FieldServer FS 8700 70 User Manual

Driver Manual  
(Supplement to the FieldServer Instruction Manual)  
FS-8700-70 WS3000 TABS  
APPLICABILITY & EFFECTIVITY  
Effective for all systems manufactured after May 1, 2001  
Driver Version:  
1.01  
Document Revision: 6  
FS-8700-70 WS3000 Tabs Manual  
Page 3 of 14  
1.  
WS3000 TABS Description  
The Serial WS3000 TABS driver allows the FieldServer to transfer data to and from devices  
over either RS-232 or RS-422 using WS3000 TABS protocol. The FieldServer can emulate  
either a Server or Client.  
The WS3000 TABS driver is set up for Alarm Surveillance and Control. The protocol works over  
a multidrop RS-422 line or over a RS-232 line and allows only one master and up to 32 slaves  
on a serial channel. Slaves are assigned station addresses that range from 0 to 31. The master  
does not have a station address. The protocol is strictly command/response with the master  
polling the slave devices. Each slave can be configured to hold the data for one to 256  
displays. Each display contains 64 alarms status points represented by bits.  
This driver only supports short addressing mode, thus allowing for a maximum of 256 displays  
per tabs device.  
The Server driver fully supports the processing of the following AS&C Remote Control  
Commands:  
Type 0, 1, 2, 128-255  
The Client driver supports the sending of AS&C Remote Control Commands (writes).  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 4 of 14  
2.  
Driver Scope of Supply  
2.1. Supplied by FieldServer Technologies for this driver  
FieldServer Technologies  
PART #  
Description  
25029  
FS-8917-03  
FS-8700-70  
Cable Cat5 10-BASET w/Boot 7' Yelow  
Conn, DB9M to DCE, RTS/CTS, DSR/DTR  
Driver Manual.  
2.2.  
Provided by user  
The user has to provide a RS-422 cable for connecting the WS3000 to the RS-232 to RS-  
422 converter.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 5 of 14  
3.  
Hardware Connections  
The FieldServer is connected to the WS3000 as shown below.  
Configure the WS3000 according to manufacturer’s instructions.  
RS-422 Rx termination strapping  
Jumper Pins  
Chan  
Z2,  
Z2,  
Z2,  
Z1,  
Z1,  
Z1,  
Z1,  
2-7  
3-6  
4-5  
4-5  
3-6  
2-7  
1-8  
3
4
5
6
7
8
9
Use one of Channels 3-9  
WS3000  
Chan  
3,  
4,  
5,  
6,  
Connector no  
P11  
P3  
P10  
P8  
pins  
5, 6, 7, 8,  
Rx-Rx+Tx-Tx+  
Install a jumper on the  
indicated pins  
according to the  
channel used  
7,  
8,  
P1  
P9  
9,  
P2  
Dip Switch Settings  
G
H
K
L
Sw  
1-4  
5
6-7  
8
Setting  
Down (off)  
Up (on)  
Down (off)  
Up (on)  
Meaning  
RS-422  
Terminated  
Unused baud rates  
2400 baud  
RS-422  
485LDRC  
B&B Electronics RS-  
232 to RS-422  
Converter  
Power Supply  
+
Refer to Datasheet for setting other baud rates  
F
+10 to 30V DC  
GND  
RS-232  
pins  
GND  
C
D
1
8
RJ45 Socket  
(408)-262-2299  
Use one of RS-232 ports P1-P8  
FIELDSERVER  
WESTRONIC WS3000  
CONNECTION DIAGRAM  
FieldServer  
BASE NAME:  
FILE NAME:  
DATE: 4/2/04  
BY: MC  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 6 of 14  
4.  
Configuring the FieldServer as a WS3000 TABS Client  
For a detailed discussion on FieldServer configuration, please refer to the FieldServer  
Configuration Manual. The information that follows describes how to expand upon the factory  
defaults provided in the configuration files included with the FieldServer (See “.csv” files  
provided with the FieldServer).  
This section documents and describes the parameters necessary for configuring the FieldServer  
to communicate with a WS3000 TABS Server. The configuration file tells the FieldServer about  
its interfaces, and the routing of data required. In order to enable the FieldServer for WS3000  
TABS communications, the driver independent FieldServer buffers need to be declared in the  
“Data Arrays” section, the destination device addresses need to be declared in the “Client Side  
Nodes” section, and the data required from the Servers needs to be mapped in the “Client Side  
Map Descriptors” section. Details on how to do this can be found below.  
Note that in the tables, * indicates an optional parameter, with the bold legal value being the  
default.  
4.1.  
Data Arrays/Descriptors  
Section Title  
Data_Arrays  
Column Title  
Function  
Legal Values  
Up to 15 alphanumeric  
characters  
Data_Array_Name  
Data_Format  
Provide name for Data Array  
Provide data format. Each Data Array  
can only take on one format.  
Byte  
Number of Data Objects. Must be  
larger than the data storage area  
required for the data being placed in  
this array.  
Data_Array_Length  
1-10,000  
Example  
// Data Arrays  
//  
Data_Arrays  
Data_Array_Name,  
Points_0,  
Data_Format,  
byte,  
Data_Array_Length  
2048  
There are 8 bytes per display allowed. Eight bytes will represent the 64 points per display.  
A maximum of 256 displays per slave gives 2048 bytes per slave.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 7 of 14  
4.2.  
Client Side Connection Descriptors  
Section Title  
Connections  
Column Title  
Function  
Specify which port the device is connected to the  
FieldServer  
Legal Values  
P1-P81  
Port  
1200, 2400, 4800,  
9600  
Baud*  
Specify baud rate  
Parity*  
Specify parity  
Even, Odd, None  
Data_Bits*  
Specify data bits  
Specify stop bits  
Specify protocol used  
7, 8  
Stop_Bits*  
Protocol  
1, 2  
Ws3000_tabs  
None  
Handshaking* Specify hardware handshaking  
NOTE: Refer to the TABS collection port settings on the WS3000 for setting up the serial  
communication settings on the FieldServer. Also remember to change the baud rate setting  
on the RS-232 to RS-422 converter if necessary.  
Example  
// Client Side Connections  
Connections  
Port,  
P1,  
Baud,  
2400,  
Parity,  
Odd,  
Protocol,  
ws3000_tabs,  
Handshaking  
None  
4.3.  
Client Side Node Descriptors  
Section Title  
Nodes  
Column Title  
Function  
Legal Values  
Up to 32 alphanumeric  
characters  
Node_Name  
Provide name for node  
TABS device station address of  
physical Server node  
Specify protocol used  
Specify which port the device is  
connected to the FieldServer  
Node_ID  
Protocol  
Port  
0-31  
Ws3000_tabs  
P1-P81  
Example  
// Client Side Nodes  
Nodes  
Node_Name,  
Tabs_0,  
Node_ID,  
0,  
Protocol,  
ws3000_tabs,  
Port  
P1  
1
Not all ports shown are necessarily supported by the hardware. Consult the appropriate Instruction  
manual for details of the ports available on specific hardware.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 8 of 14  
4.4.  
4.4.1.  
Client Side Map Descriptors  
FieldServer Specific Map Descriptor Parameters  
Column Title  
Function  
Name of this Map  
Descriptor  
Legal Values  
Up to 32 alphanumeric  
characters  
Map_Descriptor_Name  
Name of Data Array where  
data is to be stored in the  
FieldServer  
One of the Data Array  
names from “Data Array”  
section above  
Data_Array_Name  
Starting location in Data  
Array  
0 to maximum specified in  
“Data Array” section above  
RDBC  
Data_Array_Location  
WRBX ( Only for use to  
execute remote control  
commands. See Map  
Descriptor examples. )  
Function of Client Map  
Descriptor  
Function  
Length  
The length of the Map  
Descriptor  
1
4.4.2.  
Driver Specific Map Descriptor Parameters  
Column Title  
Function  
Legal Values  
One of the node names  
specified in “Client Node  
Descriptor” above  
Name of Node to fetch data  
from  
Node_Name  
Parms_DA  
Specifies the name of the  
Data Array that will hold 0 to 20 alphanumeric  
remote control command characters  
parameters  
Specifies the offset into the  
0 to maximum offset for  
parameters Data Array  
length of the parameter  
where the remote control  
Data Array  
Parms_DA_Offset  
parameters start  
4.4.3.  
Timing Parameters  
Column Title  
Scan_Interval  
Function  
Rate at which data is polled >0.1s  
Legal Values  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 9 of 14  
4.4.4.  
Map Descriptor Example 1  
// Client Side Map Descriptors  
Map Descriptors  
Map_Descriptor_Name, Scan_Interval,  
Data_Array_Name,  
Points_0,  
Data_Array_Offset,  
0,  
Function,  
rdbc,  
node_name  
Tabs_0  
Point_data_0,  
1.0s,  
This can be any  
name but each  
name must be  
unique. Name will  
appear in  
FieldServer Map  
Descriptor status  
information screens.  
The rate  
at which  
the TABS  
device will  
be polled.  
The Data Array name  
must be one found  
under Data_Arrays. Data  
from the scan will be  
stored in the array at  
Data_Array_Offset.  
This  
value  
Only a read  
function  
allowed i.e.  
Data to be  
read from the  
TABS device.  
Node name must be one  
found under Nodes,  
Node_name The  
node_name identifies  
the station address of  
the TABS device ( 0-31).  
specifies the offset  
into the Data Array  
where the data  
fetched will be  
stored.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 10 of 14  
4.4.5.  
Map Descriptor Example 2: Remote Control Commands  
// Client Side Map Descriptors  
Map Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function,  
Node_name, Parms_DA,  
Parms_DA_Offset, Length  
Points_write,  
Write_triggers,  
0,  
wrbx,  
Tabs_0,  
Write_parms, 0, 1  
Parameters arrangement in Parms_DA  
Position from Parms_DA_Offset Description  
0
Display number 1  
1
2
3
Point number 1 ( 0-63 )  
Control type 1 ( 0, 1, 2, 128-255)  
Display number 2  
4
5
..  
Point number 2 ( 0-63 )  
Control type 2 ( 0, 1, 2, 128-255)  
..  
57  
58  
59  
Display number 20  
Point number 20 ( 0-63 )  
Control type 20 ( 0, 1, 2, 128-255)  
Note: To trigger the remote control command, load the parameters into the Data Array as shown above and then write the number of  
points to control into the Data Array specified by Data_Array_Name at Data_Array_Offset. Valid number of points are 1 to 20.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 11 of 14  
5.  
Configuring the FieldServer as a WS3000 TABS Server  
For a detailed discussion on FieldServer configuration, please refer to the FieldServer  
Configuration Manual. The information that follows describes how to expand upon the factory  
defaults provided in the configuration files included with the FieldServer (See “.csv” files  
provided with the FieldServer).  
This section documents and describes the parameters necessary for configuring the FieldServer  
to communicate with a WS3000 TABS Client. The configuration file tells the FieldServer about  
its interfaces, and the routing of data required. In order to enable the FieldServer for WS3000  
TABS communications, the driver independent FieldServer buffers need to be declared in the  
“Data Arrays” section, the FieldServer virtual node(s) needs to be declared in the “Server Side  
Nodes” section, and the data to be provided to the Clients needs to be mapped in the “Server  
Side Map Descriptors” section. Details on how to do this can be found below.  
Note that in the tables, * indicates an optional parameter, with the bold legal value being the  
default.  
5.1.  
Server Side Connection Descriptors  
Section Title  
Connections  
Column Title  
Function  
Specify which port the device is  
connected to the FieldServer  
Specify baud rate  
Specify parity  
Specify data bits  
Specify stop bits  
Legal Values  
Port  
P1-P82  
Baud*  
Parity*  
Data_Bits*  
1200, 2400, 4800, 9600  
Even, Odd, None  
7, 8  
Stop_Bits*  
Protocol  
1, 2  
Specify protocol used  
Ws3000_tabs  
None  
Handshaking*  
Specify hardware handshaking  
Time Server waits before  
responding to a poll  
Turnaround_delay*  
0.01s, or >= 0  
NOTE: Refer to the TABS collection port settings on the WS3000 for setting up the serial  
communication settings on the FieldServer. Also remember to change the baud rate  
setting on the RS-232 to RS-422 converter if necessary.  
Example  
// Server Side Connections  
Connections  
Port,  
P1,  
Baud,  
2400,  
Parity,  
Odd,  
Protocol,  
ws3000_tabs, None,  
Handshaking, Turnaround_delay  
0.01s  
2
Not all ports shown are necessarily supported by the hardware. Consult the appropriate Instruction  
manual for details of the ports available on specific hardware.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 12 of 14  
5.2.  
Server Side Node Descriptors  
Section Title  
Nodes  
Column Title  
Function  
Legal Values  
Up to 32 alphanumeric  
characters  
Node_Name  
Node_ID  
Provide name for node  
TABS device station address  
of physical Server node  
Specify protocol used  
0-31  
Protocol  
Port  
Ws3000_tabs  
Port this node is connected to P1-P83  
Example  
// Server Side Nodes  
Nodes  
Node_Name,  
Tabs_0,  
Node_ID,  
0,  
Protocol,  
ws3000_tabs,  
Port  
P1  
5.3.  
5.3.1.  
Server Side Map Descriptors  
FieldServer Specific Map Descriptor Parameters  
Column Title  
Function  
Name of this Map  
Descriptor  
Legal Values  
Up to 32 alphanumeric  
characters  
Map_Descriptor_Name  
Name of Data Array where  
data is to be stored in the  
FieldServer  
One of the Data Array  
names from “Data Array”  
section above  
Data_Array_Name  
Starting location in Data  
Array  
Function of Server Map  
Descriptor  
0 to maximum specified in  
“Data Array” section above  
Data_Array_Location  
Function  
Passive  
5.3.2.  
Driver Specific Map Descriptor Parameters  
Column Title  
Function  
Legal Values  
One of the node names  
specified in “Server Node  
Descriptor” above  
The TABS address of this  
node  
Node_Name  
3
Not all ports shown are necessarily supported by the hardware. Consult the appropriate Instruction  
manual for details of the ports available on specific hardware.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 13 of 14  
5.3.3.  
Map Descriptor Example.  
// Server side Map Descriptors  
Map Descriptors  
Map_Descriptor_Name, Data_Array_Name, Data_Array_Offset, Function, node_name  
Point_data_0,  
Points_0,  
0,  
passive,  
Tabs_0  
This value  
This can be  
The Data  
Function may  
The TABS  
device’s  
station  
address (0 –  
31).  
specifies the  
offset into the  
Data Array  
where the  
data will be  
stored for  
any name but  
each name  
must be  
unique. Name  
will appear in  
FieldServer  
Map  
Descriptor  
status  
information  
screens.  
Array name  
must be one  
found under  
Data_Arrays  
Data will be  
sent from  
this array to  
the device  
polling this  
TABS  
not be read or  
write since it  
implements a  
Server.  
Function may  
only be  
testing with  
scripts.  
passive.  
device.  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  
FS-8700-70 WS3000 Tabs Manual  
Page 14 of 14  
THIS PAGE INTENTIONALLY LEFT BLANK  
FieldServer Technologies 1991 Tarob Court Milpitas, California 95035 USA Web:www.fieldServer.com  
Tel: (408) 262-2299 Fax: (408) 262-9042 Toll_Free: 888-509-1970 email: [email protected]  

NAD C545BEE User Manual
Motorola MOTOROKR Z6 User Manual
Motorola Cell Phone 6806800C47B User Manual
Fujitsu MHZ2120BJ User Manual
Disney DCR4500 P User Manual
Classe Audio CDP 102 User Manual
Bunn Coffeemaker U3A User Manual
Antec VERIS MX 100 User Manual
Antec VERIS MX 1 User Manual
Albatron Technology KI51PV 754 User Manual