AM/FM Alarm Clock Radio
with SmartSet®
Automatic Time Setting System
and Sure Alarm
(U.S. Patent No. 6,567,344)
OWNER’S MANUAL
CKS1701
CKS1701_032306.p65
22
23/3/2006, 14:44
Congratulations!
And thank you for purchasing the SmartSet® Clock Radio from Emerson Research.
SmartSet® is the world’s first and only LED clock radio that will automatically set
itself to the correct ‘Year’, ‘Month’, ‘Date’, and ‘Time’ as soon as you plug it in. The
only thing you have to do is tell the SmartSet® what time zone you are in, and the
built in computer does everything else for you immediately. And not only the first
time, but every time the power is interrupted as well.
We all know how annoying it is to wake up in the morning and see the dreaded
flashing “12:00” display on our clocks or clock radios. This means that your power
was interrupted some time during the night while you were sleeping and your clock
doesn’t know what time it is anymore. Unfortunately it probably also means that
you are late for work, or for school, again. But with your SmartSet® Clock Radio the
dreaded flashing “12:00” display is a thing of the past. The SmartSet® resets itself
as soon as the power is restored and gets you up on time, every time.
We've also included a Daylight Saving Time (DST) ON/OFF switch to make the
change from Standard Time to Daylight Saving Time as simple as possible. And
best of all, the long life lithium battery backup battery is already installed in your
radio. You don’t have to remember to put a new 9-volt battery in your radio every 6
months. Under normal circumstances the lithium battery can last for up to 5 years,
and when it does need to be changed, a low battery indicator will flash to let you
know. The CR2430 lithium battery is available almost anywhere that batteries are
sold.
Someday all clocks and clock radios may be this smart. But today the technology
is only available from Emerson Research.
We’re sure you’ll be happy and amazed by your SmartSet® Clock Radio, and that it
will give you many years of enjoyment and dependable service.
Once again, all of us at Emerson Research thank you for your purchase.
2
CKS1701_032306.p65
2
23/3/2006, 14:44
IMPORTANT NOTES
• Avoid installing this unit in places • Operate controls and switches as
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much
heat, places lacking ventilation or dusty
areas, places subject to constant
vibration and/or humid or moist areas.
described in the manual.
• Before turning on the power, make
certain that the power cord is properly
installed.
• When moving the set, be sure to first
disconnect the AC power cord.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequencyenergy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
3
CKS1701_032306.p65
3
23/3/2006, 14:44
PREPARATION FOR USE
Unpacking And Set-up
• Remove the radio from the carton and remove all packing material from the
radio. We suggest that you save the packing material, if possible, in the unlikely
event that your radio ever needs to be returned for service. The original carton
and packing material is the only safe way to pack your radio to protect it from
damage in transit.
• Remove any descriptive labels or stickers on the front or top of the cabinet. Do
not remove any labels or stickers from the back or bottom of the cabinet.
• Note the serial number on the bottom of your radio and write this number in the
space provided on the Warranty page of this manual.
• Place your radio on a level surface such as a table, desk or shelf, convenient
to an AC outlet, out of direct sunlight, and away from sources of excess heat,
dirt, dust, moisture, humidity, or vibration.
• Unwind the AC power cord and extend it to its full length. The FM antenna is
built in to this cord. It must be fully extended to provide the best FM reception.
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
4
CKS1701_032306.p65
4
23/3/2006, 14:44
Power Source
This radio is designed to operate on normal 120V 60Hz AC power only. Do not
attempt to operate the radio on any other power source. You could cause damage
to the radio that is not covered by your warranty.
This radio should be connected to an AC outlet that is always ‘live’. Do not connect
it to an outlet that is controlled by a wall switch. When the power to the radio is
interrupted, the built in lithium battery takes over to maintain the time and alarm
settings. To maximize the life of the lithium battery keep the radio connected to a
‘live’ AC outlet at all times.
You will note that this system is equipped
with a polarizedAC power plug having one
blade wider than the other. This is a safety
feature. If this plug does not fit into your
existing AC outlet, do not try to defeat this
safety feature by filing the wide blade to
make it fit into your outlet. If this plug will
not fit into your outlet, you probably have
AC Outlet
an out-dated non-polarized AC outlet. You
AC Plug
should have your outlet changed by a
qualified licensed electrician.
Sure Alarm battery Back-Up System
This SmartSet® Clock Radio includes a Sure Alarm battery back-up circuit that can
wake you up even if the power is ‘Off’ at the selected wake up time. If your power
is ‘Off’ at the selected wake up time the clock display will be off and the radio will
not operate, but a separate mini-buzzer will turn ‘On’ automatically to wake you up,
even if you had selected the “Wake to Radio” option. The Sure Alarm will sound for
30 seconds and then shut off automatically.
To stop the Sure Alarm buzzer immediately, press the ALARM button. Pressing
the SNOOZE button has no effect during Sure Alarm operation.
NOTE: In order to maximize the life of the built in lithium battery, please be
sure to set the OFF-ON-BUZZ-AUTO selector switch to the “OFF” position if
the radio will be disconnected from the AC outlet for more than a few hours.
This will prevent the Sure Alarm from turning ‘On’ unecessarily.
5
CKS1701_032306.p65
5
23/3/2006, 14:44
LOCATION OF CONTROLS AND INDICATORS
Front Panel
2
3
4
5
1
7
6
3
Top Panel
17
16
15
14
13
12
18
19
11
10
9
8
Left Side Panel
Right Side Panel
24
23
22
21 20
6
CKS1701_032306.p65
6
23/3/2006, 14:44
1.) AM indicator.
2.) Time/Date Display.
3.) Dial Pointers.
4.) FM Dial Scale.
5.) AM Dial Scale.
6.) LOW BATT. LED Indicator.
7.) Back Up Battery Compartment (Bottom Cabinet).
8.) SNOOZE (SLEEP OFF) Button.
9.) TIME ZONE Button.
10.) TIME Setting Button.
11.) SLEEP Button (Sleep To Music Timer).
12.) MONTH/DATE Setting Button.
13.) OFF-ON-BUZZ.-AUTO Selector Switch.
14.) AUTO ON Indicator.
15.) AC Power Cord (Back Cabinet).
16.) ALARM setting Button.
17.) Speaker (Top Cabinet).
18.) SET + Button.
19.) SET – Button.
20.) VOLUME Control.
21.) BAND (AM/FM) Selector Switch.
22.) TUNING Control.
23.) DST (ON/OFF) Button.
24.) Display DIMMER (HI/LO) Selector Switch.
7
CKS1701_032306.p65
7
23/3/2006, 14:44
OPERATING INSTRUCTIONS
Daylight Saving Time (DST) ON/OFF Switch
IMPORTANT: The Daylight Saving Time (DST) ON/OFF switch is located on
the left side panel. This switch was set to the “OFF” position at our factory
prior to shipment. At the beginning of Daylight Saving Time set the DST switch
to the “ON” position. The time will advance by one hour. At the end of Daylight
Saving Time set the DST switch to the “OFF” position. The time will back up
by one hour.
The first time you connect your new SmartSet® clock radio to the AC outlet the
internal computer will automatically set the display to show the correct
EASTERN STANDARD TIME. This is the initial default setting. The display will
scan for few seconds and then show the correct Eastern Standard Time. If you are
doing this during Daylight Saving Time, slide the DST ON/OFF switch, located on
the left side panel, to the “ON” position. The display will then show the correct
Eastern Daylight Time.
DST ON/OFF Switch
If you live in the Eastern Time zone, there’s nothing else to do. Your clock is set
correctly and running. If you do not live in the Eastern Time zone you must change
the default zone display to your own zone. You only do this one time and the
SmartSet® will remember the new default zone setting and will always return to
that setting after a power interruption.
8
CKS1701_032306.p65
8
23/3/2006, 14:44
There are 7 time zones programmed into your SmartSet® clock radio as follows:
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE 5
ZONE 6
ZONE 7
—
—
—
—
—
—
—
Atlantic Time
Eastern Time (Default Setting)
Central Time
Mountain Time
Pacific Time
Yukon Time
Hawaiian Time
To change the default time zone display, depress the TIME ZONE button.
The number “2” will appear on the display
indicating that the default zone is ZONE 2,
Eastern Time.
Hold the TIME ZONE button and then press either the SET + or – buttons until
your own time zone appears on the display, then release the buttons. The clock
display will change to the correct time in the time zone you selected. The clock will
always return to the correct time in the zone you selected after every power
interruption. If you move to a different time zone, simply change the default zone
display to the new zone and the SmartSet® will remember that setting for you.
Date Display
To see the correct date at any time, depress the MONTH/DATE button. The display
changes from Time to Month and Date (MM/DD).
For example, May 21st will appear as “5 21”.
When you release the MONTH/DATE button the display returns to the correct
time.
9
CKS1701_032306.p65
9
23/3/2006, 14:44
Year Display
To see the correct year, depress the MONTH/DATE and TIME buttons together.
The display changes from time to year.
When you release the MONTH/DATE and TIME buttons the display returns to the
correct time.
Manual Time Adjustments
Some people like to set their clocks 5 to 10 minutes fast to make sure that they will
always be on time. Even though the SmartSet® sets the time by itself, you still have
the option of adjusting the time manually if you wish.
To manually adjust the time display depress and hold the TIME button, and press
either the SET + or – buttons to adjust the time display ahead or back as desired.
Each press of the SET + or – buttons will change the display by one minute. If you
hold the SET + or – buttons the display will continue to change. The display will
change slowly at first, one minute at a time. But if you continue holding the SET +
or – buttons the display will change rapidly.
NOTE: If you manually adjust the time, your new setting is entered into the
SmartSet® memory. If the power is interrupted, the display will return to your
new setting, not the original setting, when the power is restored.
10
CKS1701_032306.p65
10
23/3/2006, 14:44
Adjusting The Wake Up Time
1.) Depress and hold the ALARM setting button. The display will change from the
correct time to the Alarm wake up time.
2.) While holding the ALARM setting button, depress either the SET + or – button
to move the display ahead or back to your desired wake up time.
3.) When the desired wake up time appears on the display, release the SET + or –
buttons.
Note: Be sure that you have set the wake up time correctly by observing the
AM indicator. If the AM indicator is ‘On’ the wake up time is “AM”. If the AM
indicator is ‘Off’, the wake up time is “PM”.
4.) When the desired wake up time (AM or PM) appears on the display, release
the ALARM setting button.
Checking The Wake Up Time
Whenever you want to check the wake up time setting, simply press the ALARM
setting button. The display will change from correct time to wake up time.
Release the ALARM setting button to return to correct time.
11
CKS1701_032306.p65
11
23/3/2006, 14:44
Listening To The Radio
1.) Set the BAND selector to the desired band, AM or FM.
2.) Set the VOLUME control to a low setting.
3.) Switch the OFF-ON-BUZZ-AUTO selector switch to the “ON” position.
4.) Select your desired station with the TUNING control.
5.) Adjust the VOLUME control to the desired setting.
6.) When you are finished listening, Switch the OFF-ON-BUZZ-AUTO selector
switch to the “OFF” position.
Antenna Information
AM – The AM bar antenna is inside the cabinet. If AM reception is weak, change
the position of cabinet until the internal antenna picks up the strongest signal.
FM – The FM antenna is built in to the AC power cord. If FM reception is weak try
varying the position and direction of the power cord until you find the strongest
signal.
12
CKS1701_032306.p65
12
23/3/2006, 14:44
Wake To Radio
1.) Turn the radio ‘On’ and select the band, station, and volume level that you wish
to hear when the alarm comes on.
2.) Reconfirm the wake up time by pressing the ALARM button.
3.) Set the OFF-ON-BUZZ-AUTO selector switch to the “AUTO” position. The
AUTO ON indicator will light up to confirm that the alarm is set.
4.) At the selected wake up time the radio will turn ‘On’. It will play for one hour and
then shut off automatically.
5.) To stop the radio sooner, press the ALARM button. The radio will stop but the
alarm remains set and will turn the radio on again at the same time on the
following day.
6.) If you do not want the alarm to turn the radio on the following day, set the
OFF-ON-BUZZ-AUTO selector switch to the “OFF” position.
Wake To Buzzer (Crescendo Alarm)
1.) Reconfirm the wake up time by pressing the ALARM button.
2.) Set the OFF-ON-BUZZ-AUTO selector switch to the “BUZZ.” position. The
AUTO ON indicator will light up to confirm that the alarm is set.
3.) At the selected wake up time the buzzer will sound. It will begin softly and
gradually increase in volume to wake you up. It will continue for one hour and
then shut off automatically.
4.) To stop the radio sooner, press the ALARM button. The buzzer will stop but
the alarm remains set and will turn the buzzer on again at the same time on the
following day.
5.) If you do not want the alarm to turn the buzzer on the following day, set the
OFF-ON-BUZZ-AUTO selector switch to the “OFF” position.
13
CKS1701_032306.p65
13
23/3/2006, 14:44
Snooze Alarm
After the radio or buzzer alarm sounds in the morning you may press the SNOOZE
(SLEEP OFF) Bar for a few more minutes sleep. The alarm will stop for
approximately 9 minutes and then turn on again. You may repeat the Snooze
operation up to seven times if desired, but after the seventh time the alarm will not
turn on again.
Sleep To Music Timer
You can program the sleep timer to play the radio for up to 90 minutes and then
shut off automatically.
1.) Press the SLEEP button.
The display will briefly show “10” and the
radio will begin to play.
After 10 minutes the radio will shut off automatically. Each time you press the
SLEEP button the sleep timer will start at 10 minutes. This is the sleep timer
default setting.
2.) To increase or decrease the amount of time that the radio will play before
shutting off, hold the SLEEP button and press either the SET + or – button to
change the display to the desired sleep time, up to a maximum of 90 minutes
or a minimum of 2 minutes.
NOTE: When you change the sleep timer from the 10 minute default setting to
a different setting, the new setting becomes the default setting. Whenever you
activate the sleep timer it will begin with your new default setting and count
down to zero from that point.
3.) To cancel the sleep timer before it counts down to “00” and shut the radio ‘Off’
immediately, press the SNOOZE (SLEEP OFF) Bar.
IMPORTANT: Remember that the station and volume settings you choose for the
Sleep To Music operation are the same settings you will hear if you set the alarm
for wake to radio the following morning.
Dimmer Control
The DIMMER control was set to the HI (High) position at our factory. If you find the
clock display is too bright in a darkened room, set the Dimmer control to the LO
(Low) position.
14
CKS1701_032306.p65
14
23/3/2006, 14:44
Changing The Lithium Battery
Like all batteries, eventually the built in lithium battery will need to be replaced. A
number of factors, such as, the length of time between the date the radio was
manufactured and the date you plugged it in for the first time determine the amount
of time before replacement. During this initial storage period, the lithium battery is
supplying power to the SmartSet® computer memory. Once you plug the radio in,
your household outlet supplies the power, and the battery is not being used. A
fresh lithium battery can supply power to the SmartSet® computer for at least 3
years even if it is never connected to an AC power supply. If your radio was
connected to your AC supply within a few months after it was manufactured, and
you experience only the normal, nuisance type, short duration power interruptions,
your battery may last for up to 5 years or even longer.
When the battery power drops below a certain level, the LOW BATT. indicator will
‘flash’. When you see this indicator, you should change the battery as soon as it is
convenient for you to do so. To change the battery proceed as follows:
1.) Purchase a replacement 3V lithium battery wherever batteries are sold. The
battery type is CR2430 or equivalent.
2.) Remove the battery from its package so it is ready to install.
IMPORTANT: Leave the radio power cord connected to your AC outlet. This
will provide power to the SmartSet® computer memory while the original lithium
battery is removed.
3.) Turn the radio upside down and use a small screwdriver to remove the screw
securing the battery holder to the cabinet.
BE CAREFUL NOT TO LOSE THIS SMALL SCREW!
15
CKS1701_032306.p65
15
23/3/2006, 14:44
4.) Remove the original battery from the holder and insert the new battery into the
holder the same way, observing the positive (+) direction. Slide the holder with
the new battery back into the slot in the cabinet.
5.) Replace the screw that secures the battery holder in the cabinet.
6.) Turn the radio right side up and confirm that the LOW BATT. indicator is ‘Off’.
7.) Save these instructions. You’ll have to do this again five to eight years from
now!
16
CKS1701_032306.p65
16
23/3/2006, 14:44
Resetting The Clock After A Total Memory Loss
If you do not change the built in lithium battery within a reasonable period of time
after you see the ‘flashing’ LOW BATT. warning indicator, the lithium battery may
become exhausted and will no longer be able to supply back up power to the
SmartSet® internal computer. If the unit is disconnected from the AC outlet after
the battery is exhausted, or if a power interruption occurs, the SmartSet® memory
will be lost and the clock will need to be reset when the power is restored. Be sure
to install a fresh lithium battery before you reset the clock, otherwise the clock will
need to be reset each time the power is interrupted.
If the lithium battery is exhausted and you experience an interruption in the AC
power supply, the clock will reset itself to its initial default setting when the power is
restored.
The initial default setting is “12:00 AM, Saturday, January 1st (1 1), 2005”.
If you notice that the time on your SmartSet® clock radio is completely incorrect,
press the MONTH/DATE button to see the date.
If the date display is showing “1 1” (January 1st), you probably experienced a
total memory loss.
To reset the clock after a total memory loss, proceed as follows:
1.) Follow the instructions on pages 15-16 and install a new CR2430 lithium battery
in the battery compartment.
2.) Connect the radio to your AC outlet and let the clock set itself.
3.) Depress the MONTH/DATE and TIME buttons together. The displaywill change
from ‘Time’ to ‘Year’.
While holding the MONTH/DATE and TIME buttons, press the SET + button
to set the display to the correct year, then release the buttons.
4.) Depress the MONTH/DATE button. The display will change from ‘Time’ to
‘Month/Date’ (mm/dd).
While holding the MONTH/DATE button, press the SET + button to set the
display to the correct Month andDate. When the correct Month andDate appear
on the display, release the buttons.
17
CKS1701_032306.p65
17
23/3/2006, 14:44
5.) Depress the TIME button and the SET + button to set the display to the correct
Time. Be sure to confirm that you have set the time correctly to ‘AM’ or ‘PM’ by
observing the AM indicator.
6.) After you set the time, reconfirm that the Month/Date displays are still correct.
Make final adjustments if necessary.
The SmartSet® clock memory is now reset and the new lithium battery will maintain
it for the next 5 to 8 years, depending on the number and duration of the power
outages you experience.
IMPORTANT NOTE:
After resetting the clock, don’t forget to reset your wake up times, and sleep timer
settings as well.
18
CKS1701_032306.p65
18
23/3/2006, 14:44
CARE AND MAINTENANCE
If the cabinet becomes dusty, wipe it with a soft cloth. If the cabinet becomes
smudged or dirty, clean it with a soft, slightly dampened cloth. Never allow
water or any liquid to get inside the cabinet. Never use any abrasive cleaners
or cleaning pads as these will damage the finish of your radio.
Lithium Battery Precautions
• Dispose of the old battery properly. Do not leave it lying around where a young
child or pet could play with, or swallow it. If the battery is swallowed, contact a
physician immediately.
• Battery may expolde if mistreated. Do not attempt to recharge it or disassemble
it. Do not dispose of the old battery in a fire.
TO FIND THE LOCATION AND PHONE
NUMBER OF YOUR NEAREST SERVICE
CENTER PERMITTED TO PERFORM
WARRANTY...
SERVICE
CALL TOLL FREE: 1-800-695-0098
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE,PLEASE WRITE TO:
Emerson Radio Corp.,
Consumer Affairs Dept.,
5101 Statesman Drive,
Irving, TX 75063.
19
CKS1701_032306.p65
19
23/3/2006, 14:44
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts at
an authorized Depot Repair Facility, or replace the product in our discretion. For
repair or replacement, pack your unit in a padded box, enclose your check or
money order payable to Emerson Radio Corp. in the amount of $9.00 (not required
by California residents) to cover shipping and handling costs, and enclose a copy
of your proof of purchase. Send your unit to:
Emerson Radio Corp.,
5101 Statesman Drive,
Irving, TX 75063.
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTYGIVES YOU SPECIFIC LEGAL RIGHTS, ANDYOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898M
The Serial Number can be found on the bottom cabinet. We suggest that you
record the Serial Number of your unit in the space below for future reference.
Model Number: CKS1701
Serial Number:
20
CKS1701_032306.p65
20
23/3/2006, 14:44
CKS1701-032306-01
Printed in China
CKS1701_032306.p65
21
23/3/2006, 14:44
|