•
•
•
•
Press UP (+) or DOWN (-) adjusting the current month and then
press MODE to confirm – the date digit will flash
Press UP (+) or DOWN (-) adjusting the date and then press
MODE to confirm – the hour digit will flash in the Time Window
Press UP (+) or DOWN (-) adjusting the hour and then press
MODE to confirm – the minutes will flash
Press UP (+) or DOWN (-) adjusting the minutes and then press
MODE to confirm – the temperature unit (C or F) in the
Temperature and Alarm Window will flash
Press UP (+) or DOWN (-) button once selecting the temperature
unit in Fahrenheit or Celsius
Press MODE for the last time to confirm after the last parameter
is set
Once the time signal has been successfully received, the time and the
date will be updated automatically.
TABLE OF CONTENTS
INTRODUCTION
3
3
6
7
8
TEMPERATURE AND ALARM WINDOW
The Temperature and Alarm Window displays an indoor temperature
and the time alarms.
PRODUCT OVERVIEW
BEFORE YOU BEGIN
BATTERY INSTALLATION
ATOMIC CLOCK
Honeywell
TIME AND CALENDAR WINDOWS
The Atomic Projection Clock displays time in an hour-minutes-seconds
format in the Time Window located below the Temperature and Alarm
Window.
The date is displayed in month-date format next to the day of the week
and moon phase icon in the Calendar Window.
Atomic Projection Clock
•
•
TEMPERATURE AND ALARM WINDOW
TIME AND CALENDAR WINDOWS
MANUAL SETTINGS
ALARMS
9
9
9
DAY OF THE WEEK LANGUAGE
•
10
11
11
12
12
13
13
14
Press and hold DOWN (-) button for 3 seconds to enter into the
day of the week language programming mode: the default
language abbreviation will appear (example – EN)
Continue holding DOWN (-) button until the desired day of the
week language abbreviation is displayed
Release the DOWN (-) button and the day of the week will be
displayed in selected language
MANUAL SETTINGS
If desired, the time, date and other available parameters can be
programmed manually.
It is necessary to set your Time Zone manually.
TIME ZONE
SNOOZE
PROJECTION
•
•
BACKLIGHT
PRECAUTIONS
•
Enter the US Time Zone programming mode by pressing and
TROUBLESHOOTING
SPECIFICATIONS
holding the UP (+) button for 3 seconds.
ALARMS
The Atomic Projection Clock has two time alarms. If any of the alarms is
activated, it will sound at the set time and the alarm icon will flash
•
Keep holding UP (+) button until the desired time zone (Pacific,
Mountain, Central or Eastern) is highlighted on the unit’s display
map in the Time Window
STANDARD WARRANTY INFORMATION
PROGRAMMING THE TIMES OF THE ALARMS
•
•
Release the UP (+) button and the desired Time Zone will be
selected
Press MODE button to view the ALARM 1 or ALARM 2 modes.
If the ALARM 1 is selected, the default time “6:00” with the
ALARM 1 label will be displayed. If the ALARM 2 is selected, the
default time”8:00”with the ALARM 1 label will be displayed
CLOCK
•
Press and hold MODE button for 3 seconds until the year digits
in the Calendar Window will flash
•
Press and hold
will flash
button for three seconds - the hour digit
(PCR191W)
•
•
•
Enter the hour using DOWN (-) or UP (+) buttons
•
•
Press UP (+) or DOWN (-) adjusting to correct year
Press MODE to confirm and move to the next parameter – the
month digit will flash
USER MANUAL
Press
button once - the minute digits will flash
Enter minutes using DOWN (-) or UP (+) buttons
3&5ꢀꢁꢀ:ꢂ+21(<:(//ꢃ0$18$/ꢂꢄ(1*ꢅ
6,=(ꢆ:ꢇꢈꢂ;ꢂ+ꢀꢉꢈꢂꢄ00ꢅ
%<ꢂ;ꢂ+ꢂ+8$1*ꢂꢊꢀꢋꢉꢈꢋꢉꢁ
•
FRONT VIEW
•
•
•
•
Press
button once again. The minute digits for snooze
Press and hold FLIP button for 2 seconds again and the
projected image will rotate between the time and indoor
temperature information every 5 seconds
INTRODUCTION
interval will flash
Thank you for selecting the Honeywell Atomic Projection Clock. This
device delivers a precise time keeping with projecting the time and
temperature onto the wall or the ceiling.
A
B
C
Enter the desired interval in minutes (from 1 to 59) using DOWN
(-) or UP (+) buttons
Press
button once confirming the ALARM 1 time is set.
CONTINUOUS TIME AND TEMPERATURE PROJECTION
Connect AC/DC adapter provided to the adapter input to project the time
and/or temperature image continuously.
I
Use the same procedure for setting the time for ALARM 2
D
In this package you will find:
E
H
•
•
•
One Atomic Projection Clock
One AC adapter
ACTIVATING OR DEACTIVATING THE ALARMS
•
F
G
At any time press
or
to activate or deactivate
applicable alarm
One User Manual
•
When ALARM 1 and ALARM 2 are disabled, an applicable icon
Please keep this manual handy as you use your new item. It contains
practical step-by-step instructions, as well as technical specifications and
precautions you should know.
or
disappears from the unit’s display.
REAR VIEW
SNOOZE
When any alarm sounds, press the SNOOZE/LIGHT button to temporarily
stop the alarm. After the SNOOZE/LIGHT button are depressed, the
alarm sound will resume in the programmed snooze period.
If the alarm is not disabled after that, it will sound for four more minutes
and then will stop by itself.
PRODUCT OVERVIEW
FEATURES
J
•
Precise time and date set via RF signals from the US Atomic
Clock
K
K
PROJECTION
•
Calendar displaying date with month and day in English, Spanish
or French
The Atomic Projection Clock is capable of projecting the information for a
limited time, as well as continuously.For projection of the image on the
wall or ceiling, rotate the rear body swivel compartment clockwise or
counterclockwise.
BACKLIGHT
L
the backlight feature is activated in blue color for 3 seconds when the
LIGHT/SNOOZE button is pressed.
•
•
•
•
•
•
•
•
•
•
12 or 24 hour time format
Dual crescendo time alarm with programmable snooze
Moon phase calendar
M
LIMITED TIME PROJECTION
•
PRECAUTIONS
Press SNOOZE/LIGHT button once to project the current time
image in red color for three seconds.
This product is engineered to give you years of satisfactory service if
handled carefully. Here are a few precautions:
Indoor temperature
SIDE/TOP VIEW
Temperature unit selection in Fahrenheit or Celsius
Projects time or temperature on ceiling or wall
Focus adjustment
Control image with 180° rotation or flip
LED backlight
•
•
Do not immerse the unit in water.
Do not clean the unit with abrasive or corrosive materials. They
may scratch the plastic parts and corrode the electronic circuits.
Do not subject the product to excessive force, shock, dust,
temperature, or humidity, which may result in malfunctions,
shorter lifespan, damaged batteries, and damaged parts.
Do not tamper with the unit’s internal components. Doing so will
invalidate the warranty and may cause damage. The unit
contains no user-serviceable parts.
N
O
P
•
•
Press FLIP button to rotate projected image 180° clockwise
Q
AC/DC adapter included for continuous projection
•
FRONT VIEW
•
•
Use only fresh batteries. Do not mix new and old batteries.
Read the user's manual thoroughly before operating the unit.
Projection color: Red
I. SET
button
Backlight color: Blue
A. TEMPERATURE AND ALARM WINDOW
Displays indoor temperature and alarms
B. TIME WINDOW
Displays time with seconds and US map
C. CALENDAR WINDOW
Displays month, date, day of the week abbreviation, year and moon
phase
D. UP (+) button
•
•
Allows programming ALARM 2 and its snooze interval
Power
Activates or deactivates ALARM 2
AC/DC adapter - 3V, 120mA (included)
TROUBLESHOOTING
Check here before contacting customer service.
Dimensions
4.02(L) x 4.02(H) x 2.44(D) inches
REAR VIEW
Issue
Symptom
US Atomic Time
signal is not
Solution
J. ROTATE knob
STANDARD WARRANTY INFORMATION
Clock
Clock
Place unit by the window and
keep it there at least
overnight
This product is warranted from manufact uring defects for one year from the date of retail
purchase. It does not cover damages or wear resulting from accident, misuse, abuse,
commercial use, orunauthorized adjustment and repair.
Allows rotating of the projected image clockwise or counterclockwise
K. BATTERY COMPARTMENTS
received
Note that online product registration is required to ensure valid warranty protection.
Accommodate 2 (two) UM-3 or AA 1.5V alkaline batteries
L. FOCUS knob
Blank display
Does not project
continuously
Check/insert batteries
Connect the clock to the wall
power outlet using AC/DC
adapter provided
•
•
•
•
Increases all function parameters
To register your product, go to our Company website at:
Allows toggling between 12 and 24 hour time format
When pressed and held activates US Time Zone selection
Enforce a time signal search when DOWN (-) buttons are
pressed and held simultaneously.
a
Allows adjusting the projected image sharpness
M. 2 CLOCK FEET
Should you require assistance with this product and its operation, please contact our
Customer Service 1(866) 443 3543.
Please direct all returns to the place of the original purchase. Should this not be possible,
contact Hideki Customer Service for assistance and to obtain
Authorization (RMA). Returns without return authorization will be refused.Please retain
your original receipt as you may be asked to provide copy for proof of purchase.
Support clock ina vertical position on the flat surface
a
Return Merchandise
SPECIFICATIONS
E. DOWN (-) button
a
Time
•
•
•
Decreases all function parameters
a
Date format: month – day
SIDE/TOP VIEW
User-selectable US Time Zone
Hideki Electronics, Inc. reserves the right to repair or replace the product at our option.
Copyright (2009) Hideki Electronics Inc. All Rights Reserved. The Inc.Honeywell Trademark
is used under license from Honeywell International Inc.
Honeywell International Inc.makes no representations or warranties with respect to this
product.
Activates a language selection mode for the day of the week
Enforce a time signal search when UP (+) buttons are pressed
and held simultaneously.
N. TIME/TEMPERATURE PROJECTOR
Projects current time or indoor temperature
O. LIGHT/SNOOZE button
Day of the week: User-selectable in three languages-English, Spanish or
French
Dual 4 minutes crescendo alarm with programmable snooze
Moon phase
F. MODE button
Weather
All user manual contents and information are subject to change.
Activates LED backlight and snooze
P. REAR BODY SWIVEL COMPARTMENT
•
When pressed and held activates the clock programming mode
Indoor Temperature
•
Allows toggling between temperature and two alarm modes
Proposed operating range: -5.0°C to +50.0°C/23.0°F to 122.0°F
Temperature resolution: 0.1°C/0.1°F
User-selectable (F° or C°) temperature display
LED backlight: 3 seconds on battery power
Low battery indicator
Projection
Focus adjustment
180° projected image rotation and flip
G. FLIP button
Rotates to project time or temperature on the wall or ceiling
Q. AC ADAPTER INPUT
Allows connecting clock with the power outlet through the AC/DC adapter
provided
•
•
Flips the projected image 180° degrees
When pressed and held activates a rotation between projected
H. SET
button
BEFORE YOU BEGIN
•
•
Allows programming ALARM 1 and its snooze interval
Activates or deactivates ALARM 1
•
We recommend using alkaline batteries
•
•
Make sure the unit is positioned at 8 feet (2 meters) distance
from any interference source such as a TV, computer monitor,
microwave, etc.
Within concrete wall rooms such as basements or office buildings,
the received signal may be weakened. Always place the Atomic
Projection Clock near the window for better reception.
•
•
•
Avoid using rechargeable batteries. (Rechargeable batteries
cannot maintain correct power requirements).
Insert batteries before first use, matching the polarity in the
battery compartment
Remove protective plastic screen from LCD display (if any)
IMPORTANT NOTE: The Atomic Projection Clock does not work
without the batteries.
ATOMIC CLOCK
Immediately after installation of batteries, the clock will beep and display
all available LCD segments for a moment. Then the atomic time signal
receiver will start searching for the atomic time signal. It usually takes
between 5-8 minutes.
NOTE: Do not press any buttons on the unit during auto search as it
may interrupt product’s operation, and you will need to start the set
up procedure again
If the reception is successful and the atomic time signal is received, the
date and time will be set automatically, and the [ ] icon will appear on the
display.
NOTE: It is necessary to set your Time Zone, keeping in mind that
the default zone is a Pacific Standard Time (PST). (Refer to MANUAL
SETTINGS section)
BATTERY INSTALLATION
•
Open the battery compartment doors
Install batteries (UM-3 or “AA” size 1.5V) matching the polarity
•
2
as shown in the battery compartments
Replace the battery compartment doors
•
WWVB RADIO CONTROLLED TIME
The NIST (National Institute of Standards and Technology) radio station
(WWVB) is located in Ft. Collins, Colorado. It transmits an exact time
signal continuously throughout the most of the continental United States
at 60 KHz frequency. The Atomic Projection Clock can receive this
WWVB signal through the internal antenna from up to 2,000 miles away.
Due to the nature of the Earth’s ionosphere, reception can be limited
during the daylight hours. The radio controlled clock will search for an
alternate station that receives the atomic time signal from the NIST
If the initial reception was not successful and the time signal has not been
received in this first 8 minutes, you may press and hold the UP (+) and
DOWN (-) buttons simultaneously to enforce a signal search Or, you can
use the MODE button to set the time and date manually. (Refer to the
Atomic clock in Boulder, Colorado.
MANUAL SETTINGS section).
The WWVB tower icon on the unit’s display will flash indicating a radio
signal reception from the WWVB station. If the tower icon is not fully lit, or
if the time and date are not set automatically, please consider the
following:
After the clock is set manually, place it by the window for the better
reception. The atomic time receiver is programmed so that it will continue
to search for the atomic time signal daily for every hour between 1:00 am
and 4:30 am.
•
During night-time hours, atmospheric disturbances are typically
less severe and radio signal reception may improve. A single
daily reception is sufficient enough to keep the clock accuracy
within 1 second.
NOTE: At the time of the initial reception allow at least 24 hours for
the atomic time receiver to pick up the signal. In some cases,
depending on the location, it may take up to 72 hours.
|