IBM 09N4076 User Manual



4X/8X/32X CD-ReWritable drive'

4X/8X/32X Internal

RW CD-ROM Drive

Option Kit

User's Guide

OP TIONS

by IBM

Note: Before using this information and the product it supports, be sure to read

the information under Appendix E, “Product warranty and notices” on page 2-22.

First Edition (February 2000)

The following paragraph does not apply to the United Kingdom or any country where such

provisions are inconsistent with local law: INTERNATIONAL BUSINESS MACHINES

CORPORATION PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF

ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR

PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain

transactions, therefore, this statement may not apply to you.

This publication could include technical inaccuracies or typographical errors. Changes are

periodically made to the information herein; these changes will be incorporated in new editions of

the publication. IBM may make improvements and/or changes in the product(s) and/or the

program(s) described in this publication at any time.

It is possible that this publication may contain reference to, or information about, IBM products

(machines and programs), programming, or services that are not announced in your country.

Such references or information must not be construed to mean that IBM intends to announce such

IBM products, programming, or services in your country.

Requests for technical information about IBM products should be made to your IBM reseller or

IBM marketing representative.

Note to U.S. Government Users — Documentation related to restricted rights — Use, duplication

or disclosure is subject to restrictions set forth in GSA ADP Schedule Contract with IBM Corp.

Contents

Safety: Read first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Registering your option

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

About this book

Part 1: Installation and usage guide . . . . . . . . . . . . . . . . 1-1

Part 2: Appendixes . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

Appendix A. Product specifications . . . . . . . . . . . . . . . . . . . . . 2-1

Appendix B. Problem solving . . . . . . . . . . . . . . . . . . . . . . . . 2-5

Appendix C. Customizing device driver configuration settings . . . . . . . 2-13

Appendix D. Help and service information . . . . . . . . . . . . . . . . . 2-20

Online technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Telephone technical support . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20

Appendix E. Product warranty and notices . . . . . . . . . . . . . . . . . 2-22

Warranty statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22

Notices

Trademarks

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33

Electronic emission notices

. . . . . . . . . . . . . . . . . . . . . . . . . . 2-34

 Copyright IBM Corp. 2000

iii

Safety: Read first

Before installing this product, read the Safety Information.

Antes de instalar este produto, leia as Informações de Segurança.

Před instalací tohoto produktu si přečtěte příručku bezpečnostních instrukcí.

Læs sikkerhedsforskrifterne, før du installerer dette produkt.

Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.

Avant d'installer ce produit, lisez les consignes de sécurité.

Vor der Installation dieses Produkts die Sicherheitshinweise lesen.

Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza

Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.

Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.

Antes de instalar este produto, leia as Informações sobre Segurança.

Pred inštaláciou tohto zariadenia si pečítaje Bezpečnostné predpisy.

Antes de instalar este producto lea la información de seguridad.

iv IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit

Läs säkerhetsinformationen innan du installerar den här produkten.

Registering your option



Thank you for purchasing OPTIONS by IBM . Please take a few moments to register

your product and provide us with information that will help IBM to better serve you in

the future. Your feedback is valuable to us in developing products and services that

are important to you, as well as in developing better ways to communicate with you.

http://www.ibm.com/pc/register

IBM will send you information and updates on your registered product unless you

indicate on the Web site questionnaire that you do not want to receive further

information.

About this book

This manual contains information on the IBM 4X/8X/32X CD-ReWritable Internal

IDE Option Kit. It is divided into the following parts:

Part 1:

Installation and usage instructions in the following languages:

English

German

French

Italian

Spanish

Brazilian Portuguese

Japanese

Part 2:

Device driver special configuration settings, problem solving, help and

service information, warranty, and notices

Note: The illustrations in this manual might be slightly different from your hardware.

vi IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit

Part 1: Installation and usage guide

This part of the manual consists of an introduction, installation instructions, and

instructions for using and maintaining the CD-RW drive.

Introduction

This section will give you a description of this option and the software which comes

with it, as well as some information you will need before you install the option.

Product description

The IBM can write and read CD-RW (CD-ReWritable) and CD-R (CD-Recordable)

discs, and can read mass-produced stamped CDs. As a result, CDs created by this

drive are compatible with MR (Multi-Read) CD-ROM and DVD-ROM drives that can

read CD-RW discs and other media types, and with older non-MR CD-ROM drives

that can read only CD-R and CD-ROM discs.

The drive writes to CD-RW and CD-R discs at different speeds. The drive can write

to a CD-RW disc at up to four times the standard CD-ROM speed, recording data at

up to 1200 KB¹per second. At this rate, the drive can record approximately 650 MB²

of information on a CD-RW disc in about 18 minutes. The drive can write to a CD-R

disc at up to eight times the standard CD-ROM speed, recording data at up to 2400

KB per second. At this rate, the drive can record approximately 650 MB of

information on a CD-R disc in about nine minutes. The drive can also read data at up

to 32 times the standard CD-ROM speed, or 9600 KB per second.

Note: To use the drive’s CD-recording function, you must install the Easy CD



Creator/DirectCD software (included) for Microsoft Windows 98, Windows



95, or Windows NT 4.0. For more information on the Easy CD

Creator/DirectCD software, see “Software description” on page 1-2.

The IBM can be installed only in a computer that uses the integrated drive electronics

(IDE) or the enhanced IDE architecture.

In addition to this book, the option kit includes:

CD-RW drive

Two audio cables

Four mounting screws (M3 x 5 mm, slotted)

IDE cable

Two faceplates³for use with certain systems

KB equals approximately 1024 bytes when referring to data transfer speeds.

MB equals approximately 1000000 bytes when referring to storage capacity.

If you purchased the black option kit, you will receive one black faceplate.

 Copyright IBM Corp. 2000

1-1

Blank CD-RW disc

Blank CD-R disc

Adaptec Easy CD Creator/DirectCD disc

IBM Option Diskette

Laser Safety Guide for CD-ROMs

Electrical safety booklet

Contact your place of purchase if an item is missing or damaged. Be sure to retain

your proof of purchase. It might be required to receive warranty service. See

Appendix D, “Help and service information” on page 2-20 for technical support

information.

Software description

The Adaptec Easy CD Creator/DirectCD CD contains programs that work with

Windows 98, Windows 95, Windows 2000, and Windows NT Workstation 4.0. You

can use the programs with your CD-RW drive to create audio and data CDs, to copy

CDs, and to make jewel case inserts or CD labels. This manual will give you basic

instructions on using the software so that you can get started creating CDs. Additional

information about the software and how to use it can be found in the online user’s

guide on the software disc.

The IBM Option Diskette contains device drivers for Windows 98, Windows 95,



Windows NT 4.0, Windows 3.x, OS/2 , and DOS that enable you to access the drive

as a CD-ROM drive in DOS mode. The diskette also includes an audio CD-player

program for DOS and a diagnostic program.

Note: The software included in this option kit does not enable the drive’s

CD-recording capabilities with DOS, Windows 3.x, or OS/2 operating systems.

Before you begin

Read the following information before you start your installation.

You must complete the following steps to install the drive:

1. Determine which IDE port to use and the corresponding configuration setting.

2. Place or change the configuration jumper on the drive (and possibly make

changes to the configuration jumpers of other devices).

3. Install the drive in a drive bay.

4. Configure the system.

5. Install a device driver.

If you do not understand these procedures or are unsure about your ability to perform

all the procedures described, have a qualified computer technician install the CD-RW

drive for you.

1-2 IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit

System requirements

Before you begin installing the drive, be sure your computer meets the following

system requirements.



Minimum microprocessor: Intel Pentium processor (or the equivalent)

Minimum RAM: 16 MB⁴

3.5-inch diskette drive

Available IDE connection

Available internal power connection

Available drive bay

One of the following operating systems:

–

Microsoft Windows NT Workstation 4.0

Microsoft Windows 95 or Windows 98

Microsoft Windows 2000

You may need a flathead or phillips screwdriver to complete the installation. You

may also need to refer to the documentation that comes with your computer. Be sure

to have the documentation available.

Handling instructions

To protect your CD-RW drive during installation, observe the following precautions:

Handle the drive with care. Dropping or jarring the drive can damage the

components inside the drive housing.

Keep the CD-RW drive in its antistatic bag until you are ready to install the drive

in your computer. Limit your movement. Movement can cause static electricity

buildup.

Do not force insertion of the power cable. Doing so might damage the connector

or the drive.

When referring to memory storage capacity, MB means approximately 1 000 000 bytes; total

user-accessible capacity may vary depending on operating environment.

Part 1: Installation and usage guide 1-3

Front view of the drive

Refer to the illustration to identify parts that might be referred to in the installation

instructions.

.1/ Headphone jack

This jack provides audio output to the headphones.

.2/ Volume control

This dial controls the headphone volume.

.3/ CD tray

This tray is where you load and unload a CD.

.4/ Busy indicator

This light comes on when the drive reads from, writes to, or plays a CD.

.5/ Manual-eject hole

This hole provides access to the eject mechanism to remove a CD from the drive.

.6/ Eject/Load button

This button opens and closes the CD tray when you push it.

Back view of the drive

Refer to the illustration to identify parts that might be referred to in the installation

instructions.

.1/ Reserved

.2/ Audio-out connector

This port connects the CD-RW drive to a sound adapter.

1-4 IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit

.3/ Configuration pins

These pins are used to set the drive configuration.

.4/ IDE connector

This port connects the CD-RW drive to the IDE cable.

.5/ DC-power connector

This port connects the CD-RW drive to the computer power supply cord.

Installing the drive

Follow these steps to install the CD-RW drive into your computer.

Step 1. Opening the computer

1. Turn off the computer and all attached devices.

2. Unplug the power cords for the computer and all attached devices.

3. Remove the cover from the computer.

Step 2. Unpacking the drive

1. Before opening the antistatic bag that the drive is packed in, touch it to an

unpainted metal surface for at least two seconds. This drains the static electricity

from the package and your body.

2. Remove the drive from the bag.

If you must put the drive down, place the antistatic bag on a flat padded surface,

such as a magazine, and place the drive on the antistatic bag.

Step 3. Selecting an IDE port

Newer computers typically have two IDE ports, each of which can support two

devices. Typically, the IDE port connected to your hard disk drive is the primary IDE

port. The other IDE port is the secondary port. The IDE port and the cable position

that you select determine which configuration jumper setting you use for the drive.

If you have two IDE ports, connect the CD-RW drive to the secondary IDE port

on your system board or IDE adapter. If the CD-RW drive is the only device on

the secondary IDE port, use the master configuration setting. If the CD-RW drive

is the second device on the secondary port, use the subordinate (or slave)

configuration setting.

If you must attach the CD-RW drive to the primary IDE port (the same port as a

hard disk drive or other fast device), use the subordinate setting for the CD-RW

drive and the master setting for the faster device. In some instances, you might

need to change the hard disk drive configuration setting to

master-with-subordinate-present when attaching a subordinate device on the same

cable. For further information on setting configuration jumpers on other devices,

Part 1: Installation and usage guide 1-5

refer to the documentation that comes with your computer or with the device in

question.

Some non-IBM computers support the cable-select setting, where the position of

the device on the cable determines whether a device is master or subordinate.

See the documentation that comes with your computer to determine if your

computer supports this setting.

Step 4. Setting the configuration jumper

The illustration shows the master .1/ setting, the subordinate (or slave) .2/ setting,

and the cable-select .3/ setting. Configure the CD-RW drive by placing the jumper

over the set of pins corresponding to the setting you chose in “Step 3. Selecting an

IDE port.”

If you are configuring the CD-RW drive as master, set the jumper to the master

.1/ device setting. (This is how the drive is set when it is shipped.) If there is a

second device on the IDE port, make sure that device is configured as

subordinate.

If you are configuring the CD-RW drive as subordinate, set the jumper to the

subordinate .2/ device setting. Make sure that the other device on the IDE port

is configured as master (or master-with-subordinate-present).

If you are configuring the CD-RW drive as cable-select, set the jumper to the

cable-select .3/ device setting. If there is another device on the IDE port, make

sure that the second device is also configured for cable-select.

Step 5. Mounting the drive in the bay

Attention: Be sure to use the M3 x 5 mm mounting screws in the option

package. Using screws that are too long might damage the drive.

You can mount the CD-RW drive horizontally or vertically in the computer. If you

mount the drive vertically, you must secure any CDs you place into the drive before

the drive tray is closed, or the CD-RW drive will not be able to read the CD properly.

For further instructions on securing your CDs in a vertically mounted drive, go to page

1-12.

1-6 IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit

1. Slide the drive into the bay. Your computer might have specific required

procedures for installing storage devices. Refer to the documentation that comes

with your computer for further instructions.

2. Align the drive-bay screw holes with the threaded holes in the drive housing or

mounting bracket; then thread the screws in loosely to check their positions.

Usually two screws are used on each side.

3. Check to make sure the alignment is correct; then tighten the screws to secure the

drive. Do not overtighten.

Step 6. Attaching the cables to the drive

Connect the cables to the CD-RW drive as follows.

1. If you want to connect the CD-RW drive to your sound adapter or to the sound

function on your system board, locate the included audio cables and determine

which cable best fits the CD audio-in port on your sound adapter. Connect one

end of the selected audio cable to the CD-RW drive audio-out connector .1/, and

the other end of the cable to your sound adapter CD audio-in port. Save the other

cable in case you use a different sound adapter in the future.

2. Attach a 40-pin IDE-cable connector .2/ to the IDE connector on the drive.

Align the cable so that the color-coded edge is closest to the power cable

connector .3/. Use the IDE cable provided with this option if there is no cable

attached to the IDE port or if there is only one device connector on the IDE

cable. If you use the included IDE cable, attach one end of the cable to your

system board IDE port or to your IDE adapter, and the other end of the IDE cable

to the CD-RW drive.

3. Locate one of the available power cords attached to your computer power source.

Attach the four-pin power cable .3/ to the CD-RW drive dc power connector.

Part 1: Installation and usage guide 1-7

Step 7. Completing the hardware installation

1. Be sure that the drive is securely mounted and the connectors are firmly attached.

2. Be sure that the cables do not interfere with the computer cover and do not block

the power-supply fan blades or air-flow paths.

3. Reinstall the computer cover.

4. Reconnect all devices and check any devices that might have become

disconnected, such as the keyboard, mouse, and monitor.

5. Plug all power cords into electrical outlets.

Step 8. Attaching the faceplates

This option package includes two faceplates that conform to the curved design of

certain computers. If your computer has a curved design, you can attach one of the

included faceplates so that the front of the CD-RW drive matches the exterior cabinet.

Choose the faceplate that best fits your computer, and attach it after you have mounted

the CD-RW drive in the appropriate bay.

Note: Depending on the exterior design of your computer, you may need to attach

the faceplate before placing the cover back on your computer.

Step 9. Updating your computer configuration

After you have completed the hardware installation, restart your computer. Usually,

the configuration-setup information screen is displayed. If this screen is not displayed,

check your computer documentation for information about accessing the configuration

or setup utility program.

To see the configuration information for most IBM computers, press F1 during startup.

When you have finished reviewing the information, save the changes and exit.

Note: Some older computers with one IDE port might not display the CD-RW

drive information when you review the configuration-setup information. You still

can use the CD-RW drive in this situation if you have properly completed the

installation.

Step 10. Installing the (optional) DOS device driver

Note: This device driver is not necessary to use the CD-RW drive with most

operating systems. It is only necessary if you plan to use the CD-RW drive as a

CD-ROM drive with DOS, or you need to access the CD-RW drive using a DOS

prompt. Be sure to see the READ.ME file on the Option Diskette for the latest

information about the software on the Option Diskette.

The IBM Option Diskette contains device drivers that allow you to access the CD-RW

drive from a DOS prompt.

1-8 IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit

To install the IBM Option Diskette device drivers for Windows 98, Windows 95,

Windows 3.x, OS/2 or DOS:

1. Insert the IBM Option Diskette into the diskette drive.

2. Type A:CDSETUP in a command line and press Enter.

3. Click Setup.

4. Follow the on-screen instructions to install the software.

5. Click Exit after software installation completes.

6. Restart your computer so the new settings take effect.

Windows NT 4.0 will automatically detect the presence of the drive. No additional

steps are required to activate the device drivers.

For optional information about configuring the IBM Option Diskette device drivers for

Windows 3.x, DOS, OS/2, Windows 98, and Windows 95, go to Appendix C,

“Customizing device driver configuration settings” on page 2-13.

Step 11. Installing the Easy CD Creator/DirectCD software

Note: Be sure to see the README file for the latest information about the Easy

CD Creator/DirectCD software.

The Easy CD Creator/DirectCD CD contains the following programs:

Easy CD Creator

DirectCD

UDF Reader

To fully use the capabilities of your CD-RW drive, you need to install both the Easy

CD Creator and DirectCD programs. If you also have a MR (multi-read) CD-ROM or

DVD-ROM drive in your computer, you might need to install the UDF Reader

program to read certain CD-R or CD-RW discs in these drives.

To install the Easy CD Creator/DirectCD software for Windows 98, Windows 95,

Windows 2000 or Windows NT 4.0:

1. Insert the Easy CD Creator/DirectCD CD into your CD-RW drive.

2. If the Adaptec Easy CD Creator Installation window opens, follow the onscreen

instructions. If not, continue to the next step.

3. Click Start --> Settings --> Control Panel.

4. Double-click Add/Remove Programs.

5. Follow the on-screen instructions to complete the installation. Repeat as

necessary to install each of the Easy CD Creator, DirectCD, and UDF Reader

components.

6. Restart your operating system.

Part 1: Installation and usage guide 1-9

Using CD-R and CD-RW discs

The CD-RW drive can write to both CD-R and CD-RW discs. CD-R discs cannot be

erased, but can be used with standard CD-ROM drives and CD players. You can use

CD-R discs to record audio tracks, store data, archive files, and copy files from

another CD.

CD-RW discs can be erased and rewritten, but can be used only with newer MR

(multi-read) and CD-RW compatible CD-ROM and DVD-ROM drives. You can use

CD-RW discs to back up, store, and update files, or to copy files from another CD.

Note: CD-R discs are playable on audio CD players. CD-RW discs are not playable

on most audio CD players.

Using the drive

This section will give you information on how to handle and care for CDs and your

CD-RW drive, how to load CDs into your CD-RW drive, and how to get started using

the Easy CD Creator and DirectCD programs.

Handling and caring for a CD

CDs are high-density media that must be handled with care and kept clean to insure

that they remain readable. These precautions will help to prolong the life of your

CDs.

Attention: Wiping a CD using a circular motion might cause loss of data.

Handle the CD by the edges or by the center hole. Do not touch the surface of

the CD.

To remove dust or fingerprints, wipe the CD from the center to the edge with a

soft, lint-free cloth.

1-10 IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit

Do not write on the surface.

Do not place the CD in direct sunlight.

Do not use commercial cleaners to clean the CD.

Do not bend the CD.

Caring for the CD-RW drive

To protect your CD-RW drive during operation, observe the following precautions.

Remove any CD in the drive before moving the drive.

Do not insert foreign objects into the drive.

Do not stack objects on the drive.

Do not remove the drive cover or attempt to service the drive.

Do not operate the drive under any of the following conditions:

–

High temperature, high humidity, or direct sunlight

Excessive vibration, sudden shock, or inclined surface

Excessive dust

Loading a CD

To load a CD into a horizontally mounted CD-RW drive, follow these steps.

1. Press the Eject/Load button. The tray slides out of the drive.

2. Insert the CD into the loading tray with the label facing up.

3. Close the loading tray by pressing the Eject/Load button, or by gently pushing the

tray in.

Attention: Do not force the tray to open; do not insert foreign objects into the

CD tray. If your tray does not open when you press the Eject/Load button, see

“Manually ejecting a CD” on page 1-13 for information on manual ejection.

Part 1: Installation and usage guide 1-11

To load a CD into a vertically mounted CD-RW drive, follow these steps.

1. Press the Eject/Load button.

2. Look at the illustrations and compare them to your loading tray.

If your loading tray looks like the left illustration, insert the CD carefully so

that the edges of the CD are underneath the tabs on the loading tray. These

plastic tabs cover the edges of the CD and hold it in place. The tabs are

attached to the tray itself and cannot be moved.

If your loading tray looks like the right illustration, insert the CD into the

tray, and gently push the movable tab forward to hold the CD in place.

3. Close the loading tray by pressing the Eject/Load button, or by gently pushing the

tray in.

1-12 IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit

Manually ejecting a CD

If you press the Eject/Load button and the tray does not slide out, turn off the

computer and straighten a large paper clip to form a tool, as shown in the illustration.

The straightened end must extend at least 45 mm (1.8 in.). Insert the extended end

into the manual-eject hole on the front of the drive (see “Front view of the drive” on

page 1-4). Push the paper clip into the hole until the tray opens. Gently pull out the

tray until you can remove the CD.

45 mm

1.8 in

Using the Easy CD Creator/DirectCD programs

To use the Easy CD Creator/DirectCD software, insert a blank or partially-recorded

CD-R or CD-RW disc (this option kit includes a blank CD-R disc and a blank CD-RW

disc) into your CD-RW drive. The Easy CD Creator menu window opens

automatically.

To open DirectCD:

1. Click Start --> Programs --> Adaptec DirectCD.

2. Click DirectCD Wizard.

Formatting CDs

You must format a blank CD-RW disc using DirectCD before you can copy files to

the disc.

To format a CD-RW disc⁵with the DirectCD program:

1. Insert a blank disc (included) in the drive. The DirectCD Wizard Welcome

window opens.

2. Click Next twice. The Format Disc window opens.

Attention: Formatting completes in about 30 minutes. The DirectCD program

configures the disc to receive data, verifies the integrity of the disc surface, and

writes DirectCD file system structures to the disc. You can do other tasks on your

computer while the disc is being formatted.

3. Click Next to continue. The Name Your Disc window opens.

Some CDs, such as multisession CDs, do not require formatting. For more information, see the

Adaptec software online user’s guide.

Part 1: Installation and usage guide 1-13

4. Type the title of your disc in the Name Your Disc window. The disc name can

be up to 11 characters.

5. If you plan to use data compression software with this disc, click to check the

box next to the message Enable compression on this disc.

6. Click Finish in order to start disc formatting. When the disc is finished

formatting, the Disc Ready window opens.

7. Click OK in the Disc Ready window.

You can now write information to the disc.

Note: If you have a problem formatting a CD-RW disc, go to Appendix B, “Problem

solving” on page 2-5.

If you want to read a DirectCD-formatted disc in another computer that has a MR

(multi-read) drive, you might have to install the UDF Reader program on the other

computer.

Creating data CDs

To create data CDs:

1. Click Start --> Programs --> Adaptec Easy CD Creator --> Create CD.

2. When the Easy CD Creator window opens, click Data.

3. Click Data CD.

Note: If you click DirectCD instead of Data CD the Easy CD Creator program

will close and the DirectCD Wizard will open instead.

4. The window that opens is similar to the Windows Explorer. In the top section,

click to select the files or directories you want to add to the CD.

5. Click the Add button at the top of the window to add the files to your CD.

For information on advanced features such as making a multisession CD, or creating a

CD using the File menu instead of the Easy CD Creator Wizard, see the Adaptec

software online user’s guide.

Creating audio CDs

To create audio CDs:

1. Click Start --> Programs --> Adaptec Easy CD Creator --> Create CD.

2. When the Easy CD Creator window opens, click Audio.

3. Click Audio CD.

4. The window that opens is similar to the Windows Explorer. In the top section,

click to select the audio files or audio tracks you want to add to the CD.

5. Click the Add button at the top of the window to add the files to your CD.

For information on advanced features such as making a multisession CD, or creating a

CD using the File menu instead of the Easy CD Creator Wizard, see the Adaptec

software online user’s guide.

1-14 IBM 4X/8X/32X CD-ReWritable Internal IDE Option Kit

Making a jewel case insert

You can use Easy CD Creator to create a jewel case insert or CD label. When you

create a data or audio CD, the Easy CD Creator program creates a jewel case insert

using the information in your CD layout, such as CD title, artist name, and song list.

To print a jewel case insert or CD label:

1. Click Start --> Programs --> Adaptec Easy CD Creator --> Create CD.

2. Click Jewel Case Creator.

3. On the left, click to select the front cover, inside front cover, back cover, or CD

label.

4. Make any changes in the main editing window. You can change the background

theme by clicking the Format menu and selecting Change Themes.

5. When you are finished making changes, click the File menu and select Print;

then click OK.

For more information on changing the information in the Jewel Case Layout window,

see the Adaptec software online user’s guide.

Backing up a CD

Attention: The CD Copier program copies files from one CD to another CD. To

copy a commercial CD, you must either own the copyright or obtain permission

from the copyright owner. If you do not own the copyright or do not have

permission to copy from the copyright owner, you might be violating copyright

law and might be subject to payment of damages or other remedies. For more

information on copyright law, consult your legal advisor.

To back up (copy) a CD using your CD-RW drive:

1. Click Start --> Programs --> Adaptec Easy CD Creator --> Features.

2. Click CD Copier.

The CD Copier window will open.

3. Click the Source and Destination tab if it is not on top.

4. In the Copy From section, select the source drive from the scrolldown box.

Note: This is the drive containing the CD you want to copy.

5. In the Record To section, select the CD-RW drive from the scrolldown box. Be

sure that there is a blank CD-R or CD-RW disc in the CD-RW drive.

6. On the Advanced tab, you can choose to test the CD for the best possible

recording speed. You can also change the number of copies made, or choose to

have the CD copied to your hard disk before copying it to the blank CD. These

selections will increase the time it takes to copy the CD.

7. When you are finished choosing the settings, place the CD you are going to copy

into the source drive.

8. Click Copy to start copying your CD.

Part 1: Installation and usage guide 1-15

Installation and usage guide (Translate)