IBM W2H User Manual

SurePOS 300  
ꢀꢁꢂ  
Installation and Service Guide for  
4810/4910  
Model 31x, 32x, W2H  
11-9-2005  
GA27-4309-01  
SurePOS 300  
ꢀꢁꢂ  
Installation and Service Guide for  
4810/4910  
Model 31x, 32x, W2H  
11-9-2005  
GA27-4309-01  
11-9-2005  
Note  
Before using this information and the products it supports, be sure to read the safety information booklet (GA27-4004) and  
the general information under Appendix B, “Notices,” on page B-1.  
Second Edition (March 2005)  
|
|
|
This edition applies to IBM Point-of-Sale terminals, 4810 and 4910 (includes the 4810 terminal bundled with a printer,  
display, cash drawer, and possibly other I/O). This publication is available on the IBM Retail Stores Solutions  
Electronic Support Web site.  
2. Select Support  
3. Select Publications  
You can order publications through your IBM representative or the IBM branch office that serves your locality.  
Publications are not stocked at the address given below.  
IBM welcomes your comments. A form for readers’ comments is provided at the back of this publication. If the form  
has been removed, you can send your comments to the following address:  
Department CNPA  
Design & Information Development  
IBM Corporation  
PO Box 12195  
Research Triangle Park, NC 27709  
U.S.A.  
When you send information to IBM, you grant IBM a nonexclusive right to use or distribute whatever information you  
supply in any way it believes appropriate without incurring any obligation to you.  
© Copyright International Business Machines Corporation 2002, 2004. All rights reserved.  
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract  
with IBM Corp.  
 
11-9-2005  
Contents  
|
|
|
© Copyright IBM Corp. 2002, 2004  
iii  
11-9-2005  
iv SurePOS Installation and Service  
11-9-2005  
vi SurePOS Installation and Service  
11-9-2005  
About this guide  
This guide provides product planning information, replacement and removal  
procedures, problem determination and parts listings of field-replaceable-units  
(FRUs) for the IBM 4810/4910 SurePOS300. The 4910-32x model is an Express  
solution, which includes a 4810-32H machine, a printer, display, cash drawer, and  
possibly other I/O. The components of the 4910 Express Solution are determined  
by each country or geographical region.  
|
|
|
|
Throughout this guide, the term 4810 refers to all models of the IBM 4810/4910  
SurePOS 300. The chapters are organized as follows:  
v Chapter 1, “Introduction,” on page 1-1 provides a summary of all the models of  
the IBM 4810/4910 SurePOS 300.  
the procedure for removing parts from the 4810/4910.  
resolving problems.  
v Chapter 4, “Parts catalog,” on page 4-1 provides the most recent parts  
|
information for the product.  
Who should read this manual  
This manual is intended for use by experienced personnel responsible for installing  
and maintaining all models of the IBM 4810 SurePOS 300.  
Related publications  
The following IBM publications, drivers, and service diskette information are  
available from the IBM Retail Store Solutions Web site at:  
v IBM 4820 SurePoint Solution: System Reference, SA27-4249  
v IBM 4820 SurePoint Solution Installation and Service Guide, GA27-4231  
v IBM 4810 SurePOS 300 Technical Reference  
|
v IBM SurePOS 500/600 Series Planning, Installation, and Operation Guide,  
GA27-4254  
v IBM SurePOS 500/600 Series Hardware Service Guide, GY27-0396  
v SureMark Printers User’s Guide, GA27-4151  
v SureMark Printers Hardware Service Manual, GY27-0355  
|
|
Driver and Service Diskette Information  
v Terminal hardware folder  
– 4820 downloads  
-
4694/4695/ISA Service Diskette, Version 5.33 or later  
v Peripheral Drivers folder  
– IBM POSS Suite, which includes:  
- POS Device Diagnostics  
- POSS for Windows  
- OLE for POS (OPOS)  
- JavaPOS  
© Copyright IBM Corp. 2002, 2004  
vii  
 
11-9-2005  
– 4820 Touch Drivers for SurePOS 700 Series, which includes the MicroTouch™  
TouchWare™  
– POSS for DOS download  
Accessibility  
|
|
|
Accessibility features help a user who has a physical disability, such as restricted  
mobility or limited vision, to use the 4810/4910 SurePOS 300 successfully. The  
following is a high-level list of the accessibility features:  
v All controls are located on the front of the machine, in easy reach.  
v Industry-standard serial and USB ports allow alternative I/O devices.  
v Manuals are available in .PDF format and can be downloaded from the Web.  
v Displays can be driven at 60 Hz to eliminate problems caused by screen flicker.  
| Uninterruptible power supply option  
|
|
This product contains a sealed lead acid battery. The battery must be recycled or  
disposed of properly.  
|
|
|
|
In the United States, IBM has established a collection process for reuse, recycling,  
or proper disposal of used IBM sealed acid batteries. For information about proper  
disposal of these batteries, please contact IBM at 1–800–426–4333. Please have  
the IBM part number listed on the battery available prior to your call.  
|
|
For information disposal of sealed acid batteries outside the United States, go to  
the following URL or contact your local waste disposal facility.  
|
End of life disposal  
This unit must be recycled or discarded according to applicable local and national  
regulations. IBM encourages owners of information technology (IT) equipment to  
responsibly recycle their equipment when it is no longer needed. IBM offers a  
variety of product return programs and services in several countries to assist  
equipment owners in recycling their IT products. Information on IBM product  
recycling offerings can be found on IBM’s Internet site at  
Notice: This mark applies only to countries within the European Union (EU) and  
Norway.  
Appliances are labeled in accordance with European Directive 2002/96/EC  
concerning waste electrical and electronic equipment (WEEE). The Directive  
determines the framework for the return and recycling of used appliances as  
applicable throughout the European Union. This label is applied to various products  
to indicate that the product is not to be thrown away, but rather reclaimed upon end  
of life per this Directive.  
viii SurePOS Installation and Service  
 
11-9-2005  
In accordance with the European WEEE Directive, electrical and electronic  
equipment (EEE) is to be collected separately and to be reused, recycled, or  
recovered at end of life. Users of EEE with the WEEE marking per Annex IV of the  
WEEE Directive, as shown above, must not dispose of end of life EEE as unsorted  
municipal waste, but use the collection framework available to customers for the  
return, recycling, and recovery of WEEE. Customer participation is important to  
minimize any potential effects of EEE on the environment and human health due to  
the potential presence of hazardous substances in EEE. For proper collection and  
treatment, contact your local IBM representative.  
Disposal of IT products should be in accordance with local ordinances and  
regulations.  
About this guide ix  
11-9-2005  
Tell us what you think  
Your feedback is important in helping us provide accurate and high-quality  
information. Please take a few moments to tell us what you think about this  
document.  
You can use either of these ways to provide feedback:  
then Publications. Select the publication comments link within the introductory  
text. Fill in the requested information and your comments. Be sure to include the  
name and form number of the document in the Publication ID field.  
v Print and fill out the form at the end of this document. Return the form to us by  
mail or by giving it to an IBM representative.  
If applicable, include a reference to the specific location of the text (for example, the  
page or table number) on which you are commenting.  
Between major revisions of this document, we might make minor technical updates.  
The latest version of this document is available on the Retail Store Solutions Web  
x
SurePOS Installation and Service  
 
11-9-2005  
Summary of changes  
|
|
|
|
November 2005  
v Inserted the new End-of-Life disposal statement  
v Inserted the new Tell us what you think statements  
v Added supported models to front cover  
|
|
|
|
|
|
February 2005  
Updated information on IBM SurePOS 300 to include the 4910-32x model,  
which is an Express solution that includes the 4810-32H, a printer, display,  
cash drawer, and possibly other I/O devices. The 4910 Express solutions  
are country and geographically specific. A revision bar (|) in the left margin  
indicates updated sections.  
December 2004  
Added I/O commands information in a new appendix.  
June 2004  
Added information about new Model W2H. Changed or new information is  
indicated by a revision bar (|) in the left margin.  
April 2004  
Deleted reference to the IBM Compact ANPOS Keyboard, GA27-4187-00  
and added references to IBM SurePOS 500/600 Series Planning,  
Installation, and Operation Guide and IBM SurePOS 500/600 Series  
Hardware Service Guide, GY27-0396. Added information about the 1.2 GHz  
CPU to the parts catalog.  
November 2003  
Corrected minor technical errors.  
May 2003  
Added information about new Model 32x. Updated the parts catalog.  
© Copyright IBM Corp. 2002, 2004  
xi  
 
11-9-2005  
xii SurePOS Installation and Service  
11-9-2005  
Chapter 1. Introduction  
This chapter describes the characteristics of the IBM 4810 SurePOS 300, which  
includes the machine type 4910.  
Product summary  
|
|
|
|
|
|
The 4810 consists of a personal computer (PC) core with expansion slots,  
Electronic Industries Association (EIA) 232 connectors, an Ethernet LAN adapter,  
and built-in video (VGA) support. In addition to these features, the 4910 SurePOS  
Express Model includes bundled I/O that may vary according to country and  
geographic region. Designed specifically for distributed environments, the 4810 can  
be mounted vertically or horizontally under a check stand or counter.  
Features  
|
Table 1-1 describes the features of the 4810/4910 SurePOS 300.  
Table 1-1. Summary of features  
Feature  
CPU  
Model 31x  
Model 32x / Model W2H  
VIA C3 866 MHz /133 MHz  
VIA C3 1.2 GHz / 133 MHz  
I/O ports  
v One parallel printer port  
v Four RS-232 ports:  
– Two standard  
v Six RS-232 ports:  
– Four standard  
– Two powered  
– Two powered  
v Four standard, USB ports  
v Keyboard and mouse ports  
v One cash drawer port  
v Four standard, USB ports  
v Keyboard and mouse ports  
Memory  
v Two DIMM slots for industry-standard PC133 SDRAM  
v 128 MB standard, expandable to 512 MB  
Video  
LAN  
SVGA interface  
10/100 Ethernet chip capable of supporting both 10BASE-T or 100BASE-TX  
full- or half-duplex Ethernet. Wired for Management (WfM 2.0).  
Slots  
One PCI feature card slot (half size)  
Nonvolatile real time clock  
Clock  
Keyboard/  
mouse  
IBM PS/2® or equivalent keyboard  
Flash  
memory  
Optional Type II Compact Flash socket (mutually exclusive with the 40-GB  
hard disk drive). This socket is internal to the unit and is not for devices that  
are removed or inserted as part of their function.  
Hard disk  
Optional 3.5-inch IDE (mutually exclusive with the flash memory).  
drive (HDD)  
Audio  
AC97-compatible audio with microphone in, line in and line out.  
The following table lists the standard features shipped with each model:  
|
|
|
|
|
Table 1-2. Models and features  
Model  
Base-unit standard feature  
Base model, no media  
40-GB HDD  
4810-310/320  
4810-31H/32H  
4810-31C/32C  
128-MB flash memory  
© Copyright IBM Corp. 2002, 2004  
1-1  
 
Product introduction  
11-9-2005  
|
|
|
Table 1-2. Models and features (continued)  
Model  
4810-W2H  
Base-unit standard feature  
40-GB HDD, Microsoft® Windows® XP Professional preloaded  
|
|
4910-32H/32E/32A 40-GB HDD  
|
|
Note: References in this guide to the 4810 Model 32x also apply to the 4810  
Model W2H and 4910 Models 32H, 32E and 32A.  
Physical dimensions  
Figure 1-1 shows the dimensions of the product:  
|
90 mm  
(3.5 in.)  
300 mm  
(11.8 in.)  
216 mm  
(8.5 in.)  
|
|
|
Figure 1-1. Dimensions of the 4810/4910 SurePOS 300 (does not include the I/O devices for the Express models)  
v Width: 300 mm ( 11.8 in.)  
v Depth: 216 mm ( 8.5 in.)  
v Height: 90 mm ( 3.5 in.)  
v Weight: 3.2 kg ( 7 lb.)  
Power and cooling  
Attention  
When installing a new power supply, be sure to set the correct input voltage  
for your area or you will damage the power supply. See Figure 1-3 on page  
1-4 to locate the voltage selection switch.  
v Input voltage: 100 - 127 V or 200 - 240 V ac (select using switch)  
v Frequency: 50 - 60 Hz ( 3 Hz)  
v Power consumption: 100 W maximum; 35 W typical  
A fan contained in the power supply provides forced air cooling.  
1-2 SurePOS Installation and Service  
 
Product introduction  
11-9-2005  
Environmental considerations  
Temperature and humidity requirements are as follows:  
v Operating: +10°C to 40°C (50° to 104°F) with 8% to 80% relative humidity  
v Shipping: −40°C to +60°C (−40° to 140° F), which includes condensation but not  
rain.  
v Storage: 0°C to +60°C (32° to 140° F)  
|
|
|
The 4810/4910 SurePOS 300 meets all worldwide Electromagnetic Compatibility  
(EMC) standards. Refer to Appendix B, “Notices,” on page B-1 for a complete  
description.  
Front view and LEDs  
|
Figure 1-2 shows the LEDs of the 4810/4910.  
OK  
OK  
Figure 1-2. Front view of 4810/4910  
The LEDs function as follows:  
|
This LED indicates that the 4810/4910 is powered on.  
This LED, which blinks during HDD access, indicates HDD activity.  
OK  
Chapter 1. Introduction 1-3  
 
Product introduction  
11-9-2005  
This network connection LED is on when the 4810/4910 is connected to a  
|
|
hub or switch.  
This LED blinks during receive/send transmission.  
Rear connectors  
|
|
|
See the rear connector for your 4810/4910 model:  
| Rear connectors 4810 (31x models)  
|
|
Figure 1-3 shows the connections available on the 4810 (models 31x) and  
4910-32H:  
Note: Not sure whether placing 4910 in the heading is correct. Please advise  
whether the 4910 models would follow the current grouping of the rear  
connectors for the 4810 models 31x and 32x. If not, how should the 4910 be  
incorporated?  
voltage switch  
D
C
Ethernet  
A
B
Figure 1-3. 31x models rear view connections. Note the location of the voltage selection  
switch.  
USB ports.  
Parallel port. Optionally, you can plug a parallel-interface device into  
this port.  
SVGA display port.  
A
Port for external serial devices, such as a scale or a scanner. This  
port is COM1.  
B
Port for a second external serial device. This port is COM2.  
C
Port for a third serial device, which is 12 V powered.  
D
Port for a fourth serial device, which is 12 V powered.  
1-4 SurePOS Installation and Service  
 
Product introduction  
11-9-2005  
Port for an Ethernet LAN cable.  
Mouse port.  
Port for a PS/2 or compatible keyboard.  
Microphone port.  
Audio input port.  
Port for audio output, such as self-amplified speakers  
power  
Power. The voltage switch allows you to select 100-127 V or  
200-240 V ac.  
Attention  
When installing a new power supply, be sure to set the correct  
input voltage for your area or you will damage the power  
supply. See Figure 1-3 on page 1-4 to locate the voltage  
selection switch.  
Chapter 1. Introduction 1-5  
 
Product introduction  
11-9-2005  
Rear connectors 32x models  
|
Figure 1-4 shows the connections available on the 4810/4910 models 32x:  
Voltage switch  
3
+5 VDC (E+F)  
+12 VDC (E+F)  
E
E
D
A
C
B
Cash  
Drawer  
Ethernet  
Figure 1-4. 32x models rear view connections. Note the location of the voltage selection  
switch.  
USB ports.  
SVGA display port.  
A
Port for external serial devices, such as a scale or  
a scanner. This port is COM1.  
B,C,D  
Ports for second, third, and fourth external serial  
devices.  
E
Port for a fifth serial device, which is 12 V powered.  
F
Port for a sixth serial device, which is 12 V  
powered.  
Port for an Ethernet LAN cable.  
Mouse port.  
Port for a PS/2 or compatible keyboard.  
Microphone port.  
Audio input port.  
1-6 SurePOS Installation and Service  
 
Product introduction  
11-9-2005  
Port for audio output, such as self-amplified  
speakers  
power  
Power. The voltage switch allows you to select  
100-127 V or 200-240 V ac.  
Attention  
When installing a new power supply, be sure  
to set the correct input voltage for your area or  
you will damage the power supply. See  
Figure 1-4 on page 1-6 to locate the voltage  
selection switch.  
Chapter 1. Introduction 1-7  
 
Product introduction  
11-9-2005  
1-8 SurePOS Installation and Service  
11-9-2005  
|
Chapter 2. Disassembling the 4810/4910 SurePOS 300  
|
|
|
This section describes how to disassemble the 4810/4910 SurePOS 300.  
B
A
C
L
H
D
L
G
E
F
|
|
|
Figure 2-1. View of components  
1. Unplug the power cord.  
2. Remove the cover from the unit.  
3. Remove the hard drive (ꢀAꢁ in Figure 2-2 on page 2-2) or compact flash (ꢀBꢁ):  
Note: The unit can accommodate either the hard disk drive or the compact  
flash.  
a. To remove the hard drive, disconnect the power and interface cables from  
the hard drive.  
© Copyright IBM Corp. 2002, 2004  
2-1  
 
11-9-2005  
Figure 2-2. Bracket assembly and hard drive  
b. Using Figure 2-2, follow the directions for either an HDD or flash memory.  
v Press to release the tabs (ꢀJꢁ) on each side of the hard drive (ꢀKꢁ) and  
slide it out of the bracket (ꢀIꢁ).  
v To remove the compact flash:  
1) Disconnect the cables from the compact flash  
2) Remove the screws holding the assembly. Slide the compact flash  
card assembly (ꢀBꢁ in Figure 2-1 on page 2-1 ) to one side and lift  
out.  
4. Using Figure 2-1 on page 2-1, press and lift the clamps (ꢀGꢁ) on each side of  
the dual inline memory module (DIMM) (ꢀHꢁ) to lift it from the socket.  
Note: Removing the central processing unit (CPU) and heat sink is necessary only  
if you are replacing the CPU.  
5. Remove the heat sink (ꢀCꢁ in Figure 2-1 on page 2-1) and the CPU (ꢀDꢁ):  
a. To remove the heat sink, press down and then forward on the clamp.  
b. Break the silicon grease bond by twisting and then lifting the heat sink.  
c. Lift the zero insertion force (ZIF) connector from the CPU.  
d. Remove the CPU from the unit.  
6. Remove the LED assembly (ꢀFꢁ in Figure 2-1 on page 2-1) by removing the  
screws and sliding it to one side.  
7. Remove the power supply (ꢀEꢁ):  
2-2 SurePOS Installation and Service  
 
11-9-2005  
a. Unplug the connector and remove the screws that hold the power supply.  
b. Lift the power supply from the unit.  
Attention  
|
|
|
When installing a new power supply, be sure to set the correct input  
voltage for your area or the power supply will be damaged. See  
Figure 1-3 on page 1-4 to locate the voltage selection switch.  
|
|
|
8. Remove the screws holding the riser card and then remove riser card.  
|
|
|
Figure 2-3. Planar board assembly  
9. Using Figure 2-3 or Figure 2-1 on page 2-1, remove the screws (ꢀLꢁ) holding  
the planar board to the frame.  
10. Remove the RS-232 panel-mounted connector (ꢀMꢁ).  
11. You can now lift the planar board from the unit.  
|
12. To reassemble the 4810/4910 SurePOS 300, reverse this procedure.  
Note: For disassembling instructions for the SureMark printer and other I/O  
bundled with the 4910, please refer to each device’s respective service  
guides.  
Chapter 2. Disassembling the 4810/4910 SurePOS 300 2-3  
 
11-9-2005  
2-4 SurePOS Installation and Service  
11-9-2005  
Chapter 3. Problem determination  
Note: Refer to IBM Safety Information - Read This First, GA27-4004, before  
beginning the procedures in this chapter.  
|
|
|
Both software errors or hardware failures can cause problems with the 4810/4910  
SurePOS 300. This chapter contains troubleshooting information to help you  
determine the cause of a problem and how to solve it.  
Preliminary checklist  
Begin each service call by checking all of the items in this preliminary checklist. If,  
after performing all the steps, a problem still exists, refer to Table 3-1 to continue  
problem determination.  
1. Observe the power light. If it is not on, refer to Table 3-1.  
2. Verify that the cables are securely and correctly connected.  
3. Verify that the I/O devices, which have their own power switches, are connected  
to an ac power outlet that is operating correctly and that the devices are  
powered on.  
4. Verify that the contrast and brightness controls on the video display (if attached)  
are set correctly.  
5. Verify that all installed hardware devices (such as a memory module, feature  
card, printer, or mouse) are connected correctly and securely.  
Table 3-1. 4810/4910 symptoms  
Symptom  
Actions  
The power LED is off.  
1. Verify that the power cord is plugged into both the  
wall outlet and the back of the terminal.  
2. Verify that the voltage switch setting is correct for  
your area.  
3. Verify that the terminal is powered on.  
4. Verify that there is power from the outlet.  
5. Disconnect all attached devices and feature cards  
to determine if one is overloading the power  
supply. If the power light returns, reconnect them  
one at a time to determine the failing  
field-replaceable unit (FRU).  
6. Ensure that all internal cabling and memory  
modules are correctly inserted.  
7. Exchange the power supply.  
8. Exchange the system board.  
Terminal is not operating.  
1. Unplug the power outlet, wait 5 seconds, and then  
power ON. Verify that the power light on the front  
panel is on. Look for any error messages and  
listen for a beep at the completion of the POST.  
2. Check for a blown fuse, a tripped circuit breaker,  
or a power failure.  
3. Verify that all cables are securely connected to  
and inside of the terminal.  
Power on, LED does not light.  
Replace the LED assembly.  
© Copyright IBM Corp. 2002, 2004  
3-1  
 
Problem determination  
11-9-2005  
Note: To troubleshoot problems with the 4610 SureMark Printer, please refer to the  
SureMark Printers Hardware Service Guide, GY27-0355. For other I/O  
devices bundled with the 4910, please refer to each device’s respective  
service guide.  
3-2 SurePOS Installation and Service  
11-9-2005  
Chapter 4. Parts catalog  
This chapter provides parts information available for the Model 31x and 32x system  
units. See the IBM Store Systems: Parts Catalog, for parts information about  
peripheral devices.  
© Copyright IBM Corp. 2002, 2004  
4-1  
 
Parts catalog  
11-9-2005  
Assembly 1: Field-replaceable units  
7
6
4
5
8
3
9
2
1
10  
11  
4-2 SurePOS Installation and Service  
 
Assembly 1: (continued)  
11-9-2005  
Asm– Part  
Index Number  
Units Description  
1–1  
–2  
–2  
–3  
45P6211  
03R5908  
03R5973  
16K9262  
45P6236  
03R5924  
45P6205  
45P6203  
45P6235  
45P6209  
03R5968  
45P6222  
03R5912  
03R5911  
45P6206  
45P6090  
03R5953  
47P9036  
03R5970  
45P6213  
45P6204  
03R5929  
42L0098  
03R5972  
03R5969  
03R5974  
1 LED panel  
1 System board (31x)  
1 System board (32x)  
1 128-MB DIMM  
1 256-MB DIMM  
1 512-MB DIMM  
1 Compact Flash mount  
1 64-MB Compact Flash  
1 128-MB Compact Flash  
1 Riser card (31x, not shown)  
1 Riser card (32x, not shown)  
1 Battery (not shown)  
1 HDD  
1 HDD bracket  
1 HDD cable (not shown)  
1 CPU heat sink (31x)  
1 CPU heat sink and fan (32x)  
1 866 MHz CPU (31x)  
–4  
–5  
–6  
–7  
–8  
–8  
–9  
–9  
–10  
–11  
1 1.2 GHz CPU (32x)  
1 Parts kit (not shown)  
1 100 W power supply  
1 Panel-mounted 15-pin connector  
1 Ethernet cable (not shown)  
1 CD port card (32x, not shown)  
1 Panel-mounted 9-pin serial connector (32x, not shown)  
1 Riser power connector (32x, not shown)  
Note: For a list of field replaceable units for the printer that is bundled with 4910, refer to the SureMark  
Printers Hardware Service Guide, GY27-0355. For other I/O devices bundled with the 4910, please  
refer to each device’s respective service guide.  
Chapter 4. Parts catalog 4-3  
11-9-2005  
4-4 SurePOS Installation and Service  
11-9-2005  
Appendix A. Input/output device commands  
This section lists the commands and their usage.  
Character display (VFD) commands  
The integrated customer display and distributed customer display use the same  
command sets.  
This section describes the following character display commands:  
v Emulation mode select  
v Character set select  
v User character definition  
v Brightness control  
v Alphanumeric message scroll  
v Backspace  
v Horizontal tab  
v Line feed  
v Carriage return  
v Test  
v Display position  
v Normal display  
v Vertical scroll  
v Cursor on  
v Cursor off  
v Reset  
v Null  
Note: The command code format shown in the following topics consists of the hex  
value followed by the ASCII representation of that value within brackets.  
Emulation mode select (00) <NULL>  
00 nn  
Purpose:  
Sets the specified emulation mode.  
00  
Logic Controls Emulation Mode (default)  
IBM mode  
01  
Example:  
This example sets Logic Controls emulation mode:  
00 00  
Character set select (02) <STX>  
Note: This command is effective only in IBM Mode.  
02 nn  
© Copyright IBM Corp. 2002, 2004  
A-1  
 
Input/output device commands  
Purpose:  
11-9-2005  
Selects the specified character set.  
00  
01  
02  
03  
04  
05  
06  
07  
08  
09  
0A  
0B  
Modified IBM code page 437 (U.S./European, power-on default)  
Modified IBM code page 897 (Katakana)  
Modified IBM code page 858 (Multilingual International)  
Modified IBM code page 852 (Central Europe)  
Modified IBM code page 855 (Cyrillic)  
Modified IBM code page 857 (Turkey)  
Modified IBM code page 862 (Israel)  
Modified IBM code page 863 (Canadian French)  
Modified IBM code page 864 (Arabic)  
Modified IBM code page 865 (Nordic)  
Modified IBM code page 808 (Cyrillic - Russia)  
Modified IBM code page 869 (Greece)  
Example:  
This example selects the U.S./European character set:  
02 00  
User character definition (03) <EXT>  
03 nn  
Purpose:  
Defines a custom character.  
Logic Controls Emulation Mode  
The byte that follows the command byte contains an ASCII  
character between X'20' and X'7F' of a keyboard key to be  
redefined. This byte is followed by five bytes defining the bit  
patterns of the user-defined character. Logic Controls Emulation  
Mode allows only one keyboard key to be redefined. This means  
that there is only one user-definable character in this mode. Once a  
key is redefined, any occurrence of that character on the display  
will change to the user-defined character. If a new key is redefined,  
the previously redefined key is restored to the original character in  
all places on the display and the newly redefined key is changed to  
the user-definable character. Table A-1 on page A-3 shows the  
format of these five bytes.  
|
|
|
|
|
Note: A hyphen character in the table indicates a do-not-care bit.  
The other values relate to the character pixel positions  
shown in the diagram following the table. A value of 1 in the  
data stream indicates that the related pixel position is ON; a  
0 indicates that it is OFF.  
A-2 SurePOS Installation and Service  
 
Input/output device commands  
11-9-2005  
Table A-1. User character definition: Logic Controls Emulation  
Mode  
Bit  
Byte #  
0
1
2
3
4
5
6
7
1
2
3
4
5
P8  
P7  
P6  
P5  
P4  
P3  
P2  
P1  
P16 P15 P14 P13 P12 P11 P10 P9  
P24 P23 P22 P21 P20 P19 P18 P17  
P32 P31 P30 P29 P28 P27 P26 P25  
-
-
-
-
-
P35 P34 P33  
* These character definitions are maintained for application compatibility  
with displays with 5x8 character boxes.  
– –– –5 pixels wide – – – –→  
P1  
P6  
P2  
P7  
P3  
P8  
P4  
P9  
P5  
P10  
|
P11 P12 P13 P14 P15  
|
P16 P17 P18 P19 P20 7 pixels high  
P21 P22 P23 P24 P25  
P26 P27 P28 P29 P30  
P31 P32 P33 P34 P35  
|
|
IBM Mode  
IBM Mode allows nine user defined characters to be defined. See  
Table A-2 for defined characters:  
Table A-2. User character definition: IBM Mode  
1. X'15'  
2. X'16'  
3. X'17'  
4. X'18'  
5. X'19'  
6. X'1A'  
7. X'1C'  
8. X'1D'  
9. X'1E'  
The byte that follows the command byte represents an address  
betweenX'15' and X'1A', or between X'1C' and X'1E' in the currently  
selected character set. This byte is followed by eight bytes, which  
define the actual bit patterns of the user-defined character.  
Table A-3 on page A-4 shows the format of these eight bytes.  
Note: A hyphen character in the table indicates a do-not-care bit.  
The other values relate to the character pixel positions  
shown in the diagram following the table. A value of 1 in the  
appropriate place in the data stream indicates that the  
related pixel position is ON; a 0 indicates that it is OFF.  
Appendix A. Input/output device commands A-3  
 
Input/output device commands  
11-9-2005  
Table A-3. User character definition: IBM emulation mode  
Bit  
Byte #  
0
1
2
3
4
5
6
7
1
2
3
4
5
6
7
8*  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
P1  
P6  
P2  
P7  
P3  
P8  
P4  
P9  
P5  
P10  
P11 P12 P13 P14 P15  
P16 P17 P18 P19 P20  
P21 P22 P23 P24 P25  
P26 P27 P28 P29 P30  
P31 P32 P33 P34 P35  
-
-
-
-
-
* These user character definitions are maintained for application  
compatibility with displays with 5x8 character boxes.  
– – – –5 pixels wide – – – –→  
P1  
P6  
P2  
P7  
P3  
P8  
P4  
P9  
P5  
P10  
|
P11 P12 P13 P14 P15  
|
P16 P17 P18 P19 P20 7 pixels high  
P21 P22 P23 P24 P25  
P26 P27 P28 P29 P30  
P31 P32 P33 P34 P35  
|
|
Brightness control (04) <EOT>  
04 nn  
Purpose:  
Specifies a brightness setting for the display, in a percentage. The power-on  
default is 100%.  
X'FF'  
100%  
X'60'  
X'40'  
X'20'  
60%  
40%  
20%  
Alphanumeric message scroll (05) <ENG>  
05 xxx...  
Purpose:  
Specifies a message of up to 45 characters to continuously scroll across  
the top line of the display. (Any text on the bottom line does not change.)  
Data received after the 45th character are ignored except for a carriage  
return (X'0D'). The message starts to display when the carriage return  
command is received. If the cursor position is on the top line when this  
command is received, it is moved to the first position on the bottom line. If it  
is on the bottom line, its position does not change. Data continues scrolling  
on the top line until a valid character (backspace, horizontal tab, line feed,  
A-4 SurePOS Installation and Service  
 
Input/output device commands  
11-9-2005  
carriage return, or display position command is written to the top line. The  
test and reset commands stop the scrolling message regardless of the  
display position.  
Backspace (08) <BS>  
08  
Purpose:  
Decrements the cursor position by one and clears any character displayed  
in that position. If the write position is at the lower left, the position is moved  
to the upper right, and if it is at the upper left, it is moved to the lower right.  
This commands stops the scrolling alphanumeric message if the cursor  
position is on the top line when this command is sent.  
Horizontal tab (09) <HT>  
09  
Purpose:  
Increments the cursor position by one. No characters are erased. This  
command stops the scrolling message if the cursor position is on the top  
line when the command is sent. At the end of a line, the display behavior is  
determined by the state of the display control mode as follows:  
Normal Display Control Mode (DC1)  
If the cursor is at the upper right position, it is moved to the lower  
left position. If the cursor is at the lower right position, it is moved to  
the upper left position.  
Vertical Scroll Display Control Mode (DC2)  
If the cursor is at the upper right position, it is moved to the lower  
left position. If the cursor is at the lower right position, the  
characters displayed on the bottom line are moved to the top line,  
the bottom line is cleared, and the cursor is moved to the lower left  
position.  
Line feed (0A) <LF>  
0A  
Purpose:  
The display behavior is determined by the state of the display control mode  
as follows:  
Normal Display Control Mode (DC1)  
The cursor is moved to the same position in the complementary  
line. In this mode, a line-feed command stops the scrolling  
alphanumeric message if the cursor is on the top line when this  
command is sent.  
Vertical Scroll Display Control Mode (DC2)  
If the cursor is on the top line, it is moved to the complementary  
position on the bottom line. If the cursor position is on the bottom  
line, all characters on that line are moved to the top line, the bottom  
Appendix A. Input/output device commands A-5  
 
Input/output device commands  
11-9-2005  
line is cleared, and the cursor position is unchanged. This  
command always stops the scrolling alphanumeric message.  
Carriage return (0D) <CR>  
0D  
Purpose:  
Causes the cursor to move to the leftmost position of the current line. This  
command stops the scrolling alphanumeric message if the cursor position is  
on the top line when this command is sent.  
Test (0F) <SI>  
0F  
Purpose:  
Causes the first 40 characters in the currently selected character set to be  
displayed once. At the end of the test, a test pattern is written that turns all  
pixels ON. At the end of the test, the display is cleared and is reset to the  
power-on state as described at “Reset (1F) <US>” on page A-7.  
Display position (10) <DLE>  
10 nn  
Purpose:  
Changes the cursor position. The byte that follows the command byte  
indicates the character position where the next data-string write operation is  
to start. Any values greater than X'27' are ignored and the cursor position  
remains unchanged. This command stops the scrolling alphanumeric  
message if the cursor position is on the top line when this command is  
sent.  
X'00'  
X'13'  
X'14'  
X'27'  
Top left  
Top right  
Bottom left  
Bottom right  
Normal-display control mode (11) <DC1>  
11  
Purpose:  
Sets normal display-control mode (DC1) and permits data to be written to  
either line. After a character is written, the cursor moves one position to the  
right. When the display position is at the last position of the top line, the  
cursor moves to the first position of the bottom line. When the display  
position is at the last position of the bottom line, the cursor moves to the  
first position of the top line. The display remains in DC1 mode until a DC2  
mode command is issued, a reset command is issued, or power is removed  
from the display.  
A-6 SurePOS Installation and Service  
 
Input/output device commands  
11-9-2005  
Vertical-scroll display control mode (12) <DC2>  
12  
Purpose:  
Sets vertical-scroll display control mode (DC2) and permits data to be  
written to either line. When the display position is at the last position of the  
top line, the cursor moves to the first position of the bottom line. When  
either valid character data or a Horizontal Tab command is sent to the last  
position of the bottom line, the data on the bottom line is transferred to the  
top line and the cursor is moved to the lower left position. Note that a  
Carriage Return command does not cause the data on the bottom line to be  
transferred to the top line. This mode is the default setting for power on and  
reset. The display remains in DC2 mode until a DC1 mode command is  
issued.  
Cursor on (13) <DC3>  
13  
Purpose:  
Turns on the cursor. The command is the power-on default setting.  
Cursor off (14) <DC4>  
14  
Purpose:  
Turns off the cursor.  
Reset (1F) <US>  
1F  
Purpose:  
Causes the display to reset some programmable parameters to the  
power-on state, which is defined as:  
v Cursor on.  
v Scrolling alphanumeric message off.  
v All character positions filled with X'20'.  
v Write position for next write at position X'00' (top left).  
v Default code page (437) selected.  
v DC2 mode enabled.  
v Default (Logic Controls) emulation mode selected.  
v Brightness set to 100%.  
v IBM user-defined characters not erased. The Logic Controls user-defined,  
character key is reset.  
All byte values between X'00' and X'1F' not defined in this section are ignored by  
the display in Logic Controls mode. User-defined characters in the IBM mode that  
have not been defined previously are spaces.  
Appendix A. Input/output device commands A-7  
 
Input/output device commands  
11-9-2005  
Null VFD Commands  
(06), (1B, 06), (07), (1B), 07)  
Purpose:  
These are null commands for both integrated and distributed display  
modules. They will have no effect on the operation of the display.  
A-8 SurePOS Installation and Service  
 
Input/output device commands  
11-9-2005  
APA commands  
This section describes the following APA VFD commands:  
v Backspace without deleting  
v Line feed  
v Carriage return  
v Test  
v Clear display  
v Display position  
v Delete to end of line  
v Dimming  
v Cursor mode  
v Screen mode  
v Horizontal scroll  
v Display mode  
v User definable font  
v Graphic display mode  
v Double-size letter in horizontal  
v Character code set of full-size letter  
v Character code set of half-size letter  
v Horizontal scroll on all lines  
v Font selection  
v Null  
Note: The command code format shown in the following topics is in hexadecimal  
format.  
Backspace without deleting  
08  
Purpose:  
The write-in position is shifted to the left one digit and the displaying screen  
is not changed. This command is ignored when the write-in position is on  
the least significant digit.  
Line feed  
0A  
Purpose:  
The write-in position is shifted to the next row on the same digit position. If  
the write-in position is on the bottom row, the displayed character is scrolled  
up to the upper row. All characters on the bottom row are cleared. The  
write-in position is not changed. The displayed character under the screen  
mode of the 24x24-dot 1 row+16x16-dot 2 rows is not scrolled up from the  
row of 16x16-dot format to 24x24-dot.  
Appendix A. Input/output device commands A-9  
 
Input/output device commands  
11-9-2005  
Carriage return  
0D  
Purpose:  
The write-in position is shifted to the most significant digit of the same row.  
If the write-in position is on the most significant digit, the command is  
ignored.  
Test  
0F  
Purpose:  
Causes the 40 characters in the IBM code page 437 character (X'20'-X'47')  
set to be displayed one time. In addition, at the end of the test, a test  
pattern is written that turn all pixels.  
When Test is working, all codes are ignored. The test command X'OF' is  
only available when the IBM code page 437 is selected.  
When the other font table except IBM code page 437 is selected, test code  
is ignored.  
Clear display  
(1B), (5B, 32), (4A)  
Purpose:  
All the displayed characters are erased. The write-in position is not  
changed.  
Display position  
1B 5B Py 3B Px 48  
Purpose:  
Instead of writing the character from the first digit, use this command to  
specify the write-in start position. The write-in position is shifted with Py and  
Px and is based on the half-size letter of the font, which is specified with  
the Screen Mode command. Py indicates the position of the row and Px the  
digit. Py and Px must be defined under the following conditions:  
v If Py is 0, it is set to 1 (X'31').  
v If Py is greater than the bottom row, it is set to the bottom row.  
v If Px is 0, it is set to 1 (X'31').  
v If Px is greater than the least digit, it is set to the least digit.  
A special form of the display position command exists (1B 5B 48 27),  
which sets the write-in position to the home position (Py=1 and Px=1).  
Delete to end of line  
1B 5B 30 4B  
A-10 SurePOS Installation and Service  
 
Input/output device commands  
11-9-2005  
Purpose:  
The displayed characters from the write-in position to the end position on  
the same row are erased. The write-in position is not shifted.  
Dimming  
1B 5C 3F 4C 44 Ps  
Purpose:  
Luminance can be adjusted into six levels by using this command. The data  
byte following the command sequence (represented by Ps in the preceding  
command format), changes the dimming level. When the module is turned  
on, the level is set to 5 (100%).  
Ps  
Luminance %  
0 (X'30')  
0
1 (X'31') 31.6  
2 (X'32') 45  
3 (X'33') 58.8  
4 (X'34') 79.4  
5 (X'35') 100 (default)  
Cursor mode  
1B 5C 3F 4C 43 Ps  
Purpose:  
This command is only available in 5x7-dot screen mode. The data byte  
following the command sequence (represented by Ps in the preceding  
command format), changes the cursor mode. The cursor is always  
displayed at the write-in position. The cursor is formed by five dots that are  
located at the bottom of 5x7-dot matrix character font.  
Ps  
Mode  
0 (X'30') No lighting (default)  
1 (X'31') Blinking  
2 (X'32') Lighting  
No Lighting  
Blinking  
The cursor does not display. This is the default setting  
when power is turned on.  
The cursor flashes ON and OFF every 0.3 seconds at the  
blank digit.  
Lighting  
The cursor displays. If the write-in position is assigned to  
the position at which a character is displaying, the cursor  
displays instead of the character.  
Screen mode  
1B 5C 3F 4C 53 Ps  
Purpose:  
The data byte following the command sequence (represented by Ps in the  
preceding command format), changes the screen mode.  
Appendix A. Input/output device commands A-11  
 
Input/output device commands  
11-9-2005  
Ps  
Mode  
6 (X'36') 5x7 dots, 4 rows (default)  
7 (X'37') 5x7 dots, 5 rows  
8 (X'38') 16x16 dots, 2 rows  
Horizontal scroll  
1B 5C 3F 4C 48 Pm 3B Pl 3B Pt 3B Pn 3B Pd...Pd  
Purpose:  
This command initiates horizontal scrolling. The control bytes embedded in  
the command sequence (represented by Pm, Pl, Pt, and Pn in the  
preceding command format), change the scrolling characteristics. Pd...Pd  
represents the data bytes.  
Pm  
Pl  
6 (X'36'): 5x7 dots, 4 rows  
7 (X'37'): 5x7 dots, 5 rows  
8 (X'38'): 16x16 dots, 2 rows  
1 4 (X'31' X'34'): Pm=6  
1 5 (X'31' X'35'): Pm=7  
1, 2 (X'31', X'32'): Pm=8  
Pt  
1 (X'31'): 1 line/10 ms  
1 (X'32'): 1 line/20 ms  
Pn  
The number of data bytes (1 for half-size letter, 2 for full-size letter,  
maximum is 128 (X'80').  
Pd...Pd The data characters.  
The following list explains how the horizontal scroll command operates:  
v When a character is displayed on the line selected for scroll mode, all  
displaying characters and the display mode set command are erased.  
v A character scrolls by closed loop until the cancel command is selected.  
In this case, the same message is scrolled repeatedly with no space.  
v A screen scrolls from right to left, dot by dot.  
v The scrolled display range is defined by the screen mode setting.  
v The command is canceled when Pn = X'00'. After it is canceled,  
displayed characters are cleared, and the write-in position moves to the  
most significant digit of the row.  
v The command can be started only on a single line.  
v A character’s display mode set command (reverse, blinking, and so on)  
can be added with the display data frame. If the command is written two  
or more times in one scroll data frame, only the first command is valid;  
others are ignored.  
v When message data is changed, you must reissue this command. While  
scrolling, the user definable font set command is not available.  
Display mode set  
1B 5B Ps 6D  
Purpose:  
This command sets the display mode characteristics. The control byte  
embedded in the command sequence (represented by Ps) sets the mode.  
A-12 SurePOS Installation and Service  
 
Input/output device commands  
11-9-2005  
Ps  
Mode  
0 (X'30') Reset display mode. Characters written after this command are reset  
to normal display mode.  
5 (X'35)' Blinking mode. Characters written after this command blink ON and  
OFF every 0.3 seconds.  
7 (X'37') Reverse mode. Characters written after this command are reversed.  
User-definable font set  
1B 5C 3F 4C 57 Pf 3B Pn 3B Pc 3B Pd...Pd  
Purpose:  
This command specifies a user-definable font set. The control bytes  
embedded in the command sequence (represented by Pf, Pn, and Pc in the  
preceding command format), change the font characteristics. Pd...Pd  
represents the font data bytes.  
Pf (font size)  
1 (X'31'): 5x7 dots (ANK)  
2 (X'32'): 8x16 dots  
3 (X'33'): 16x16 dots  
Pn (font number) 1 32 (X'31' X'33', X'32') Pf=1, 2  
1 16 (X'31' X'31', X'36') Pf=3  
Pc (registration  
address)  
2 hex digits Pf=1, 2  
4 hex digits (Pf=3)  
Pd...Pd  
2 hex digits x 7 Pf=1  
2 hex digits x 16 Pf=2  
2 hex digits x 2 x 16 Pf=3  
Note: All data is stored into RAM. You must issue this command every  
time you switch ON the power.  
Available registration address can be established as follows:  
1. Font size 5x7  
At the all language  
X'20'--X'FF'  
2. Font size 8x16  
English  
X'01'--X'FF' (except X'08', X'0A', X'OD', X'1B')  
Japanese  
X'20'--X'7F', X'A0'--X'DF'  
Korean, Simplified Chinese and Traditional Chinese  
X'20'~ X'A0'  
3. Font size 16x16  
Japanese JIS X 0208-1990 (Font selection X'1B', X'53', X'31')  
X'8140'--X'81FF', X'8240'--X'84FF' (Positions X'8200'--X'823F' are not  
available.)  
X'8840'--X'88FF', X'8940'--X'9FFF' (Positions X'8900'--X'893F' are not available.)  
X'E040'--X'E0FF', X'E140'--X'EAFF' (Positions X'E100'--X'E13F' are not  
available.)  
Korean KS C 5601-1992 (Font selection X'1B', X'53', X'32')  
X'A1A0'--X'A1FF', X'A2A0'--X'ACFF' (Positions X'8200'--X'829F' are not  
Appendix A. Input/output device commands A-13  
 
Input/output device commands  
available.)  
11-9-2005  
X'B0A0'--X'B0FF', X'B1A0'--X'C8FF' (Positions X'B100'--X'B19F' are not  
available.)  
X'CAA0'--X'CAFF', X'CBA0'--X'FDFF' (Positions X'CB00'--X'CB9F' are not  
available.)  
Simplified Chinese GB2312-80 (Font selection X'1B', X'53', X'33')  
X'A1A0'--X'A1FF', X'A2A0'--X'A9FF' (Positions X'A200'--X'A29F' are not  
available.)  
X'B0A0'--X'B0FF', X'B1A0'--X'F7FF' (Positions X'B100'--X'B19F' are not  
available.)  
Traditional Chinese Big-5 (Font selection X'1B', X'53', X'34')  
X'A140'--X'A1FF', X'A2A0'--X'C6FF' (Positions X'A200'--X'A23F' are not  
available.)  
X'C940'--X'C9FF', X'CA40'--X'F9FF' (Positions X'CA00'--X'CA3F' are not  
available.)  
Graphic display mode  
1B 5C 3F 4C 47 Px 3B Py 3B Ph 3B Pw 3B Pd  
Purpose:  
This command specifies the graphic display mode. The control bytes  
embedded in the command sequence (represented by Px, Py, Ph, and Pw  
in the command format), change the graphic display characteristics. Pd  
represents the data byte.  
Px (display  
0 159 (X'30' X'31', X'35', X'39')  
position)  
Py (display  
position)  
Ph (height)  
Pw (width)  
Pd  
0 39 (X'30' X'33', X'39')  
1 40 (X'31' X'34', X'30')  
1 160 (X'31' X'31', X'36', X'30')  
The display data.  
Double-size letter in horizontal  
1B 23 Ps  
Purpose:  
This command sets a character with double-size letter in horizontal. It is  
available for all full-size letter, all half-size letter, and ANK font.  
Ps  
5 = Normal-size letter  
6 = Double-size letter in horizontal  
Horizontal scroll on all lines  
The format of the Horizontal Scroll Select command is as follows:  
1B 5C 3F 4C 4D 53  
Purpose:  
This command sets horizontal scroll mode.  
A-14 SurePOS Installation and Service  
 
Input/output device commands  
The format of the Horizontal Scroll Release command is as follows:  
11-9-2005  
1B 5C 3F 4C 4D 45  
Purpose:  
This command resets horizontal scroll mode.  
The format of the Horizontal Scroll Display Mode Set command is as follows:  
1B 5C 3F 4C 4D Pm 3B Pl 3B Pt 3B Pn 3B Pd...Pd  
Purpose:  
This command sets horizontal scrolling options. The control bytes  
embedded in the command sequence (represented by Pm, Pl, Pt, and Pn in  
the preceding command format), change the scrolling characteristics.  
Pd...Pd represent the data bytes. This command does not affect previous  
display settings.  
Pm (screen  
6 (X'36'): 5x7 dots, 4 rows  
mode)  
7 (X'37'): 5x7 dots, 5 rows  
8 (X'38'): 16x16 dots, 8x16 dots, 2 rows  
Pl (row)  
1 4 (X'31'X'34'): Pm=6  
1 5 (X'31'X'35'): Pm=7  
1 2 (X'31'X'32'): Pm=8  
Pt (scroll  
speed)  
1 (X'31'): 1 digit/10 ms  
1 (X'32'): 1 digit/20 ms  
Pn (number  
of characters)  
Pd...Pd  
The number of data bytes (1 for half size letter, 2 for full size letter,  
maximum is 128 (X'80').  
This represents the data characters.  
The format of the Horizontal Scroll Start command is as follows:  
1B 5C 3F 4C 4D 47  
Purpose:  
This command begins horizontal scrolling on all lines. All  
subsequent commands are ignored until a Scroll Mode Release  
command is sent.  
The rules of operation for the Horizontal Scroll On All Lines are as follows:  
v Any codes not described here are ignored.  
v The most recent Display Mode Set command becomes effective in one  
screen scroll setting before the Scroll Start command is performed.  
v A screen scrolls from right to left, dot by dot.  
v The range of the display that is being scrolled is defined by the screen  
mode setting.  
v The command is canceled when Pn = X'00'. After it is canceled,  
displayed characters are cleared, and the write-in position moves to the  
most significant digit of the row.  
v The command can be started only on a single line.  
v A character’s Display Mode Set command (reverse, blinking, and so on)  
can be added with the display data frame. If the command is written  
twice or more in one scroll data frame, only the first command is valid;  
others are ignored.  
Appendix A. Input/output device commands A-15  
Input/output device commands  
11-9-2005  
v When message data is changed, you must reissue this command. While  
scrolling, the User Definable Font Set command is not available.  
v Space data is written in the other rows except those selected with the Pl  
code.  
Font selection  
1B 53 Pn  
Purpose:  
Selects the language font to use  
The command stream is as follows:  
Pn 30: English - IBM code page 437 modified (default)  
31: Japanese - JIS X 0208-1990  
32: Korean - KS C 5601-1992  
33: Simplified Chinese - GB-2321  
34: Traditional Chinese - BIG5  
Null Commands  
(06), (1B, 06), (07), (1B, 07)  
Purpose:  
These are null commands for both integrated and distributed display  
modules. They have no effect on the operation of the display.  
A-16 SurePOS Installation and Service  
 
11-9-2005  
Appendix B. Notices  
References in this publication to IBM products, programs, and services do not imply  
that IBM intends to make these available in all countries in which IBM operates. Any  
reference to an IBM product, program, or service is not that only IBM’s product,  
program, or service may be used. Any functionally equivalent product, program, or  
service that does not infringe any of IBM’s intellectual property rights may be used  
instead of the IBM product, program, or service. Evaluation and verification of  
operation in conjunction with other products, except those expressly designated by  
IBM, are the user’s responsibility.  
IBM may have patents or pending patent applications covering the subject matter in  
this document. The furnishing of this document does not give you any license to  
these patents. You can send license inquiries, in writing, to:  
IBM Director of Licensing  
IBM Corporation  
North Castle Drive  
Armonk, NY 10504-1785  
U.S.A.  
The following paragraph does not apply to the United Kingdom or any other country  
where such provisions are inconsistent with local law: INTERNATIONAL BUSINESS  
MACHINES CORPORATION PROVIDES THIS PUBLICATION AS ISWITHOUT  
WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT  
NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,  
MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE. Some states  
do not allow disclaimer of express or implied warranties in certain transactions,  
therefore, this statement may not apply to you.  
This information could include technical inaccuracies or typographical errors.  
Changes are periodically made to the information herein; these changes will be  
incorporated in new editions of the publication. IBM may make improvements and/or  
changes in the product(s) and/or program(s) described in this publication at any  
time without notice.  
Any references in this information to non-IBM Web sites are provided for  
convenience only and do not in any manner serve as an endorsement of those  
Web sites. The materials at those Web sites are not part of the materials for this  
IBM product and use of those Web sites is at your own risk.  
Information concerning non-IBM products was obtained from the suppliers of those  
products, their published announcements or other publicly available sources. IBM  
has not tested those products and cannot confirm the accuracy of performance,  
compatibility or any other claims related to non-IBM products. Questions on the  
capabilities of non-IBM products should be addressed to the suppliers of those  
products.  
© Copyright IBM Corp. 2002, 2004  
B-1  
 
11-9-2005  
Electronic emission notices  
Federal communications commission (FCC) statement  
This equipment has been tested and found to comply with the limits for a Class A  
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to  
provide reasonable protection against harmful interference when the equipment is  
operated in a commercial environment. This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed and used in accordance with the  
instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful  
interference, in which case the user will be required to correct the interference at  
his own expense.  
Properly shielded and grounded cables and connectors must be used in order to  
meet FCC emission limits. IBM is not responsible for any radio or television  
interference caused by using other than recommended cables and connectors or by  
unauthorized changes or modifications to this equipment. Unauthorized changes or  
modifications could void the user’s authority to operate the equipment.  
This device complies with part 15 of the FCC Rules. Operation is subject to the  
following two conditions: (1) this device may not cause harmful interference, and (2)  
this device must accept any interference received, including interference that may  
cause undesired operation.  
Industry Canada class A emission compliance statement  
This Class A digital apparatus complies with Canadian ICES-003.  
Avis de conformité aux normes d’Industrie Canada  
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du  
Canada.  
European Community (CE) mark of conformity statement  
This product is in conformity with the protection requirements of EC Council  
Directive 89/336/EEC on the approximation of the laws of the Member States  
relating to electromagnetic compatibility. IBM cannot accept responsibility for any  
failure to satisfy the protection requirements resulting from a non-recommended  
modification of the product, including the fitting of non-IBM option cards.  
This product has been tested and found to comply with the limits for Class A  
Information Technology Equipment according to CISPR 22 / European Standard EN  
55022. The limits for Class A equipment were derived for commercial and industrial  
environments to provide reasonable protection against interference with licensed  
communication equipment.  
Warning: This is a Class A product. In a domestic environment this product may  
cause radio interference, in which case the user may be required to take adequate  
measures.  
Germany  
Zulassungsbescheinigung laut dem Deutschen Gesetz über die  
elektromagnetische Verträglichkeit von Geräten (EMVG) vom 30. August 1995  
(bzw. der EMC EG Richlinie 89/336).  
B-2 SurePOS Installation and Service  
 
11-9-2005  
Dieses Gerät ist berechtigt. in Übereinstimmung mit dem Deutschen EMVG das  
EG-Konformitätszeichen - CE - zu führen.  
Verantwortlich für die Konformitätserklärung nach Paragraph 5 des EMVG ist die  
IBM Deutschland Informationssysteme GmbH, 70548 Stuttgart.  
Informationen in Hinsicht EMVG Paragraph 3 Abs. (2) 2:  
Das Gerät erfüllt die Schutzanforderungen nach EN 50082–1 und EN 55022 Klasse A.  
EN 55022 Klasse A Geräte müssen mit folgendem Warnhinweis versehen werden:  
Warnung: dies ist eine Einrichtung der Klasse A. Diese Einrichtung kann im  
Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom Betreiber  
verlangt werden, angemessene Maβnahmen durchzuführen und dafür  
aufzukommen.″  
EN 50082–1 Hinweis:  
Wird dieses Gerät in einer industriellen Umgebung betrieben (wie in EN 50082–2  
festgelegt), dann kann es dabei eventuell gestört werden. In solch einem Fall ist der  
Abstand bzw. die Abschirmung zu der industriellen Störquelle zu vergröβern.″  
Anmerkung:  
Um die Einhaltung des EMVG sicherzustellen, sind die Geräte, wie in den IBM  
Handbüchern angegeben, zu installieren und zu betreiben.  
Australia / New Zealand  
Attention: This is a Class A product. In a domestic environment this product may  
cause radio interference, in which case the user may be required to take adequate  
measures.  
Japanese power line harmonics compliance statement  
Japanese Voluntary Control Council for Interference (VCCI) statement  
This product is a Class A Information Technology Equipment and conforms to the  
standards set by the Voluntary Control Council for Interference by Technology  
Equipment (VCCI). In a domestic environment this product may cause radio  
interference in which case the user may be required to take adequate measures.  
Appendix B. Notices B-3  
 
11-9-2005  
Korean Communications Statement  
Please note that this device has been approved for business purposes with regard  
to electromagnetic interference. If you find this is not suitable for your use, you may  
exchange it for a non-business purpose one.  
Taiwanese class A warning statement  
Taiwanese battery recycling statement  
Waste batteries, please recycle.  
B-4 SurePOS Installation and Service  
 
11-9-2005  
Chinese Class A warning statement  
Attention: This is a Class A product. In a domestic environment this product may  
cause radio interference in which case the user may be required to take adequate  
measures.  
Electrostatic discharge (ESD)  
Attention: ESD damage can occur when there is a difference in charge between  
the part, the product, and the service person. No damage will occur if the service  
person and the part being installed are at the same charge level.  
ESD Damage Prevention  
Anytime a service action involves physical contact with logic cards, modules,  
back-panel pins, or other ESD sensitive (ESDS) parts, the service person must be  
connected to an ESD common ground point on the product through the ESD wrist  
strap and cord.  
The ESD ground clip can be attached to any frame ground, ground braid, green  
wire ground, or the round ground prong on the AC power plug. Coax or connector  
outside shells can also be used.  
Handling Removed Cards  
Logic cards removed from a product should be placed in ESD protective containers.  
No other object should be allowed inside the ESD container with the logic card.  
Attach tags or reports that must accompany the card to the outside of the container.  
Appendix B. Notices B-5  
 
11-9-2005  
Trademarks  
The following terms are trademarks of International Business Machines Corporation  
in the United States, other countries, or both:  
IBM  
IBM (logo)  
PS/2  
SurePoint  
SurePOS  
Microsoft, Windows, and Windows NT are trademarks of Microsoft Corporation in  
the United States, other countries, or both.  
Other company, product, or service names may be trademarks or service marks of  
others.  
B-6 SurePOS Installation and Service  
 
11-9-2005  
Appendix C. Safety information  
Danger:  
Before you begin to install this product, read the safety information in IBM  
Safety Information — Read This First, GA27-4004. This booklet describes safe  
procedures for cabling and plugging in electrical equipment.  
Gevaar:  
Voordat u begint met de installatie van dit produkt, moet u eerst de  
veiligheidsinstructies lezen in de brochure Veiligheidsinstructies—Lees dit  
eerst, GA27-4004. Hierin wordt beschreven hoe u electrische apparatuur op  
een veilige manier moet bekabelen en aansluiten.  
© Copyright IBM Corp. 2002, 2004  
C-1  
 
11-9-2005  
Perigo:  
Antes de começar a instalar este produto, leia as informações de segurança  
contidas em Informações Sobre Seguranaça—Leia Isto Primeiro, GA27-4004.  
Esse folheto descreve procedimentos de segurança para a instalação de  
cabos e conexões em equipamentos elétricos.  
Fare!  
Før du installerer dette produkt, skal du læse sikkerhedsforskrifterne i  
Sikkerhedsforskrifter—Lœs dette først GA27-4004. Vejledningen beskriver den  
fremgangsmåde, du skal bruge ved tilslutning af kabler og udstyr.  
Gevaar  
Voordat u begint met het installeren van dit produkt, dient u eerst de  
veiligheidsrichtlijnen te lezen die zijn vermeld in de publikatie IBM Safety  
Information — Read This First, GA27-4004. In dit boekje vindt u veilige  
procedures voor het aansluiten van elektrische appratuur.  
C-2 SurePOS Installation and Service  
11-9-2005  
VAARA  
Ennen kuin aloitat tämän tuotteen asennuksen, lue julkaisussa  
Turvaohjeet—Luetämä ensin, GA27-4004, olevat turvaohjeet. Tässä kirjasessa  
on ohjeet siitä, miten sähkölaitteet kaapeloidaan ja kytketään turvallisesti.  
Danger  
Avant d’installer le présent produit, consultez le livret Informations pour la  
sécurité–Lisez-moi d’abord, GA27-4004, qui décrit les procédures à respecter  
pour effectuer les opérations de câblage et brancher les équipements  
électriques en toute sécurité.  
Vorsicht  
Bevor mit der Installation des Produktes begonnen wird, die  
Sicherheitshinweise in Sicherheitsinformationen—Bitte zuerst lesen, IBM Form  
GA27-4004. Diese Veröffentlichung beschreibt die Sicherheitsvorkehrungen für  
das Verkabeln und Anschlieβen elektrischer Geräte.  
Vigyázat  
Mielôtt megkezdi a berendezés üzembe helyezését, olvassa el a IBM Safety  
Information — Read This First, GA27-4004 könyvecskében leírt biztonsági  
információkat. Ez a könyv leírja, milyen biztonsági intézkedéseket kell  
megtenni az elektromos berendezés huzalozásakor illetve csatlakoztatásakor.  
Appendix C. Safety information C-3  
11-9-2005  
Pericolo  
prima di iniziare l’installazione di questo prodotto, leggere le informazioni  
relative alla sicurezza riportate nell’opuscolo Informazioni di sicurezza—Prime  
informazioni da leggere in cui sono descritte le procedure per il cablaggio ed il  
collegamento di apparecchiature elettriche.  
Fare  
Før du begynner å installere dette produktet, må du lese  
sikkerhetsinformasjonen i Sikkerhetsinformasjon—Les dette først, GA27-4004  
som beskriver sikkerhetsrutinene for kabling og tilkobling av elektrisk utstyr.  
Perigo  
Antes de iniciar a instalação deste produto, leia as informações de segurança  
Informações de Segurança—Leia Primeiro, GA27-4004. Este documento  
descreve como efectuar, de um modo seguro, as ligações eléctricas dos  
equipamentos.  
Peligro  
Antes de empezar a instalar este producto, lea la información de seguridad en  
Información de Seguridad—Lea Esto Primero, GA27-4004. Este documento  
describe los procedimientos de sequridad para cablear y enchufar equipos  
eléctricos.  
C-4 SurePOS Installation and Service  
11-9-2005  
Varning—livsfara  
Innan du börjar installera den här produkten bör du läsa  
säkerhetsinformationen i dikumentet Säkerhetsföreskrifter—Läs detta först,  
GA27-4004. Där beskrivs hur du på ett säkert sätt ansluter elektrisk utrustning.  
Appendix C. Safety information C-5  
11-9-2005  
IBM  
IBM  
GA27-4004  
GA27-4004  
C-6 SurePOS Installation and Service  
11-9-2005  
GA27-4004  
IBM  
GA27-4004  
GA27-4004  
GA27-4004  
GA27-4004  
GA27-4004  
Appendix C. Safety information C-7  
11-9-2005  
C-8 SurePOS Installation and Service  
11-9-2005  
Index  
Numerics  
E
4810 SurePOS 300  
4910 SurePOS 300  
A
F
audio  
features  
B
G
C
commands  
H
I
input/output (I/O)  
device commands  
installation  
D
K
© Copyright IBM Corp. 2002, 2004  
X-1  
 
11-9-2005  
L
LED assembly  
S
M
symptom table  
symptoms  
N
notices  
T
V
O
P
W
Z
power  
power supply  
R
X-2 SurePOS Installation and Service  
Readers’ Comments — We’d Like to Hear from You  
SurePOS 300  
Installation and Service Guide for 4810/4910  
Model 31x, 32x, W2H  
Publication No. GA27-4309-01  
Overall, how satisfied are you with the information in this book?  
Very Satisfied  
h
Satisfied  
h
Neutral  
h
Dissatisfied  
h
Very Dissatisfied  
h
Overall satisfaction  
How satisfied are you that the information in this book is:  
Very Satisfied  
Satisfied  
Neutral  
h
Dissatisfied  
Very Dissatisfied  
Accurate  
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
h
Complete  
h
Easy to find  
h
Easy to understand  
Well organized  
Applicable to your tasks  
h
h
h
Please tell us how we can improve this book:  
Thank you for your responses. May we contact you?  
h Yes  
h No  
When you send comments to IBM, you grant IBM a nonexclusive right to use or distribute your comments in any  
way it believes appropriate without incurring any obligation to you.  
Name  
Address  
Company or Organization  
Phone No.  
Cut or Fold  
Along Line  
Readers’ Comments — We’d Like to Hear from You  
GA27-4309-01  
ꢀꢁꢂꢃ  
Fold and Tape  
Please do not staple  
Fold and Tape  
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _  
NO POSTAGE  
NECESSARY  
IF MAILED IN THE  
UNITED STATES  
BUSINESS REPLY MAIL  
FIRST-CLASS MAIL PERMIT NO. 40 ARMONK, NEW YORK  
POSTAGE WILL BE PAID BY ADDRESSEE  
IBM Corporation  
Design & Information Development  
Dept. CJMA/Bldg. 645  
PO Box 12195  
Research Triangle Park, NC 27709-9990  
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _  
Fold and Tape  
Please do not staple  
Fold and Tape  
Cut or Fold  
Along Line  
GA27-4309-01  
ꢀꢁꢂꢃ  
Part Number: 03R5994  
11-9-2005  
Printed in USA  
GA27-4309-01  

Musica CRW4260tx User Manual
Motorola MPx220 User Manual
Maxtor Basics STM305003EHD301 RK User Manual
Lindy 42791 User Manual
LG Electronics VX 9400 User Manual
HTC Touch Pro RAPH500 User Manual
HTC Touch Diamond Phone User Manual
HP Hewlett Packard SURE STORE DAT DAT40I User Manual
Grindmaster SHUTTLE APBVSA 430V2E230 User Manual
Bloomfield 2074FR User Manual