JVC 0709DTSMDTJEIN User Manual

Thank you for purchasing a JVC product.  
Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best  
possible performance from the unit.  
KD-S16  
CD RECEIVER: INSTRUCTIONS/INSTALLATION  
Installation/connection are explained at the last section of this manual (reverse page, indicated with  
symbol).  
For customer Use:  
Enter below the Model No. and Serial No. which  
are located on the top or bottom of the cabinet.  
Retain this information for future reference.  
0709DTSMDTJEIN  
Model No.  
GET0641-001A  
[J]  
EN  
Serial No.  
© 2009 Victor Company of Japan, Limited  
ESPAÑOL  
ENGLISH  
CANCELING THE DISPLAY DEMONSTRATIONS  
PREPARATIONS  
How to reset your unit  
Reset the unit after installation is complete.  
Attaching the control panel  
Detaching the control panel  
Turn on the power.  
Select “DEMO OFF.”  
Finish the procedure.  
(Initial setting)  
Your preset adjustments will also be erased.  
SETTING THE CLOCK  
How to forcibly eject a disc  
Turn on the power.  
Select “CLOCK M.”  
Be careful not to drop the disc when it ejects.  
If this does not work, reset your unit.  
Adjust the minute.  
(Initial setting)  
For safety...  
Warning  
Select “CLOCK H.”  
• Do not raise the volume level too much, as this will block  
outside sounds, making driving dangerous.  
• Stop the car before performing any complicated  
operations.  
If you need to operate the unit while driving, be sure to  
look around carefully or you may be involved in a traffic  
accident.  
Finish the procedure.  
Caution on volume setting  
Temperature inside the car...  
Adjust the hour.  
Discs produce very little noise compared with other sources.  
Lower the volume before playing a disc to avoid damaging  
the speakers by the sudden increase of the output level.  
If you have parked the car for a long time in hot or cold  
weather, wait until the temperature in the car becomes  
normal before operating the unit.  
IMPORTANT FOR LASER PRODUCTS  
1. CLASS 1 LASER PRODUCT  
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified  
service personnel.  
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.  
(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical  
instruments.  
INFORMATION (For U.S.A.)  
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of  
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential  
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used  
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no  
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference  
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to  
try to correct the interference by one or more of the following measures:  
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.  
– Reorient or relocate the receiving antenna.  
– Increase the separation between the equipment and receiver.  
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  
– Consult the dealer or an experienced radio/TV technician for help.  
Caution  
[European Union only]  
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.  
MORE ABOUT THIS UNIT  
– The files on the CD-R/CD-RW are written using the  
“Packet Write” method.  
– There are improper recording conditions (missing data,  
etc.) or media conditions (stained, scratched, warped,  
etc.).  
• The maximum number of characters for file/folder names  
vary depending on the disc format used (includes 4  
extension characters—<.mp3> or <.wma>).  
– ISO 9660 Level 1: up to 12 characters; ISO 9660 Level 2:  
up to 31 characters; Romeo: up to 64 characters; Joliet:  
up to 32 characters; Windows long file name: up to  
126 characters  
• This unit can recognize a total of 512 files, 255 folders,  
and 8 hierarchical levels.  
• This unit can play back files recorded in VBR (variable bit  
rate).  
Files recorded in VBR have a discrepancy in the elapsed  
time display, and do not show the actual elapsed time.  
In particular, this difference becomes noticeable after  
performing the search function.  
• This unit cannot play back the following files:  
– MP3 files encoded in: MP3i and MP3 PRO format, in an  
inappropriate format, layer 1/2.  
– WMA files: encoded in lossless, professional, and voice  
format; not based upon Windows Media® Audio; copy-  
protected with DRM.  
– Files which have data such as WAVE, ATRAC3, etc.  
• The search function works but search speed is not  
constant.  
Basic operations  
Disc operations  
• By pressing SRC on the unit, you can also turn on the  
power. If the source is ready, playback also starts.  
• If you turn off the power while listening to a disc, disc  
play will start from where it had been stopped previously  
next time you turn on the power.  
Caution for DualDisc playback  
• The Non-DVD side of a “DualDisc” does not comply with  
the “Compact Disc Digital Audio” standard. Therefore, the  
use of Non-DVD side of a DualDisc on this product may  
not be recommended.  
• CD-RWs may require a longer readout time since the  
reflectance of CD-RWs is lower than that of regular CDs.  
• When no disc is loaded in the unit, you cannot select  
“CD” as the playback source.  
General  
Playing an MP3/WMA disc  
• This unit has been designed to reproduce CDs/CD Texts,  
and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD  
(CD-DA) and MP3/WMA formats.  
• After ejecting a disc, “NO DISC” appears and you cannot  
operate some of the buttons. Insert another disc or press  
SRC to select another playback source.  
• This unit can play back MP3/WMA files with the  
extension code <.mp3> or <.wma> (regardless of the  
letter case—upper/lower).  
• This unit can show the names of albums, artists  
(performer), and tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for  
MP3 files and for WMA files.  
• This unit can display only one-byte characters. No other  
characters can be correctly displayed.  
• This unit can play back MP3/WMA files meeting the  
conditions below:  
– Bit rate: 8 kbps — 320 kbps  
– Sampling frequency:  
48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)  
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)  
– Disc format: ISO 9660 Level 1/ Level 2, Romeo, Joliet,  
Windows long file name  
Tuner operations  
• During SSM search...  
– All previously stored stations are erased and the  
stations are stored anew.  
– Received stations are preset in No. 1 (lowest  
frequency) to No. 6 (highest frequency).  
– When SSM is over, the station stored in No. 1 will be  
automatically tuned in.  
Playing a CD-R or CD-RW  
• Use only “finalized” CD-Rs or CD-RWs.  
• This unit can play back multi-session discs; however,  
unclosed sessions will be skipped while playing.  
• Some CD-Rs or CD-RWs may not be played back on this  
unit:  
– Discs are dirty or scratched.  
– Moisture condensation has occurred on the lens inside  
the unit.  
– The pickup lens inside the unit is dirty.  
1– EN  
General settings—PSM  
TROUBLESHOOTING  
Enter PSM menu.  
Select an item.  
Adjust.  
Finish  
Symptoms  
Remedies/Causes  
• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.  
• Check the cords and connections.  
Indication  
DEMO  
Item ( : Initial) Setting  
• The buttons on the unit do not work as you If you press M MODE, some buttons work differently from it  
intended.  
original function. Wait for 5 seconds or press M MODE again.  
DEMO ON  
:
Display demonstration will be activated automatically if no operation is done  
for about 20 seconds.  
Cancels.  
• This unit does not work at all.  
Reset the unit.  
DEMO OFF  
:
CLK DISP*1  
ON  
OFF  
:
:
Clock time is shown on the display at all times when the power is turned off.  
Cancels; pressing DISP will show the clock time for about 5 seconds when the  
power is turned off.  
• SSM automatic presetting does not work. Store stations manually.  
• Static noise while listening to the radio.  
• Disc ejects.  
Connect the antenna firmly.  
Insert the disc correctly.  
CLOCK H (Hour)  
1 12  
:
:
[Initial: 1 (1:00)]  
[Initial: 00 (1:00)]  
CLOCK M (Minute) 00 59  
• CD-R/CD-RW cannot be played back.  
• Tracks on the CD-R/CD-RW cannot be  
skipped.  
• Insert a finalized CD-R/CD-RW.  
• Finalize the CD-R/CD-RW with the component which you used  
for recording.  
DIMMER  
ON  
OFF  
:
:
Dims the display and button illumination.  
Cancels.  
SCROLL*2  
ONCE  
AUTO  
OFF  
:
:
:
Scrolls the displayed information once.  
Repeats scrolling (at 5-second intervals).  
Cancels.  
• Disc can be neither played back nor ejected. • Unlock the disc.  
• Eject the disc forcibly.  
• Disc sound is sometimes interrupted.  
• Stop playback while driving on rough roads.  
• Change the disc.  
• Pressing DISP for more than one second can scroll the display regardless of  
the setting.  
• Check the cords and connections.  
L/O MODE  
WOOFER*3  
AUX ADJ  
REAR  
:
Select if the REAR LINE OUT terminals are used for connecting the speakers  
(through an external amplifier).  
Select if the REAR LINE OUT terminals are used for connecting a subwoofer.  
• “NO DISC” appears on the display.  
• “PLEASE” and “EJECT” appear alternately  
on the display.  
Insert a playable disc into the loading slot.  
WOOFER  
:
LOW  
MID  
HIGH  
:
:
:
Frequencies lower than 90 Hz are sent to the subwoofer.  
Frequencies lower than 135 Hz are sent to the subwoofer.  
Frequencies lower than 180 Hz are sent to the subwoofer.  
• Disc cannot be played back.  
• Use a disc with MP3/WMA tracks recorded in a format compliant  
with ISO 9660 Level 1, Level 2, Romeo, or Joliet.  
• Add the extension code <.mp3> or <.wma> to the file names.  
A.ADJ 00  
A.ADJ 05  
:
Adjust the auxiliary input level to avoid the sudden increase of the output  
level when changing the source from external component connected to the  
AUX input jack on the control panel.  
• Noise is generated.  
Skip to another track or change the disc. (Do not add the extension  
code <.mp3> or <.wma> to non-MP3 or WMA tracks.)  
TAG DISP  
TAG ON  
TAG OFF  
:
:
Shows the Tag while playing MP3/WMA tracks.  
Cancels.  
• A longer readout time is required  
(“READING” keeps flashing on the display).  
Do not use too many hierarchical levels and folders.  
AMP GAIN*4  
LOW PWR  
:
VOL 00 – VOL 30 (Select if the maximum power of each speaker is less than  
50 W to prevent damaging the speaker.)  
VOL 00 – VOL 50  
• Tracks are not played back in the order you Playback order is determined when the files are recorded.  
have intended.  
HIGH PWR  
:
:
AREA  
AREA US  
When using in North/Central/South America. AM/FM intervals are set to  
10 kHz/200 kHz.  
When using in any other areas. AM/FM intervals are set to 9 kHz/50 kHz  
(100 kHz during auto search).  
When using in South American countries where FM interval is 100 kHz.  
AM interval is set to 10 kHz.  
• The elapsed playing time is not correct.  
This sometimes occurs during playback. This is caused by how the  
tracks are recorded on the disc.  
AREA EU  
:
:
• The correct characters are not displayed  
(e.g. album name).  
This unit can only display alphabets (upper case), numbers, and a  
limited number of symbols.  
AREA SA  
1
*
If the power supply is not interrupted by turning off the ignition key of your car, it is recommended that you select “OFF” to  
save the car’s battery.  
Some characters or symbols will not be shown correctly (or will be blanked) on the display.  
Displayed only when “L/O MODE” is set to “WOOFER.”  
The volume level automatically changes to “VOL 30” if you change to “LOW PWR” while the volume level is set higher than  
“VOL 30.”  
• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United  
States and/or other countries.  
2
3
4
*
*
*
MAINTENANCE  
How to clean the connectors  
Wipe the connectors with  
a cotton swab or cloth  
To keep discs clean  
Do not use the following discs:  
Single CD—8 cm (3-3/16”) disc  
Wipe in a straight line from center of disc to  
edge. Do not use liquid cleaners, thinners, or  
benzene.  
Warped disc  
Sticker and sticker residue  
Stick-on label  
moistened with alcohol.  
Connectors  
Moisture condensation  
To play new discs  
Remove any rough areas from the inner and  
outer edges of the disc.  
Transparent or semi-transparent  
parts on its recording area  
Moisture may condense on the lens inside the unit. Eject  
the disc and leave the unit turned on for a few hours until  
the moisture has evaporated.  
Unusual shape  
C-thru Disc (semi-transparent disc)  
SPECIFICATIONS  
Audio amplifier section  
Power Output:  
20 W RMS × 4 Channels at 4 Ω and  
≤ 1% THD+N  
Signal-to-Noise Ratio:  
80 dBA (reference: 1 W into 4 Ω)  
Tuner section  
Frequency Range:  
FM: 87.5 MHz to 107.9 MHz  
(with channel interval set to 100 kHz or 200 kHz)  
87.5 MHz to 108.0 MHz  
CD player section  
General  
Type:  
Compact disc player  
Power Requirement:  
Operating Voltage: DC 14.4 V  
(11 V to 16 V allowance)  
Negative ground  
Signal Detection System: Non-contact optical pickup  
(semiconductor laser)  
Grounding System:  
Number of channels:  
Frequency Response:  
Dynamic Range:  
2 channels (stereo)  
5 Hz to 20 000 Hz  
93 dB  
Allowable Operating Temperature:  
0°C to +40°C (32°F to 104°F)  
Dimensions (W × H × D):  
Installation Size (approx.):  
182 mm × 52 mm × 160 mm  
(7-3/16” × 2-1/16” × 6-5/16”)  
Panel Size (approx.):  
(with channel interval set to 50 kHz)  
AM: 530 kHz to 1 710 kHz  
(with channel interval set to 10 kHz)  
531 kHz to 1 602 kHz  
(with channel interval set to 9 kHz)  
Signal-to-Noise Ratio:  
Wow and Flutter:  
MP3 Decoding Format:  
98 dB  
Load Impedance:  
Tone Control Range:  
4 Ω (4 Ω to 8 Ω allowance)  
Bass: 12 dB at 60 Hz  
Mid-range: 12 dB at 1 kHz  
Treble: 12 dB at 7.5 kHz  
40 Hz to 20 000 Hz  
Less than measurable limit  
MPEG1/2 Audio Layer 3  
Max. Bit Rate: 320 kbps  
[FM Tuner]  
WMA (Windows Media® Audio) Decoding Format :  
Max. Bit Rate: 192 kbps  
188 mm × 58 mm × 5 mm  
(7-7/16” × 2-5/16” × 1/4”)  
Mass (approx.):  
Frequency Response:  
Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω)  
50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω)  
Alternate Channel Selectivity (400 kHz): 65 dB  
Frequency Response: 40 Hz to 15 000 Hz  
Stereo Separation: 35 dB  
Line-Out Level/Impedance: 2.5 V/20 kΩ load (full scale)  
Output Impedance: 1 kΩ  
Subwoofer-Out Level/Impedance:  
2.5 V/20 kΩ load (full scale)  
1.3 kg (2.9 lbs) (excluding accessories)  
Having TROUBLE with operation?  
Design and specifications are subject to change without  
notice.  
Please reset your unit  
Still having trouble??  
[AM Tuner]  
Sensitivity/Selectivity: 20 μV/35 dB  
If a kit is necessary for your car, consult your telephone  
directory for the nearest car audio speciality shop.  
Call 1-800-252-5722 (USA ONLY)  
3 – EN  
PREPARATION  
TROUBLESHOOTING  
You need the installation kits which corresponds to your car.  
• The fuse blows. ] Are the red and black leads connected correctly?  
• Power cannot be turned on. ] Is the yellow lead connected?  
• No sound from the speakers. ] Is the speaker output lead short-circuited?  
• Sound is distorted. ] Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers grounded in  
common?  
• Mark all the check boxes ( ) to make sure you have follow the instructions and the listed parts.  
Check the battery system in your car  
Prepare this before installation  
• Noise interfere with sounds. ] Is the rear ground terminal connected to the car’s chassis using shorter and thicker  
12 V DC, NEGATIVE ground  
cords?  
• This unit becomes hot. ] Is the speaker output lead grounded? ; Are the “–” terminals of L and R speakers  
grounded in common?  
• This unit does not work at all. ] Have you reset your unit?  
Parts list for installation and connection  
A Control panel  
B Sleeve  
C Trim plate  
D Power cord  
E Handles  
F Remote controller  
G Battery  
INSTALLATION  
The following illustration shows a typical installation. If you are not sure how to install this unit correctly, contact your JVC car audio dealer or a company supplying kits.  
In-dash mounting  
When installing the unit without using the sleeve  
In a Toyota car for example, first remove the car radio and install the unit in  
its place.  
See “ELECTRICAL  
CONNCECTIONS” below.  
8 mm (3/8")  
Flat head screwsM5 × 8 mm (3/8")*2  
Pocket  
Bracket*2  
Removing the unit  
Release the rear section first...  
ELECTRICAL CONNECTIONS  
Make sure to disconnect the battery’s negative terminal.  
Be sure to ground this unit to the car’s chassis again after installation.  
High  
Note:  
It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the  
maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see “General settings—PSM”).  
Heat sink  
Typical connections  
Connecting the external amplifier or subwoofer  
Remote lead  
Y-connector *2  
Rear line out  
Rear ground terminal  
Remote lead (blue with white stripe)  
Antenna  
terminal  
Set “L/O MODE” to “REAR”  
(See “General settings—PSM.”)  
You can connect a power amplifier for rear  
speakers.  
15 A fuse  
To the remote lead of other equipment  
or automatic antenna if any  
Ignition switch  
Signal cord*2  
Black  
To the metallic body  
or chassis of the car  
Connect only the front speakers if your  
speaker system is two-speaker system.  
Rear  
JVC Amplifier  
speakers  
To a live terminal in the  
fuse block connecting to the  
car battery (bypassing the  
ignition switch) (constant  
12 V)  
Right  
Left  
White with black stripe  
Yellow *3  
Front speakers  
Set “L/O MODE” to “WOOFER”  
(See “General settings—PSM.”)  
You can also connect a subwoofer to the REAR  
LINE OUT terminals.  
Front speaker (left)  
White  
Fuse block  
Gray with black stripe  
Red  
To an accessory terminal in  
the fuse block  
or  
JVC Amplifier  
Front speaker (right) Gray  
Green with black stripe  
Subwoofer  
Blue with white  
stripe  
To the remote lead of other  
equipment or automatic antenna if  
any (200 mA max.)  
PRECAUTIONS on power supply and speaker connections  
Rear speaker (left)  
Green  
Purple with black stripe  
IMPORTANT  
Rear speaker (right)  
Purple  
1
*
*
*
When you stand the unit, be careful not to damage the fuse on the rear.  
Not supplied for this unit.  
Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the power cannot be  
turned on.  
Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with paint (if coated  
with paint, remove the paint before attaching the wire). Failure to do so may cause damage to the unit.  
2
3
RECOMMENDED CONNECTION  
Custom wiring harness*2  
4
*
4 – EN  

Maxtor OneTouch STM310005OTA3E1 RK User Manual
LG Electronics P505R User Manual
Lenoxx Electronics CD 103 User Manual
KitchenAid KSSS48M User Manual
KitchenAid KECN507Y User Manual
Insignia NS P3114 User Manual
ID Tech 60 User Manual
HTC EVO 4G PC36100 User Manual
Cisco Systems Cisco Collab Experience Dx650 CPDX650K9 User Manual
Audiovox SP 6CD User Manual