Denon DVD 1940CI User Manual

DVD AUDIO-VIDEO / SUPER AUDIO CD PLAYER

DVD-1940CI

PRECAUTIONS

Laser Safety

This unit employs a laser. Only a qualified service person should remove the cover or attempt to service

this device, due to possible eye injury.

CAUTION:

LOCATION:

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECI-

FIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO

BEAM.

INSIDE, NEAR THE DECK MECHANISM.

FCC WARNING- This equipment may generate or use radio frequency energy. Changes or modifications

to this equipment may cause harmful interference unless the modifications are expressly approved in the

manual. The user could lose the authority to operate this equipment if an unauthorized change or

modification is made.

RADIO-TV INTERFERENCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the equipment and receiver.

3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

CAUTION:TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

Non-use periods - Turn off the unit when it is not in use. Unplug the unit from the household AC outlet if it is

not to be used for a long time. Unplug the unit during lightning storms.

Please read this operating instructions carefully before using your DVD player, and keep it for future reference.

Important

Use only discs marked with logos listed on page 6.

Cautions on Installation

Noise or disturbance of the picture may be generated if this

unit or any other electronic equipment using microproces-

sors is used near a tuner or TV.

Power Supply

The main power supply is engaged when the main plug is

plugged in a 120V, 60Hz AC outlet. To operate the unit, press

the ON/STANDBY button to turn on the unit.

If this happens, take the following steps:

• Install this unit as far as possible from the tuner or TV.

• Set the antenna wires from the tuner or TV away from this

unit’s power cord and input/output connection cords.

Noise or disturbance tends to occur particularly when using

indoor antennas or 300Ω/ohms feeder wires. We recommend

using outdoor antennas and 75Ω/ohms coaxial cables.

Warning

•

To avoid fire or electric shock, do not expose this unit to rain

or moisture.

NOTE:

WARNING:

LIVE PARTS INSIDE.

DO NOT REMOVE ANY SCREWS.

• For heat dispersal, do not install this equipment in a con-

fined space such as a book case or similar unit.

10 cm or more

Installation Location

For safety and optimum performance of this unit:

•

Do not stand the unit up vertically. Install the unit in a hori-

zontal and stable position. Do not place anything directly on

top of the unit. Do not place the unit directly on top of the TV.

Shield it from direct sunlight and keep it away from sources

of intense heat. Avoid dusty or humid places. Avoid places

with insufficient ventilation for proper heat dissipation. Do not

block the ventilation holes on the sides of the unit. Avoid

locations subject to strong vibration or strong magnetic fields.

•

Wall

• Be sure to remove a disc and unplug the AC power cord

from the outlet before carrying the unit.

–

PRECAUTIONS

Dew Warning

Moisture condensation may occur inside the unit when it is

moved from a cold place to a warm place, or after heating a

cold room or under conditions of high humidity. Do not use the

DVD Player at least for 2 hours until its inside is dry.

cabinet slot as they could touch current carrying parts or

short circuit parts resulting in a fire or electric shock.

6) Never spill liquid of any kind on this unit.

If liquid is spilled into the unit, consult qualified service engineer.

7) Use this unit in a horizontal (flat) position only.

8) This equipment is in Stand-by mode when it turns off

whilst the power cord is connected.

9) Keep the set free from moisture,water and dust.

10) Sufficiently ventilate the place of installation. If the unit is left in

a room full of the smoke from cigarettes, etc., for long periods

of time, the surface of the optical pickup could get dirty, in

which case it will not be able to read the signals properly.

11) Store the operating instructions in a safe place. After

reading the operating instructions, store them in a safe

place as they could come in handy in the future.

12) Handle the power cord carefully. Hold the plug when

unplugging the cord.

13) All the safety cautions and operating instructions should

be read before the DVD player is operated.

14) Use caution not to pinch your finger in the disc slot.

15) Do not put heavy objects on the AC power cord.

16) Keep the AC power cord away from heat appliances.

17) Be sure to remove a disc and unplug the AC power cord

from the outlet before carrying the DVD player.

Avoid the Hazards of Electrical Shock and Fire

• Do not handle the power cord with wet hands.

• Do not pull on the power cord when disconnecting it from

AC wall outlet. Grasp it by the plug.

• If, by accident, water is spilled on this unit, unplug the

power cord immediately and take the unit to our Authorized

Service Center for servicing.

Caution

1) Do not attempt to open the cabinet. There are no parts you can

service inside. Refer all servicing to qualified service personnel.

2) Slot and openings in the cabinet and at the side or bottom

are provided for ventilation. To ensure reliable operation

and to protect the unit from overheating these opening

must not be blocked or covered. Avoid enclosed spaces

such as book cases unless proper ventilation is provided.

3) Keep the unit away from the radiator heat sources.

4) Avoid using near strong magnetic fields.

18) Do not put any pressure to the DVD player when carrying.

19) Do not use the DVD player outdoors.

5) Do not push objects of any kind into this through the

TABLE OF CONTENTS

■

IMPORTANT SAFEGUARDS . . . . . . . . . . . . . . . . . . . . 2

PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Laser Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Important . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Cautions on Installation . . . . . . . . . . . . . . . . . . . . . . . . . 3

Dew Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Avoid the Hazards of Electrical Shock and Fire . . . . . . . 4

Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

About Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Notice for the Progressive Scan Outputs . . . . . . . . . . . . 5

Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Symbols Used in this Manual. . . . . . . . . . . . . . . . . . . . . 5

ABOUT THE DISCS . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Playable Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

FUNCTIONAL OVERVIEW . . . . . . . . . . . . . . . . . . . . . . 8

FRONT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

REMOTE CONTROL . . . . . . . . . . . . . . . . . . . . . . . . . 8

Tour of the Remote Control . . . . . . . . . . . . . . . . . . . . . . 9

Front Panel Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Displays during Operation . . . . . . . . . . . . . . . . . . . . . . 11

Loading the Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . 11

Using a Remote Control . . . . . . . . . . . . . . . . . . . . . . . 11

CONNECTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Description - Rear Panel . . . . . . . . . . . . . . . . . . . . . . . 12

Connection to an Audio System. . . . . . . . . . . . . . . . . . 13

Connection to 5.1-channel Surround Sound System. . . 14

Connection to a TV (for video) . . . . . . . . . . . . . . . . . . . 15

Connection to a TV with an HDMI Compatible Port . . . 16

Connecting the AC Cord . . . . . . . . . . . . . . . . . . . . . . . 16

DISC PLAYBACK . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Basic Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

HDMI Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Pure Direct Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Brightness of the Front Panel Display. . . . . . . . . . . . . . 17

TV TYPE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

General Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Disc Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Title Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

CALLING UP A MENU SCREEN DURING PLAYBACK. . 18

DVD Audio Playback . . . . . . . . . . . . . . . . . . . . . . . . . . 18

PLAYBACK OF ALL GROUPS . . . . . . . . . . . . . . . . . 18

PLAYBACK FROM A DESIRED GROUP . . . . . . . . . 18

PAGE SELECTION . . . . . . . . . . . . . . . . . . . . . . . . . 18

PLAYBACK OF THE BONUS GROUP . . . . . . . . . . . 18

Still / Pause . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Resume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Fast Forward / Reverse Search . . . . . . . . . . . . . . . . . . 18

Slow Forward / Slow Reverse . . . . . . . . . . . . . . . . . . . 19

Step by Step Playback. . . . . . . . . . . . . . . . . . . . . . . . . 19

Zoom. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Title / Chapter Search . . . . . . . . . . . . . . . . . . . . . . . . . 19

BY USING THE SEARCH MODE BUTTON . . . . . . . 19

. . . . . . . . 19

USING THE SKIP BUTTONS

Track Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

BY USING THE SEARCH MODE BUTTON . . . . . . . 19

. . . . . . . . 19

USING THE SKIP BUTTONS

■

Time Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Marker Setup Screen. . . . . . . . . . . . . . . . . . . . . . . . . . 20

Repeat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

REPEAT TITLE / CHAPTER. . . . . . . . . . . . . . . . . . . 20

REPEAT TRACK / GROUP / ALL . . . . . . . . . . . . . . . 20

A-B REPEAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Program Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Random Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

MP3 / JPEG / WMA Playback . . . . . . . . . . . . . . . . . . . 22

DivX^®Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

DivX^®Subtitle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Changing the On-Screen Display . . . . . . . . . . . . . . . . . 24

Slide Show Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Dialog Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Audio Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Subtitle Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Camera Angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Picture Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Sound Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Stereo Sound Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Super Audio CD Setup. . . . . . . . . . . . . . . . . . . . . . . . . 27

Virtual Surround . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Black Level Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

DVD SETUP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Language Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Display Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Audio Setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Speaker Setting for ANALOG AUDIO. . . . . . . . . . . . . . 30

Speaker Setting for HDMI AUDIO . . . . . . . . . . . . . . . . 31

Ratings Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

RATING LEVEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

IF YOU FORGET THE PASSWORD . . . . . . . . . . . . . 31

CONTROL LEVELS. . . . . . . . . . . . . . . . . . . . . . . . . 31

Others Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Reset to the Default Settings (except for Ratings Control) . . 32

Language Code List . . . . . . . . . . . . . . . . . . . . . . . . . . 32

TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . 33

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

■

–

INTRODUCTION

The serial number of this product may be found on the back of the DVD player. No others have the same serial

number as yours. You should record the number and other vital information here and retain this book as a per-

manent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.

Date of Purchase

Dealer Purchase from

Dealer Address

Dealer Phone No.

Model No.

Serial No.

About Copyright

Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual

property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended

for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering

or disassembly is prohibited.

U. S. Patent Nos, 4,631,603, 4,819,098, 4,907,093, 5,315,448 and 6,516,132.

Notice for the Progressive Scan Outputs

Consumers should note that not all high definition television sets are fully compatible with this product and may

cause artifacts to be displayed in the picture. In case of picture problems with 480 (525) or 576 (625) progres-

sive scan output, it is recommended that the user switch the connection to the ‘standard definition’ output. If

there are questions regarding your TV set compatibility with this 480p (525p) or 576p (625p) DVD player, please

contact our customer service center.

Supplied Accessories

Please check to make sure the following items are included with the main unit in the carton.

“AA” (R6P)

batteries

Operating

Instructions Station

• • • • • • • •

Service

Audio

cable

Warranty

Video

cable

AC cord

• • • • • • •

Remote

control

• • • •

• • •

• •

Card

• •

• • • • • • • •

List

• • • •

Symbols Used in this Manual

The following symbols appear below in some headings and notes in this manual, with the following meanings.

Description refers to playback of DVD-

Video discs. (including DVD-R/RW discs)

Description refers to playback of discs for-

matted with MP3.

DVD-V

DVD-A

MP3

JPEG

WMA

Description refers to playback of DVD-

Audio discs.

Description refers to viewing of JPEG

discs.

Description refers to playback of Audio

CDs.

Description refers to playback of discs for-

matted with WMA.

Super

Description refers to playback of Super

Audio CDs.

Description refers to playback of discs for-

matted with DivX^®.

Audio CD

DivX

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your

local recycling regulations.

Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning

chemical wastes.

Make your contribution to the environment!!!

• Used up batteries do not belong in the dust bin.

• You can dispose of them at a collection point for used up batteries or special waste. Contact your council for details.

–

ABOUT THE DISCS

Playable Discs

Playable

discs

Recorded

signals

Mark (logo)

Region code

Disc size

Disc types

Digital audio

Digital video

(MPEG2)

Example

12 cm

8 cm

Group 1

Group 2

DVD-Audio

* 1, 2, 4

Track 1

Track 3

Track 2

Track 4

Track 1

Track 2

Example

Title 1

Title 2

DVD-Video

* 1, 2, 4

Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1

Chapter 2

Digital video

(MPEG2)

MP3,

Digital picture

(JPEG),

MP3,

JPEG,

WMA,

DivX^®

12 cm

8 cm

DVD-R

DVD-RW

* 1, 2, 3, 4,

5, 6, 7, 8

Example

GROUP 1

GROUP 2

WMA*8,

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

DivX^®

(DVD-R/RW only)

Super

Audio CD

Super Audio CD

Digital audio

* 2, 4

Audio CD

Example

Audio CD

* 2, 4

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

12 cm

8 cm

Digital audio

MP3

WMA*8

CD-R

CD-RW

* 2, 3, 4, 6,

7, 8

MP3,

JPEG,

WMA,

DivX^®

Digital picture

(JPEG)

DivX^®

Example

GROUP 1

GROUP 2

Picture CD

* 2, 3, 4, 6,

Track 1

Track 2

Track 3

Track 4

Track 5

Track 6

JPEG

12 cm

is a trademark of DVD Format/Logo Licensing Corporation.

is trademark of Eastman Kodak Company.

DivX, DivX Ultra Certified, and associated logos are trademarks of DivX, Inc.and are

used under license.

If you cannot play back a disc which bears one of the marks above, check the following notes.

*1: Certain DVD discs do not operate as described in this manual due to the intentions of the disc’s producers.

*2: Scratched or stained discs may not be played back.

*3: Some discs cannot be played back because of incompatible recording conditions, characteristics of the

recorder or special properties of discs.

*4:You can play back discs which bear the marks above. If you use nonstandardized discs, this unit may not

play them back. Even if they are played back, the sound or video quality will be compromised.

*5: Only the discs recorded in the video format and finalized can be played back. Unfinalized discs cannot be

played back. Depending on the recording status of a disc, the disc may not be played back at all or normal-

ly (the picture or sound may be distorted, etc.).

*6: If there is too much recordable space left on a disc (the used portion is less than 2-3/16 inches (55mm

across)), it may not be played back properly.

*7: Do not glue paper or put stickers on to the disc. These may damage the disc, and the unit may not read it

correctly.

*8: This player cannot play back the disc contents protected by Windows Media Digital Rights Management

(DRM).

¡ NEVER play back the following discs. Otherwise, malfunction may result!

DVD-RAM / CD-i / Photo CD / Video CD / DVD with region codes other than 1 or ALL / DVD-ROM for per-

sonal computers / CD-ROM for personal computers

• Any other discs without compatibility indications

CAUTION:

• Use caution not to pinch your finger in the disc slot.

• Be sure to remove a disc and unplug the AC power cord from the outlet before carrying the DVD player.

–

FEATURES

¡Progressive Scan system

¡On-screen display

The progressive scan system provides less flickering and

images in higher resolution than that of traditional 480i

(525i), 576i (625i) or multi television signals through the

interlace scan system.

Information about the current operation can be displayed on a

TV screen, allowing you to confirm the currently active func-

tions (such as program playback) using the remote control.

¡Dimmer

TV Type

The brightness of the front panel display can be adjusted.

Use this to set your TV’s video format (MULTI, NTSC or PAL).

¡Screen Saver

Analog 5.1-channel Dolby and DTS surround output

The screen saver program starts if there is no activity at

the player or its remote for more than 5 minutes. The

brightness of the display is darken by 75%. The program is

deactivated when there is any activity.

This player is equipped with analog 5.1-channel Dolby and

DTS surround audio out jacks for playback.

¡HDMI (High-Definition Multimedia Interface)

You can enjoy clearer video output when connecting this

player to a display equipment with an HDMI-compatible port.

¡Picture Control

Picture Control adjusts Brightness, Contrast, Color, Gamma

Correction and Sharpness of the specific display.

¡Dialog Speed

¡Search

Playback in slightly faster or slower speed while keeping

the sound quality as in the normal playback.

Dialog speed is available only on discs recorded in the

Dolby Digital format.

Chapter search: Search for a desired chapter.

Title search:

Search for a desired title.

Group search: Search for a desired group.

Page search:

Track search:

Time search:

Search for a desired page.

Search for a desired track.

Search for a desired time point or a title

or a track.

¡Still/Fast/Slow/Step playback

Various playback modes are available including still pictures,

fast forward/reverse, slow motion and step frames.

¡Still Mode

¡Repeat

The resolution of pictures while in the still (pause) mode

can be adjusted.

Chapter :Repeated playback of a chapter of the disc.

Title :

Repeated playback of a title of the disc.

Track : Repeated playback of a track of the disc.

¡Random Playback for Audio CD, Super Audio

All :

Repeated playback of the entire disc.

(exclude DVD-Video)

Repeated playback of a part between two points.

CD, MP3, JPEG, DVD-Audio and WMA

This player can shuffle the playback order of tracks in

random order.

A-B :

Group : Repeated playback of a folder of the

DVD-Audio/MP3/JPEG/WMA/DivX^®disc being

played is possible.

¡Program Playback for Audio CD, Super Audio

CD, MP3, JPEG, DVD-Audio and WMA

You can program the playback order of tracks in a desired

order.

¡Zoom

2-time or 4-time magnified image can be displayed.

¡DVD menus in a desired language

You can display DVD menus in a desired language, if

available on a DVD.

¡Marker

Electric reference points designated by user can be called back.

¡Resume Playback

¡Auto Power Off

User can resume playback from the point at which the

playback has been stopped even if the power is turned off.

The power turns off automatically if there is no activity at

the player or its remote for more than 30 minutes (refer to

page 31).

¡COMPONENT VIDEO OUT Jacks

Jacks located on the back of the DVD Player which are

used to send high-quality video to a TV via Component

Video In Jacks.

¡Subtitles in a desired language

You can select a desired language for subtitles if that

language is available on the DVD and DivX^®.

¡Bit rate indication

¡Selecting a camera angle

You can select a desired camera angle if a disc

contains sequences recorded from different angles.

¡DRC (Dynamic Range Control)

You can control the range of sound volume.

¡Displaying a JPEG picture

Kodak Picture CDs can be played back. Still images stored in

JPEG format on DVD-R/RW or CD-R/RW can also be played back.

¡Choices for audio language and sound mode

You can select a desired audio language and sound mode if

different languages and modes are available on a disc.

¡Reproducing WMA data

You can enjoy WMA files which are recorded on DVD-R/RW or

CD-R/RW.

¡Ratings Control (Parental lock)

You can set the control level to limit playback of discs

which may not be suitable for children.

¡Playing back an MP3 disc

Super Audio CD multi-channel playback compatibility

You can enjoy MP3 files which are recorded on DVD-R/RW or

CD-R/RW.

In addition to playing DVD-Video and DVD-Audio discs,

this player can play multi-channel Super Audio CDs and a

maximum of 5.1 channels can be output.

¡Reproducing DivX data

You can enjoy DivX^®files which are recorded on

DVD-R/RW or CD-R/RW.

¡Automatic detection of discs

This player automatically detects if a loaded disc is

DVD-Video, DVD-Audio, Audio CD, Super Audio CD, MP3,

JPEG, WMA or DivX^®.

• Official DivX^®Ultra Certified product

• Plays all versions of DivX^®video (including DivX^®6) with

enhanced playback of DivX^®media files and the DivX

Media Format.

¡Pure Direct

The sound quality of analog audio output is improved by

turning off HDMI output, video signal output, and the front

panel display.

“WMA” (Windows Media Audio) is an audio

codec developed by Microsoft in the United

¡Direct Search

You can search the desired title, chapter, and track with

numeric button during playback or in stop mode.

States of America.

–

FUNCTIONAL OVERVIEW

FRONT PANEL

6/25

4 5 7/29

REMOTE CONTROL

1. ON/STANDBY (POWER ON/OFF) Buttons [page 17]

2. Disc loading tray

3. OPEN/CLOSE Button [page 17]

4. PLAY Button [page 17]

5. STOP Button [page 17]

6. H (SKIP DOWN) Button [page 19]

7. G (SKIP UP) Button [page 19]

8. DIMMER NTSC/PAL Button [page 17]

9. PURE DIRECT Button [page 17]

Press to activate Pure Direct function to reduce noise

level.

10. HDMI Button [page 17]

Press to set the HDMI connector’s video signal output

mode.

11. STILL/PAUSE Button [page 18]

12. Display, Remote Sensor Window

13. HDMI indicator [page 17]

Lights up when there is video signal output from the

HDMI OUT jack.

14. A-B REPEAT Button [page 20]

15. REPEAT Button [page 20]

16. RANDOM Button [pages 21]

17. ZOOM Button [page 19]

18. CLEAR Button [page 19]

19. ANGLE Button [page 26]

20. MENU Button [page 18]

21. ENTER Button [page 17]

22. Cursor Buttons [page 17]

23. RETURN Button [page 20]

24. SEARCH MODE Button [page 19]

25. h (Fast Reverse SEARCH) Button [page 18]

Press more than 2 seconds when you use the front

panel button for this function.

26. GROUP Button [page 18]

27. SUPER AUDIO CD SET UP Button [page 27]

28. PAGE Buttons [page 18]

29. g (Fast Forward SEARCH) Button [page 18]

Press more than 2 seconds when you use the front

panel button for this function.

30. SETUP Button [page 28]

31. SUBTITLE Button [page 26]

32. TOP MENU Button [page 18]

33. DISPLAY Button [page 24]

34. AUDIO Button [page 26]

35. Numeric Buttons [page 17]

36. MODE Button [page 21]

The buttons with circled numbers can only be

operated with the remote control.

–

FUNCTIONAL OVERVIEW

Tour of the Remote Control

Buttons on remote control work in different ways for DVD-Video, DVD-Audio, Audio CD, Super Audio CD, MP3, JPEG, WMA

and DivX^®: Refer to the following table for correct use.

CD, Supper Audio CD,

MP3, JPEG, WMA

DivX^®

DVD-Video, DVD-Audio

POWER ON/OFF Buttons

• To turn on or standby the unit.

A-B REPEAT Button

• To mark a segment between

A and B for repeated playback.

(CD, Super Audio CD)

• To mark a segment between

A and B for repeated playback.

• To mark a segment between

A and B for repeated playback.

• To repeat playback of a

track or disc.

• To repeat playback of a track,

group or disc. (DivX^®media files)

• To repeat playback of a

title or chapter.

REPEAT Button

RANDOM Button

(CD, Super Audio CD)

• To repeat playback of a

track, group, or disc.

(MP3, JPEG, WMA)

• To repeat playback of a title,

chapter, group or track.

(DivX^®video files)

• To shuffle the playing order of

groups and tracks.

(DVD-Audio)

• To play back tracks in

random order.

• To set Picture Control.

• To set Black Level on/off.

• To activate the 3D sound

(Virtual surround system).

• To set Dialog Speed.

• To program a specific

playback order. (DVD-Audio)

• To play all groups. (DVD-Audio)

• To program a specific

playback order.

MODE Button

• To activate the 3D sound

(Virtual surround system).

(CD, MP3, WMA)

• To set Picture Control.

• To set Black Level on/off.

• To activate the Slide Show mode.

(JPEG)

ZOOM Button

ANGLE Button

SUBTITLE Button

AUDIO Button

• To magnify part of the picture

(x2/x4).

• To magnify part of the picture (x2).

(JPEG)

• To magnify part of the picture (x2).

• To select a camera angles

on the disc.

• To rotate a picture. (JPEG)

• To select a subtitle language

on the disc.

• To select a subtitle language

on the disc.

• To access various audio functions

on the disc.

• To access various audio functions

on the disc.

• To select STEREO, L-ch or R-ch.

(CD)

DISPLAY Button

• To display the current disc

or HDMI mode.

• To display the current disc

or HDMI mode.

• To display the current disc

or HDMI mode.

• To search for a track.

• To search for time or a

marker. (CD, Super Audio CD)

• To rapidly return to a location

on the disc. (CD, Super Audio CD)

• To search for a track, or time.

(DivX^®media files)

• To search for a title, chapter,

track, time or marker.

SEARCH MODE Button

• To search for a chapter, title or

time. (DivX^®video files)

• To rapidly return to a location

on the disc.

OPEN/CLOSE Button

Numeric Buttons

• To open or close the disc tray.

• To select a track directly.

(DivX^®media files)

• To select a title, chapter, group

or track directly.

• To select a track directly.

• To select a chapter or title directly.

(DivX^®video files)

• To clear the markers.

(CD, Super Audio CD)

• To clear the markers.

• To clear the most recently entered

track for the program playback.

(DVD-Audio)

• To clear the numbers entered

incorrectly.

CLEAR Button

• To clear the most recently entered

track for the program playback.

• To clear the numbers entered

incorrectly.

• To cancel the point for A-B Repeat.

(CD, Super Audio CD)

• To clear the numbers entered

incorrectly.

• To cancel the point for A-B Repeat.

–

FUNCTIONAL OVERVIEW

Tour of the Remote Control

CD, Supper Audio CD,

MP3, JPEG, WMA

DivX^®

DVD-Video, DVD-Audio

MENU Button

TOP MENU Button

ENTER, Cursor Buttons

• To call up the file list.

(MP3, JPEG, WMA)

• To call up the file list.

• To call up the menu on a disc.

• To call up the menu on a file.

(DivX^®video files)

• To return to the top file in the

highest hierarchy of the file list.

• To return to the top file in the

highest hierarchy of the file list.

(MP3, JPEG, WMA)

• To call up the top menu on a disc.

• To move the cursor and determine • To move the cursor and determine • To move the cursor and determine

its position.

RETURN Button

• To return to the previous operation

in the setup menu.

• To return to the previous operation

in the setup menu.

• To return to the previous

operation in the setup menu.

SETUP Button

SKIP Buttons

• To call up the setup menu.

• To skip titles/chapters/tracks.

• To call up the setup menu.

• To skip tracks.

• To call up the setup menu.

• To skip tracks. (DivX^®media files)

• To skip chapters. (DivX^®video files)

SEARCH Buttons

• To search forward/backward

through a disc.

• To begin slow forward.

• To search forward/backward

through a disc.

(except JPEG)

• To search forward/backward

through a disc.

• To begin slow forward/slow reverse.

STOP Button

PLAY Button

• To stop playback.

• To begin playback.

• To stop playback.

• To begin playback.

• To pause playback.

• To stop playback.

• To begin playback.

STILL/PAUSE Button

• To pause playback.

• To advance playback frame

by frame.

• To pause playback.

• To advance playback frame

by frame.

GROUP Button

• To begin playback from a desired

group. (DVD-Audio)

SUPER AUDIO CD

SET UP Button

•

To select the Super Audio CD setup.

(Super Audio CD)

PAGE Buttons

• To select a desired background

display image for playback.

(DVD-Audio)

Front Panel Display

Lights up when the progressive scan system is activated.

Displays a type of the disc which is on the tray.

• DVD: DVD-Video, MP3, JPEG, WMA, DivX^®on DVD-R/RW

• DVD A: DVD-Audio

Lights up when the disc playback comes to a pause.

Lights up when playing back in slow mode.

(DVD, DivX^®)

• CD: Audio CD, MP3, JPEG, WMA, DivX^®on CD-R/RW

Lights up when the repeat function is on.

Lights up when the inserted disc is being play back.

SACD: Super Audio CD

The present display state is shown.

• TL./GR.: Title or Group

Lights up when the ALL repeat function is on.

Lights up when the A-B repeat function is on.

SACD

• TR./CP.: Track or Chapter

To change to the display of a title press the

DISPLAY button in the state of Resume.

Lights up when you have selected the audio file

(CD/MP3/WMA/DVD-Audio) on the program screen.

Displays the chapter (title) or track

number. In case the chapter (title) or

track number is over 100, displays

“- -”.

Displays the elapsed time of the chapter (title) or

track. (The display of 10 hours or more cannot be

performed.) Selected HDMI output mode is displayed.

–

FUNCTIONAL OVERVIEW

Displays during Operation

Power on

Loading the Batteries

1. Open the battery compartment cover.

Power off

2. Insert two “AA” (R6P) batteries, with each

one oriented correctly.

Tray open

Tray closed

3. Close the cover.

Loading the Disc

No disc inserted or cannot

read

Cautions On Batteries

HDMI output mode

(480p/576p) is selected

(576p is displayed after

480p)

• Use “AA” (R6P) batteries in this remote control unit.

• Replace the batteries with new ones approximately once

a year, though this depends on the frequency with which

the remote control unit is used.

• If the remote control unit does not operate within a close

proximity of the main unit, replace the batteries with new

ones, even if less than a year has passed.

• The included batteries serve only for verifying operation.

Replace them with new batteries as soon as possible.

• When inserting the batteries, be careful to do so in the

HDMI output mode (720p) is

selected

HDMI output mode (1080i) is

selected

HDMI output mode (1080p)

is selected

proper direction, following the

remote control unit’s battery

compartment.

and

marks in the

HDMI output mode (OFF) is

selected

• To prevent damage or battery fluid leakage:

• Do not mix a new battery with an old one.

• Do not mix two different types of batteries such as

alkaline and manganese.

• Do not short-circuit, disassemble, heat or dispose of

batteries in flames.

Super Audio CD setup

(2CH AREA) selected

Super Audio CD setup

(MULTI-CH AREA) selected

• Remove the batteries when not planning to use the

remote control unit for a long period of time.

• If the batteries should leak, carefully wipe off the fluid

from the inside of the battery compartment, then insert

new batteries.

Program playback is set

Program playback setting

group (folder) is selected

Program playback setting

ALL CLEAR is selected

Using a Remote Control

Random playback is set

All group playback setting

Keep in mind the following when using the remote control:

• Make sure that there are no obstacles between the remote

control and the remote sensor on the unit.

• Remote operation may become unreliable if strong sunlight or

fluorescent light is shining on the remote sensor of the unit.

• Remote control for different devices can interfere with each

other. Avoid using remote control for other equipment locat-

ed close to the unit.

NOTES:

• The front panel display has blinked while setting the

program playback.

• “P**-●●●” is displayed in the front panel display while

setting the program playback. (“**” is program number,

“●●●” is track number.)

• “A” is displayed in front panel display while selecting the

audio file (CD, MP3, WMA, DVD-Audio).

• “F-***” is displayed in the front panel display while selecting

the group (folder). (“***” is group (folder) number.)

• “A-CLEAr” is displayed in the front panel display while

selecting ALL CLEAR.

• Replace the batteries when you notice a fall off in the oper-

ating range of the remote control.

• The maximum operable ranges from the unit are as follows.

- Line of sight:

approx. 23 feet (7m)

- Either side of the center: approx. 16 feet (5m) within 30˚

- Above:

- Below:

approx. 16 feet (5m) within 15˚

approx. 10 feet (3m) within 30˚

• “SHUFFLE” is displayed in the front panel display while

setting the random playback.

• “A-PLAY” is displayed on the front panel display while

setting the all group playback.

16 feet (5m)

30°

23 feet (7m) 16 feet (5m)

30°

–

CONNECTIONS

Description - Rear Panel

1. AC IN Terminal

Connects the AC cord to supply the power.

2. DIGITAL OUT Jacks (OPTICAL, COAXIAL)

Use either an optical or coaxial digital cable (commercially available) to connect to an AV amplifier with a built-in

decoder (AV control center).

3. HDMI OUT Jack

Use an HDMI connection cable (commercially available) to connect to a display with an HDMI compatible port.

4. AUDIO OUT Jacks

Connect to the Audio input jacks of A/V-compatible TV or wide screen TV or Stereo system.

5. VIDEO OUT Jack

Use a video cable to connect one of the jacks to Video input on your A/V-compatible TV or wide screen TV.

6. COMPONENT VIDEO OUT Jacks

Use a Component Video cable (commercially available) to connect these jacks if you have a TV with Component Video

in jacks. These jacks provide C /P , C /P and Y video. Along with S-Video, Component Video provides the best quality

picture.

7. S-VIDEO OUT Jack

Use the S-Video cable (commercially available) to connect this jack to the S-Video jack on your A/V-compatible TV or

wide screen TV for a higher quality picture.

8. REMOTE CONTROL IN/OUT Jacks

Connecting the DENON Satellite Remote Control to these jacks enables you to operate more than one DENON compo-

nents with one remote control.

9. CONTROL CONNECTOR (RS-232C)

This is a terminal for future system expansion.

10. 5.1ch AUDIO OUT Jacks

Use speaker cables (commercially available) to connect these jacks to the 5.1 ch Audio input jacks of your AV amplifier

with 5.1-channel input terminals.

When using the DENON Satellite Remote Control,

1. Connect the DENON Satellite Remote Control to the REMOTE CONTROL IN jack of this player. This allows you to oper-

ate this player with the Satellite Remote Control.

2. Connect another DENON component to the REMOTE CONTROL OUT jack of this player. This allows you to operate this

player and the connected component with the same Satellite Remote Control.

Selecting Progressive Scan (480p/576p or Interlaced 480i/576i) Playback

¡If your TV is compatible with progressive scanning (480p/576p), connect the TV to the COMPONENT VIDEO OUT jacks of

the DVD player and set PROGRESSIVE to ON in the display setting. Next, set your TV to the progressive scan mode.

Refer to page 28 for instructions on changing the display setting. P.SCAN will appear on the display of the unit.

¡If your TV is not compatible with progressive scanning, set PROGRESSIVE to OFF (refer to page 28). Make sure that P.SCAN

on the display of the unit lights off.

¡Use a commercially available adaptor if the video input jacks of your TV or monitor is the BNC type.

¡Progressive video signal will not be output from the COMPONENT VIDEO OUT while using the HDMI OUT jack.

What is Progressive Scanning?

¡Unlike conventional interlace scanning, the progressive scan system provides less flickering and images in higher resolution

than that of traditional (480i/576i) television signals.

The DCDi (Directional Correlational Deinterlacing) system of this DVD player produces smooth and

natural video images, even if really dynamic, by eliminating the jagged edges. *“DCDi” is a trademark

of Faroudja, a division of Genesis Microchip Inc.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks

of Dolby Laboratories.

“DTS” and “DTS Digital Surround” are registered trademarks of DTS, Inc.

–

CONNECTIONS

The following shows examples of connections commonly used to connect the DVD player to TV and other

components.

If using this DVD player to play back a DVD in a Dolby Digital Multi-channel surround or DTS surround format, the

DVD player outputs a Dolby Digital or DTS data stream from its OPTICAL or COAXIAL DIGITAL OUT jacks.

By hooking up the player to a Dolby Digital or DTS decoder, you can enjoy more convincing, realistic ambience

with powerful and high-quality surrounding sound of a professional standard which can be heard in movie theaters.

Use a commercially available audio optical or coaxial digital cable (not included) for the audio connections.

NOTES:

• Be sure to turn off the power of all components in the system before connecting another component.

• Refer to the Instruction Manuals for your TV, stereo system and any other components to be connected to the

DVD player.

Connection to an Audio System

Method 1

Method 2

AV amplifier with a built in decoder

(AV control center),

Dolby Digital decoder,

DTS decoder,

MD deck or DAT deck

Stereo system

Digital Audio Input

Jacks

Audio Input Jacks

AUDIO

Audio cable

(supplied)

Audio Coaxial

Digital cable

(commercially

available)

Optical cable

(commercially

available)

AUDIO OUT

(analog)

DIGITAL OUT

DVD

• Method 1 DVD Player + Stereo system

• Method 2 DVD Player + AV amplifier with a built in decoder (AV control center), Dolby Digital decoder, DTS decoder,

MD deck or DAT deck

NOTES (for Method 2 only):

• When using an AV amplifier with a built in decoder (AV control center), Dolby Digital, or DTS decoder as shown in the

Method 2, set DOLBY DIGITAL or DTS to BITSTREAM accordingly for audio output in the setup mode (refer to page 29).

Set it to PCM for the decoder that is not used currently. Playing back a DVD using incorrect settings may generate noise dis-

tortion, and may also damage the speakers.

• The audio source on a disc in a Dolby Digital Multi-channel surround format cannot be recorded as digital sound by an MD

deck or DAT deck.

•

Set DOLBY DIGITAL or DTS to PCM for audio output in the setup mode for connecting to an MD deck or DAT deck (refer to

page 29)

Harsh noise that could harm your ears or the speakers is generated when a DVD recorded in DTS is played while using a

decoder, etc., that is not DTS-compatible.

When playing back a copyright-protected 96kHz PCM DVD, the digital sound will be down sampled at 48kHz, even if you set

LPCM SELECT to OFF (refer to page 29).

Super Audio CD sound is not output from the DIGITAL OUT jacks.

Optical cable (commercially available)

• Optical cable (commercially available) may be damaged when bent at sharp angles. Ensure cables are coiled in loops with

a diameter of 6 inches (15cm) or more when storing them.

• Use a cable which is 9.8 feet (3m) or shorter.

• Insert cable plugs firmly into the connectors when making connections.

• If a plug has dust or is dirty, clean it with a soft cloth before inserting it into a connector.

–

CONNECTIONS

Connection to 5.1-channel Surround Sound System

Analog 5.1-channel audio signals can be output from the DVD player.

The multi-channel audio signals recorded in packed PCM and the multi-channel Super Audio CDs can be

played back when an AV amplifier equipped with analog 5.1-channel audio inputs is connected.

Center speaker

Front speaker

(left)

To 5.1-channel

Audio Input

Jacks

AUDIO

Front speaker

(right)

Subwoofer

Speaker

Cable

(commercially

available)

AV amplifier

with

5.1-channel

audio input jacks

Surround

speaker

(left)

Surround

speaker

(right)

5.1ch

AUDIO OUT

DVD

NOTES:

• For 5.1-channel connections, set ANALOG AUDIO to MULTI CHANNEL in the setup mode and adjust Speaker

Configuration, DELAY TIME and CHANNEL LEVEL settings (refer to page 30).

• You can enjoy high-quality analog sound by cutting off the video signal. Press the PURE DIRECT button on the front panel.

–

CONNECTIONS

Connection to a TV (for video)

Method 1

Method 2

Method 3

Basic

audio

Good

Better

Best picture

picture

COMPONENT

VIDEO IN

CR/PR

CB/PB

VIDEO IN

S-VIDEO IN

Audio

Cable

(supplied)

Video

Cable

(supplied)

S-Video

Component

Video

Cable

(commercially

available)

Cable

(commercially

available)

and

DVD

AUDIO OUT

(analog)

VIDEO OUT

S-VIDEO OUT

COMPONENT VIDEO OUT

• Method 1 DVD Player + TV with Video Input Jack

• Method 2 DVD Player + TV with S-Video Input Jack

• Method 3 DVD Player + TV with Component Video Input Jacks

NOTES:

• Connect the DVD player directly to a TV. If the Audio/Video cables are connected to a VCR, pictures may be distorted due

to the copy protection system.

• S-Video output connector

The video signals are divided into color (C) and brightness (Y) signals, achieving a clearer picture.

If the TV is equipped with a S-Video input connector, we recommend connecting it to this unit’s S-Video output connector

using a commercially available S-Video connection cord.

HOW TO CONNECT TO A TV WITHOUT AUDIO/VIDEO INPUT JACKS

If your TV does not have RCA type audio and video input jacks it is still possible to connect this DVD

player to your TV’s 75-ohm coaxial antenna terminal using an optional Stereo Audio/Video RF Modulator, not includ-

ed. Connect the audio and video outputs of the DVD player to the audio and video inputs on the RF Modulator, and

then connect the coaxial output of the RF Modulator (usually marked “TO TV”) to the 75 ohm coaxial antenna termi-

nal on your TV. Follow the instruction supplied with the RF Modulator for more details.

If your TV’s 75 ohm coaxial antenna terminal is already occupied by an antenna or cable box connection, remove that

cable from your TV’s antenna terminal and reconnect it to the coaxial antenna input terminal of the RF Modulator

(usually marked “ANT IN”), then connect the RF modulator to your TV’s antenna terminal as described above.

NOTE:

• The picture quality from DVD discs will not be as good if the DVD player is connected to the TV’s antenna terminal

through an RF Modulator.

–

CONNECTIONS

Connection to a TV with an HDMI Compatible Port

A simple 1-cable connection (using a commercially available cable) with a device having an HDMI (High-

Definition Multimedia Interface) connector allows digital transfer of the digital images of DVD-Video and other

sources, DVD-Video, and the multi-channel sound of DVD-Audio.

To HDMI Input

Connector

HDMI cable

A display equipment with an HDMI compatible port

(commercially available)

C Actual output modes by media

HDMI AUDIO Setting

2 CHANNEL

MULTI CHANNEL

DOLBY DIGITAL/DTS Setting

Audio Recording Format

Dolby Digital

DVD-Video DTS

BITSTREAM *1

Dolby Digital

DTS

PCM

BITSTREAM *1

Dolby Digital

DTS

PCM *2

2channel PCM

Multi PCM

LPCM

2channel PCM

Multi PCM

LPCM or PPCM

(with CPPM) *3 *5

LPCM or PPCM

(without CPPM)

Dolby Digital

MP3/MP2

2channel PCM

Multi PCM

DVD-Audio

DivX^®

2channel PCM

Multi PCM

Dolby Digital

2channel PCM

Dolby Digital

2channel PCM

Audio CD

MP3/WMA

MULTI-CH AREA *4

2CH AREA *4

CD AREA

Super

Audio

2channel PCM

*1 If the connected equipment is not compatible with HDMI BITSTREAM, signals are output on PCM.

*2 If the connected equipment is not compatible with HDMI Multi PCM, signals are output on down mixed PCM.

*3 If the connected equipment is not compatible with HDMI ver. 1.0, signals are not output.

*4 Sounds recorded on the MULTI-CH/2CH AREA of Super Audio CDs are not output.

*5 Transfer of signal from DVD audio discs that are copyright-protected by CPPM is only possible if both devices are HDMI Ver.1.1 compatible.

This player is HDMI Ver.1.3 compatible.

To play back the digital video images of a DVD via an HDMI connection, it is necessary that both the player and the display

equipment (or an AV amplifier) support a copyright protection system called HDCP (High-bandwidth Digital Content Protection

System). HDCP is copy protection technology that comprises data encryption and authentication of the connected AV equipment.

This player supports HDCP. Please read the operating instructions of your display equipment (or AV amplifier) for more

information.

*HDMI: High-Definition Multimedia Interface

NOTES:

• When using an HDMI-incompatible or HDCP-incompatible display equipment, the image will not be viewed properly.

• When the PURE DIRECT button on the front panel is turned on, not only HDMI images but sounds are not output (refer to

page 17).

• Among the devices that support HDMI, some devices can control other devices via the HDMI connector; however, this play-

er cannot be controlled by another device via the HDMI connector.

• The audio signals from the HDMI connector (including the sampling frequency, the number of channels and bit length) may

be limited by the equipment that is connected.

• When playing a Super Audio CD with an HDMI connection, audio cannot be transferred beyond the CD layer. Make an ana-

log connection for this.

• Among the monitors that support HDMI, some do not support audio output (for example, projectors). In connections with

equipment such as this, audio signals are not output from the HDMI output connector.

• When the set’s HDMI connector is connected to a DVI-D compatible monitor (HDCP compatible) with an HDMI-DVI convert-

er cable (commercially available), the signals are output in digital RGB.

“HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered

trademarks of HDMI Licensing LLC.”

Connecting the AC Cord

After you made all necessary connections, connect the AC cord to the AC inlet. Then connect the AC cord to

the AC outlet.

–

DISC PLAYBACK

Basic Playback

Pure Direct Mode

Super

Press the PURE DIRECT button on the front panel to

output an analog audio signal only (no analog video

and HDMI signals will be output and the display will be

turned off). The higher quality sound will be achieved.

DVD-V DVD-A CD

Audio CD

MP3

JPEG WMA DivX

Getting started

NOTES:

• Turn on the power of the TV, amplifier and any other com-

ponents which are connected to the DVD player.

• Make sure the TV and audio receiver (commercially avail-

able) are set to the correct channel.

• When the buttons below are pressed, the pure direct mode

will be released.

OPEN/CLOSE button (on both the remote and the front panel),

SETUP or DISPLAY button (on the remote), ON/STANDBY or

PURE DIRECT button (on the front panel).

Press the POWER ON button.

• “P-ON” will appear briefly on the display panel.

Press the OPEN/CLOSE button

to open disc loading tray.

• The PURE DIRECT button will not function while displaying

the setup menu.

• If you turn on the pure direct mode while selecting HDMI

mode, both video and audio signals will not be output.

Place the disc in the tray, with the

label facing up.

Brightness of the Front Panel Display

Press the PLAY button.

• The tray will close automatically,

Press the DIMMER NTSC/PAL button on the front

panel to select the desired brightness of the front

panel display. (BRIGHT, DIMMER or OFF)

• The default setting is BRIGHT.

then playback will start from the first

chapter or track of the disc. If the playback does not

start automatically, press the PLAY button.

• When you play back the DVD with a title menu, it may

appear on the screen. In this case, refer to “Title menu”

on page 18.

NOTES:

• The brightness of the front panel display can be adjusted

from the setup menu. Details are on page 31.

Press the STOP button to stop playback.

• When you turn on the power next time, the brightness of

the front panel display will be as set in setup menu.

NOTES:

• A “prohibited icon” may appear at the top-right

corner on the TV screen during operation,

TV TYPE

warning that a prohibited operation has been

encountered by the DVD player or the disc.

Select a suitable video system according to the format

of the TV you connected.

• With DVDs that use some titles for playback

program signals, playback may start from the second title,

or it may skip these titles.

Stop playback.

Press the DIMMER NTSC/PAL button on the front

panel more than 3 seconds. The video system will be

displayed on the front panel display and TV screen.

• During the playback of two layered disc, pictures may stop

for a moment. This happens when the 1st layer switches to

the 2nd layer. This is not a malfunction.

• The operation may vary when you play back DVDs with

disc menu or DivX^®video files. Refer to the manual accom-

panying the disc for details.

MULTI

NTSC

PAL

Press the DIMMER NTSC/PAL button on the front

panel more than 3 seconds. The video system will

be displayed on the front panel display and TV

screen.

HDMI Setup

Press the HDMI button on the front panel to select

the HDMI output mode.

The output mode changes as follows every time

the HDMI button is pressed.

MULTI

NTSC

PAL

• The HDMI indicator on the front panel lights up when

HDMI output mode is on.

• If it is left untouched for more than 5 seconds or any

other buttons are pressed, the unit will switch back to

the normal status.

480P/576P

720P

1080

1080P

OFF

NOTES:

480P/576P (Default):

• If the video system setting does not fit to the TV you con-

Video output from the HDMI OUT jack at 480p/576p.

720P: Video output from the HDMI OUT jack at 720p.

1080: Video output from the HDMI OUT jack at 1080i.

1080P: Video output from the HDMI OUT jack at 1080p.

OFF: No video output from the HDMI OUT connector.

nected, the picture will be distorted.

• If you turn off the unit, the video system will go back to the

one set for the TV TYPE on the display menu (refer to

page 28).

NOTES:

General Features

• Video and audio signals may distorted temporarily when

switching to/from the HDMI output mode.

DVD-V DVD-A DivX

•

Use a display equipment with an HDMI-compatible port.

The HDMI indicator on the front panel flashes when you

select the HDMI output mode but there is no HDMI cable.

DVD and DivX^®video file may contain menus to navigate

the disc and access special features. Press the appropri-

ate Numeric buttons or use the Cursor buttons (K / L /

s / B) to highlight your selection in the DVD main menu

and press the ENTER button to confirm.

• If you turn on the pure direct mode, both video and audio

signals thru the HDMI output will be cut off (press the

PURE DIRECT button again to recover).

• You can check the HDMI connection status by pressing the

DISPLAY button during playback with the HDMI output

mode (refer to page 25).

• If the TV is not compatible with newly selected HDMI output

mode, the actual output mode will be kept the one before

changing the selection. When this occurs, the newly select-

ed mode will appear on the front panel display (see page

11) while the actual output resolution will be indicated by

performing the on-screen display as described in NOTE

OFR HDMI DISPLAY on page 25.

NOTES:

• Unless otherwise stated, all operations described in this

manual are based on remote control use. Some operations

can be carried out using the menu bar on the TV screen.

• The Numeric buttons are invalid in menu of DivX^®video

file.

• Actual output signals for each HDMI mode vary with DVD

the compatibility of the connected display device.

• You cannot select the HDMI output mode when the setup

menu is on the TV screen.

–

DISC PLAYBACK

Disc Menu

PAGE SELECTION

Some DVD-Audio discs that include still

images feature a selection of images

you can choose from.

1/12

DVD-V

Press the MENU button.

• The DVD main menu will appear.

If the feature is not available,

appear on the TV screen.

During playback, press the PAGE

+ or – button to select a desired

page number to be displayed.

symbol may

If disc menu is available on the disc, audio language,

subtitle options, chapters for the title and other

options will appear for selection.

Press the Cursor buttons (K / L / s / B) to select an

item, and the ENTER button to confirm the selection.

PLAYBACK OF THE BONUS GROUP

Some discs are recorded with the Bonus Group that can be

played back by entering a password. Refer to the disc jackets.

In stop mode, press the

GROUP button to open the

group search screen.

DVD-AUDIO

BONUS GROUP

Title Menu

Please enter

4-digit password.

Press the Numeric buttons to

select a bonus group number.

• The password popup window appears.

Press the Numeric buttons to enter

the 4-digit password.

DVD-V DVD-A

Press the TOP MENU button.

• The title menu will appear.

• When the correct password is entered, playback starts

If the feature is not available,

appear on the TV screen.

symbol may

from the top of the bonus group.

NOTES:

Press the Cursor buttons (K / L / s / B) to select an

•

In some cases, the password window is displayed on the

item, and the ENTER button to confirm the selection.

menu screen. Follow the instructions given on the screen.

• Playback will begin at the selected title.

• Once the password is entered, playback will be repeated

until the disc is removed from the disc tray.

DivX

Still / Pause

Press the Cursor buttons (K or L) to

choose a track, then press the PLAY or ENTER

button.

Super

DVD-V DVD-A CD

Audio CD

MP3

JPEG WMA DivX

Press the TOP MENU button.

• The title menu will appear.

During playback, press

If the title menu is available on the file, audio lan-

guage, subtitle options, chapter for the title and

other options will appear for selection.

Press the Cursor buttons (K / L / s / B) to select

an item, and the ENTER button to confirm the

selection.

the STILL/PAUSE button.

• Playback will pause and sound will

be muted.

To continue playback, press the PLAY button.

NOTE:

• Set STILL MODE to FIELD on the display menu if pictures in

the pause mode are blurred (refer to page 28).

CALLING UP A MENU SCREEN DURING PLAYBACK

Resume

Super

DVD-V DVD-A DivX

DVD-V DVD-A

Audio CD

MP3

• Press the MENU button to call up the DVD main menu (DVD-V).

• Press the TOP MENU button to call up the title menu.

JPEG WMA DivX

NOTES:

During playback, press the

• Contents of menus and corresponding menu operations

may vary among discs. Refer to the manual accompanying

the disc for details.

Resume ON

STOP button.

• Resume message will appear on

the TV screen.

Press 'PLAY' to play from here.

To play the beginning,

press 'STOP' first and then 'PLAY'.

• During playback or resume stop state on the DivX^®video

file, it is possible to call up a menu.

Press the PLAY button, play-

back will resume from the point at

which playback was stopped.

<Example: DVD>

DVD Audio Playback

• To cancel resume, press the STOP button again.

NOTES:

DVD-A

• For MP3, JPEG or WMA, playback will resume from the

beginning of the current track.

PLAYBACK OF ALL GROUPS

• The resume information will be saved even when the

power is turned off.

In stop mode, press the MODE

ALL GROUP

DVD-AUDIO

TOTAL 2:05:55

button.

• The all group screen appears.

Press the PLAY button to

begin playback.

Fast Forward / Reverse Search

All Group Playback

--no indication--

Super

DVD-V DVD-A

Audio CD

MP3

NOTE:

WMA DivX

During playback, press the h or g button repeat-

• “A-PLAY” is displayed in the front

panel display at step 1

edly to select a desired forward or reverse speed.

• For DVDs, fast forward or reverse search speed is different

depending on the disc. The approximate speed is 1 (x2),

2(x8), 3 (x20), 4 (x50), and 5 (x100).

PLAYBACK FROM A DESIRED GROUP

During playback or in the stop

1/12

mode, press the GROUP button.

Button

Press the Numeric buttons to

select a group.

• The group will be located and play-

back will start.

Button

–

DISC PLAYBACK

• For Audio CDs, Super Audio CDs, MP3, WMA and DivX^®,

the approximate speed is 1 (x2), 2 (x8), and 3 (x30).

To exit zoom mode, press the ZOOM button.

NOTES:

•

For Audio CDs, Super Audio CDs, MP3 and WMA, sound will

•

Zoom function does not work while disc menu is shown.

be output at any speed of fast forward and reverse search.

• x4 zoom is not available on some discs.

• Navigation screen is not available on JPEG.

• You cannot pan through the zoomed picture on some

JPEG files.

To return to normal playback, press the PLAY button.

NOTE:

• For some DivX^®files, Fast Forward/Reverse Search

may not function.

Title / Chapter Search

Slow Forward / Slow Reverse

DVD-V DivX

BY USING THE SEARCH MODE BUTTON

DVD-V DVD-A DivX

only Moving picture

Press the SEARCH MODE button

/29

During playback, press the STILL/PAUSE button.

repeatedly until the chapter

search or the title search display

appears during playback.

Button

Press the h or g button.

• Slow motion playback will begin and

sound will be muted.

Enter the desired chapter/title

number with the Numeric buttons.

Press the h or g button repeat-

edly to select a desired speed.

• Slow forward or reverse speed is dif-

ferent depending on the disc. The

approximate speed is 1 (1/16), 2 (1/8),

and 3 (1/2).

BY USING THE SKIP BUTTONS

During playback, press the

button to move to the next

chapter. Press it repeatedly to skip to subsequent chapters. Press

SKIP

To return to normal playback, press

the

H button to go back to the beginning of the current

SKIP

the PLAY button.

chapter. Press it repeatedly to go to the previous chapters.

• Chapter number will appear briefly on the front panel dis-

play during playback DVD. Track number keeps being dis-

played during playback DivX^®video file.

NOTES:

• On DVDs set STILL MODE to FIELD on the display

menu if pictures in the slow playback mode are blurred

(refer to page 28).

• If the SKIP

button is pressed while the playback

H or

• Only Slow Forward is available when playing back discs

is paused, the playback after skipping to the next chapter

with DivX^®files.

will be also paused.

NOTES:

Step by Step Playback

•

Depending on the disc being played, the Numeric buttons

can be used to search for a desired chapter by entering

the chapter number directly. Refer to the manual accom-

panying the disc.

DVD-V DVD-A DivX

only Moving picture

During playback, press the

• The SKIP H and G buttons are not available when

playback is stopped.

STILL/PAUSE button.

• A disc that does not contain chapters within titles, the

• Playback will pause and sound

will be muted.

SKIP

and

G buttons change the titles.

The disc advances frame by

Track Search

DVD-A CD

frame each time the STILL/PAUSE button is pressed.

To exit step by step playback, press the PLAY button.

Super

Audio CD

MP3 JPEG

WMA DivX

NOTE:

• On DVDs, set STILL MODE to FIELD on the display menu

if pictures in the pause mode are blurred (refer to page 28).

There are two ways to begin playback a disc at a specific track.

Zoom

BY USING THE SEARCH MODE BUTTON

Press the SEARCH MODE button.

• The track search display appears.

Within 30 seconds, select a

desired track number using the Numeric buttons.

• For the disc with less than 10 tracks, press the track

number directly.

• For discs with 10 or more but less than 100 tracks, to

play back a single-digit track, press 0 first, then the

track number (e.g. for track 3, press 0, 3). To play back

a double-digit track, press the track number.

DVD-V DVD-A JPEG DivX

__/ 15

only Moving picture

This function allows you to enlarge the video image and to

pan through the zoomed image.

Press the ZOOM button during playback.

• Playback will continue.

Press the ZOOM button repeatedly to select a

desired zoom factor: x2, x4 or off.

• Only x2 zoom is available on JPEG and DivX^®.

•

For discs with 100 or more tracks, to play back a single- or

a double-digit track, press 0 first, then the track number

(e.g. for track 3, press 0, 0, 3, and for track 26, press 0, 2,

6). To play back a triple-digit track, press the track number.

• Press the CLEAR button to erase the incorrect input.

Use the Cursor buttons (K / L / s / B) to move the

NOTE:

zoomed picture across the screen.

• The +10 button can also bring up the track search dis-

play except for the disc with less than 10 tracks. For

such a disc, track search can be done by just pressing

the track number.

BY USING THE SKIP BUTTONS

During playback, press the

G button to move to the

SKIP

next track. Press it repeatedly to skip to subsequent tracks.

Press the

H button to go back to the beginning of the

SKIP

current track. Press it repeatedly to go to the previous tracks.

•

Track number will appear briefly on the front panel display.

• If the SKIP H or G button is pressed while the playback

is paused, the playback will be paused again after skipping

to the next track.

–

DISC PLAYBACK

NOTES:

• The SKIP H and G buttons are not available when

playback is stopped.

• The Repeat Title/Chapter setting will be cleared when

moving to other title or chapter.

• Repeat playback does not function during A-B repeat

playback.

• When the SKIP H, G button is pressed during play-

back DivX^®video file, and if it does not change previ-

ous/next track, press the MENU button.

• Repeat Title/Chapter is not available with some scenes.

Time Search

REPEAT TRACK / GROUP / ALL

Super

DVD-V DVD-A CD

Audio CD

DivX

Super

Audio CD

Press the SEARCH MODE button until the time

search screen appears on the TV screen.

Within 30 seconds, enter a

To activate Repeat function, press the REPEAT button during

playback.

•

The repeat mode changes as described below every time

you press the button.

desired disc time point on the

: :

- -- --

1:23:45

disc with the Numeric buttons.

• Playback will start at the speci-

fied time.

OFF

TRACK

(current track repeat)

ALL

(repeat off)

(entire disc repeat)

• For Time Search, “0” appears automatically when there

is no need to enter a number. For example,

“0:0_:_ _” appears in the time search screen if the total

time of the disc is less than 10 minutes.

NOTES:

• In the track repeat, the repeat setting will be cleared

when moving to other track.

• Repeat playback does not function during A-B repeat

playback.

Press the CLEAR button to erase an incorrect input.

NOTE:

• For some DivX^®files, Time Search may not function.

DVD-A MP3 JPEG WMA DivX

Marker Setup Screen

DVD-V DVD-A

TRACK

(current track

repeat)

GROUP

ALL

OFF

(repeat off)

Super

Audio CD

(current folder

repeat)

(entire disc

repeat)

You can use markers to memorize your favorite places on a disc.

Press the SEARCH MODE

button repeatedly until the dis-

play screen and Markers

appear during playback.

Press the Cursor buttons (s or B) to select the

number of the marker (1-10) and ensure that “_ : _

_ : _ _” appears in the display.

When the disc reaches the point you want to

remember, press the ENTER button.

• The title or track and elapsed playback time will appear

in the TV screen.

1 2 3 4 5 6 7 8 9

-- -- -- --

NOTES:

• In the track or group repeat, the repeat setting will be

cleared when moving to other track or group.

• When the DivX^®media file change to DivX^®video file

while the repeat setting is done, the repeat setting will

be cleared.

• For DVD-Audio, ALL repeat is effective only when all

groups are being played back.

A-B REPEAT

Super

To return to the Marker later, press the SEARCH

MODE button repeatedly during playback and the

Cursor buttons (s or B) button to choose a

desired marker, then press the ENTER button.

DVD-V DVD-A CD

Audio CD

DivX

Press the A-B REPEAT button

A -

at your chosen starting point.

•

A- appears briefly on the TV

Press the SEARCH MODE or RETURN button to exit.

screen.

Press the A-B REPEAT button

again at your chosen end point.

A - B

NOTES:

• Opening the disc tray, turning off the power or selecting

AC at step

•

A-B appears briefly on the

and pressing the ENTER button will

erase all Markers.

TV screen, and the repeat sequence begins.

• To clear a marker, using the Cursor buttons (s or B),

position the cursor on to the marker number to be

cleared and press the CLEAR button.

• You can mark up to 10 points.

To exit the sequence, press

OFF

the A-B REPEAT button.

NOTES:

• The A-B Repeat section can only be set within the cur-

rent title (for DVDs or DivX^®Video files), or current track

(for DVD-Audio, Audio CD, Super Audio CD and disc

with DivX^®media files.).

Repeat

• The REPEAT button is available only during playback.

• A-B Repeat is not available with some scenes on DVD.

• To cancel the A point which was set, press the CLEAR

button.

• A-B Repeat playback does not function during title,

chapter, track, group or all repeat playback.

• For some DivX^®files, A-B Repeat playback may not

function.

REPEAT TITLE / CHAPTER

DVD-V DivX

To activate Repeat function, press the REPEAT button during

playback.

•

The repeat mode changes as described below every time

you press the button.

OFF

(repeat off)

CHAPTER

(current chapter repeat) (current title repeat)

TITLE

–

DISC PLAYBACK

Program Playback

This function allows you to program a playback order of

DVD-Audio, Audio CD, Super Audio CD, MP3, JPEG, or

WMA in a desired sequence.

NOTES:

•

Press the STOP button once and then the PLAY button

again, playback will restart from the point where the STOP

button was pressed. (Program continued.)

•

Press the STOP button twice and then the PLAY button

again, playback will restart from the first track in the usual

way. Your program is still stored until either the disc tray is

open or power is turned off.

DVD-A

In stop mode, press the MODE

button repeatedly until the pro-

gram screen appears.

• The group selection screen will

appear.

PROGRAM

DVD-AUDIO

TOTAL 0:00:00

1:02:25

1:03:30

• Up to 99 tracks can be entered.

ALL CLEAR

•

To erase tracks in the program all together, select ALL

CLEAR at the bottom of the list at step

1/1

. And, “A-CLEAr”

1:02:25

is displayed on the front panel display at that time.

To repeat the current track in the program, press the

Press the Cursor buttons

•

(▲ or ▼) to select a group, then press the ENTER

button.

REPEAT button repeatedly until

TRACK appears during

playback. To repeat the entire program press the REPEAT

• The track selection screen will be displayed.

• It takes approximately five seconds until the track

selection screen appears.

button repeatedly until

ALL appears during playback.

• If eight or more tracks were set in a program, use the

H or G button to see all the tracks.

SKIP

Press the Cursor buttons (▲ or ▼) to select a

track, then press the ENTER button.

• When selecting the folder:

–Press the Cursor button (B) when you want to go to

the next hierarchy.

•

Press the CLEAR button to erase the most recently

–

Press the Cursor button ({) when you want to go back

entered track.

to the previous hierarchy (except for the top hierarchy).

• Press the Cursor button (s) button to go back to the

group selection screen from the track selection screen.

Press the PLAY button to play back the pro-

grammed tracks.

• Even if an inserted disc contains mixed MP3, JPEG

and WMA files, Program function allows 99 tracks in

combination of MP3, JPEG and WMA files.

• The front panel display has blinked while setting the

program playback.

Super

In stop mode, press the MODE button.

• The program screen will appear.

Press the Cursor buttons

(▲ or ▼) to select a track, then

press the ENTER button.

Audio CD

•

“F-*** ” is displayed in the front panel display while select-

ing the group (folder). ( *** is group (folder) number.)

PROGRAM

CD-DA

TOTAL 0:03:30

Random Playback

This function shuffles the playback order of tracks instead of

playback in the original sequence.

3:30

4:30

5:00

3:10

5:10

1:30

2:30

1/1

1/2

DVD-A

3:30

•

Press the CLEAR button to erase

In stop mode, press the

RANDOM button.

the most recently entered track.

Press the PLAY button to start

programmed playback.

RANDOM

DVD-AUDIO

<Example: CD>

• The random screen will appear.

Press the Cursor buttons (▲ or

▼) to select a desired group to

play back randomly, then press

the ENTER or PLAY button.

• Random playback will start.

ALL

0:44:44

0:03:26

1/1

ALL

MP3 JPEG WMA

In stop mode, press the MODE

button.

• The program screen will appear.

Press the Cursor buttons (K or

L) to select a group, then press

the ENTER button.

• A track selection screen appears.

Press the Cursor buttons (K or

L) to select a track, then press

the ENTER button to save it in a

program.

PROGRAM

MY COLLECTION

ABC

Super

DEF

GHI

Audio CD

MP3 JPEG WMA

ALL CLEAR

1/1

In stop mode, press the

ABC

RANDOM

CD-DA

TOTAL 0:45:55

RANDOM button.

• The random screen will appear

Press the PLAY button to start

random playback.

RANDOM PROGRAM

--no indication--

PROGRAM

ABC

DEF

GHI

JKL

MNO

<Example: CD>

ALL CLEAR

1/1

2/2

NOTES:

DEF

• Press the CLEAR button to erase

the most recently entered track.

• The programmed track is dis-

played in the right-hand screen.

• To repeat the current track in the random selection,

press the REPEAT button repeatedly until

appears during playback. To repeat the entire random

selection press the REPEAT button repeatedly until

ALL appears during playback.

TRACK

PROGRAM

ABC

•

If the entire program cannot be dis-

played on the screen, “L” appears.

DEF

GHI

JKL

DEF

• You cannot go back to the previous track during ran-

dom playback.

• For a disc containing mixed MP3, JPEG and WMA

files, random playback of those files will be performed.

• “SHUFFLE” is displayed on the front panel display at

step 1

• Pressing the Cursor button (s)

will show a list of folders that

belong to the hierarchy which is

one-level higher than the currently

selected folder.

MNO

ALL CLEAR

1/1

2/2

DEF

Press the PLAY button to start programmed playback.

• Press the RETURN button, and the stop screen will

show up with the program contents in memory.

–

DISC PLAYBACK

Information on MP3, JPEG and WMA discs

This DVD player can play back images and sounds from data record-

ed in MP3 and JPEG formats on DVD-R/RW or CD-R/RW discs.

A file with an extension of “.mp3 (MP3)” is called an MP3 file.

• A file with an extension of “.jpg (JPG)” or “.jpeg (JPEG)” is

called a JPEG file.

MP3 / JPEG / WMA Playback

•

MP3 JPEG WMA

When a DVD-R/RW or CD-R/RW disc with MP3, JPEG or

WMA files is inserted in the DVD player, the file list will

appear on display. The number of tracks is also displayed on

the front panel.

The DVD player can run an image file conforming to the

Exif specification. Exif is a file format, Exchangeable

Image File format established by Japanese Electronic

Industry Development Association (JEIDA).

Press the Cursor buttons (K or L) to select the

desired group (folder) or track.

• To return to the previous screen, press the Cursor button (s).

• If a group (folder) is selected, press the Cursor button

(B) or ENTER button to go on to the track selection

screen. Press the Cursor buttons (K or L) to choose a

track, then press the PLAY or ENTER button.

• If a track is selected, press the PLAY or ENTER button

to start playing back tracks. The selected track and the

subsequent tracks will be played back.

•

A file with an extension of “.wma (WMA)” is called a WMA file.

• Files whose extension is other than “.mp3 (MP3)”, “.jpg

(JPG)” and “.jpeg (JPEG)” or “.wma (WMA)” will not be

listed on the MP3, JPEG or WMA menu.

• If the file is not recorded in MP3, JPEG or WMA format,

noise may be produced even if the file extension is either

“.mp3 (MP3)”, “.jpg (JPG)”, “.jpeg (JPEG)” or “.wma (WMA)”.

The name of group and track can be displayed up to 25 char-

acters. Unrecognizable characters will be replaced with aster-

isks. The ninth and deeper hierarchies cannot be displayed.

• Unplayable groups or tracks may be displayed depending

on the recording conditions.

• If the TOP MENU button is pressed when a file list is dis-

played, the first item will be highlighted.

•

• When selecting the folders

–Press the Cursor button (B) when you want to go to

the next hierarchy.

–Press the Cursor button ({) when you want to go back

to the previous hierarchy (except for the top hierarchy).

• Press the TOP MENU button to return to the first item.

Press the STOP button to stop playback.

NOTES:

Kodak Picture CD

• Folders are known as Groups; files are known as Tracks.

The DVD player can also run JPEG files stored on Kodak

Picture CDs. You can enjoy picture images on the television

set by playing back the Picture CDs.

• A symbol of

is shown on the top of the group name.

is shown on the top of MP3 files.

is shown on the top of JPEG files.

is shown on the top of WMA files.

• A symbol of

This unit confirms to ver. 7.0 of Kodak Picture CD.

For details of Kodak Picture CD, contact a shop that provide

developing service of Kodak Inc.

• Maximum of 255 folders can be recognized.

• Maximum of 999 files can be recognized.

• Up to 8 hierarchies can be recognized.

When Kodak Picture CD is inserted in the DVD

player, Kodak Picture CD menu appear automati-

cally on the TV screen.

• If the track extends beyond the scope of screen, a

down arrow “L” appears, indicating that the user can

view another part on the previous page. The current

page number and the number of total pages are shown

on the left of the down arrow “L”.

• If all menu items cannot be

displayed on the screen

Picture1

Picture2

Picture3

• If no MP3, JPEG or WMA files are found in the group,

the group is not displayed.

scope, “G” appears at the

right bottom of the screen,

indicating that the user can

view remaining items on the

next page. “H” appears, it

indicates that the user can

view other items on the pre-

vious page. The track num-

ber of the currently highlighted item and the total tracks

are shown at the center bottom of the screen.

• If “G” is shown at the right bottom, use the SKIP

button to view the next page. If “H” is shown at the

left bottom, use the SKIP H button to view the previ-

ous page.

• It may take some time until all menu items are dis-

played on the menu screen.

• The DVD player can reproduce data recorded as per

ISO 9660 Level 1, Level 2 or Joliet on the disc.

• It can also run a disc on which data is recorded in a

multi-session.

Picture4

Picture5

1/32

Picture6

•

For more details of recording systems, refer to the instruction man-

ual for the DVD-R/RW / CD-R/RW drive or the writing software.

Current track number /

the number of total tracks

• For MP3 and WMA files recorded in Variable Bit Rate

(VBR), the unit may not display the actual elapsed time.

This player recommends the use of files recorded at the fol-

lowing specifications:

Applicable MP3 file

Remarks

• It is prohibited to record

MP3 sound on a digital

device when the connection

is made digitally.

Sampling

frequency

44.1kHz

48kHz

Press the Cursor buttons (K / L / s / B), select a

• MP3 files recorded at fixed

bit rate of 32 kbps or higher

are recommended.

MPEG1

audio layer 3

desired track to be played back, then press the

Type

PLAY or ENTER button.

• If a Kodak Picture CD file is selected, an image will be

played back from the selected track and go to the next

one in turn.

Applicable JPEG file

Upper limit:

Size of

image

Remarks

• A JPEG image that extends

beyond the screen is

reduced so that it will be

displayed within the screen.

6300x5100 dots

Lower limit:

32x32 dots

Press the STOP button to stop playback.

NOTES on JPEG and Kodak Picture CD:

• A track is displayed for 5 or 10 seconds and then the

next track is displayed.

Applicable WMA file

Sampling

frequency

Remarks

44.1kHz

48kHz

• Those frequencies are

applicable to WMA version 9.

• Every press on the ANGLE button will turn the image

clockwise by 90 degrees when an image is displayed.

• To change the size of the playback image, press the

MODE button twice. The size change mode appears on

top of the TV screen during playback. Then press the

Cursor buttons (s or B) or ENTER button to switch

between NORMAL (100%) and SMALL (95%).

• Progressive JPEGs (JPEG files saved in the progres-

sive format) will not be played back on this DVD player.

• High resolution JPEG files take longer to be displayed.

• Ensure that the copyright

function is set to off when

preparing a WMA disc.

Bit rate

48–192kbps

• A prohibition “disable” sym-

bol will appear if the user

attempts to run a non-repro-

Type

WMA version 9 ducible file such as copy-

right-protected.

• Recorded in Multi-channel for-

mat cannot be played back.

–

DISC PLAYBACK

• The size change mode may have no effect on some

files (e.g. files with a small picture size).

• In stop mode, press the MENU button. Kodak Picture

CD menu appears.

• Although DivX^®logo has been obtained for this player, it

may not be able to play back some data, depending on

the disc characteristics, bit rates, or audio format set-

tings, etc.

• Use the software recognized by DivX^®, Inc. when you

make DivX^®files.

NOTES on WMA:

• When using tools or utilities to make up DivX^®files, read

their instruction manual beforehand.

• The DVD player can reproduce data recorded as ISO

9660 level 2 with 31 characters file name included

punctuation marks. The name of file can be displayed

up to 25 characters.

• A DivX^®file whose file size exceeds 2GB cannot be

played back.

• If a large-sized DivX^®file is selected, it may take a while

to start the playback (over 20 seconds sometimes).

• Constant bit rate of image between 500 kbps and 4,000

kbps is recommended if you make DivX^®files on a CD-

R/RW.

• Maximum of 8 subfolders can be recognized.

• It can also be displayed tag information of WMA at

least 64 characters.

• A file with an extension of Joliet as Unicode format in

up to 64 characters can be recognized.

• This unit cannot play back copyright protected WMA

files.

• If DivX^®files written on CD discs cannot be played back,

rewrite them on a DVD disc and try to play back.

• For more information for DivX^®, please visit:

http://www.divx.com

• If you insert a DVD-R/RW or CD-R/RW with DivX^®files

that are mixed with MP3, JPEG, or WMA files, the

Playback Media Selection screen will be displayed.

DivX Playback

DivX

This DVD player can play back DVD-R/RW and CD-R/RW

discs recorded in DivX^®format. When a DVD-R/RW or CD-

R/RW with DivX^®files is inserted in the DVD player, the file

Please select Video and proceed to step

list will appear automatically on the TV screen. The number

of tracks will be also displayed on the front panel.

Please select the media to play back.

Video

Audio

Pictures

Press the Cursor buttons (K or L) to select the

desired group (folder) or track.

• To return to the previous screen, press the Cursor button (s).

• If a group (folder) is selected, press the Cursor button

(B) or ENTER button to go on to the track selection

screen. Press the Cursor buttons (K or L) to choose a

track, then press the PLAY or ENTER button.

• If a track is selected, press the PLAY or ENTER button

to start playing back tracks. The selected track and the

subsequent tracks will be played back.

• Press the TOP MENU button to call up the Playback

Media Selection screen in stop mode.

• If you select Audio & Pictures, instead of Video on the

Playback Media Selection screen, the DVD player can

play back MP3/JPEG/WMA files. Refer to page 22 for

details.

This player recommends the use of files recorded at the

following specifi cations:

• When selecting the folders

–Press the Cursor button (B) when you want to go to

the next hierarchy.

–Press the Cursor button ({) when you want to go back

to the previous hierarchy (except for the top hierarchy).

• Press the TOP MENU button to return to the first item.

Applicable DivX^®ﬁle

Remarks

Plays all versions of

Playable

Codec of

AVI ﬁles

DivX^®video (including • They are recognized

DivX^®6) with standard

as MPEG 4.

playback of DivX^®

media ﬁles.

Press the STOP button to stop playback.

NOTES:

• DivX^®is a codec (compression / decompression) that

Maximum

size of image

720 x 480 @30fps

720 x 576 @25fps

can compress images to a very small amount of data.

The software can compress video data from almost any

sources to the size that can be sent on the Internet

without compromising visual quality of the images.

• A file with an extension of “.avi” or “.divx” is called a

DivX^®file. All files with the “.avi” extension are recog-

nized as MPEG 4.

• It is prohibited to

record MP3 sound

on a digital device

when the connection

is made digitally.

Sampling

frequency

of audio

8kHz - 48kHz

• Files with extension other than “.avi” and “.divx” will not

be listed on the DivX^®menu. However, unplayable

groups or tracks may be displayed, depending on the

recording conditions.

• MP3 ﬁles recorded

at ﬁxed bit rate of

32kbps or higher

are recommended.

MPEG1 audio layer 3

(MP3) MPEG1 audio

layer 2 Dolby Digital

Audio type

• Even if the file has an extension of either “.avi” or

“.divx”, this player cannot play it back if it is recorded in

the format other than DivX^®.

• Folders are known as Groups; files are known as tracks.

• A symbol of

is shown on the top of DivX^®file.

• Maximum of 255 folders can be recognized.

• Maximum of 999 files can be recognized.

• If the track extends beyond the scope of screen, a

down arrow “L” appears, indicating that the user can

view another part on the previous page. The current

page number and the number of total pages are shown

on the left of the down arrow “L”.

• The name of group and track can be displayed up to 25

characters. Unrecognizable characters will be replaced

with asterisks. The ninth and deeper hierarchies cannot

be displayed.

• You can play back the disc recorded in multi-session.

• Playback will be paused if the file list is displayed during

the playback.

• It may take a while for audio and images to be output

after you inserted a disc and pressed the PLAY button.

• When playing back the files recorded in high bit rates,

the images can be interrupted on some occasions.

–

DISC PLAYBACK

DivX Subtitle

DVD-A

Press the DISPLAY button during playback.

DivX

• Current track number/total tracks, elapsed time and

remaining time of the current track, and current play-

back status will be displayed.

The subtitle created by the user can be displayed during

DivX^®media file playback.

After select the DivX^®media file, the SUBTITLE LIST

will appear except when the “DivX SUBTITLE” setting

is “OFF”. Refer to “Language Setting” on page 28.

Press the DISPLAY button again.

• Current group number/total groups, elapsed time and

remaining time of the current group, and current play-

back status will be displayed.

Press the DISPLAY button again.

SUBTITLE LIST

•

The bit rate and current playback

status will be displayed.

IIIIIII

FILE

ﬁ le name1

[OFF]

[ASS]

[SMI]

[SRT]

[SSA]

[SUB]

[TXT]

• Current repeat setting appears

on the right side of the display bar only when the

repeat setting is active.

FILE LIST MENU

(

T: Track repeat/ G: Group repeat/A B: A-B repeat)

• If you are playing back a two-layered disc, the layer

number will also be displayed.

Press the Cursor buttons (K or L) to select the

desired extension you want to display, then press

the ENTER button. DivX^®media file with the subti-

tle starts playback. The subtitle cannot be dis-

(L0: Layer 0 is being played back. L1: Layer 1 is being played back.)

Press the DISPLAY button again.

•

During all group, program or random playback, each

playback status will be displayed when you press the

DISPLAY button. Then press the DISPLAY button again.

Current HDMI status will be displayed during the HDMI output

mode. (Refer to NOTE FOR HDMI DISPLAY on page 25.)

played when the setting is “OFF”.

• If there is more than one extension, the extension selec-

tion appears in the SUBTITLE LIST.

•

NOTES:

• DivX^®subtitle can only be displayed according to the

Press the DISPLAY button again to exit.

same name with an extension of the DivX^®file name.

• Files whose extension is other than “.ASS”, “.ass”, “.SMI”,

“.smi”, “.SRT”, “.srt”, “.SSA”, “.ssa”, “.SUB”, “.sub”, “.TXT”

and “.txt” will not be listed in the SUBTITLE LIST.

• This unit cannot be recognized if the DivX^®media file

and its subtitle file are not in the one folder.

Super

Audio CD

Press the DISPLAY button during playback.

• Current track number/total tracks, elapsed time and

remaining time of the current track, and current play-

back status will be displayed.

• The subtitle may not be displayed if the file size is too large.

• To change the subtitle, refer to “Subtitle Language” on

page 26 if multiple subtitles are available.

• The subtitle cannot display if the on-screen information

is displayed.

• If “DivX SUBTITLE” is set to “OFF” in LANGUAGE

menu, the SUBTITLE LIST will not be displayed even if

you select a DivX^®media file with created subtitle.

• Unrecognizable characters will be replaced with asterisks.

• DivX^®subtitle function is invalid to DivX^®video file.

• Some files whose extension is “.SUB”, “.sub”, “.TXT”

and “.txt” may not be displayed.

• Current repeat setting appears on the right side of the

display bar only when the Repeat setting is active.

(

T:Track repeat/ A: All tracks repeat/A B: A-B repeat)

Press the DISPLAY button again.

• Current track number/total tracks, elapsed time and

remaining time of the entire disc, and current playback

status will be displayed.

• Current repeat setting appears on the right side of the

display bar only when the Repeat setting is active.

(

T:Track repeat/ A: All tracks repeat/A B: A-B repeat)

• When you are playing back a disc in program or random

mode, PROGRAM (or RANDOM) will be displayed.

Changing the On-Screen Display

Press the DISPLAY button again.

You can check information about the current disc by pressing

the DISPLAY button on the remote control.

• During program or random playback, each playback

status will be displayed when you press the DISPLAY

button. Then press the DISPLAY button again.

DVD-V

•

Current HDMI status will be displayed during the HDMI out-

put mode. (Refer to NOTE FOR HDMI DISPLAY on page 25.)

Press the DISPLAY button

9/49

0:00:00 -0:03:30

during playback.

Press the DISPLAY button again to exit.

•

Current chapter number/total

chapters, elapsed time and

MP3 JPEG

remaining time of the current chapter, and current play-

back status will be displayed.

Press the DISPLAY button

TRACK 01

during playback.

Press the DISPLAY button again.

• Current file name will be dis-

played.

• Current title number/total titles, elapsed time and

remaining time of the current title, and current playback

status will be displayed.

<Example: MP3>

Press the DISPLAY button again.

• Current track number/total

tracks and elapsed time (MP3)

will be displayed.

TR 1/36 0:01:15

Press the DISPLAY button

IIIIIII

again.

•

The bit rate (the amount of

video data currently being read)

and current playback status will be displayed.

• Current repeat setting appears only when the Repeat

setting is active.

(

T:Track repeat/ A: All (disc) repeat/ G: Group repeat).

• Current repeat setting appears on the right side of the

display bar only when the repeat setting is active.

• When you are playing back a disc with MP3 or JPEG

files in program or random mode,

RANDOM) will be displayed.

PROGRAM (or

(

C: Chapter repeat/ T: Title repeat/A B: A-B repeat)

• If you are playing back a two-layered disc, the layer

number will also be displayed.

Press the DISPLAY button again.

(L0: Layer 0 is played back. L1: Layer 1 is played back.)

• During program or random playback, each playback

status will be displayed when you press the DISPLAY

button. Then press the DISPLAY button again.

Press the DISPLAY button again.

• Current HDMI status will be displayed during the HDMI

output mode. (Refer to NOTE FOR HDMI DISPLAY on

page 25.)

•

Current HDMI status will be displayed during the HDMI out-

put mode. (Refer to NOTE FOR HDMI DISPLAY on page 25.)

–

Press the DISPLAY button again to exit.

–

DISC PLAYBACK

Press the DISPLAY button again to exit.

WMA

NOTE FOR HDMI DISPLAY:

Press the DISPLAY button

TRACK 01

• The displayed HDMI status

are as follows:

during playback.

VIDEO INFO.

AUDIO INFO.

MAX CHANNEL

YCbCr/1080i

BITSTREAM

2ch

• Current file name will be dis-

played.

1. Information for image out-

put/Resolution of image

Press the DISPLAY button

2. Sound output format

TITLE NAME

again.

3. Maximum number of audio channels that can be

• Title name based on tag infor-

mation of currently played-back

file will be displayed.

accepted by the connected equipment

Slide Show Mode

Press the DISPLAY button

ARTIST NAME

again.

JPEG

• Artist name based on tag infor-

mation of currently played-back

file will be displayed.

You can switch to the slide show mode during playback.

Press the MODE button during playback.

• The slide show mode screen will appear.

Press the DISPLAY button

TR 1/36 0:01:15

again.

• You cannot change to the slide show mode in stop mode

or from the file list screen or the Picture CD menu screen.

• Current track number/total

tracks and elapsed time will be

displayed.

Press the ENTER button.

• The slide show mode will change.

CUT IN/OUT: The entire image appears in one time.

FADE IN/OUT: The image appears and disappears

gradually.

• Current repeat setting appears only when the Repeat

setting is active.

(

T: Track repeat/ A: All (disc) repeat/ G: Group

(folder) repeat).

• When you are playing back a disc in program or ran-

dom mode,

played.

Press the MODE button to exit.

PROGRAM (or RANDOM) will be dis-

Dialog Speed

Press the DISPLAY button again.

• During program or random playback, each playback

status will be displayed when you press the DISPLAY

button. Then press the DISPLAY button again.

• Current HDMI status will be displayed during the HDMI

output mode. (Refer to NOTE FOR HDMI DISPLAY on

this page.)

DVD-V DVD-A

only Moving picture

Available only on discs recorded in the Dolby Digital format,

Dialog Speed plays back in slightly faster or slower speed

while keeping the sound quality as in the normal playback.

During playback, press the

MODE button repeatedly until

the Dialog Speed setting

appears.

Press the DISPLAY button again to exit.

OFF

NOTE:

• If the file does not contain tag information, NOT AVAIL-

ABLE will be displayed.

• OFF appears on the TV screen.

DivX

Press the ENTER button or the Cursor buttons (s or

B) to switch among (x1.3), (x0.8) and OFF.

Press the DISPLAY button.

File Name

• Current file name will be dis-

played.

: Plays back approximately at 0.8 times of nor-

Press the DISPLAY button.

mal playback.

: Plays back approximately at 1.3 times of nor-

mal playback.

To return to normal playback, press the PLAY button.

• Current track number/total

tracks and elapsed time will be

displayed.

10/15 0:01:15 -0:05:56

• During playback DivX^®video

NOTES:

file, “--:--:--” is displayed at elapsed/remain time.

• Every time you press the STOP button, the setting will

• Current repeat setting appears only when the Repeat

be turned OFF.

setting is active.

• Subtitle can be viewed during this function.

• Picture Control, Black Level, Audio Language and

Virtual Surround setting cannot be changed while using

this mode.

• Virtual Surround does not function while using this mode.

• This feature may not work at some point on a disc.

• When using digital audio connection (COAXIAL, OPTI-

CAL or HDMI), the LPCM sound will be output.

• When using the Dialog Speed function with Multi-chan-

nel digital outputting, the analog output sound will be

fixed at 2 channel.

DivX^®media file: ( T: Track repeat / A: All(disc)

repeat/ G: Group repeat /

(

B: A-B repeat)

T: Title repeat / C: Chapter

DivX^®video file:

repeat / A B: A-B repeat)

Press the DISPLAY button.

10/15 0:01:15 -0:05:56

• Current chapter number/total

Chapters, elapsed time and

remaining time of the current

chapter, and current playback status will be displayed.

• During playback DivX^®video file only, this On-screen is

displayed.

• When using digital audio connection, only the Dolby

Digital sound will be available.

• This feature does not work when the video format of

the inserted disc does not match to the output video

format setting of this unit (playing NTSC disc while TV

TYPE is set to PAL etc.).

Press the DISPLAY button.

• Current title number/total titles, elapsed time and

remaining time of the current title, and current playback

status will be displayed.

• During playback DivX^®video file only, this On-screen is

displayed.

Press the DISPLAY button again.

• Current HDMI status will be displayed during the HDMI

output mode. (Refer to NOTE FOR HDMI DISPLAY on

this page)

–

DISC PLAYBACK

Audio Language

<DVD>

1.ENG/6

<DivX^®>

1 / 8

ENG

Letterbox

DVD-V DivX

The DVD player allows you to select a language (if multiple

2.FRE/6

2 / 8

Wide screen

ITA

languages are available) during DVD or DivX^®disc playback.

Press the AUDIO button during playback.

Press the AUDIO button repeatedly to select your

desired language.

OFF

<DVD>

<DivX^®>

1.ENG Dolby D 3/2.1ch 48k/3

1. Dolby D / 8 ENG

Director Commentary

• For DivX^®several subtitle tag information exists. Some

examples are shown as follows.

2.FRE Dolby D 3/2.1ch 48k/3

2. Dolby D / 8 FRE

Writer Commentary

Letterbox:

Subtitle for the letterbox version of the

movie.

Wide screen: Subtitle for the widescreen version of the

movie.

Children:

etc.

Subtitle for an audience of children.

3.JPN Dolby D 3/2.1ch 48k/3

8. MP3 / 8 SPA

Cast Commentary

To turn off subtitles, press the SUBTITLE button

repeatedly until OFF appears.

• For DivX^®several audio tag information exists. Some

examples are shown as follows.

NOTES:

• Some discs allow subtitle language setting on the disc

menu. (Operation varies between discs. Refer to the

manual accompanying the disc.)

Pressing the SUBTITLE button may not work on some

DVDs with multiple subtitle languages (e.g. DVDs which

allow subtitle language setting on the disc menu).

Director Commentary: Audio recorded comment of the

movie director.

•

Writer Commentary: Audio recorded comment of the

movie writer.

Cast Commentary:

Audio recorded comment of the

movie actors.

• If your desired language is not shown after pressing the

SUBTITLE button several times, the disc does not have

subtitles in that language.

etc.

• If you choose a language that has a three-letter lan-

guage code, the code will be displayed every time you

change the Subtitle Language setting. If you choose

any other Languages, ‘---’ will be displayed instead

(refer to page 32).

NOTES:

• The sound mode cannot be changed during playback

of discs not recorded in double sound.

• Some discs allow to change audio language setting on

the disc menu. (Operation varies between discs. Refer

to the manual accompanying the disc.)

• Pressing the AUDIO button may not work on some DVDs

with multiple audio languages (e.g. DVDs which allow to

change audio language setting on the disc menu).

• If the disc has no subtitle language, NOT AVAILABLE

will be displayed.

• For discs with DivX^®files, the screen only displays the

number of subtitle languages.

• If the DivX^®file has no subtitle tag information, the sub-

title tag is not displayed.

•

If you choose a language that has a three-letter language

code, the code will be displayed every time you change the

Audio Language setting. If you choose any other

Camera Angle

DVD-V

Some DVD discs contain scenes which have been shot

simultaneously from various angles. You can change the

Languages, ‘---’ will be displayed instead (refer to page 32).

• Audio Language selection cannot be made during

Dialog Speed in DVD (refer to page 25).

• If the disc has no audio language, NOT AVAILABLE will

be displayed.

camera angle when the (

) mark appears on the screen.

• If the DivX^®file has no audio tag information, the audio

tag is not displayed.

Press the ANGLE button during playback.

• The selected angle will be displayed on the display bar

at the top of the screen.

Press the ANGLE button repeatedly to select your

desired angle.

Subtitle Language

DVD-V DivX

The DVD player allows you to select a subtitle language (if

multiple languages are available) during DVD or DivX^®disc

playback.

1 / 8

Angle 1

Press the SUBTITLE button during playback.

Press the SUBTITLE button repeatedly to select

your desired subtitle language.

2 / 8

Angle 2

• The selected language will be displayed on the display

bar at the top of the screen.

• Press the Cursor buttons (s or B) to turn on or off

subtitles during playback.

8 / 8

Angle 8

NOTE:

• If the ANGLE ICON setting is OFF in the others menu,

the ( ) will not appear (refer to page 31).

–

DISC PLAYBACK

Picture Control

Super Audio CD Setup

Super

Audio CD

DVD-V DVD-A DivX

Picture Control adjusts Brightness, Contrast, Color, Gamma

Correction and Sharpness of the specific display.

Press the SUPER AUDIO CD SET UP button

repeatedly to select among MULTI-CH AREA, CD

AREA, or 2CH AREA.

During playback, press the

MODE button.

Press the Cursor buttons (K

or L) to switch among items.

BRIGHTNESS

+1B

MULTI-CH AREA - Playback in multi channel format.The

number of channels depends on the disc

being played.

CD AREA

- Playback in the same quality with sound

as normal CDs.

Press the ENTER button or the Cursor buttons (

) to adjust the selected item to a desired level.

2CH AREA

- Playback in higher quality than that of

normal CD sound.

•

-6, -5, -4, -3, -2, -1, 0, +1, +2, +3, +4, +5, +6 can be selected.

To return to normal playback, press the RETURN

button.

MULTI-CH AREA

SACD

NOTES:

•

The default settings for all items in Picture Control are “0”.

The setting display will disappear in 10 seconds of no use.

• This function cannot be used during Dialog Speed

(refer to page 25).

CD AREA

• If you return all items to the default settings, select “INI-

TIALIZE” at step

2CH AREA

SACD

Sound Mode

DVD-A

front panel display

This function allows you to select a desired sound mode dur-

ing DVD-Audio playback.

NOTES:

•

The Virtual Surround setting is not available for Super

Audio CDs. (It may be possible to use the Virtual Surround

setting when playing back discs that include a CD area.)

• Some playback options may not be available.These will

be skipped.

• MULTI-CH AREA is selected as default.

Press the AUDIO button during playback.

Press the AUDIO button repeatedly to select your

desired sound.

1.LPCM 3/2.1ch 96k/2

NOTE:

• When selecting a multi-

Virtual Surround

channel sound, it may

not mixed down in

some cases even

DVD-V DVD-A CD

MP3 WMA

2.PPCM 2/0ch 96k/2

You can enjoy stereo phonic virtual space through your exist-

ing 2 channel stereo system.

though the HDMI

AUDIO or ANALOG

AUDIO is 2 CHANNEL.

During playback, press the MODE

button repeatedly until the Virtual

Surround setting appears.

OFF

Stereo Sound Mode

Press the ENTER button to set

it 1(Natural effect), 2(Emphasized effect) or OFF.

Press the RETURN button to exit.

Press the AUDIO button repeatedly during play-

back to select your desired sound mode.

STEREO - both right and left channels are active (stereo)

NOTES:

• Select Virtual Surround OFF or lower the volume if the

sound is distorted.

• Virtual Surround will not be effective if the sound mode

is set to something other than STEREO (for Audio CD

playback only).

• This function cannot be used during Dialog Speed

(refer to page 25).

• Set HDMI AUDIO and ANALOG AUDIO to 2 CHANNEL

to use this function (refer to pages 29-30).

L-ch

R-ch

- only left channel is active

- only right channel is active

STEREO

Both right and left channels

are active (stereo).

•

The Virtual Surround setting is not available for Super

Audio CDs. (It may be possible to use the Virtual Surround

setting when playing back discs that include a CD area.)

L-ch

R-ch

Only the left channel

is active.

Black Level Setting

Only the right channel

is active.

DVD-V DVD-A DivX

Adjust the Black Level Setting to make the black parts of the

picture as bright as you prefer.

NOTE:

During playback, press the

MODE button repeatedly until

Black Level setting appears.

• Stereo sound mode will not be changed when playing

DTS CD.

Press the ENTER button to switch ON/OFF.

ON (Default) : Makes the dark parts brighter.

OFF : Shows the original picture as recorded.

Press the RETURN button to exit.

NOTE:

• This function cannot be used during Dialog Speed

(refer to page 25).

–

DVD SETUP

In Setup menu, QUICK mode, CUSTOM mode and INITIALIZE mode are available (refer to pages 28-32).

QUICK mode consists of the setting menus frequently used, and they are accompanied with QUICK mark.

You can make all settings in CUSTOM mode.

(Default : AUTO)

STILL MODE

Language Setting

• Press the Cursor buttons (K or

L) for an item selection (AUTO,

FIELD, or FRAME), then press

the ENTER button.

Language setting can be varied with some DVDs or DivX^®

Subtitles recorded in discs.

DISPLAY

STILL MODE

AUTO

FIELD

FRAME

Press the SETUP button in stop mode.

Press the Cursor buttons (s or B) to select

CUSTOM, then press the ENTER button.

• The custom mode will appear.

• This function allows you to

adjust picture resolution and

quality in still mode.

• An individual picture on TV screen is called as “frame”,

which consists of two separate images called as “field”.

Some pictures may be blurred at the AUTO setting in

still mode due to their data characteristics.

• AUTO: Automatically selects the best resolution set-

ting (FRAME or FIELD) based on the data

characteristics of the pictures.

• FIELD: Select FIELD when the pictures are still unsta-

ble even if AUTO is selected. FIELD stabilizes

the pictures, although the picture quality may

become coarse due to the limited amount of

data.

• FRAME: Select FRAME to display relatively motionless

pictures in higher resolution. FRAME improves

the picture quality, although it may unstabilize

the pictures due to simultaneous output of two

field data.

Press the Cursor buttons (sor B)

to select LANGUAGE, then press

LANGUAGE

the ENTER button to confirm.

DIALOG

SUBTITLE

DISC MENU

OSD

DivX SUBTITLE

ORIGINAL

OFF

ENGLISH

OFF

Press the Cursor buttons (K or

L) to select an item, then press

the ENTER button.

(Default : ORIGINAL)

DIALOG

• Sets the audio language.

(Default : OFF)

SUBTITLE

• Sets the subtitle language.

DISC MENU (Default : ENGLISH)

• Sets the language for DVD Menu and title menu (for DivX^®).

QUICK

(Default : ENGLISH)

OSD

• Sets the language for the On-Screen display.

TV TYPE (DEFAULT: MULTI)

DivX SUBTITLE (Default: OFF)

• Press the Cursor buttons (K or

• Sets the DivX^®subtitle language.

DISPLAY

TV TYPE

L) to select a setting, then

NTSC

PAL

MULTI

press the ENTER button.

Press the Cursor buttons (K or L) to select a set-

ting, then press the ENTER button.

• Select a video system setting

between MULTI, NTSC and

• If OTHER is selected in the DIALOG, SUBTITLE or

DISC MENU, press four-digit number to enter the

code for the desired language (refer to the lan-

guage code list on page 32).

PAL.

• NTSC: Select this when your TV’s video format is

NTSC. If NTSC is selected, output format is

fixed to NTSC.

• PAL: Select this when your TV’s video format is PAL.

If PAL is selected, output format is fixed to PAL.

• MULTI: Automatically selects the suitable video out sys-

tem (PAL/NTSC) according to the format of the

inserted disc.

- For the discs recorded with NTSC system, the NTSC

signal will be output and pictures of the discs can be

viewed on an NTSC or Multi system TV.

- For the discs recorded with PAL system, the PAL sig-

nal will be output and pictures of the discs can be

viewed on a PAL system TV or Multi system TV.

•

Only the languages supported by the disc can be selected.

Press the SETUP button to exit and activate the

new settings.

NOTE:

• Language Setting for DIALOG and SUBTITLE may not

be available with some discs. Then use the AUDIO and

SUBTITLE buttons. Details are on page 26.

Display Setting

You can change certain aspects of the DVD display screens,

still mode, TV Type, Progressive and HDMI settings.

NOTES:

Press the SETUP button in stop mode.

Press the Cursor buttons (s or B) to select

CUSTOM, then press the

• If the AC power cord is disconnected while the unit is

turned on, the video format of opening screen is

altered. To keep the format, turn the unit off before

unplugging the AC power cord.

• When PAL signal is output from this unit, the image of

on-screen display will be distorted or will not be dis-

played at all. To bring back the on-screen display, select

MULTI using the DIMMER NTSC/PAL button on the

front panel then play a disc recorded in NTSC system,

or select NTSC. Refer to TV TYPE on page 17.

ENTER button.

•

The custom mode will appear.

DISPLAY

TV ASPECT

STILL MODE

TV TYPE

4:3 LETTER BOX

AUTO

MULTI

Press the Cursor buttons (s or

B) to select DISPLAY, then press

the ENTER button to confirm.

Press the Cursor buttons (K or

L) to select an item, then press the ENTER button.

PROGRESSIVE

PROG.MODE

HDMI SELECT

HDMI PICTURE

OFF

AUTO1

YCbCr

NORMAL

PROGRESSIVE

(Default : 4:3 LETTER BOX) QUICK

TV ASPECT

(Default: OFF) QUICK

• Press the Cursor buttons (K or

DISPLAY

L) for an item selection, then

press the ENTER button.

• Select 4:3 LETTER BOX for a

black bars appears on top and bot-

tom of the screen.

• Press the Cursor buttons (K or

TV ASPECT

STILL MODE

TV TYPE

PROGRESSIVE

PROG.MODE

HDMI SELECT

HDMI PICTURE

4:3 LETTER BOX

AUTO

MULTI

OFF

AUTO1

RGB

DISPLAY

TV ASPECT

L) to set PROGRESSIVE to ON

or OFF, then press the ENTER

button.

4:3 LETTER BOX

4:3 PAN

16:9 WIDE

4:3 SQUEEZE

SCAN

NORMAL

• The setting will be effective

• Select 4:3 PAN & SCAN for a full

height picture with both sides

trimmed.

• Select 16:9 WIDE if a wide-screen TV is connected to the

DVD player.

• Select 4:3 SQUEEZE when theTV screen is too large hor-

izontally at 16:9 WIDE setting and when it is impossible to

adjust the screen size using the TV’s controls.

when you exit the setup screen by pressing the SETUP

button.

•

When PROGRESSIVE is ON, P.SCAN appears on the

DVD player’s display after you exit the setup screen.

• Refer to page 12 for more details.

• In the HDMI output mode, even when PROGRESSIVE

is set to ON, signals are output always as Interlace.

–

DVD SETUP

PROG.MODE (Default: AUTO1)

DOLBY DIGITAL

(Default: BITSTREAM)

• Press the Cursor buttons (K or

L) to select a mode for the pro-

gressive scan output, then press

the ENTER button.

QUICK

AUDIO

DISPLAY

PROG.MODE

DRC

OFF

BITSTREAM

•

Set to BITSTREAM when the play-

er is connected to a Dolby Digital

decoder.

LPCM SELECT

DOLBY DIGITAL

DTS

BASS ENHANCER OFF

AUDIO MODE

HDMI AUDIO

AUTO1

AUTO2

VIDEO1

VIDEO2

VIDEO3

HDMI

CHANNEL

• AUTO1: mode suitable for images

•

This function is effective only for

on the film material.

the COAXIAL, OPTICAL and HDMI connections.

BITSTREAM:

• AUTO2: mode for images on the material of 30-frame film.

• VIDEO1: mode for normal video material.

• VIDEO2: mode for video material with less movements

DOLBY DIGITAL signals are output as Bitstream.

• For HDMI connection, if the connected

equipment is not compatible with the Dolby

Digital BITSTREAM, the signals are output as

PCM regardless of the setting.

• VIDEO3: mode for video material with many movements.

HDMI SELECT (Default:YCbCr)

• Select an HDMI output mode

between YCbCr and RGB.

• When the connected equipment

is not compatible with YCbCr,

HDMI signal is output as RGB

regardless of the setting.

DISPLAY

PCM: Convert Dolby Digital to PCM.

TV ASPECT

STILL MODE

TV TYPE

PROGRESSIVE

PROG.MODE

HDMI SELECT

HDMI PICTURE

4:3 LETTER BOX

AUTO

MULTI

OFF

AUTO1

YCbCr

DTS

(Default : BITSTREAM)

QUICK

NORMAL

• Set to BITSTREAM when the unit

is connected to a DTS decoder.

AUDIO

DRC

OFF

BITSTREAM

HDMI PICTURE (Default: NORMAL)

LPCM SELECT

DOLBY DIGITAL

DTS

BASS ENHANCER OFF

AUDIO MODE

HDMI AUDIO

BITSTREAM:

•

Select a HDMI picture mode between

NORMAL and ENHANCED.

DTS signals are output as

Bitstream.

HDMI

CHANNEL

DISPLAY

• Select ENHANCED if the black-

white contrast is not clear.

• This setting is effective only for

HDMI RGB output.

TV ASPECT

STILL MODE

TV TYPE

PROGRESSIVE

PROG.MODE

HDMI SELECT

HDMI PICTURE

4:3 LETTER BOX

AUTO

MULTI

OFF

AUTO1

YCbCr

•

For HDMI connection, if the

connected equipment is not compatible with the

DTS Bitstream, the signals are output as PCM

regardless of the setting.

NORMAL

Press the SETUP button to exit

and activate the new settings.

PCM:Convert DTS to PCM.

BASS ENHANCER (Default: OFF)

NOTE:

•

Set to ON for sound output on the

bass-woofer channel when 2-chan-

nel audio source is played back.

AUDIO

• Be sure to press the SETUP button, or the setting will

DRC

OFF

BITSTREAM

LPCM SELECT

DOLBY DIGITAL

DTS

BASS ENHANCER OFF

AUDIO MODE

HDMI AUDIO

not work.

•

This function is effective only for the

5.1ch AUDIO OUT jacks. Set the

AUDIO MODE to ANALOG and

HDMI

CHANNEL

Audio Setting

You can change some Audio settings. It only affects during the

playback of DVD discs.

ANALOG AUDIO to MULTI CHANNEL to set this function.

Press the SETUP button in stop mode.

• When SUB WOOFER is set to NONE in the Speaker

Configuration, BASS ENHANCER will be set to OFF

automatically.

Press the Cursor buttons (s or B) to select

CUSTOM, then press the ENTER button.

• The custom mode will appear.

AUDIO MODE (Default: HDMI

)

Press the Cursor buttons (s or B) to select

AUDIO, then the ENTER button to confirm.

Press the Cursor buttons (K or L) button to select

an item, then press the ENTER button.

• Select the sound is output from

whether HDMI jacks or 5.1ch

AUDIO OUT jacks.

HDMI: Sound is output via HDMI

connection. Output from

AUDIO

DRC

OFF

BITSTREAM

LPCM SELECT

DOLBY DIGITAL

DTS

BASS ENHANCER OFF

AUDIO MODE

HDMI AUDIO

HDMI

CHANNEL

• This menu display contains 2 pages. Press the Cursor

button (L) repeatedly to show the next page.

5.1ch AUDIO OUT connec-

tion may be restricted.

ANALOG: Sound is output via 5.1ch AUDIO OUT jacks.

Output from HDMI connection is cut off.

• Set to ANALOG when Super Audio CD is played back.

AUDIO

DRC

OFF

BITSTREAM

ANALOG AUDIO

CHANNEL

LPCM SELECT

DOLBY DIGITAL

DTS

BASS ENHANCER OFF

HDMI AUDIO (Default: 2 CHANNEL)

AUDIO MODE

HDMI AUDIO

HDMI

CHANNEL

•

Select the number of channels for

HDMI audio output between 2

CHANNEL and MULTI CHANNEL.

AUDIO

DRC (Dynamic Range Control)

(Default : ON)

DRC

OFF

BITSTREAM

LPCM SELECT

DOLBY DIGITAL

DTS

BASS ENHANCER OFF

AUDIO MODE

HDMI AUDIO

• Refer to the table on page 16 for

the actual output settings.

• Connect appropriate external

equipment for each setting and

AUDIO

• DRC function compresses the

HDMI

CHANNEL

DRC

OFF

BITSTREAM

LPCM SELECT

DOLBY DIGITAL

DTS

BASS ENHANCER OFF

AUDIO MODE

HDMI AUDIO

range of sound volume.

• DRC function is available only on

the discs that are recorded in the

Dolby Digital format.

HDMI

CHANNEL

set AUDIO MODE to HDMI beforehand to perform this

setting.

(Default : OFF)

LPCM SELECT

2 CHANNEL:

•

Set to ON when outputting in 48kHz.

AUDIO

2 channel signals are output from HDMI OUT jack.

Suitable for monitors or projectors compatible with

HDMI 2CH.

• This function is available only on

digital outputting of a disc record-

ed in 96kHz.

DRC

OFF

BITSTREAM

LPCM SELECT

DOLBY DIGITAL

DTS

BASS ENHANCER OFF

AUDIO MODE

HDMI AUDIO

HDMI

CHANNEL

MULTI CHANNEL:

• Sounds of the DVD-Audio which

exceed 96kHz will be output as

Multi channel signals are output from HDMI OUT

jack. Suitable for monitors or amplifiers compatible

with HDMI multi channels.

96kHz even if LPCM SELECT is set to OFF.

• This function is not effective for the HDMI sound output.

•

When MULTI CHANNEL is selected, the Speaker setting

menu for HDMI AUDIO will appear (refer to page 31).

When playing disc with copyright protection

• The sound will be down sampled at 48kHz, even if you

set to OFF.

–

DVD SETUP

ANALOG AUDIO (Default : 2 CHANNEL)

DELAY TIME

With 5.1-channel surround sound, ideally the distance

• Set AUDIO MODE to ANALOG beforehand to perform

this setting.

between the listening position and all the speakers

(exclude Sub woofer). The delay time setting can be

used to make the sound from the different speakers

reach the listening position at the same time.

2 CHANNEL:

Output 2ch sound from the 5.1ch

AUDIO OUT jacks.

MULTI CHANNEL: Output Multi channel sound from

the 5.1ch AUDIO OUT jacks.

Use the Cursor buttons (K or L) to select the setting item,

then press the ENTER button.

• Press the Cursor buttons (K or L) to select the speak-

er to set, then press the ENTER button.

AUDIO

ANALOG AUDIO

CHANNEL

MULTI CHANNEL

DISTANCE (Default : FEET)

METERS (when the ENTER

button is pressed):

AUDIO

DELAY TIME

DISTANCE

FRONT(L/R)

CENTER

SURROUND

DEFAULT

FEET

12ft

The unit of distance is set to

Press the SETUP button to exit and activate the

meters (m).

new settings.

FEET(when the ENTER button is

pressed):

The unit of distance is set to

feet (ft).

FRONT(L/R), CENTER,

SURROUND(L/R)

(DEFAULT : 12ft)

FRONT(L/R):

The distance can be set within

the range of 0 to 60 feet.

Speaker Setting for ANALOG AUDIO

When MULTI CHANNEL is selected for ANALOG AUDIO,

some speaker settings will be required.

AUDIO

DELAY TIME

• Set AUDIO MODE to ANALOG beforehand to perform

this setting.

DISTANCE

FRONT(L/R)

CENTER

SURROUND

DEFAULT

FEET

12ft

Press the Cursor buttons (K or

L) to select MULTI CHANNEL,

then press the ENTER button.

AUDIO

MULTI CHANNEL

CENTER, SURROUND:

These are depends on the

setting value of FRONT(L/R).

Speaker Configuration

DELAY TIME

Press the Cursor buttons (K or

L) to select the below items,

then press the ENTER button.

• The custom mode will appear.

CHANNEL LEVEL

AUDIO

FRONT(L/R)

NOTES:

18ft

17ft

16ft

15ft

14ft

13ft

12ft

• It is not possible to adjust this

item if CENTER and SUR-

ROUND have been set to NONE

in the Speaker Configuration set-

ting.

Speaker Configuration

• Press the Cursor buttons (K or

L) to select the speaker to set,

then press the ENTER button.

AUDIO

Speaker Configuration

FRONT(L/R)

CENTER

SUB WOOFER

SURROUND(L/R)

• When DEFAULT is selected and the ENTER button is

pressed, all the items are restored to their factory

default settings.

• Press the Cursor buttons

(K or L) button to select the

speaker size, then press the

ENTER button.

CHANNEL LEVEL

When the channel level differs from

AUDIO

CHANNEL LEVEL

AUDIO

FRONT(L/R)

each speaker, the adjustment can

be made in the unit of dB (-12dB to

0dB).

TEST TONE

FRONT(L)

0dB

LARGE

SMALL

CENTER

FRONT(R)

SUB WOOFER

SURROUND(R)

SURROUND(L)

TEST TONE:

FRONT(L/R), CENTER, SURROUND(L/R)

• Press the Cursor buttons

(K or L) to select TEST TONE,

then press the ENTER button.

The test tone will output from

each speaker in turn.

AUDIO

TEST TONE

LARGE: Select this when the connected speaker is

FRONT(L)

CENTER

FRONT(R)

SURROUND(R)

SURROUND(L)

0dB

-1dB

-2dB

-5dB

capable of playing back sounds of 100Hz or

more.

SMALL: Select this when the connected speaker is

capable of playing back sounds less than

100Hz.

CHANNEL LEVEL:

NONE: Select this when it is not connected. (It cannot

• Press the Cursor buttons (K or

L) to select the speaker to set,

then press the ENTER button.

• Press the Cursor buttons

(K or L) to select the desired

level for each speaker, then press

the ENTER button.

be set NONE on the FRONT speaker.)

AUDIO

FRONT(L)

SUB WOOFER

YES: Select this when SUB WOOFER is connected.

NONE: Select this when it is not connected.

0dB

-1dB

-2dB

-3dB

-4dB

-5dB

-6dB

NOTES:

• NONE is not available for SUB WOOFER when SMALL

is selected for FRONT (L/R).

NOTES:

• SMALL is not available for FRONT (L/R) when NONE

is selected for SUB WOOFER.

• ON is not available for BASS ENHANCER when NONE

is selected for SUB WOOFER.

• When playing back DVD audio, the sound may not

come out as set due to restrictions in the disc or the

player.

• While the test tone is being output, the channel bal-

ance adjustment cannot be made.

• When TEST TONE is selected, no test tone will be out-

put from SUBWOOFER.

• It is not possible to adjust this item for the speaker that

has been set to NONE in Speaker Configuration set-

ting.

Press the SETUP button to exit.

–

DVD SETUP

NOTES:

Speaker Setting for HDMI AUDIO

• This function may not work on some DVDs. Be sure if

When HDMI AUDIO is selected for

MULTI CHANNEL, the bass manage-

ment setting menu will appear. Set the

the RATINGS operates in the way you have set.

• The resume information will be cleared if you change

the parental level when the resume information is on.

AUDIO

MULTI CHANNEL

Speaker Configuration, delay time and

channel level for each speakers (front,

center, surround and sub woofer).

Speaker Configuration

DELAY TIME

CHANNEL LEVEL

To Change the Password:

1) Follow the steps 1 to 4 above.

2) Press the Cursor buttons (K or L) to select PASSWORD

CHANGE, then press the ENTER button.

3) Enter a new four-digit password, then press the ENTER button.

4) Press the SETUP button to exit.

Speaker Configuration

Set the size of each speaker between

LARGE and SMALL.

AUDIO

Speaker Configuration

IF YOU FORGET THE PASSWORD

FRONT(L/R)

CENTER

SUB WOOFER

SURROUND(L/R)

• The presence of the speakers is

detected automatically. Set the

detected speakers’ size.

Press 4, 7, 3, 7 at step

•

Password will be cleared and rating level will be set to ALL.

• When a speaker is not detected,

it's size is set as NONE.

Repeat steps to to re-establish the parental lock.

• Once a speaker is detected, you

cannot set it to NONE.

• The default setting is LARGE.

• During HDMI audio output, the

sound output via analog channels

may be restricted.

CONTROL LEVELS

AUDIO

CENTER

• ALL

LARGE

SMALL

NONE

Parental lock is canceled.

• Level 8

DVD software of any grade (adult/general/children) can

be played back.

DELAY TIME

• Levels 7 to 2

Same as DELAY TIME setting for “Speaker Setting for

ANALOG AUDIO” on page 30.

Only DVD software intended for general use and chil-

dren can be played back.

CHANNEL LEVEL

• Level 1

Same as CHANNEL LEVEL setting for “Speaker

Setting for ANALOG AUDIO” on page 30.

Only DVD software intended for children can be played

back, with those intended for adult and general use

prohibited.

Ratings Control

Others Setting

Ratings Control allows you to set a limit, which prevents your

children from viewing inappropriate materials on DVDs.

A four-digit password that you establish will give you the

control.

This function allows you to adjust Angle Icon availability, Auto

Power off, brightness of the Player’s display panel, slide show

mode, to obtain DivX^®registration code and DVD-Audio player

mode.

RATING LEVEL

You can set a viewing limit through Rating Level. Playback of

the discs will stop if the disc’s general rating exceeds the limit

you set.

Press the SETUP button in stop mode.

Press the Cursor buttons

(s or B) to select CUSTOM, then press ENTER.

• The custom mode will appear.

Press the SETUP button in stop mode.

Press the Cursor buttons

(s or B) to select Other, then

(

s or B) to select

OTHERS

press the ENTER button to

RATINGS

PASSWORD

ANGLE ICON

AUTO POWER OFF ON

PANEL DISPLAY

SLIDE SHOW

DivX(R) VOD

CUSTOM, then press the

confirm.

BRIGHT

5sec

Please enter

4-digit password.

ENTER button.

Press the Cursor buttons

(K or L) to select an item,

then press ENTER.

PLAYER MODE

AUDIO

• The custom mode will appear.

Press the Cursor buttons

(s or B) to select RATINGS,

(Default : ON)

ANGLE ICON

then press the ENTER button.

Press the Numeric buttons to

enter your four-digit password.

• Press the ENTER button repeat-

OTHERS

edly to turn ON or OFF.

ANGLE ICON

AUTO POWER OFF ON

PANEL DISPLAY

SLIDE SHOW

DivX(R) VOD

RATINGS

RATING LEVEL

BRIGHT

5sec

•

When doing this for the first time,

enter any four-digit number by

pressing the Numeric buttons

(except for 4737), then press the

ENTER button. That number will

be used as the password from the

second time onward. Record your

password in case you forget it.

ALL

PASSWORD CHANGE

PLAYER MODE

AUDIO

(Default :

AUTO POWER OFF

ON)

OTHERS

• Press the ENTER button repeat-

edly to turn ON or OFF.

• It will turn off the DVD player au-

tomatically after 30 minutes of

no use.

ANGLE ICON

AUTO POWER OFF ON

PANEL DISPLAY

SLIDE SHOW

DivX(R) VOD

RATINGS

RATING LEVEL

BRIGHT

5sec

ALL

PLAYER MODE

AUDIO

[NC-17]

[R]

[PG13]

[PG]

PANEL DISPLAY

Press the Cursor buttons (K or L) to select RAT-

ING LEVEL, then press the ENTER button.

Press the Cursor buttons (K or L) to select a desired

level, then press the ENTER button.

Press the SETUP button to exit and activate the

new settings.

(Default : BRIGHT)

OTHERS

PANEL DISPLAY

• Press the Cursor buttons

(K or L) to select a setting

(BRIGHT, DIMMER and AUTO),

then press the ENTER button.

• When AUTO is selected, the dis-

play dims only during playback.

BRIGHT

DIMMER

AUTO

–

DVD SETUP

• Some DivX^®VOD files are restricted with the limited

playable times (you cannot play them back beyond the

limit). If your DivX^®VOD file has such limit, the playback

confirmation screen will appear. Use the Cursor but-

tons (s or B) to select YES if you want to play back

the file, or to select NO if you do not wish to play it

back. Then, press the ENTER button to confirm the

selection.

(Default : 5sec)

SLIDE SHOW

• This adjusts the playback speed

OTHERS

SLIDE SHOW

of the JPEG SLIDE SHOW.

• Press the Cursor buttons

(K or L) to select between 5 sec

and 10 sec, then press the

ENTER button.

5sec

10sec

DivX(R) VOD

• Please send your inquiries regarding the VOD files to

DivX^®, Inc.

Press the SETUP button to exit.

• This player allows you to use the

DivX^®Video-On-Demand (VOD)

services.You can play back the

files purchased or rental from

OTHERS

DivX(R) VOD

Your registration code is:

To learn more visit

www.divx.com/vod

the VOD services.You need to

have a registration code to pur-

chase or rental VOD files. Please visit

www.divx.com/vod for more details.

Reset to the Default Settings

(except for Ratings Control)

This allows you to return all selections of SETUP (except for

RATINGS) to their default settings.

(Default : AUDIO)

PLAYER MODE

Press the SETUP button in stop mode.

Press the Cursor buttons (s or B) to select

INITIALIZE, then press the ENTER button.

Press the Cursor buttons (K or L) to select YES,

then press the ENTER button.

Press the SETUP button to exit.

• Press the ENTER button repeat-

edly to select AUDIO or VIDEO.

• AUDIO: Select to play back gen-

eral contents of DVD-

OTHERS

ANGLE ICON

AUTO POWER OFF ON

PANEL DISPLAY

SLIDE SHOW

DivX(R) VOD

BRIGHT

5sec

PLAYER MODE

AUDIO

Audio.

• VIDEO: Select to play back

DVD-Video contents included in DVD-Audio.

NOTE:

NOTES:

•

If you do not wish to initialize, select NO at step

• You cannot play back the DivX^®VOD files obtained with

different registration codes on this player.

• You cannot play back the DivX^®VOD files, of which

rental period has been expired. In such case, press the

MENU button and select other files that can be played

back.

Language Code List

Language

Code

Language

Code

Language

Code

Language

Code

A-B

French [FRE]

Frisian

Galician

Georgian

German [GER]

Greek [GRE]

Greenlandic

Guarani

Gujarati

Hausa

Hebrew

Hindi

5264

5271

5358

5747

5051

5158

5758

5360

5367

5447

5569

5455

5467

Macedonian

Malagasy

Malay

Malayalam

Maltese

Maori

5957

5953

5965

5958

5966

5955

5964

5961

5960

6047

6051

6061

Siswat

6565

6557

6558

6561

5165

6567

6569

6568

Abkhazian

Afar

Afrikaans

Albanian

Amharic

Arabic

Armenian

Assamese

Aymara

Azerbaijani

Bashkir

Basque

4748

4747

4752

6563

4759

4764

5471

4765

4771

4772

4847

5167

4860

5072

4854

4855

4864

4853

5971

4851

Slovak [SLO]

Slovenian

Somali

Spanish [SPA]

Sundanese

Swahili

Swedish [SWE]

Tagalog

Tajik

Tamil

Tatar

Telugu

Thai

Tibetan

Tigrinya

Tonga

Tsonga

Turkish [TUR]

Turkmen

Twi

Marathi

Moldavian

Mongolian

Nauru

6658

6653

6647

6666

6651

6654

4861

6655

6661

6665

6664

6657

6669

Nepali

Norwegian [NOR]

O-R

Occitan

Oriya

Oromo(Afan)

Panjabi

Hungarian [HUN]

I-K

Bengali;Bangla

Bhutani

Bihari

6149

6164

6159

6247

6265

5247

6258

6266

6367

6459

6461

6467

Icelandic [ICE]

Indonesian

Interlingua

Interlingue

Inupiak

Irish [IRI]

Italian [ITA]

Japanese [JPN]

Javanese

Kannada

Kashmiri

Kazakh

Kinyarwanda

Kirghiz

Kirundi

Korean [KOR]

Kurdish

5565

5560

5547

5551

5557

5347

5566

5647

5669

5760

5765

5757

6469

5771

6460

5761

5767

Bislama

Breton

Pashto;Pushto

Persian

Bulgarian [BUL]

Burmese

Byelorussian

C-E

Polish [POL]

Portuguese [POR]

Quechua

Rhaeto-Romance

Romanian [RUM]

Russian [RUS]

Samoan

Sangho

Sanskrit

Scots Gaelic

Serbian

Serbo-Croatian

Sesotho

Setswana

Shona

Sindhi

Cambodian

Catalan

5759

4947

7254

4961

5464

4965

5047

6058

5160

5161

5166

U-Z

Ukrainian

Urdu

Uzbek

Vietnamese

Volapuk

Welsh

Wolof

Xhosa

Yiddish

Yoruba

Zulu

6757

6764

6772

6855

6861

4971

6961

7054

5655

7161

7267

Chinese [CHI]

Corsican

Croatian

Czech [CZE]

Danish [DAN]

Dutch [DUT]

English [ENG]

Esperanto

Estonian

6559

6553

6547

5350

6564

6554

6566

6660

6560

6550

6555

L-N

Laothian

Latin

Latvian;Lettish

Lingala

Lithuanian

5861

5847

5868

5860

5866

F-H

Faroese

Fiji

Finnish [FIN]

5261

5256

5255

Singhalese

If you choose a language that has a three-letter language code (written in bracket), the code will be displayed every time you change the Au-

dio or Subtitle Language setting on page 26. If you choose any other languages, ‘---’ will be displayed instead.

–

TROUBLESHOOTING GUIDE

If the DVD player does not perform properly when operated as instructed in this Operating Instruction, check the player, con-

sulting the following checklist.

Problem

Solution

Page

No power

Check if the AC power cord is properly connected.

Unplug the AC cord once, and wait for 5-10 seconds and then plug it in again.

No sound or picture

Check if the TV is turned on.

Check the video and HDMI connection.

Check the AUDIO/VIDEO cable connections.

Check if the PURE DIRECT is set to ON. If it is the case, set it to OFF

Check if the PROGRESSIVE mode is set correctly.

15, 16

13-15

12, 28

Distorted picture

Sometimes a small amount of picture distortion may appear.

This is not a malfunction.

Connect the DVD player directly to the TV.

Check if the PROGRESSIVE mode is set correctly.

Check the TV TYPE. (MULTI, NTSC or PAL)

12, 28

17, 28

Completely distorted picture or black/

white picture with DVD

Connect the DVD player directly to the TV.

Make sure the disc is compatible with the DVD player.

No sound or distorted sound

Adjust the volume.

Check that the speakers are connected correctly.

The HDMI sound is not output during PURE DIRECT or

when AUDIO MODE is set to ANALOG.

13-15

17, 29

No audio at digital output

Check the digital connections.

Check the audio settings.

Digital signals cannot be output with Super Audio CDs.

Use analog connections.

13, 16

29,30

13, 16

Area/layer of Super audio CD being played (MULTI / STEREO / CD)

does not match amplifier connections.

No image from HDMI connection

Check the HDMI connection. (Check the status of the HDMI related indications.) 16, 17

Check whether the connected monitor equipment or other equipment supports

HDCP. (This player will not output a video signal unless the other equipment

supports HDCP.)

Connect the DVD player to the display equipment using the Audio/Video

cables (supplied), and check the HDMI settings.

Check whether the output format of this player (HDMI FORMAT)

matches the supported input format of other connected equipment.

Check if the PURE DIRECT is set to ON.

13-16, 29

If it is the case, set it to OFF.

Picture freezes momentarily during

playback

Check the disc for fingerprints/scratches and clean with a soft cloth wiping

from centre to edge.

Clean the disc.

Disc cannot be played back

Clean the disc.

Ensure the disc label is facing up.

Check if the disc is defective by trying another disc.

Cancel the ratings control or change the control level.

Insert a correct disc that can be played back on this player.

No return to start-up screen when disc

is removed

Reset the player by turning it off, then on again.

The DVD player does not respond to

the remote control

Aim the remote control directly at the sensor on the front of the player.

Reduce the distance to the player.

Replace the batteries in the remote control.

Re-insert the batteries with their polarities (+/ signs) as indicated.

Buttons do not work or the player

stops responding

To completely reset the player, unplug the AC cord from the AC

outlet for 5-10 seconds.

The DVD player does not respond to

some operating commands during

playback

Operations may not be permitted by the disc.

Refer to the instructions of the disc.

The DVD player cannot read

CDs/DVDs

Use a commonly available CD/DVD cleaner to clean the lens before

sending the DVD player for repair.

Angle does not switch

The angle cannot be switched for DVDs which do not contain

multiple angles. In some cases multiple angles are only recorded for

specific scenes.

Playback does not start when the title

is selected

Check the "RATINGS" setting.

The password for rating level has been

forgotten

Enter the default password "4737", then your forgotten password will

be cleared.

NOTES:

• Some functions are not available in specific modes, but this is not a malfunction. Read the description in this Operating

Instruction for details on correct operations.

• Playback from a desired track and random playback are not available during program playback.

• Some functions are prohibited on some discs.

–

SPECIFICATIONS

SIGNAL SYSTEM

NTSC/PAL color

AUDIO OUTPUT PROPERTIES

(1) Frequency response

1 DVDs (linear PCM) : 4Hz to 22kHz (48kHz sampling)

: 4Hz to 44kHz (96kHz sampling)

: 4Hz to 88kHz (192kHz sampling)

APPLICABLE DISCS

(1) DVD-Video/DVD-Audio Discs

1-layer 12cm single-sided discs, 2-layer 12cm single-sided

discs, 2-layer 12cm double-sided discs (1 layer per side)

1-layer 8cm single-sided discs, 2-layer 8cm single-sided

discs, 2-layer 8cm double-sided discs (1 layer per side)

(2) Super Audio CD

2 CDs

3 Super Audio CD

(2) S/N ratio

: 4Hz to 20kHz

: 4Hz to 100kHz

: 115dB

(3) Total harmonic distortion : 1kHz CD: 0.004%

(4) Dynamic range

: DVD: 100dB

CD: 98dB

(3) DVD-R/DVD-RW

(4) Compact discs (Audio CD)

12cm discs, 8cm discs

DIGITAL AUDIO OUTPUT

(5) CD-R/CD-RW

Optical digital output: Optical connector, 1 set

Coaxial digital output: Pin jack, 1 set

S-VIDEO OUTPUT

Y output level: 1Vp-p (75Ω/ohms)

POWER SUPPLY

C output level: 0.286Vp-p

AC 120V, 60Hz

Output connectors: S connectors, 1 set

POWER CONSUMPTION

VIDEO OUTPUT

15W (Standby: 0.4W)

Output level: 1Vp-p (75Ω/ohms)

Output connector: Pin jacks, 1 set

MAXIMUM EXTERNAL DIMENSIONS

W: 17-3/32" (435mm)

COMPONENT OUTPUT

H: 2-61/64" (75mm)

Y output level: 1Vp-p (75Ω/ohms)

PB/CB output level: 0.648Vp-p (75Ω/ohms)

PR/CR output level: 0.648Vp-p (75Ω/ohms)

Output connector: Pin jacks, 1 set

D: 12-13/64" (310mm)

(including protruding parts)

MASS

HDMI OUTPUT

5.72 lbs (2.6 kg)

HDMI jack, 1 set

REMOTE CONTROL UNIT

RC-1017

AUDIO OUTPUT

Output level: 2Vrms

Infrared pulse type

2 channel (L, R) output connector: Pin jack, 1 set

Multi channel (FL, FR, C, SL, SR, SW): Pin jack, 1set

Supply: DC 3V, 2 R6P/AA batteries

MAINTENANCE

Cleaning the Cabinet

• Use a soft cloth slightly moistened with a mild detergent solution. Do not use a solution containing alcohol, spirits,

ammonia or abrasives.

Cleaning Discs

• When a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the center out. Do not wipe in a circular

motion.

• Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or

antistatic spray intended for analogue records.

Cleaning the disc lens

• If the player still does not perform properly when it is operated while referring to the relevant sections and to “TROU-

BLESHOOTING GUIDE” in this Operating Instruction, the laser optical pickup unit may be dirty. Consult your dealer or

an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.

Disc Handling

• Use discs which have the following logos on them.

• Handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs.

• Always store the disc in its protective case when it is not used.

•

Note that discs with special shapes (heart-shaped discs, octagonal discs, etc.) cannot be

played on the this product. Do not attempt to play such discs, as they may damage the player.

–

MEMO

–

TOKYO, JAPAN

www.denon.com

Denon Brand Company, D&M Holdings Inc.

Printed in China

00D 511 4658 000

1VMN23655

E6EE0UD *****

Nokia 1260 User Manual
Motorola MOTORAZR V3r User Manual
Motorola I1 User Manual
Krell Industries CD Player User Manual
JVC KD AR200 User Manual
Echo Bear Cat SC3305 User Manual
Clarion DXZ865MP User Manual
Cables to Go 28652 User Manual
Blackberry Curve 8310 User Manual
BenQ CL 71 User Manual