CLOCK WITH
BIG DIGITAL LCD DISPLAY
94738
ASSEMBLY & OPERATING INSTRUCTIONS
Due to continuing improvement, actual product may differ slightly from the product described herein.
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Copyright© 2006 by Harbor Freight Tools®. All rights reserved. No portion of this manual or
any artwork contained herein may be reproduced in any shape or form without the
express written consent of Harbor Freight Tools.
For technical questions and replacement parts please call 1-800-444-3353.
Unpacking
When unpacking your Digital Clock, check to make sure that the product is intact and undamaged.
If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at: 1-800-444-3353.
Operation
Your Digitial Clock requires no assembly. It is important that you read the entire manual to become
familiar with the product BEFORE you use the Digital Clock.
Installing and Replacing the Battery
1.
2.
3.
Press down on the release tab on the back of the Clock to open the Battery
Compartment-see Figure 1.
Insert two “AA” batteries (not included) and line up polarity with the markings indicated in
Battery Compartment.
When the Battery is running low, the LCD readout will become light and difficult to read. This
indicates that the battery needs replacing.
Digital Clock Functions
1.
2.
Calendar:
Date can be set to any date up to 2099.
Alarm Tone: The alarm can be set for any time. The alarm tone will continously ring for
one minute.
3.
4.
5.
6.
Snooze Button:
Pre-set Alarm:
Thermometer:
Time Readout:
Snooze can be turned “On” or “Off” as desired.
The alarm can be pre-set for any time up to 30 hours ahead.
The Thermometer will give readings from -10º C/14º F to
50º C/122º F.
Time can be set to either military or standard time (12 hours or
24 hour periods).
Figure 1
Wall
Mount hole
C/F
Up
Down
Mode
Snooze
Battery
Compartment
Leg
SKU 94738
For technical questions please call 1-800-444-3353.
Page 3
Setting the Clock
1.
The mode changes each setting in the following order; hour, minute, month, day, week, alarm
hour and alarm minute. Temperature settings and snooze each have their own button-see
Figure 1.
2.
3.
Press the Mode button and the Up or Down Button to run through each of the above settings
until you arrive at the setting you desire to change or set.
Once you have arrived at the mode you desire to change or set (hour, minute, month, day,
alarm hour, alarm minute) press UP or Down button to move the setting up or down to the
desired number.
4.
5.
To activate the snooze setting, press the Snooze Button.
To change from degrees Fahrenheit to degrees Celcius, or vice-versa, press the C/F
Button.
6.
7.
The Digital Clock has folding Legs which can be pulled out to rest the Clock on a desktop-
see Figures 1 and 2. The Legs can be folded out to create a rest.
The Digital Clock can be mounted to a surface using the wall mount holes located on the
back-see Figure 1.
Figure 2
Leg
8.
Use a level to set an even line to hang the Digital Clock. Use a drill to set the path for each
screw or mounting hook (both not included). Make sure the drilling path is clear and free of
obstacles such as wires, cables and lines. Insert screws or mounting hooks into a stud.
Troubleshooting
1.
2.
LCD flashes continously: Battery charge is to low. Replace battery.
Display doesn’t change when Buttons are pushed: Circuit needs to be reset or batteries are
dead. Remove the battery, wait 30 seconds, replace battery and turn the Digital Clock “ON”.
If this does not work, replace the batteries.
3.
LCD display does not show: Batteries have poor connection or battery voltage is to low.
Take the batteries out and adjust connections. Replace the batteries as necessary.
SKU 94738
For technical questions please call 1-800-444-3353.
Page 4
Maintenance
1.
2.
3.
Protect the Digital Clock from rough use. It is susceptible to damage from being dropped,
struck, or other abuse.
Keep the Digital Clock clean and dry. Occasional cleaning with a clean rag will extend its life
and good appearance.
Keep out of the reach of children.
No replacement parts are available for this product.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A
REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT
OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/
OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY
CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 94738
For technical questions please call 1-800-444-3353.
Page 5
|