Denon RCD M37 User Manual

CD RECEIVER

RCD-M37

Owner’s Manual

Manuel de l’Utilisateur

Manual del usuario

ESPAÑOL FRANCAIS ENGLISH

FCC Information (For US customers)

1. PRODUCT

This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

product may not cause harmful interference, and (2) this product must accept any interference received, including

interference that may cause undesired operation.

2. IMPORTANT NOTICE: DO NOT MODIFY THIS PRODUCT

This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements.

Modiﬁcation not expressly approved by DENON may void your authority, granted by the FCC, to use the product.

3. NOTE

This product has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation.

This product generates, uses and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation. If this product does cause harmful interference to radio or

television reception, which can be determined by turning the product OFF and ON, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the product into an outlet on a circuit different from that to which the receiver is connected.

• Consult the local retailer authorized to distribute this type of product or an experienced radio/TV technician for

help.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

ENGLISH FRANCAIS ESPAÑOL

NOTE ON USE / OBSERVATIONS RELATIVES A L’UTILISATION / NOTAS

SOBRE EL USO

• Do not let foreign objects into the unit.

• Ne pas laisser des objets étrangers dans

l’appareil.

• No deje objetos extraños dentro del

equipo.

• Keep the unit free from moisture, water,

and dust.

• Protéger l’appareil contre l’humidité, l’eau

et la poussière.

• Mantenga el equipo libre de humedad,

agua y polvo.

• Avoid high temperatures.

Allow for sufﬁcient heat dispersion when

installed in a rack.

• Eviter des températures élevées.

Tenir compte d’une dispersion de chaleur

sufﬁsante lors de l’installation sur une

étagère.

• Evite altas temperaturas.

Permite la suﬁciente dispersión del calor

cuando está instalado en la consola.

• Do not let insecticides, benzene, and

thinner come in contact with the unit.

• Ne pas mettre en contact des insecticides,

du benzène et un diluant avec l’appareil.

• No permita el contacto de insecticidas,

gasolina y diluyentes con el equipo.

• Unplug the power cord when not using the

unit for long periods of time.

• Débrancher le cordon d’alimentation

lorsque l’appareil n’est pas utilisé pendant

de longues périodes.

• Desconecte el cordón de energía cuando

no utilice el equipo por mucho tiempo.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Manipuler le cordon d’alimentation avec

précaution.

Tenir la prise lors du débranchement du

cordon.

• Maneje el cordón de energía con cuidado.

Sostenga el enchufe cuando desconecte el

cordón de energía.

* (For apparatuses with ventilation holes)

• Never disassemble or modify the unit in

any way.

• Ne jamais démonter ou modiﬁer l’appareil

d’une manière ou d’une autre.

• Nunca desarme o modiﬁque el equipo de

ninguna manera.

• Do not obstruct the ventilation holes.

• Ne pas obstruer les trous d’aération.

• No obstruya los oriﬁcios de ventilación.

III

ENGLISH

n Contents

Playback

Setting the Timer

Preparations··················································································13

Turning the Power On ··································································13

Loading Discs···············································································13

Operations Possible During Playback·········································13

Adjusting the Master Volume·······················································13

Input Source Switching································································13

Adjusting theTone········································································13

Turning the Sound OffTemporarily (Muting)·································13

Switching the Display’s Brightness··············································13

Listening with Headphones ·························································13

CD Playback ··················································································14

Playing CDs··················································································14

Playing Repeatedly <Repeat Playback>·······································14

Playing Random Order <Random Playback> ·······························14

PlayingTracks in the Desired Order <Program playback>············15

Switching the Display···································································15

Playback of MP3 andWMA Files ·················································15

About the MP3 and WMA FormatsThat Can be Played ··············15

Playing MP3 and WMA Files························································16

TUNER Playback···········································································17

Tuning in Broadcast Stations························································17

Automatically Presetting FM Stations (Auto Preset)····················17

Presetting FM/AM Stations Manually ··········································17

Listening to Preset Stations·························································18

Naming the CurrentlyTuned in Broadcast Station························18

Timer Playback··············································································22

Setting theTimer··········································································22

SleepTimer Playback ···································································23

Getting Started

Accessories······················································································2

Cautions on Handling·····································································2

Cautions on Installation·································································2

Main Features ·················································································2

Discs·································································································2

Discs usable on the RCD-M37·······················································2

Holding Discs·················································································3

Loading Discs·················································································3

Cautions on Loading Discs·····························································3

Cautions on Handling·····································································3

Cautions on Storing Discs······························································3

Cleaning Discs ···············································································3

About the Remote Control Unit····················································3

Inserting the Batteries····································································3

Operating Range of the Remote Control Unit································4

Part Names and Functions·····························································4

Front Panel·····················································································4

Display ···························································································5

Rear Panel······················································································5

Remote Control Unit······································································6

Other Functions

Convenient Functions ··································································24

Auto Power On·············································································24

Auto Function Selector Function··················································24

Last Function Memory·································································24

Resetting the Microprocessor······················································24

Using an Optimizing Filter····························································24

Troubleshooting····························································· 25

Speciﬁcations·································································· 26

iPod Playback ·············································································18

Connections

Preparations·················································································18

Listening to Audio ········································································19

Disconnecting the iPod ································································19

Playing a Portable Audio······························································19

Connecting a Portable Player ·······················································19

Playing the Portable Player···························································19

USB Playback················································································20

Playable USB Memory Formats···················································20

Basic Operation············································································20

Preparations····················································································8

Cables Used for Connections ························································8

Using the AM Loop Antenna··························································8

Assembling the AM Loop Antenna················································8

Speaker Connections ·····································································9

Connecting the Speaker Cables·····················································9

Connecting the Playback Components ······································ 10

Control Dock for iPod ··································································· 10

Connecting the Recording Components···································· 10

CD Recorder / MD Recorder /Tape deck······································ 10

Connections to Other Devices····················································· 10

AntennaTerminals········································································ 10

USB Port ······················································································ 11

Connecting the Power Cord························································· 11

Once Connections are Completed ·············································· 11

Turning the Power On ·································································· 11

Setup

Setting the CurrentTime (24-Hour Display)·······························12

ꢀ

ENGLISH

Getting Started

Thank you for purchasing this DENON product. To ensure proper

operation, please read this owner’s manual carefully before using the

product.

Cautions on Handling

• Before turning the power switch on

Check once again that all connections are correct and that there are

no problems with the connection cables.

Main Features

1. High quality ampliﬁer stressing sound quality

Equippd with 30 W + 30 W (6 Ω/ohms) high quality ampliﬁer

circuits.

After reading them, be sure to keep them for future reference.

• Power is supplied to some of the circuitry even when the unit is 2. Tone control and SDB control

Accessories

Check that the following parts are supplied with the product.

set to the standby mode. When traveling or leaving home for long

periods of time, be sure to unplug the power cord from the power

outlet.

Separate bass and treble tone controls for adjusting the tone to your

tastes and Super Dynamic Bass (SDB) circuit for producing powerful

bass sound even when the volume is low.

Source direct position provided for turning off the SDB and tone

control circuitry to make the response ﬂat.

• Sufﬁciently ventilate the place of installation

If the unit is left in a room full of the smoke from cigarettes, etc., for

q Remote control (RC-1097) .......................................................1

w R03/AAA batteries...................................................................2

e Power cord (Cord length: Approx. 6.6 ft / 2 m) ........................1

r AM loop antenna.....................................................................1

t FM indoor antenna ..................................................................1

y Owner’s manual ......................................................................1

u Warranty (for North America model only)................................1

i Service station list...................................................................1

long periods of time, the surface of the optical pickup could get dirty, 3. CD player for digital sound

in which case it will not be able to read the signals properly.

Compact body integrating a CD section in addition to the FM/AM

tuner and ampliﬁer, allowing playback of CD-R/RW discs.

• About condensation

If there is a major difference in temperature between the inside of 4. Playback of MP3 andWMA ﬁles

the unit and the surroundings, condensation (dew) may form on

the operating parts inside the unit, causing the unit not to operate

properly.

If this happens, let the unit sit for an hour or two with the power

turned off and wait until there is little difference in temperature

before using the unit.

Supports playback of discs and USB memory devices on which MP3

and WMA ﬁles are recorded. The track name and artist name of the

currently playing track can be displayed on the set’s display.

The characters that can be displayed “Switching the Display”

(vpage 16)

5. Low standby power consumption

• Cautions on using mobile phones

Using a mobile phone near this unit may result in noise. If so, move

the mobile phone away from this unit when it is in use.

Designed with considerations on the environment, with the power

consumption when the power is in standby kept down to about 0.3W.

• Moving the unit

Turn off the power and unplug the power cord from the power

outlet.

Next, disconnect the connection cables to other system units before

moving the unit.

Discs

Discs Usable on the RCD-M37

• Note that the illustrations in these instructions may differ from the

actual unit for explanation purposes.

q Music CDs

Discs marked with the logotype below can be played in this unit.

w CD-R/CD-RW

Cautions on Installation

Note:

For proper heat dispersal, do not install this unit in a conﬁned

space, such as a bookcase or similar enclosure.

b Note

Wall

ꢁ

ENGLISH

NOTE

Cleaning Discs

• Discs with special shapes (heart-shaped discs, octagonal discs, etc.)

cannot be played. Do not attempt to play them, as doing so can

damage the product.

• Some discs and some recording

formats may not be playable.

• “00Tr 00 : 00” is displayed if a disc that cannot be played is loaded.

• “00Tr 00 : 00” is displayed if the disc is loaded upside-down or if no

disc is loaded.

• If there are ﬁngerprints or dirt on discs, wipe them off before using

the disc. Fingerprints and dirt can impair sound quality and cause

interruptions in playback.

• Use a commercially available disc cleaning set or a soft cloth to clean

discs.

NOTE

• Non-ﬁnalized discs cannot be

played.

Do not push the disc tray in by hand when the power is turned off.

Doing so could damage the set.

b What is ﬁnalization?

Finalization is the process that

makes recorded CD-R/CD-RW discs playable on compatible

players.

Cautions on Loading Discs

• Only load one disc at a time. Loading two or more discs can damage

the unit or scratch the discs.

Holding Discs

• Do not use cracked or warped discs or discs that have been repaired

with adhesive, etc.

Gently wipe the disc from the Do not wipe with a circular

• Do not use discs on which the sticky part of cellophane tape or labels

is exposed or on which there are traces of where labels have been

removed. Such discs can get caught inside the player and damage

it.

inside towards the outside.

motion.

Do not touch the signal surface.

NOTE

Do not use record spray, antistatic agents, or benzene, thinner or other

solvents.

Cautions on Handling

Loading Discs

• Do not get ﬁngerprints, oil or dirt on discs.

• Take special care not to scratch discs when removing them from

their cases.

• Do not bend or heat discs.

• Do not enlarge the hole at the center.

About the Remote Control Unit

• Set the disc with the labeled side facing up.

• Make sure the disc tray is fully open when inserting the disc.

• Place the discs ﬂatly, 12 cm discs in the outer tray guide (Figure 1), 8

cm discs in the inner tray guide (Figure 2).

Inserting the Batteries

• Do not write on the labeled (printed) surface with ball-point pens,

pencils, etc., or stick new labels on discs.

q Slide the rear lid in the

direction of the arrow and

remove it.

w Load the two batteries properly

as indicated by the marks in the

battery compartment.

Figure 1

Figure 2

• Water droplets may form on discs if they are moved suddenly from a

cold place (outdoors for example) to a warm place, but do not try to

dry them off using a hairdryer, etc.

Outer tray guide

Inner tray guide

8 cm disc

12 cm disc

Cautions on Storing Discs

• Be sure to remove discs after using them.

• Be sure to store discs in their cases to protect them from dust,

scratches, warping, etc.

• Do not store discs in the following places:

1. Places exposed to direct sunlight for long periods of time

2. Dusty or humid places

• Place 8 cm discs in the inner tray guide without using an adapter.

e Put the rear cover back on.

3. Places exposed to heat from heating appliances, etc.

ꢂ

ENGLISH

NOTE

Part Names and Functions

• Replace the batteries with new ones if the set does not operate even

when the remote control unit is operated close to the unit.

• The supplied batteries are only for verifying operation.

• When inserting the batteries, be sure to do so in the proper direction,

following the “q” and “w” marks in the battery compartment.

• To prevent damage or leakage of battery ﬂuid:

• Do not use a new battery together with an old one.

• Do not use two different types of batteries.

• Do not attempt to charge dry batteries.

• Do not short-circuit, disassemble, heat or dispose of batteries in

ﬂames.

For buttons not explained here, see the page indicated in parentheses ( ).

Front Panel

• If the battery ﬂuid should leak, carefully wipe the ﬂuid off the inside

of the battery compartment and insert new batteries.

• Remove the batteries from the remote control unit if it will not be in

use for long periods.

Operating Range of the Remote Control

Unit

Point the remote control unit at the remote sensor when operating it.

Approx. 23 feet / 7 m

30°

q Power operation button

o Master volume control knob

(ON/STANDBY)······································································(13)

w Power indicator······································································(13)

e USB port (USB)······································································ (11)

r Display

(VOLUME) ··············································································(13)

Q MENU/SET button ··························································(12, 22)

Q SDB/TONE button ································································(13)

Q BAND/Stop button (BAND/2)········································ (14, 17)

Q Play/Pause button (1/3)·······················································(14)

Q Disc tray open/close button (5)···········································(13)

Q Remote control sensor ···························································(4)

Q Disc tray ···················································································(3)

NOTE

t Portable jack (PORTABLE IN)················································(19)

y Headphones jack (PHONES)·················································(13)

u SOURCE button·····································································(13)

The set may function improperly or the remote control unit may not

operate if the remote control sensor is exposed to direct sunlight,

strong artiﬁcial light from an inverter type ﬂuorescent lamp or infrared

light.

i Revers-skip/Forward-skip buttons

(8/–, +/9) ································································· (14, 17)

ꢃ

ENGLISH

Display

Rear Panel

u i

t r

q Information display

Various information is displayed here, depending

on the operation mode.

w 1: (the play indicator) lights when a disc is

playing.

3: (the pause indicator) lights when a disc is

pausing.

e SDB,TONE indicator ………………………(13)

r Reception mode indicator …………………(17)

t TOTAL indicator

Lights when the total number of tracks and total

time of the CD are displayed.

y Play mode indicator ·································· (14)

q Monaural audio connector

u Timer indicator ··········································(23)

(MONO OUT) ···············································(9)

w Speakers terminals······································(9)

e AC inlet (AC IN)·········································· (11)

r FM/AM antenna terminals ························(10)

t DOCK CONTROL jack ································(10)

i F:Flashes when remote control signals are

received.

y AUX1/AUX2

Analog audio connectors··························(10)

ꢄ

ENGLISH

Remote Control Unit

Buttons Operable for All Functions (CD,TUNER, iPod and USB)

Buttons OperableWhen the Function is Set to “CD”

The buttons listed at “Buttons Operable for All Functions” can also be used.

q DIMMER button·········································· (13)

q Number buttons ········································· (14)

w Master volume control buttons

w PROG/DIRECT button ································ (15)

e RANDOM button ········································ (14)

r SOURCE button·········································· (14)

t CD 1/3 button············································ (14)

y FOLDER MODE button······························· (16)

u TIME/DISPLAY button································ (15)

i CLEAR/DEL button····································· (15)

o REPEAT button············································ (14)

(VOLUME) ··················································· (13)

e SDB/TONE button ······································ (13)

r MENU/SET button ····································· (12)

t ON/STANDBY button································· (13)

y SLEEP button··············································(23)

u MUTE button ·············································· (13)

i CLOCK button ············································· (12)

NOTE

Q Fast-reversing/Fast-forwarding buttons

(6, 7) ··················································· (14)

The DAB/RDS button cannot be used.

Q Reverse-skip/Forward-skip buttons

(8, 9)··················································· (14)

Q Stop button (2)··········································· (14)

Q Cursor buttons (uio p)·························· (16)

ꢅ

ENGLISH

Buttons OperableWhen the Function is Set to “TUNER”

Buttons OperableWhen the Function is Set to “iPod”, “USB”

The buttons listed at “Buttons Operable for All Functions” can also be used.

q Number buttons ········································· (18)

q Number buttons ·········································(21)

w SOURCE button·········································· (17)

e TUNER button············································· (17)

r CLEAR/DEL button····································· (18)

t Tuning +, – buttons (TU+,TU–) ·················· (17)

y Channel +, – buttons (CH+, CH–) ··············· (17)

u Stop button (2)··········································· (17)

i ENTER/MEMO button································ (17)

o Cursor buttons (uio p)·························· (17)

w RANDOM button ········································(21)

e SOURCE button··········································(20)

r MENU/SET button ····································· (19)

t FOLDER MODE button·······························(21)

y TIME/DISPLAY button································ (19)

u REPEAT button············································(21)

i Fast-reversing/Fast-forwarding buttons

(6, 7) ···················································(21)

o Reverse-skip/Forward-skip buttons

(8, 9)···················································(21)

Q USB 1/3 button ·········································(20)

Q Stop button (2)···········································(21)

Q iPod 1/3 button ········································ (19)

Q ENTER/MEMO button································ (19)

Q Cursor buttons (uio p)·························· (19)

Q REMOTE/BROWSE button························· (18)

ꢆ

ENGLISH

Connections

Connections for all compatible audio signal formats are described

in this owner’s manual. Please select the types of connections

suited for the equipment you are connecting.

Using the AM Loop Antenna

Preparations

With some types of connections, certain settings must be made

on the RCD-M37. For details, refer to the instructions for the

respective connection items below.

n To use suspended on a wall

Cables Used for Connections

Suspend directly on the wall without assembling.

Select the cables according to the equipment being connected.

NOTE

• Do not plug in the power cord until all connections have been

completed.

Audio cables

• When making connections, also refer to the owner’s manual of the

other components.

Nail, tack, etc.

Analog connections (stereo)

• Be sure to connect the left and right channels properly (left with left,

right with right).

• Do not bundle power supply cords together with connection cables.

Doing so can result in humming or noise.

(White)

(Red)

n To use standing alone

Use the procedure below to assemble.

Stereo pin-plug cable

Analog connections (subwoofer)

(Black)

Pin-plug cable

Speaker connections

Assembling the AM Loop Antenna

Bend in the direction of the arrow.

Speaker cable

Signal direction

Audio signal:

Insert into the hole.

Input

Output

Input

Output

ꢇ

ENGLISH

NOTE

Connecting the Speaker Cables

Speaker Connections

• Use speakers with an impedance of 6 to 16 Ω/ohms. The protection

circuit may be activated if speakers with an impedance other than

speciﬁed are used.

• Connect the speaker cables in a way that they do not stick out of the

speaker terminals.The protection circuit may be activated if the core

wires touch the rear panel or screws or if the + and – sides touch.

• Never touch the speaker terminals while the power is on. Doing so

could cause electric shock.

Check the left (L) and right (R) channels and the + (red) and – (black)

terminals on the set and the speakers to be used and interconnect

the cables to the same polarities.

Subwoofer

Speaker SC-M37 (Supplied)

with built-in

ampliﬁer

Peel off about 10 mm of the sheathing at

the tip of the cable, twist the core wire and

terminate it.

(R)

(L)

Protector circuit

Turn the speaker terminal counterclockwise

The protection circuit will be activated in the following cases:

• When the speaker cable's core wires are touching the rear

panel or screws or when the speaker cable’s + and – sides are

touching

• When the surrounding temperature is extremely high

• When the internal temperature rises due to extended use with a

high output

If this happens, unplug the power cord, then check the connections

of the speaker cables and input cables. If the set’s temperature

is extremely high, wait for it to cool off and improve surrounding

ventilation. After doing this, plug the power cord back in.

If the protection circuit is activated though there are no problems

in ventilation around the set or in connections, the set could be

damaged. Turn off the power, then contact a DENON servicing and

inquiry outlet.

2_{to loosen it.}

Insert the speaker cable’s core wire into the

3_{base of the speaker terminal.}

Turn the speaker terminal counterclockwise

4_{to tighten it.}

When using a banana plug

Tighten the speaker terminal ﬁrmly before inserting the banana

plug.

ꢈ

ENGLISH

Connections to Other Devices

Connecting the Playback

Components

Connecting the Recording

Components

AntennaTerminals

Control Dock for iPod

CD Recorder / MD Recorder /Tape deck

AM/FM

Use a DENON Control Dock for iPod (ASD-1R or ASD-3N/3W, sold

separately ) to connect the set with an iPod.

CD recorder /

MD recorder /

Tape deck

"6%*0

The AM and FM reception sensitivity depends on the place the antenna

is set and the direction in which it is set. Set it so that reception is

best.

iPod

AM loop antenna

(Supplied)

"6%*0

FM indoor antenna

065

"4%ꢀꢁ/ꢂꢁ8

Black

White

Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC which provides guidelines

for proper grounding and, in particular, speciﬁes that the cable

ground shall be connected to the grounding system of the building,

as close to the point of cable entry as practical.

• When using a Control Dock for iPod, the Control Dock for iPod must

be set. For details, refer to the operating instructions of the Control

Dock for iPod.

• To use an iPod, see “iPod Playback” (vpage 18).

ꢀ0

ENGLISH

n Connecting the AM loop antenna

USB Port

Connecting the Power Cord

Push the lever.

USB

Insert the conductor.

Return the lever.

Power cord (Supplied)

To household power outlet

(AC 120 V, 60 Hz)

NOTE

• Make sure the AM loop antenna lead terminals do not touch metal

parts of the panel.

• Do not connect two FM antennas simultaneously.

NOTE

• Only use the supplied power cord.

• Be sure the power cord is unplugged from the power outlet before

connecting or disconnecting it to the AC IN.

NOTE

• It is not possible to connect and use a computer via the RCD-M37’s

USB port using a USB cable.

• For details about USB memory devices, see “Playable USB Memory

Formats” (vpage 20).

Once Connections are

Completed

(vpage 13)

Turning the Power On

ꢀꢀ

ENGLISH

Setup

n Checking the current time when the power is on

Press [CLOCK].

Symbols used to indicate buttons in this manual

Button located on both the main unit and the remote control

Setting the CurrentTime

(12-Hour Display)

When pressed again or if a different operation is performed, the

normal display reappears.

unit

BUTTON

[BUTTON]

Button only on the main unit

Button only on the remote control unit

GExampleH Setting the current time to 10:15 am

n Checking the current time when the power is set

to standby

Press MENU/SET or [CLOCK].

Press again to turn off display.

Press ON/STANDBY to turn the power on.

<5> <1/3> SDB/TONE

8, 9

Press [CLOCK].

The current time is displayed.

• Displaying the time when the power is set to standby consumes

electricity. To reduce electric consumption, turn the time display off.

• When the function is set to iPod, the current time cannot be set.

Press MENU/SET for over 1 second to set the manual

3_{time setting mode.}

The “hours” display ﬂashes.

TIME Adj AM12:00

Use 8, 9 or [o p] to set the “hours”.

TIME Adj AM10:00

Press MENU/SET or [ENTER/MEMO].

The “minutes” display ﬂashes.

ON/STANDBY

SOURCE

TIME Adj AM10:00

MENU/SET

Use 8, 9 or [o p] to set the “minutes”.

[DIMMER]

ON/STANDBY

TIME Adj AM10:15

Press MENU/SET or [ENTER/MEMO].

The current time is set, and the normal display reappears.

SOURCE

8, 9

[CD 1/3]

[VOLUME df]

[MUTE]

SDB/TONE

MENU/SET

[ENTER/MEMO]

[o p]

[CLOCK]

ꢀꢁ

ENGLISH

Playback

[Selectable modes]

Preparations

Operations Possible During

Playback

SDB

Switches Super Dynamic Bass on and off.

BASS

Adjusts the bass sound.

Turning the Power On

[Variable range]

–10dB

+10dB

Press ON/STANDBY.

Adjusting the MasterVolume

TREBLE

Adjusts the treble sound.

• The power turns on. Press again to set the power to standby.

• Power indicator

[Variable range]

–10dB

Either turn <VOLUME> or press [VOLUME df].

Standby∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙Red

Power on∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙Green

When the timer is set∙∙∙∙∙∙∙∙∙∙∙∙Orange

The volume level is displayed.

S.DIRECT

Turns SDB, bass and treble off.

Settings made upon purchase :

• SDB·····················OFF

• BASS·················· 0 dB

[Variable range]

• TREBLE················ 0 dB

• S. DIRECT ·············OFF

VOLUME 00 ~ 45, VOLUME MAX

NOTE

• Power continues to be supplied to some of the circuitry even when

the power is in the standby mode. When leaving home for long

periods of time or when traveling, either press ON/STANDBY to turn

off the power, or unplug the power cord from the power outlet.

• Be sure to stop playback before turning the power off.

Turning the Sound Off Temporarily

(Muting)

Input Source Switching

Press SOURCE to select the input source.

AUX1

(AUX1/Dock)

AUX2

Press [MUTE].

TUNER

The “MUTE ON” is displayed.

n Completely turning off the power

USB

PORTABLE IN

Unplug the power cord from the wall outlet.

b “AUX1/Dock” is displayed when a Control Dock for iPod is

connected to “AUX1”.

b “PORTABLE IN” is only displayed when connected.

b Note that the time setting is cleared when the power cord is

unplugged from the outlet.

b The settings made for the various functions may be cleared if the

power cord is left unplugged from a power outlet for an extended

period of time.

To cancel, press [MUTE] again.

(The mute mode is also canceled when the <VOLUME> control is

turned or a [VOLUME df] is pressed.)

Adjusting the Tone

Switching the Display’s Brightness

Loading Discs

Select the item to be adjusted with SDB/TONE.

Press [DIMMER].

SDB

BASS

In the stop mode, press <5> to open the disc tray.

b “Loading discs” (vpage 3).

70 %

40 %

100 %

S.DIRECT

TREBLE

OFF

n To close the disc tray

b The display’s brightness switches each time the button is

pressed.

GAbout the displayH

Press <5> again.

When the SDB is on ∙∙∙∙∙∙∙∙∙∙∙∙“SDB” is displayed.

When BASS orTREBLE is set to something other than 0 dB

∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙“TONE” is displayed.

b The disc tray also closes when <1/3>, [CD 1/3] or SOURCE is

pressed.

Listening with Headphones

NOTE

Display the mode you want to adjust, then use 8,

9 and [o p] to turn on or off and to adjust the

tone.

Do not place any foreign objects in the disc tray. Doing so could

damage it.

Plug the headphones (sold separately) into the <PHONES>.

The sound from the speakers is automatically cut off.

b If no operation is performed for 5 seconds, the adjustment is

retained and the normal display reappears.

NOTE

Be careful not to set the volume too high when using headphones.

ꢀꢂ

ENGLISH

Playing Repeatedly <Repeat Playback>

Symbols used to indicate buttons in this manual

Button located on both the main unit and the remote control

CD Playback

Press [REPEAT].

unit

BUTTON

[BUTTON]

Playback in the respective repeat mode starts.

Playing CDs

Button only on the main unit

Button only on the remote control unit

Press <1/3> or [CD 1/3].

Single-track repeat

All-track repeat

The “1” indicator lights and playback begins.

8, 9

<1/3>

Repeat off

(indicator turns off)

• If the function is set to something other than “CD”, press [CD 1/3]

to switch the function to “CD” and start playback ( vpage 24 “Auto

Function Selector Function”).

[Selectable items]

(Single-track repeat)

: Only 1 track is played repeatedly.

: All tracks are played repeatedly.

: Normal playback resumes.

• The function can also be switched to “CD” using SOURCE.

ALL

(All-track repeat)

n Stopping Playback

Repeat off (indicator turns off)

Press <BAND/2> or [2].

n Stopping PlaybackTemporarily

Press <1/3> or [CD 1/3].

The “3” is displayed.

b To resume playback, press <13> or [CD 1/3].

Playing Random Order <Random Playback>

<BAND/2

SOURCE

n Fast-Forwarding and Fast-Reversing (searching)

In the stop mode, press [RANDOM].

During playback, press and hold in [6, 7].

The “RANDOM” indicator lights.

n Moving to the Beginning ofTracks (skipping)

During playback, press 8, 9.

b The disc is skipped the number of tracks equal to the number of

times the button is pressed.

b When pressed once in the return direction, playback returns to the

beginning of the currently playing track.

Press <1/3> or [CD 1/3].

The tracks start playing in random order.

NOTE

[NUMBER]

Random play cannot be set or canceled during playback.

To Play the DesiredTrack

[CLEAR/DEL]

[REPEAT]

[6, 7]

8, 9

n Canceling Random Playback

In the stop mode, press [RANDOM].

The “RANDOM” indicator turns off.

(Remote Control Unit Only)

Press [NUMBER] (0 ~ 9, +10) to select the track.

GExampleH :Track 4 : [4]

GExampleH :Track 12 : [+10], [2]

GExampleH :Track 20 : [+10], [+10], [0]

[RANDOM]

[PROG/DIRECT]

SOURCE

NOTE

When [REPEAT] pressed during random playback, the tracks are played

in a different random order after this turn.

[CD 1/3]

[2]

[TIME/DISPLAY]

ꢀꢃ

ENGLISH

Playable MP3/WMA ﬁle

Playing Tracks in the Desired Order

Up to 25 tracks can be programmed.

Playback of MP3 and WMA Files

Sampling

Bit rate

File format

Extension

frequency

There are many music distribution sites on the Internet allowing you

MP3

32, 44.1, 48 kHz 32 ~ 320 kbps

32, 44.1, 48 kHz 64 ~ 160 kbps

.MP3

to download music ﬁles in MP3 or WMA (Windows Media Audio)

format.The music (ﬁles) downloaded from such sites can be stored on

CD-R or CD-RW discs and played on the RCD-M37.

WMA

.WMA

In the stop mode, press [PROG/DIRECT].

The “PGM” indicator lights.

“Windows Media” and “Windows” are registered trademarks or

trademarks in the United States and other countries of Microsoft

Corporation of the United States.

Use [NUMBER] (0 ~ 9, +10) to select the traks.

• Be sure to give ﬁles the extension “.MP3” or “.WMA”. Files with any

other extensions or with no extensions cannot be played.

• Recordings you have made should only be used for your personal

enjoyment, and as per copyright laws may not be used in other ways

without permission of the copyright holder.

b GExampleH To program tracks 3, 12, 7 to play in that order:

Press [PROG/DIRECT], [3], [+10], [2], [7].

Press <1/3> or [CD 1/3].

About the MP3 and WMA Formats That

Can be Played

Playback starts in the programmed order.

CD-R and CD-RW discs created in the format described below can be

played.

n Checking the order of the programmed tracks

In the stop mode, press 9 or 8.

The track numbers are displayed in the programmed order each

time the button is pressed.

Writing software format

ISO9660 level 1

n To clear the last track programmed

In the stop mode, press [CLEAR/DEL].

The last track programmed is cleared each time the button is

pressed.

b When written in other formats, it may not be possible to play the

disc properly.

Maximum number of playable ﬁles and folders

n To clear one programmed track at a time

In the stop mode, use 9 or 8 to select the track to be

cleared, then press [CLEAR/DEL].

Total number of folders + ﬁles: 512

Maximum number of ﬁles in a folder: 255

n Clearing the all programmed track

In the stop mode, press [PROG/DIRECT].

The “PGM” indicator turns off.

File format

MPEG-1 Audio Layer-3

WMA (Windows Media Audio)

When [REPEAT] is pressed, the tracks are played repeatedly in the

programmed order.

Tag data

ID3-Tag (Ver.1x)

META-Tag (Compatible with title, artist and album names)

Switching the Display

Press

[TIME/DISPLAY]

Elapsed time of

Remaining time of

currently playing track

Remaining time for

all remaining tracks

b The display switches each time the button is pressed.

ꢀꢄ

ENGLISH

Switching the Display

During playback, press [TIME/DISPLAY].

Playing MP3 andWMA Files

Symbols used to indicate buttons in this manual

Button located on both the main unit and the remote control

File name display

Title/artist display

Load a CD-R or CD-RW disc containing music ﬁles in

unit

BUTTON

[BUTTON]

the MP3 or WMA format into the disc tray (vpage

3).

Title/album display

Button only on the main unit

Button only on the remote control unit

b The characters that can be displayed are as follows:

Press [FOLDER MODE] and select “Folder Mode” or

A to Z a to z 0 to 9 ^ ’ ( ) * + , - . / = (space)

<1/3> <BAND/2>

SOURCE

“Disc Mode”.

GAbout the displayH

To Play Repeatedly

Press [REPEAT].

Playback starts in the respective repeat mode.

b The selectable repeat modes differ in the “Folder Mode” and the

“Disc Mode”.

When “Folder Mode” is selected ∙∙∙∙∙“FLD” is displayed.

When “Disc Mode” is selected ∙∙∙∙∙∙∙∙“FLD” is not displayed.

Folder Mode :

All the files in the selected folder are played.

Disc Mode :

When “Folder Mode” is selected:

After the selected folder and files are played, all the files in all the

folders are played.

Single-track repeat

Repeat off

Repeat of all the

tracks in the folder

Use [ui] to select the folder to be played.

When “Disc Mode” is selected:

Use 8, 9 or [o p] to select the ﬁle to be

played.

8, 9

MENU/SET

Single-track repeat

All-track repeat

Press <1/3> or [CD 1/3].

Repeat off

(indicator turns off)

n To switch the Folder or File During Playback

• Folder

Use [ui] to select the folder.

• File

[Selectable items]

[NUMBER]

When “Folder Mode” is selected:

Use 8, 9 to select the ﬁle, or use [NUMBER] (0 ~ 9, +10) to

select the ﬁle number.

1FLD

: Only the selected track is played repeatedly.

[REPEAT]

[TU –, TU +]

FLD

b The ﬁle numbers are set automatically when the disc is loaded.

: All the ﬁles in the selected folder are played repeatedly.

SOURCE

[TUNER]

[CD 1/3]

FLD

8, 9

[CH –, CH +]

[2]

: Folder mode playback resumes.

(The “Not Support” is displayed.)

Note that depending on the software used for burning and other

conditions, some ﬁles may not play or display correctly.

When “Disc Mode” is selected:

“Playing Repeatedly <Repeat playback>” (vpage 14)

n Setting random playback

“Playing Random Order <Random playback>” (vpage 14)

MENU/SET

[FOLDER MODE]

[ENTER/MEMO]

Programmed playback is not possible with MP3/WMA discs.

[

uio p]

[TIME/DISPLAY]

ꢀꢅ

ENGLISH

About the FM Broadcast Reception Status Display

Automatically Presetting FM Stations

(Auto Preset)

Up to 40 stations can be preset.

TUNER Playback

The “ST” indicator lights when receiving stereo broadcasts.

Tuning in Broadcast Stations

Connect the antenna beforehand (vpage 10).

Auto preset is not possible with AM broadcast stations.

If the signal is weak and stable stereo reception is not possible, select

“FM MONO” to receive in monaural.

Press [TUNER] to select “FM AUTO” or “FM

Press [TUNER] or <BAND/2> to select the reception

MONO”.

About Switching theTuning Mode and Preset Mode

band.

Use <8/–, +/9> to perform the tuning and preset channel

operations. Switch to the mode to be operated before operating.

Press and hold in MENU/SET.

The “AUTO PRESET” is displayed.

FM AUTO

FM MONO

GAbout the displayH

n To switch to the preset mode

Press <+/9> while pressing <BAND/2>.

The “PRESET” indicator ﬂashes for about 5 seconds.

When FM AUTO is selected∙∙∙∙∙∙∙∙∙∙∙∙∙∙“AUTO” is displayed.

When FM MONO is selected∙∙∙∙∙∙∙∙∙∙∙“MONO” is displayed.

When AM is selected ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙The reception mode is not

displayed.

Press MENU/SET again.

“Search” ﬂashes and auto presetting starts.

n To switch to the tuning mode

Press <8/–> while pressing <BAND/2>.

The “TUNING” indicator ﬂashes for about 5 seconds.

Use <8/–, +/9> or [TU –, TU +] to select the

Broadcast stations whose antenna signal are weak cannot be preset

automatically. If you wish to preset such stations, tune them in

manually.

reception band.

When a station is received, the “TUNED” indication will light.

n To Cancel Auto Presetting

• If the function is set to something other than “TUNER”, press

[TUNER] to switch the function to “TUNER” (vpage 24 “Auto

Function Selector Function”).

Press <BAND/2> or [2].

The “Search” indicator turns off.

• The function can also be switched to “TUNER” using SOURCE.

Presetting FM/AM Stations Manually

Up to 40 stations (total for AM and FM) can be preset.

n ToTune Automatically

Press and hold in <8/–, +/9> or [TU –, TU +] to automatically

search and tune in broadcast stations.

b Stations whose signal is weak cannot be tuned in.

Tune in the station.

n To Stop AutoTuning

Press <8/–, +/9> or [TU –, TU +].

Press [ENTER/MEMO].

n ToTune Manually

The smallest non-registered preset number ﬂashes.

The reception frequency switches each time <8/–, +/9> or

[TU –, TU +] is pressed.

Use <8/–, +/9>, [CH –, CH +] or [o p] to select

the number, then press [ENTER/MEMO].

The preset number, reception band and reception frequency are

displayed.

A humming sound may be heard when using a TV nearby while

receiving AM programs. If this happens, move the system as far from

theTV as possible.

ꢀꢆ

ENGLISH

Listening to Preset Stations

iPod Playback

Symbols used to indicate buttons in this manual

Button located on both the main unit and the remote control

With the RCD-M37, you can listen to music on an iPod. It

is also possible to operate the iPod from the main unit or

remote control unit.

Use <8/–, +/9>, [CH –, CH +] or [NUMBER] (0 ~ 9,

+10) to select the preset number.

b Operate <8/–, +/9> after switching to the preset mode

unit

BUTTON

[BUTTON]

Button only on the main unit

Button only on the remote control unit

(vpage 17).

iPod is a trademark of Apple Inc., registered in the U.S.

and other countries.

<8/–, +/9>

MENU/SET

b The iPod may only be used to copy or play contents that are not

copyrighted or contents for which copying or playback is legally

permitted for your private use as an individual. Be sure to comply

with applicable copyright legislation.

Naming the CurrentlyTuned in Broadcast

Station

Names of up to 8 characters can be input.

Press [NUMBER] (0 ~ 9, +10) for the preset number to

Preparations

be named.

Set the iPod on the DENON Control Dock for iPod.

(vSee the Control Dock for iPod’s operating instructions.)

Press MENU/SET three times.

The “STATION NAME” is displayed.

Press SOURCE to select “AUX1/Dock”.

b Operate within 5 seconds.

ON/STANDBY

Press [o p].

The name input mode is set.

SOURCE

Press [REMOTE/BROWSE] to select the display

mode.

The mode switches each time the button is pressed.

Use [ui] to select the character, then press [p] to

set.

b Characters that can be input.

ON/STANDBY

Browse mode

Remote mode

[Selectable mode]

Display location

Main unit display

iPod display

A to Z a to z 0 to 9 ^ ’ ( ) * + , - . / = (space)

[NUMBER]

SOURCE

Audio file

Video file

Playable

files

b Press [o p] to move the cursor.

Use this to correct input characters.

[CLEAR/DEL]

[CH–, CH+]

Remote

control unit

(RCD-M37)

Active

buttons

Press [ENTER/MEMO].

Naming mode is ﬁnished.

iPod

: Video may not be output, depending on the combination of ASD-

1R and iPod.

n Changing the Broadcast Station Name

q Call out the preset name to be changed, then press MENU/SET

three times.

w Perform steps 3, 4 and 5 at “Naming the Currently Tuned In

Broadcast Station”.

b Press [CLEAR/DEL] to delete the characters.

MENU/SET

[iPod 1/3]

[ENTER/MEMO]

[

uio p

]

[REMOTE/BROWSE]

[TIME/DISPLAY]

ꢀꢇ

ENGLISH

To Switch the Display

Playing a Portable Audio

Listening to Audio

During playback, press [TIME/DISPLAY].

The display switches each time the button is pressed.

Your portable audio player can be connected to the RCD-

M37’s portable jack to play tracks on the portable audio

player.

Use

to select the item, then press

[ENTER/

[

]

1 _MEMO]

to select the music ﬁle to be played.

[

]

Title name

Artist name

Album title

Press

[iPod / ]

1 3

Connecting a Portable Player

2 _{Playback starts.}

Disconnecting the iPod

• If the function is set to something other than “AUX1/Dock”, press

[iPod 1/3] to switch the function to“AUX1/Dock” and start playback.

(vpage 24 “Auto Function Selector Function”)

Press

to set the standby mode.

ON/STANDBY

• The function can also be switched to “AUX1/Dock” using SOURCE.

Remove the iPod from the Control Dock for iPod.

Remote control and iPod button relations

Remote con-

trol unit but- iPod buttons

tons

Operation on the RCD-M37

Play the track.

b Play/Pause in remote mode

iPod

1 3

Play the track from the beginning/

Play the next track.

Portable

8, 9

6, 7

8, 9

Fast-reverse the track/

Fast-forward the track.

)&"%1)0/&

Click Wheel Select an item.

o, p, u, i

Enter the selection or plays the

track.

Connect the RCD-M37 and portable audio player using a separately

sold mini-stereo audio cable.

ENTER/MEMO

Select

–

REMOTE/

BROWSE

Switch between the browse

mode and the remote mode.

REPEAT

–

Switch the repeat function

Switch the shufﬂe function

Playing the Portable Player

RANDOM

Display the menu or return to the

previous menu.

Press SOURCE to select “PORTABLE IN”.

MENU/SET

NOTE

Play the portable audio player.

The Portable Audio are output.

• DENON will accept no responsibility whatsoever for any loss of iPod

data.

b Also read the portable audio player’s operating instructions.

• Depending on the type of iPod and the software version, some

functions may not operate.

NOTE

When using the portable player’s headphones jack, set the volume on

the portable player to an appropriate level.

ꢀꢈ

ENGLISH

Basic Operation

Symbols used to indicate buttons in this manual

Button located on both the main unit and the remote control

USB Playback

Set the USB port to be used.

Playback starts automatically.

unit

BUTTON

[BUTTON]

Playable USB Memory Formats

Button only on the main unit

Button only on the remote control unit

b When a USB memory device is connected, playback starts

automatically when the operation below is performed.

• Switch the function to “USB” using SOURCE.

• Press [USB 1/3].

Files stored on USB memory devices created in the formats below

can be played.

<1/3>

8, 9

USB-Compatible File Systems

“FAT16” or “FAT32”

• If the function is set to something other than “USB”, press [USB

1/3] to switch the function to “USB” and start playback.

(vpage 24 “Auto Function Selector Function”)

b If the USB memory device is divided into multiple partitions, only

the top drive can be selected.

• The function can also be switched to “USB” using SOURCE.

Maximum number of playable ﬁles and folders

Maximum number of ﬁles in a folder: 255

Maximum number of folders: 255

File Format

MPEG-1 Audio Layer-3

WMA (Windows Media Audio)

SOURCE

Tag Data

ID3-Tag (Ver.1x)

META-Tag (Compatible with title, artist and album names)

Playable MP3/WMA ﬁle

Sampling

frequency

[NUMBER]

File format

Bit rate

Extension

.mp3

.wma

MP3

32, 44.1, 48 kHz 32 ~ 320 kbps

32, 44.1, 48 kHz 64 ~ 192 kbps

WMA

[REPEAT]

[RANDOM]

SOURCE

[6, 7]

8, 9

[USB 1/3]

Only music ﬁles that are not copyright-protected can be played on this

set.

b Contents downloaded from pay sites on the Internet are copyright

protected. Also, ﬁles encoded in WMA format when ripped from a

CD, etc., on a computer may be copyright protected, depending on

the computer’s settings.

[2]

[FOLDER MODE]

[TIME/DISPLAY]

[ui]

ꢁ0

ENGLISH

n To Switch the “Folder Mode” or “Memory Mode”

Press [FOLDER MODE].

NOTE

• DENON will take no responsibility whatsoever for any loss or damage

to data on USB memory devices when using the USB memory

device connected to the RCD-M37.

GAbout the displayH

When “Folder Mode” is selected∙∙∙∙∙∙∙∙“FLD” is displayed.

When “Memory Mode” is selected∙∙∙∙“FLD” is not displayed.

Folder Mode :

All the files in the selected folder are played.

Memory Mode :

• USB memory devices will not work via a USB hub.

• DENON does not guarantee that all USB memory devices will

operate or be suppled power. When using a USB connection type

portable hard disk of the type for which power can be supplied by

connecting an AC adapter, we recommend using the AC adapter.

After the selected folder and files are played, all the files in all the

folders are played.

n To Switch the Folder or File During Playback

• Folder

Use [ui] to select the folder.

• File

Use 8, 9 to select the ﬁle, or use [NUMBER] (0 ~ 9, +10)

to select the ﬁle number.

n Stopping Playback

Press <BAND/2> or [2].

n Stopping PlaybackTemporarily

Press <1/3> or [USB 1/3].

The “3” is displayed.

b To resume playback, press <1/3> or [USB 1/3].

n Fast-Forwarding and Fast-Reversing (searching)

During playback, press and hold in [6, 7].

Playing Repeatedly (Memory mode only)

Press [REPEAT].

Playing Random Order (Memory mode only)

In the stop mode, press [RANDOM].

Switching the Display

During playback, press [TIME/DISPLAY].

File name display

Title/artist display

Title/album display

b The characters that can be displayed are as follows:

A to Z a to z 0 to 9 ^ ’ ( ) * + , - . / = (space)

ꢁꢀ

ENGLISH

Setting theTimer

Symbols used to indicate buttons in this manual

Use 8, 9 or [o p] to select the function to be

Timer Playback

played.

Button located on both the main unit and the remote control

The everyday timer, once timer and sleep timer can be set.

unit

BUTTON

[BUTTON]

AUX1

(AUX1/Dock)

TUNER

Timer order of priority

Button only on the main unit

Button only on the remote control unit

The order of priority when the times set for the different

timers overlap is as follows:

1. Sleep timer

2. Once timer

3. Everyday timer

USB

AUX2

C D

MENU/SET

Press MENU/SET or [ENTER/MEMO].

The function to be played is set.

b If the function is set to anything other than the tuner, the setting

display shown in step 7 is displayed.

Setting theTimer

GOnly when the “TUNER” function is selectedH

• Everyday timer playback

-q Use 8, 9 or [o p] to select the preset

Playback starts (the power turns on) and stops (the power

turns off) at the set times each day.

• Once timer playback

Playback starts (the power turns on) and stops (the power

turns off) once only at the set times.

number.

E<P02:REG_NAME>

-w Press MENU/SET or [ENTER/MEMO].

The broadcast station for the selected preset number is

set.

8, 9

ON/STANDBY

VOLUME

Press MENU/SET.

Use 8, 9 or [o p] to set the “hours” for the

The “TIMER” is displayed.

timer start time.

ON AM12:00

b Operate within 5 seconds.

ON/STANDBY

Press MENU/SET or [ENTER/MEMO].

Use 8, 9 or [o p] to select the timer play

[SLEEP]

The “hours” for the timer start time are set.

mode.

ONCE

EVERYDAY

Use 8, 9 or [o p] to set the “minutes” for the

z “1” : Once timer, “E” : Everyday timer

< EVERYDAY >

timer start time.

ON AM10:00

Press MENU/SET or [ENTER/MEMO].

The timer play mode is set.

Press MENU/SET or [ENTER/MEMO].

10_{The “minutes” for the timer start time are set.}

8, 9

Use 8, 9 or [o p] to set the “hours” for the

11_{timer stop time.}

[2]

OFF AM12:00

VOLUME

Press MENU/SET or [ENTER/MEMO].

12_{The “hours” for the timer stop time are set.}

[ENTER/MEMO]

MENU/SET

[

o p]

ꢁꢁ

ENGLISH

n To check the timer settings

q Press MENU/SET.

Use 8, 9 or [o p] to set the “minutes” for the

SleepTimer Playback

13_{timer stop time.}

The “TIMER” is displayed.

Use this function to automatically switch the power to the

standby mode after a speciﬁc amount of time (minutes).

The sleep timer can be set to up to 90 minutes, in steps

of 10 minutes.

OFF AM12:00

w Press 8, 9 or [o p].

The “EVERYDAY” or “ONCE” is displayed.

e Press MENU/SET.

Press MENU/SET or [ENTER/MEMO].

The “minutes” for the timer stop time are set.

The display switches each time the button is pressed.

Select and play the desired function.

Use 8, 9 or [o p] to turn timer playback on.

n To change the timer settings

Repeat the procedure under “Setting theTimer” (vpage 22).

1_OFF/E_ON

Press [SLEEP] and select the setting time.

n To change the setting while setting the timer

Press <BAND/2> or [2].

Display

Once timer

Everyday timer

1_off/E_off

OFF

Return to step 2 under “Setting the Timer” (vpage 22). Repeat

the procedure.

(“SLEEP “ indicator turns off)

1_on/E_on

1_off/E_on

1_on/E_off

OFF

The “SLEEP” indicator ﬂashes.

n To clear the timer settings

OFF

q Press MENU/SET.

Press [SLEEP] while the “SLEEP” indicator is

The “TIMER” is displayed.

b When turned on, “

” lights.

ﬂashing.

w Press 8, 9 or [o p].

The set time is displayed.

The “EVERYDAY” or “ONCE” is displayed.

e While “EVERYDAY” or ”ONCE” is displayed, press <BAND/2> or

[2] for at least 2 seconds.

Press MENU/SET or [ENTER/MEMO].

b After about 5 seconds, the set returns to as it was before the

16_{The timer setting is set.}

sleep timer was set, and the “SLEEP” indicator lights.

Adjust the volume for when the timer starts using

n If there is a power failure

17_VOLUME.

n Canceling the sleep timer

The time setting and the timer settings are cleared. Reset the

current time, then reset the timer.

Either press [SLEEP] at step 2 under “Sleep Timer Playback” until

“OFF” is displayed, or press ON/STANDBY.

Set the power to standby.

n When performing a timer setting with DENON

The timer playback standby mode is set.

To change the setting while the sleep timer is set

Press [SLEEP].

control dock for iPod (ASD-3N or ASD-3W)

Pause the track you want to play, and keep the power on for DENON

control dock for iPod.

n Canceling the timer

Checking the time remaining until the sleep timer

starts

Press [SLEEP].

Return to step 2 under “SleepTimer Playback”.

Press MENU/SET twice.

At step 15 under “Setting theTimer”, use 8, 9 or [o p] to

turn off the timer on/off indicator and turn off “

”.

When the function is set to iPod, the timer cannot be set. To set the

timer, ﬁrst switch to a function other than iPod.

ꢁꢂ

ENGLISH

Other Functions

Symbols used to indicate buttons in this manual

Resetting the Microprocessor

Convenient Functions

Button located on both the main unit and the remote control

Perform this procedure if the display is abnormal or if

operations cannot be performed.

unit

BUTTON

[BUTTON]

Button only on the main unit

Button only on the remote control unit

Auto Power On

When the microprocessor is reset, all the settings are

reset to their default values.

When the power is in standby, the power turns on when

any of the buttons below other than ON/STANDBY is

operated, and the respective operation is performed.

• <5>∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙The disc tray opens.

<5>

1/3

MENU/SET

Unplug the power cord.

• 1/3 for the different functions

∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙Playback of that source starts.

• [TUNER]∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙Playback of the tuner starts.

Plug the power cord into a power outlet while pressing

<8/–> and <MENU/SET> simultaneously.

Press [CLOCK].

NOTE

The “AM12:00” display ﬂashes.

The Auto Power On function cannot be used with iPods.

If “AM12:00” is not ﬂashed in step 3, start over from step 1.

Auto Function Selector Function

When one of the buttons below is pressed, the function

switches to the respective function and playback of that

source starts.

< 8/–, +/9 >

ON/STANDBY

Using an Optimizing Filter

An optimizing ﬁlter suited for the properties of the speakers

(SC-M37) can be used.

• [CD 1/3]∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙The function switches to “CD” and the

CD starts playing.

ON/STANDBY

• [USB 1/3]∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙The function switches to “USB” and the

USB starts playing.

Press MENU/SET to select “SP OPTIMISE”.

• [iPod 1/3]∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙The function switches to “AUX1/Dock”

and the iPod starts playing.

• [TUNER] ∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙∙The functions switches to “TUNER” and

the band last set is tuned in.

Use <8/–, +/9> or [o p] to select “ON” or

“OFF”.

Press MENU/SET to set.

Last Function Memory

[TUNER]

[CD 1/3]

[Selectable items]

This stores the settings as they were directly before the

standby mode was set.

[USB 1/3]

When the power is turned back on, the settings are

restored to as they were directly before the standby mode

was set.

:The response is optimized for the speakers (SC-M37,

supplied).

OFF

:The response is ﬂat.

[iPod 1/3]

MENU/SET

[CLOCK]

[

o p]

When the function is set to iPod, the set cannot be switched between

on and off.

ꢁꢃ

ENGLISH

Troubleshooting

If a problem should arise, ﬁrst check the following:

GRemote Control UnitH

1. Are the connections correct?

2. Is the set being operated as described in the owner’s manual?

3. Are the other components operating properly?

If this unit does not operate properly, check the items listed in the table below. Should the problem persist,

there may be a malfunction.

In this case, disconnect the power immediately and contact your store of purchase.

Symptom

Set does not work • Batteries are worn.

properly when

remote control

unit operated.

Cause

Countermeasure

• Replace with new batteries.

Page

• You are operating outside of the • Operate within the speciﬁed

speciﬁed range. range.

• Obstacle between main unit and • Remove the obstacle.

remote control unit.

• The batteries are not inserted in • Insert the batteries in the

the proper direction, as indicated proper direction, following the

by the polarity marks in the polarity marks in the battery

GGeneralH

Symptom

Cause

Countermeasure

Page

Set does not

operate properly.

• External noise or interference is • Reset the microprocessor.

causing the set to malfunction.

battery compartment.

compartment.

• The set’s remote control sensor • Move the set to a place in which

is exposed to strong light (direct the remote control sensor will

sunlight,invertertypeﬂuorescent not be exposed to strong light.

bulb light, etc.).

Display not lit

and sound not

produced when

power switch set

to on.

• Power cord not plugged in

securely.

• Check the connections on

the set's rear panel and the

connection of the power plug to

the power outlet.

GCDH

Display lit but

sound not

produced.

• Device you want to play and set • Select an appropriate input

input source do not match. source.

• Volume control set to minimum. • Turn volume up to suitable level.

• MUTING is on. • Switch off MUTING.

Symptom

Cause

Countermeasure

Page

“00Tr 00 : 00”

is shown on the

display even

though a CD is

loaded.

Disc is not played • The disc is dirty or scratched.

when CD 1/3

button is pressed.

• The disc is not properly loaded. • Reload the disc.

Display is off.

• The Dimmer setting is set to • Set to something other than

“OFF”. “OFF”.

• Protection circuit activated due • Turn off the power, wait for the

Power turns off

suddenly and

power indicator

ﬂashes red.

• Wipe the dirt off the disc or

replace the disc.

to rise of internal temperature.

set to fully cool down, then turn

the power back on.

• Place the set in a well-ventilated

place.

• Core wires of two speakers are • First unplug the power cord,

touching each other or a core then twist the core wires tightly

wire is sticking out of the terminal or terminate the speaker cables,

and touching the set’s rear panel, then reconnect.

A speciﬁc part

of a disc is not

played.

• The disc is dirty or scratched.

• Wipe the dirt off the disc or

replace the disc.

A CD-R or CD-RW • The disc has not been ﬁnalized. • Finalize the disc then play it.

disc cannot be

played.

–

• The recording conditions are bad • Use a properly recorded disc.

or the quality of the disc itself it

poor.

• The ﬁle formats, extensions or • Create discs with ﬁle formats,

settings made when disc was extensionsorsettingscompatible

created are not compatible with with the RCD-M37.

the RCD-M37.

activating the protection circuit.

–

• Set is damaged.

• Turn off the power and contact a

DENON service center.

MP3 and WMA

ﬁles cannot be

played.

ꢁꢄ

ENGLISH

GTunerH

Symptom

Cause

Countermeasure

Page

Speciﬁcations

Continuous noise • Antenna cable is not properly • Connect the antenna cable

is heard when

receiving FM

programs.

connected.

properly.

• Connect an outdoor antenna.

–

Audio section

• Power amplifer

Rated output:

Hissing or

• This may be noise from a TV or • Turn off theTV.

interference from a radio station. • Change the position and direction

of the AM loop antenna.

–

30 W + 30 W (6 Ω/ohms, 1 kHzT.H.D 10 %)

continuous noise

is heard when

receiving AM

programs.

Tuner section

Reception frequency range:

Receiving sensitivity:

FM stereo separation:

FM: 87.5 MHz ~ 107.9 MHz

FM: 1.5 μV/75 Ω/ohms

35 dB (1 kHz)

AM: 520 kHz ~ 1710 kHz

AM: 20 μV

CD section

Playback frequency response:

Wow & ﬂutter:

GiPodH

2 Hz ~ 20 kHz

Below measurable limits ( 0.001%)

44.1 kHz

Symptom

iPod cannot be

played.

Cause

• Device you want to play and set • Select an appropriate input

input source do not match. source.

• Cable is not properly connected. • Reconnect.

• Control Dock for iPod’s AC • Plug the Control Dock for iPod’s

adapter is not connected to AC adapter into a power outlet.

power outlet.

Countermeasure

Page

Sampling frequency:

Clock/Timer section

Clock method:

Timer:

–

Crystal oscillator (Within 1 ~ 2 minutes per month)

Everyday/Once timer: One system each

Sleep timer: 90 minutes, maximum

General

Power supply:

Power consumption:

AC 120 V, 60 Hz

65 W

GUSBH

Approx. 0.3 W (standby)

210 (W) x 115 (H) x 308.5 (D) mm (8-17/64” x 4-33/64” x 12-9/64”)

4.3 kg (9 lbs 7 oz)

Symptom

Cause

Countermeasure

Page

Maximum external dimensions:

Weight:

When a USB

memory device

is connected,

“USB” is not

displayed.

• The set cannot recognize a USB • Check the connection.

memory device.

• A USB memory device not • Connect a USB memory device

conformingtomassstorageclass conforming to mass storage

or MTP standards is connected.

• A USB memory device that • This is not a malfunction. DENON

the set cannot recognize is does not guarantee that all USB

–

Remote control unit (RC-1097)

Remote control method:

Power supply:

Maximum external dimensions:

Weight:

IR pulse method

R03/AAAType (two batteries)

49 (W) x 220 (H) x 24 (D) mm (1-59/64” x 8-21/32” x 15/16”)

110 g (Approx. 3 oz) (including batteries)

class or MTP standards.

b For purposes of improvement, speciﬁcations and design are subject to change without notice.

connected.

memory devices will operate or

receive power.

• USBmemorydeviceisconnected • Connect the USB memory device

via USB hub. directly to the USB port.

• USB memory device is in format • Set the format to FAT16 or

–

Files on a USB

memory device

cannot be played.

other than FAT16 or FAT32.

FAT32. For details, refer to the

USB memory device’s operating

instructions.

• USB memory device is divided • When divided into multiple

–

into multiple partitions.

partitions, only ﬁles stored in the

top partition can be played.

non- • Record the ﬁles in a compatible

format.

• Files are stored in

compatible format.

• You are attempting to play a ﬁle • Files that are copyright protected

that is copyright protected. cannot be played on this set.

ꢁꢅ

www.denon.com

Denon Brand Company, D&M Holdings Inc.

Printed in China 5411 10028 000D

SPEAKER

SC-M37

Owner’s Manual

Bedienungsanleitung

Manuel de l’Utilisateur

Manuale delle istruzioni

Manual del usuario

Gebruiksaanwijzing

Bruksanvisning

ENGLISH DEUTSCH FRANCAIS ITALIANO ESPAÑOL NEDERLANDS SVENSKA

SAFETY PRECAUTIONS For Europe model

• DECLARACIÓN DE CONFORMIDAD

Declaramos bajo nuestra exclusiva responsabilidad que este producto al

que hace referencia esta declaración, está conforme con los siguientes

estándares:

• DECLARATION OF CONFORMITY

CAUTION

e declare under our sole responsibility that this product, to which this

declaration relates, is in conformity with the following standards:

EN55013 and EN55020.

Following the provisions of 2004/108/EC Directive.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

EN55013 y EN55020.

Siguiendo las provisiones de las Directivas 2004/108/EC.

• ÜBEREINSTIMMUNGSERKLÄRUNG

CAUTION:

• EENVORMIGHEIDSVERKLARING

Wir erklären unter unserer Verantwortung, daß dieses Produkt, auf das sich

diese Erklärung bezieht, den folgenden Standards entspricht:

EN55013 und EN55020.

TO REDUCETHE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICINGTO QUALIFIED SERVICE PERSONNEL.

Wij verklaren uitsluitend op onze verantwoordelijkheid dat dit produkt,

waarop deze verklaring betrekking heeft, in overeenstemming is met de

volgende normen:

Entspricht den Verordnungen der Direktive 2004/108/EC.

The lightning ﬂash with arrowhead symbol, within an equilateral

triangle, is intended to alert the user to the presence of

uninsulated “dangerous voltage” within the product’s enclosure

that may be of sufﬁcient magnitude to constitute a risk of electric

shock to persons.

EN55013 en EN55020.

Volgens de bepalingen van de Richtlijnen 2004/108/EC.

• DECLARATION DE CONFORMITE

Nous déclarons sous notre seule responsabilité que l’appareil, auquel se

réfère cette déclaration, est conforme aux standards suivants:

EN55013 et EN55020.

• ÖVERENSSTÄMMELSESINTYG

Härmed intygas helt på eget ansvar att denna produkt, vilken detta intyg

avser, uppfyller följande standarder:

EN55013 och EN55020.

Enligt stadgarna i direktiv 2004/108/EC.

D’après les dispositions de la Directive 2004/108/EC.

The exclamation point within an equilateral triangle is intended

to alert the user to the presence of important operating

and maintenance (servicing) instructions in the literature

accompanying the appliance.

• DICHIARAZIONE DI CONFORMITÀ

Dichiariamo con piena responsabilità che questo prodotto, al quale la nostra

dichiarazione si riferisce, è conforme alle seguenti normative:

EN55013 e EN55020.

DENON Europe

WARNING:

Division of D&M Germany GmbH

An der Landwehr 19, Nettetal,

D-41334 Germany

In conformità con le condizioni delle direttive 2004/108/EC.

TO REDUCETHE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSETHIS APPLIANCETO RAIN OR MOISTURE.

NOTA RELATIVA AL RICICLAGGIO:

A NOTE ABOUT RECYCLING:

I materiali di imballaggio di questo prodotto sono riutilizzabili e riciclabili. Smaltire i materiali conformemente alle

normative locali sul riciclaggio.

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials

in accordance with the local recycling regulations.

Per smaltire l’unità, osservare la normativa in vigore nel luogo di utilizzo.

Non gettare le batterie, né incenerirle, ma smaltirle conformemente alla normativa locale sui riﬁuti chimici.

Questo prodotto e gli accessori inclusi nell’imballaggio sono applicabili alla direttiva RAEE, ad eccezione delle

batterie.

When discarding the unit, comply with local rules or regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with the local

regulations concerning chemical waste.

This product and the accessories, packed together constitute the applicable product according to the

WEEE directive except batteries.

ACERCA DEL RECICLAJE:

Los materiales de embalaje de este producto son reciclables y se pueden volver a utilizar. Disponga de estos materiales

siguiendo los reglamentos de reciclaje de su localidad.

Cuando se deshaga de la unidad, cumpla con las reglas o reglamentos locales.

Las pilas nunca deberán tirarse ni incinerarse. Deberá disponer de ellas siguiendo los reglamentos de su localidad

relacionados con los desperdicios químicos.

HINWEIS ZUM RECYCLING:

Das Verpackungsmaterial dieses Produktes ist für zum Recyceln geeignet und kann wieder verwendet werden. Bitte

entsorgen Sie alle Materialien entsprechend der örtlichen Recycling-Vorschriften.

Beachten Sie bei der Entsorgung des Gerätes die örtlichen Vorschriften und Bestimmungen.

Die Batterien dürfen nicht in den Hausmüll geworfen oder verbrannt werden; bitte geben Sie die Batterien gemäß

örtlichen Bestimmungen an den Sammelstellen oder Sondermüllplätzen ab.

Dieses Produkt zusammen mit den Zubehörteilen ist das geltende Produkt der WEEE-Direktive, davon ausgenommen

sind die Batterien.

Este producto junto con los accesorios empaquetados es el producto aplicable a la directiva RAEE excepto pilas.

EEN AANTEKENINGWAT BETREFT HET RECYCLEREN:

Het inpakmateriaal van dit product is recycleerbaar en kan opnieuw gebruikt worden. Er wordt verzocht om zich van elk

afvalmateriaal te ontdoen volgens de plaatselijke voorschriften.

Volg voor het wegdoen van de speler de voorschriften voor de verwijdering van wit- en bruingoed op.

Batterijen mogen nooit worden weggegooid of verbrand, maar moeten volgens de plaatselijke voorschriften betreffende

chemisch afval worden verwijderd.

Op dit product en de meegeleverde accessoires, m.u.v. de batterijen is de richtlijn voor afgedankte elektrische en

elektronische apparaten (WEEE) van toepassing.

UNE REMARQUE CONCERNANT LE RECYCLAGE:

Les matériaux d’emballage de ce produit sont recyclables et peuvent être réutilisés. Veuillez disposer de tout matériau

conformément aux réglements de recylage locaux.

Lorsque vous mettez cet appareil au rebut, respectez les lois ou réglementations locales.

Les piles ne doivent jamais être jetées ou incinérées, mais mises au rebut conformément aux réglements locaux

concernant les déchets chimiques.

EN KOMMENTAR OM ÅTERVINNING:

Ce produit et les accessoires emballés ensemble sont des produits conformes à la directive DEEE sauf pour les piles.

Produktens emballage är återvinningsbart och kan återanvändas. Kassera det enligt lokala återvinningsbestämmelser.

När du kasserar enheten ska du göra det i överensstämmelse med lokala regler och bestämmelser.

Batterier får absolut inte kastas i soporna eller brännas. Kassera dem enligt lokala bestämmelser för kemiskt avfall.

Denna apparat och de tillbehör som levereras med den är de som uppfyller gällande WEEE-direktiv, med undantag av

batterierna.

SVENSKA NEDERLANDS ESPAÑOL ITALIANO FRANCAIS DEUTSCH ENGLISH

NOTE ON USE / HINWEISE ZUM GEBRAUCH / OBSERVATIONS RELATIVES A L’UTILISATION / NOTE SULL’USO /

NOTAS SOBRE EL USO / ALVORENSTE GEBRUIKEN / OBSERVERA

CAUTION:

• The ventilation should not be impeded by covering the ventilation openings with items,

such as newspapers, tablecloths, curtains, etc.

• No naked ﬂame sources, such as lighted candles, should be placed on the apparatus.

• Attention should be drawn to the environmental aspects battery disposal.

• Do not expose the set to dripping or splashing ﬂuids.

• No objects ﬁlled with liquids, such as vases, shall be placed on the apparatus.

ACHTUNG:

• Die Belüftung sollte auf keinen Fall durch das Abdecken der Belüftungsöffnungen durch

Gegenstände wie beispielsweise Zeitungen, Tischtücher, Vorhänge o. Ä. behindert

werden.

• Auf dem Gerät sollten keinerlei direkte Feuerquellen wie beispielsweise angezündete

Kerzen aufgestellt werden.

• Bitte beachten Sie bei der Entsorgung der Batterien die geltenden Umweltbestimmungen.

• Das Gerät sollte keiner tropfenden oder spritzenden Flüssigkeit ausgesetzt werden.

• Auf dem Gerät sollten keinerlei mit Flüssigkeit gefüllten Behälter wie beispielsweise Vasen

aufgestellt werden.

• Do not let foreign objects into the set.

•

Keine fremden Gegenstände in das Gerät kommen lassen.

• Keep the apparatus free from moisture, water, and dust.

• Halten Sie das Gerät von Feuchtigkeit, Wasser und Staub

fern.

• Avoid high temperatures.

Allow for sufﬁcient heat dispersion when installed in a rack.

• Vermeiden Sie hoheTemperaturen.

Beachten Sie, dass eine ausreichende Belüftung gewährleistet

wird, wenn das Gerät auf ein Regal gestellt wird.

• Eviter des températures élevées.

Tenir compte d’une dispersion de chaleur sufﬁsante lors de

l’installation sur une étagère.

• Evitate di esporre l’unità a temperature elevate.

Assicuratevi che vi sia un’adeguata dispersione del calore

quando installate l’unità in un mobile per componenti audio.

• Evite altas temperaturas.

Permite la suﬁciente dispersión del calor cuando está

instalado en la consola.

• Ne pas laisser des objets étrangers dans l’appareil.

• E’ importante che nessun oggetto

dell’unità.

• No deje objetos extraños dentro del equipo.

• Laat geen vreemde voorwerpen in dit apparaat vallen.

• Se till att främmande föremål inte tränger in i apparaten.

inserito all’interno

• Protéger l’appareil contre l’humidité, l’eau et la poussière.

• Tenete l’unità lontana dall’umidità, dall’acqua

polvere.

dalla

• Mantenga el equipo libre de humedad, agua y polvo.

• Laat geen vochtigheid, water of stof in het apparaat

binnendringen.

ATTENTION :

• La ventilation ne doit pas être gênée en recouvrant les ouvertures de la ventilation avec des

objets tels que journaux, rideaux, tissus, etc.

• Utsätt inte apparaten för fukt, vatten och damm.

• Aucune ﬂamme nue, par exemple une bougie, ne doit être placée sur l’appareil.

• Veillez à respecter I’environnement lorsque vous jetez les piles usagées.

• L’appareil ne doit pas être exposé à l’eau ou à l’humidité.

• Aucun objet conten ant du liquide, par exemple un vase, ne doit étre placé sur l’appareil.

• Vermijd hoge temperaturen.

Zorg vocr een degelijk hitteafvoer indien het apparaat op

een rek wordt geplaatst.

• Undvik höga temperaturer.

Se till att det ﬁnns möjlighet till god värmeavledning vid

montering i ett rack.

PRECAUZIONI:

• Le aperture di ventilazione non devono essere ostruite coprendole con oggetti, quali

giornali, tovaglie, tende e così via.

• Do not let insecticides, benzene, and thinner come in

contact with the apparatus.

• Lassen Sie das Gerät nicht mit Insektiziden, Benzin oder

Verdünnungsmitteln in Berührung kommen.

• Ne pas mettre en contact des insecticides, du benzène et

un diluant avec l’appareil.

• Assicuratevvi che l’unità non venga in contatto con

insetticidi, benzolo o solventi.

• No permita el contacto de insecticidas, gasolina y diluyentes

con el equipo.

• Laat geen insektenverdelgende middelen, benzine of

verfverdunner met dit apparaat in kontakt komen.

• Se till att inte insektsmedel på spraybruk, bensen och

thinner kommer i kontakt med apparatens hölje.

• Non posizionate sull’unità ﬁamme libere, come ad esempio le candele accese.

• Prestate attenzione agli aspetti legati alla tutela dell’ambiente quando si smaltisce la

batterie.

• L’apparecchiatura non deve essere esposta a gocciolii o spruzzi.

• Non posizionate sull’apparecchiatura nessun oggetto contenente liquidi, come ad esempio

i vasi.

• Unplug the power cord when not using the apparatus for

long periods of time.

• Wenn das Gerät längere Zeit nicht verwendet werden soll,

trennen Sie das Netzkabel vom Netzstecker.

• Débrancher le cordon d’alimentation lorsque l’appareil n’est

pas utilisé pendant de longues périodes.

• DisinnestateilﬁlodialimentazionequandoaveteI’intenzione

di non usare il ﬁlo di alimentazione per un lungo periodo di

tempo.

• Desconecte el cordón de energía cuando no utilice el equipo

por mucho tiempo.

PRECAUCIÓN:

• La ventilación no debe quedar obstruida por haberse cubierto las aperturas con objetos

como periódicos, manteles, cortinas, etc.

• No debe colocarse sobre el aparato ninguna fuente inﬂamable sin protección, como velas

encendidas.

• A la hora de deshacerse de las pilas, respete la normativa para el cuidado del medio

ambiente.

• No exponendrà el aparato al goteo o salpicaduras cuando se utilice.

• No se colocaràn sobre el aparato objetos llenos de líquido, como jarros.

•

Neem altijd het netsnoer uit het stopkontakt wanneer het

apparaat gedurende een lange periode niet wordt gebruikt.

• Koppla ur nätkabeln om apparaten inte kommer att användas

i lång tid.

• Handle the power cord carefully.

Hold the plug when unplugging the cord.

• Gehen Sie vorsichtig mit dem Netzkabel um.

Halten Sie das Kabel am Stecker, wenn Sie den Stecker

herausziehen.

WAARSCHUWING:

• De ventilatie mag niet worden belemmerd door de ventilatieopeningen af te dekken met

bijvoorbeeld kranten, een tafelkleed, gordijnen, enz.

• Manipuler le cordon d’alimentation avec précaution.

Tenir la prise lors du débranchement du cordon.

• Manneggiate il ﬁlo di alimentazione con cura.

Agite per la spina quando scollegate il cavo dalla presa.

• Maneje el cordón de energía con cuidado.

Sostenga el enchufe cuando desconecte el cordón de

energía.

• Hanteer het netsnoer voorzichtig.

Houd het snoer bij de stekker vast wanneer deze moet

worden aan- of losgekoppeld.

• Plaats geen open vlammen, bijvoorbeeld een brandende kaars, op het apparaat.

• Houd u steeds aan de milieuvoorschriften wanneer u gebruikte batterijen wegdoet.

• Stel het apparaat niet bloot aan druppels of spatten.

• Never disassemble or modify the apparatus in any way.

• Versuchen Sie niemals das Gerät auseinander zu nehmen

oder auf jegliche Art zu verändern.

• Ne jamais démonter ou modiﬁer l’appareil d’une manière ou

d’une autre.

• Non smontate mai, né modiﬁcate l’unità in nessun modo.

• Nunca desarme o modiﬁque el equipo de ninguna manera.

• Nocit dit apparaat demonteren of op andere wijze

modiﬁeren.

• Plaats geen voorwerpen gevuld met water, bijvoorbeeld een vaas, op het apparaat.

* (For apparatuses with ventilation holes)

OBSERVERA:

• Do not obstruct the ventilation holes.

• Die Belüftungsöffnungen dürfen nicht verdeckt werden.

• Ne pas obstruer les trous d’aération.

• Ventilationen bör inte förhindras genom att täcka för ventilationsöppningarna med föremål

såsom tidningar, bordsdukar, gardiner osv.

• Inga blottade brandkällor, såsom tända ljus, bör placeras på apparaten.

• Tänk på miljöaspekterna när du bortskaffar batteri.

• Apparaten får inte utsättas för vätska.

• Non coprite i fori di ventilazione.

• No obstruya los oriﬁcios de ventilación.

• De ventilatieopeningen mogen niet worden beblokkeerd.

• Täpp inte till ventilationsöppningarna.

• Hantera nätkabeln varsamt.

Håll i kabeln när den kopplas från el-uttaget.

• Inga objekt med vätskor,såsom vaser, får placeras på apparaten.

• Ta inte isär apparaten och försök inte bygga om den.

ENGELNISGHLISH

Contents

Before Using

Getting Started

Cautions on Installation

Accessories······················································································1

Before Using····················································································1

Cautions on Installation··································································1

Acoustic Sponge············································································2

How to Install·················································································2

Cleaning ·························································································2

Other Cautions···············································································2

The quality of the sound produced from the speaker is affected by the

size and type of the room, as well as by the method of installation.

Consider the points listed below before installing the speaker.

Thank you for purchasing this DENON product. To ensure proper

operation, please read this owner’s manual carefully before using the

product.

• If the bass sound is overemphasized when the speakers are installed

directly on the ﬂoor, set them on concrete blocks or other hard

stands.

After reading them, be sure to keep them for future reference.

Accessories

Check that the following parts are attached in addition to the main

unit:

• Note that placing the speaker on the same stand or shelf as a record

player may result in howling.

Connections

Connections ····················································································3

• Also note that if there is a magnet or any device generating magnetic

force nearby, interaction between this device and the speakers can

cause the colors on theTV to become blotchy.

q Owner’s Manual ......................................................................1

w Service station list...................................................................1

e Speaker cable (Approx. 9.8 ft / 3 m) ........................................2

r Foam plug................................................................................2

t Anti-slip pads (8 pcs. / 1sheet) ................................................1

Removing the Speaker Net··························································· 3

WARNING

Speciﬁcations················································································· 4

• Fasten the speaker cables to the wall, etc., to avoid catching them on

your hands or feet and causing the unit to fall.

• Be sure to check for safety after installing the speakers. Afterwards,

perform safety inspections at regular intervals to make sure there at

the speakers will fall.

DENON will accept no responsibility for damages or accidents

caused by inappropriate choice of the place of installation or improper

installation procedures.

[Rear]

[

]

Front

Note that the illustrations in this instructions may differ from the actual

set for explanation purposes.

ENGELNISGHLISH

Acoustic Sponge

How to Install

Cleaning

Attach four of the included anti-slip pads to the bottom of the unit as • Use a wiping cloth and wipe lightly to remove dirt from the cabinet

When installing on a desktop or in the corner of your room, the bass

may emphasized. Insert sound foam plug in the bass-reﬂex duct at the

back of the SC-M37.

You can adjust the bass sound with the amount of sound foam plug

you insert.

shown on the diagram below.

and operation panel.

※ When using chemically treated cloths, follow the precautions that

have been written for them.

• Donotusebenzene, thinners, orotherorganicsolventsorinsecticides

on the main unit since they may cause a change in quality or color.

[Bottom]

Other Cautions

Anti-slip pads

• Raising the ampliﬁer’s volume excessively and playing with distorted

sound could damage the ampliﬁer and speakers. Enjoy the sound at

a reasonable volume level.

• When moving the unit, note that applying strong force to the surface

of the speaker through the saran net could damage the speaker.

Foam plug

CAUTION

• Do not insert the foam plug too deep.The foam plug could fall in and

get stuck inside.

• If the foam plug cannot be removed or falls inside, stop using the

unit immediately and consult your store of purchase or your nearest

repair and inquiry center.

ENGLISH

Connections

Use the included speaker cable to connect the input terminals on the

back of the speakers to the ampliﬁer’s speaker output terminals.

Connections

Removing the Speaker Net

• The net on the front of the speakers can be removed.

• To remove, grasp both sides of the net and pull forward.

• To mount, line up the projecting pieces in the four corners of the

speaker net with the holes in the four corners of the cabinet and

press in.

When connecting, be sure to read the ampliﬁer’s owner’s manual

carefully and connect properly.

• Connect the input terminals on the rear panel of the speaker with the

speaker output terminals on the ampliﬁer, using the speaker cables

(Supplied).

“+” side terminal: Red

“–” side

terminal: Black

• Connect the speaker for the left channel to the “L” terminal on the

ampliﬁer, the speaker for the right channel to the “R” terminal on the

ampliﬁer, making sure to check the polarities (“+” and “–”).

• There are various types of speaker output terminals on ampliﬁers.

Check your ampliﬁer’s owner’s manual.

Connect to ampliﬁer’s

“+”side: Plain core

CAUTION

Connect to ampliﬁer’s

“–” side: Striped core

• Be sure to turn the ampliﬁer’s power off before connecting the

speakers to the ampliﬁer.

• If the polarities are inverted, the phase may be off and the sound

may have no bass component, making it seem unnatural. Be sure to

connect the polarities properly.

ꢀTwistꢀﬁrmlyꢀtheꢀwiresꢀbyꢀhandꢀsoꢀ

thatꢀtheyꢀdoꢀnotꢀstickꢀoutꢀandꢀcauseꢀ

short-circuits.

Sheath

ꢀLoosenꢀtheꢀterminalꢀbyꢀturningꢀtoꢀtheꢀleftꢀandꢀinsertꢀ

theꢀ speakerꢀ cableꢀ throughꢀ theꢀ holeꢀ inꢀ theꢀ speakerꢀ

terminal.

Tightenꢀtheꢀterminalꢀbyꢀturningꢀtoꢀtheꢀrightꢀandꢀcheckꢀ

thatꢀtheꢀcoreꢀwireꢀisꢀnotꢀprotrudingꢀfromꢀtheꢀhole.

Once connections are completed, pull gently on the speaker cables to

check that they are securely connected.

CAUTION

Do not let the core wires of two speaker cables touch each other.

Doing so will short-circuit the ampliﬁer circuitry and damage the

ampliﬁer.

ENGLISH

Speciﬁcations

Type:

2-way · 2-speakers

Low-leakage-ﬂux, Reﬂex box

45 Hz ~ 40 kHz

6 Ω/ohms

60 W (IEC), 120 W (PEAK)

86 dB (1 W · 1 m)

Frequency range:

Input impedance:

Max. input:

Sensitivity:

Crossover frequency:

Speakers:

3 kHz

12 cm (4-3/4”) cone bass-mid x 1

2.5 cm (1”) soft dome high range x 1

145 (W) x 233 (H) x 234 (D) mm

(5-45/64” x 9-11/64” x 9-7/32”)

3.8 kg (8 lbs 6 oz)

Maximum external dimensions:

Weight:

b For improvement purposes, speciﬁcations and design are subject to change without notice.

www.denon.com

Denon Brand Company, D&M Holdings Inc.

Printed in China 5411 10061 007D

Nokia 5180 User Manual
Nokia 2125i User Manual
Motorola VU204 User Manual
Motorola TRUE User Manual
Miele 07 173 930 User Manual
Maxtor OneTouch STM307504OTB3E1 RK User Manual
Denon PMD330 User Manual
Clarion DXZ725 User Manual
Centon electronic DataStick Bolt 16GBDSB SILVER User Manual
Analog Devices High Efficiency Synchronous Step Down Switching Regulators ADP1148 User Manual