Fellowes DM10C User Manual

Help Line  
Fellowes  
Australia  
Canada  
+1-800-33-11-77  
+1-800-665-4339  
+1-800-234-1185  
+1-800-955-0959  
México  
United States  
Australia  
Benelux  
+61-3-8336-97000  
+31-(0)-76-523-2090  
+ 1-905-475-6320  
Canada  
Deutschland  
France  
+ 49-(0)-5131-49770  
+ 33-(0)-1-30-06-86-80  
+ 39-(0)-71-730041  
+ 81-(0)-3-5496-2401  
+ 82-(0)-2-3462-2884  
+ 60-(0)-35122-1231  
+ 48-(22)-771-47-40  
+ 34-91-748-05-01  
+(65)-6221-3811  
Italia  
Japan  
Korea  
Malaysia  
Polska  
Spain  
Singapore  
United Kingdom  
United States  
+ 44-(0)-1302-836836  
+ 1-630-893-1600  
DM10C  
Please read these instructions before use  
Get More Done Today  
© 2005 Fellowes. Printed in China. Form No. 401188  
Set-Up  
Product Profile  
For safety reasons, this model will operate only if the shredder head (6) is in the correct  
position on the cabinet (2) and used with supplied basket (3).  
This product is built to shred paper, staples, small paper clips, credit  
cards, CDs and DVDs (CDs and DVDs in designated slot). It is not built to  
shred transparencies, adhesive labels, newspaper, cardboard, large paper  
clips, or plastic (other than items noted above). Attempting to shred items  
not intended for this shredder may cause damage.  
Position shredder head over cabinet. Place shredder head on top of cabinet as shown in  
Figure A.  
Firmly push down on four corners of shredder head to "lock" shredder head into position.  
Push basket into shredder cabinet as shown in Figure B.  
Note: To disassemble, pull out basket, hold cabinet down by placing foot on bottom shelf,  
and firmly pull up on shredder head.  
Confetti-cut (DM10C)  
Paper  
Sheet capacity*  
Paper shred size  
10 sheets  
5/32" x 1-3/8" (3.9 x 3  
9" (229 mm)  
Operation  
5
mm)  
For convenience, your shredder is equipped with an automatic-start sensor (8). This  
means that when the control switch (9) is in the automatic [I] position, the shredder will  
start running when you put paper into it and stop a few seconds after the paper has  
passed through. Because the sensor cannot tell the difference between paper and other  
objects, this feature can also be a hazard, especially to children and pets. To avoid acci-  
dents, turn off the shredder as soon as you are finished. Unplug shredder if it will not be  
used for an extended period.  
Maximum paper width  
Speed (at paper capacity)  
Maximum running time (duty cycle on)  
Automatic cool-down period  
Recommended daily capacity  
Credit Cards  
14 ft/min  
20 minutes  
40 minutes  
25-50 shredding passes  
Credit card capacity  
1
Recommended daily capacity  
CDs/DVDs  
CDs/DVDs capacity  
Recommended daily capacity  
10  
To shred  
Press control switch (9) to automatic [I] position. Green ready light (4) should turn on.  
1
10  
PAPER  
Feed paper straight into entry (1), releasing when shredder begins shredding; see Product  
Profile for limits on paper width, shreddable items, sheet capacity, etc.  
Shred no more than 20 minutes; shredding longer will cause shredder to turn itself off for  
40 minutes to cool down.  
*Based on 8-1/2 x 11” (75 g/20 lb.) paper with shredder operating at rated voltage; heavier paper, high humidity, or  
other than rated voltage may reduce sheet capacity.  
NOTE: These products have met international standards for motor temperature rise: Independent product testing  
agencies approved each model at the midpoint of its sheet-per-pass limit. In the tests, the agencies also varied the  
available voltage 10% below and 6% above its normal range, stopping shredding only to empty the basket.  
Press control switch to off [O] position after cutting has stopped.  
CDs, or DVDs  
Slide safety cover (12) to the front to expose the CD entry (11).  
Hold CD or DVD at the edge and feed one at a time, straight into entry (11) releasing  
when shredding begins. Shredder will stop when item has passed through entry. CDs and  
DVDs will be shredded into small particles.  
Slide cover (12) to the back when done shredding media.  
CAUTION: Do not hold CD or DVD with finger through the center ring while feeding into  
shredder.  
IMPORTANT SAFETY INSTRUCTIONS  
READ ALL INSTRUCTIONS BEFORE USING  
While assembling shredder  
Check shredder for damage or defects; some paper particles in the basket are normal  
due to product testing and does not indicate a defect.  
If the cord is damaged do not replace cord or use the machine. Return machine  
for a replacement.  
Avoid touching exposed blades on underside of confetti-cut shredder head.  
Plug power cord in an outlet that can easily be reached.  
Do not place shredder near or over a heat or water source.  
In case of a paper jam, which may occur if the shredder is pushed beyond its specified  
capabilities, press the control switch to the off [O] position and empty the basket if full.  
Then:  
1) Press and hold control switch in reverse [R] position and attempt to back paper out of  
shredder.  
2) If shredder jams in reverse mode, press control switch to automatic [I] position and  
attempt to continue shredding operation.  
3) If shredder jams again, alternate control switch slowly between reverse [R] and automat-  
ic [I] positions to attempt to move jammed paper completely through shredder.  
While operating shredder  
Keep hands and hanging objects (jewelry, ties, loose clothing,  
long hair, etc.) away from paper entry.  
Keep children and pets away from the shredder.  
When not in use  
Always turn off and unplug shredder  
Unplug before emptying basket  
If you are unable to clear the jam using this method, turn off and unplug the shredder;  
remove the wastebasket from cabinet and carefully remove any paper extending below the  
cutting cylinders; empty the wastebasket; insert wastebasket and repeat jam clearing pro-  
cedure.  
Do not open shredder head: Danger of electric shock.  
NOTE: Do not use flammable synthetic oil, petroleum-based products or  
aerosols of any kind on or near product at any time.  
3
4
Maintenance  
Limited Warranty  
Regular emptying of the basket is important to ensure the smooth operation of the  
cutting cylinders. If you can see paper in the basket window (7), turn off the shredder, pull  
out the basket and empty basket contents.  
Fellowes, Inc. warrants the cutting cylinders of the machine to be free from defects in  
material and workmanship for 5 years from the date of purchase by the original con-  
sumer. Fellowes warrants all other parts of the machine to be free of defects in material  
and workmanship for 1 year from the date of purchase by the original consumer. If any  
part is found to be defective during the warranty period, your sole and exclusive remedy  
will be repair or replacement, at Fellowes’ option and expense, of the defective part.  
Regular oiling of the shredder is also necessary to ensure proper performance. If you  
are running the shredder at or near capacity, we recommend oiling it monthly. Using  
Fellowes Powershred Lubricant #35250 or other non-aerosol vegetable-based oil in a  
long-nozzle container:  
This warranty does not apply in cases of abuse, mishandling or unauthorized repair. ANY  
IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A  
PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WAR-  
RANTY PERIOD SET FORTH ABOVE. IN NO EVENT SHALL FELLOWES BE LIABLE FOR  
ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES ATTRIBUTABLE TO THIS PRODUCT.  
This warranty gives you specific legal rights. You may have other legal rights that vary from  
this warranty. The duration, terms and conditions of this warranty are valid worldwide,  
except where different limitations, restrictions or conditions may be required by local law.  
• Apply oil over full width of paper entry (1) with shredder in off [O] position.  
• Press control switch to automatic [I] position which will cause shredder to run  
for about 2 seconds.  
• Press and hold control switch in reverse [R] position for 3-5 seconds.  
• Repeat above automatic [I] and reverse [R] sequence three times.  
REMINDER: Do not use flammable synthetic oil, petroleum-based products or  
aerosol lubricants of any kind in or near the shredder at any time.  
To obtain service under this warranty, please contact us (see back cover) or your dealer.  
Troubleshooting  
If you have a problem with your shredder, check the symptoms and remedies below. If you  
cannot solve the problem this way, contact Fellowes Customer Service. Do not open  
shredder head to attempt repair: It could expose you to serious electric shock and will  
void your warranty.  
Symptom  
Remedy  
Shredder does not start or stops while  
shredding.  
• Make sure shredder is plugged in and  
switch is in automatic [I] position.  
• If paper appears to be jammed. Follow  
instructions under Operation.  
• Check basket position; basket must be  
pushed all the way in the cabinet.  
Follow instructions under Set-Up.  
Overheat light (10) turns on and shredder  
will not operate.  
• Wait 40 minutes for shredder to cool  
down before trying again.  
Red display light (5) turns on and shredder  
will not operate.  
• If paper appears to be jammed. Follow  
instructions under Operation.  
• Check basket position; basket must  
be pushed all the way in the cabinet.  
Follow instructions under Set-Up.  
Shredder squeaks, grinds or runs below  
capacity.  
• Oil cutting cylinders. Follow instructions  
under Maintenance.  
Shredder continues to run for a few sec-  
onds after shredding has been completed.  
• No action required. This is a self-clean-  
ing function.  
5
6

Motorola international 2700 User Manual
Magic Chef MCCM1NB12 User Manual
Kyocera 7135 Smartphone User Manual
IBM DTLA 305010 User Manual
GE 681131691017 User Manual
Dacor Flushing System Kit ACFS User Manual
Cecilware Java MC 5 User Manual
Bose Companion 5 User Manual
Black & Decker ODC350 User Manual
Black & Decker DCM902WH User Manual