FieldServer Lutron Machine FS 8700 97 User Manual

A Sierra Monitor Company  
Driver Manual  
(Supplement to the FieldServer Instruction Manual)  
FS-8700-97 Lutron Machine  
APPLICABILITY & EFFECTIVITY  
Effective for all systems manufactured after May 1, 2001  
FS-8700-97_Lutron_Machine Manual  
Page 3 of 11  
1.  
Lutron Machine Description  
The Lutron Machine driver allows the FieldServer to transfer data to and from devices over RS-  
232 using Lutron eLumen protocol. The FieldServer can emulate either a Server or Client,  
although the Lutron Machine driver is only available in Client configuration. Any Server drivers  
are for FieldServer testing purposes only.  
Max Nodes Supported  
FieldServer Mode  
Nodes  
Comments  
Only one Lutron Machine driver Client node is able to be  
connected to a Lutron eLumen panel.  
One BACNet IP node provides an upstream interface to the  
Lutron eLumen panel.  
Client  
1
Server  
1
The Lutron Grafik Machine Zone/Area Machine driver, hereafter simply referred to as the Lutron  
Machine driver, provides a BACNet IP interface to a Lutron eLumen panel. The driver can be  
configured to represent zones or areas as used in the Lutron eLumen panel. The FieldServer  
acts as both Client and Server to provide BACNet objects to an external BACNet Client. In  
Server mode, the FieldServer collects data from the eLumen panel and holds the data ready for  
reads from an external BACNet Client. In Client mode, the FieldServer executes pre-defined  
commands on the eLumen panel, for example, running scripts.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 4 of 11  
2.  
Driver Scope of Supply  
2.1. Supplied by FieldServer Technologies for this driver  
FieldServer Technologies  
PART #  
Description  
FS-8915-10  
FS-8917-02  
FS-8700-97  
UTP cable (7 foot) for RS-232 use  
RJ45 to DB9F connector adapter  
Driver Manual.  
2.2.  
2.2.1.  
Provided by the Supplier of 3rd Party Equipment  
Hardware  
Part #  
Description  
Lutron eLumen Panel  
2.2.2.  
Required 3rd Party Software  
An external BACnet IP Client to interface to the Lutron Machine on the FieldServer.  
2.2.3.  
Required 3rd Party Configuration  
BACnet IP Client must be set up to access FieldServer over the network.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 5 of 11  
3.  
Hardware Connections  
The FieldServer is connected to the Lutron eLumen panel as shown in the connection drawing  
below:  
Configure the eLumen panel according to manufacturer’s instructions.  
FS-8917-02  
LUTRON SERIAL  
RS-232 INTERFACE  
PART # 470-784  
8917-02 WIRE LIST  
CAT 5 CABLE  
FS-8915-10  
FUNCTION  
RX  
FROM  
TO  
COLOUR  
WHITE  
BROWN  
YELLOW  
GREEN  
RED  
BLACK  
ORANGE  
BLUE  
RJ45-01  
RJ45-02  
RJ45-03  
RJ45-04  
RJ45-05  
RJ45-06  
RJ45-07  
RJ45-08  
DB9M-02  
DB9M-08  
DB9M-06  
DB9M-05  
CTS  
DSR  
GND  
GND  
DTR  
RTS  
TX  
DB9M-04  
DB9M-07  
DB9M-03  
Serial  
Power OK  
(408)-262-2299  
Tx  
EIA232  
Rx Tx  
Rx  
-
+
Ethernet  
USB  
EIA485  
LUTRON ELUMEN RS-232  
CONNECTION DIAGRAM  
FS-B2010  
BASE NAME:  
FILE NAME: FS-T28700-84 .VSD  
DATE: 11/12/04  
BY: MC  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 6 of 11  
120V 15A  
Dedicated Control  
Feed  
Wallstation link  
To control stations  
eLumen  
Processor  
Aux Link (RS-485)  
User Interface link  
Dimmer panel link  
To dimmer panels  
Inter-processor link  
Serial  
Power OK  
Tx  
EIA232  
Rx Tx  
Rx  
-
+
Ethernet  
USB  
EIA485  
FS-B2010  
(408)-262-2299  
LUTRON ELUMEN RS-485  
CONNECTION DIAGRAM  
BASE NAME:  
FILE NAME: FS-T28700-84 .VSD  
DATE: 11/12/04  
BY: MC  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 7 of 11  
4.  
Configuring the FieldServer as a Lutron Machine Client  
For a detailed discussion on FieldServer configuration, please refer to the FieldServer  
instruction manual. The information that follows describes how to expand upon the factory  
defaults provided in the configuration files included with the FieldServer (See “.csv” sample files  
provided with the FieldServer).  
This section documents and describes the parameters necessary for configuring the FieldServer  
to communicate with a Lutron eLumen panel.  
4.1.  
Data Arrays/Descriptors  
The configuration file tells the FieldServer about its interfaces, and the routing of data  
required. In order to enable the FieldServer for Lutron Machine communications, the driver  
independent FieldServer buffers need to be declared in the “Data Arrays” section, the  
destination device addresses need to be declared in the “Client Side Nodes” section, and  
the data required from the Servers needs to be mapped in the “Client Side Map Descriptors”  
section. Details on how to do this can be found below.  
Note that in the tables, * indicates an optional parameter, with the bold legal value being the  
default.  
Section Title  
Data_Arrays  
Column Title  
Function  
Legal Values  
Up to 15 alphanumeric  
characters  
Data_Array_Name  
Provide name for Data Array  
Float, Bit, UInt16, SInt16,  
Provide data format. Each Data Packed_Bit,  
Byte,  
Data_Array_Format  
Data_Array_Length  
Array can only take on one format.  
Packed_Byte,  
Swapped_Byte  
Number of Data Objects. Must be  
larger than the data storage area  
required by the Map Descriptors for  
the data being placed in this array.  
1-10,000  
Example  
// Data Arrays  
Data_Arrays  
Data_Array_Name,  
Binary_Output,  
Binary_Input,  
Analog_Output,  
Analog_Input,  
Data_Format,  
Bit,  
Bit,  
Uint16,  
Uint16,  
Data_Array_Length  
512  
512  
512  
512  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 8 of 11  
4.2.  
Client Side Connection Descriptions  
Section Title  
Connections  
Column Title  
Function  
Legal Values  
Specify which port the device  
Port  
is  
connected  
to  
the P1-P8, R1-R21  
FieldServer  
Protocol  
Baud*  
Parity*  
Data_Bits*  
Stop_Bits*  
Specify protocol used  
Specify baud rate  
Specify parity  
eLumen  
9600  
None  
8
Specify data bits  
Specify stop bits  
Specify  
1
hardware  
Handshaking*  
Poll _Delay*  
None  
handshaking  
Time between internal polls  
0-32000 seconds, 1 second  
Example  
// Client Side Connections  
Connections  
Port,  
P1,  
Protocol,  
eLumen,  
Baud,  
9600,  
Parity,  
None,  
Handshaking,  
None,  
Poll_Delay  
0.100s  
1
Not all ports shown are necessarily supported by the hardware. Consult the appropriate Instruction  
manual for details of the ports available on specific hardware.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 9 of 11  
4.3.  
Client Side Node Descriptors  
Section Title  
Nodes  
Column Title  
Node_Name  
Function  
Provide name for node  
Legal Values  
Up to 32 alphanumeric characters  
The eLumen processor address.  
Only decimal values are allowed:  
e.g. 11 hex must be entered as  
17.  
Node_ID  
0-255  
Protocol  
Specify protocol used  
eLumen  
Specify which port the device is  
connected to the FieldServer  
Specifies the eLumen command  
and data format  
P1-P8, R1-R21  
Connection  
Node_type  
Hex, decimal  
Example  
// Client Side Nodes  
Nodes  
Node_Name,  
LUT_GRF6_0,  
Node_ID,  
17,  
Protocol,  
eLumen,  
Port,  
P1,  
Node_Type  
Hex  
4.4.  
4.4.1.  
Client Side Map Descriptors  
FieldServer Related Map Descriptor Parameters  
Column Title  
Function  
Legal Values  
Name of this Map Up to 32 alphanumeric  
Map_Descriptor_Name  
Data_Array_Name  
Descriptor  
characters  
Name of Data Array  
where data is to be  
One of the Data Array  
names from “Data Array”  
section above  
stored  
in  
the  
FieldServer  
Starting location in Data 0 to maximum specified in  
Array “Data Array” section above  
Function of Client Map ARCO, AWT, RDBC,  
Descriptor Passive_Client  
Data_Array_Offset  
Function  
4.4.2.  
Driver Related Map Descriptor Parameters  
Column Title  
Function  
Legal Values  
One of the node names  
specified in “Client Node  
Descriptor” above  
Area Machine:  
Node_Name  
Name of Node to fetch data from  
run_script_AB  
Specifies the command that will be  
sent to the eLumen.  
Grafik_Command  
area_sts_offscene  
sel_scene_in_area  
run_script_multi  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Column Title  
Page 10 of 11  
Legal Values  
Function  
area_status  
sys_var_val_bin  
sys_var_val  
Zone Machine:  
run_script_AB  
zone_intensity  
fade_zone  
run_script_multi  
zone_intensity  
sys_var_val_bin  
sys_var_val  
Name of Data Array that contains a  
DA_Lut_List  
list of parameters needed to A Data Array name.  
execute the command.  
The offset into the DA_Lut_List 0 to the maximum offset  
Data Array from where the list data into the DA_Lut_List  
DA_Lut_List_Offset  
DA_Lut_Parms  
is to be used.  
Data Array.  
Name of Data Array that contains  
parameters needed to execute the A Data Array name.  
command.  
The offset into the DA_Lut_Parms 0 to the maximum offset  
DA_Lut_Parms_Offset Data Array where the driver will into the DA_Lut_Parms  
retrieve the parameters.  
Data Array.  
Area  
GRAFIK system area number  
0 – 511  
Sys_var  
Zone  
GRAFIK system variable number  
GRAFIK system zone number  
Length of Map Descriptor. The  
length is an indication of the  
number of data elements this Map  
Descriptor is responsible for  
updating. It is used in the overall  
0 – 65535  
0 – 511  
See  
example  
Map  
Descriptors for individual  
lengths  
Descriptor.  
Length  
per  
Map  
points  
calculation  
of  
the  
FieldServer.  
The length of the Data Array  
specified under DA_Lut_List when  
used with Grafik command:  
run_script_multi  
Multi_Scripts_Length  
1 – 10,000  
4.4.3.  
Timing Parameters  
Column Title  
Scan_Interval  
Function  
Rate at which data is  
Legal Values  
0.001s  
polled  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 11 of 24  
4.4.4.  
Map Descriptor Example 1 - Binary Output (Zone and Area Machine)  
A write to the Binary Output Data Array which is shared by a BACNet IP Map Descriptor will execute one of two scripts on the  
eLumen panel. The script numbers corresponding to binary inactive (0) and active (1) are specified in the Data Array specified by  
“DA_Lut_List” from offset specified by “DA_Lut_List_Offset”. Script numbers range from 0 to 65535.  
BACnet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
Data_Type, Object_ID, Length, Relinquish_Default  
SMD00_BO,  
Binary_Output,  
0,  
Server,  
Virtual_BCU_11, BO,  
1,  
512,  
0
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Run_Script_0,  
Data_Array_Name,  
Binary_Output,  
Data_Array_Offset,  
0,  
Function,  
AWT,  
Node_name,  
LUT_GRF6_0,  
Grafik_Command,  
run_script_AB,  
DA_Lut_List,  
Script_list_BO,  
DA_Lut_List_Offset,  
0,  
Length  
512  
The Data Array specified under “DA_Lut_List” must be preloaded with script numbers as shown below:  
//================================================================================  
// Binary Output Scripts Setup  
//  
// All values are in decimal (0 - 65535)  
// ScriptA in even locations, ScriptB in uneven locations, values in Preload_Data_Value  
// ScriptA will be run when writing zero into the Object ID  
// ScriptB will be run when writing non-zero into the object ID  
Preloads  
Data_Array_Name ,  
Preload_Data_Format ,  
Preload_Data_Value ,  
Location  
// Binary Output Object ID 1  
Script_list_BO ,  
Script_list_BO ,  
Uint16  
Uint16  
,
,
1
2
,
,
0
1
// Binary Output Object ID 2  
Script_list_BO ,  
Script_list_BO ,  
Uint16  
Uint16  
,
,
3
4
,
,
2
3
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 12 of 24  
4.4.5.  
Map Descriptor Example 2 - Binary Input (Zone Machine)  
A read from the Binary Input Data Array which is shared by a BACNet IP Map Descriptor will return the relay state for the given zone.  
The Lutron Machine Map Descriptor regularly polls the eLumen panel to retrieve the value of zone intensity. The value of each  
BACNet object presenting Binary Output is inactive if the intensity is zero and active if the intensity is non-zero. Zone numbers range  
from 0 to 511  
BACNet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
Data_Type, Object_ID, Length, Relinquish_Default  
SMD00_BI,  
Binary_Input,  
0,  
Server,  
Virtual_BCU_11, BI,  
1,  
512,  
0
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Zone_int_0,  
Data_Array_Name,  
Binary_Input,  
Data_Array_Offset,  
0,  
Function, Node_name,  
Grafik_Command,  
zone_intensity,  
Zone, Length  
0, 512  
ARCO,  
LUT_GRF6_0,  
The ARCO function is the same as RDBC except that the length of the Map Descriptor is taken as the number of zones to poll. The  
start zone number is specified under the “Zone” Map Descriptor field. More than one ARCO Map Descriptor may be used to poll two  
series of zone numbers, eg. from 5-10 and from 300-340. ARCO Map Descriptors with Length 1 perform the same function as  
RDBC Map Descriptors with the same length.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 13 of 24  
4.4.6.  
Map Descriptor Example 3 - Binary Input (Area Machine)  
A read from the Binary Input Data Array which is shared by a BACNet IP Map Descriptor will return the scene-on state for the given  
area. The Lutron Machine Map Descriptor regularly polls the eLumen panel to retrieve the scene-on state for the given area. The  
value returned by the BACNet object is inactive (0) if the off scene is selected and active (1) if any other scene is selected. The off  
scene numbers range from 0 to 65535 and are preloaded in the Data Array specified under “DA_Lut_List”.  
BACNet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
SMD00_BI, Binary_Input, 0, Server, Virtual_BCU_11, BI,  
Data_Type, Object_ID, Length, Relinquish_Default  
1, 512,  
0
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
Area_sts_0, Binary_Input, 0, ARCO, LUT_GRF6_0, area_sts_offscene, 0,  
Grafik_Command,  
Area, DA_Lut_List, DA_Lut_List_Offset, Length  
off_scene, 0, 512  
The ARCO function is the same as RDBC except that the Map Descriptor length is taken as the number of areas to poll. The start  
area number is specified under the “Area” Map Descriptor field. More than one ARCO Map Descriptor may be used to poll two series  
of area numbers, eg. from 5-10 and from 300-340. ARCO Map Descriptors with Length 1 perform the same function as RDBC Map  
Descriptors with the same length.  
The Data Array specified under “DA_Lut_List” must be preloaded with scene numbers as shown below:  
//================================================================================  
// Binary Input Scenes Setup  
//  
// All values are in decimal ( 0 - 65535 )  
// Insert the off-scene number in the preload_data_value field  
Preloads  
Data_Array_Name ,  
Preload_Data_Format ,  
Preload_Data_Value ,  
Location  
// Binary Input Object ID 1  
off_scene  
,
Uint16  
Uint16  
,
,
0
1
,
,
0
1
// Binary Input Object ID 2  
off_scene  
,
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 14 of 24  
4.4.7.  
Map Descriptor Example 4 - Analog Output 1 (Area Machine)  
A write to the Analog Output Data Array which is shared by a BACNet IP Map Descriptor will command an area to a preset scene on  
the Lutron eLumen panel. Scenes range from 0 to 65535 and area numbers range from 0 to 511  
BACNet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
SMD000_AO, Analog_Output, 0, Server, Virtual_BCU_11, AO,  
Data_Type, Object_ID, Length, Relinquish_Default  
1, 512,  
0
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Sel_scene_0,  
Data_Array_Name,  
Analog_Output,  
Data_Array_Offset,  
0,  
Function,  
AWT,  
Node_name,  
LUT_GRF6_0,  
Grafik_Command,  
sel_scene_in_area,  
area,  
0,  
Length  
512  
The area field must be used to indicate the start area number that will be associated with the first element of the Data Array specified  
under Data_Array_Name. Area numbers increase with the Length field in association with increasing offset into the Data Array.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 15 of 24  
4.4.8.  
Map Descriptor Example 5 - Analog Output 1 (Zone Machine)  
A write to the Analog Output Data Array which is shared by a BACNet IP Map Descriptor will command a zone on the Lutron eLumen  
panel to the written intensity. Intensities are written as a percentage value (0 to 100%).  
BACNet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
Data_Type, Object_ID, Length, Relinquish_Default  
SMD000_AO,  
Analog_Output,  
0,  
Server,  
Virtual_BCU_11, AO,  
1,  
512,  
0
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Fade_to_lvl_0,  
Data_Array_Name,  
Analog_Output,  
Data_Array_Offset,  
0,  
Function,  
AWT,  
Node_name,  
LUT_GRF6_0,  
Grafik_Command,  
fade_zone,  
zone,  
0,  
DA_Lut_Parms,  
Zone_pars_AO1,  
DA_Lut_Parms_Offset,  
0,  
Length  
512  
The zone field must be used to indicate the start zone number that will be associated with the first element of the Data Array  
specified under Data_Array_Name . Zone numbers increase with the Length field in association with increasing offset into the Data  
Array.  
Fade and Delay times per zone must be preloaded into the Data Array specified under “DA_Lut_Parms”:  
//================================================================================  
// Analog Output1 Settings Setup  
//  
// All values are in decimal ( 0 - 65535 )  
// Fade time in even locations, Delay time in uneven locations  
// Fill in time values under Preload_Data_Value  
Preloads  
Data_Array_Name ,  
Preload_Data_Format ,  
Preload_Data_Value ,  
Location  
// Analog Output1 Object ID 1  
Zone_pars_AO1 ,  
Zone_pars_AO1 ,  
Uint16  
Uint16  
,
,
0
1
,
,
0
1
// Analog Output1 Object ID 2  
Zone_pars_AO1 ,  
Zone_pars_AO1 ,  
Uint16  
Uint16  
,
,
2
3
,
,
2
3
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 16 of 24  
4.4.9.  
Map Descriptor Example 6 - Analog Output 2 (Zone and Area Machine)  
A write to the Analog Output Data Array which is shared by a BACNet IP Map Descriptor will execute one of multiple scripts on the  
Lutron eLumen panel. The value written into the Analog Output Data Array is used as an offset into the Data Array defined under  
“DA_Lut_List” to retrieve a script number. Script numbers range from 0 to 65535.  
BACNet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
Data_Type, Object_ID, Length, Relinquish_Default  
SMD512_AO,  
Analog_Output,  
512,  
Server,  
Virtual_BCU_11, AO, 513, 512,  
0
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Run_script_512,  
Data_Array_Name,  
Analog_Output,  
Data_Array_Offset,  
512,  
Function,  
AWT,  
Node_name,  
LUT_GRF6_0,  
Grafik_Command,  
run_script_multi,  
DA_Lut_List,  
Scr_lst_AO2_512,  
DA_Lut_List_Offset,  
0,  
Length,  
1,  
Multi_Scripts_Length  
10  
The Multi_Scripts_Length field is used to indicate the maximum size of the Data Array specified under Data_Array_Name. One Map  
Descriptor per object must be defined with a Multi_Scripts_Length value of 1 or greater.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 17 of 24  
The script numbers per BACNet object element need to be preloaded into the Data Arrays defined under “DA_Lut_List”.  
//====================================================================  
// Analog Output2 Settings Setup  
//  
// All values are in decimal ( 0 - 65535 )  
// Specify up to 10 scripts for each Object ID by editing Preload_Data_Value  
Preloads  
Data_Array_Name ,  
Preload_Data_Format ,  
Preload_Data_Value ,  
Location  
// Analog Output2 Object ID 513  
Scr_lst_AO2_512 ,  
Scr_lst_AO2_512 ,  
Scr_lst_AO2_512 ,  
Scr_lst_AO2_512 ,  
Scr_lst_AO2_512 ,  
Scr_lst_AO2_512 ,  
Scr_lst_AO2_512 ,  
Scr_lst_AO2_512 ,  
Scr_lst_AO2_512 ,  
Scr_lst_AO2_512 ,  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
,
,
,
,
,
,
,
,
,
,
100  
200  
300  
400  
500  
600  
700  
800  
900  
65000  
,
,
,
,
,
,
,
,
,
,
0
1
2
3
4
5
6
7
8
9
// Analog Output2 Object ID 514  
Scr_lst_AO2_513 ,  
Scr_lst_AO2_513 ,  
Scr_lst_AO2_513 ,  
Scr_lst_AO2_513 ,  
Scr_lst_AO2_513 ,  
Scr_lst_AO2_513 ,  
Scr_lst_AO2_513 ,  
Scr_lst_AO2_513 ,  
Scr_lst_AO2_513 ,  
Scr_lst_AO2_513 ,  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
,
,
,
,
,
,
,
,
,
,
101  
201  
301  
401  
501  
601  
701  
801  
901  
65001  
,
,
,
,
,
,
,
,
,
,
0
1
2
3
4
5
6
7
8
9
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 18 of 24  
4.4.10.  
Map Descriptor Example 7 - Analog Input (Area Machine)  
A read from the Analog Input Data Array which is shared by a BACNet IP Map Descriptor will return the last scene selected in a  
given area on the Lutron eLumen panel. The Lutron Machine Map Descriptor regularly polls the Lutron eLumen panel to retrieve the  
scene numbers.  
BACNet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptors_  
Name,  
SMD00_AI,  
Data_Array_  
Name,  
Analog_Input,  
Data_Array_  
Offset,  
0,  
Function,  
Server,  
Node_name,  
Data_Type,  
AI,  
Object_  
ID,  
1,  
Length,  
1,  
Relinquish_Default,  
0,  
Data_Array_  
Low_Scale,  
0,  
Data_Array_  
High_Scale,  
100,  
Node_  
Low_Scale,  
0,  
Node_  
High_Scale  
100  
Virtual_BCU_11,  
The last scene value may be scaled:  
//================================================================================  
// Analog Input Settings Setup  
//  
// All values are in decimal ( 0 - 65535 )  
// Insert a first available scene number under the Data_Array_High_Scale field for each Object ID or  
// use the scale fields as desired to scale scene numbers.  
// Object IDs are contiguous  
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Last_scene_0,  
Data_Array_Name,  
Analog_Input,  
Data_Array_Offset,  
0,  
Function,  
ARCO,  
Node_Name,  
LUT_GRF6_0,  
Grafik_Command,  
area_status,  
Area,  
0,  
Length  
512  
The ARCO function is the same as RDBC except that the length of the Map Descriptor is taken as the number of areas to poll. The  
start area number is specified under the “Area” Map Descriptor field. More than one ARCO Map Descriptors may be used to poll two  
series of area numbers, eg. from 5-10 and from 300-340. ARCO Map Descriptors with Length 1 fullfil the same function as RDBC  
Map Descriptors with the same length.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 19 of 24  
4.4.11.  
Map Descriptor Example 8 - Analog Input (Zone Machine)  
A read from the Analog Input Data Array which is shared by a BACNet IP Map Descriptor will return the intensity to which a given  
zone is set on the Lutron eLumen panel. The Lutron Machine Map Descriptor regularly polls the Lutron eLumen panel to retrieve the  
zone intensities. The intensity value returned is scaled to a percentage value (0 to 100%). Zone numbers range from 0 to 511.  
BACNet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
Data_Type, Object_ID, Length, Relinquish_Default  
SMD00_AI, Analog_Input, 0, Server, Virtual_BCU_11, AI,  
1,  
512,  
0
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Zone_inta_0,  
Data_Array_Name,  
Analog_Input,  
Data_Array_Offset,  
0,  
Function,  
ARCO,  
Node_name,  
LUT_GRF6_0,  
Grafik_Command,  
zone_intensity,  
zone,  
0,  
Length  
512  
The ARCO function is the same as RDBC except that the length of the Map Descriptor is taken as the number of zones to poll. The  
start zone number is specified under the “zone” Map Descriptor field. More than one ARCO Map Descriptors may be used to poll two  
series of zone numbers, eg. from 5-10 and from 300-340. ARCO Map Descriptors with Length 1 fullfil the same function as RDBC  
Map Descriptors with the same length.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 20 of 24  
4.4.12.  
Map Descriptor Example 9 - Multistate Output (Zone and Area Machine)  
A write to the Multistate Output Data Array which is shared by a BACNet IP Map Descriptor will execute one of multiple scripts. The  
multiple scripts are specified in the Data Array defined under “DA_Lut_List”. The value written into the Multistate Output Data Array  
is used as the offset into the Data Array defined under “DA_Lut_List” to retrieve a script number from the Data Array. Script numbers  
range from 0 to 65535.  
BACNet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
Data_Type, Object_ID, Length, Relinquish_Default,  
SMD00_MO,  
MultiSt_Output,  
0,  
Server,  
Virtual_BCU_11, MO, 1, 512, 0,  
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Run_scriptms_0,  
Data_Array_Name,  
MultiSt_Output,  
Data_Array_Offset,  
0,  
Function,  
AWT,  
Node_name,  
LUT_GRF6_0,  
Grafik_Command,  
run_script_multi,  
DA_Lut_List,  
Scr_lst_MSO_0,  
DA_Lut_List_Offset,  
0,  
Length,  
1,  
Multi_Scripts_Length  
10  
The Multi_Scripts_Length field is used to indicate the maximum size of the Data Array specified under Data_Array_Name. One Map  
Descriptor per object must be defined with a Multi_Scripts_Length value of one or greater.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 21 of 24  
The scripts per object element must be preloaded into the Data Array defined under “DA_Lut_List”:  
//=====================================================================  
// Multistate Output Scripts Setup  
//  
// All values are in decimal ( 0 - 65535 )  
// Specify up to 10 scripts for each Object ID by editing Preload_Data_Value  
Preloads  
Data_Array_Name  
Preload_Data_Format  
Preload_Data_Value  
Location  
// Multistate Output Object ID 1  
Scr_lst_MSO_0 ,  
Scr_lst_MSO_0 ,  
Scr_lst_MSO_0 ,  
Scr_lst_MSO_0 ,  
Scr_lst_MSO_0 ,  
Scr_lst_MSO_0 ,  
Scr_lst_MSO_0 ,  
Scr_lst_MSO_0 ,  
Scr_lst_MSO_0 ,  
Scr_lst_MSO_0 ,  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
,
,
,
,
,
,
,
,
,
,
110  
210  
310  
410  
510  
610  
710  
810  
910  
65010  
,
,
,
,
,
,
,
,
,
,
0
1
2
3
4
5
6
7
8
9
// Multistate Output Object ID 2  
Scr_lst_MSO_1 ,  
Scr_lst_MSO_1 ,  
Scr_lst_MSO_1 ,  
Scr_lst_MSO_1 ,  
Scr_lst_MSO_1 ,  
Scr_lst_MSO_1 ,  
Scr_lst_MSO_1 ,  
Scr_lst_MSO_1 ,  
Scr_lst_MSO_1 ,  
Scr_lst_MSO_1 ,  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
Uint16  
,
,
,
,
,
,
,
,
,
,
120  
220  
320  
420  
520  
620  
720  
820  
920  
65020  
,
,
,
,
,
,
,
,
,
,
0
1
2
3
4
5
6
7
8
9
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 22 of 24  
4.4.13.  
Map Descriptor Example 10 - Binary Value (Zone and Area Machine)  
A read from the Binary Value Data Array which is shared by a BACNet IP Map Descriptor will return the current value of a  
system variable in the Lutron eLumen panel. The value returned is inactive (0) if the system variable is zero and active (1) if  
non-zero. The Lutron Machine Map Descriptor regularly polls the Lutron panel to retrieve the system variable values. A write  
to the Binary Value Data Array will set the system variable to 255 on active (1) write or to zero on inactive (0) write.  
BACNet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
Data_Type, Object_ID, Length, Relinquish_Default  
SMD00_BV,  
Binary_Value,  
0,  
Server,  
Virtual_BCU_11, BV,  
1,  
512,  
0
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Zone_var_0,  
Data_Array_Name,  
Binary_Value,  
Data_Array_Offset,  
0,  
Function,  
ARCO,  
Node_name,  
LUT_GRF6_0,  
Grafik_Command,  
sys_var_val_bin,  
Sys_Var, Length  
0,  
512  
The ARCO function is the same as RDBC except that the length of the Map Descriptor is taken as the number of system variables to  
poll. The start system variable number is specified under the “Sys_Var” Map Descriptor field. More than one ARCO Map Descriptor  
may be used to poll two series of system variable numbers, eg. from 5-10 and from 300-340. ARCO Map Descriptors with Length 1  
fullfil the same function as RDBC Map Descriptors with the same length.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Page 23 of 24  
4.4.14.  
Map Descriptor Example 11 - Analog Value (Zone and Area Machine)  
A read from the Analog Value Data Array which is shared by a BACNet IP Map Descriptor will return the current value of a system  
variable in the Lutron eLumen panel. The variable values range from 0 to 255. The Lutron Machine Map Descriptors are regularly  
updated with system variable values from the active Binary Value Map Descriptors. A write to the Analog Value Data Array will set  
the system variable to the written value.  
BACNet IP Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, Node_name,  
Data_Type, Object_ID, Length, Relinquish_Default  
SMD00_AV, Analog_Value, 0, Server, Virtual_BCU_11, AV,  
1,  
512,  
0
Lutron Machine Map Descriptor  
// Client Side Map Descriptors  
Map_Descriptors  
Map_Descriptor_Name,  
Zone_vara_0,  
Data_Array_Name,  
Analog_Value,  
Data_Array_Offset,  
0,  
Function,  
Passive_Client, LUT_GRF6_0,  
Node_name,  
Grafik_Command,  
sys_var_val,  
Sys_Var, Length  
0,  
512  
The Passive_Client function is used to prevent double-polling the Lutron eLumen panel for system variables. The Analog Value Map  
Descriptors should be set up identical to the Binary Value Map Descriptors in terms of the Sys_Var and Length fields to ensure  
system variable values will be stored correctly.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-97_Lutron_Machine Manual  
Appendix A. Revision History  
Page 24 of 24  
Driver Doc.  
Date  
Resp Format  
Comment  
Ver.  
1.00  
1.01  
Rev.  
0
1
07/04/03 DR  
07/08/03 DR  
09/05/03 DR  
09/09/03 DR  
Created  
Updated driver version, SPR2912  
1.02  
1.02  
1
2
Updated with ARCO Map Descriptor usage  
Updated with passive Client mapdescs  
Updated according to DUR0215.  
formatting  
Updated  
10/15/03 MF  
1.02  
3
1/21/04  
3/22/04  
JD  
1.02  
1.02  
4
5
Releasing  
DR  
Updated for release  
Updated formatting. Added new revision table.  
Changed page setup to letter.  
Releasing  
Changed references to Grafik to eLumen –  
DUR0484.  
3/24/04  
6/10/04  
11/3/04  
MC  
JD  
MC  
1.02  
1.02  
1.03  
6
7
0
Meg Meg  
Connection diagrams added for RS-232 and  
RS-485. Modifications to scope of supply table.  
Table formatting. Map Descriptor example titles  
added. Added RS-485 compatibility.  
12/30/04 Meg Meg  
1.03  
1
4/12/05  
4/27/05  
JD  
JD  
JD  
JD  
1.03  
1.03  
1
2
Releasing  
Corrected page numbering. Releasing.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldserver.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  

NAD C520 User Manual
Motorola V186 User Manual
Motorola KRZR User Manual
Lindy 42937 User Manual
Kyocera K323 User Manual
Honda Automobiles Cell Phone User Manual
Compaq 6310i User Manual
Blackberry WIRELESS HANDHELDTM 857 User Manual
Audiovox ACC 52 User Manual
Aluratek ACSSDM32F User Manual