Design LED 36 Pro
Elation Professional™
6122 S. Eastern Ave.
Los Angeles, Ca 90040
Rev. 5/13/2009 - visage
DESIGN LED 36 Pro™
TABLE OF CONTENS
1. General Information……………………………………………………………………… 3
a. Introduction………………………………………………………………………. 3
b. Unpacking………………………………………………………..…………..….. 3
c. Customer Support…………………………………………….………………… 3
d. Warranty Registration……………………………………………………………4
2. Safety Instructions………………………………………………………........…………. 5
3. Features……………………………………………………………………………………7
4. General Guidelines………………………………………………………………………. 8
5. Fixture Overview…………………………………………………………………………. 9
6. Mounting and Installation………………………………………………………….……. 11
a. Yoke Assembly………………………………………………………………….. 11
b. Mounting Positions……………………………………………………………… 12
c. Mounting Points…………………………………………………………………. 12
d. Clamp Mounting………………………………………………………………….12
e. Securing………………………………………………………………………….. 13
7. Understanding DMX……………………………………………………………………... 14
a. DMX Connections………………………………………………………………. 15
b. DMX Terminator…………………………………………………………………. 15
c. 3-Pin to 5-Pin Conversion……………………………………………………….16
d. Fixture DMX Addressing.……………………………..…………………………16
8. Display LED Indicators..………………………………………………………………….18
9. Display Menu..………………………………………………………………………….…19
10. DMX Traits…………………………………………………………………………………21
a. 3-Channel Mode………………………………………………………………… 21
b. 4-Channel Mode…..…………………………………………………………..… 22
c. 6-Channel Mode…..……………………………………………..……………… 23
11. Lens Replacement……… ……………………………………………………………… 25
12. Cleaning and Maintenance………………………………………………………………26
13. Warranty…………………………………………………………………………………... 27
14. Photometric Data………………………………………………………………………… 29
15. Dimensional Drawings………………………………………………….……………….. 32
16. Circuit Schematic………...……………………………………………………………….33
17. Technical Specifications…………………………………………...………….………… 34
©Elation Professional, Los Angeles Ca.
2
DESIGN LED 36 Pro™
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and
reliable LED fixtures on the market today! The Design LED 36 Pro™ has been designed to
perform reliably for years when the guidelines in this booklet are followed. Please read and
understand the instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information regarding safety during
use and maintenance.
UNPACKING: Thank you for purchasing the Design LED 36 Pro™ by Elation Professional®.
Every Design LED 36 Pro™ has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may have occurred
during shipping. If the carton appears to be damaged, carefully inspect your fixture for
damage and be sure all accessories necessary to operate the fixture have arrived intact. In
the event damage has been found or parts are missing, please contact our customer support
team for further instructions. Inside the box you should find: the fixture, a DMX XLR cable, a
safety cable, and this manual. Please do not return this unit to your dealer without first
contacting customer support at the number listed below.
CUSTOMER SUPPORT: Elation Professional® provides a customer support line, to provide
set up help and to answer any question should you encounter problems during your set up
comments or suggestions. For service related issue please contact Elation Professional®.
Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice:
Fax:
(323) 582-3322
(323) 832-9142
E-mail:
Forum:
Warning! To prevent the risk of fire and reduce the risk electrical shock do not attempt to
operate this fixture with the lens cover removed.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs
©Elation Professional, Los Angeles Ca.
3
DESIGN LED 36 Pro™
yourself. Doing so will void your manufactures warranty.
Please do not discard the shipping carton in the trash. Please recycle whenever possible.
WARRANTY REGISTRATION: The Design LED 36 Pro™ carries a two year (730 days)
limited warranty. Please fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written
on the outside of the return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included in the shipping
container. If the unit is under warranty, you must provide a copy of your proof of purchase
invoice. Items returned without a R.A. number clearly marked on the outside of the package
will be refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support at (323) 582-3322.
©Elation Professional, Los Angeles Ca.
4
DESIGN LED 36 Pro™
2. SAFETY INSTRUCTIONS
To guarantee proper and consistent operation, it is important to
follow the guidelines in this manual. Elation Professional will not
accept responsibility for damages resulting from the misuse of
this fixture due to the disregard of the information printed in this
manual.
1. To reduce the risk of fire or shock, do not expose this fixture to rain or moisture.
Although this fixture shares a case design with our outdoor rated DLED 108IP,
this version has not been approved for outdoor use. Use of this fixture outdoors
will void all manufactures warranty.
2. Always be sure that the fan and the air inlets remain clean and are never
blocked. Allow about 6” (15cm) between this fixture and other devices or a wall
to allow for proper cooling.
3. Never touch the fixture during normal operation.
4. Never look directly into the light source. You risk injury to your retina, which may
induce blindness.
5. For safe operation, follow the Installation guide described in chapter six of this
manual. Operating the Design LED 36 Pro™ without suited safety aids such as
safety cables or clamps can increase the risk of damage and/or personal injury.
6. Qualified and certified personnel should only perform installation.
7. When mounting this fixture, use only the original rigging points included with this
fixture. Any structural modification will void the original manufactures warranty
and may increase the risk of damage and/or personal injury.
8. Do not attempt to operate this fixture if the power cord has become damaged or
frayed.
9. Never open this fixture while in use.
10.This device falls under protection-class I. Therefore it is essential that the device
be grounded properly.
©Elation Professional, Los Angeles Ca.
5
DESIGN LED 36 Pro™
11.Qualified personnel should perform all electrical connections.
12.Be sure the available voltage matches the voltage requirements of the unit. Be
sure the power cord is never crimped or damaged. If the power cord is damaged,
replace it immediately with a new one of similar power rating.
13.Always disconnect from main power before performing any type of service or
any cleaning procedure.
14.Only handle the power cord by the plug. Never pull out the plug by tugging the
wire portion of the cord.
15.Please be aware that damages caused by modifications to the device are
not subject to warranty.
Important Notice: Damages resulting from the disregard of safety and general user
instructions found in this user manual are not subject to any warranty claims.
©Elation Professional, Los Angeles Ca.
6
DESIGN LED 36 Pro™
3. FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
Low power consumption
Minimal heat emission
Maintenance free operation
Equipped with 36 3-Watt (12 x red, 12 x green, 12 x blue)
Silent Operation, convection cooled, no fans
100,000 hours rated LED life
Linear RGB Color Mixing, infinite color possibilities
47˚ Standard Beam Angle (15˚ Lens - Optional 25˚ & 45˚ Lens Kits Available)
USITT DMX-512 Complaint
Preprogrammed colored macros
Strobe-effect with a maximum flash rate of 18fps
DMX-controlled operation or stand-alone operation with Master/Slave-function
8 built-in programs can be called up via DMX-controller
~ 48 preprogrammed scenes per program
Sound-controlled via built-in microphone
Three DMX Modes:
•
•
6 DMX channels
4 DMX channels
3 DMX channels
•
•
•
•
•
DMX-control via standard DMX-controller
Power Switching Electronic Power Supply 100v~240v
Flicker-free operation for television and film
Compact design: fits in 12” box truss
0%~100% Dimming (two dimming options; linear & standard)
©Elation Professional, Los Angeles Ca.
7
DESIGN LED 36 Pro™
4. GENERAL GUIDELINES
This fixture is a professional lighting effect designed for use on stage, in nightclubs, in
theatres, and other types of architectural installations. Do not attempt operation or
installation without a proper knowledge on how to do so.
This fixture was designed for indoor use only; use of this fixture outside will void the
manufacture’s warranty.
Consistent operational breaks will ensure that the fixture will function properly for many
years to come.
Do not shake the fixture around. Avoid brute force when installing or operating the fixture.
While choosing an installation location, please be sure that the fixture will not be exposed to
extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat
surface should be at least 0.5 meter (about 1.5ft). See page 11.
Always install the fixture with an appropriately rated safety cable. When installing the fixture
in a suspended environment always be sure to use mounting hardware no less than M10 x
25 mm, also be sure the hardware is only inserted in the yoke’s mounting holes.
Do not attempt to operate this fixture until you have familiarized yourself with all of its
functions.
Do not permit operation by persons not qualified for operating this type of architectural
fixture. Most damages are the result of improper operation.
Please use the original packaging to transport the fixture in for service.
For your own safety, please read this user manual carefully before installing the device.
©Elation Professional, Los Angeles Ca.
8
DESIGN LED 36 Pro™
5. FIXTURE OVERVIEW
1. LED Lens Assembly – The lens assembly may be user replaced in the event repair
is needed or a different beam angle is required.
©Elation Professional, Los Angeles Ca.
9
DESIGN LED 36 Pro™
2. LED Display – 4-segment menu display. Used to display the DMX address as well
as all other menu functions.
3. Power Output Lead – This lead is used to jump power to another Design LED 36
Pro™. Please do not daisy-chain power for more than 16 fixtures.
4. DMX Out Lead – XLR female lead. This lead is used to send an incoming DMX
signal to the next fixture in the DMX chain.
5. Menu Button – This button is used to access the fixtures menu functions.
6. Up Button – The up button is used to toggle forward through the menu functions and
settings.
7. Down Button – The down button is used to toggle backwards through the menu
functions and settings.
8. Enter Button – The enter button is used to enter in to a certain menu function or to
lock a menu setting in to memory.
9. Yoke Assembly – This yoke is designed to perform two functions; 1) When split it
can be used as a floor stand bracket. 2) Used to secure a mounting clamp for truss
mounting.
10. Main Power Input Lead – This lead is the main power input lead.
11.DMX In Lead – XLR male lead. This lead is the main DMX input lead.
6. MOUNTING AND INSTALLATION
Cautions:
©Elation Professional, Los Angeles Ca.
10
DESIGN LED 36 Pro™
For added protection mount the fixtures in areas outside walking paths, seating areas, and
away from areas were unauthorized personnel might reach the fixture.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’s weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
To avoid injury, never stand directly below the device when mounting, removing, or servicing
the fixture.
Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE0711-217
for proper installation in Europe To ensure proper installation, only
qualified staff should attempt installation.
Mounting points
Overhead mounting requires extensive experience, including amongst others calculating
working load limits, a fine knowledge of the installation material being used, and periodic
safety inspection of all installation material and the fixture. If you lack these qualifications, do
not attempt the installation yourself. Improper installation can result in bodily injury.
CAUTION!
Be sure a qualified electrician performs all electrical
connections.
Be sure to complete all rigging and installation procedures before connecting the main
power cord to the appropriate wall outlet.
©Elation Professional, Los Angeles Ca.
11
DESIGN LED 36 Pro™
Mounting
The Design LED 36 Pro™ is fully operational in any mounting position, hanging
upside-down, side mounted, or set on a flat level surface, etc. Be sure this fixture is kept at
least 0.5m (1.5 feet) away from any flammable materials (decoration etc.). When clamp
mounting; always use and install the supplied safety cable as an added safety measure to
prevent accidental damage in the event of a clamp failure. See the image below.
Clamp Mounting
The Design LED 36 Pro™ provides a unique mounting bracket assembly that allows the unit
to stand on a flat surface or to be hung on truss via a clamp in any safe position (see the
illustration above). Regardless of the mounting option you choose please be sure to refer to
the safety guidelines in this manual to avoid damage to the unit and/or personal injury.
When mounting this fixture to truss be sure to secure an appropriately rated clamp to the
hanging yoke using a M10 screw fitted through the center hole of the hanging yoke. As an
©Elation Professional, Los Angeles Ca.
12
DESIGN LED 36 Pro™
added safety measure be sure to attach at least one properly rated safety cable to the fixture.
See illustrations below.
Securing the Design LED 36 Pro™
Always be sure to secure your fixture with a safety cable when
suspending the unit from truss or other means. The fixture
provides a built-in rigging point for a safety cable as illustrated
above. Be sure to only use the designated rigging point for the
safety cable and never secure a safety cable to the hanging
bracket.
©Elation Professional, Los Angeles Ca.
13
DESIGN LED 36 Pro™
7. UNDERSTANDING DMX
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most
lighting and controller manufactures as a form of communication between intelligent fixtures
and controllers. DMX allows all makes and models of different manufactures to be linked
together and operate from a single controller. This is possible as long as all the fixtures and
the controller are DMX compliant. A DMX controller sends the DMX data instructions to a
fixture allowing the user to control the different aspects of an intelligent light. DMX data is
sent out as serial data that travels from fixture to fixture via data “IN” and “OUT” leads
located on the fixtures (most controllers will only have output jacks).
DMX Linking: To ensure proper DMX data transmission, always use proper DMX cables
and a terminator. When using several DMX fixtures try to use the shortest cable path
possible. Never split a DMX line with a “Y” style connector. The order in which the fixtures
are connected in a DMX line does not influence the DMX addressing. For example; a fixture
assigned a DMX address of 1 may be placed anywhere in the DMX chain, at the beginning,
at the end, or anywhere in the middle. The DMX controller knows to send data assigned to
address 1 to that fixture no matter where it is located in the DMX chain. The Design LED 36
Pro™ can be controlled via DMX-512 protocol. The Design LED 36 Pro™ is a fixture that
can operate in 3, 4, or 6 DMX channels (see page 21 for the different DMX traits). The DMX
address is set electronically using the controls on the LED menu.
You can chain multiple fixtures together through serial linking. Using the IP rated signal
cables provided through Elation. Always be sure to daisy-chain your in and out data
connections, never split or “Y” your DMX connections unless you are using an approved
DMX splitter such as the Elation Opto Branch 4™ or DMX Branch/4™.
©Elation Professional, Los Angeles Ca.
14
DESIGN LED 36 Pro™
DMX-512 connection with DMX terminator
A DMX terminator should be used in all DMX lines especially in longer runs. The use of a
terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt
resistor that is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA
-). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain
to terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease the
possibilities of erratic behavior.
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA
transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX
line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must
be used, these adaptors are readily available at most electric stores. The following chart
details a proper cable conversion.
Fixture DMX addressing;
All fixtures should be given a DMX starting address when using a DMX controller, so the
©Elation Professional, Los Angeles Ca.
15
DESIGN LED 36 Pro™
correct fixture responds to the correct control signal. This digital starting address is the
channel number from which the fixture starts to “listen” to the digital control information sent
out from the DMX controller. The allocation of this starting DMX address is achieved by
setting the correct DMX address on the digital display located on the back of the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set different
address for each individual fixture. Be advised that setting all you fixtures to the same DMX
address will subsequently control all fixtures in the same fashion, in other words, changing
the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the
channel number you have set, based on the quantity of control channels (DMX channels) of
each fixture. That means changing the settings of one channel will only affect the selected
fixture.
In the case of the Design LED 36 Pro™, which is up to a six channel fixture (default may also
be set to three or four channels), you should set the starting DMX address of the first unit to
1, the second unit to 4 (3 + 1), the third unit to 7 (3 + 4), and so on.
Note: During start-up the Design LED 36 Pro™ will automatically detect whether a DMX
data signal is being received or not. If a DMX data signal is being received, the display will
show "A.XXX" (XXX representing the actual DMX address). If the fixture is not receiving a
DMX signal the display will flash "A.XXX" (XXX representing the actual DMX address).
If your fixture is connected to a DMX controller and the display is flashing (not receiving a
DMX signal), please check the following:
-
The 3-pin or 5-pin XLR plug (cable with DMX signal from controller) may not be
connected or is not inserted completely into the DMX input jack.
The DMX controller is switched off or defective.
-
-
-
The DMX cable or connector is defective.
A DMX terminator has been inserted into the last fixture in your DMX chain.
©Elation Professional, Los Angeles Ca.
16
DESIGN LED 36 Pro™
8. DISPLAY LED INDICATORS.
The Design LED 36 Pro ™ has two LED indicators on the display. These indicators are
designed to give a quick visual indication of the fixtures’ status. The illustration below details
the functionality of the LED indicators.
. .
.
.
DMX OK
NO DMX
DMX OK
Lamp off
NO DMX
Lamp off
Lamp on
Lamp on
The first LED indicators represents DMX signal:
• If the indicators is on a clean DMX signal is present
• If the indicator is off there is no DMX signal present
The second LED indicator represents lamp condition; this is only applicable to fixtures with
traditional lamp sources.
©Elation Professional, Los Angeles Ca.
17
DESIGN LED 36 Pro™
9. DISPLAY MENU
Default settings shaded.
Set the starting DMX address
ADDR
AXXX (1-512)
Display “Blackout” function. When activated the
display will automatically blackout when not in use.
When “ON” this function rotate the display 180˚
DISP
FLIP
ON/OFF
ON/OFF
3 CH
3 DMX CHANNELS (RGB)
CHAN
4 CH
6 CH
4 DMX CHANNELS (RGB+MASTER DIM)
6 DMX CHANNELS
SLAV
CNTL
BLAC
ON/OFF
UNIT FUNCTIONS AS SLAVE
Fixture will function as a master unit in Master/Slave
mode
MAST
ALON
Fixture will function “Stand Alone” mode
BLACKOUT – LED OUTPUT OFF
Manual Mode - Manual setting of RED levels
RED
RXXX
GXXX
BXXX
SXXX
XXX
Manual Mode - Manual setting of GREEN levels
Manual Mode - Manual setting of BLUE levels
Manual Mode - Manual setting of STROBE rate
GREN
BLUE
STRB
SPED
FADE
STRB
SPED
FADE
STRB
SPED
FADE
COLR
Adjust program 1 speed
CHS1
CHS2
XXX
Adjust program 1 fade time
Adjust strobe rate of program 1
Adjust program 2 speed
XXX
XXX
XXX
Adjust program 2 fade time
Adjust strobe rate of program 2
Adjust program 3 speed
XXX
XXX
CHS3
CHS4
XXX
Adjust program 3 fade time
STRB
SPED
XXX
XXX
Adjust strobe rate of program 3
Adjust program 4 speed
©Elation Professional, Los Angeles Ca.
18
DESIGN LED 36 Pro™
FADE
STRB
SPED
FADE
STRB
SPED
FADE
STRB
SPED
FADE
STRB
SPED
FADE
STRB
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
XXX
Adjust program 4 fade time
Adjust strobe rate of program 4
Adjust program 5 speed
CHS5
CHS6
CHS7
Adjust program 5 fade time
Adjust strobe rate of program 5
Adjust program 6 speed
Adjust program 6 fade time
Adjust strobe rate of program 6
Adjust program 7 speed
Adjust program 7 fade time
Adjust strobe rate of program 7
Adjust program 8 speed
CHS8
DIMR
Adjust program 8 fade time
Adjust strobe rate of program 8
Standard - Fixture will function with a stepping
dimmer rate
MOD1
Linear - Fixture will function with a dimming rate of
0~100%
MOD2
LODA
VER
Reset to Fixture to the Factory Default Settings
“X.X’ will represent the fixture’s current firmware
version
V X.X
Note:
1) If the fixture does not receive a DMX signal the menu display will flash repeatedly.
2) SPED: Adjust the hold time for each scene in built-in chase programs.
3) FADE: Adjust the fade time between each scene in the built-in programs.
©Elation Professional, Los Angeles Ca.
19
DESIGN LED 36 Pro™
10.DMX TRAITS
DMX Operation Notes:
The fixture will function in DMX mode whenever the unit is receiving a DMX signal. Please
note that this will override all manual settings.
This unit will keep and retain the last DMX command in the event of DMX signal failure. To
reset the fixture you must turn the power off.
DMX CHANNEL TRAITS
The charts below and on the preceding pages outline the different DMX traits for the three
different DMX modes.
3-Channel mode: In this mode channel one controls all the red LEDs, channel two controls
all the green LEDs, and channels three controls all the blue LEDs. 3-Channel Mode: The
chart below details the DMX channel layout for 3-channel assignment.
©Elation Professional, Los Angeles Ca.
20
DESIGN LED 36 Pro™
DMX channel’s functions and their values (3-Channel Mode):
Channel 1 - Red:
0-255
Red (0-Black, 255 - 100% Red)
Channel 2 - Green:
0-255
Green (0-Black, 255 - 100% Green)
Channel 3 - Blue:
0-255
Blue (0-Black, 255 - 100% Blue)
4-Channel mode: In this mode channel one controls all the red LEDs, channel two controls
all the green LEDs, channels three controls all the blue LEDs, and channel four-- will control
the master dimming level. 4-Channel Mode: The chart below details the DMX channel layout
for 4-channel assignment.
©Elation Professional, Los Angeles Ca.
21
DESIGN LED 36 Pro™
DMX channel’s functions and their values (4-Channel Mode):
Channel 1 - Red:
0-255
Red (0-Black, 255 - 100% Red)
Channel 2 - Green:
0-255
Green (0-Black, 255 - 100% Green)
Channel 3 - Blue:
0-255
Blue (0-Black, 255 - 100% Blue)
Channel 4 - Dimming / Program Speed Control
This channel has two functions depending on the operating mode. When running the built-in
programs this channel will control the program speed.
0-255
0-255
Dimming (0%-100%) ~ Normal Operation
Speed (min to max) ~ When running built-in programs on channel 4
6-Channel mode: In this mode channels 1~3 are used to control the RGB LEDs and
channels 4~6 will control special features. 6-Channel Mode: The charts below and on the
next page detail the DMX channel layout for 6-channel assignment.
©Elation Professional, Los Angeles Ca.
22
DESIGN LED 36 Pro™
DMX channel’s functions and their values (6-Channel Mode):
Channel 1 - Red:
0-255
Red (0-Black, 255-100% Red)
Channel 2 - Green:
0-255
Green (0-Black, 255- 100% Green)
Channel 3 - Blue:
0-255
Blue (0-Black, 255- 100% Blue)
Channel 4 - Internal programs:
0-10
No function
11-40
41-70
71-100
Internal program 1
Internal program 2
Internal program 3
101-130 Internal program 4
131-160 Internal program 5
161-190 Internal program 6
191-220 Internal program 7
221-255 Internal program 8
Channel 5 - Strobe:
0
No function
1~95
96-127
Strobe effect slow to fast
No function
128-159 Pulse effect in sequences
160-191 No function
192-223 Random strobe effect slow to fast
224-255 No function
©Elation Professional, Los Angeles Ca.
23
DESIGN LED 36 Pro™
Channel 6 - General dimming / Program Speed Control
This channel has two functions depending on the operating mode. When running the built-in
programs this channel will control the program speed, when not running the built-in programs
this channel will control master dimming.
0-255
0-255
Dimming (0%-100%) ~ Normal Operation
Speed (min to max) ~ When running built-in programs on channel 4
©Elation Professional, Los Angeles Ca.
24
DESIGN LED 36 Pro™
11. LENS REPLACEMENT
The Design LED 36 Pro comes with a removable front cover that allows the lens assembly to
be changed out to achieve different beam angles.
The lens cover is held in place by four 5mm Allen screws. To access the lens kit, remove the
bard door assembly (if so attached) to access the four 5mm Allen screws, then loosen the
screws. The screws are held in by clips so they cannot be removed completely. Lift the outer
cover to access the lens kit. The lens kit is held in by four Phillips screws, remove these
screws to remove the lens kit. Replace the lens kit with the preferred option and reassemble
in reverse order. Be sure to align the rubber seal properly when reassembling.
©Elation Professional, Los Angeles Ca.
25
DESIGN LED 36 Pro™
12. CLEANING AND MAINTENANCE
Consider the following points during normal service and inspection:
1. Be sure all screws and fasteners are securely tightened at all times. Lose screws may
fall out during normal operation resulting in damage or injury as larger parts could fall.
2. Electric power supply cables must not show any damage, material fatigue or
sediments. Never remove the ground prong from the power cable.
Further instructions depending on the installation spot and usage have to be adhered by a
skilled installer and any safety problems have to be removed.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never
use alcohol or solvents.
There are no user serviceable parts inside this fixture, please refer all other service issues to
an authorized Elation service technician.
Should you need any spare parts, please order genuine parts from your local dealer.
©Elation Professional, Los Angeles Ca.
26
DESIGN LED 36 Pro™
13.
2-YEAR LIMITED WARRANTY
A. Elation Professional® hereby warrants, to the original purchaser, Elation Professional®
products to be free of manufacturing defects in material and workmanship for a period of two
years, (730 days) from the date of purchase. This warranty shall be valid only if the product
is purchased within the United States of America, including possessions and territories. It is
the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service, send the product only to the Elation Professional® factory. All
shipping charges must be pre-paid. If the requested repairs or service (including parts
replacement) are within the terms of this warranty, Elation Professional® will pay return
shipping charges only to a designated point within the United States. If the entire instrument
is sent, it must be shipped in its original package. No accessories should be shipped with the
product. If any accessories are shipped with the product, Elation Professional® shall have no
liability what so ever for loss of or damage to any such accessories, nor for the safe return
thereof.
C.
This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which Elation Professional® concludes, after inspection, affects the
reliability of the product; if the product has been repaired or serviced by anyone other than
the Elation Professional® factory unless prior written authorization was issued to purchaser
by Elation Professional®; if the product is damaged because not properly maintained as set
forth in the instruction manual.
D. This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, Elation Professional® will replace
defective parts at its expense, and will absorb all expenses for warranty service and repair
labor by reason of defects in material or workmanship. The sole responsibility of Elation
Professional® under this warranty shall be limited to the repair of the product, or replacement
thereof, including parts, at the sole discretion of Elation Professional®. All products covered
by this warranty were manufactured after January 1, 1990, and bare identifying marks to that
©Elation Professional, Los Angeles Ca.
27
DESIGN LED 36 Pro™
effect.
E. Elation Professional® reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products
theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by
applicable law, all implied warranties made by Elation Professional® in connection with this
product, including warranties of merchantability or fitness, are limited in duration to the
warranty period set forth above. And no warranties, whether expressed or implied, including
warranties of merchantability or fitness, shall apply to this product after said period has
expired. The consumer’s and or Dealer’s sole remedy shall be such repair or replacement as
is expressly provided above; and under no circumstances shall Elation Professional® be
liable for any loss or damage, direct or consequential, arising out of the use of, or inability to
use, this product.
G. This warranty is the only written warranty applicable to Elation Professional® Products
and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
©Elation Professional, Los Angeles Ca.
28
DESIGN LED 36 Pro™
14.
PHOTOMETRIC DATA
©Elation Professional, Los Angeles Ca.
29
DESIGN LED 36 Pro™
15.
DIMENSIONAL DRAWINGS
©Elation Professional, Los Angeles Ca.
32
DESIGN LED 36 Pro™
16.
CIRCUIT SCHEMATIC
©Elation Professional, Los Angeles Ca.
33
DESIGN LED 36 Pro™
17.
TECHNICAL SPECIFICATIONS
Power supply:
100v~240v / 50Hz~60Hz AC
Maximum 150w
Power consumption:
LED Configuration:
36 x 3 Watt
(12 x Red, 12 x Green 12 x Blue)
6 Kgs / 15.2Lbs
Weight:
DMX Channels:
DMX Drive:
6, 4, or 3 Channel mode
Standard DMX-512,
3-Pin XLR; [+] = Pin 3 [-] = Pin 2 [Ground] = Pin 1.
RGB Color Additive Mixing
Color Mixing:
Beam Angle:
Fuse:
30˚ (25˚ Lens) / Optional 15˚ & 45˚ Lenses
GMA 220v~2A (Internal)
Dimmer:
Continuous Dimming 0~100%
Electronic Strobe 0~18 Fps
100,000 Hours Rated Life
Strobe:
Lamp Life:
Dimensions:
(232 x 220 x 260) mm
9.13” x 8.66” 10.24”
Please Note: Specifications and improvements in the design of this unit and this manual are
subject to change without any prior written notice.
©Elation Professional, Los Angeles Ca.
34
Elation Professional
6122 S. Eastern Ave.
Los Angeles, CA. 90040
323-582-3322 / 323-832-9142 fax
Rev. 5/13/2009 - visage
|