULL  
The disc is in accidental erasure protection  
mode.  
Slide the accidental erasure protection tab.  
(So that the hole is covered.)  
DISC PROTECTED  
$ýPDOIXQFWLRQýRFFXUUHGýGXULQJýUHFRUGLQJï  
6WRSýWKHýGLVFýE\ýSUHVVLQJýWKHý7ýEXWWRQýDQGý  
UHGRýWKHýRSHUDWLRQï  
EMERGENCY STOP  
NO DISC  
7KHUHýLVýQRýGLVFýLQýWKHýXQLWï  
,QVHUWýDýGLVFýLQWRýWKHýXQLWï  
6WRSýUHFRUGLQJï  
NON AUDIO  
CANNOT COPY  
<RXýKDYHýWULHGýWRýGLJLWDOO\ýGXEýDý&'ð  
520  
<RXýKDYHýWULHGýWRýUHFRUGýRUýHGLWýRQýDýSOD\ð  
EDFNðRQO\ýGLVFï  
5HSODFHýWKHýGLVFýZLWKýDýUHFRUGDEOHý0'ï  
PLAYBACK MD  
7KHýWUDFNýLVýSURWHFWHGï  
7KLVýXQLWýFDQQRWýXQGRýWUDFNýSURWHFWLRQïý  
8QGRýWKHýSURWHFWLRQýXVLQJýWKHýDSSOLDQFHý  
WKDWýFUHDWHGýLWï  
TRACK  
PROTECTED  
SCMS  
CANNOT COPY  
<RXýKDYHýWULHGýWRýPDNHýDýFRS\ýRIýDýFRS\ý  
E\ýGLJLWDOýGXEELQJï  
'XEýXVLQJýDQDORJXHýLQSXWýõ/,1(ý,1ôï  
DIGITAL IN  
UNLOCK  
7KHýGLJLWDOýFDEOHýLVýGLVFRQQHFWHGï  
&RQQHFWýWKHýGLJLWDOýFDEOHýVHFXUHO\ï  
24  
Minidisc limitations  
■  
The minidisc records information in an original format that differs from that of conventional cassette tapes or DATs. Since there are some lim-  
itations with this recording format, the following types of conditions may arise. These conditions arre not malfunctions.  
Condition  
Cause  
“DISC FULL” is displayed, even though  
the possible recording time is not used up.  
With the minidisc, there is a maximum number of tracks which can be recorded, regardless of  
time. More than 254 tracks cannot be recorded on a disc.  
“DISC FULL” is displayed, even though  
the number of tracks and recording time  
are not at the limit.  
When parts of the disc are erased and re-recorded, blank spots are created on the disc. When  
recording to such a disc, one track of data is divided and recorded in the blank areas. During  
recording, when these divided parts become numerous, the “DISC FULL” message may be  
displayed. When a part of 8 seconds or less is created by division, that track cannot be joined  
by the JOIN function, and even if it is erased, the remaining usable time on the disc does not  
increase. Tracks divided into small pieces may skip when fast forward or fast rewind is done.  
The JOIN function sometimes does’t work  
The remaining usable time on the disc  
doesn’t increase even when tracks are  
erased.  
The sound skip during fast forward or fast  
rewind.  
The amount of recorded time on the disc  
added to the amount of remaining time  
falls shout of the disc’s total possible  
recording time.  
Minidiscs must have at least 2 seconds of continuous space in order to record. For this rea-  
son, the actual recording time of discs with a lot of short blank areas becomes shorter.  
Rules of Digital Dubbing  
■  
The following rules regarding copyright exist for dubbing to MDs from CDs or DATs through digital terminals.  
SCMS (Serial Copy Management System)  
Minidiscs can record clear sound with low loss of quality from CDs or DATs through each component’s digital input/output terminal. However,  
minidiscs are set up so that a disc recorded in this way cannot be recorded onto another minidisc through digital input/output terminals. In other  
words, you can not make a copy of a copy. This rule is called SCMS (Serial Copy Management System).  
The recorder is designed in compliance with this rule. If you try to make a copy of a copy the error message “SCMS CANNOT COPY” is  
displayed, and dubbing can not be done.  
OK  
NO  
DIGITAL  
DIGITAL  
It may be unlawful to record or play back copyrighted material without the consent of the copyright owner.  
25  
Care And Maintenance  
■  
+DQGOHý\RXUý&'VýDQGý0'VýFDUHIXOO\ñýDQGýWKH\ýZLOOýODVWýDýORQJýWLPHï  
Cleaning the lens  
,IýWKHýOHQVýLQýWKHý&'ýSLFNXSýLVýGLUW\ñýGURSRXWñýHWFïñýFRXOGýGHJUDGHý  
VRXQGï  
Compact Discs  
2QO\ý&'VýEHDULQJýWKLVýPDUNýFDQýEHýXVHGýZLWKý  
WKLVý6\VWHPïý+RZHYHUñýFRQWLQXHGýXVHýRIýLUUHJXð  
ODUýVKDSHý&'VýõKHDUWðVKDSHñýRFWDJRQDOñýHWFïôý  
FDQýGDPDJHýWKHý6\VWHPï  
2SHQýWKHý&'ýKROGHUýDQGýFOHDQýWKHýOHQVýDVýVKRZQï  
8VHýDýEORZHUýõDYDLODEOHýIURPýDýFDPHUDýVWRUHôýWRýEORZýGXVWýRIIý  
WKHýOHQVï  
Blower  
Lens  
5HPRYHýWKHý&'ýIURPýLWVýFDVHýE\ýKROGLQJýLWýDWý  
WKHýHGJHVýZKLOHýSUHVVLQJýWKHýFDVH©VýFHQWHUýKROHý  
OLJKWO\ï  
'RýQRWýWRXFKýWKHýVKLQ\ýVXUIDFHýRIýWKHý&'ñýRUý  
EHQGýWKHý&'ï  
STANDBY  
,IýWKHUHýDUHýILQJHUSULQWVñýHWFïýRQýWKHýOHQVñýJHQWO\ýZLSHýFOHDQýZLWKý  
DýFRWWRQýVZDEï  
3XWýWKHý&'ýEDFNýLQýLWVýFDVHýDIWHUýXVHýWRýSUHYHQWý  
ZDUSLQJï  
%HýFDUHIXOýQRWýWRýVFUDWFKýWKHýVXUIDFHýRIýWKHý&'ý  
ZKHQýSODFLQJýLWýEDFNýLQýWKHýFDVHï  
$YRLGýH[SRVXUHýWRýGLUHFWýVXQOLJKWñýWHPSHUDWXUHý  
H[WUHPHVñýDQGýPRLVWXUHïý  
$ýGLUW\ý&'ýPD\ýQRWýSOD\ýFRUUHFWO\ïý,IýDý&'ý  
GRHVýEHFRPHýGLUW\ñýZLSHýLWýZLWKýDýVRIWýFORWKýLQýDý  
VWUDLJKWýOLQHýIURPýFHQWHUýWRýHGJHïý  
The cabinet of the speaker is coated with high-grade polished  
paint. When dirt such as a fingerprint, dust, etc. is stuck to the cab-  
inet, first, dust the coating surface with the attached polishing  
cloth. Next, lightly wipe off the dirt.  
CAUTION: Do not use any solvent (for example,  
conventional record cleaner, spray thinner, ben-  
zine, etc.) to clean a CD.  
If the polishing cloth is dirty, wash it using a synthetic detergent.  
MDs (Minidiscs)  
Do not open the shutter. Since the shutter is  
locked to prevent it from opening, forcing it to  
open will break the disc.  
Moisture Condensation  
0RLVWXUHýPD\ýFRQGHQVHýRQýWKHýOHQVýLQVLGHýWKHý  
6\VWHPýLQýWKHýIROORZLQJýFDVHVã  
$IWHUýWXUQLQJýRQýKHDWLQJýLQýWKHýURRPï  
,QýDýGDPSýURRPï  
,IýWKHý6\VWHPýLVýEURXJKWýGLUHFWO\ýIURPýDýFROGý  
WRýDýZDUPýSODFHï  
6KRXOGýWKLVýRFFXUñýWKHý6\VWHPýPD\ýPDOIXQFWLRQïý  
,QýWKLVýFDVHñýOHDYHýWKHý6\VWHPýWXUQHGýRQýIRUýDý  
IHZýKRXUVýXQWLOýWKHýPRLVWXUHýHYDSRUDWHVñýXQSOXJý  
WKHý$&ýSRZHUýFRUGñýDQGýWKHQýSOXJýLWýLQýDJDLQï  
General Notes  
,QýJHQHUDOñý\RXýZLOOýKDYHýWKHýEHVWýSHUIRUPDQFHýE\ýNHHSLQJý\RXUý  
&'Vñý0'VñýDQGýWKHýPHFKDQLVPýFOHDQï  
6WRUHý&'VýDQGý0'VýLQýWKHLUýFDVHVñýDQGýNHHSýWKHPýLQýFDELQHWVýRUý  
RQýVKHOYHVï  
Keep the system’s CD holder closed when not in use.  
26  
Troubleshooting  
,Iý\RXýDUHýKDYLQJýDýSUREOHPýZLWKý\RXUý6\VWHPñýFKHFNýWKLVýOLVWýIRUýDýSRVVLEOHýVROXWLRQýEHIRUHýFDOOLQJýIRUýVHUYLFHï  
,Iý\RXýFDQQRWýVROYHýWKHýSUREOHPýIURPýWKHýKLQWVýJLYHQýKHUHñýRUýWKHý6\VWHPýKDVýEHHQýSK\VLFDOO\ýGDPDJHGñýFDOOýDýTXDOLILHGýSHUVRQñýVXFKýDVý  
\RXUýGHDOHUñýIRUýVHUYLFHï  
■  
Symptom  
Possible Cause  
Action  
1RýVRXQGýLVýKHDUGï  
&RQQHFWLRQVýDUHýLQFRUUHFWñýRUýORRVHï  
&KHFNýDOOýFRQQHFWLRQVýDQGýPDNHýFRUUHFð  
WLRQVïýõ6HHýSDJHVýéðýèïô  
'LVFRQQHFWýWKHýKHDGSKRQHVï  
+HDGSKRQHVýDUHýFRQQHFWHGï  
3RRUýUDGLRýUHFHSWLRQ  
7KHýDQWHQQDýLVýGLVFRQQHFWHGï  
7KHý$0ý/RRSý$QWHQQDýLVýWRRýFORVHýWRýWKHý  
6\VWHPï  
5HFRQQHFWýWKHýDQWHQQDýVHFXUHO\ï  
&KDQJHýWKHýSRVLWLRQýDQGýGLUHFWLRQýRIýWKHý  
$0ý/RRSý$QWHQQDï  
7KHý)0ý:LUHý$QWHQQDýLVýQRWýSURSHUO\ý  
H[WHQGHGýDQGýSRVLWLRQHGï  
([WHQGý)0ý:LUHý$QWHQQDýWRýWKHýEHVWý  
UHFHSWLRQýSRVLWLRQï  
7KHý&'ýVNLSVï  
7KHý&'ýLVýGLUW\ýRUýVFUDWFKHGï  
7KHý&'ýLVýXSVLGHýGRZQï  
&OHDQýRUýUHSODFHýWKHý&'ï  
7KHý&'ýGRHVýQRWýSOD\ï  
7KHý0'ýFDQQRWýEHýLQVHUWHGï  
3XWýWKHý&'ýLQýZLWKýWKHýODEHOýVLGHýXSï  
$Qý0'ýKDVýDOUHDG\ýEHHQýLQVHUWHGï  
3UHVVýWKHý0'0ýEXWWRQýWRýHMHFWýWKHýLQVHUWHGý  
0'ýDQGýLQVHUWýDýQHZý0'ï  
5HFRUGLQJýFDQQRWýEHýPDGHýRQý0'ï  
7KHýDFFLGHQWDOýHUDVXUHýSUHYHQWLRQýNQREýRIýWKHý  
0'ýLVýVHWýWRýWKHýRSHQýSRVLWLRQï  
6HWýLWýWRýWKHýFORVHýSRVLWLRQï  
7LPHUýIDLOVýWRýVWDUWï  
3UHVHQWýWLPHýLVýQRWýFRUUHFWï  
6HWýWKHýWLPHýFRUUHFWO\ï  
8QDEOHýWRýRSHUDWHýWKHý5HPRWHý&RQWUROï  
7KHýSDWKýEHWZHHQýWKHý5HPRWHý&RQWUROýDQGý  
WKHýVHQVRUýRQýWKHý8QLWýLVýEORFNHG  
7KHýEDWWHULHVýKDYHýORVWýWKHLUýFKDUJHï  
5HPRYHýWKHýREVWUXFWLRQï  
5HSODFHýWKHýEDWWHULHVï  
2SHUDWLRQVýDUHýGLVDEOHGï  
7KHýEXLOWðLQýPLFURSURFHVVRUýKDVýPDOIXQFð  
WLRQHGýGXHýWRýH[WHUQDOýHOHFWULFDOýLQWHUIHUHQFHï  
8QSOXJýWKHý6\VWHPýWKHQýSOXJýLWýEDFNýLQ  
27  
Specifications  
■  
Amplifier  
2XWSXWý3RZHU êíý:ýõìèý:ýòýìèý:ôýDWýéýRKPVýõ0D[ïô  
ëíý:ýõìíý:ýòýìíý:ôýDWýéýRKPVýõìíøý7+'ô  
,QSXWý6HQVLWLYLW\î,PSHGDQFHýõìýN+]ô  
/,1(ý,1ýõ$8;ýìô èííýP9îçíýNRKPV  
2SWLFDOý,Q ¤ëéýG%Pýðý¤ìèýG%P  
2XWSXWý6HQVLWLYLW\î,PSHGDQFHýõìýN+]ô  
/,1(ý287 èííýP9îèýNRKPV  
6XEZRRIHU íýðýìééýP9îêíýNRKPV  
6SHDNHUýWHUPLQDOV éýðýìçýRKPV  
3KRQHV ìçýRKPVýðýìýNRKPV  
MD Player  
:RZý$QGý)OXWWHU 8QPHDVXUDEOH  
CD Player  
:RZý$QGý)OXWWHU 8QPHDVXUDEOH  
Tuner  
)0ý7XQHU  
7XQLQJý5DQJH åæïèýðýìíåïíý0+]  
$0ý7XQHU  
7XQLQJý5DQJHý õ0:ôýèëëýðýìñçëäýN+]  
õ/:ôýìééýðýëååýN+]  
Speaker Specifications  
õHDFKýXQLWôý6SHDNHUV åýFPýFRQH  
,PSHGDQFH éýRKPV  
'LPHQVLRQV ìëíýýìçíýýìäíýPPýõ:î+î'ôý  
0DVV $SSUR[ïýìïêýNJ  
General  
'LPHQVLRQV êåíýýìçéýýêíìýPPýõ:î+î'ôý  
0DVV $SSUR[ïýçïéýNJ  
Accessories  
3RZHUý&RUGýõìô  
$0ý/RRSý$QWHQQDýõìô  
5HPRWHý&RQWUROýõìô  
%DWWHULHVý5ç3ýõ680ðêôî$$ýõìè)ôýõëô  
)0ý:LUHý$QWHQQDýõìô  
6SHDNHUý&RUGVýõëô  
3ROLVKLQJý&ORWKýõìô  
Power Specifications  
3RZHUý5HTXLUHPHQWV $&ýëêíý9ýaýñýèíý+]ý  
3RZHUý&RQVXPSWLRQ êíýZDWWVýõSRZHUýRQýPRGHô  
èýZDWWVýõLQý6WDQGE\ýPRGHô  
'HVLJQýDQGýVSHFLILFDWLRQVýDUHýVXEMHFWýWRýFKDQJHýZLWKRXWýQRWLFHï  
28  
VICTOR COMPANY OF JAPAN, LIMITED  
EN, GE, FR, NL, SP, IT  
0598MNMCREOZK  

NAD 501 User Manual
Microsoft Software Office 365 Home Premium 6GQ00024 User Manual
Metra Electronics 99 8206 User Manual
Meridian America 506 User Manual
LG Electronics 5400 User Manual
Kyocera 5100 Series User Manual
Fujitsu Computer Drive MHY2200BS User Manual
Cuisinart Grind &amp; Brew Thermal DGB 650BC User Manual
Compaq Surestore DLT 80 User Manual
Black &amp; Decker DCM902WH User Manual