DataPort™ 250
USB 2.0 Enclosure
User’s Guide
WWW.CRU-DATAPORT.COM • (800) 260-9800
PACKAGE CONTENTS
·
·
·
·
·
·
DataPort 250
Power Supply
Power Cable for PS/2 Port
USB cable
Carrying Case
User’s Manual
If you are missing any of the above items please contact
the place of purchase to get replacements. For further
assistance, contact CRU-DataPort at 800-260-9800.
1
WWW.CRU-DATAPORT.COM • (800) 260-9800
WWW.CRU-DATAPORT.COM • (800) 260-9800
DataPort™ 250
FEATURES AND REQUIREMENTS
·
·
USB 2.0 supports transfer rates up to 480 Mb/sec
Enables the addition of a 2.5 IDE hard drive up to
9.5mm thickness
·
·
·
USB 2.0 is backwards compatible with USB 1.1
Plug-n-Play, hot swappable
Three ways are provided to power the DP250 and hard
drive: bus power, PS/2 port (power cable included) and
external power supply (AC power adapter included)
Power/hard drive activity LED (green indicator shows
steady illumination to show power on, flickers to indi-
cate hard drive activity)
·
·
·
Space saving design
1 year warranty
For PC Users
â
·
·
Windows 98SE, 2K, ME & XP
USB 2.0 Port
For Mac Users
·
·
Mac OS 9.7 & X
USB Port (Currently Apple only provides USB 1.1)
â
3
2
WWW.CRU-DATAPORT.COM • (800) 260-9800
WWW.CRU-DATAPORT.COM • (800) 260-9800
INSTALLING THE HARD DISK DRIVE (DP250)
USB input
1. Leverage the side of the enclosure open with a small screwdriver.
2. Slide the hard drive onto the connector.
3. Close the enclosure by connecting one side then clipping in the other.
4. Connect the provided USB cable between your computer’s USB port and
the DP250 enclosure.
Power
Input
Diagram 1 Rear panel 250 USB enclosure
5. There are three ways to power your DP250 enclosure and hard drive:
USB bus powered, PS/2 port, and external power supply (AC power
adapter):
·
Bus powered: If your computer’s USB port features standard USB
port power (DC 5V / 0.5A), your USB port will supply adequate
power for most applications. However, certain models of hard drives
may require additional power. Also, if the bus power is shared by more
than one USB device, there may not be sufficient power for the DP250
and hard drive. Where USB bus power is not sufficient, the PS/2 port
or external power supply should be used.
·
PS/2 port: The PS/2 port on your computer can be used to supply
power to your DP250. Plug the provided PS/2 power cable into an
available PS/2 port on your computer. Plug the power input end of the
PS/2 cable into the power input on the back of the DP250 enclosure.
(The PS/2 cable also provides a connector for your keyboard. If
desired, your keyboard can be unplugged from your computer to free
up a PS/2 port. Your keyboard can then be plugged into the PS/2
connector on the power cable). The PS/2 power cord will power the
DP250 enclosure and drive provided your computer’s PS/2 port
supplies sufficient power.
·
An external power supply is also provided in case your computer
does not supply adequate power through the USB bus or PS/2 port.
To use the external power supply, plug the power cord into the back of
the enclosure (which requires DC 5V / 2.0A provided by the power
supply) and into an external power source. Power source is a standard
AC 100-240V 47-63 Hz outlet.
Diagram 2
4
5
WWW.CRU-DATAPORT.COM • (800) 260-9800
WWW.CRU-DATAPORT.COM • (800) 260-9800
Setting up the Drive for Windows 98 & Windows ME
WARNING: Formatting your drive will result in loss of data.
To install a drive on your computer for Windows 98 via the USB port
you must download the drivers from CRU’s website (www.CRU-
DataPort.com). On the left side of the page you will see a link titled
Support. Click on Support, then USB Drivers, and select the Win-
dows 98SE USB drivers link. Download the Win98 file and follow the
instructions on the website to install it. (Windows ME does not require
a special driver).
Plug the USB DataPort™ 250 into your computer.
The Device Driver Wizard will pop up. Click on next. The “recom-
mended” option will be selected: hit next. The wizard will be set to
install the software automatically. Hit next and the wizard will ask
where to look for the driver. Select the directory that you opened the
driver into or select the primary drive and let the computer find it.
Once the driver installation is completed hit close.
·
·
·
·
·
Right Click on My Computer and select Properties.
Select the Device Manager tab.
Click on the + beside Disk Drives.
Right click on your drive and select Properties.
Select the Settings tab and place a check beside Removable.
After completing these steps, you will have to reboot your computer.
Once your computer has booted up you should see an additional icon
on your Task Bar. Double click My Computer. Your new drive
should now be listed. Double click on the drive. If it is a new drive or
a drive with an incompatible format, it will ask you to format it. Click
Yes. A new window will appear. At the top the capacity of your drive
will be listed, directly below that will be a section titled Format Type.
In this section you will select Full and select Start. Read and follow
the instructions to finish setting up your drive. REMEMBER, format-
ting your drive will result in loss of data.
Diagram 3
6
7
WWW.CRU-DATAPORT.COM • (800) 260-9800
WWW.CRU-DATAPORT.COM • (800) 260-9800
Setting up the Drive for Windows 2000
WARNING: Formatting your drive will result in loss of data.
Connect the DataPort™250 to your computer. A new window will pop
up for the New Hardware Wizard (see Diagram 4). Follow the
instructions to add the new drive. After completing these instructions,
do the following:
·
·
·
Right click on My Computer
Click on Manage
In the Storage sub-section, click on Disk Management to
display a list of all the drives connected to your computer.
If you have not used the drive before you will have to partition it.
Left click on Action, select All Tasks and then left click on
Create Partition. REMEMBER, formatting will result in loss
of data.
·
Diagram 5
Setting Up the Drive for Windows XP
·
This will bring up the Create Partition Wizard screen (see
Diagram 5). Follow the instructions and the drive will be ready
to use.
WARNING: Formatting your drive will result in loss of data.
Connect the DataPort™ 250 to your computer. Check to see if the
hard disk drive is accessible in My Computer. If it does not show up,
do the following:
·
·
·
Right click on My Computer
Click on Manage
In the Storage sub-section click on Disk Management; this
will show all the drives connected to your computer.
If you are prompted to initialize the drive, follow the directions.
REMEMBER, formatting your drive will result in loss of data.
·
You should now see the hard disk drive in the list of drives on the right
side of your window.
Right click on the drive and click New Partition (see Diagram 5).
This will launch a wizard that allows you to partition the drive, format it,
and assign it a drive letter.
Diagram 4
8
9
WWW.CRU-DATAPORT.COM • (800) 260-9800
WWW.CRU-DATAPORT.COM • (800) 260-9800
Setting Up the Drive for Macs
WARNING: Formatting your drive will result in loss of data.
After connecting the DataPort™ 250 to your Mac, a new disk should
be added to your desktop. If the drive is not correctly formatted you
will be asked to initialize it (see Diagram 6). Click on the partition
tab and set your desired partitions, then click ok (see Diagram 7).
The new disk will be added to your desktop. REMEMBER, format-
ting your drive will result in loss of data.
Diagram 7
Diagram 6
10
11
WWW.CRU-DATAPORT.COM • (800) 260-9800
WWW.CRU-DATAPORT.COM • (800) 260-9800
Removing the Hard Disk Drive
TROUBLE SHOOTING
Win 98SE, ME, 2K and XP
·
·
·
Right click on the green arrow icon on the system tray
Select Remove/Reject
Highlight the USB Mass Storage Device in the dialog box
then click on Stop.
For the DataPort™ 250 to be properly recognized, it is important your
computer has the latest available driver updates provided by the
manufacturer of your software and hardware.
·
·
·
Choose the external disk drive that you want to disconnect,
then click on Stop.
Wait until the “You may safely remove this device” message
appears.
If your USB port was added to your computer via a PCI card, make
sure that the software provided by the manufacturer was properly
installed and is the latest version. If your USB port came with your
â
computer, make sure that you have available updates from Microsoft
Unplug the cable from the computer.
â
or Apple . (Further information can be found at the CRU-DataPort
WARNING: If your computer reports that the drive is busy, you
must shut down your computer and then remove the drive. Failure
to do so may result in data loss or corruption.
Check all cable connections.
Mac OS 9.7/X
Contact CRU-DataPort Technical support for further assistance.
·
When you disconnect the external drive from the Mac, close all
windows and quit all applications that are running on the exter-
nal drive.
·
Drag the external drive icon into Trash to dismount it from the
desktop prior to unplugging the drive.
12
13
WWW.CRU-DATAPORT.COM • (800) 260-9800
WWW.CRU-DATAPORT.COM • (800) 260-9800
Limited Product Warranty:
TECHNICAL SUPPORT
CRU-DataPort warrants the DataPort™ 250 to be free of significant
defects in material and workmanship for a period of one (1) year from
the original date of purchase. CRU-DataPort’s warranty is nontrans-
ferable and is limited to the original purchaser.
Contact your dealer for technical support first. If you still need
assistance, then contact the CRU-DataPort technical support depart-
ment. You can contact CRU-DataPort’s technical support department
sending an E-mail message to [email protected]. Techni-
cal support is also available by phone at:
Please note: CRU-DataPort’s limited product warranty is not intended
to allow customers to upgrade their CRU-DataPort products to newer
versions.
(800) 260-9800 during the hours of: 8:00 AM to 5:00 PM, PST
Monday through Friday, or by FAX (360)896-1017.
Product Remedies:
CRU-DataPort’s entire liability and the original purchaser’s exclusive
remedy for any breach of warranty, shall be, at CRU-DataPort’s
option, either (a) return of the price paid or (b) repair or replacement
of the hardware, provided that the hardware is returned to CRU-
DataPort, with a copy of the sales receipt or applicable documenta-
tion. Any replacement hardware will be warranted for the remainder of
the original warranty period.
When you call, please have the following information ready:
·
·
The part number of your CRU DataPort(s)
The manufacturer’s name and model number of the hard disk
drive and computer system you are using
·
·
Any error messages that appeared on your screen
The name of the dealer from which you purchased your CRU-
DataPort product(s)
These remedies are void if failure of the hardware has resulted from
accident, abuse, misapplication or modification. (This will be deter-
mined by CRU-DataPort.)
14
15
WWW.CRU-DATAPORT.COM • (800) 260-9800
WWW.CRU-DATAPORT.COM • (800) 260-9800
Material Return:
Any product being returned to CRU-DataPort, either by a distributor, dealer
or an end user, for repair or replacement must be accompanied by a
Return Material Authorization (RMA) number, which must be obtained by
contacting CRU-DataPort’s Customer Service Department at 800-260-
9800.
Limitation of Liability:
The warranties set forth in this agreement replace all other warranties.
CRU-DataPort expressly disclaims all other warranties, including but
not limited to, the implied warranties of merchantability and fitness for
a particular purpose and noninfringement of third-party rights with
respect to the documentation and hardware. No CRU-DataPort
dealer, agent or employee is authorized to make any modification,
extension, or addition to this warranty. In no event will CRU-DataPort
or its suppliers be liable for any costs of procurement of substitute
products or services, lost profits, loss of information or data, computer
malfunction, or any other special, indirect, consequential, or incidental
damages arising in any way out of the sale of, use of, or inability to
use any CRU-DataPort product or service, even if CRU-DataPort has
been advised of the possibility of such damages. In no case shall
CRU-DataPort’s liability exceed the actual money paid for the prod-
ucts at issue.
Please have these items available when requesting an RMA:
CRU-DataPort Part Number(s), and your return “Ship To” Address.
IMPORTANT: Returned material must be properly packed to
avoid in-transit damage. Damage to CRU products due to
improper packaging will not be covered by this warranty.
Product return packages must be labeled on the outside of the box
as follows:
CRU-DataPort.
RMA Dept./RMA #XXXX
1000 SE Tech Center Drive, Suite 160
Vancouver, WA 98683
CRU-DataPort reserves the right to make modifications and additions
to this product without notice or taking on additional liability.
CRU-DataPort will apply its warranty policy and issue RMA numbers
based on a review of the specific circumstances of each request. CRU-
DataPort will, at its sole discretion, determine if a product is valid for return
to CRU-DataPort or if another remedy is applicable.
Actual credit or refund for any item returned to CRU-DataPort will only be
applied once the item has been received by CRU-DataPort and approved
to adhere to CRU-DataPort’s Warranty and RMA policies.
RMA product(s) sent to CRU-DataPort must be received within 30 days of
the original RMA issue date. All products on each RMA must be shipped
together. Prior to returning defective product(s), contact a CRU-DataPort
Technical Support Specialist for problem analysis and replacement ap-
proval at 800-260-9800. To return defective product(s), please follow the
guidelines below, in addition to the general RMA guidelines described
above in the “Material Return” section.
16
17
WWW.CRU-DATAPORT.COM • (800) 260-9800
WWW.CRU-DATAPORT.COM • (800) 260-9800
Advance Replacement:
Advance Replacement requests require an Advance Replacement Authori-
zation, pre-approved by a CRU-DataPort Technical Support Specialist.
Advance Replacements also require a credit card to secure the product
being replaced. Advance replacements will typically ship within one day of
RMA issue date and authorization. CRU-DataPort will pay outbound freight
and insurance only.
Defective Product Return Beyond 30 Days:
CRU-DataPort products under warranty, but beyond 30 days of the original
purchase date, are subject to repair only. To return product(s) after 30
days, please follow the guidelines below, in addition to the general RMA
guidelines described above in the “Material Return” section.
Prior to returning defective product(s), contact a CRU-DataPort Technical
Support Specialist for problem analysis and replacement approval at 800-
260-9800.
Defective product(s) must be sent freight pre-paid and insured by the
requestor.
Repair replacement product(s) will be return shipped from CRU-DataPort,
freight pre-paid and insured by CRU-DataPort, within three to seven
business days of receipt (depending on quantity & repair type). Please
allow sufficient shipping time to and from locations; allow three business
days for repair. CRU-DataPort ships all repairs via standard UPS ground
unless otherwise agreed to when the RMA is issued.
Rev. 1
18
WWW.CRU-DATAPORT.COM • (800) 260-9800
|