Dual XDM6220 User Manual

XDM6220  
INSTALLATION/OWNER'S MANUAL  
AM/FM/CD/MP3/WMA Receiver with Detach Face  
XDM6220 INSTALLATION  
Wiring Diagram  
FUSE  
When replacing the fuse,  
make sure new fuse is the  
correct type and amperage.  
Using an incorrect fuse  
could damage the radio. The  
XDM6220 uses one 10 amp  
AGC fuse (Battery) located  
in-line.  
3
XDM6220 OPERATION  
Control Locations  
3
4
7
8
1
2
5
6
21  
20  
19  
18  
17  
16  
15  
14  
13  
12  
11  
10  
9
Release  
Power  
Mute  
EQ/9  
Tuner Scan/8  
Local/Distance/7  
1
2
3
4
5
6
7
8
9
12  
13  
14  
15  
16  
17  
18  
19  
Audio  
Preset 6/Folder Up  
Preset 5/Folder Down  
Preset 4  
Band/Play/Pause  
Auto Store/Preset Scan/Enter  
Mode/Search  
Preset 3/Intro  
Eject  
Preset 2/Random  
Tune/Track Up/Down  
Loudness  
20 Preset 1/Repeat  
21  
10  
11  
Volume Up/Down  
Display/0  
The XDM6220 allows playback of your favorite MP3 and WMA files recorded on CD-R and  
CD-RW discs. Its powerful on-board DSP processor decodes the compressed audio while  
maintaining near-CD sound quality. An internal SRAM buffer provides ESP (Electronic  
Skip Protection) to virtually eliminate skipping and allows alphanumeric or direct track  
search - even while a song is currently playing!  
4
XDM6220 OPERATION  
General Operation  
Faceplate Removal Press RELEASE and pull away from the left side to remove.  
To re-install, insert right side of faceplate first then push  
left side to secure.  
Semi-permanent Remove trim ring and install supplied #1 x 7/32” Phillips  
Faceplate Installation head screw through left side of mounting frame into faceplate.  
Power On/Off Press PWR or any other button (except eject or volume up/  
down) to turn the unit on. Inserting a disc will turn the unit  
on automatically. Press PWR to turn the unit off.  
Mode Press MODE to select between tuner, CD player and auxiliary  
input. Modes of operation are indicated in the display.  
Loudness Press LOUD to activate and deactivate the loudness contour  
curve. Activating this feature will enhance the bass and  
treble frequencies when listening to music at low volumes.  
Volume Adjust volume using VOL t / VOL s (00-46).  
Programmable Press and hold PWR for 3 seconds to program currently  
Turn-On Volume selected volume level. "P-VOL" and the current volume level  
will momentarily appear in the display.  
Preset EQ Curves Press EQ to select between POP, JAZZ, CLASSIC, BEAT,  
ROCK and OFF (default) equalization curves. Any adjustment  
to the Bass or Treble settings automatically cancels the  
current EQ curve (if one is selected).  
Display Press DISP to select between clock and radio frequency  
(tuner mode), clock and CD track/elapsed time (CD mode),  
or clock and AUX (AUX mode).  
Set the Clock With the unit on, press and hold DISP until the clock begins  
to flash, then release. Press TUNE << to adjust the hours  
and TUNE >> to adjust the minutes. Press DISP momentarily  
to save the selected time.  
12/24-hour Clock The clock will display 12-hour AM/PM time in USA frequency  
:
spacing mode (PM 10 00). In European frequency spacing  
mode, the clock will display 24-hour time (22:00).  
5
XDM6220 OPERATION  
General Operation  
Programmable Display In tuner mode, press and hold DISP then press TUNE >>  
Priority to select function priority display. “FREQ” will momentarily  
appear in the display.  
Note:  
"FUNC" will appear in CD or AUX modes.  
Radio frequency (tuner mode), CD track/elapsed time (CD  
mode) or AUX (AUX mode) will be displayed by default.  
Note:  
When playing MP3/WMA files, the track number/elapsed  
time, track name, directory name, title, artist, album, year  
or comment will be displayed by default. Clock is accessed  
by pressing DISP momentarily.  
Press and hold DISP then press TUNE << to select time  
display priority. “TIME” will momentarily appear in the  
display. Clock will be displayed by default. Radio frequency,  
CD track/elapsed time or MP3/WMA file information is  
accessed by pressing DISP momentarily.  
Programmable Clock Programs unit to display clock/no clock when unit is off.  
Priority Press and hold MODE then press PRESET 1 to select clock  
priority on/off. “CLK ON” or “CLK OFF” will momentarily  
appear in the display.  
Reset Press and hold for more than 2 seconds to RESET the unit  
upon initial installation or if abnormal operation occurs.  
The reset button is located behind the faceplate. Refer to  
page 2 for details.  
Confirmation Beep Press and hold AUD for 3 seconds to turn confirmation  
beep on/off. "BEEP ON" or BEEP OFF" will momentarily  
appear in the display.  
Mute Press MUTE to silence the audio. “MUTE” will flash in the  
display. Press MUTE again to cancel.  
6
XDM6220 OPERATION  
General Operation  
Audio  
Press AUD to select between Volume (default), Bass, Treble,  
Balance & Fader.  
Bass  
Treble  
Press AUD until BAS appears  
Press VOL t or s to adjust  
( -6 minimum / +6 maximum)  
Press AUD until TRE appears  
Press VOL t or s to adjust  
( -6 minimum / +6 maximum)  
Balance  
Press AUD until BAL appears  
Press VOL t or s to adjust  
(BAL L 12-BAL 00-BAL R 12)  
BAL 00 represents equal balance  
Fader  
Press AUD until FAD appears  
Press VOL t or s to adjust  
(FAD F 12-FAD 00-FAD R 12)  
FAD 00 represents equal fader  
Source Audio Memory  
Individual Bass and Treble settings are retained in memory  
for AM, FM, CD, and AUX modes. This allows you to save  
the Bass and Treble settings separately for each mode.  
Example:  
FM tuner mode can have Bass +3 and Treble -1 while CD  
mode can have Bass +2 and Treble +2.  
Note:  
Any adjustment to the Bass or Treble settings automatically  
cancels the current EQ curve (if one is selected).  
7
XDM6220 OPERATION  
Tuner Operation  
Press TUNE << or TUNE >> momentarily to seek the next  
strong station.  
Seek Tuning  
Press TUNE << or TUNE >> for more than 2 seconds, then  
release. "MANUAL" will momentarily appear in the display.  
Press TUNE << or TUNE >> momentarily to move radio  
frequency up or down one step at a time. Press and hold to  
advance quickly. If tuning is not adjusted for 5 seconds, the  
unit will return to seek tuning mode (default). "AUTO" will  
momentarily appear in the display.  
Manual Tuning  
Press SCAN to preview strong stations on the current band,  
Scan Tuning  
pausing for 5 seconds at each. Press SCAN again to cancel.  
Press LOC to activate local tuning for strong station reception  
only. Press LOC again to cancel and resume distance tuning  
(default).  
Local/Distance  
Press BAND to select between FM1, FM2, FM3, AM1 and AM2  
Band  
bands.  
Press and hold BAND then press TUNE << to select  
European frequency spacing. Press and hold BAND then  
press TUNE >> to select USA frequency spacing (default).  
Frequency Spacing  
Up to 18 FM stations and 12 AM stations can be stored. To  
store a station, select the desired band and station. Press  
and hold the desired preset button (1-6) for more than  
2 seconds. When stored, the preset number will appear in  
the display. The station can be recalled anytime by pressing  
the corresponding preset button.  
Storing and Recalling  
Station Presets  
Note:  
Function buttons 7, 8, 9 and 0 apply to MP3 and WMA  
playback only.  
Press AS/PS for more than 2 seconds to automatically store  
the six strongest stations in the current band. Automatic  
Local/Distance is activated during the initial band scan.  
Automatically Store  
Stations  
Press AS/PS for less than 2 seconds to scan presets 1-6 on  
the current band, pausing for 5 seconds at each. Press  
AS/PS again to cancel.  
Preset Scan  
8
XDM6220 OPERATION  
CD Player Operation  
With the label facing up, insert a standard size CD into the  
CD slot. The CD will automatically begin playback.  
Insert CD  
Eject CD  
Press EJECT to eject the CD. The unit will change to previous  
mode of operation (AM, FM, or auxiliary input). If the disc is  
not removed within 10 seconds, the unit will reload the disc.  
The unit does not have to be turned on to eject CD.  
Press TRACK >> to skip to the beginning of the next track.  
Press TRACK << to return to the beginning of the current  
track. Pressing TRACK << again skips to the beginning of  
the previous track.  
Track Select  
Press and hold TRACK >> or TRACK << to fast forward or  
reverse a track.  
Fast Forward and Reverse  
Press  
Press  
/
/
II to temporarily stop CD playback.  
II again to resume playback.  
Pause  
Intro  
l
l
Press INT to play the first 10 seconds of each track.  
Press INT again to cancel.  
Press RPT to continuously repeat selected track.  
Press RPT again to cancel.  
Repeat  
Random  
Press RDM to play all tracks in random order. Press RDM  
again to cancel. Random mode is retained in memory when  
selecting between tuner, CD player and auxiliary input  
modes and when the unit is turned on/off.  
Some CD-Rs and CD-RWs may be incompatible with this  
unit, depending on media type and recording method. In  
addition, the following CDs may be incompatible with this  
unit:  
CD-R/CD-RW Compatibility  
CDs exposed to extreme temperatures or direct sunlight for  
extended periods of time, CDs recorded in which a recording  
session failed or a re-recording was attempted and, or  
encrypted or copy-protected CDs which do not conform to  
the audio CD-DA red book recording standard.  
9
XDM6220 OPERATION  
CD Player Operation - MP3/WMA Files  
When an MP3/WMA encoded disc is first inserted,  
Playing an MP3/WMA Disc  
“READING” will appear in the display. Depending on the  
number of files and folders, this may take several seconds.  
The  
icon will illuminate anytime a valid MP3 encoded  
MP3 Icon  
WMA Icon  
disc is inserted and flash in MP3 search/navigate modes.  
The  
icon will illuminate anytime a valid WMA encoded  
disc is inserted and flash in WMA search/navigate modes.  
Folder Icon  
The  
icon will illuminate anytime a folder is selected in  
the file/folder search modes.  
Displaying Information  
Press DISP to select between track number/elapsed time  
(default), clock, track name, directory name, title, artist,  
album, year and comment.  
“NO ID3 TAG” will be displayed if the MP3 file contains no  
ID3 tag information.  
“UNKNOWN” will be displayed if the WMA file contains no  
WMA tag information.  
“ROOT” will be displayed if the directory name of a root  
folder is not labeled.  
Character Support  
Maximum character display information  
• Track name – 32 character maximum  
• Directory name – 32 character maximum  
• *Song title – 30 character maximum  
• *Artist name – 30 character maximum  
• *Album name – 30 character maximum  
• *Year – 4 character maximum  
• *Comment – 28 character maximum  
*Song title, Artist Name, Album name, Year and Comment  
will only be displayed if included with the MP3/WMA file.  
When referring to MP3/WMA playback, the following terms  
are synonymous:  
• File name and track name  
• Folder name and directory name  
10  
XDM6220 OPERATION  
CD Player Operation - MP3/WMA Files  
Refer to the following button function table when selecting, searching or  
navigating MP3/WMA files and folders:  
MP3/WMA Button Function Table  
Button  
Function  
SEARCH  
Direct Select, Search and Navigate Modes  
Enter/Confirm  
A, B, C, 1  
Preset 1  
Preset 2  
D, E, F, 2  
Preset 3  
G, H, I, 3  
Preset 4  
J, K, L, 4  
Preset 5  
M, N, O, 5  
Preset 6  
P, Q, R, 6  
7
S, T, U, 7  
8
V, W, X, 8  
9
Y, Z, /, 9  
0
AUD  
-, _, +, 0  
Character Shift  
Character Select (A, B, C ~ 8, 9, 0)  
Character Backspace  
VOL t / VOL s  
MUTE  
Direct Select, Search and  
Navigate Modes  
Press SEARCH for more than 3 seconds, to select between  
the following modes:  
• Direct File Select  
• Alphanumeric File or Folder Search  
• File or Folder Navigate  
Direct File Select  
Step 1  
Press SEARCH for more than 3 seconds, then release.  
“MP3 T " or “WMA T ” will flash in the display. Use the  
*
*
buttons in the above table (3 keystroke maximum input),  
or the VOL t / VOL s to enter the desired file number.  
Step 2  
Press  
to confirm the selected file number or wait for  
the input cycle to time out (approximately 5 seconds).  
If the file is not available, “NO FILE” will be displayed  
momentarily and the current file will continue to play.  
11  
XDM6220 OPERATION  
CD Player Operation - MP3/WMA Files  
Alphanumeric File  
or Folder Search  
Step 1  
Press SEARCH for more than 3 seconds, then release.  
Press SEARCH again, an " " will flash in the display. Use  
*
the buttons in the table on page 11 (32 character maximum  
input) or the VOL t / VOL s to enter the desired alphanu-  
meric search characters. Press AUD to advance one  
character to the right.  
Step 2  
Step 3  
Press  
to initiate the selected alphanumeric search.  
Press VOL t / VOL s to preview the search results.  
If the search returns a folder, the icon will illuminate.  
Step 4  
Step 5  
Press  
to select the desired file or folder. If a folder  
is selected, two "/ /" will illuminate. Press VOL s to begin  
searching files in the folder.  
Press  
Note:  
to select the desired file within the folder.  
If the file is not available, “NO FILE” will be displayed  
momentarily and the current file will continue to play.  
File/Folder Navigate  
Step 1  
Press SEARCH for more than 3 seconds, then release.  
Press SEARCH again two times to navigate files/folders  
on the disc. The current folder name will scroll one time  
followed by available files and folders.  
Step 2  
Step 3  
Step 4  
Press VOL t / VOL s to preview files/folders in the  
current folder. If a folder is selected, the  
illuminate.  
icon will  
Press  
to select the desired file or folder. If a folder  
is selected, two "/ / " will illuminate. Press VOL s to begin  
searching files in the folder.  
Press  
to select the desired file within the folder.  
*Folder Access  
(Up one level)  
When navigating root folders “/ /“ will illuminate. Press  
AUD to access the previous folder level (up one level).  
*Only available on MP3/WMA discs recorded with more  
than one folder.  
12  
XDM6220 OPERATION  
CD Player Operation - MP3/WMA Files  
*Folder Access Press F  
to select the previous folder.  
to select the next folder.  
Press F  
*Folder access is only available on MP3/WMA discs recorded  
with more than one folder.  
File Repeat Press RPT momentarily to continuously repeat selected file.  
Press RPT again to cancel.  
File Repeat Press RPT for more than 2 seconds to consecutively repeat  
(Current Folder Only) all files in the current folder only. The  
the display when in folder repeat mode.  
Press RPT again to cancel.  
icon will appear in  
Disc Random Press RDM momentarily to play all files on entire disc in  
random order. Press RDM again to cancel.  
Folder Random Press RDM for more than 2 seconds to play all files in  
current folder only in random order. The  
in the display when in folder random mode.  
Press RDM again to cancel.  
icon will appear  
Disc Intro Press INT momentarily to play the first 10 seconds of each  
file on the entire MP3/WMA disc. Press INT again to cancel.  
Folder Intro Press INT for more than 2 seconds to play the first 10  
seconds of each file in the current folder only. The  
will appear in the display when in folder intro mode.  
Press INT again to cancel.  
icon  
Note:  
File repeat (current folder only), folder random and folder  
intro is only available on MP3/WMA discs recorded with  
more than one folder.  
13  
XDM6220 OPERATION  
CD Player Operation - MP3/WMA Files  
Media Compatibility The following types of discs/files are compatible:  
• CD-ROM (ISO), CD-R, CD-RW  
• CD-DA  
• MP3 data  
• WMA data  
The following types of discs/files are not compatible:  
• WMA files that are protected by DRM (Digital Rights  
Management).  
• WMA lossless format  
• Discs recorded with Track At Once or packet writing  
• MP3 PRO format  
• MP3 playlists  
• WAV format  
Playback Order MP3/WMA playback sequence is based on recorded order of  
files and begins in the root folder of the disc. Any empty  
folders or folders that do not include MP3/WMA files are  
skipped. This unit may not play files in the order they were  
recorded in. Refer to your recording software’s user’s manual  
for more information.  
Compatible Recording • ISO9660 level 1  
Formats • ISO9660 level 2  
• Yellow Book MODE 1  
• Yellow Book MODE 2 FORM 1  
• Multi session  
• Maximum folders and files - 256  
• Maximum folder levels - 8  
• MPEG-1/2/2.5 Audio Layer-3  
ISO9660 standards:  
• Maximum nested folder depth is 8 (including the root folder).  
• Valid characters for folder/file names are letters A-Z  
(all caps), numbers 0-9, and “_” (underscore). Some  
characters may not be displayed correctly, depending on  
the character type.  
• This device can play back discs in Joliet, Romeo, and other  
standards that conform to ISO9660. MP3/WMA written in the  
formats other than the above may not play and/or their file  
names or folder names may not be displayed properly.  
14  
XDM6220 OPERATION  
CD Player Operation - MP3/WMA Files  
Additional MP3/WMA An internal buffer provides ESP (Electronic Skip Protection)  
Information to virtually eliminate skipping.  
When playing a disc recorded with regular audio files  
(CD-DA or .WAV) and MP3/WMA files, the unit will play the  
MP3/WMA files only.  
Only MP3 files with filename extension (.mp3) can be played.  
Only WMA files with filename extension (.wma) can be played.  
Do not attempt to play discs which contain non-MP3/WMA  
files with the MP3/WMA extension.  
Sampling Frequency Rates  
MP3 8kHz ~ 48kHz  
WMA 32kHz ~ 48kHz  
Transfer Bit rates  
MP3 8kbps ~ 320kbps constant  
Variable bit rates  
WMA 32kbps ~ 192kbps constant  
Variable bit rates  
Note:  
Some files may not play or be displayed correctly,  
depending on sampling rates and bit rates.  
MP3 Tag Display ID3 tags Version 1.x  
This model will not display ID3 Version 2.0 or greater tags.  
Recommended Settings For best results, use the following settings when burning an  
MP3 disc:  
128kbps or higher constant bit rate  
44.1kHz or higher sampling frequency  
For best results, use the following settings when burning a  
WMA disc:  
64kbps or higher constant bit rate  
32kHz or higher sampling frequency  
15  
XDM6220 WARRANTY  
Limited One-Year Warranty  
This warranty gives you specific legal rights.  
You may also have other rights which vary from  
state to state.  
What to do?  
1. Before you call for service, check the  
troubleshooting guide in your owner’s  
manual. A slight adjustment of any custom  
controls or connections discussed in your  
instruction booklet may save you a service  
call.  
Dual Electronics Corp. warrants this product to  
the original purchaser to be free from defects in  
material and workmanship for a period of one  
year from the date of the original purchase.  
2. If you require service during the warranty  
period, you must carefully pack the product  
(preferably in the original package) and ship  
it by prepaid transportation with a copy of the  
original receipt from the retailer to an  
authorized service center.  
Dual Electronics Corp. agrees, at our option,  
during the warranty period, to repair any defect  
in material or workmanship or to furnish an  
equal new, renewed or comparable product  
(whichever is deemed necessary) in exchange  
without charges, subject to verification of the  
defect or malfunction and proof of the date of  
purchase. Subsequent replacement products  
are warranted for the balance of the original  
warranty period.  
3. Please describe your problem in writing and  
include your name, a return UPS shipping  
address (P.O. Box not acceptable), and a  
daytime phone number with your shipment.  
Who is covered? This warranty is extended to  
the original retail purchaser for products  
purchased and used in the U.S.A.  
4. For more information and for the location of  
the nearest authorized service center please  
contact us by one of the following methods:  
What is covered? This warranty covers all  
defects in material and workmanship in this  
product. The following are not covered:  
installation/removal costs, damage resulting  
from accident, misuse, abuse, neglect, product  
modification, improper installation, incorrect  
line voltage, unauthorized repair or failure to  
follow instructions supplied with the product,  
or damage occurring during return shipment of  
the product.  
• Call us toll-free at 1-866-382-5476  
• Email us at [email protected]  
Exclusion of Certain Damages: This warranty  
is exclusive and in lieu of any and all other  
warranties, expressed or implied, including  
without limitation the implied warranties of  
merchantability and fitness for a particular  
purpose and any obligation, liability, right,  
claim or remedy in contract or tort, whether  
or not arising from the company’s negligence,  
actual or imputed. No person or representative  
is authorized to assume for the company any  
other liability in connection with the sale of  
this product. In no event shall the company be  
liable for indirect, incidental or consequential  
damages.  
16  
XDM6220 OPERATION  
Specifications  
CD Player Signal-to-noise: >92dB  
Frequency response: 10Hz-20kHz  
Channel separation @ 1kHz: >65dB  
D/A converter: 1 Bit  
FM Tuner Tuning range: 87.5MHz-107.9MHz  
Usable sensitivity: 8.5dBf  
50dB quieting sensitivity: 10dBf  
Stereo separation @ 1kHz: 40dB  
Frequency response: 30Hz-13kHz  
AM Tuner Tuning range: 530kHz-1710kHz  
Usable sensitivity: 22uV  
Frequency response: 30Hz-2.2kHz  
General Total power output: 200 Watts Peak  
Power output: 50Wx4 @ 4 ohms, 14.4 VDC  
Operating voltage: 11-16 VDC, negative ground  
Speaker output impedance: 4~8 ohms  
Line output voltage: 2 Volts  
Dimensions: 7" x 7" x 2" (178 x 178 x 51 mm)  
Design and specifications subject to change without notice.  
17  
XDM6220 WARRANTY  
Troubleshooting  
Problem  
Cause  
Action  
Unit will not turn on  
(no power)  
Yellow wire not connected or incorrect voltage Check connections for proper voltage  
Red wire not connected or incorrect voltage  
Black wire not connected  
Fuse blown  
(11~16VDC)  
Check connection to ground  
Replace fuse  
Unit has power  
(but no sound)  
Speaker wires not connected  
Check connections at speakers  
One or more speaker wires touching each  
other or touching chassis ground  
Insulate all bare speaker wires from  
each other and chassis ground  
Unit blows fuses  
Yellow or red wire touching chassis ground  
Speaker wires touching chassis ground  
Incorrect fuse rating  
Check for pinched wire  
Check for pinched wire  
Use fuse with correct rating  
Excessive skipping  
Unit is not mounted correctly or backstrap is Check mounting sleeve and backstrap  
not secure support  
Physical defect in media (CD, CD-R or CD-RW) Check media for scratches  
ERROR-01 appears  
on display  
Disc read error  
Press EJECT or RESET  
Press EJECT or RESET  
Press EJECT or RESET  
Press EJECT or RESET  
Press EJECT or RESET  
ERROR-02 appears  
on display  
Focus error or disc is in upside down  
FAT error  
ERROR-03 appears  
on display  
ERROR-04 appears  
on display  
MP3/WMA decode error  
PROTECT appears  
on display  
The WMA file is DRM protected  
CD mechanism position out of alignment  
CD transit screws still in place  
Unit will not accept  
a disc  
Press EJECT for 3 seconds to reset  
CD mechanism position  
Remove 2 transit screws located on top  
of the unit  
18  
XDM6220 OPERATION  
Notes  
19  
Dual Electronics Corp.  
21318 64th Ave. South  
Kent, WA 98032  
Toll Free: 1-866-382-5476  
©2005 Dual Electronics Corp. All rights reserved.  
Windows Media and the Windows logo are trademarks, or registered trademarks  
of Microsoft Corporation in the United States and or other countries.  
NSA0505-V01  

Nextel comm CLUTCH I465 User Manual
NETGEAR ReadyNAS NVX User Manual
Memorex iWake Mi4004 User Manual
Maxtor One Touch STM305004OTB3E5 RK User Manual
Logitech Wireless Rechargeable Touchpad T650 User Manual
IRiver Slim X iMP iMP 350 User Manual
Datexx EXACTIME DRC 701 User Manual
Cuisinart Fully Automatic Burr Grind &amp; Brew DGB 900BC User Manual
Audiovox CDM 89100C User Manual
Accordance Systems Inc Computer Drive 2000 User Manual