CD RECEIVER
KD-G731
For canceling the display demonstration, see page 4.
For installation and connections, refer to the separate manual.
INSTRUCTIONS
GET0431-003A
[EX/EU]
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to
qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical
instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Warning:
How to reset your unit
If you need to operate the unit while driving, be
sure to look around carefully or you may be involved
in a traffic accident.
This symbol is only valid in
the European Union.
•
Your preset adjustments will also be erased (except
the registered Bluetooth device, see page 14).
Information for Users on Disposal of Old
Equipment
This symbol indicates that the product with
this symbol should not be disposed as general
household waste at its end-of-life. If you wish to
dispose of this product, please do so in accordance
with applicable national legislation or other rules in
your country and municipality. By disposing of this
product correctly, you will help to conserve natural
resources and will help prevent potential negative
effects on the environment and human health.
How to forcibly eject a disc
“PLEASE” and “EJECT” appear alternately on the
display.
•
•
Be careful not to drop the disc when it ejects.
If this does not work, reset your unit.
2
How to use functions mode
CONTENTS
If you press M MODE, the unit goes into functions
mode, then the number buttons (except “4”) and
5/∞ buttons work as different function buttons.
INTRODUCTIONS
Preparation ............................................
4
OPERATIONS
[Within 5 seconds...]
Basic operations ......................................
• Using the control panel.......................
• Using the remote controller
5
5
(RM-RK50).........................................
Listening to the radio ...............................
Searching for FM RDS programme
6
8
Caution on volume setting:
—PTY Search.......................................
9
Disc operations........................................ 11
Listening to the USB device ....................... 12
Discs and connected USB devices produce very
little noise compared with other sources. Lower
the volume before playing to avoid damaging the
speakers by the sudden increase of the output level.
EXTERNAL DEVICES
Using the Bluetooth devices ................... 14
®
• Using the Bluetooth cellular phone ..... 16
• Using the Bluetooth audio player ........ 18
Listening to the CD changer ...................... 18
Listening to the DAB tuner........................ 20
Listening to the iPod / D. player................. 21
Listening to the other external
Note: Only for [EX] model users in UK and
European countries
For security reasons, a numbered ID card is provided
with this unit, and the same ID number is imprinted on
the unit’s chassis. Keep the card in a safe place, as it will
help the authorities to identify your unit if stolen.
components......................................... 22
For safety...
SETTINGS
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
Selecting a preset sound mode.................. 24
General settings—PSM ........................... 25
Bluetooth settings ................................... 28
Temperature inside the car...
REFERENCES
If you have parked the car for a long time in hot or cold
weather, wait until the temperature in the car becomes
normal before operating the unit.
Maintenance ........................................... 29
More about this unit ................................ 30
Troubleshooting ...................................... 34
Specifications .......................................... 38
3
Preparation
Cancel the display demonstration and set the clock
• See also page 26.
When the power is turned off: Check the current clock time
When the power is turned on: Change the display information
~
Ÿ
Turn on the power.
Enter the PSM settings.
!] ⁄ Cancel the display demonstrations
Select “DEMO,” then “DEMO OFF.”
Set the clock
Select “CLOCK H” (hour), then adjust the hour.
Select “CLOCK M” (minute), then adjust the minute.
Select “24H/12H,” then “24H” (hour) or “12H” (hour).
@
Finish the procedure.
Detaching the control panel
Attaching the control panel
Lever
CAUTION:
The lever comes out if you pressed the 0 button while the panel
is detached. If this happens, push the lever back into lock position
before attaching the panel.
4
INTRODUCTIONS
Basic operations
Using the control panel
1
Select the source.
q
Enter functions mode.
FM/AM = DAB * = CD * = USB * = CD-CH */
IPOD */D.PLAYER * (or EXT IN) = BT-PHONE
(Bluetooth Phone)* = BT-AUDIO (Bluetooth
Audio)* = (back to the beginning)
* You cannot select these sources if they are not
ready or not connected.
Press M MODE, then one of the following buttons
(within 5 seconds)...
EQ : Select the sound mode.
MO : Turn on/off monaural reception.
SSM : Automatic station presetting [Hold].
RPT : Select repeat play.
RND : Select random play.
5/ ∞ : Skip 10 tracks.
2
3
Select the bands.
• Turn on the power.
w
e
• FM/AM/DAB: Select preset station/DAB service.
• CD/USB: Select folder/track/disc (for CD
changer).
• Turn off the power [Hold].
• Attenuate the sound (if the power is on).
• Volume control [Turn].
• BT-PHONE: Select preset phone number.
4
• Adjust the sound mode.
• Enter the PSM settings [Hold].
• FM/AM/DAB: Search for station/DAB ensemble.
• CD/USB: Select track.
5
6
Display window
• IPOD/D.PLAYER: Select track.
• BT-PHONE/BT-AUDIO: Select setting item/
Select a registered device.
• Activate/deactivate TA Standby Reception.
• Enter RDS programme search [Hold].
r
• DAB: Select DAB service.
• CD/USB: Select folder.
• IPOD/D.PLAYER: Enter the main menu/Pause or
stop playback/Confirm selection.
• BT-PHONE/BT-AUDIO: Enter setting menu/
Confirm selection.
7
8
9
p
Eject disc.
USB (Universal Serial Bus) input terminal
Detach the panel.
Change the display information.
OPERATIONS
5
Display window
1
2
3
4
5
Playback source indicators
Loudness indicator
9
p
Bluetooth indicator
Main display
(Time, menu, playback information)
Track information indicators
RDS indicators
q
w
Track indicator
Source display/Preset No./Track No./Folder No./
Disc No.
Sound mode indicators
•
lights up for the selected item.
e
Status of Bluetooth device
(Device number, [1 – 5]; signal strength, [0 – 3]*;
battery reminder, [0 – 3]*)
* As the number increases, the signal/battery
strength becomes stronger.
6
7
Tuner reception indicators
Playback mode/item indicators
(Random/Repeat)
8
Equalizer indicator
Using the remote controller (RM-RK50)
Before using the remote controller:
• Aim the remote controller directly at the remote
sensor on the unit.
Installing the lithium coin battery (CR2025)
• DO NOT expose the remote sensor to bright light
(direct sunlight or artificial lighting).
Remote sensor
6
• While playing an MP3 disc on an
MP3-compatible CD changer:
– Changes the disc if pressed briefly.
– Changes the folder if pressed and held.
• While listening to an Apple iPod or a JVC
D. player:
– Pauses/stops or resumes playback with D ∞.
– Enters the main menu with 5 U.
(Now 5 U/D ∞/2 R/F 3 work as the menu
selecting buttons.)*
Warning:
To prevent accidents and damage
• Do not install any battery other than CR2025 or
its equivalent.
• Do not leave the remote controller in a place
(such as dashboards) exposed to direct sunlight
for a long time.
• Store the battery in a place where children
cannot reach.
• Do not recharge, short, disassemble, heat the
battery, or dispose of it in a fire.
• Do not leave the battery with other metallic
materials.
• Do not poke the battery with tweezers or similar
tools.
3
4
5
6
Adjusts the volume level.
Selects the sound mode (iEQ: intelligent equalizer).
Selects the source.
For Bluetooth cellular phone:
• Wrap the battery with tape and insulate when
throwing away or saving it.
– Answers calls if pressed briefly.
– Rejects calls if pressed and held.
7
• Searches for stations (or DAB services) if pressed
briefly.
• Searches for DAB ensembles if pressed and held.
• Fast-forwards or reverses the track if pressed and
held.
• Changes the tracks if pressed briefly.
• While listening to an iPod or a D. player (in menu
selecting mode):
– Selects an item if pressed briefly. (Then, press
D ∞ to confirm the selection.)
– Skips 10 items at a time if pressed and held.
• Reverse skip/forward skip for Bluetooth audio.
1
• Turns the power on if pressed briefly or
attenuates the sound when the power is on.
• Turns the power off if pressed and held.
* 5 U
D ∞
:
:
Returns to the previous menu.
Confirms the selection.
2
• Changes the FM/AM/DAB bands with 5 U.
• Changes the preset stations (or DAB services)
with D ∞.
This unit is equipped with the steering wheel
remote control function.
• See the Installation/Connection Manual (separate
volume) for connection.
• Changes the folder of the MP3/WMA/AAC/WAV.
OPERATIONS
7
Listening to the radio
Select preset station.
Change the display information
Lights up when receiving an FM stereo
broadcast with sufficient signal strength.
~ Select “FM/AM.”
Ÿ Select the bands.
! Search for a station to listen—Auto Search.
Manual Search: Hold either one of the buttons until “M” flashes on the display, then press it repeatedly.
When an FM stereo broadcast is hard
to receive
3
1
Local FM stations with the strongest signals are
searched and stored automatically in the FM band.
2
Manual presetting
Ex.: Storing FM station of 92.5 MHz into preset number
4 of the FM1 band.
Reception improves, but stereo effect will be lost.
• MO indicator lights up.
1
2
3
FM station automatic presetting—
SSM (Strong-station Sequential
Memory)
You can preset up to six stations for each band.
1
2
8
Searching for FM RDS programme—PTY Search
Change the display information
~ Activate PTY Search.
Ÿ Select one of the PTY codes (programme types).
See the following for details.
! Start searching.
If there is a station broadcasting a programme of the same PTY code as you have selected, that station is tuned
in.
Preset PTY codes in the number buttons (1 to 6):
Storing your favorite programme
types
You can store your favorite PTY codes into the number
buttons.
PTY codes (available with the control dial):
NEWS, AFFAIRS, INFO, SPORT, EDUCATE, DRAMA,
CULTURE, SCIENCE, VARIED, POP M (music), ROCK M
(music), EASY M (music), LIGHT M (music), CLASSICS,
OTHER M (music), WEATHER, FINANCE, CHILDREN,
SOCIAL, RELIGION, PHONE IN, TRAVEL, LEISURE, JAZZ,
COUNTRY, NATION M (music), OLDIES, FOLK M (music),
DOCUMENT
1 Select a PTY code (see right column).
2 Select a preset number.
3 Repeat steps 1 and 2 for storing other
PTY codes.
4
OPERATIONS
9
Activating/deactivating TA/PTY Standby Reception
TA Standby Reception
Press to activate.
Indicator PTY Standby Reception
Indicator
See page 26.
The unit temporarily will switch to Traffic Lights up The unit temporarily will switch to your
Lights up
Announcement (TA), if available, from any
source other than AM*.
favorite PTY programme from any source
other than AM*.
The volume changes to the preset TA
volume level if the current level is lower
than the preset level (see page 26).
Not yet activated. Tune in to another
station providing the RDS signals.
Flashes
Goes off
Not yet activated. Tune in to another
station providing the RDS signals.
Flashes
Press
to deactivate.
Select “OFF” for the PTY code (see page 26) Goes off
to deactivate.
• When a DAB tuner is connected, TA/PTY Standby Reception also searches for services. (See also pages 20 and 26.)
* The unit will not switch to Traffic Announcement or PTY programme when a call connection is established through the
“BT-PHONE.”
Tracing the same programme—Network-Tracking Reception
When driving in an area where FM reception is not
sufficient enough, this unit automatically tunes in to
another FM RDS station of the same network, possibly
Programme A broadcasting on different frequency
areas (01 – 05)
broadcasting the same programme with stronger
signals (see the illustration on the right).
To change the Network-Tracking Reception
setting, see “AF-REG” on page 26.
• When the DAB tuner is connected, refer to “Tracing
the same programme—Alternative Frequency
Reception” on page 20.
Automatic station selection—Programme Search
Usually when you press the number buttons, the preset station is tuned in.
If the signals from the FM RDS preset station are not sufficient for good reception, this unit, using the AF data, tunes
in to another frequency broadcasting the same programme as the original preset station is broadcasting.
• The unit takes some time to tune in to another station using programme search.
• See also page 26.
10
Disc operations
Open the control panel and insert the disc.
Playback starts automatically.
To stop play and eject the disc
Change the display information
• Press SRC to listen to
another playback source.
Prohibiting disc ejection
1
*
If the file does not have Tag information or “TAG DISP” is set to
“TAG OFF” (see page 27), folder name and file name appear.
TAG indicator will not light up.
To cancel the prohibition, repeat the
same procedure.
2
*
“NO NAME” appears for an audio CD.
Pressing (or holding) the following buttons allows you to...
Disc type *3
(Number buttons) *4
Press: Select track
Hold: Reverse/fast-forward
track
Select folder
Locate particular folder
directly *5
Press: Select track
Hold: Reverse/fast-forward
track
Locate particular track directly
—
3
4
5
*
*
*
This unit can playback AAC files encoded using iTunes.
Press to select number 1 to 6; hold to select number 7 to 12.
It is required that folders be assigned with 2-digit numbers at the beginning of their folder names—01, 02, 03, and
so on.
Continued on the next page
OPERATIONS
11
After pressing
, press the following buttons to...
Disc type
Skip 10 tracks (within TRK RPT:
FLDR RND:
the same folder)
Repeat current track
FLDR RPT:
Repeat current folder
Randomly play all tracks of
current folder, then tracks of
next folders
DISC RND:
Randomly play all tracks
Skip 10 tracks
TRK RPT:
DISC RND:
Repeat current track
Randomly play all tracks
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
Listening to the USB device
You can connect a USB mass storage class device such as a USB memory, Digital Audio Player*1, portable HDD, etc. to
the unit.
1
*
You can connect both MTP (Media Transfer Protocol) devices and USB mass storage class devices.
Attaching a USB memory
USB input terminal
USB memory
This unit can play MP3/WMA/WMA-DRM10*1/AAC*2/WAV tracks stored in a USB device.
1
*
*
See page 32.
2
This unit can play back AAC files encoded using iTunes. This unit cannot play back AAC files purchased from iTunes
Store.
If a USB device has been attached...
Playback starts from where it has been stopped previously.
• If a different USB device is currently attached, playback starts from the beginning.
12
To stop play and detach the USB device
Straightly pull it out from the unit.
• Press SRC to listen to another playback source.
Cautions:
• Avoid using the USB device if it might hinder your safety driving.
• Do not pull out and attach the USB device repeatedly while “CHECK” is flashing on the display.
• Do not start the car engine if a USB device is connected.
• Stop play back before disconnecting a USB device.
• This unit may not be able to play the files depending on the type of USB device.
• You cannot connect a computer to the USB input terminal of the unit.
• Make sure all important data has been backed up to avoid losing the data.
• Do not leave a USB device in the car, expose to direct sunlight, or high temperature to avoid deformation or
cause damages to the device.
Pressing (or holding) the following buttons allows you to...
Press: Select track
Hold: Reverse/fast-forward track
Select folder
Locate particular folder directly
• See also *4 and *5 on page 11.
(Number buttons)
After pressing
, press the following buttons to...
Skip 10 tracks (within the same folder)
TRK RPT: Repeat current track
FLDR RPT: Repeat all tracks of current folder
FLDR RND: Randomly play all tracks of current folder, then tracks of next folders
DISC RND: Randomly play all tracks
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
Change the display information
* If the file does not have Tag information
or “TAG DISP” is set to “TAG OFF” (see
page 27), folder name and file name
appear. TAG indicator will not light up.
OPERATIONS
13
Using the Bluetooth® devices
For Bluetooth operations, it is required to connect the Bluetooth Adapter (KS-BTA200) to the CD changer jack on
the rear of this unit. See also page 23.
• Refer also to the instructions supplied with the Bluetooth adapter and the Bluetooth device.
• Refer to the list (included in the box) to see the countries where you may use the Bluetooth® function.
To use a Bluetooth device through the unit (“BT-PHONE” and “BT-AUDIO”) for the first time, you need to establish
Bluetooth wireless connection between the unit and the device.
• Once the connection is established, it is registered in the unit even if you reset your unit. Up to five devices can be
registered in total.
• Only one device can be connected at a time for each source (“BT-PHONE” and “BT-AUDIO”).
Registering a Bluetooth device
Registration (Pairing) methods
2 Select “NEW.”
Use either of the following items in the Bluetooth menu
to register and establish the connection with a device.
• Select “BT-PHONE” or “BT-AUDIO” as the source to
operate the Bluetooth menu.
3 Select “OPEN.”
OPEN
Make the unit ready to establish a new
Bluetooth connection.
Connection is established by operating the
Bluetooth device.
4 Enter a PIN (Personal Identification
Number) code to the unit.
SEARCH Make the unit ready to establish a new
Bluetooth connection.
• You can enter any number you like (1-digit to
16-digit number). [Initial: 0000]
Connection is established by operating
the unit.
* Some devices have their own PIN code. Enter the
specified PIN code to the unit.
1
Move to the next (or previous) number
position.
Registering using “OPEN”
Preparation
Operate the device to turn on its Bluetooth function.
2
Select a number or blank space.
1 Select “BT-PHONE” or “BT-AUDIO.”
3
4
Repeat steps 1 and 2 until you finish
entering a PIN code.
Confirm the entry.
“OPEN...” flashes on the display.
14
2
3
Select a device you want to connect.
Use “OPEN’ or “SEARCH’ to connect.
5 Use the Bluetooth device to search and
connect.
On the device to be connected, enter the same PIN
code you have just entered for this unit. “CONNECT”
flashes on the display.
Now connection is established and you can use the
device through the unit.
To connect/disconnect a registered device
1
Select “BT-PHONE” or “BT-AUDIO.”
The device remains registered even after you
disconnect the device. Use “CONNECT“ (or activate
“AUTO CNT”) to connect the same device from next
time. (See the right column and page 28.)
2
3
Select a registered device you want to
connect/disconnect.
To search for available devices
Perform steps 1 and 2 on page 14, then...
1
Select “SEARCH.”
The unit searches and displays the list of the
available devices.
• If no available device is detected, “UNFOUND”
appears.
Select “CONNECT” or “DISCNNCT” to connect/
disconnect the selected device.
2
3
4
Select a device you want to connect.
You can set the unit to connect a Bluetooth device
automatically when the unit is turned on. (See
“AUTO CNT” on page 28.)
Enter the specific PIN code of the device to
the unit.
• Refer to the instructions supplied with the device
to check the PIN code.
Use the Bluetooth device to connect.
Now connection is established and you can use the
device through the unit.
To delete a registered device
1
Select “BT-PHONE” or “BT-AUDIO.”
To connect a special device
Perform steps 1 and 2 on page 14, then...
2
3
Select a registered device you want to delete.
1
Select “SPECIAL.”
The unit displays the list of the preset devices.
Select “DELETE,” then “YES” to delete the
selected device.
EXTERNAL DEVICES 15
Using the Bluetooth cellular phone
Change the display information
~ Select “BT-PHONE.”
Ÿ Enter Bluetooth menu.
! Make a call or settings using the Bluetooth menu. (See pages 17 and 28.)
When a call comes in....
When an SMS comes in....
The source is automatically changed to “BT-PHONE.”
If the cellular phone is compatible with SMS (Short
Message Service) and “MSG-INFO” (message info) is set
to “AUTO” (see page 28), the unit rings and “RCV MSG”
(receiving message) appears on the display to inform
you the arrival of the message.
When “AUTO ANS” (answer) is activated....
The unit answers the incoming calls automatically, see
page 28.
• When “AUTO ANS” (answer) is deactivated, press any
button (except
incoming call.
/control dial) to answer the
To end the call
Hold any button (except
/control dial).
• You can adjust the microphone volume level (see
page 28).
16
Making a call
You can make a call using the following methods.
Select “BT-PHONE,” then follow the following steps to make a call:
1
2
3(unless mentioned otherwise)
Call history
Phone book
Direct dialing
Display the Dial Select a call history.
Select a name (if it is acquired) or
phone number.
Menu.
REDIAL, RECEIVED, MISSED
Select “PH BOOK.”
The list of phone number appears.
Select a name from the list.
Select “NUMBER.”
Enter the phone number.
Voice command
1
“SAY NAME” appears on the display.
2 Speak the name you want to call.
• You can also use voice command from the Dial Menu. Select “VOICE” from the Dial Menu.
• If your cellular phone does not support the voice recognition system, “ERROR” appears on the
display.
Preset phone
number
See the following for settings.
Presetting the phone number
You can preset up to six phone numbers.
1 Display the Dial Menu.
3 Select a phone number.
4
2 Select “PH BOOK,“ “MISSED,” or
“RECEIVED” whichever you want to use.
EXTERNAL DEVICES 17
Using the Bluetooth audio player
Enter setting menu
(Device list)
Pause/start play back
Reverse skip/forward skip
Change the display information
~ Select “BT-AUDIO.”
If playback did not start automatically, operate the Bluetooth audio player to start playback.
• Refer also to page 15 for connecting/disconnecting/deleting a registered device.
Bluetooth Information:
If you wish to receive more information about Bluetooth, visit our JVC web site.
Listening to the CD changer
Change the display information
(see page 11)
It is recommended to use a JVC MP3-compatible CD changer with your unit. You can connect a CD changer to the CD
changer jack on the rear of the unit. See also page 23.
• You can only play conventional CDs (including CD Text) and MP3 discs.
18
Preparation
Make sure “CHANGER” is selected for the external input setting, see page 27.
~ Select “CD-CH.”
Ÿ Select a disc to start playing.
Press: For selecting disc number 1 – 6.
Hold: For selecting disc number 7 – 12.
Pressing (or holding) the following buttons allows you to...
Disc type
Press: Select track
Hold: Reverse/fast-forward track
Select folder
—
Press: Select track
Hold: Reverse/fast-forward track
After pressing
, press the following buttons to...
Disc type
Skip 10 tracks (within TRK RPT:
FLDR RND:
the same folder)
Repeat current track
FLDR RPT:
Randomly play all tracks of
current folder, then tracks of
Repeat all tracks of current folder next folders
DISC RPT:
DISC RND:
Repeat all tracks of the current
disc
Randomly play all tracks of
current disc
MAG RND:
Randomly play all tracks of the
inserted discs
Skip 10 tracks
TRK RPT:
DISC RND:
Repeat current track
DISC RPT:
Randomly play all tracks of
current disc
Repeat all tracks of the current MAG RND:
disc Randomly play all tracks of the
inserted discs
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
EXTERNAL DEVICES 19
Listening to the DAB tuner
Select preset service.
Change the display information
You can connect a JVC DAB tuner to the CD changer jack on the rear of the unit. See also page 23.
~ Select “DAB.”
Ÿ Select the bands.
! Searching for an ensemble.
Manual Search: Hold either one of the buttons until “MANU” flashes on the display, then press it repeatedly.
⁄ Select a service (either primary or secondary) to listen to.
Storing DAB services in memory
While listening to a DAB service...
Tracing the same programme—
Alternative Frequency Reception
• While receiving a DAB service:
When driving in an area where a service cannot be
received, this unit automatically tunes in to another
ensemble or FM RDS station, broadcasting the same
programme.
• While receiving an FM RDS station:
When driving in an area where a DAB service is
broadcasting the same programme as the FM RDS
station is broadcasting, this unit automatically tunes
in to the DAB service.
Activating/deactivating TA/PTY
Standby Reception
• Operations are exactly the same as explained on page
10 for FM RDS stations.
• You cannot store PTY codes separately for the DAB
tuner and for the FM tuner.
To deactivate the Alternative Frequency
Reception, see page 27.
20
Listening to the iPod / D. player
Change the display information
Before operating, connect either one of the following (separately purchased) to the CD changer jack on the rear of
the unit. See also page 23.
• Interface adapter for iPod—KS-PD100 for controlling an iPod.
• D. player interface adapter—KS-PD500 for controlling a D. player.
Preparation
Make sure “CHANGER” is selected for the external input setting, see page 27.
~ Select “IPOD” or “D. PLAYER.”
Ÿ Select a song to start playing.
Selecting a track from the menu
1 Enter the main menu.
3 Confirm the selection.
This mode will be canceled if no
operations are done for about
5 seconds.
• To move back to the previous menu, press 5.
• If a track is selected, playback starts
automatically.
2 Select the desired menu.
• Holding 4/¢ can skip 10 items at
a time.
For iPod:
Pause/stop playback
• To resume playback, press
the button again.
PLAYLIST Ô ARTISTS Ô ALBUMS Ô SONGS
Ô GENRES Ô COMPOSER Ô (back to the
beginning)
Press: Select tracks
Hold: Reverse/fast-forward
track
For D. player:
PLAYLIST Ô ARTIST Ô ALBUM Ô GENRE
Ô TRACK Ô (back to the beginning)
Continued on the next page
EXTERNAL DEVICES 21
After pressing
, press the following buttons to...
ONE RPT:
Functions the same as “Repeat One” of the iPod or “Repeat Mode =
One” of the D. player.
ALL RPT:
Functions the same as “Repeat All” of the iPod or “Repeat Mode =
All” of the D. player.
ALBM RND*:
Functions the same as “Shuffle Albums” of the iPod.
SONG RND/RND ON: Functions the same as “Shuffle Songs” of the iPod or “Random Play
= On” of the D. player.
• To cancel repeat play or random play, select “RPT OFF” or “RND OFF.”
* iPod: Functions only if you select “ALL” in “ALBUMS” of the main “MENU.”
Listening to the other external components
Change the display information
You can connect an external component using the following adapters (separately purchased) to the CD changer jack
on the rear of the unit. See also page 23.
• Line Input Adapter—KS-U57
• AUX Input Adapter—KS-U58
Preparation
Make sure “EXT IN” is selected for the external input setting, see page 27.
~ Select “EXT IN.”
Ÿ Turn on the connected component and start playing the source.
! Adjust the volume.
⁄ Adjust the sound as you want (see pages 24 and 25).
22
Concept diagram of the external device connection
For connection, see Installation/Connection manual (separate volume).
• Connection 1 (integrated connection)
Unit
CD changer jack
JVC CD changer, [18]
Apple iPod, [21]
(see page 27 of the
”EXT IN” setting)
(see pages 14 – 18)
or
JVC D. player, [21]
MD player, etc., [22]
MD player, etc., [22]
JVC DAB tuner, [20]
(see page 27 of the
”EXT IN” setting)
• Connection 2 (alternative connection)
Unit
CD changer jack
(see pages 14 – 18)
JVC DAB tuner, [20]
JVC CD changer, [18]
Apple iPod, [21]
(see page 27 of the
”EXT IN” setting)
JVC D. player, [21]
MD player, etc., [22]
MD player, etc., [22]
(see page 27 of the
”EXT IN” setting)
:
Adapter (separately purchased)
EXTERNAL DEVICES 23
Selecting a preset sound mode
Preset values
BAS
MID
TRE
LOUD
(bass)
(mid-range)
(treble)
(loudness)
Indication (For)
USER (Flat sound)
00
00
00
OFF
ROCK
(Rock
(Classical
or
disco
music)
+01
+0300
+03OFF
CLASSIC
music)
+02
00
POPS (Light music)
+01
–02
+02
+01
OFF
ON
HIP HOP (Funk or rap music)
+04
JAZZ
(Jazz
music)
+0300
+03OFF
24
Adjusting the sound
1
General settings—PSM
You can change PSM (Preferred Setting Mode) items
listed in the table on pages 26 and 27.
2 Adjust the level.
1 Enter the PSM settings.
BAS *1 (bass)
Adjust the bass.
MID *1 (mid-range)
Adjust the mid-range frequencies
sound level.
–06 to +06
–06 to +06
2 Select a PSM item.
3 Select or adjust the selected PSM item.
TRE *1 (treble)
Adjust the treble.
FAD *2 (fader)
–06 to +06
R06 to F06
Adjust the front and rear speaker
balance.
BAL *3 (balance)
Adjust the left and right speaker
balance.
LOUD *1 (loudness)
Boost low and high frequencies to
produce a well-balanced sound at low
volume level.
4 Repeat steps 2 and 3 to adjust other PSM
L06 to R06
items if necessary.
5 Finish the procedure.
LOUD ON or
LOUD OFF
SUB.W (subwoofer)
Adjust the subwoofer output level.
00 to 08,
initial: 04
VOL (volume)
Adjust the volume.
00 to 30
(or 50) *4
1
*
When you adjust the bass, mid-range, treble, or
loudness, the adjustment you have made is stored
for the currently selected sound mode (iEQ) including
“USER.”
If you are using a two-speaker system, set the fader
level to “00.”
The adjustment will not affect the subwoofer output.
Depending on the amplifier gain control setting. (See
page 27 for details.)
2
*
3
4
*
*
Continued on the next page
SETTINGS 25
Indication
Item
Setting, [reference page]
(
: Initial)
DEMO
Display demonstration
• DEMO ON
:
Display demonstration will be activated automatically if no
operation is done for about 20 seconds, [4].
Cancels.
• DEMO OFF
:
:
CLK DISP *1
Clock display
• ON
Clock time is shown on the display at all times when the power is
turned off.
• OFF
:
:
:
:
:
Cancels; pressing D DISP will show the clock time for about 5 seconds
when the power is turned off, [4].
CLOCK H
Hour adjustment
0 – 23 (1 – 12)
00 – 59
Initial: 0 (0:00), [4].
CLOCK M
Minute adjustment
Initial: 00 (0:00), [4].
See also page 4 for setting.
24H/12H
Time display mode
• 12H
• 24H
CLK ADJ
• AUTO
The built-in clock is automatically adjusted using the CT (clock time)
Clock adjustment
data in the RDS signal.
Cancels.
• OFF
:
:
AF-REG *2
• AF
When the currently received signals become weak, the unit switches
to another station or service (the programme may differ from the
one currently received), [10].
When the currently received signals become weak, the unit switches
to another station broadcasting the same programme.
Cancels (not selectable when “DAB AF” is set to “AF ON”).
Alternative frequency/
regionalization
reception
• AF REG
:
• OFF
:
:
PTY-STBY
OFF, PTY codes
Activates PTY Standby Reception with one of the PTY codes, [9, 10].
PTY standby
(see page 9)
TA VOL
VOL 00 —
:
Initial: VOL 15, [10].
Traffic announcement VOL 30 or 50 *3
volume
P-SEARCH *2
Programme search
• ON
• OFF
:
:
Activates Programme Search, [10].
Cancels.
1
*
If the power supply is not interrupted by turning off the ignition key of your car, it is recommended to select “OFF” to
save the car’s battery.
Only for RDS FM stations.
Depending on the “AMP GAIN” setting.
2
3
*
*
26
Indication
Item
Setting, [reference page]
(
: Initial)
DAB AF *4
• AF ON
:
Traces the programme among DAB services and FM RDS stations,
Alternative frequency
reception
[20].
Cancels.
• AF OFF
:
:
DAB VOL *4
DAB volume
adjustment
VOL –12
— VOL +12
Initial: VOL 00; You can adjust the volume level of DAB tuner to
match the FM sound level and store it in memory.
DIMMER
Dimmer
• AUTO
• ON
• OFF
:
:
:
Dims the display when you turn on the headlights.
Dims the display illumination.
Cancels.
TEL
• MUTING 1/
MUTING 2
• OFF
:
:
Select either one which mutes the sounds while using a cellular
phone.
Cancels.
Telephone muting
SCROLL *5
Scroll
• ONCE
• AUTO
• OFF
:
:
:
Scrolls the track information once.
Repeats scrolling (at 5-second intervals).
Cancels. (Holding D DISP can scroll the display regardless of the
setting.)
WOOFER
Subwoofer cutoff
frequency
• LOW
• MID
• HIGH
:
:
:
Frequencies lower than 90 Hz are sent to the subwoofer.
Frequencies lower than 135 Hz are sent to the subwoofer.
Frequencies lower than 180 Hz are sent to the subwoofer.
EXT IN *6
External input
• CHANGER
• EXT IN
:
:
To use a JVC CD changer, [18], or an Apple iPod/a JVC D. player, [21].
To use any other external component, [22].
TAG DISP
Tag display
• TAG ON
• TAG OFF
:
:
Shows the tag while playing MP3/WMA/AAC/WAV tracks.
Cancels.
AMP GAIN
Amplifier gain control
• LOW PWR
:
VOL 00 – VOL 30 (Select if the maximum power of each speaker is
less than 50 W to prevent damaging the speaker.)
VOL 00 – VOL 50
• HIGH PWR
:
:
IF BAND
Intermediate
frequency band
• AUTO
Increases the tuner selectivity to reduce interference noises between
adjacent stations. (Stereo effect may be lost.)
Subject to interference noises from adjacent stations, but sound
quality will not be degraded and the stereo effect will remain.
• WIDE
:
4
*
*
*
Displayed only when DAB tuner is connected.
Some characters or symbols will not be shown correctly (or will be blanked) on the display.
Displayed only when one of the following sources is selected—FM, AM, DAB, CD, USB, or Bluetooth.
5
6
SETTINGS 27
Bluetooth settings
You can change the settings listed on the right column
according to your preference.
Setting menu ( : Initial)
AUTO CNT (connect)
When the unit is turned on, the connection is
established automatically with....
1 Select “BT-PHONE” or “BT-AUDIO.”
OFF:
No Bluetooth device.
LAST:
The last connected Bluetooth device.
ORDER: The available registered Bluetooth device
found at first.
2 Enter the Bluetooth menu.
AUTO ANS (answer)
Only for the device being connected for “BT-PHONE.”
ON:
The unit answers the incoming calls
automatically.
3 Select “SETTING.”
OFF:
The unit does not answer the calls
automatically. Answer the calls manually.
REJECT: The unit rejects all incoming calls.
4 Select a setting item.
MSG-INFO (message info)
Only for the device being connected for “BT-PHONE.”
AUTO: The unit informs you of the arrival of
a message by ringing and displaying
“RCV MSG” (receiving message).
MANUAL: The unit does not inform you of the arrival of
a message.
5 Change the setting accordingly.
MIC SET (microphone setting)
Only for the device being connected for “BT-PHONE.”
Adjust microphone volume connected to the Bluetooth
adapter, [LEVEL 01/02/03].
VERSION
The Bluetooth software and hardware versions are
shown.
28 SETTINGS
Maintenance
How to clean the connectors
To keep discs clean
Frequent detachment will deteriorate the connectors.
To minimize this possibility, periodically wipe the
connectors with a cotton swab or cloth moistened with
alcohol, being careful not to damage the connectors.
A dirty disc may not play correctly.
If a disc does become dirty, wipe it with
a soft cloth in a straight line from center
to edge.
• Do not use any solvent (for example, conventional
record cleaner, spray, thinner, benzine, etc.) to clean
discs.
To play new discs
New discs may have some rough spots
around the inner and outer edges. If
such a disc is used, this unit may reject
the disc.
To remove these rough spots, rub the edges with a
pencil or ball-point pen, etc.
Connector
Moisture condensation
Moisture may condense on the lens inside the unit in
the following cases:
• After starting the heater in the car.
• If it becomes very humid inside the car.
Should this occur, the unit may malfunction. In this
case, eject the disc and leave the unit turned on for a
few hours until the moisture evaporates.
Do not use the following discs:
Warped disc
Sticker
How to handle discs
Sticker residue
Center holder
When removing a disc from its
case, press down the center holder
of the case and lift the disc out,
holding it by the edges.
Stick-on label
Unusual shape
• Always hold the disc by the edges. Do not touch its
recording surface.
When storing a disc into its case, gently insert the
disc around the center holder (with the printed surface
facing up).
Single CD (8 cm disc)
• Make sure to store discs into the cases after use.
REFERENCES 29
More about this unit
General
Disc
Turning on the power
Caution for DualDisc playback
• By pressing SRC on the unit, you can also turn on the
power. If the source is ready, playback also starts.
• The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc on
this product may not be recommended.
Turning off the power
• If you turn off the power while listening to a disc, disc
play will start from where playback has been stopped
previously, next time you turn on the power.
General
• This unit has been designed to reproduce CDs/CD
Texts, and CD-Rs (Recordable)/CD-RWs (Rewritable)
in audio CD (CD-DA), MP3/WMA/AAC formats.
• When a disc is inserted upside down, “PLEASE” and
“EJECT” appear alternately on the display. Press 0 to
eject the disc.
FM/AM/RDS
Storing stations in memory
• During SSM search...
– Received stations are preset in No. 1 (lowest
frequency) to No. 6 (highest frequency).
– When SSM is over, the station stored in No. 1 will
be automatically tuned in.
• When storing stations, the previously preset stations
are erased and stations are stored newly.
• While fast-forwarding or reversing on an MP3/WMA/
AAC disc, you can only hear intermittent sounds.
Ejecting a disc
• If the ejected disc is not removed within 15 seconds,
the disc is automatically inserted again into the
loading slot to protect it from dust. Playback starts
automatically.
FM RDS operations
• Network-Tracking Reception requires two types of
RDS signals—PI (Programme Identification) and AF
(Alternative Frequency) to work correctly. Without
receiving these data correctly, Network-Tracking
Reception will not operate correctly.
• If a Traffic Announcement is received by TA Standby
Reception, the volume level automatically changes to
the preset level (TA VOL) if the current level is lower
than the preset level.
• When Alternative Frequency Reception is activated
(with AF selected), Network-Tracking Reception is
also activated automatically. On the other hand,
Network-Tracking Reception cannot be deactivated
without deactivating Alternative Frequency
Reception. (See pages 26 and 27.)
• After ejecting a disc, “NO DISC” appears and you
cannot operate some of the buttons. Insert another
disc or press SRC to select another playback source.
Playing a CD-R or CD-RW
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can play back only files of the same type
which are first detected if a disc includes both audio
CD (CD-DA) files and MP3/WMA/AAC files.
• This unit can play back multi-session discs; however,
unclosed sessions will be skipped while playing.
• Some CD-Rs or CD-RWs may not play back on this
unit because of their disc characteristics, or for the
following reasons:
• If you want to know more about RDS, visit
<http://www.rds.org.uk>.
30
– Discs are dirty or scratched.
– Moisture condensation occurs on the lens inside
the unit.
– The pickup lens inside the unit is dirty.
– CD-R/CD-RW on which the files are written with
“Packet Write” method.
– There are improper recording conditions (missing
data, etc.) or media conditions (stained, scratched,
warped, etc.).
– Bit rate of AAC: 16 kbps — 320 kbps
– Sampling frequency of AAC: 48 kHz, 44.1 kHz
– Disc format: ISO 9660 Level 1/Level 2, Romeo,
Joliet, Windows long file name
• The maximum number of characters for file/folder
names vary among the disc format used (includes
4 extension characters—<.mp3>, <.wma>, or
<.m4a>).
– ISO 9660 Level 1: up to 12 characters
– ISO 9660 Level 2: up to 31 characters
– Romeo*: up to 128 (60) characters
– Joliet*: up to 64 (30) characters
• CD-RWs may require a longer readout time since the
reflectance of CD-RWs is lower than that of regular
CDs.
• Do not use the following CD-Rs or CD-RWs:
– Discs with stickers, labels, or a protective seal stuck
to the surface.
– Discs on which labels can be directly printed by an
ink jet printer.
Using these discs under high temperatures or high
humidities may cause malfunctions or damage to the
unit.
– Windows long file name*: up to 128 (60)
characters
* The parenthetic figure is the maximum number of
characters for file/folder names in case the total
number of files and folders is 271 or more.
• This unit can recognize a total of 512 files, of 200
folders, and of 8 hierarchies.
• This unit can play back files recorded in VBR (variable
bit rate).
Files recorded in VBR have a discrepancy in elapsed
time display, and do not show the actual elapsed
time. Especially, after performing the search function,
this difference becomes noticeable.
• This unit cannot play back the following files:
– MP3 files encoded with MP3i and MP3 PRO format.
– MP3 files encoded in an inappropriate format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded with lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media® Audio.
– WMA files copy-protected with DRM.
– AAC files created by any other application than
iTunes.
Playing an MP3/WMA/AAC disc
• This unit can play back MP3/WMA/AAC files with
the extension code <.mp3>, <.wma>, or <.m4a>
(regardless of the letter case—upper/lower).
• This unit can show the names of albums, artists
(performer), ID3 Tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4)
for MP3, and show WMA/AAC Tag.
• This unit can display only one-byte characters. No
other characters can be correctly displayed.
• This unit can play back MP3/WMA/AAC files meeting
the conditions below:
– Bit rate of MP3: 8 kbps — 320 kbps
– Sampling frequency of MP3:
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
12 kHz, 11.025 kHz, 8 kHz (for MPEG-2.5)
– Bit rate of WMA: 16 kbps — 32 kbps
(Sampling frequency: 22.05 kHz)
– AAC files encoded with Apple lossless format.
– Files which have the data such as AIFF, ATRAC3,
etc.
• The search function works but search speed is not
constant.
32 kbps — 320 kbps
(Sampling frequency: 48 kHz,
44.1 kHz, 32 kHz)
Continued on the next page
REFERENCES 31
WAV:
Playing MP3/WMA/AAC/WAV tracks from a USB
device
• Connecting a USB device automatically changes the
source to “USB.”
• While playing from a USB device, the playback order
may differ from other players.
• This unit may be unable to play back some USB
devices or some files due to their characteristics or
recording conditions.
• Depending on the shape of the USB devices and
connection ports, some USB devices may not be
attached properly or the connection might be loose.
• When connecting a USB mass storage class device,
refer also to its instructions.
– Bit rate: Linear PCM at 705 kbps and 1 411 kbps
– Sampling frequency: 44.1 kHz
– Channel: 1 ch/2 ch
• This unit can play back MP3 files recorded in VBR
(variable bit rate).
• The maximum number of characters for folder and
file names is 25 characters; 128 characters for MP3/
WMA/AAC/WAV Tag.
• This unit can recognize a total of 50 000 files and
5 000 folders (999 files per folder). However, the
display can shows until 9 999 folders/files.
• The unit cannot recognize a USB mass storage class
device whose rating is other than 5 V and does not
exceed 500 mA.
• This unit may not recognized a USB device connected
through a USB card reader.
• This unit may not play back files in a USB device
properly when using a USB extension cord.
• This unit cannot assure proper functions or supply
power to all types of USB devices.
• This unit cannot play back the following files:
– MP3 files encoded with MP3i and MP3 PRO format.
– MP3 files encoded in an inappropriate format.
– MP3 files encoded with Layer 1/2.
– WMA files encoded with lossless, professional, and
voice format.
– WMA files which are not based upon Windows
Media® Audio.
– AAC files created by any other application than
iTunes.
• Connect one USB mass storage class device to the unit
at a time. Do not use a USB hub.
• You can connect two types of USB device to this
unit—MTP device and Mass storage class device.
If you connect an MTP device featuring “USB digital
media streaming” to this unit (except JVC D. Player
XA-HD500), you can play back the WMA-DRM10
(Digital Right Management) files purchased through
the music distributing web sites, through this unit.
• This unit is compatible with the USB Full-Speed.
• If the connected USB device does not have the correct
files, “NO FILE” appears.
• This unit can show ID3 Tag (Version 1.0, 1.1, 2.2, 2.3,
or 2.4) for MP3 and show WMA/AAC/WAV Tag.
• This unit can play back MP3/WMA/AAC/WAV files
meeting the conditions below:
MP3:
– AAC files encoded with Apple lossless format.
– WAV files encoded using MS-ADPCM.
– Files which have the data such as AIFF, ATRAC3,
etc.
– Bit rate: 8 kbps — 320 kbps
– Sampling frequency:
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
WMA:
Changing the source
– Bit rate: 5 kbps — 320 kbps
• If you change the source, playback also stops.
Next time you select the same source again, playback
starts from where it has been stopped previously.
– Sampling frequency: 8 kHz — 48 kHz
– Channel: Mono/stereo
AAC:
– Bit rate: 16 kbps — 320 kbps
– Sampling frequency: 48 kHz — 44.1 kHz
– Channel: 1 ch/2 ch
32
Detaching a USB device
DAB
• After removing a USB device, “NO USB“ appears and
you cannot operate some of the buttons. Reattach a
USB device or press SRC to select another playback
source.
• Only the primary DAB service can be preset even
when you store a secondary service.
• A previously preset DAB service is erased when a new
DAB service is stored in the same preset number.
Bluetooth operations
General
• While driving, do not perform complicated operation
such as dialing the numbers, using phone book, etc.
When you perform these operations, stop your car in
a safe place.
iPod or D. player
• When you turn on this unit, the iPod or D. player is
charged through this unit.
• While the iPod or D. player is connected, all
operations from the iPod or D. player are disabled.
Perform all operations from this unit.
• The text information may not be displayed correctly.
• If the text information includes more than 8
characters, it scrolls on the display. This unit can
display up to 40 characters.
• Some Bluetooth devices may not be connected to
this unit depending on the Bluetooth version of the
device.
• This unit may not work for some Bluetooth devices.
• Connecting condition may vary depending on the
circumstances around you.
Notice:
When operating an iPod or a D. player, some
operations may not be performed correctly or as
intended. In this case, visit the following JVC web
site:
For iPod users: <http://www.jvc.co.jp/english/
car/support/ks-pd100/index.html>
For D. player users: <http://www.jvc.co.jp/
english/car/support/ks-pd500/index.html>
• When the unit is turned off, the device is
disconnected.
Warning messages for Bluetooth operations
ERR CNCT
The device is registered but the
(Error
connection has failed. Use “CONNECT”
Connection) to connect the device again. (See page
15.)
ERROR
Try the operation again. If “ERROR”
appears again, check if the device
supports the function you have tried.
General settings—PSM
• “AUTO” setting for “DIMMER” may not work correctly
on some vehicles, particularly on those having a
control dial for dimming.
In this case, change the “DIMMER” setting to any
other than “AUTO.”
• If you change the “AMP GAIN” setting from
“HIGH PWR” to “LOW PWR” while the volume level
is set higher than “VOL 30,” the unit automatically
changes the volume level to “VOL 30.”
UNFOUND
LOADING
WAIT
No available Bluetooth device is
detected by “SEARCH.”
The unit is updating the phone book
and/or text messages.
The unit is preparing to use the
Bluetooth function. If the message does
not disappear, turn off and turn on the
unit, then connect the device again (or
reset the unit).
RESET 8
Check the connection between the
adapter and this unit.
REFERENCES 33
Troubleshooting
What appears to be trouble is not always serious. Check the following points before calling a service center.
Symptom
Remedy/Cause
• Sound cannot be heard from the speakers.
• Adjust the volume to the optimum level.
• Check the cords and connections.
• The unit does not work at all.
Reset the unit (see page 2).
Store stations manually.
Connect the aerial firmly.
Insert the disc correctly.
• SSM automatic presetting does not work.
• Static noise while listening to the radio.
• Disc cannot be played back.
• CD-R/CD-RW cannot be played back.
• Insert a finalized CD-R/CD-RW.
• Tracks on the CD-R/CD-RW cannot be skipped. • Finalize the CD-R/CD-RW with the component which
you used for recording.
• Disc can neither be played back nor ejected.
• Unlock the disc (see page 11).
• Eject the disc forcibly (see page 2).
• Disc sound is sometimes interrupted.
• Stop playback while driving on rough roads.
• Change the disc.
• Check the cords and connections.
• “NO DISC” appears on the display.
Insert a playable disc into the loading slot.
• “PLEASE” and “EJECT” appear alternately on
the display.
This occurs sometimes due to over-heating. Eject the disc
or change to another playback source.
• Disc cannot be played back.
• Use a disc with MP3/WMA/AAC tracks recorded in
the format compliant with ISO 9660 Level 1, Level 2,
Romeo, or Joliet.
• Add the extension code <.mp3>, <.wma>, or
<.m4a> to the file names.
• Noise is generated.
Skip to another track or change the disc. (Do not add
the extension code <.mp3>, <.wma>, or <.m4a> to
non-MP3/WMA/AAC tracks.)
• A longer readout time is required (“CHECK”
keeps flashing on the display).
Do not use too many hierarchies and folders.
34
Symptom
Remedy/Cause
• Tracks do not play back in the order you have Playback order is determined when files are recorded.
intended them to play.
• Elapsed playing time is not correct.
This sometimes occurs during play. This is caused by how
the tracks are recorded on the disc.
• “PLEASE” and “EJECT” appear alternately on Insert a disc that contains MP3/WMA/AAC tracks.
the display.
• Correct characters are not displayed (e.g.
album name).
This unit can only display letters (upper case), numbers,
and a limited number of symbols.
• Noise is generated.
The track played back is not an MP3/WMA/AAC/WAV
track. Skip to another file. (Do not add the extension code
<.mp3>, <.wma>, <.m4a>, or <.wav> to non-MP3/
WMA/AAC/WAV tracks.)
• “CHECK” keeps flashing on the display.
• Readout time varies depending on the USB device.
• Do not use too many hierarchy, folders, and empty
folders*.
• Turn off the power then on again.
* Folder that is physically empty or folder that contains
data but does not contain valid MP3/WMA/AAC/WAV
track.
• “NO FILE” flashes on the display.
• “NO USB” appears on the display.
Attach a USB device that contains tracks encoded in an
appropriate format.
• “READ” and “FAILED” appear alternately on
the display.
The total number of tracks could not be accessed properly.
• Correct characters are not displayed (e.g.
album name).
This unit can only display letters (upper case), numbers,
and a limited number of symbols.
• While playing a track, sound is sometimes
interrupted.
MP3/WMA/AAC/WAV tracks have not been properly
copied into the USB device.
Copy MP3/WMA/AAC/WAV tracks again into the USB
device, and try again.
Continued on the next page
REFERENCES 35
Symptom
Remedy/Cause
• Bluetooth device does not detect the unit.
The unit can be connected with one Bluetooth cellular
phone and one Bluetooth audio device at a time.
While connecting a device, this unit cannot be detected
from another device. Disconnect currently connected
device and search again.
• The unit does not detect the Bluetooth device. • Check the Bluetooth setting of the device.
• Search from the Bluetooth device. After the device
detects the unit, select “OPEN” on the unit to connect
the device. (See page 14.)
• The unit does not make pairing with the
Bluetooth device.
• Enter the same PIN code for both the unit and target
device.
• Select the device name from “SPECIAL,” then try to
connect again. (See page 15.)
• Echo or noise occurs.
Adjust the microphone unit position.
• Phone sound quality is poor.
• Reduce the distance between the unit and the
Bluetooth audio device.
• Move the car to a place where you can get a better
signal reception.
• The sound is interrupted or skipped during
playback of a Bluetooth audio device.
• Reduce the distance between the unit and the
Bluetooth audio device.
• Disconnect the device connected for “BT-PHONE.”
• Turn off, then turn on the unit.
• (When the sound is not yet restored,) connect the
device again.
• The connected audio device cannot be
controlled.
Check whether the connected audio device supports
AVRCP (Audio Video Remote Control Profile).
• “NO DISC” appears on the display.
• “NO MAG” appears on the display.
• “RESET 8” appears on the display.
Insert a disc into the magazine.
Insert the magazine.
Connect this unit and the CD changer correctly and press
the reset button of the CD changer.
• “RESET 1” – “RESET 7” appears on the display. Press the reset button of the CD changer.
• The CD changer does not work at all. Reset the unit (see page 2).
* For Bluetooth operations, refer also to the instructions supplied with the Bluetooth Adapter.
36
Symptom
Remedy/Cause
• “noSIGNAL” appears on the display.
• “RESET 08” appears on the display.
Move to an area with stronger signals.
Connect this unit and the DAB tuner correctly and reset
the unit (see page 2).
• The DAB tuner does not work at all.
• “ANTENANG” appears on the display.
Reconnect this unit and the DAB tuner correctly. Then,
reset the unit (see page 2).
Check the cords and connections.
• The iPod or D. player does not turn on or does • Check the connecting cable and its connection.
not work.
• Update the firmware version.
• Charge the battery.
• The sound is distorted.
Deactivate the equalizer either on this unit or the
iPod/D. player.
• “NO IPOD” or “NO DP” appears on the display. • Check the connecting cable and its connection.
• Charge the battery.
• Playback stops.
The headphones are disconnected during playback.
Restart the playback operation (see page 21).
• No sound can be heard when connecting an
iPod nano.
• Disconnect the headphones from the iPod nano.
• Update the firmware version of the iPod nano.
• No sound can be heard.
• “ERROR 01” appears on the display when
connecting a D. player.
Disconnect the adapter from the D. player. Then, connect
it again.
• “NO FILE” or “NO TRACK” appears on the
display.
No tracks are stored. Import tracks to the iPod or D. player.
• “RESET 1” – “RESET 7” appears on the display. Disconnect the adapter from both the unit and iPod/
D. player. Then, connect it again.
• “RESET 8” appears on the display.
Check the connection between the adapter and this unit.
• The iPod’s or D. player’s controls do not work Reset the iPod or D. player.
after disconnecting from this unit.
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
• iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.
• The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Victor
Company of Japan, Limited (JVC) is under license. Other trademarks and trade names are those of their respective
owners.
REFERENCES 37
Specifications
AUDIO AMPLIFIER SECTION
Maximum Power Output:
Front and rear:
50 W per channel
Continuous Power Output (RMS): Front and rear:
19 W per channel into 4 Ω, 40 Hz to 20 000 Hz at no more
than 0.8% total harmonic distortion.
Load Impedance:
4 Ω (4 Ω to 8 Ω allowance)
12 dB at 60 Hz
Tone Control Range:
Bass:
Mid-range:
Treble:
12 dB at 1 kHz
12 dB at 10 kHz
Frequency Response:
40 Hz to 20 000 Hz
70 dB
Signal-to-Noise Ratio:
Line-Out Level/Impedance:
Output Impedance:
2.5 V/20 kΩ load (full scale)
1 kΩ
Subwoofer-Out Level/Impedance:
Other Terminal:
2.5 V/20 kΩ load (full scale)
CD changer, USB input terminal, steering wheel remote
input
TUNER SECTION
Frequency Range:
FM:
AM:
87.5 MHz to 108.0 MHz
(MW) 522 kHz to 1 620 kHz
(LW) 144 kHz to 279 kHz
FM Tuner
Usable Sensitivity:
50 dB Quieting Sensitivity:
11.3 dBf (1.0 μV/75 Ω)
16.3 dBf (1.8 μV/75 Ω)
65 dB
Alternate Channel Selectivity (400 kHz):
Frequency Response:
Stereo Separation:
MW Tuner
40 Hz to 15 000 Hz
30 dB
Sensitivity:
20 μV
35 dB
Selectivity:
LW Tuner
Sensitivity:
50 μV
38
CD PLAYER SECTION
Type:
Compact disc player
Non-contact optical pickup (semiconductor laser)
2 channels (stereo)
Signal Detection System:
Number of Channels:
Frequency Response:
5 Hz to 20 000 Hz
Dynamic Range:
96 dB
Signal-to-Noise Ratio
98 dB
Wow and Flutter:
Less than measurable limit
Max. Bit Rate: 320 kbps
Max. Bit Rate: 320 kbps
Max. Bit Rate: 320 kbps
MP3 Decoding Format: (MPEG1/2 Audio Layer 3)
WMA (Windows Media® Audio) Decoding Format:
AAC (Advanced Audio Coding) Decoding Format:
USB SECTION
USB Standard:
USB 1.1
Data Transfer Rate:
Full Speed:
Low Speed:
Max. 12 Mbytes
Max. 1.5 Mbytes
Mass storage class, MTP
FAT 12/16/32
Compatible Device:
Compatible File System:
Playable Audio Format:
Max. Current:
MP3/WMA/AAC/WAV
500 mA
GENERAL
Power Requirement:
Grounding System:
Operating Voltage:
DC 14.4 V (11 V to 16 V allowance)
Negative ground
Allowable Operating Temperature:
0°C to +40°C
Dimensions (W × H × D):
(approx.)
Installation Size:
Panel Size:
182 mm × 52 mm × 158 mm
188 mm × 58 mm × 12 mm
1.4 kg (excluding accessories)
Mass:
Design and specifications are subject to change without notice.
REFERENCES 39
|